Since commit [1], the MMU support is mandatory for MMU-capable ARM
cores. This includes the arm926t ARM core used the
qemu_arm_versatile_nommu configuration.
From [2]
"I don't think supporting ARMv5 noMMU makes much sense, as
explained in the commit log. Supporting ARMv7-M definitely makes
sense, but not ARMv5 noMMU."
Remove this defconfig.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/2477067386
[1] 8c925613dc
[2] http://lists.busybox.net/pipermail/buildroot/2022-May/643064.html
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Switch U-Boot from vendor downstream version to upstream. Since the
upstream U-Boot uses binman to build the bootable binary (flash.bin) the
need for the iMX specifc prepare script is no longer required.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
This patch adds support for Xilinx Kria KV260 starter kit.
KV260 features can be found here:
https://www.xilinx.com/products/boards-and-kits/kv260.html
While the Kria SOM is based on a ZynqMP SoC, there are some key
boot config differences from the other ZynqMP evaluation boards.
1. There are no boot switches on Kria SOMs. The boot mode is thus
hard configured for QSPI flash. A pre-programmed boot.bin comes
with every Starter Kit. U-Boot can then find the Linux kernel and
file system on the SD card.
Optional instructions for updating the boot.bin in the QSPI flash
can be found in the readme.txt file and the link below.
https://xilinx-wiki.atlassian.net/wiki/spaces/A/pages/1641152513/Kria+K26+SOM
2. Kria SOMs use UART1 for the console instead of UART0. For this
reason, Kria Starter Kits will use a separate extlinux.conf file
from other ZynqMP evaluation boards.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch bumps configs/zynq_xxx_defconfigs to Xilinx software release 2022.1
which includes the following updates:
- U-Boot bumped to 2022.01
- Linux bumped to 5.15.19
- rootfs changed from CPIO to EXT4
- extlinux.conf for distro boot support
- U-Boot migrated from git clone to tarball for faster builds
This patch has been build and run tested on a ZC706 evaluation board.
This patch has been build tested only for zed, microzed and qmtech boards.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch fixes the DP audio and video PLL configurations for the
zynqmp-zcu106-revA evaluation board.
The Linux DP driver expects the DP to be using the following PLL config:
- DP video PLL should use the VPLL (0x0)
- DP audio PLL should use the RPLL (0x3)
Register 0xFD1A0070 configures the DP video PLL.
Register 0xFD1A0074 configures the DP audio PLL.
This patch was build and run tested on a zynqmp-zcu106-revA target board.
Upstream-Status: submitted (https://lore.kernel.org/all/62538b4a04dee28a6fc8ac5b85f8c845a5a76aa4.1651740988.git.michal.simek@amd.com/)
This patch will be removed from buildroot in a future release when no longer necessary.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
When BR2_TARGET_OPTEE_OS=y, mkimage_fit_atf.sh is executed with two additional
variables so that the ITS file contains an additional node for the TEE binary.
Then the TEE binary will be packaged into the ITB in addition to TF-A and
U-Boot.
Signed-off-by: Thomas Perrot <thomas.perrot@bootlin.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch provides defconfig and basic support for Andes
45 series RISC-V architecture on AE350 platform.
http://www.andestech.com/en/products-solutions/andeshape-platforms/ae350-axi-based-platform-pre-integrated-with-n25f-nx25f-a25-ax25/
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Signed-off-by: Alan Kao <alankao@andestech.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Switch to extlinux instead of U-Boot boot script. Drop custom boot
script and genimage config. Instead use common orangepi files from
board/orangepi/common. To help extlinux to find DTB without U-Boot
environment changes, do not strip arm64 board specific directory
from DTB name when installing it in /boot directory. For this
purpose use BR2_KERNEL_DTB_KEEP_DIRNAME config option. Finally,
tidy up configuration file adding section names.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
- Bump Linux to version 5.4.137
- Bump U-Boot to add new targets, version remains the same
- Drop BR2_ROOTFS_OVERLAY and remove S09modload script because it was
only used by PFE and now PFE is loaded directly by the kernel
- Use Image.gz instead of Image to have a compressed kernel
- Rename ucls1012a.its to br2-ucls1012a.its since post-build.sh and
post-image.sh use different name. This fixes the bug that didn't
allow the creation of the part0-000000.itb file.
Signed-off-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Changes:
* Switch to common orangepi scenario for multiple boards (board/orangepi/common) to create an SD image.
* Exclude FAT partition, it is no longer needed for U-Boot.
* Switch SD image from MBR to GPT for partition-uuid to work.
* Switch to extlinux, this is convenient for debugging.
Signed-off-by: Sergey Kuzminov <kuzminov.sergey81@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Technologic Systems has rebranded as embeddedTS with the current
domain eventually going offline. Update web/doc URLs to correct
resource locations.
Signed-off-by: Kris Bahnsen <kris@embeddedTS.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Fixes the following error during image generation:
ERROR: hdimage(sdcard.img): part boot: 'partition-type' is only valid
for mbr and hybrid partition-table-type
Fixes: https://gitlab.com/buildroot.org/buildroot/-/jobs/2103784375
Signed-off-by: Marcus Hoffmann <marcus.hoffmann@othermo.de>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Add a U-Boot config fragment to set the correct control device tree file for
each board, rather than using the default (zcu100).
