1
0
Fork 0
alistair23-linux/drivers/gpu/drm/i915/intel_bios.h

616 lines
17 KiB
C
Raw Normal View History

/*
drm/i915: Correct eDP panel power sequencing delay computations Store the panel power sequencing delays in the dp private structure, rather than the global device structure. Who knows, maybe we'll get more than one eDP device in the future. From the eDP spec, we need the following numbers: T1 + T3 Power on to Aux Channel operation (panel_power_up_delay) This marks how long it takes the panel to boot up and get ready to receive aux channel communications. T8 Video signal to backlight on (backlight_on_delay) Once a valid video signal is being sent to the device, it can take a while before the panel is actuall showing useful data. This delay allows the panel to get something reasonable up before the backlight is turned on. T9 Backlight off to video off (backlight_off_delay) Turning the backlight off can take a moment, so this delay makes sure there is still valid video data on the screen. T10 Video off to power off (panel_power_down_delay) Presumably this delay allows the panel to perform an orderly shutdown of the display. T11 + T12 Power off to power on (panel_power_cycle_delay) So, once you turn the panel off, you have to wait a while before you can turn it back on. This delay is usually the longest in the entire sequence. Neither the VBIOS source code nor the hardware documentation has a clear mapping between the delay values they provide and those required by the eDP spec. The VBIOS code actually uses two different labels for the delay values in the five words of the relevant VBT table. **** MORE LATER *** Look at both the current hardware register settings and the VBT specified panel power sequencing timings. Use the maximum of the two delays, to make sure things work reliably. If there is no VBT data, then those values will be initialized to zero, so we'll just use the values as programmed in the hardware. Note that the BIOS just fetches delays from the VBT table to place in the hardware registers, so we should get the same values from both places, except for rounding. VBT doesn't provide any values for T1 or T2, so we'll always just use the hardware value for that. The panel power up delay is thus T1 + T2 + T3, which should be sufficient in all cases. The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy for T11, which isn't available anywhere. For the backlight delays, the eDP spec says T6 + T8 is the delay from the end of link training to backlight on and T9 is the delay from backlight off until video off. The hardware provides a 'backlight on' delay, which I'm taking to be T6 + T8 while the VBT provides something called 'T7', which I'm assuming is s On the macbook air I'm testing with, this yields a power-up delay of over 200ms and a power-down delay of over 600ms. It all works now, but we're frobbing these power controls several times during mode setting, making the whole process take an awfully long time. Signed-off-by: Keith Packard <keithp@keithp.com>
2011-09-28 17:48:10 -06:00
* Copyright © 2006 Intel Corporation
*
* Permission is hereby granted, free of charge, to any person obtaining a
* copy of this software and associated documentation files (the "Software"),
* to deal in the Software without restriction, including without limitation
* the rights to use, copy, modify, merge, publish, distribute, sublicense,
* and/or sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice (including the next
* paragraph) shall be included in all copies or substantial portions of the
* Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
* THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
* SOFTWARE.
*
* Authors:
* Eric Anholt <eric@anholt.net>
*
*/
#ifndef _I830_BIOS_H_
#define _I830_BIOS_H_
#include "drmP.h"
struct vbt_header {
u8 signature[20]; /**< Always starts with 'VBT$' */
u16 version; /**< decimal */
u16 header_size; /**< in bytes */
u16 vbt_size; /**< in bytes */
u8 vbt_checksum;
u8 reserved0;
u32 bdb_offset; /**< from beginning of VBT */
u32 aim_offset[4]; /**< from beginning of VBT */
} __attribute__((packed));
struct bdb_header {
u8 signature[16]; /**< Always 'BIOS_DATA_BLOCK' */
u16 version; /**< decimal */
u16 header_size; /**< in bytes */
u16 bdb_size; /**< in bytes */
};
/* strictly speaking, this is a "skip" block, but it has interesting info */
struct vbios_data {
u8 type; /* 0 == desktop, 1 == mobile */
u8 relstage;
u8 chipset;
u8 lvds_present:1;
u8 tv_present:1;
u8 rsvd2:6; /* finish byte */
u8 rsvd3[4];
u8 signon[155];
u8 copyright[61];
u16 code_segment;
u8 dos_boot_mode;
u8 bandwidth_percent;
u8 rsvd4; /* popup memory size */
u8 resize_pci_bios;
u8 rsvd5; /* is crt already on ddc2 */
} __attribute__((packed));
/*
* There are several types of BIOS data blocks (BDBs), each block has
* an ID and size in the first 3 bytes (ID in first, size in next 2).
