1
0
Fork 0
alistair23-linux/drivers/leds/leds-lp55xx-common.c

594 lines
13 KiB
C
Raw Permalink Normal View History

// SPDX-License-Identifier: GPL-2.0-only
/*
* LP5521/LP5523/LP55231/LP5562 Common Driver
*
* Copyright 2012 Texas Instruments
*
* Author: Milo(Woogyom) Kim <milo.kim@ti.com>
*
* Derived from leds-lp5521.c, leds-lp5523.c
*/
#include <linux/clk.h>
#include <linux/delay.h>
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
#include <linux/firmware.h>
#include <linux/i2c.h>
#include <linux/leds.h>
#include <linux/module.h>
#include <linux/platform_data/leds-lp55xx.h>
#include <linux/slab.h>
#include <linux/gpio.h>
#include <linux/of_gpio.h>
#include "leds-lp55xx-common.h"
/* External clock rate */
#define LP55XX_CLK_32K 32768
static struct lp55xx_led *cdev_to_lp55xx_led(struct led_classdev *cdev)
{
return container_of(cdev, struct lp55xx_led, cdev);
}
static struct lp55xx_led *dev_to_lp55xx_led(struct device *dev)
{
return cdev_to_lp55xx_led(dev_get_drvdata(dev));
}
static void lp55xx_reset_device(struct lp55xx_chip *chip)
{
struct lp55xx_device_config *cfg = chip->cfg;
u8 addr = cfg->reset.addr;
u8 val = cfg->reset.val;
/* no error checking here because no ACK from the device after reset */
lp55xx_write(chip, addr, val);
}
static int lp55xx_detect_device(struct lp55xx_chip *chip)
{
struct lp55xx_device_config *cfg = chip->cfg;
u8 addr = cfg->enable.addr;
u8 val = cfg->enable.val;
int ret;
ret = lp55xx_write(chip, addr, val);
if (ret)
return ret;
usleep_range(1000, 2000);
ret = lp55xx_read(chip, addr, &val);
if (ret)
return ret;
if (val != cfg->enable.val)
return -ENODEV;
return 0;
}
static int lp55xx_post_init_device(struct lp55xx_chip *chip)
{
struct lp55xx_device_config *cfg = chip->cfg;
if (!cfg->post_init_device)
return 0;
return cfg->post_init_device(chip);
}
static ssize_t lp55xx_show_current(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct lp55xx_led *led = dev_to_lp55xx_led(dev);
return scnprintf(buf, PAGE_SIZE, "%d\n", led->led_current);
}
static ssize_t lp55xx_store_current(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct lp55xx_led *led = dev_to_lp55xx_led(dev);
struct lp55xx_chip *chip = led->chip;
unsigned long curr;
if (kstrtoul(buf, 0, &curr))
return -EINVAL;
if (curr > led->max_current)
return -EINVAL;
if (!chip->cfg->set_led_current)
return len;
mutex_lock(&chip->lock);
chip->cfg->set_led_current(led, (u8)curr);
mutex_unlock(&chip->lock);
return len;
}
static ssize_t lp55xx_show_max_current(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct lp55xx_led *led = dev_to_lp55xx_led(dev);
return scnprintf(buf, PAGE_SIZE, "%d\n", led->max_current);
}
static DEVICE_ATTR(led_current, S_IRUGO | S_IWUSR, lp55xx_show_current,
lp55xx_store_current);
static DEVICE_ATTR(max_current, S_IRUGO , lp55xx_show_max_current, NULL);
static struct attribute *lp55xx_led_attrs[] = {
&dev_attr_led_current.attr,
&dev_attr_max_current.attr,
NULL,
};
ATTRIBUTE_GROUPS(lp55xx_led);
static int lp55xx_set_brightness(struct led_classdev *cdev,
enum led_brightness brightness)
{
struct lp55xx_led *led = cdev_to_lp55xx_led(cdev);
struct lp55xx_device_config *cfg = led->chip->cfg;
led->brightness = (u8)brightness;
return cfg->brightness_fn(led);
}
static int lp55xx_init_led(struct lp55xx_led *led,
struct lp55xx_chip *chip, int chan)
{
struct lp55xx_platform_data *pdata = chip->pdata;
struct lp55xx_device_config *cfg = chip->cfg;
struct device *dev = &chip->cl->dev;
char name[32];
int ret;
int max_channel = cfg->max_channel;
if (chan >= max_channel) {
dev_err(dev, "invalid channel: %d / %d\n", chan, max_channel);
return -EINVAL;
}
if (pdata->led_config[chan].led_current == 0)
return 0;
