jebbatime
/
micropython
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity

stmhal: Add board files for LIMIFROG board.

gc_dump_improvements
Tobias Badertscher 2016-03-30 11:27:14 +02:00 committed by Damien George
parent 05d1664981
commit 770f169e63
5 changed files with 693 additions and 0 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

68
stmhal/boards/LIMIFROG/mpconfigboard.h 100644
View File

@ -0,0 +1,68 @@
#include STM32_HAL_H
#define MICROPY_HW_BOARD_NAME "LIMIFROG"
#define MICROPY_HW_MCU_NAME "STM32L476"
#define MICROPY_HW_HAS_SWITCH (1)
#define MICROPY_HW_HAS_FLASH (1)
#define MICROPY_HW_HAS_SDCARD (0)
#define MICROPY_HW_HAS_MMA7660 (0)
#define MICROPY_HW_HAS_LIS3DSH (0)
#define MICROPY_HW_HAS_LCD (0)
#define MICROPY_HW_ENABLE_RNG (1)
#define MICROPY_HW_ENABLE_RTC (1)
#define MICROPY_HW_ENABLE_TIMER (1)
#define MICROPY_HW_ENABLE_SERVO (0)
#define MICROPY_HW_ENABLE_DAC (0)
#define MICROPY_HW_ENABLE_CAN (0)
// MSI is used and is 4MHz
#define MICROPY_HW_CLK_PLLM (1)
#define MICROPY_HW_CLK_PLLN (40)
#define MICROPY_HW_CLK_PLLP (RCC_PLLP_DIV7)
#define MICROPY_HW_CLK_PLLR (RCC_PLLR_DIV2)
#define MICROPY_HW_CLK_PLLQ (RCC_PLLQ_DIV2)
#define MICROPY_HW_FLASH_LATENCY FLASH_LATENCY_4
// USART config
#define MICROPY_HW_UART3_PORT (GPIOC)
#define MICROPY_HW_UART3_PINS (GPIO_PIN_10 | GPIO_PIN_11)
// I2C busses
#define MICROPY_HW_I2C1_SCL (pin_B8)
#define MICROPY_HW_I2C1_SDA (pin_B9)
#define MICROPY_HW_I2C2_SCL (pin_B10)
#define MICROPY_HW_I2C2_SDA (pin_B11)
// We use an array of baudrates and corresponding TIMINGR values.
//
// The value 0x90112626 was obtained from the DISCOVERY_I2C1_TIMING constant
// defined in the STM32L4Cube file Drivers/BSP/STM32L476G-Discovery/stm32l476g_discovery.h
#define MICROPY_HW_I2C_BAUDRATE_TIMING {{100000, 0x90112626}}
#define MICROPY_HW_I2C_BAUDRATE_DEFAULT 100000
#define MICROPY_HW_I2C_BAUDRATE_MAX 100000
// SPI busses
#define MICROPY_HW_SPI1_NSS (pin_A4)
#define MICROPY_HW_SPI1_SCK (pin_A5)
#define MICROPY_HW_SPI1_MISO (pin_A6)
#define MICROPY_HW_SPI1_MOSI (pin_A7)
#define MICROPY_HW_SPI3_NSS (pin_A15)
#define MICROPY_HW_SPI3_SCK (pin_B3)
#define MICROPY_HW_SPI3_MISO (pin_B4)
#define MICROPY_HW_SPI3_MOSI (pin_B5)
#define MICROPY_HW_USRSW_PIN (pin_A15)
#define MICROPY_HW_USRSW_PULL (GPIO_NOPULL)
#define MICROPY_HW_USRSW_EXTI_MODE (GPIO_MODE_IT_RISING)
#define MICROPY_HW_USRSW_PRESSED (1)
// LEDs
#define MICROPY_HW_LED1 (pin_C3) // red