* Known types are listed below.
*/
#define BDB_GENERAL_FEATURES 1
#define BDB_GENERAL_DEFINITIONS 2
#define BDB_OLD_TOGGLE_LIST 3
#define BDB_MODE_SUPPORT_LIST 4
#define BDB_GENERIC_MODE_TABLE 5
#define BDB_EXT_MMIO_REGS 6
#define BDB_SWF_IO 7
#define BDB_SWF_MMIO 8
#define BDB_DOT_CLOCK_TABLE 9
#define BDB_MODE_REMOVAL_TABLE 10
#define BDB_CHILD_DEVICE_TABLE 11
#define BDB_DRIVER_FEATURES 12
#define BDB_DRIVER_PERSISTENCE 13
#define BDB_EXT_TABLE_PTRS 14
#define BDB_DOT_CLOCK_OVERRIDE 15
#define BDB_DISPLAY_SELECT 16
/* 17 rsvd */
#define BDB_DRIVER_ROTATION 18
#define BDB_DISPLAY_REMOVE 19
#define BDB_OEM_CUSTOM 20
#define BDB_EFP_LIST 21 /* workarounds for VGA hsync/vsync */
#define BDB_SDVO_LVDS_OPTIONS 22
#define BDB_SDVO_PANEL_DTDS 23
#define BDB_SDVO_LVDS_PNP_IDS 24
#define BDB_SDVO_LVDS_POWER_SEQ 25
#define BDB_TV_OPTIONS 26
#define BDB_EDP 27
#define BDB_LVDS_OPTIONS 40
#define BDB_LVDS_LFP_DATA_PTRS 41
#define BDB_LVDS_LFP_DATA 42
#define BDB_LVDS_BACKLIGHT 43
#define BDB_LVDS_POWER 44
#define BDB_SKIP 254 /* VBIOS private block, ignore */
struct bdb_general_features {
/* bits 1 */
u8 panel_fitting:2;
u8 flexaim:1;
u8 msg_enable:1;
u8 clear_screen:3;
u8 color_flip:1;
/* bits 2 */
u8 download_ext_vbt:1;
u8 enable_ssc:1;
u8 ssc_freq:1;
u8 enable_lfp_on_override:1;
u8 disable_ssc_ddt:1;
u8 rsvd7:1;
u8 display_clock_mode:1;
u8 rsvd8:1; /* finish byte */
/* bits 3 */
u8 disable_smooth_vision:1;
u8 single_dvi:1;
u8 rsvd9:6; /* finish byte */
/* bits 4 */
u8 legacy_monitor_detect;
/* bits 5 */
u8 int_crt_support:1;
u8 int_tv_support:1;
u8 int_efp_support:1;
u8 dp_ssc_enb:1; /* PCH attached eDP supports SSC */
u8 dp_ssc_freq:1; /* SSC freq for PCH attached eDP */
u8 rsvd11:3; /* finish byte */
} __attribute__((packed));
/* pre-915 */
#define GPIO_PIN_DVI_LVDS 0x03 /* "DVI/LVDS DDC GPIO pins" */
#define GPIO_PIN_ADD_I2C 0x05 /* "ADDCARD I2C GPIO pins" */
#define GPIO_PIN_ADD_DDC 0x04 /* "ADDCARD DDC GPIO pins" */
#define GPIO_PIN_ADD_DDC_I2C 0x06 /* "ADDCARD DDC/I2C GPIO pins" */
/* Pre 915 */
#define DEVICE_TYPE_NONE 0x00
#define DEVICE_TYPE_CRT 0x01
#define DEVICE_TYPE_TV 0x09
#define DEVICE_TYPE_EFP 0x12
#define DEVICE_TYPE_LFP 0x22
/* On 915+ */
#define DEVICE_TYPE_CRT_DPMS 0x6001
#define DEVICE_TYPE_CRT_DPMS_HOTPLUG 0x4001
