2018-04-16 21:43:36 -06:00
|
|
|
// SPDX-License-Identifier: GPL-2.0
|
|
|
|
/*
|
|
|
|
* Lattice MachXO2 Slave SPI Driver
|
|
|
|
*
|
|
|
|
* Manage Lattice FPGA firmware that is loaded over SPI using
|
|
|
|
* the slave serial configuration interface.
|
|
|
|
*
|
|
|
|
* Copyright (C) 2018 Paolo Pisati <p.pisati@gmail.com>
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <linux/delay.h>
|
|
|
|
#include <linux/fpga/fpga-mgr.h>
|
|
|
|
#include <linux/gpio/consumer.h>
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/of.h>
|
|
|
|
#include <linux/spi/spi.h>
|
|
|
|
|
|
|
|
/* MachXO2 Programming Guide - sysCONFIG Programming Commands */
|
|
|
|
#define IDCODE_PUB {0xe0, 0x00, 0x00, 0x00}
|
|
|
|
#define ISC_ENABLE {0xc6, 0x08, 0x00, 0x00}
|
|
|
|
#define ISC_ERASE {0x0e, 0x04, 0x00, 0x00}
|
|
|
|
#define ISC_PROGRAMDONE {0x5e, 0x00, 0x00, 0x00}
|
|
|
|
#define LSC_INITADDRESS {0x46, 0x00, 0x00, 0x00}
|
|
|
|
#define LSC_PROGINCRNV {0x70, 0x00, 0x00, 0x01}
|
|
|
|
#define LSC_READ_STATUS {0x3c, 0x00, 0x00, 0x00}
|
|
|
|
#define LSC_REFRESH {0x79, 0x00, 0x00, 0x00}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Max CCLK in Slave SPI mode according to 'MachXO2 Family Data
|
|
|
|
* Sheet' sysCONFIG Port Timing Specifications (3-36)
|
|
|
|
*/
|
|
|
|
#define MACHXO2_MAX_SPEED 66000000
|
|
|
|
|
|
|
|
#define MACHXO2_LOW_DELAY_USEC 5
|
|
|
|
#define MACHXO2_HIGH_DELAY_USEC 200
|
|
|
|
#define MACHXO2_REFRESH_USEC 4800
|
|
|
|
#define MACHXO2_MAX_BUSY_LOOP 128
|
|
|
|
#define MACHXO2_MAX_REFRESH_LOOP 16
|
|
|
|
|
|
|
|
#define MACHXO2_PAGE_SIZE 16
|
|
|
|
#define MACHXO2_BUF_SIZE (MACHXO2_PAGE_SIZE + 4)
|
|
|
|
|
|
|
|
/* Status register bits, errors and error mask */
|
|
|
|
#define BUSY 12
|
|
|
|
#define DONE 8
|
|
|
|
#define DVER 27
|
|
|
|
#define ENAB 9
|
|
|
|
#define ERRBITS 23
|
|
|
|
#define ERRMASK 7
|
|
|
|
#define FAIL 13
|
|
|
|
|
|
|
|
#define ENOERR 0 /* no error */
|
|
|
|
#define EID 1
|
|
|
|
#define ECMD 2
|
|
|
|
#define ECRC 3
|
|
|
|
#define EPREAM 4 /* preamble error */
|
|
|
|
#define EABRT 5 /* abort error */
|
|
|
|
#define EOVERFL 6 /* overflow error */
|
|
|
|
#define ESDMEOF 7 /* SDM EOF */
|
|
|
|
|
|
|
|
static inline u8 get_err(unsigned long *status)
|
|
|
|
{
|
|
|
|
return (*status >> ERRBITS) & ERRMASK;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int get_status(struct spi_device *spi, unsigned long *status)
|
|
|
|
{
|
|
|
|
struct spi_message msg;
|
|
|
|
struct spi_transfer rx, tx;
|
|
|
|
static const u8 cmd[] = LSC_READ_STATUS;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
memset(&rx, 0, sizeof(rx));
|
|
|
|
memset(&tx, 0, sizeof(tx));
|
|
|
|
tx.tx_buf = cmd;
|
|
|
|
tx.len = sizeof(cmd);
|
|
|
|
rx.rx_buf = status;
|
|
|
|
rx.len = 4;
|
|
|
|
spi_message_init(&msg);
|
|
|
|
spi_message_add_tail(&tx, &msg);
|
|
|
|
spi_message_add_tail(&rx, &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
return ret;
|
|
|
|
|
|
|
|
*status = be32_to_cpu(*status);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
#ifdef DEBUG
|
|
|
|
static const char *get_err_string(u8 err)