#define MICROPY_HW_LED_OTYPE (GPIO_MODE_OUTPUT_PP)
#define MICROPY_HW_LED_ON(pin) (pin->gpio->BSRR = pin->pin_mask)
#define MICROPY_HW_LED_OFF(pin) (pin->gpio->BSRR = pin->pin_mask<<16)
// USB config
// #define MICROPY_HW_USB_OTG_ID_PIN (pin_C12) // This is not the official ID Pin which should be PA10

4
stmhal/boards/LIMIFROG/mpconfigboard.mk 100644
View File

@ -0,0 +1,4 @@
MCU_SERIES = l4
CMSIS_MCU = STM32L476xx
AF_FILE = boards/stm32l476_af.csv
LD_FILE = boards/stm32l476xe.ld

114
stmhal/boards/LIMIFROG/pins.csv 100644
View File

@ -0,0 +1,114 @@
PA0,PA0
PA1,PA1
PA2,PA2
PA3,PA3
PA4,PA4
PA5,PA5
PA6,PA6
PA7,PA7
PA8,PA8
PA9,PA9
PA10,PA10
PA11,PA11
PA12,PA12
PA13,PA13
PA14,PA14
PA15,PA15
PB0,PB0
PB1,PB1
PB2,PB2
PB3,PB3
PB4,PB4
PB5,PB5
PB6,PB6
PB7,PB7
PB8,PB8
PB9,PB9
PB10,PB10
PB11,PB11
PB12,PB12
PB13,PB13
PB14,PB14
PB15,PB15
PC0,PC0
PC1,PC1
PC2,PC2
PC3,PC3
PC4,PC4
PC5,PC5
PC6,PC6
PC7,PC7
PC8,PC8
PC9,PC9
PC10,PC10
PC11,PC11
PC12,PC12
PC13,PC13
PC14,PC14
PC15,PC15
PD0,PD0
PD1,PD1
PD2,PD2
PD3,PD3
PD4,PD4
PD5,PD5
PD6,PD6
PD7,PD7
PD8,PD8
PD9,PD9
PD10,PD10
PD11,PD11
PD12,PD12
PD13,PD13
PD14,PD14
PD15,PD15
PE0,PE0
PE1,PE1
PE2,PE2
PE3,PE3
PE4,PE4
PE5,PE5
PE6,PE6
PE7,PE7
PE8,PE8
PE9,PE9
PE10,PE10
PE11,PE11
PE12,PE12
PE13,PE13
PE14,PE14
PE15,PE15
PF0,PF0
PF1,PF1
PF2,PF2
PF3,PF3
PF4,PF4
PF5,PF5
PF6,PF6
PF7,PF7
PF8,PF8
PF9,PF9
PF10,PF10
PF11,PF11
PF12,PF12
PF13,PF13
PF14,PF14
PF15,PF15
PG0,PG0
PG1,PG1
PG2,PG2
PG3,PG3
PG4,PG4
PG5,PG5
PG6,PG6
PG7,PG7
PG8,PG8
PG9,PG9
PG10,PG10
PG11,PG11
PG12,PG12
PG13,PG13
PG14,PG14
PG15,PG15
PH0,PH0
PH1,PH1
1 PA0 PA0
2 PA1 PA1
3 PA2 PA2
4 PA3 PA3
5 PA4 PA4
6 PA5 PA5
7 PA6 PA6
8 PA7 PA7
9 PA8 PA8
10 PA9 PA9
11 PA10 PA10
12 PA11 PA11
13 PA12 PA12
14 PA13 PA13
15 PA14 PA14
16 PA15 PA15
17 PB0 PB0
18 PB1 PB1
19 PB2 PB2
20 PB3 PB3
21 PB4 PB4
22 PB5 PB5
23 PB6 PB6
24 PB7 PB7
25 PB8 PB8
26 PB9 PB9
27 PB10 PB10
28 PB11 PB11
29 PB12 PB12
30 PB13 PB13
31 PB14 PB14
32 PB15 PB15
33 PC0 PC0
34 PC1 PC1
35 PC2 PC2
36 PC3 PC3
37 PC4 PC4
38 PC5 PC5
39 PC6 PC6
40 PC7 PC7
41 PC8 PC8
42 PC9 PC9
43 PC10 PC10
44 PC11 PC11
45 PC12 PC12
46 PC13 PC13
47 PC14 PC14
48 PC15 PC15
49 PD0 PD0
50 PD1 PD1
51 PD2 PD2
52 PD3 PD3
53 PD4 PD4
54 PD5 PD5
55 PD6 PD6
56 PD7 PD7
57 PD8 PD8
58 PD9 PD9
59 PD10 PD10
60 PD11 PD11
61 PD12 PD12
62 PD13 PD13
63 PD14 PD14
64 PD15 PD15
65 PE0 PE0
66 PE1 PE1
67 PE2 PE2
68 PE3 PE3
69 PE4 PE4
70 PE5 PE5
71 PE6 PE6
72 PE7 PE7
73 PE8 PE8
74 PE9 PE9
75 PE10 PE10
76 PE11 PE11
77 PE12 PE12
78 PE13 PE13
79 PE14 PE14