#define DEVICE_TYPE_TV_COMPOSITE 0x0209
#define DEVICE_TYPE_TV_MACROVISION 0x0289
#define DEVICE_TYPE_TV_RF_COMPOSITE 0x020c
#define DEVICE_TYPE_TV_SVIDEO_COMPOSITE 0x0609
#define DEVICE_TYPE_TV_SCART 0x0209
#define DEVICE_TYPE_TV_CODEC_HOTPLUG_PWR 0x6009
#define DEVICE_TYPE_EFP_HOTPLUG_PWR 0x6012
#define DEVICE_TYPE_EFP_DVI_HOTPLUG_PWR 0x6052
#define DEVICE_TYPE_EFP_DVI_I 0x6053
#define DEVICE_TYPE_EFP_DVI_D_DUAL 0x6152
#define DEVICE_TYPE_EFP_DVI_D_HDCP 0x60d2
#define DEVICE_TYPE_OPENLDI_HOTPLUG_PWR 0x6062
#define DEVICE_TYPE_OPENLDI_DUALPIX 0x6162
#define DEVICE_TYPE_LFP_PANELLINK 0x5012
#define DEVICE_TYPE_LFP_CMOS_PWR 0x5042
#define DEVICE_TYPE_LFP_LVDS_PWR 0x5062
#define DEVICE_TYPE_LFP_LVDS_DUAL 0x5162
#define DEVICE_TYPE_LFP_LVDS_DUAL_HDCP 0x51e2
#define DEVICE_CFG_NONE 0x00
#define DEVICE_CFG_12BIT_DVOB 0x01
#define DEVICE_CFG_12BIT_DVOC 0x02
#define DEVICE_CFG_24BIT_DVOBC 0x09
#define DEVICE_CFG_24BIT_DVOCB 0x0a
#define DEVICE_CFG_DUAL_DVOB 0x11
#define DEVICE_CFG_DUAL_DVOC 0x12
#define DEVICE_CFG_DUAL_DVOBC 0x13
#define DEVICE_CFG_DUAL_LINK_DVOBC 0x19
#define DEVICE_CFG_DUAL_LINK_DVOCB 0x1a
#define DEVICE_WIRE_NONE 0x00
#define DEVICE_WIRE_DVOB 0x01
#define DEVICE_WIRE_DVOC 0x02
#define DEVICE_WIRE_DVOBC 0x03
#define DEVICE_WIRE_DVOBB 0x05
#define DEVICE_WIRE_DVOCC 0x06
#define DEVICE_WIRE_DVOB_MASTER 0x0d
#define DEVICE_WIRE_DVOC_MASTER 0x0e
#define DEVICE_PORT_DVOA 0x00 /* none on 845+ */
#define DEVICE_PORT_DVOB 0x01
#define DEVICE_PORT_DVOC 0x02
struct child_device_config {
u16 handle;
u16 device_type;
u8 device_id[10]; /* ascii string */
u16 addin_offset;
u8 dvo_port; /* See Device_PORT_* above */
u8 i2c_pin;
u8 slave_addr;
u8 ddc_pin;
u16 edid_ptr;
u8 dvo_cfg; /* See DEVICE_CFG_* above */
u8 dvo2_port;
u8 i2c2_pin;
u8 slave2_addr;
u8 ddc2_pin;
u8 capabilities;
u8 dvo_wiring;/* See DEVICE_WIRE_* above */
u8 dvo2_wiring;
u16 extended_type;
u8 dvo_function;
} __attribute__((packed));
struct bdb_general_definitions {
/* DDC GPIO */
u8 crt_ddc_gmbus_pin;
/* DPMS bits */
u8 dpms_acpi:1;
u8 skip_boot_crt_detect:1;
u8 dpms_aim:1;
u8 rsvd1:5; /* finish byte */
/* boot device bits */
u8 boot_display[2];
u8 child_dev_size;
/*
* Device info:
* If TV is present, it'll be at devices[0].