led->led_current = pdata->led_config[chan].led_current;
led->max_current = pdata->led_config[chan].max_current;
led->chan_nr = pdata->led_config[chan].chan_nr;
led->cdev.default_trigger = pdata->led_config[chan].default_trigger;
if (led->chan_nr >= max_channel) {
dev_err(dev, "Use channel numbers between 0 and %d\n",
max_channel - 1);
return -EINVAL;
}
led->cdev.brightness_set_blocking = lp55xx_set_brightness;
led->cdev.groups = lp55xx_led_groups;
if (pdata->led_config[chan].name) {
led->cdev.name = pdata->led_config[chan].name;
} else {
snprintf(name, sizeof(name), "%s:channel%d",
pdata->label ? : chip->cl->name, chan);
led->cdev.name = name;
}
ret = led_classdev_register(dev, &led->cdev);
if (ret) {
dev_err(dev, "led register err: %d\n", ret);
return ret;
}
return 0;
}
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
static void lp55xx_firmware_loaded(const struct firmware *fw, void *context)
{
struct lp55xx_chip *chip = context;
struct device *dev = &chip->cl->dev;
enum lp55xx_engine_index idx = chip->engine_idx;
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
if (!fw) {
dev_err(dev, "firmware request failed\n");
return;
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
}
/* handling firmware data is chip dependent */
mutex_lock(&chip->lock);
chip->engines[idx - 1].mode = LP55XX_ENGINE_LOAD;
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
chip->fw = fw;
if (chip->cfg->firmware_cb)
chip->cfg->firmware_cb(chip);
mutex_unlock(&chip->lock);
/* firmware should be released for other channel use */
release_firmware(chip->fw);
chip->fw = NULL;
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
}
static int lp55xx_request_firmware(struct lp55xx_chip *chip)
{
const char *name = chip->cl->name;
struct device *dev = &chip->cl->dev;
leds:lp55xx: fix firmware loading error LP55xx driver uses not firmware file but raw data to load program through the firmware interface.(Documents/leds/leds-lp55xx.txt) For example, here is how to run blinking green channel pattern. (The second engine is seleted and MUX is mapped to 'RGB' mode) echo 2 > /sys/bus/i2c/devices/xxxx/select_engine echo "RGB" > /sys/bus/i2c/devices/xxxx/engine_mux echo 1 > /sys/class/firmware/lp5562/loading echo "4000600040FF6000" > /sys/class/firmware/lp5562/data echo 0 > /sys/class/firmware/lp5562/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine However, '/sys/class/firmware/<device name>' is not created after the firmware loader user helper was introduced. This feature is used in the case below. As soon as the firmware download is requested by the driver, firmware class subsystem tries to find the binary file. If it gets failed, then it just falls back to user helper to load raw data manually. Here, you can see the device file under /sys/class/firmware/. To make it happen, LP55xx driver requires two configurations. 1. Enable CONFIG_FW_LOADER_USER_HELPER_FALLBACK in Kconfig 2. Set option, 'FW_OPT_USERHELPER' on requesting the firmware data. It means the second option should be 'false' in request_firmware_nowait(). This option enables to load firmware data manually by calling fw_load_from_user_helper(). Cc: linux-leds@vger.kernel.org Signed-off-by: Milo Kim <milo.kim@ti.com> Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2015-06-28 18:39:14 -06:00
return request_firmware_nowait(THIS_MODULE, false, name, dev,
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
GFP_KERNEL, chip, lp55xx_firmware_loaded);
}
static ssize_t lp55xx_show_engine_select(struct device *dev,
struct device_attribute *attr,
char *buf)
{
struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
struct lp55xx_chip *chip = led->chip;
return sprintf(buf, "%d\n", chip->engine_idx);
}