80 PE15 PE15
81 PF0 PF0
82 PF1 PF1
83 PF2 PF2
84 PF3 PF3
85 PF4 PF4
86 PF5 PF5
87 PF6 PF6
88 PF7 PF7
89 PF8 PF8
90 PF9 PF9
91 PF10 PF10
92 PF11 PF11
93 PF12 PF12
94 PF13 PF13
95 PF14 PF14
96 PF15 PF15
97 PG0 PG0
98 PG1 PG1
99 PG2 PG2
100 PG3 PG3
101 PG4 PG4
102 PG5 PG5
103 PG6 PG6
104 PG7 PG7
105 PG8 PG8
106 PG9 PG9
107 PG10 PG10
108 PG11 PG11
109 PG12 PG12
110 PG13 PG13
111 PG14 PG14
112 PG15 PG15
113 PH0 PH0
114 PH1 PH1

373
stmhal/boards/LIMIFROG/stm32l4xx_hal_conf.h 100644
View File

@ -0,0 +1,373 @@
/**
******************************************************************************
* @file stm32l4xx_hal_conf.h
* @author MCD Application Team
* @version V1.2.0
* @date 25-November-2015
* @brief HAL configuration template file.
* This file should be copied to the application folder and renamed
* to stm32l4xx_hal_conf.h.
******************************************************************************
* @attention
*
* <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32L4xx_HAL_CONF_H
#define __STM32L4xx_HAL_CONF_H
#ifdef __cplusplus
extern "C" {
#endif
#define USE_USB_FS
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/* ########################## Module Selection ############################## */
/**
* @brief This is the list of modules to be used in the HAL driver
*/
#define HAL_MODULE_ENABLED
#define HAL_ADC_MODULE_ENABLED
#define HAL_CAN_MODULE_ENABLED
/* #define HAL_COMP_MODULE_ENABLED */
#define HAL_CORTEX_MODULE_ENABLED
/* #define HAL_CRC_MODULE_ENABLED */
/* #define HAL_CRYP_MODULE_ENABLED */
#define HAL_DAC_MODULE_ENABLED
/* #define HAL_DFSDM_MODULE_ENABLED */
#define HAL_DMA_MODULE_ENABLED
/* #define HAL_FIREWALL_MODULE_ENABLED */
#define HAL_FLASH_MODULE_ENABLED
/* #define HAL_HCD_MODULE_ENABLED */
/* #define HAL_NAND_MODULE_ENABLED */
/* #define HAL_NOR_MODULE_ENABLED */
/* #define HAL_SRAM_MODULE_ENABLED */
#define HAL_GPIO_MODULE_ENABLED
#define HAL_I2C_MODULE_ENABLED
/* #define HAL_IRDA_MODULE_ENABLED */
/* #define HAL_IWDG_MODULE_ENABLED */
/* #define HAL_LCD_MODULE_ENABLED */
/* #define HAL_LPTIM_MODULE_ENABLED */
/* #define HAL_OPAMP_MODULE_ENABLED */
#define HAL_PCD_MODULE_ENABLED
#define HAL_PWR_MODULE_ENABLED
/* #define HAL_QSPI_MODULE_ENABLED */
#define HAL_RCC_MODULE_ENABLED
#define HAL_RNG_MODULE_ENABLED
#define HAL_RTC_MODULE_ENABLED
/* #define HAL_SAI_MODULE_ENABLED */
#define HAL_SD_MODULE_ENABLED
/* #define HAL_SMARTCARD_MODULE_ENABLED */
/* #define HAL_SMBUS_MODULE_ENABLED */