* LVDS will be next, either devices[0] or [1], if present.
* On some platforms the number of device is 6. But could be as few as
* 4 if both TV and LVDS are missing.
* And the device num is related with the size of general definition
* block. It is obtained by using the following formula:
* number = (block_size - sizeof(bdb_general_definitions))/
* sizeof(child_device_config);
*/
struct child_device_config devices[0];
} __attribute__((packed));
struct bdb_lvds_options {
u8 panel_type;
u8 rsvd1;
/* LVDS capabilities, stored in a dword */
u8 pfit_mode:2;
u8 pfit_text_mode_enhanced:1;
u8 pfit_gfx_mode_enhanced:1;
u8 pfit_ratio_auto:1;
u8 pixel_dither:1;
u8 lvds_edid:1;
u8 rsvd2:1;
u8 rsvd4;
} __attribute__((packed));
/* LFP pointer table contains entries to the struct below */
struct bdb_lvds_lfp_data_ptr {
u16 fp_timing_offset; /* offsets are from start of bdb */
u8 fp_table_size;
u16 dvo_timing_offset;
u8 dvo_table_size;
u16 panel_pnp_id_offset;
u8 pnp_table_size;
} __attribute__((packed));
struct bdb_lvds_lfp_data_ptrs {
u8 lvds_entries; /* followed by one or more lvds_data_ptr structs */
struct bdb_lvds_lfp_data_ptr ptr[16];
} __attribute__((packed));
/* LFP data has 3 blocks per entry */
struct lvds_fp_timing {
u16 x_res;
u16 y_res;
u32 lvds_reg;
u32 lvds_reg_val;
u32 pp_on_reg;
u32 pp_on_reg_val;
u32 pp_off_reg;
u32 pp_off_reg_val;
u32 pp_cycle_reg;
u32 pp_cycle_reg_val;
u32 pfit_reg;
u32 pfit_reg_val;
u16 terminator;
} __attribute__((packed));
struct lvds_dvo_timing {
u16 clock; /**< In 10khz */
u8 hactive_lo;
u8 hblank_lo;
u8 hblank_hi:4;
u8 hactive_hi:4;
u8 vactive_lo;
u8 vblank_lo;
u8 vblank_hi:4;
u8 vactive_hi:4;
u8 hsync_off_lo;
u8 hsync_pulse_width;
u8 vsync_pulse_width:4;
u8 vsync_off:4;
u8 rsvd0:6;
u8 hsync_off_hi:2;
u8 h_image;
u8 v_image;
u8 max_hv;
u8 h_border;
u8 v_border;
u8 rsvd1:3;
u8 digital:2;
u8 vsync_positive:1;
u8 hsync_positive:1;
u8 rsvd2:1;
} __attribute__((packed));
struct lvds_pnp_id {
u16 mfg_name;
u16 product_code;
u32 serial;
u8 mfg_week;
u8 mfg_year;
} __attribute__((packed));
struct bdb_lvds_lfp_data_entry {
struct lvds_fp_timing fp_timing;
struct lvds_dvo_timing dvo_timing;
struct lvds_pnp_id pnp_id;
} __attribute__((packed));
struct bdb_lvds_lfp_data {
struct bdb_lvds_lfp_data_entry data[16];
} __attribute__((packed));
struct aimdb_header {
char signature[16];
char oem_device[20];
u16 aimdb_version;
u16 aimdb_header_size;
u16 aimdb_size;
} __attribute__((packed));
struct aimdb_block {
u8 aimdb_id;
u16 aimdb_size;
} __attribute__((packed));
struct vch_panel_data {
u16 fp_timing_offset;
u8 fp_timing_size;
u16 dvo_timing_offset;
u8 dvo_timing_size;
u16 text_fitting_offset;
u8 text_fitting_size;
u16 graphics_fitting_offset;
u8 graphics_fitting_size;
} __attribute__((packed));
struct vch_bdb_22 {
struct aimdb_block aimdb_block;
struct vch_panel_data panels[16];
} __attribute__((packed));
struct bdb_sdvo_lvds_options {
u8 panel_backlight;
u8 h40_set_panel_type;
u8 panel_type;
u8 ssc_clk_freq;
u16 als_low_trip;
u16 als_high_trip;
u8 sclalarcoeff_tab_row_num;
u8 sclalarcoeff_tab_row_size;
u8 coefficient[8];
u8 panel_misc_bits_1;
u8 panel_misc_bits_2;
u8 panel_misc_bits_3;
u8 panel_misc_bits_4;
} __attribute__((packed));
#define BDB_DRIVER_FEATURE_NO_LVDS 0
#define BDB_DRIVER_FEATURE_INT_LVDS 1
#define BDB_DRIVER_FEATURE_SDVO_LVDS 2
#define BDB_DRIVER_FEATURE_EDP 3
struct bdb_driver_features {
u8 boot_dev_algorithm:1;
u8 block_display_switch:1;
u8 allow_display_switch:1;
u8 hotplug_dvo:1;
u8 dual_view_zoom:1;
u8 int15h_hook:1;
u8 sprite_in_clone:1;
u8 primary_lfp_id:1;
u16 boot_mode_x;
u16 boot_mode_y;
u8 boot_mode_bpp;
u8 boot_mode_refresh;
u16 enable_lfp_primary:1;
u16 selective_mode_pruning:1;