static ssize_t lp55xx_store_engine_select(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
struct lp55xx_chip *chip = led->chip;
unsigned long val;
int ret;
if (kstrtoul(buf, 0, &val))
return -EINVAL;
/* select the engine to be run */
switch (val) {
case LP55XX_ENGINE_1:
case LP55XX_ENGINE_2:
case LP55XX_ENGINE_3:
mutex_lock(&chip->lock);
chip->engine_idx = val;
ret = lp55xx_request_firmware(chip);
mutex_unlock(&chip->lock);
break;
default:
dev_err(dev, "%lu: invalid engine index. (1, 2, 3)\n", val);
return -EINVAL;
}
if (ret) {
dev_err(dev, "request firmware err: %d\n", ret);
return ret;
}
return len;
}
static inline void lp55xx_run_engine(struct lp55xx_chip *chip, bool start)
{
if (chip->cfg->run_engine)
chip->cfg->run_engine(chip, start);
}
static ssize_t lp55xx_store_engine_run(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t len)
{
struct lp55xx_led *led = i2c_get_clientdata(to_i2c_client(dev));
struct lp55xx_chip *chip = led->chip;
unsigned long val;
if (kstrtoul(buf, 0, &val))
return -EINVAL;
/* run or stop the selected engine */
if (val <= 0) {
lp55xx_run_engine(chip, false);
return len;
}
mutex_lock(&chip->lock);
lp55xx_run_engine(chip, true);
mutex_unlock(&chip->lock);
return len;
}
static DEVICE_ATTR(select_engine, S_IRUGO | S_IWUSR,
lp55xx_show_engine_select, lp55xx_store_engine_select);
static DEVICE_ATTR(run_engine, S_IWUSR, NULL, lp55xx_store_engine_run);
static struct attribute *lp55xx_engine_attributes[] = {
leds-lp55xx: support firmware interface This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-05 03:17:20 -07:00
&dev_attr_select_engine.attr,
&dev_attr_run_engine.attr,
NULL,
};
static const struct attribute_group lp55xx_engine_attr_group = {
.attrs = lp55xx_engine_attributes,
};
int lp55xx_write(struct lp55xx_chip *chip, u8 reg, u8 val)
{
return i2c_smbus_write_byte_data(chip->cl, reg, val);
}
EXPORT_SYMBOL_GPL(lp55xx_write);
int lp55xx_read(struct lp55xx_chip *chip, u8 reg, u8 *val)
{
s32 ret;
ret = i2c_smbus_read_byte_data(chip->cl, reg);
if (ret < 0)
return ret;
*val = ret;
return 0;
}
EXPORT_SYMBOL_GPL(lp55xx_read);
int lp55xx_update_bits(struct lp55xx_chip *chip, u8 reg, u8 mask, u8 val)
{
int ret;
u8 tmp;
ret = lp55xx_read(chip, reg, &tmp);
if (ret)
return ret;
tmp &= ~mask;
tmp |= val & mask;
return lp55xx_write(chip, reg, tmp);
}
EXPORT_SYMBOL_GPL(lp55xx_update_bits);
bool lp55xx_is_extclk_used(struct lp55xx_chip *chip)
{
struct clk *clk;
int err;
clk = devm_clk_get(&chip->cl->dev, "32k_clk");
if (IS_ERR(clk))
goto use_internal_clk;
err = clk_prepare_enable(clk);
if (err)
goto use_internal_clk;
if (clk_get_rate(clk) != LP55XX_CLK_32K) {
clk_disable_unprepare(clk);
goto use_internal_clk;
}
dev_info(&chip->cl->dev, "%dHz external clock used\n", LP55XX_CLK_32K);
chip->clk = clk;
return true;
use_internal_clk:
dev_info(&chip->cl->dev, "internal clock used\n");
return false;
}
EXPORT_SYMBOL_GPL(lp55xx_is_extclk_used);
int lp55xx_init_device(struct lp55xx_chip *chip)
{
struct lp55xx_platform_data *pdata;
struct lp55xx_device_config *cfg;
struct device *dev = &chip->cl->dev;
int ret = 0;
WARN_ON(!chip);
pdata = chip->pdata;
cfg = chip->cfg;
if (!pdata || !cfg)
return -EINVAL;
if (gpio_is_valid(pdata->enable_gpio)) {
ret = devm_gpio_request_one(dev, pdata->enable_gpio,
GPIOF_DIR_OUT, "lp5523_enable");
if (ret < 0) {
dev_err(dev, "could not acquire enable gpio (err=%d)\n",
ret);
goto err;
}
gpio_set_value(pdata->enable_gpio, 0);
usleep_range(1000, 2000); /* Keep enable down at least 1ms */
gpio_set_value(pdata->enable_gpio, 1);
usleep_range(1000, 2000); /* 500us abs min. */
}
lp55xx_reset_device(chip);
/*
* Exact value is not available. 10 - 20ms
* appears to be enough for reset.