#define HAL_SPI_MODULE_ENABLED
/* #define HAL_SWPMI_MODULE_ENABLED */
#define HAL_TIM_MODULE_ENABLED
/* #define HAL_TSC_MODULE_ENABLED */
#define HAL_UART_MODULE_ENABLED
/* #define HAL_USART_MODULE_ENABLED */
/* #define HAL_WWDG_MODULE_ENABLED */
/* ########################## Oscillator Values adaptation ####################*/
/**
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
* This value is used by the RCC HAL module to compute the system frequency
* (when HSE is used as system clock source, directly or through the PLL).
*/
#if !defined (HSE_VALUE)
#define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
#endif /* HSE_VALUE */
#if !defined (HSE_STARTUP_TIMEOUT)
#define HSE_STARTUP_TIMEOUT ((uint32_t)100) /*!< Time out for HSE start up, in ms */
#endif /* HSE_STARTUP_TIMEOUT */
/**
* @brief Internal Multiple Speed oscillator (MSI) default value.
* This value is the default MSI range value after Reset.
*/
#if !defined (MSI_VALUE)
#define MSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/
#endif /* MSI_VALUE */
/**
* @brief Internal High Speed oscillator (HSI) value.
* This value is used by the RCC HAL module to compute the system frequency
* (when HSI is used as system clock source, directly or through the PLL).
*/
#if !defined (HSI_VALUE)
#define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
#endif /* HSI_VALUE */
/**
* @brief Internal Low Speed oscillator (LSI) value.
*/
#if !defined (LSI_VALUE)
#define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
The real value may vary depending on the variations
in voltage and temperature. */
/**
* @brief External Low Speed oscillator (LSE) value.
* This value is used by the UART, RTC HAL module to compute the system frequency
*/
#if !defined (LSE_VALUE)
#define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/
#endif /* LSE_VALUE */
#if !defined (LSE_STARTUP_TIMEOUT)
#define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */
#endif /* HSE_STARTUP_TIMEOUT */
/**
* @brief External clock source for SAI1 peripheral
* This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source
* frequency.
*/
#if !defined (EXTERNAL_SAI1_CLOCK_VALUE)
#define EXTERNAL_SAI1_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI1 External clock source in Hz*/
#endif /* EXTERNAL_SAI1_CLOCK_VALUE */
/**
* @brief External clock source for SAI2 peripheral
* This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source
* frequency.