u16 dual_frequency:1;
u16 render_clock_freq:1; /* 0: high freq; 1: low freq */
u16 nt_clone_support:1;
u16 power_scheme_ui:1; /* 0: CUI; 1: 3rd party */
u16 sprite_display_assign:1; /* 0: secondary; 1: primary */
u16 cui_aspect_scaling:1;
u16 preserve_aspect_ratio:1;
u16 sdvo_device_power_down:1;
u16 crt_hotplug:1;
u16 lvds_config:2;
u16 tv_hotplug:1;
u16 hdmi_config:2;
u8 static_display:1;
u8 reserved2:7;
u16 legacy_crt_max_x;
u16 legacy_crt_max_y;
u8 legacy_crt_max_refresh;
u8 hdmi_termination;
u8 custom_vbt_version;
} __attribute__((packed));
#define EDP_18BPP 0
#define EDP_24BPP 1
#define EDP_30BPP 2
#define EDP_RATE_1_62 0
#define EDP_RATE_2_7 1
#define EDP_LANE_1 0
#define EDP_LANE_2 1
#define EDP_LANE_4 3
#define EDP_PREEMPHASIS_NONE 0
#define EDP_PREEMPHASIS_3_5dB 1
#define EDP_PREEMPHASIS_6dB 2
#define EDP_PREEMPHASIS_9_5dB 3
#define EDP_VSWING_0_4V 0
#define EDP_VSWING_0_6V 1
#define EDP_VSWING_0_8V 2
#define EDP_VSWING_1_2V 3
struct edp_power_seq {
drm/i915: Correct eDP panel power sequencing delay computations Store the panel power sequencing delays in the dp private structure, rather than the global device structure. Who knows, maybe we'll get more than one eDP device in the future. From the eDP spec, we need the following numbers: T1 + T3 Power on to Aux Channel operation (panel_power_up_delay) This marks how long it takes the panel to boot up and get ready to receive aux channel communications. T8 Video signal to backlight on (backlight_on_delay) Once a valid video signal is being sent to the device, it can take a while before the panel is actuall showing useful data. This delay allows the panel to get something reasonable up before the backlight is turned on. T9 Backlight off to video off (backlight_off_delay) Turning the backlight off can take a moment, so this delay makes sure there is still valid video data on the screen. T10 Video off to power off (panel_power_down_delay) Presumably this delay allows the panel to perform an orderly shutdown of the display. T11 + T12 Power off to power on (panel_power_cycle_delay) So, once you turn the panel off, you have to wait a while before you can turn it back on. This delay is usually the longest in the entire sequence. Neither the VBIOS source code nor the hardware documentation has a clear mapping between the delay values they provide and those required by the eDP spec. The VBIOS code actually uses two different labels for the delay values in the five words of the relevant VBT table. **** MORE LATER *** Look at both the current hardware register settings and the VBT specified panel power sequencing timings. Use the maximum of the two delays, to make sure things work reliably. If there is no VBT data, then those values will be initialized to zero, so we'll just use the values as programmed in the hardware. Note that the BIOS just fetches delays from the VBT table to place in the hardware registers, so we should get the same values from both places, except for rounding. VBT doesn't provide any values for T1 or T2, so we'll always just use the hardware value for that. The panel power up delay is thus T1 + T2 + T3, which should be sufficient in all cases. The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy for T11, which isn't available anywhere. For the backlight delays, the eDP spec says T6 + T8 is the delay from the end of link training to backlight on and T9 is the delay from backlight off until video off. The hardware provides a 'backlight on' delay, which I'm taking to be T6 + T8 while the VBT provides something called 'T7', which I'm assuming is s On the macbook air I'm testing with, this yields a power-up delay of over 200ms and a power-down delay of over 600ms. It all works now, but we're frobbing these power controls several times during mode setting, making the whole process take an awfully long time. Signed-off-by: Keith Packard <keithp@keithp.com>
