1
0
Fork 0
alistair23-linux/drivers/usb/musb/musb_cppi41.c

814 lines
21 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0
#include <linux/device.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
#include <linux/sizes.h>
#include <linux/platform_device.h>
#include <linux/of.h>
#include "cppi_dma.h"
#include "musb_core.h"
#include "musb_trace.h"
#define RNDIS_REG(x) (0x80 + ((x - 1) * 4))
#define EP_MODE_AUTOREQ_NONE 0
#define EP_MODE_AUTOREQ_ALL_NEOP 1
#define EP_MODE_AUTOREQ_ALWAYS 3
#define EP_MODE_DMA_TRANSPARENT 0
#define EP_MODE_DMA_RNDIS 1
#define EP_MODE_DMA_GEN_RNDIS 3
#define USB_CTRL_TX_MODE 0x70
#define USB_CTRL_RX_MODE 0x74
#define USB_CTRL_AUTOREQ 0xd0
#define USB_TDOWN 0xd8
#define MUSB_DMA_NUM_CHANNELS 15
#define DA8XX_USB_MODE 0x10
#define DA8XX_USB_AUTOREQ 0x14
#define DA8XX_USB_TEARDOWN 0x1c
#define DA8XX_DMA_NUM_CHANNELS 4
struct cppi41_dma_controller {
struct dma_controller controller;
struct cppi41_dma_channel *rx_channel;
struct cppi41_dma_channel *tx_channel;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
struct hrtimer early_tx;
struct list_head early_tx_list;
u32 rx_mode;
u32 tx_mode;
u32 auto_req;
u32 tdown_reg;
u32 autoreq_reg;
void (*set_dma_mode)(struct cppi41_dma_channel *cppi41_channel,
unsigned int mode);
u8 num_channels;
};
static void save_rx_toggle(struct cppi41_dma_channel *cppi41_channel)
{
u16 csr;
u8 toggle;
if (cppi41_channel->is_tx)
return;
if (!is_host_active(cppi41_channel->controller->controller.musb))
return;
csr = musb_readw(cppi41_channel->hw_ep->regs, MUSB_RXCSR);
toggle = csr & MUSB_RXCSR_H_DATATOGGLE ? 1 : 0;
cppi41_channel->usb_toggle = toggle;
}
static void update_rx_toggle(struct cppi41_dma_channel *cppi41_channel)
{
struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep;
struct musb *musb = hw_ep->musb;
u16 csr;
u8 toggle;
if (cppi41_channel->is_tx)
return;
if (!is_host_active(musb))
return;
musb_ep_select(musb->mregs, hw_ep->epnum);
csr = musb_readw(hw_ep->regs, MUSB_RXCSR);
toggle = csr & MUSB_RXCSR_H_DATATOGGLE ? 1 : 0;
/*
* AM335x Advisory 1.0.13: Due to internal synchronisation error the
* data toggle may reset from DATA1 to DATA0 during receiving data from
* more than one endpoint.
*/
if (!toggle && toggle == cppi41_channel->usb_toggle) {
csr |= MUSB_RXCSR_H_DATATOGGLE | MUSB_RXCSR_H_WR_DATATOGGLE;
musb_writew(cppi41_channel->hw_ep->regs, MUSB_RXCSR, csr);
musb_dbg(musb, "Restoring DATA1 toggle.");
}
cppi41_channel->usb_toggle = toggle;
}
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
static bool musb_is_tx_fifo_empty(struct musb_hw_ep *hw_ep)
{
u8 epnum = hw_ep->epnum;
struct musb *musb = hw_ep->musb;
void __iomem *epio = musb->endpoints[epnum].regs;
u16 csr;
musb_ep_select(musb->mregs, hw_ep->epnum);
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
csr = musb_readw(epio, MUSB_TXCSR);
if (csr & MUSB_TXCSR_TXPKTRDY)
return false;
return true;
}
static void cppi41_dma_callback(void *private_data,
const struct dmaengine_result *result);
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
static void cppi41_trans_done(struct cppi41_dma_channel *cppi41_channel)
{
struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep;
struct musb *musb = hw_ep->musb;
void __iomem *epio = hw_ep->regs;
u16 csr;
if (!cppi41_channel->prog_len ||
(cppi41_channel->channel.status == MUSB_DMA_STATUS_FREE)) {
/* done, complete */
cppi41_channel->channel.actual_len =
cppi41_channel->transferred;
cppi41_channel->channel.status = MUSB_DMA_STATUS_FREE;
cppi41_channel->channel.rx_packet_done = true;
/*
* transmit ZLP using PIO mode for transfers which size is
* multiple of EP packet size.