*/
#if !defined (EXTERNAL_SAI2_CLOCK_VALUE)
#define EXTERNAL_SAI2_CLOCK_VALUE ((uint32_t)48000) /*!< Value of the SAI2 External clock source in Hz*/
#endif /* EXTERNAL_SAI2_CLOCK_VALUE */
/* Tip: To avoid modifying this file each time you need to use different HSE,
=== you can define the HSE value in your toolchain compiler preprocessor. */
/* ########################### System Configuration ######################### */
/**
* @brief This is the HAL system configuration section
*/
#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
#define TICK_INT_PRIORITY ((uint32_t)0x00) /*!< tick interrupt priority */
#define USE_RTOS 0
#define PREFETCH_ENABLE 1
#define INSTRUCTION_CACHE_ENABLE 1
#define DATA_CACHE_ENABLE 1
/* ########################## Assert Selection ############################## */
/**
* @brief Uncomment the line below to expanse the "assert_param" macro in the
* HAL drivers code
*/
/* #define USE_FULL_ASSERT 1 */
/* Includes ------------------------------------------------------------------*/
/**
* @brief Include module's header file
*/
#ifdef HAL_RCC_MODULE_ENABLED
#include "stm32l4xx_hal_rcc.h"
#endif /* HAL_RCC_MODULE_ENABLED */
#ifdef HAL_GPIO_MODULE_ENABLED
#include "stm32l4xx_hal_gpio.h"
#endif /* HAL_GPIO_MODULE_ENABLED */
#ifdef HAL_DMA_MODULE_ENABLED
#include "stm32l4xx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */
#ifdef HAL_DFSDM_MODULE_ENABLED
#include "stm32l4xx_hal_dfsdm.h"
#endif /* HAL_DFSDM_MODULE_ENABLED */
#ifdef HAL_CORTEX_MODULE_ENABLED
#include "stm32l4xx_hal_cortex.h"
#endif /* HAL_CORTEX_MODULE_ENABLED */
#ifdef HAL_ADC_MODULE_ENABLED
#include "stm32l4xx_hal_adc.h"
#endif /* HAL_ADC_MODULE_ENABLED */
#ifdef HAL_CAN_MODULE_ENABLED
#include "stm32l4xx_hal_can.h"
#endif /* HAL_CAN_MODULE_ENABLED */
#ifdef HAL_COMP_MODULE_ENABLED
#include "stm32l4xx_hal_comp.h"
#endif /* HAL_COMP_MODULE_ENABLED */
#ifdef HAL_CRC_MODULE_ENABLED
#include "stm32l4xx_hal_crc.h"
#endif /* HAL_CRC_MODULE_ENABLED */
#ifdef HAL_CRYP_MODULE_ENABLED
#include "stm32l4xx_hal_cryp.h"
#endif /* HAL_CRYP_MODULE_ENABLED */
#ifdef HAL_DAC_MODULE_ENABLED
#include "stm32l4xx_hal_dac.h"
#endif /* HAL_DAC_MODULE_ENABLED */
#ifdef HAL_FIREWALL_MODULE_ENABLED
#include "stm32l4xx_hal_firewall.h"
#endif /* HAL_FIREWALL_MODULE_ENABLED */
#ifdef HAL_FLASH_MODULE_ENABLED
#include "stm32l4xx_hal_flash.h"
#endif /* HAL_FLASH_MODULE_ENABLED */
#ifdef HAL_SRAM_MODULE_ENABLED
#include "stm32l4xx_hal_sram.h"
#endif /* HAL_SRAM_MODULE_ENABLED */
#ifdef HAL_NOR_MODULE_ENABLED
#include "stm32l4xx_hal_nor.h"
#endif /* HAL_NOR_MODULE_ENABLED */
#ifdef HAL_NAND_MODULE_ENABLED
#include "stm32l4xx_hal_nand.h"
#endif /* HAL_NAND_MODULE_ENABLED */