*/
usleep_range(10000, 20000);
ret = lp55xx_detect_device(chip);
if (ret) {
dev_err(dev, "device detection err: %d\n", ret);
goto err;
}
/* chip specific initialization */
ret = lp55xx_post_init_device(chip);
if (ret) {
dev_err(dev, "post init device err: %d\n", ret);
goto err_post_init;
}
return 0;
err_post_init:
lp55xx_deinit_device(chip);
err:
return ret;
}
EXPORT_SYMBOL_GPL(lp55xx_init_device);
void lp55xx_deinit_device(struct lp55xx_chip *chip)
{
struct lp55xx_platform_data *pdata = chip->pdata;
if (chip->clk)
clk_disable_unprepare(chip->clk);
if (gpio_is_valid(pdata->enable_gpio))
gpio_set_value(pdata->enable_gpio, 0);
}
EXPORT_SYMBOL_GPL(lp55xx_deinit_device);
int lp55xx_register_leds(struct lp55xx_led *led, struct lp55xx_chip *chip)
{
struct lp55xx_platform_data *pdata = chip->pdata;
struct lp55xx_device_config *cfg = chip->cfg;
int num_channels = pdata->num_channels;
struct lp55xx_led *each;
u8 led_current;
int ret;
int i;
if (!cfg->brightness_fn) {
dev_err(&chip->cl->dev, "empty brightness configuration\n");
return -EINVAL;
}
for (i = 0; i < num_channels; i++) {
/* do not initialize channels that are not connected */
if (pdata->led_config[i].led_current == 0)
continue;
led_current = pdata->led_config[i].led_current;
each = led + i;
ret = lp55xx_init_led(each, chip, i);
if (ret)
goto err_init_led;
chip->num_leds++;
each->chip = chip;
/* setting led current at each channel */
if (cfg->set_led_current)
cfg->set_led_current(each, led_current);
}
return 0;
err_init_led:
lp55xx_unregister_leds(led, chip);
return ret;
}
EXPORT_SYMBOL_GPL(lp55xx_register_leds);
void lp55xx_unregister_leds(struct lp55xx_led *led, struct lp55xx_chip *chip)
{
int i;
struct lp55xx_led *each;
for (i = 0; i < chip->num_leds; i++) {
each = led + i;
led_classdev_unregister(&each->cdev);
}
}
EXPORT_SYMBOL_GPL(lp55xx_unregister_leds);
int lp55xx_register_sysfs(struct lp55xx_chip *chip)
{
struct device *dev = &chip->cl->dev;
struct lp55xx_device_config *cfg = chip->cfg;
int ret;
if (!cfg->run_engine || !cfg->firmware_cb)
goto dev_specific_attrs;
ret = sysfs_create_group(&dev->kobj, &lp55xx_engine_attr_group);
if (ret)
return ret;
dev_specific_attrs:
return cfg->dev_attr_group ?