|
|
|
|
{
|
|
|
|
switch (err) {
|
|
|
|
case ENOERR: return "No Error";
|
|
|
|
case EID: return "ID ERR";
|
|
|
|
case ECMD: return "CMD ERR";
|
|
|
|
case ECRC: return "CRC ERR";
|
|
|
|
case EPREAM: return "Preamble ERR";
|
|
|
|
case EABRT: return "Abort ERR";
|
|
|
|
case EOVERFL: return "Overflow ERR";
|
|
|
|
case ESDMEOF: return "SDM EOF";
|
|
|
|
}
|
|
|
|
|
|
|
|
return "Default switch case";
|
|
|
|
}
|
|
|
|
#endif
|
|
|
|
|
|
|
|
static void dump_status_reg(unsigned long *status)
|
|
|
|
{
|
|
|
|
#ifdef DEBUG
|
|
|
|
pr_debug("machxo2 status: 0x%08lX - done=%d, cfgena=%d, busy=%d, fail=%d, devver=%d, err=%s\n",
|
|
|
|
*status, test_bit(DONE, status), test_bit(ENAB, status),
|
|
|
|
test_bit(BUSY, status), test_bit(FAIL, status),
|
|
|
|
test_bit(DVER, status), get_err_string(get_err(status)));
|
|
|
|
#endif
|
|
|
|
}
|
|
|
|
|
|
|
|
static int wait_until_not_busy(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
unsigned long status;
|
|
|
|
int ret, loop = 0;
|
|
|
|
|
|
|
|
do {
|
|
|
|
ret = get_status(spi, &status);
|
|
|
|
if (ret)
|
|
|
|
return ret;
|
|
|
|
if (++loop >= MACHXO2_MAX_BUSY_LOOP)
|
|
|
|
return -EBUSY;
|
|
|
|
} while (test_bit(BUSY, &status));
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int machxo2_cleanup(struct fpga_manager *mgr)
|
|
|
|
{
|
|
|
|
struct spi_device *spi = mgr->priv;
|
|
|
|
struct spi_message msg;
|
|
|
|
struct spi_transfer tx[2];
|
|
|
|
static const u8 erase[] = ISC_ERASE;
|
|
|
|
static const u8 refresh[] = LSC_REFRESH;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
memset(tx, 0, sizeof(tx));
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx[0].tx_buf = &erase;
|
|
|
|
tx[0].len = sizeof(erase);
|
|
|
|
spi_message_add_tail(&tx[0], &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
ret = wait_until_not_busy(spi);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx[1].tx_buf = &refresh;
|
|
|
|
tx[1].len = sizeof(refresh);
|
|
|
|
tx[1].delay_usecs = MACHXO2_REFRESH_USEC;
|
|
|
|
spi_message_add_tail(&tx[1], &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
fail:
|
|
|
|
dev_err(&mgr->dev, "Cleanup failed\n");
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static enum fpga_mgr_states machxo2_spi_state(struct fpga_manager *mgr)
|
|
|
|
{
|
|
|
|
struct spi_device *spi = mgr->priv;
|
|
|
|
unsigned long status;
|
|
|
|
|
|
|
|
get_status(spi, &status);
|
|
|
|
if (!test_bit(BUSY, &status) && test_bit(DONE, &status) &&
|
|
|
|
get_err(&status) == ENOERR)
|
|
|
|
return FPGA_MGR_STATE_OPERATING;
|
|
|
|
|
|
|
|
return FPGA_MGR_STATE_UNKNOWN;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int machxo2_write_init(struct fpga_manager *mgr,
|
|
|
|
struct fpga_image_info *info,
|
|
|
|
const char *buf, size_t count)
|
|
|
|
{
|
|
|
|
struct spi_device *spi = mgr->priv;
|
|
|
|
struct spi_message msg;
|
|
|
|
struct spi_transfer tx[3];
|
|
|
|
static const u8 enable[] = ISC_ENABLE;
|
|
|
|
static const u8 erase[] = ISC_ERASE;
|
|
|
|
static const u8 initaddr[] = LSC_INITADDRESS;
|
|
|
|
unsigned long status;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