#ifdef HAL_I2C_MODULE_ENABLED
#include "stm32l4xx_hal_i2c.h"
#endif /* HAL_I2C_MODULE_ENABLED */
#ifdef HAL_IWDG_MODULE_ENABLED
#include "stm32l4xx_hal_iwdg.h"
#endif /* HAL_IWDG_MODULE_ENABLED */
#ifdef HAL_LCD_MODULE_ENABLED
#include "stm32l4xx_hal_lcd.h"
#endif /* HAL_LCD_MODULE_ENABLED */
#ifdef HAL_LPTIM_MODULE_ENABLED
#include "stm32l4xx_hal_lptim.h"
#endif /* HAL_LPTIM_MODULE_ENABLED */
#ifdef HAL_OPAMP_MODULE_ENABLED
#include "stm32l4xx_hal_opamp.h"
#endif /* HAL_OPAMP_MODULE_ENABLED */
#ifdef HAL_PWR_MODULE_ENABLED
#include "stm32l4xx_hal_pwr.h"
#endif /* HAL_PWR_MODULE_ENABLED */
#ifdef HAL_QSPI_MODULE_ENABLED
#include "stm32l4xx_hal_qspi.h"
#endif /* HAL_QSPI_MODULE_ENABLED */
#ifdef HAL_RNG_MODULE_ENABLED
#include "stm32l4xx_hal_rng.h"
#endif /* HAL_RNG_MODULE_ENABLED */
#ifdef HAL_RTC_MODULE_ENABLED
#include "stm32l4xx_hal_rtc.h"
#endif /* HAL_RTC_MODULE_ENABLED */
#ifdef HAL_SAI_MODULE_ENABLED
#include "stm32l4xx_hal_sai.h"
#endif /* HAL_SAI_MODULE_ENABLED */
#ifdef HAL_SD_MODULE_ENABLED
#include "stm32l4xx_hal_sd.h"
#endif /* HAL_SD_MODULE_ENABLED */
#ifdef HAL_SMBUS_MODULE_ENABLED
#include "stm32l4xx_hal_smbus.h"
#endif /* HAL_SMBUS_MODULE_ENABLED */
#ifdef HAL_SPI_MODULE_ENABLED
#include "stm32l4xx_hal_spi.h"
#endif /* HAL_SPI_MODULE_ENABLED */
#ifdef HAL_SWPMI_MODULE_ENABLED
#include "stm32l4xx_hal_swpmi.h"
#endif /* HAL_SWPMI_MODULE_ENABLED */
#ifdef HAL_TIM_MODULE_ENABLED
#include "stm32l4xx_hal_tim.h"
#endif /* HAL_TIM_MODULE_ENABLED */
#ifdef HAL_TSC_MODULE_ENABLED
#include "stm32l4xx_hal_tsc.h"
#endif /* HAL_TSC_MODULE_ENABLED */
#ifdef HAL_UART_MODULE_ENABLED
#include "stm32l4xx_hal_uart.h"
#endif /* HAL_UART_MODULE_ENABLED */
#ifdef HAL_USART_MODULE_ENABLED
#include "stm32l4xx_hal_usart.h"
#endif /* HAL_USART_MODULE_ENABLED */
#ifdef HAL_IRDA_MODULE_ENABLED
#include "stm32l4xx_hal_irda.h"
#endif /* HAL_IRDA_MODULE_ENABLED */
#ifdef HAL_SMARTCARD_MODULE_ENABLED
#include "stm32l4xx_hal_smartcard.h"
#endif /* HAL_SMARTCARD_MODULE_ENABLED */
#ifdef HAL_WWDG_MODULE_ENABLED
#include "stm32l4xx_hal_wwdg.h"
#endif /* HAL_WWDG_MODULE_ENABLED */
#ifdef HAL_PCD_MODULE_ENABLED
#include "stm32l4xx_hal_pcd.h"
#endif /* HAL_PCD_MODULE_ENABLED */
#ifdef HAL_HCD_MODULE_ENABLED
#include "stm32l4xx_hal_hcd.h"
#endif /* HAL_HCD_MODULE_ENABLED */
/* Exported macro ------------------------------------------------------------*/
#ifdef USE_FULL_ASSERT
/**
* @brief The assert_param macro is used for function's parameters check.
* @param expr: If expr is false, it calls assert_failed function
* which reports the name of the source file and the source
* line number of the call that failed.
* If expr is true, it returns no value.
