alistair23-linux/drivers/mmc/host/sdhci-of-arasan.c

494 lines
13 KiB
C
Raw Normal View History

/*
* Arasan Secure Digital Host Controller Interface.
* Copyright (C) 2011 - 2012 Michal Simek <monstr@monstr.eu>
* Copyright (c) 2012 Wind River Systems, Inc.
* Copyright (C) 2013 Pengutronix e.K.
* Copyright (C) 2013 Xilinx Inc.
*
* Based on sdhci-of-esdhc.c
*
* Copyright (c) 2007 Freescale Semiconductor, Inc.
* Copyright (c) 2009 MontaVista Software, Inc.
*
* Authors: Xiaobo Xie <X.Xie@freescale.com>
* Anton Vorontsov <avorontsov@ru.mvista.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or (at
* your option) any later version.
*/
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/phy/phy.h>
#include <linux/regmap.h>
#include "sdhci-pltfm.h"
#define SDHCI_ARASAN_CLK_CTRL_OFFSET 0x2c
#define SDHCI_ARASAN_VENDOR_REGISTER 0x78
#define VENDOR_ENHANCED_STROBE BIT(0)
#define CLK_CTRL_TIMEOUT_SHIFT 16
#define CLK_CTRL_TIMEOUT_MASK (0xf << CLK_CTRL_TIMEOUT_SHIFT)
#define CLK_CTRL_TIMEOUT_MIN_EXP 13
/*
* On some SoCs the syscon area has a feature where the upper 16-bits of
* each 32-bit register act as a write mask for the lower 16-bits. This allows
* atomic updates of the register without locking. This macro is used on SoCs
* that have that feature.
*/
#define HIWORD_UPDATE(val, mask, shift) \
((val) << (shift) | (mask) << ((shift) + 16))
/**
* struct sdhci_arasan_soc_ctl_field - Field used in sdhci_arasan_soc_ctl_map
*
* @reg: Offset within the syscon of the register containing this field
* @width: Number of bits for this field
* @shift: Bit offset within @reg of this field (or -1 if not avail)
*/
struct sdhci_arasan_soc_ctl_field {
u32 reg;
u16 width;
s16 shift;
};
/**
* struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers
*
* It's up to the licensee of the Arsan IP block to make these available
* somewhere if needed. Presumably these will be scattered somewhere that's
* accessible via the syscon API.
*
* @baseclkfreq: Where to find corecfg_baseclkfreq
* @hiword_update: If true, use HIWORD_UPDATE to access the syscon
*/
struct sdhci_arasan_soc_ctl_map {
struct sdhci_arasan_soc_ctl_field baseclkfreq;
bool hiword_update;
};
/**
* struct sdhci_arasan_data
* @clk_ahb: Pointer to the AHB clock
* @phy: Pointer to the generic phy
* @phy_on: True if the PHY is turned on.
* @soc_ctl_base: Pointer to regmap for syscon for soc_ctl registers.
* @soc_ctl_map: Map to get offsets into soc_ctl registers.
*/
struct sdhci_arasan_data {
struct clk *clk_ahb;
struct phy *phy;
mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes In commit 802ac39a5566 ("mmc: sdhci-of-arasan: fix set_clock when a phy is supported") we added code to power the PHY off and on whenever the clock was changed but we avoided doing the power cycle code when the clock was low speed. Let's now do it always. Although there may be other reasons for power cycling the PHY when the clock changes, one of the main reasons is that we need to give the DLL a chance to re-lock with the new clock. One of the things that the DLL is for is tuning the Receive Clock in HS200 mode and STRB in HS400 mode. Thus it is clear that we should make sure we power cycle the PHY (and wait for the DLL to lock) when we know we'll be in one of these two speed modes. That's what the original code did, though it used the clock rate rather than the speed mode. However, even in speed modes other than HS200,/HS400 the DLL is used for something since it can be clearly observed that the PHY doesn't function properly if you leave the DLL off. Although it appears less important to power cycle the PHY and wait for the DLL to lock when not in HS200/HS400 modes (no bugs were reported), it still seems wise to let the locking always happen nevertheless. Note: as part of this, we make sure that we never try to turn the PHY on when the clock is off (when the clock rate is 0). The PHY cannot work when the clock is off since its DLL can't lock. This change requires ("phy: rockchip-emmc: Increase lock time allowance") and will cause problems if picked without that change. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-20 11:56:45 -06:00
bool phy_on;
struct regmap *soc_ctl_base;
const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
};
static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = {
.baseclkfreq = { .reg = 0xf000, .width = 8, .shift = 8 },
.hiword_update = true,
};
/**
* sdhci_arasan_syscon_write - Write to a field in soc_ctl registers
*
* This function allows writing to fields in sdhci_arasan_soc_ctl_map.