*/
if (cppi41_channel->tx_zlp && (cppi41_channel->transferred %
cppi41_channel->packet_sz) == 0) {
musb_ep_select(musb->mregs, hw_ep->epnum);
csr = MUSB_TXCSR_MODE | MUSB_TXCSR_TXPKTRDY;
musb_writew(epio, MUSB_TXCSR, csr);
}
trace_musb_cppi41_done(cppi41_channel);
musb_dma_completion(musb, hw_ep->epnum, cppi41_channel->is_tx);
} else {
/* next iteration, reload */
struct dma_chan *dc = cppi41_channel->dc;
struct dma_async_tx_descriptor *dma_desc;
enum dma_transfer_direction direction;
u32 remain_bytes;
cppi41_channel->buf_addr += cppi41_channel->packet_sz;
remain_bytes = cppi41_channel->total_len;
remain_bytes -= cppi41_channel->transferred;
remain_bytes = min(remain_bytes, cppi41_channel->packet_sz);
cppi41_channel->prog_len = remain_bytes;
direction = cppi41_channel->is_tx ? DMA_MEM_TO_DEV
: DMA_DEV_TO_MEM;
dma_desc = dmaengine_prep_slave_single(dc,
cppi41_channel->buf_addr,
remain_bytes,
direction,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (WARN_ON(!dma_desc))
return;
dma_desc->callback_result = cppi41_dma_callback;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
dma_desc->callback_param = &cppi41_channel->channel;
cppi41_channel->cookie = dma_desc->tx_submit(dma_desc);
trace_musb_cppi41_cont(cppi41_channel);
dma_async_issue_pending(dc);
if (!cppi41_channel->is_tx) {
musb_ep_select(musb->mregs, hw_ep->epnum);
csr = musb_readw(epio, MUSB_RXCSR);
csr |= MUSB_RXCSR_H_REQPKT;
musb_writew(epio, MUSB_RXCSR, csr);
}
}
}
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
static enum hrtimer_restart cppi41_recheck_tx_req(struct hrtimer *timer)
{
struct cppi41_dma_controller *controller;
struct cppi41_dma_channel *cppi41_channel, *n;
struct musb *musb;
unsigned long flags;
enum hrtimer_restart ret = HRTIMER_NORESTART;
controller = container_of(timer, struct cppi41_dma_controller,
early_tx);
musb = controller->controller.musb;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
spin_lock_irqsave(&musb->lock, flags);
list_for_each_entry_safe(cppi41_channel, n, &controller->early_tx_list,
tx_check) {
bool empty;
struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep;
empty = musb_is_tx_fifo_empty(hw_ep);
if (empty) {
list_del_init(&cppi41_channel->tx_check);
cppi41_trans_done(cppi41_channel);
}
}
if (!list_empty(&controller->early_tx_list) &&
!hrtimer_is_queued(&controller->early_tx)) {
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
ret = HRTIMER_RESTART;
hrtimer_forward_now(&controller->early_tx, 20 * NSEC_PER_USEC);
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
}
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
}
static void cppi41_dma_callback(void *private_data,
const struct dmaengine_result *result)
{
struct dma_channel *channel = private_data;
struct cppi41_dma_channel *cppi41_channel = channel->private_data;
struct musb_hw_ep *hw_ep = cppi41_channel->hw_ep;
struct cppi41_dma_controller *controller;
struct musb *musb = hw_ep->musb;
unsigned long flags;
struct dma_tx_state txstate;
u32 transferred;
int is_hs = 0;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
bool empty;
controller = cppi41_channel->controller;
if (controller->controller.dma_callback)
controller->controller.dma_callback(&controller->controller);
if (result->result == DMA_TRANS_ABORTED)
return;
spin_lock_irqsave(&musb->lock, flags);
dmaengine_tx_status(cppi41_channel->dc, cppi41_channel->cookie,
&txstate);
transferred = cppi41_channel->prog_len - txstate.residue;
cppi41_channel->transferred += transferred;
trace_musb_cppi41_gb(cppi41_channel);
update_rx_toggle(cppi41_channel);
if (cppi41_channel->transferred == cppi41_channel->total_len ||
transferred < cppi41_channel->packet_sz)
cppi41_channel->prog_len = 0;
if (cppi41_channel->is_tx) {
u8 type;
if (is_host_active(musb))
type = hw_ep->out_qh->type;
else
type = hw_ep->ep_in.type;
if (type == USB_ENDPOINT_XFER_ISOC)
/*
* Don't use the early-TX-interrupt workaround below
* for Isoch transfter. Since Isoch are periodic
* transfer, by the time the next transfer is
* scheduled, the current one should be done already.
*
* This avoids audio playback underrun issue.
*/
empty = true;
else
empty = musb_is_tx_fifo_empty(hw_ep);
}
if (!cppi41_channel->is_tx || empty) {
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
cppi41_trans_done(cppi41_channel);
goto out;
}
/*
* On AM335x it has been observed that the TX interrupt fires
* too early that means the TXFIFO is not yet empty but the DMA
* engine says that it is done with the transfer. We don't
* receive a FIFO empty interrupt so the only thing we can do is
* to poll for the bit. On HS it usually takes 2us, on FS around
* 110us - 150us depending on the transfer size.
