4e4545246f
Add two new sample defconfigs oriented towards real PC targets. It adds two variants for BIOS and EFI boot strategy. On the build side we enable eudev to autoload relevant kernel modules/support when necessary. It adds a bunch of drivers and extra filesystem support which is by no means extensive/complete, mostly geared towards the hardware i've got at hand to test with. This is accomplished by adding on top of the Qemu x86_64 kernel sample config. Build connman since by using eudev network interfaces get renamed on boot thus complicating any form of automatic and friendly bringup. It also makes Wi-Fi configuration/support easier. In principle these base defconfigs should work just fine for other storage media != pendrive like sata or ssd disk, however driver support isn't there quite yet, and pendrive is mostly supported by usb storage plus the usual usb host controller drivers. Tested on old Lenovo laptop (BIOS) and Asus Zenbook (EFI). Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
63 lines
1.8 KiB
Plaintext
63 lines
1.8 KiB
Plaintext
# Architecture
|
|
BR2_x86_64=y
|
|
|
|
# Toolchain, required for eudev (to autoload drivers)
|
|
BR2_TOOLCHAIN_BUILDROOT_WCHAR=y
|
|
|
|
# System
|
|
BR2_TARGET_GENERIC_GETTY_PORT="tty1"
|
|
BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y
|
|
|
|
# Required tools to create bootable media
|
|
BR2_PACKAGE_HOST_GENIMAGE=y
|
|
|
|
# Bootloader
|
|
BR2_TARGET_GRUB2=y
|
|
|
|
# Filesystem / image
|
|
BR2_TARGET_ROOTFS_EXT2=y
|
|
BR2_TARGET_ROOTFS_EXT2_4=y
|
|
# BR2_TARGET_ROOTFS_TAR is not set
|
|
BR2_ROOTFS_POST_IMAGE_SCRIPT="board/pc/post-image.sh"
|
|
|
|
# Linux headers same as kernel, a 4.5 series
|
|
BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_5=y
|
|
|
|
# Kernel
|
|
BR2_LINUX_KERNEL=y
|
|
BR2_LINUX_KERNEL_CUSTOM_VERSION=y
|
|
BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="4.5.2"
|
|
BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
|
|
BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/qemu/x86_64/linux-4.5.config"
|
|
BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="board/pc/linux-extras.config"
|
|
BR2_LINUX_KERNEL_INSTALL_TARGET=y
|
|
|
|
# Firmware
|
|
BR2_PACKAGE_LINUX_FIRMWARE=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_ATHEROS_9170=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_ATHEROS_9271=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_3160=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_3168=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_5000=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_6000G2A=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_6000G2B=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_7260=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_7265D=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_8000C=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_IWLWIFI_8265=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_RALINK_RT73=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_RALINK_RT2XX=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_RTL_8169=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_RTL_81XX=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_RTL_87XX=y
|
|
BR2_PACKAGE_LINUX_FIRMWARE_RTL_88XX=y
|
|
|
|
# Packages
|
|
#
|
|
# Use connman so that networking setup is simpler, via connmanctl tool
|
|
# acpid is for seamless power button support
|
|
BR2_PACKAGE_ACPID=y
|
|
BR2_PACKAGE_CONNMAN=y
|
|
BR2_PACKAGE_CONNMAN_CLIENT=y
|
|
BR2_PACKAGE_CONNMAN_WIFI=y
|