* Note that if a field is specified as not available (shift < 0) then
* this function will silently return an error code. It will be noisy
* and print errors for any other (unexpected) errors.
*
* @host: The sdhci_host
* @fld: The field to write to
* @val: The value to write
*/
static int sdhci_arasan_syscon_write(struct sdhci_host *host,
const struct sdhci_arasan_soc_ctl_field *fld,
u32 val)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
struct regmap *soc_ctl_base = sdhci_arasan->soc_ctl_base;
u32 reg = fld->reg;
u16 width = fld->width;
s16 shift = fld->shift;
int ret;
/*
* Silently return errors for shift < 0 so caller doesn't have
* to check for fields which are optional. For fields that
* are required then caller needs to do something special
* anyway.
*/
if (shift < 0)
return -EINVAL;
if (sdhci_arasan->soc_ctl_map->hiword_update)
ret = regmap_write(soc_ctl_base, reg,
HIWORD_UPDATE(val, GENMASK(width, 0),
shift));
else
ret = regmap_update_bits(soc_ctl_base, reg,
GENMASK(shift + width, shift),
val << shift);
/* Yell about (unexpected) regmap errors */
if (ret)
pr_warn("%s: Regmap write fail: %d\n",
mmc_hostname(host->mmc), ret);
return ret;
}
static unsigned int sdhci_arasan_get_timeout_clock(struct sdhci_host *host)
{
u32 div;
unsigned long freq;
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
div = readl(host->ioaddr + SDHCI_ARASAN_CLK_CTRL_OFFSET);
div = (div & CLK_CTRL_TIMEOUT_MASK) >> CLK_CTRL_TIMEOUT_SHIFT;
freq = clk_get_rate(pltfm_host->clk);
freq /= 1 << (CLK_CTRL_TIMEOUT_MIN_EXP + div);
return freq;
}
static void sdhci_arasan_set_clock(struct sdhci_host *host, unsigned int clock)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes In commit 802ac39a5566 ("mmc: sdhci-of-arasan: fix set_clock when a phy is supported") we added code to power the PHY off and on whenever the clock was changed but we avoided doing the power cycle code when the clock was low speed. Let's now do it always. Although there may be other reasons for power cycling the PHY when the clock changes, one of the main reasons is that we need to give the DLL a chance to re-lock with the new clock. One of the things that the DLL is for is tuning the Receive Clock in HS200 mode and STRB in HS400 mode. Thus it is clear that we should make sure we power cycle the PHY (and wait for the DLL to lock) when we know we'll be in one of these two speed modes. That's what the original code did, though it used the clock rate rather than the speed mode. However, even in speed modes other than HS200,/HS400 the DLL is used for something since it can be clearly observed that the PHY doesn't function properly if you leave the DLL off. Although it appears less important to power cycle the PHY and wait for the DLL to lock when not in HS200/HS400 modes (no bugs were reported), it still seems wise to let the locking always happen nevertheless. Note: as part of this, we make sure that we never try to turn the PHY on when the clock is off (when the clock rate is 0). The PHY cannot work when the clock is off since its DLL can't lock. This change requires ("phy: rockchip-emmc: Increase lock time allowance") and will cause problems if picked without that change. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-20 11:56:45 -06:00
if (sdhci_arasan->phy_on && !IS_ERR(sdhci_arasan->phy)) {
sdhci_arasan->phy_on = false;
spin_unlock_irq(&host->lock);
phy_power_off(sdhci_arasan->phy);
spin_lock_irq(&host->lock);
}
sdhci_set_clock(host, clock);
mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes In commit 802ac39a5566 ("mmc: sdhci-of-arasan: fix set_clock when a phy is supported") we added code to power the PHY off and on whenever the clock was changed but we avoided doing the power cycle code when the clock was low speed. Let's now do it always. Although there may be other reasons for power cycling the PHY when the clock changes, one of the main reasons is that we need to give the DLL a chance to re-lock with the new clock. One of the things that the DLL is for is tuning the Receive Clock in HS200 mode and STRB in HS400 mode. Thus it is clear that we should make sure we power cycle the PHY (and wait for the DLL to lock) when we know we'll be in one of these two speed modes. That's what the original code did, though it used the clock rate rather than the speed