if ((info->flags & FPGA_MGR_PARTIAL_RECONFIG)) {
|
|
|
|
dev_err(&mgr->dev,
|
|
|
|
"Partial reconfiguration is not supported\n");
|
|
|
|
return -ENOTSUPP;
|
|
|
|
}
|
|
|
|
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
memset(tx, 0, sizeof(tx));
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx[0].tx_buf = &enable;
|
|
|
|
tx[0].len = sizeof(enable);
|
|
|
|
tx[0].delay_usecs = MACHXO2_LOW_DELAY_USEC;
|
|
|
|
spi_message_add_tail(&tx[0], &msg);
|
|
|
|
|
|
|
|
tx[1].tx_buf = &erase;
|
|
|
|
tx[1].len = sizeof(erase);
|
|
|
|
spi_message_add_tail(&tx[1], &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
ret = wait_until_not_busy(spi);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
get_status(spi, &status);
|
|
|
|
if (test_bit(FAIL, &status))
|
|
|
|
goto fail;
|
|
|
|
dump_status_reg(&status);
|
|
|
|
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx[2].tx_buf = &initaddr;
|
|
|
|
tx[2].len = sizeof(initaddr);
|
|
|
|
spi_message_add_tail(&tx[2], &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
fail:
|
|
|
|
dev_err(&mgr->dev, "Error during FPGA init.\n");
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int machxo2_write(struct fpga_manager *mgr, const char *buf,
|
|
|
|
size_t count)
|
|
|
|
{
|
|
|
|
struct spi_device *spi = mgr->priv;
|
|
|
|
struct spi_message msg;
|
|
|
|
struct spi_transfer tx;
|
|
|
|
static const u8 progincr[] = LSC_PROGINCRNV;
|
|
|
|
u8 payload[MACHXO2_BUF_SIZE];
|
|
|
|
unsigned long status;
|
|
|
|
int i, ret;
|
|
|
|
|
|
|
|
if (count % MACHXO2_PAGE_SIZE != 0) {
|
|
|
|
dev_err(&mgr->dev, "Malformed payload.\n");
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
memcpy(payload, &progincr, sizeof(progincr));
|
|
|
|
for (i = 0; i < count; i += MACHXO2_PAGE_SIZE) {
|
|
|
|
memcpy(&payload[sizeof(progincr)], &buf[i], MACHXO2_PAGE_SIZE);
|
|
|
|
memset(&tx, 0, sizeof(tx));
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx.tx_buf = payload;
|
|
|
|
tx.len = MACHXO2_BUF_SIZE;
|
|
|
|
tx.delay_usecs = MACHXO2_HIGH_DELAY_USEC;
|
|
|
|
spi_message_add_tail(&tx, &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret) {
|
|
|
|
dev_err(&mgr->dev, "Error loading the bitstream.\n");
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int machxo2_write_complete(struct fpga_manager *mgr,
|
|
|
|
struct fpga_image_info *info)
|
|
|
|
{
|
|
|
|
struct spi_device *spi = mgr->priv;
|
|
|
|
struct spi_message msg;
|
|
|
|
struct spi_transfer tx[2];
|
|
|
|
static const u8 progdone[] = ISC_PROGRAMDONE;
|
|
|
|
static const u8 refresh[] = LSC_REFRESH;
|
|
|
|
unsigned long status;
|
|
|
|
int ret, refreshloop = 0;
|
|
|
|
|
|
|
|
memset(tx, 0, sizeof(tx));
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx[0].tx_buf = &progdone;
|
|
|
|
tx[0].len = sizeof(progdone);
|
|
|
|
spi_message_add_tail(&tx[0], &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
ret = wait_until_not_busy(spi);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
if (!test_bit(DONE, &status)) {
|
|
|
|
machxo2_cleanup(mgr);
|
|
|
|
goto fail;
|
|
|
|