* @retval None
*/
#define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
/* Exported functions ------------------------------------------------------- */
void assert_failed(uint8_t* file, uint32_t line);
#else
#define assert_param(expr) ((void)0)
#endif /* USE_FULL_ASSERT */
#ifdef __cplusplus
}
#endif
#endif /* __STM32L4xx_HAL_CONF_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

134
stmhal/boards/stm32l476xe.ld 100644
View File

@ -0,0 +1,134 @@
/*
GNU linker script for STM32L476XE
*/
/* Specify the memory areas */
MEMORY
{
FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 512K
FLASH_ISR (rx) : ORIGIN = 0x08000000, LENGTH = 0x0000800 /* sector 0, 2 KiB */
FLASH_FS (r) : ORIGIN = 0x08000800, LENGTH = 0x001F800 /* sectors 1-63 (2K each = 126 KiB) */
FLASH_TEXT (rx) : ORIGIN = 0x08020000, LENGTH = 0x0060000 /* Sector starting @ 64 */
RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 96K
SRAM2 (xrw) : ORIGIN = 0x10000000, LENGTH = 32K
}
ENTRY(Reset_Handler)
/* produce a link error if there is not this amount of RAM for these sections */
_minimum_stack_size = 2K;
_minimum_heap_size = 16K;
/* Define the top end of the stack. The stack is full descending so begins just
above last byte of RAM. Note that EABI requires the stack to be 8-byte
aligned for a call. */
_estack = ORIGIN(RAM) + LENGTH(RAM);
/* RAM extents for the garbage collector */
_ram_end = ORIGIN(RAM) + LENGTH(RAM);
_heap_end = 0x20014000; /* tunable */
/* define output sections */
SECTIONS
{
/* The startup code goes first into FLASH */
.isr_vector :
{
. = ALIGN(4);
KEEP(*(.isr_vector)) /* Startup code */
. = ALIGN(4);
} >FLASH_ISR
/* The program code and other data goes into FLASH */
.text :
{
. = ALIGN(4);
*(.text) /* .text sections (code) */
*(.text*) /* .text* sections (code) */
*(.rodata) /* .rodata sections (constants, strings, etc.) */
*(.rodata*) /* .rodata* sections (constants, strings, etc.) */
/* *(.glue_7) */ /* glue arm to thumb code */
/* *(.glue_7t) */ /* glue thumb to arm code */
. = ALIGN(4);
_etext = .; /* define a global symbol at end of code */
} >FLASH_TEXT
/*
.ARM.extab :
{
*(.ARM.extab* .gnu.linkonce.armextab.*)
} >FLASH
.ARM :
{
__exidx_start = .;
*(.ARM.exidx*)
__exidx_end = .;
} >FLASH
*/
/* used by the startup to initialize data */
_sidata = LOADADDR(.data);
/* This is the initialized data section
The program executes knowing that the data is in the RAM
but the loader puts the initial values in the FLASH (inidata).
It is one task of the startup to copy the initial values from FLASH to RAM. */
.data :
{
. = ALIGN(4);
_sdata = .; /* create a global symbol at data start; used by startup code in order to initialise the .data section in RAM */
_ram_start = .; /* create a global symbol at ram start for garbage collector */
*(.data) /* .data sections */
*(.data*) /* .data* sections */
. = ALIGN(4);
_edata = .; /* define a global symbol at data end; used by startup code in order to initialise the .data section in RAM */
} >RAM AT> FLASH_TEXT
/* Uninitialized data section */
.bss :
{
. = ALIGN(4);
_sbss = .; /* define a global symbol at bss start; used by startup code */
*(.bss)
*(.bss*)
*(COMMON)
. = ALIGN(4);
_ebss = .; /* define a global symbol at bss end; used by startup code and GC */
} >RAM
/* this is to define the start of the heap, and make sure we have a minimum size */
.heap :
{
. = ALIGN(4);
PROVIDE ( end = . );
PROVIDE ( _end = . );
_heap_start = .; /* define a global symbol at heap start */
. = . + _minimum_heap_size;
} >RAM
/* this just checks there is enough RAM for the stack */
.stack :
{
. = ALIGN(4);
. = . + _minimum_stack_size;
. = ALIGN(4);
} >RAM
/* Remove information from the standard libraries */
/*
/DISCARD/ :
{
libc.a ( * )
libm.a ( * )
libgcc.a ( * )
}
*/
.ARM.attributes 0 : { *(.ARM.attributes) }
}