2011-09-28 17:48:10 -06:00
u16 t1_t3;
u16 t8;
u16 t9;
u16 t10;
drm/i915: Correct eDP panel power sequencing delay computations Store the panel power sequencing delays in the dp private structure, rather than the global device structure. Who knows, maybe we'll get more than one eDP device in the future. From the eDP spec, we need the following numbers: T1 + T3 Power on to Aux Channel operation (panel_power_up_delay) This marks how long it takes the panel to boot up and get ready to receive aux channel communications. T8 Video signal to backlight on (backlight_on_delay) Once a valid video signal is being sent to the device, it can take a while before the panel is actuall showing useful data. This delay allows the panel to get something reasonable up before the backlight is turned on. T9 Backlight off to video off (backlight_off_delay) Turning the backlight off can take a moment, so this delay makes sure there is still valid video data on the screen. T10 Video off to power off (panel_power_down_delay) Presumably this delay allows the panel to perform an orderly shutdown of the display. T11 + T12 Power off to power on (panel_power_cycle_delay) So, once you turn the panel off, you have to wait a while before you can turn it back on. This delay is usually the longest in the entire sequence. Neither the VBIOS source code nor the hardware documentation has a clear mapping between the delay values they provide and those required by the eDP spec. The VBIOS code actually uses two different labels for the delay values in the five words of the relevant VBT table. **** MORE LATER *** Look at both the current hardware register settings and the VBT specified panel power sequencing timings. Use the maximum of the two delays, to make sure things work reliably. If there is no VBT data, then those values will be initialized to zero, so we'll just use the values as programmed in the hardware. Note that the BIOS just fetches delays from the VBT table to place in the hardware registers, so we should get the same values from both places, except for rounding. VBT doesn't provide any values for T1 or T2, so we'll always just use the hardware value for that. The panel power up delay is thus T1 + T2 + T3, which should be sufficient in all cases. The panel power down delay is T1 + T2 + T12, using T1+T2 as a proxy for T11, which isn't available anywhere. For the backlight delays, the eDP spec says T6 + T8 is the delay from the end of link training to backlight on and T9 is the delay from backlight off until video off. The hardware provides a 'backlight on' delay, which I'm taking to be T6 + T8 while the VBT provides something called 'T7', which I'm assuming is s On the macbook air I'm testing with, this yields a power-up delay of over 200ms and a power-down delay of over 600ms. It all works now, but we're frobbing these power controls several times during mode setting, making the whole process take an awfully long time. Signed-off-by: Keith Packard <keithp@keithp.com>
2011-09-28 17:48:10 -06:00
u16 t11_t12;
} __attribute__ ((packed));
struct edp_link_params {
u8 rate:4;
u8 lanes:4;
u8 preemphasis:4;
u8 vswing:4;
} __attribute__ ((packed));
struct bdb_edp {
struct edp_power_seq power_seqs[16];
u32 color_depth;
u32 sdrrs_msa_timing_delay;
struct edp_link_params link_params[16];
} __attribute__ ((packed));
void intel_setup_bios(struct drm_device *dev);
bool intel_parse_bios(struct drm_device *dev);
/*
* Driver<->VBIOS interaction occurs through scratch bits in
* GR18 & SWF*.