}
|
|
|
|
|
|
|
|
do {
|
|
|
|
spi_message_init(&msg);
|
|
|
|
tx[1].tx_buf = &refresh;
|
|
|
|
tx[1].len = sizeof(refresh);
|
|
|
|
tx[1].delay_usecs = MACHXO2_REFRESH_USEC;
|
|
|
|
spi_message_add_tail(&tx[1], &msg);
|
|
|
|
ret = spi_sync(spi, &msg);
|
|
|
|
if (ret)
|
|
|
|
goto fail;
|
|
|
|
|
|
|
|
/* check refresh status */
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
if (!test_bit(BUSY, &status) && test_bit(DONE, &status) &&
|
|
|
|
get_err(&status) == ENOERR)
|
|
|
|
break;
|
|
|
|
if (++refreshloop == MACHXO2_MAX_REFRESH_LOOP) {
|
|
|
|
machxo2_cleanup(mgr);
|
|
|
|
goto fail;
|
|
|
|
}
|
|
|
|
} while (1);
|
|
|
|
|
|
|
|
get_status(spi, &status);
|
|
|
|
dump_status_reg(&status);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
fail:
|
|
|
|
dev_err(&mgr->dev, "Refresh failed.\n");
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static const struct fpga_manager_ops machxo2_ops = {
|
|
|
|
.state = machxo2_spi_state,
|
|
|
|
.write_init = machxo2_write_init,
|
|
|
|
.write = machxo2_write,
|
|
|
|
.write_complete = machxo2_write_complete,
|
|
|
|
};
|
|
|
|
|
|
|
|
static int machxo2_spi_probe(struct spi_device *spi)
|
|
|
|
{
|
|
|
|
struct device *dev = &spi->dev;
|
2018-05-16 17:49:55 -06:00
|
|
|
struct fpga_manager *mgr;
|
|
|
|
int ret;
|
2018-04-16 21:43:36 -06:00
|
|
|
|
|
|
|
if (spi->max_speed_hz > MACHXO2_MAX_SPEED) {
|
|
|
|
dev_err(dev, "Speed is too high\n");
|
|
|
|
return -EINVAL;
|
|
|
|
}
|
|
|
|
|
2018-05-16 17:49:55 -06:00
|
|
|
mgr = fpga_mgr_create(dev, "Lattice MachXO2 SPI FPGA Manager",
|
|
|
|
&machxo2_ops, spi);
|
|
|
|
if (!mgr)
|
|
|
|
return -ENOMEM;
|
|
|
|
|
|
|
|
spi_set_drvdata(spi, mgr);
|
|
|
|
|
|
|
|
ret = fpga_mgr_register(mgr);
|
|
|
|
if (ret)
|
|
|
|
fpga_mgr_free(mgr);
|
|
|
|
|
|
|
|
return ret;
|
2018-04-16 21:43:36 -06:00
|
|
|
}
|
|
|
|
|
|
|
|
static int machxo2_spi_remove(struct spi_device *spi)
|
|
|
|
{
|
2018-05-16 17:49:55 -06:00
|
|
|
struct fpga_manager *mgr = spi_get_drvdata(spi);
|
2018-04-16 21:43:36 -06:00
|
|
|
|
2018-05-16 17:49:55 -06:00
|
|
|
fpga_mgr_unregister(mgr);
|
2018-04-16 21:43:36 -06:00
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static const struct of_device_id of_match[] = {
|
|
|
|
{ .compatible = "lattice,machxo2-slave-spi", },
|
|
|
|
{}
|
|
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(of, of_match);
|
|
|
|
|
|
|
|
static const struct spi_device_id lattice_ids[] = {
|
|
|
|
{ "machxo2-slave-spi", 0 },
|
|
|
|
{ },
|
|
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(spi, lattice_ids);
|
|
|
|
|
|
|
|
static struct spi_driver machxo2_spi_driver = {
|
|
|
|
.driver = {
|
|
|
|
.name = "machxo2-slave-spi",
|
|
|
|
.of_match_table = of_match_ptr(of_match),
|
|
|
|
},
|
|
|
|
.probe = machxo2_spi_probe,
|
|
|
|
.remove = machxo2_spi_remove,
|
|
|
|
.id_table = lattice_ids,
|
|
|
|
};
|
|
|
|
|
|
|
|
module_spi_driver(machxo2_spi_driver)
|
|
|
|
|
|
|
|
MODULE_AUTHOR("Paolo Pisati <p.pisati@gmail.com>");
|
|
|
|
MODULE_DESCRIPTION("Load Lattice FPGA firmware over SPI");
|
|
|
|
MODULE_LICENSE("GPL v2");
|