And rename SRC_HAL -> HAL_SRC_C and SRC_USBDEV -> USBDEV_SRC_C for
consistency with other source variables.
Follow on from 0fff2e03fe
Signed-off-by: Damien George <damien@micropython.org>
The file `$(BUILD)/firmware.bin` was used by the target `deploy-stlink` and
`deploy-openocd` but it was generated indirectly by the target
`firmware.dfu`.
As this file could be used to program boards directly by a Mass Storage
copy, it's better to make it explicitly generated.
Additionally, some target are refactored to remove redundancy and be more
explicit on dependencies.
Running the update inside the soft-reset loop will mean that (on boards
like PYBD that use a bootloader) the same reset mode is used each
reset loop, eg factory reset occurs each time.
Signed-off-by: Damien George <damien@micropython.org>
The same seed will only occur if the board is the same, the RTC has the
same time (eg freshly powered up) and the first call to this function (eg
via an "import random") is done at exactly the same time since reset.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this commit, the ADC calibration code was never executing because
ADVREGEN bit was set making the CR register always non-zero.
This commit changes the logic so that ADC calibration is always run when
the ADC is disabled and an ADC channel is initialised. It also uses the LL
API functions to do the calibration, to make sure it is done correctly on
each MCU variant.
Signed-off-by: Damien George <damien@micropython.org>
If the device is not connected over USB CDC to a host then all output to
the CDC (eg initial boot messages) is written to the CDC TX buffer with
wrapping, so that the most recent data is retained when the USB CDC is
eventually connected (eg so the REPL banner is displayed upon connection).
This commit fixes a bug in this behaviour, which was likely introduced in
e4fcd216e0, where the initial data in the CDC
TX buffer is repeated multiple times on first connection of the device to
the host.
Signed-off-by: Damien George <damien@micropython.org>
When installing WS firmware, the very first GET_STATE can take several
seconds to respond (especially with the larger binaries like
BLE_stack_full).
Allows stm.rfcore_sys_hci to take an optional timeout, defaulting to
SYS_ACK_TIMEOUT_MS (which is 250ms).
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
The flash can sometimes be in an already-unlocked state, and attempting to
unlock it again will cause an immediate reset. So make _Flash.unlock()
check FLASH_CR_LOCK to get the current state.
Also fix some magic numbers for FLASH_CR_LOCK AND FLASH_CR_STRT.
The machine.reset() could be removed because it no longer crashes now that
the flash unlock is fixed.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit adds a script that can be run on-device to install FUS and WS
binaries from the filesystem. Instructions for use are provided in
the rfcore_firmware.py file.
The commit also removes unneeded functionality from the existing rfcore.py
debug script (and renames it rfcore_debug.py).
The new functions provide FUS/WS status, version and SYS HCI commands:
- stm.rfcore_status()
- stm.rfcore_fw_version(fw_id)
- stm.rfcore_sys_hci(ogf, ocf, cmd)
Changes are:
- Fix missing IRQ handler when SDMMC2 is used instead of SDMMC1 with H7
MCUs.
- Removed outdated H7 series compatibility macros.
- Defined common IRQ handler macro for F4 series.
It requires mp_hal_time_ns() to be provided by a port. This function
allows very accurate absolute timestamps.
Enabled on unix, windows, stm32, esp8266 and esp32.
Signed-off-by: Damien George <damien@micropython.org>
With a warning that this way of constructing software I2C/SPI is
deprecated. The check and warning will be removed in a future release.
This should help existing code to migrate to the new SoftI2C/SoftSPI types.
Signed-off-by: Damien George <damien@micropython.org>
Previous commits removed the ability for one I2C/SPI constructor to
construct both software- or hardware-based peripheral instances. Such
construction is now split to explicit soft and non-soft types.
This commit makes both types available in all ports that previously could
create both software and hardware peripherals: machine.I2C and machine.SPI
construct hardware instances, while machine.SoftI2C and machine.SoftSPI
create software instances.