*/
/* GR18 bits are set on display switch and hotkey events */
#define GR18_DRIVER_SWITCH_EN (1<<7) /* 0: VBIOS control, 1: driver control */
#define GR18_HOTKEY_MASK 0x78 /* See also SWF4 15:0 */
#define GR18_HK_NONE (0x0<<3)
#define GR18_HK_LFP_STRETCH (0x1<<3)
#define GR18_HK_TOGGLE_DISP (0x2<<3)
#define GR18_HK_DISP_SWITCH (0x4<<3) /* see SWF14 15:0 for what to enable */
#define GR18_HK_POPUP_DISABLED (0x6<<3)
#define GR18_HK_POPUP_ENABLED (0x7<<3)
#define GR18_HK_PFIT (0x8<<3)
#define GR18_HK_APM_CHANGE (0xa<<3)
#define GR18_HK_MULTIPLE (0xc<<3)
#define GR18_USER_INT_EN (1<<2)
#define GR18_A0000_FLUSH_EN (1<<1)
#define GR18_SMM_EN (1<<0)
/* Set by driver, cleared by VBIOS */
#define SWF00_YRES_SHIFT 16
#define SWF00_XRES_SHIFT 0
#define SWF00_RES_MASK 0xffff
/* Set by VBIOS at boot time and driver at runtime */
#define SWF01_TV2_FORMAT_SHIFT 8
#define SWF01_TV1_FORMAT_SHIFT 0
#define SWF01_TV_FORMAT_MASK 0xffff
#define SWF10_VBIOS_BLC_I2C_EN (1<<29)
#define SWF10_GTT_OVERRIDE_EN (1<<28)
#define SWF10_LFP_DPMS_OVR (1<<27) /* override DPMS on display switch */
#define SWF10_ACTIVE_TOGGLE_LIST_MASK (7<<24)
#define SWF10_OLD_TOGGLE 0x0
#define SWF10_TOGGLE_LIST_1 0x1
#define SWF10_TOGGLE_LIST_2 0x2
#define SWF10_TOGGLE_LIST_3 0x3
#define SWF10_TOGGLE_LIST_4 0x4
#define SWF10_PANNING_EN (1<<23)
#define SWF10_DRIVER_LOADED (1<<22)
#define SWF10_EXTENDED_DESKTOP (1<<21)
#define SWF10_EXCLUSIVE_MODE (1<<20)
#define SWF10_OVERLAY_EN (1<<19)
#define SWF10_PLANEB_HOLDOFF (1<<18)
#define SWF10_PLANEA_HOLDOFF (1<<17)
#define SWF10_VGA_HOLDOFF (1<<16)
#define SWF10_ACTIVE_DISP_MASK 0xffff
#define SWF10_PIPEB_LFP2 (1<<15)
#define SWF10_PIPEB_EFP2 (1<<14)
#define SWF10_PIPEB_TV2 (1<<13)
#define SWF10_PIPEB_CRT2 (1<<12)
#define SWF10_PIPEB_LFP (1<<11)
#define SWF10_PIPEB_EFP (1<<10)
#define SWF10_PIPEB_TV (1<<9)
#define SWF10_PIPEB_CRT (1<<8)
#define SWF10_PIPEA_LFP2 (1<<7)
#define SWF10_PIPEA_EFP2 (1<<6)
#define SWF10_PIPEA_TV2 (1<<5)
#define SWF10_PIPEA_CRT2 (1<<4)
#define SWF10_PIPEA_LFP (1<<3)
#define SWF10_PIPEA_EFP (1<<2)
#define SWF10_PIPEA_TV (1<<1)
#define SWF10_PIPEA_CRT (1<<0)
#define SWF11_MEMORY_SIZE_SHIFT 16
#define SWF11_SV_TEST_EN (1<<15)
#define SWF11_IS_AGP (1<<14)
#define SWF11_DISPLAY_HOLDOFF (1<<13)
#define SWF11_DPMS_REDUCED (1<<12)