mode. However, even in speed modes other than HS200,/HS400 the DLL is used for something since it can be clearly observed that the PHY doesn't function properly if you leave the DLL off. Although it appears less important to power cycle the PHY and wait for the DLL to lock when not in HS200/HS400 modes (no bugs were reported), it still seems wise to let the locking always happen nevertheless. Note: as part of this, we make sure that we never try to turn the PHY on when the clock is off (when the clock rate is 0). The PHY cannot work when the clock is off since its DLL can't lock. This change requires ("phy: rockchip-emmc: Increase lock time allowance") and will cause problems if picked without that change. Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com> Tested-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-06-20 11:56:45 -06:00
if (host->mmc->actual_clock && !IS_ERR(sdhci_arasan->phy)) {
sdhci_arasan->phy_on = true;
spin_unlock_irq(&host->lock);
phy_power_on(sdhci_arasan->phy);
spin_lock_irq(&host->lock);
}
}
static void sdhci_arasan_hs400_enhanced_strobe(struct mmc_host *mmc,
struct mmc_ios *ios)
{
u32 vendor;
struct sdhci_host *host = mmc_priv(mmc);
vendor = readl(host->ioaddr + SDHCI_ARASAN_VENDOR_REGISTER);
if (ios->enhanced_strobe)
vendor |= VENDOR_ENHANCED_STROBE;
else
vendor &= ~VENDOR_ENHANCED_STROBE;
writel(vendor, host->ioaddr + SDHCI_ARASAN_VENDOR_REGISTER);
}
static struct sdhci_ops sdhci_arasan_ops = {
.set_clock = sdhci_arasan_set_clock,
.get_max_clock = sdhci_pltfm_clk_get_max_clock,
.get_timeout_clock = sdhci_arasan_get_timeout_clock,
.set_bus_width = sdhci_set_bus_width,
.reset = sdhci_reset,
.set_uhs_signaling = sdhci_set_uhs_signaling,
};
static struct sdhci_pltfm_data sdhci_arasan_pdata = {
.ops = &sdhci_arasan_ops,
.quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN,
};
#ifdef CONFIG_PM_SLEEP
/**
* sdhci_arasan_suspend - Suspend method for the driver
* @dev: Address of the device structure
* Returns 0 on success and error value on error
*
* Put the device in a low power state.
*/
static int sdhci_arasan_suspend(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
int ret;
ret = sdhci_suspend_host(host);
if (ret)
return ret;
if (!IS_ERR(sdhci_arasan->phy)) {
ret = phy_power_off(sdhci_arasan->phy);
if (ret) {
dev_err(dev, "Cannot power off phy.\n");
sdhci_resume_host(host);
return ret;
}
}
clk_disable(pltfm_host->clk);
clk_disable(sdhci_arasan->clk_ahb);
return 0;
}
/**
* sdhci_arasan_resume - Resume method for the driver
* @dev: Address of the device structure
* Returns 0 on success and error value on error
*
* Resume operation after suspend
*/
static int sdhci_arasan_resume(struct device *dev)
{
struct platform_device *pdev = to_platform_device(dev);
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
int ret;
ret = clk_enable(sdhci_arasan->clk_ahb);
if (ret) {
dev_err(dev, "Cannot enable AHB clock.\n");
return ret;
}
ret = clk_enable(pltfm_host->clk);
if (ret) {
dev_err(dev, "Cannot enable SD clock.\n");
return ret;
}
if (!IS_ERR(sdhci_arasan->phy)) {
ret = phy_power_on(sdhci_arasan->phy);
if (ret) {
dev_err(dev, "Cannot power on phy.\n");
return ret;
}
}
return sdhci_resume_host(host);
}
#endif /* ! CONFIG_PM_SLEEP */
static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend,
sdhci_arasan_resume);
static const struct of_device_id sdhci_arasan_of_match[] = {
/* SoC-specific compatible strings w/ soc_ctl_map */
{
.compatible = "rockchip,rk3399-sdhci-5.1",
.data = &rk3399_soc_ctl_map,
},
/* Generic compatible below here */
{ .compatible = "arasan,sdhci-8.9a" },
{ .compatible = "arasan,sdhci-5.1" },
{ .compatible = "arasan,sdhci-4.9a" },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
/**
* sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq
*
* The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin. This
* function can be used to make that happen.
*
* NOTES:
* - Many existing devices don't seem to do this and work fine. To keep
* compatibility for old hardware where the device tree doesn't provide a
* register map, this function is a noop if a soc_ctl_map hasn't been provided
* for this platform.
* - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider
* to achieve lower clock rates. That means that this function is called once
* at probe time and never called again.