This is a breaking change for use of software-based I2C and SPI. Code that
constructed I2C/SPI peripherals in the following way will need to be
changed:
machine.I2C(-1, ...) -> machine.SoftI2C(...)
machine.I2C(scl=scl, sda=sda) -> machine.SoftI2C(scl=scl, sda=sda)
machine.SPI(-1, ...) -> machine.SoftSPI(...)
machine.SPI(sck=sck, mosi=mosi, miso=miso)
-> machine.SoftSPI(sck=sck, mosi=mosi, miso=miso)
Code which uses machine.I2C and machine.SPI classes to access hardware
peripherals does not need to change.
Signed-off-by: Damien George <damien@micropython.org>
The SoftSPI constructor is now used soley to create SoftSPI instances, it
can no longer delegate to create a hardware-based SPI instance.
Signed-off-by: Damien George <damien@micropython.org>
The SoftI2C constructor is now used soley to create SoftI2C instances, it
can no longer delegate to create a hardware-based I2C instance.
Signed-off-by: Damien George <damien@micropython.org>
Also rename machine_i2c_type to mp_machine_soft_i2c_type. These changes
make it clear that it's a soft-I2C implementation, and match SoftSPI.
Signed-off-by: Damien George <damien@micropython.org>
The device info table has a different layout when core 2 is in FUS mode.
In particular it's larger than the 32 bytes used when in WS mode and if the
correct amount of space is not allocated then the end of the table may be
overwritten with other data (eg with FUS version 0.5.3). So update the
structure to fix this.
Also update rfcore.py to disable IRQs (which are enabled by rfcore.c), to
not depend on uctypes, and to not require the asm_thumb emitter.
Signed-off-by: Damien George <damien@micropython.org>
For time-based functions that work with absolute time there is the need for
an Epoch, to set the zero-point at which the absolute time starts counting.
Such functions include time.time() and filesystem stat return values. And
different ports may use a different Epoch.
To make it clearer what functions use the Epoch (whatever it may be), and
make the ports more consistent with their use of the Epoch, this commit
renames all Epoch related functions to include the word "epoch" in their
name (and remove references to "2000").
Along with this rename, the following things have changed:
- mp_hal_time_ns() is now specified to return the number of nanoseconds
since the Epoch, rather than since 1970 (but since this is an internal
function it doesn't change anything for the user).
- littlefs timestamps on the esp8266 have been fixed (they were previously
off by 30 years in nanoseconds).
Otherwise, there is no functional change made by this commit.
Signed-off-by: Damien George <damien@micropython.org>
To portably get the Epoch. This is simply aliased to localtime() on ports
that are not timezone aware.
Signed-off-by: Damien George <damien@micropython.org>
This allows prototyping rfcore.c improvements from Python.
This was mostly written by @dpgeorge with small modifications to work after
rfcore_init() by @jimmo.
Before this change there was up to a 128ms delay on incoming payloads from
CPU2 as it was polled by SysTick. Now the RX IRQ immediately schedules the
PendSV.
This is required to allow using WS firmware newer than 1.1.1 concurrently
with USB (e.g. USB VCP). It prevents CPU2 from modifying the CLK48 config
on boot.
Tested on WS=1.8 FUS=1.1.
See AN5289 and https://github.com/micropython/micropython/issues/6316
- Split tables and buffers into SRAM2A/2B.
- Use structs rather than word offsets to access tables.
- Use FLASH_IPCCDBA register value rather than option bytes directly.
Previously the interaction between the different layers of the Bluetooth
stack was different on each port and each stack. This commit defines
common interfaces between them and implements them for cyw43, btstack,
nimble, stm32, unix.
mp_irq_init() is useful when the IRQ object is allocated by the caller.
The mp_irq_methods_t.init method is not used anywhere so has been removed.
Signed-off-by: Damien George <damien@micropython.org>
Updating to Black v20.8b1 there are two changes that affect the code in
this repository:
- If there is a trailing comma in a list (eg [], () or function call) then
that list is now written out with one line per element. So remove such
trailing commas where the list should stay on one line.
- Spaces at the start of """ doc strings are removed.
Signed-off-by: Damien George <damien@micropython.org>
Damien George