#define SWF11_IS_VBE_MODE (1<<11)
#define SWF11_PIPEB_ACCESS (1<<10) /* 0 here means pipe a */
#define SWF11_DPMS_MASK 0x07
#define SWF11_DPMS_OFF (1<<2)
#define SWF11_DPMS_SUSPEND (1<<1)
#define SWF11_DPMS_STANDBY (1<<0)
#define SWF11_DPMS_ON 0
#define SWF14_GFX_PFIT_EN (1<<31)
#define SWF14_TEXT_PFIT_EN (1<<30)
#define SWF14_LID_STATUS_CLOSED (1<<29) /* 0 here means open */
#define SWF14_POPUP_EN (1<<28)
#define SWF14_DISPLAY_HOLDOFF (1<<27)
#define SWF14_DISP_DETECT_EN (1<<26)
#define SWF14_DOCKING_STATUS_DOCKED (1<<25) /* 0 here means undocked */
#define SWF14_DRIVER_STATUS (1<<24)
#define SWF14_OS_TYPE_WIN9X (1<<23)
#define SWF14_OS_TYPE_WINNT (1<<22)
/* 21:19 rsvd */
#define SWF14_PM_TYPE_MASK 0x00070000
#define SWF14_PM_ACPI_VIDEO (0x4 << 16)
#define SWF14_PM_ACPI (0x3 << 16)
#define SWF14_PM_APM_12 (0x2 << 16)
#define SWF14_PM_APM_11 (0x1 << 16)
#define SWF14_HK_REQUEST_MASK 0x0000ffff /* see GR18 6:3 for event type */
/* if GR18 indicates a display switch */
#define SWF14_DS_PIPEB_LFP2_EN (1<<15)
#define SWF14_DS_PIPEB_EFP2_EN (1<<14)
#define SWF14_DS_PIPEB_TV2_EN (1<<13)
#define SWF14_DS_PIPEB_CRT2_EN (1<<12)
#define SWF14_DS_PIPEB_LFP_EN (1<<11)
#define SWF14_DS_PIPEB_EFP_EN (1<<10)
#define SWF14_DS_PIPEB_TV_EN (1<<9)
#define SWF14_DS_PIPEB_CRT_EN (1<<8)
#define SWF14_DS_PIPEA_LFP2_EN (1<<7)
#define SWF14_DS_PIPEA_EFP2_EN (1<<6)
#define SWF14_DS_PIPEA_TV2_EN (1<<5)
#define SWF14_DS_PIPEA_CRT2_EN (1<<4)
#define SWF14_DS_PIPEA_LFP_EN (1<<3)
#define SWF14_DS_PIPEA_EFP_EN (1<<2)
#define SWF14_DS_PIPEA_TV_EN (1<<1)
#define SWF14_DS_PIPEA_CRT_EN (1<<0)
/* if GR18 indicates a panel fitting request */
#define SWF14_PFIT_EN (1<<0) /* 0 means disable */
/* if GR18 indicates an APM change request */
#define SWF14_APM_HIBERNATE 0x4
#define SWF14_APM_SUSPEND 0x3
#define SWF14_APM_STANDBY 0x1
#define SWF14_APM_RESTORE 0x0
/* Add the device class for LFP, TV, HDMI */
#define DEVICE_TYPE_INT_LFP 0x1022
#define DEVICE_TYPE_INT_TV 0x1009
#define DEVICE_TYPE_HDMI 0x60D2
#define DEVICE_TYPE_DP 0x68C6
#define DEVICE_TYPE_eDP 0x78C6
/* define the DVO port for HDMI output type */
#define DVO_B 1
#define DVO_C 2
#define DVO_D 3
/* define the PORT for DP output type */
#define PORT_IDPB 7
#define PORT_IDPC 8
#define PORT_IDPD 9
#endif /* _I830_BIOS_H_ */