Signed-off-by: Neal Frager <neal.frager@xilinx.com>
Tested-by: Peter Korsgaard <peter@korsgaard.com>
[Peter: reword commit message, rename fragment files]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Genimage 15 restricted the partition-type option to mbr and hybrid
partition-table-type and now prints a warning when it is used [1]:
ERROR: hdimage(disk.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
[1] 1d72d8091f
So let's use for EFI System partition:
'partition-type-uuid = c12a7328-f81f-11d2-ba4b-00a0c93ec93b'
and for Root partition (32-bit ARM):
'partition-type-uuid = 69DAD710-2CE4-4E3C-B16C-21A1D49ABED3'
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1929717242
FTR, the magic UUID are from:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Changes:
* Exclude FAT partition, it is no longer needed for U-Boot.
* Switch the rootfs partition from MBR to GPT for partition-uuid to work.
* Switch to extlinux, this is convenient for debugging.
* Create common scenarios for multiple boards to create an SD image:
board/orangepi/common. Currently only orangepi_zero makes use of the
common infrastructure.
Signed-off-by: Sergey Kuzminov <kuzminov.sergey81@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
[Arnout: remove rootfs size = 63M and remount rw]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Actually genimage fails to create final image with:
```
ERROR: hdimage(disk.img): partition [MBR] (offset 0x1b8, size 0x48) overlaps previous partition boot (offset 0x0, size 0x200)
ERROR: hdimage(disk.img): bootloaders, etc. that overlap with the partition table must declare the overlapping area as a hole.
```
This is because genimage 15 is less permissive than before, so let's add
holes = {"(440; 512)"} to leave room to MBR.
The generated image is identical to the image generated by the previous
version of genimage.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1865935249
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
This patch:
- adds support for Xilinx ZCU102 evaluation board
- ZCU102 features can be found here:
https://www.xilinx.com/products/boards-and-kits/zcu102.html
Signed-off-by: Neal Frager <neal.frager@xilinx.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
[Giulio: only build tested]
[Peter: use git describe for git hashes for clarity, add DEVELOPERS entry]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
This patch:
- bumps ATF to Xilinx v2.6: mainline v2.6 requires patch to build
- bumps U-Boot to Xilinx 2022.01: important drivers not in mainline
- bumps Linux to Xilinx 5.15: important drivers not in mainline
- deletes board/zynqmp/patches directory: patches already in mainline
- modifies board/zynqmp/genimage.cfg: U-Boot 2022.01 uses u-boot.itb format
- adds extlinux.conf to vfat bootfs
- modifies U-Boot to unified xilinx_zynqmp_virt_defconfig (supports all boards)
- adds support for SPL pm_cfg_obj.c loading to PMU firmware
- enables support for host machines without OpenSSL required by U-Boot and Linux
Signed-off-by: Neal Frager <neal.frager@xilinx.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
[Giulio: only build tested]
[Peter: use git describe for git hashes for clarity]
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
The BL i.MX8M Mini is a baseboard that includes the SoM SL i.MX8M Mini.
https://www.kontron.com/produkte/baseboard-bl-i.mx8m-mini/p158549
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
[Arnout: explicitly set BR2_cortex_a53=y]
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
ERROR: hdimage(sdcard.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
To fix the first genimage error report, change 'partition-type' entries
to the appropriate 'partition-type-uuid'. Then genimage starts to
complain about overlaps:
ERROR: hdimage(sdcard.img): partition [GPT array] (offset 0x100000, size 0x4000) overlaps previous partition u-boot (offset 0x2000, size 0x102000)
ERROR: hdimage(sdcard.img): bootloaders, etc. that overlap with the partition table must declare the overlapping area as a hole.
To fix the second genimage error report, update the size of bootloader
file. Do not reserve additional space for GPT partition table since
new genimage is able to keep track of it.
