0d71ab4172
Bump U-boot version to 2015.07 from the mainline repository. Since there is SPL support for the wandboard in the U-boot 2015.07, it is now possible to boot the same U-boot image for all wandboard variants (solo/dual/quad). Bump kernel version to 3.14.28_1.0.0 from the wandboard git repository. Tested on Wandboard Solo, Wandboard Dual and Wandboard Quad. Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com> Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
29 lines
2.3 KiB
Plaintext
29 lines
2.3 KiB
Plaintext
baudrate=115200
|
|
boot_fdt=try
|
|
bootcmd=run findfdt; mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if run loadimage; then run mmcboot; else run netboot; fi; fi; else run netboot; fi
|
|
bootdelay=3
|
|
bootscript=echo Running bootscript from mmc ...; source
|
|
console=ttymxc0
|
|
ethact=FEC
|
|
ethaddr=00:1f:7b:b2:05:ee
|
|
ethprime=FEC
|
|
loadaddr=0x12000000
|
|
fdt_addr=0x18000000
|
|
fdt_high=0xffffffff
|
|
fdtfile=undefined
|
|
findfdt=if test $board_rev = MX6Q ; then setenv fdtfile imx6q-wandboard.dtb; fi; if test $board_rev = MX6DL ; then setenv fdtfile imx6dl-wandboard.dtb; fi; if test $fdtfile = undefined; then echo WARNING: Could not determine dtb to use; fi;
|
|
loadfdt=ext2load mmc ${mmcdev}:${mmcpart} ${fdt_addr} /boot/${fdtfile}
|
|
loadbootscript=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};
|
|
loadimage=ext2load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}
|
|
mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot}; run videoargs
|
|
videoargs=setenv nextcon 0; if hdmidet; then setenv bootargs ${bootargs} video=mxcfb${nextcon}:dev=hdmi,1280x720M@60,if=RGB24; setenv fbmen fbmem=28M; setexpr nextcon ${nextcon} + 1; else echo - no HDMI monitor;fi; i2c dev 1; if i2c probe 0x10; then setenv bootargs ${bootargs} video=mxcfb${nextcon}:dev=lcd,800x480@60,if=RGB666,bpp=32; if test 0 -eq ${nextcon}; then setenv fbmem fbmem=10M; else setenv fbmem ${fbmem},10M; fi; setexpr nextcon ${nextcon} + 1; else echo '- no FWBADAPT-7WVGA-LCD-F07A-0102 display';fi; setenv bootargs ${bootargs} ${fbmem}
|
|
mmcboot=echo Booting from mmc ...; run mmcargs; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
|
|
mmcdev=0
|
|
mmcpart=1
|
|
mmcroot=/dev/mmcblk2p1 rootwait rw
|
|
netargs=setenv bootargs console=${console},${baudrate} root=/dev/nfs ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp
|
|
netboot=echo Booting from net ...; run netargs; if test ${ip_dyn} = yes; then setenv get_cmd dhcp; else setenv get_cmd tftp; fi; ${get_cmd} ${image}; if test ${boot_fdt} = yes || test ${boot_fdt} = try; then if ${get_cmd} ${fdt_addr} /boot/${fdtfile}; then bootz ${loadaddr} - ${fdt_addr}; else if test ${boot_fdt} = try; then bootz; else echo WARN: Cannot load the DT; fi; fi; else bootz; fi;
|
|
script=boot/boot.scr
|
|
image=boot/zImage
|
|
splashpos=m,m
|