sysfs_create_group(&dev->kobj, cfg->dev_attr_group) : 0;
}
EXPORT_SYMBOL_GPL(lp55xx_register_sysfs);
void lp55xx_unregister_sysfs(struct lp55xx_chip *chip)
{
struct device *dev = &chip->cl->dev;
struct lp55xx_device_config *cfg = chip->cfg;
if (cfg->dev_attr_group)
sysfs_remove_group(&dev->kobj, cfg->dev_attr_group);
sysfs_remove_group(&dev->kobj, &lp55xx_engine_attr_group);
}
EXPORT_SYMBOL_GPL(lp55xx_unregister_sysfs);
struct lp55xx_platform_data *lp55xx_of_populate_pdata(struct device *dev,
struct device_node *np)
{
struct device_node *child;
struct lp55xx_platform_data *pdata;
struct lp55xx_led_config *cfg;
int num_channels;
int i = 0;
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return ERR_PTR(-ENOMEM);
num_channels = of_get_child_count(np);
if (num_channels == 0) {
dev_err(dev, "no LED channels\n");
return ERR_PTR(-EINVAL);
}
treewide: devm_kzalloc() -> devm_kcalloc() The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc(). This patch replaces cases of: devm_kzalloc(handle, a * b, gfp) with: devm_kcalloc(handle, a * b, gfp) as well as handling cases of: devm_kzalloc(handle, a * b * c, gfp) with: devm_kzalloc(handle, array3_size(a, b, c), gfp) as it's slightly less ugly than: devm_kcalloc(handle, array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: devm_kzalloc(handle, 4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. Some manual whitespace fixes were needed in this patch, as Coccinelle really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...". The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ expression HANDLE; type TYPE; expression THING, E; @@ ( devm_kzalloc(HANDLE, - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | devm_kzalloc(HANDLE, - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression HANDLE; expression COUNT; typedef u8; typedef __u8; @@ ( devm_kzalloc(HANDLE, - sizeof(u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * (COUNT) + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(__u8) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(char) * COUNT + COUNT , ...) | devm_kzalloc(HANDLE, - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ expression HANDLE; type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ expression HANDLE; identifier SIZE, COUNT; @@ - devm_kzalloc + devm_kcalloc (HANDLE, - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression HANDLE; expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression HANDLE; expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | devm_kzalloc(HANDLE, - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ expression HANDLE; identifier STRIDE, SIZE, COUNT; @@ ( devm_kzalloc(HANDLE, - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | devm_kzalloc(HANDLE, - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression HANDLE; expression E1, E2, E3; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | devm_kzalloc(HANDLE, - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression HANDLE; expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( devm_kzalloc(HANDLE, sizeof(THING) * C2, ...) | devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...) | devm_kzalloc(HANDLE, C1 * C2 * C3, ...) | devm_kzalloc(HANDLE, C1 * C2, ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * E2 + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - (E1) * (E2) + E1, E2 , ...) | - devm_kzalloc + devm_kcalloc (HANDLE, - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-06-12 15:07:58 -06:00
cfg = devm_kcalloc(dev, num_channels, sizeof(*cfg), GFP_KERNEL);
if (!cfg)
return ERR_PTR(-ENOMEM);
pdata->led_config = &cfg[0];
pdata->num_channels = num_channels;
for_each_child_of_node(np, child) {
cfg[i].chan_nr = i;
of_property_read_string(child, "chan-name", &cfg[i].name);
of_property_read_u8(child, "led-cur", &cfg[i].led_current);
of_property_read_u8(child, "max-cur", &cfg[i].max_current);
cfg[i].default_trigger =
of_get_property(child, "linux,default-trigger", NULL);
i++;
}
of_property_read_string(np, "label", &pdata->label);
of_property_read_u8(np, "clock-mode", &pdata->clock_mode);
pdata->enable_gpio = of_get_named_gpio(np, "enable-gpio", 0);
/* LP8501 specific */
of_property_read_u8(np, "pwr-sel", (u8 *)&pdata->pwr_sel);
return pdata;
}
EXPORT_SYMBOL_GPL(lp55xx_of_populate_pdata);
MODULE_AUTHOR("Milo Kim <milo.kim@ti.com>");
MODULE_DESCRIPTION("LP55xx Common Driver");
MODULE_LICENSE("GPL");