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/2021478371
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Genimage 15 restricted the partition-type option to mbr and hybrid
partition-table-type and now prints a warning when it is used [1]:
ERROR: hdimage(disk.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
[1] 1d72d8091f
So let's use for EFI System partition:
'partition-type-uuid = c12a7328-f81f-11d2-ba4b-00a0c93ec93b'
and for Root partition (64-bit ARM/AArch64):
'partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae'
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1929717241
FTR, the magic UUID are from:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Genimage 15 restricted the partition-type option to mbr and hybrid
partition-table-type and now prints a warning when it is used [1]:
ERROR: hdimage(disk.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
[1] 1d72d8091f
So let's use for EFI System partition:
'partition-type-uuid = c12a7328-f81f-11d2-ba4b-00a0c93ec93b'
and for Root partition (64-bit ARM/AArch64):
'partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae'
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1929717240
FTR, the magic UUID are from:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Genimage 15 restricted the partition-type option to mbr and hybrid
partition-table-type and now prints a warning when it is used [1]:
ERROR: hdimage(disk.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
[1] 1d72d8091f
So let's use for EFI System partition:
'partition-type-uuid = c12a7328-f81f-11d2-ba4b-00a0c93ec93b'
and for Root partition (64-bit ARM/AArch64):
'partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae'
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1929717243
FTR, the magic UUID are from:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Genimage 15 restricted the partition-type option to mbr and hybrid
partition-table-type and now prints a warning when it is used [1]:
ERROR: hdimage(disk.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
[1] 1d72d8091f
So let's use for EFI System partition:
'partition-type-uuid = c12a7328-f81f-11d2-ba4b-00a0c93ec93b'
and for Root partition (64-bit ARM/AArch64):
'partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae'
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1929717059
FTR, the magic UUID are from:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Genimage 15 restricted the partition-type option to mbr and hybrid
partition-table-type and now prints a warning when it is used [1]:
ERROR: hdimage(disk.img): part boot: 'partition-type' is only valid for mbr and hybrid partition-table-type
[1] 1d72d8091f
So let's use for EFI System partition:
'partition-type-uuid = c12a7328-f81f-11d2-ba4b-00a0c93ec93b'
and for Root partition (64-bit ARM/AArch64):
'partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae'
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/1929717055
FTR, the magic UUID are from:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add patch to fix linux bug:
```
HOSTLD scripts/dtc/dtc
/usr/bin/ld: scripts/dtc/dtc-parser.tab.o:(.bss+0x10): multiple definition of `yylloc'; scripts/dtc/dtc-lexer.lex.o:(.bss+0x0): first defined here
collect2: error: ld returned 1 exit status
```
Fixes:
https://gitlab.com/buildroot.org/buildroot/-/jobs/2021478164
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
RK3399_ROCKPRO64 has been picked from pine64/rockpro64 but here we deal
with orangepi-rk3399, so let's change the label to RK3399_ORANGEPI.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Linux config already enabled drm-virtio for graphics output, but not the
corresponding virtio-input / evdev drivers for input or the compatibility fb
option.
Enable them so keyboard/mouse input works and /dev/fb0 is provided.
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
Since Qemu 6.0.0 [1], a warning appear in the log if a short-form
boolean option is used.
[1] https://git.qemu.org/?p=qemu.git;a=commitdiff;h=ccd3b3b8112b670fdccf8a392b8419b173ffccb4
Signed-off-by: Romain Naour <romain.naour@gmail.com>
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Dick Olsson <hi@senzilla.io>
Signed-off-by: Yann E. MORIN <yann.morin.1998@free.fr>
The CM4 IO Board is equipped with an on-board RTC connected over I2C,
and has USB 2.0 host ports.
This commit loads the appropriate overlays to enable both. The USB 2.0
interface is by default disabled on CM4 to reduce the power
consumption so it needs to be explicitly enabled on the CM4 IO Board
to use the USB ports.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The CM4 IO Board is equipped with an on-board RTC connected over I2C,
and has USB 2.0 host ports.
This commit loads the appropriate overlays to enable both. The USB 2.0
interface is by default disabled on CM4 to reduce the power
consumption so it needs to be explicitly enabled on the CM4 IO Board
to use the USB ports.
Signed-off-by: Peter Seiderer <ps.report@gmx.net>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The mmc block device number can vary, so passing a mmc block device to
specify the location of the rootfs is not a reliable
approach. Instead, use the root=PARTUUID=<uuid> mechanism, where the
uuid is found by U-Boot.
Signed-off-by: Sergey Kuzminov <kuzminov.sergey81@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
commit 0d0f84d200
added the missing host-dtc dependency to riscv-isa-sim.
The spike simulator calls the dtc binary at its startup. The host dtc
command needs to be in the PATH at that time.
This commit add the buildroot host binary directory into the PATH of the
start.sh helper script. It make sure spike will use the buildroot dtc
version. This commit fixes this start.sh script on host not providing
the dtc command. Since the "spike" binary is now in the PATH, the
binary name is also simplified.
Signed-off-by: Julien Olivain <ju.o@free.fr>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Bump U-Boot to 2022.01 and kernel to 5.15.13.
After the conversion to U-Boot device model, the SD card is
device '1', so change the boot script accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
The Bamboo board is an evaluation board for PowerPC 440EP CPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
PowerNV is the platform using the OPAL [1] firmware on OpenPOWER
systems. OPAL first loads a kernel and an initramfs image based on
buildroot including a second boot loader petitboot [2]. The latter
does device discovery and kexecs a new Linux image from disk or
network.
QEMU implements PowerNV machines [3] for the POWER8, POWER9 and
Power10 processors which are used for dev and tests. POWER8 images
being compatible with POWER9 and Power10, simply add a single
qemu_ppc64le_powernv8 board for all.
The QEMU script boots directly from a nvme disk because it is simple
enough but a real system would boot from a ramfs first.
[1] https://github.com/open-power/skiboot/blob/master/doc/overview.rst
[2] https://github.com/open-power/petitboot/
[3] https://qemu.readthedocs.io/en/latest/system/ppc/powernv.html
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