*
* @host: The sdhci_host
*/
static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
const struct sdhci_arasan_soc_ctl_map *soc_ctl_map =
sdhci_arasan->soc_ctl_map;
u32 mhz = DIV_ROUND_CLOSEST(clk_get_rate(pltfm_host->clk), 1000000);
/* Having a map is optional */
if (!soc_ctl_map)
return;
/* If we have a map, we expect to have a syscon */
if (!sdhci_arasan->soc_ctl_base) {
pr_warn("%s: Have regmap, but no soc-ctl-syscon\n",
mmc_hostname(host->mmc));
return;
}
sdhci_arasan_syscon_write(host, &soc_ctl_map->baseclkfreq, mhz);
}
static int sdhci_arasan_probe(struct platform_device *pdev)
{
int ret;
const struct of_device_id *match;
struct device_node *node;
struct clk *clk_xin;
struct sdhci_host *host;
struct sdhci_pltfm_host *pltfm_host;
struct sdhci_arasan_data *sdhci_arasan;
host = sdhci_pltfm_init(pdev, &sdhci_arasan_pdata,
sizeof(*sdhci_arasan));
if (IS_ERR(host))
return PTR_ERR(host);
pltfm_host = sdhci_priv(host);
sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node);
sdhci_arasan->soc_ctl_map = match->data;
node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0);
if (node) {
sdhci_arasan->soc_ctl_base = syscon_node_to_regmap(node);
of_node_put(node);
if (IS_ERR(sdhci_arasan->soc_ctl_base)) {
ret = PTR_ERR(sdhci_arasan->soc_ctl_base);
if (ret != -EPROBE_DEFER)
dev_err(&pdev->dev, "Can't get syscon: %d\n",
ret);
goto err_pltfm_free;
}
}
sdhci_arasan->clk_ahb = devm_clk_get(&pdev->dev, "clk_ahb");
if (IS_ERR(sdhci_arasan->clk_ahb)) {
dev_err(&pdev->dev, "clk_ahb clock not found.\n");
ret = PTR_ERR(sdhci_arasan->clk_ahb);
goto err_pltfm_free;
}
clk_xin = devm_clk_get(&pdev->dev, "clk_xin");
if (IS_ERR(clk_xin)) {
dev_err(&pdev->dev, "clk_xin clock not found.\n");
ret = PTR_ERR(clk_xin);
goto err_pltfm_free;
}
ret = clk_prepare_enable(sdhci_arasan->clk_ahb);
if (ret) {
dev_err(&pdev->dev, "Unable to enable AHB clock.\n");
goto err_pltfm_free;
}
ret = clk_prepare_enable(clk_xin);
if (ret) {
dev_err(&pdev->dev, "Unable to enable SD clock.\n");
goto clk_dis_ahb;
}
sdhci_get_of_property(pdev);
pltfm_host->clk = clk_xin;
sdhci_arasan_update_baseclkfreq(host);
ret = mmc_of_parse(host->mmc);
if (ret) {
dev_err(&pdev->dev, "parsing dt failed (%u)\n", ret);
goto clk_disable_all;
}
sdhci_arasan->phy = ERR_PTR(-ENODEV);
if (of_device_is_compatible(pdev->dev.of_node,
"arasan,sdhci-5.1")) {
sdhci_arasan->phy = devm_phy_get(&pdev->dev,
"phy_arasan");
if (IS_ERR(sdhci_arasan->phy)) {
ret = PTR_ERR(sdhci_arasan->phy);
dev_err(&pdev->dev, "No phy for arasan,sdhci-5.1.\n");
goto clk_disable_all;
}
ret = phy_init(sdhci_arasan->phy);
if (ret < 0) {
dev_err(&pdev->dev, "phy_init err.\n");
goto clk_disable_all;
}
host->mmc_host_ops.hs400_enhanced_strobe =
sdhci_arasan_hs400_enhanced_strobe;
}
ret = sdhci_add_host(host);
if (ret)
goto err_add_host;
return 0;
err_add_host:
if (!IS_ERR(sdhci_arasan->phy))
phy_exit(sdhci_arasan->phy);
clk_disable_all:
clk_disable_unprepare(clk_xin);
clk_dis_ahb:
clk_disable_unprepare(sdhci_arasan->clk_ahb);
err_pltfm_free:
sdhci_pltfm_free(pdev);
return ret;
}
static int sdhci_arasan_remove(struct platform_device *pdev)
{
int ret;
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
struct clk *clk_ahb = sdhci_arasan->clk_ahb;
if (!IS_ERR(sdhci_arasan->phy)) {
phy_power_off(sdhci_arasan->phy);
phy_exit(sdhci_arasan->phy);
}
ret = sdhci_pltfm_unregister(pdev);
clk_disable_unprepare(clk_ahb);
return ret;
}
static struct platform_driver sdhci_arasan_driver = {
.driver = {
.name = "sdhci-arasan",
.of_match_table = sdhci_arasan_of_match,
.pm = &sdhci_arasan_dev_pm_ops,
},
.probe = sdhci_arasan_probe,
.remove = sdhci_arasan_remove,
};
module_platform_driver(sdhci_arasan_driver);
MODULE_DESCRIPTION("Driver for the Arasan SDHCI Controller");
MODULE_AUTHOR("Soeren Brinkmann <soren.brinkmann@xilinx.com>");
MODULE_LICENSE("GPL");