* We spin on HS (no longer than than 25us and setup a timer on
* FS to check for the bit and complete the transfer.
*/
if (is_host_active(musb)) {
if (musb->port1_status & USB_PORT_STAT_HIGH_SPEED)
is_hs = 1;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
} else {
if (musb->g.speed == USB_SPEED_HIGH)
is_hs = 1;
}
if (is_hs) {
unsigned wait = 25;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
do {
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
empty = musb_is_tx_fifo_empty(hw_ep);
if (empty) {
cppi41_trans_done(cppi41_channel);
goto out;
}
wait--;
if (!wait)
break;
cpu_relax();
} while (1);
}
list_add_tail(&cppi41_channel->tx_check,
&controller->early_tx_list);
if (!hrtimer_is_queued(&controller->early_tx)) {
unsigned long usecs = cppi41_channel->total_len / 10;
2014-06-19 16:20:44 -06:00
hrtimer_start_range_ns(&controller->early_tx,
usecs * NSEC_PER_USEC,
20 * NSEC_PER_USEC,
HRTIMER_MODE_REL);
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
}
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
out:
spin_unlock_irqrestore(&musb->lock, flags);
}
static u32 update_ep_mode(unsigned ep, unsigned mode, u32 old)
{
unsigned shift;
shift = (ep - 1) * 2;
old &= ~(3 << shift);
old |= mode << shift;
return old;
}
static void cppi41_set_dma_mode(struct cppi41_dma_channel *cppi41_channel,
unsigned mode)
{
struct cppi41_dma_controller *controller = cppi41_channel->controller;
struct musb *musb = controller->controller.musb;
u32 port;
u32 new_mode;
u32 old_mode;
if (cppi41_channel->is_tx)
old_mode = controller->tx_mode;
else
old_mode = controller->rx_mode;
port = cppi41_channel->port_num;
new_mode = update_ep_mode(port, mode, old_mode);
if (new_mode == old_mode)
return;
if (cppi41_channel->is_tx) {
controller->tx_mode = new_mode;
musb_writel(musb->ctrl_base, USB_CTRL_TX_MODE, new_mode);
} else {
controller->rx_mode = new_mode;
musb_writel(musb->ctrl_base, USB_CTRL_RX_MODE, new_mode);
}
}
static void da8xx_set_dma_mode(struct cppi41_dma_channel *cppi41_channel,
unsigned int mode)
{
struct cppi41_dma_controller *controller = cppi41_channel->controller;
struct musb *musb = controller->controller.musb;
unsigned int shift;
u32 port;
u32 new_mode;
u32 old_mode;
old_mode = controller->tx_mode;
port = cppi41_channel->port_num;
shift = (port - 1) * 4;
if (!cppi41_channel->is_tx)
shift += 16;
new_mode = old_mode & ~(3 << shift);
new_mode |= mode << shift;
if (new_mode == old_mode)
return;
controller->tx_mode = new_mode;
musb_writel(musb->ctrl_base, DA8XX_USB_MODE, new_mode);
}
static void cppi41_set_autoreq_mode(struct cppi41_dma_channel *cppi41_channel,
unsigned mode)
{
struct cppi41_dma_controller *controller = cppi41_channel->controller;
u32 port;
u32 new_mode;
u32 old_mode;
old_mode = controller->auto_req;
port = cppi41_channel->port_num;
new_mode = update_ep_mode(port, mode, old_mode);
if (new_mode == old_mode)
return;
controller->auto_req = new_mode;
musb_writel(controller->controller.musb->ctrl_base,
controller->autoreq_reg, new_mode);
}
static bool cppi41_configure_channel(struct dma_channel *channel,
u16 packet_sz, u8 mode,
dma_addr_t dma_addr, u32 len)
{
struct cppi41_dma_channel *cppi41_channel = channel->private_data;
struct cppi41_dma_controller *controller = cppi41_channel->controller;
struct dma_chan *dc = cppi41_channel->dc;
struct dma_async_tx_descriptor *dma_desc;
enum dma_transfer_direction direction;
struct musb *musb = cppi41_channel->controller->controller.musb;
unsigned use_gen_rndis = 0;
cppi41_channel->buf_addr = dma_addr;
cppi41_channel->total_len = len;
cppi41_channel->transferred = 0;
cppi41_channel->packet_sz = packet_sz;
cppi41_channel->tx_zlp = (cppi41_channel->is_tx && mode) ? 1 : 0;
/*
* Due to AM335x' Advisory 1.0.13 we are not allowed to transfer more
* than max packet size at a time.
*/
if (cppi41_channel->is_tx)
use_gen_rndis = 1;
if (use_gen_rndis) {
/* RNDIS mode */
if (len > packet_sz) {
musb_writel(musb->ctrl_base,
RNDIS_REG(cppi41_channel->port_num), len);
/* gen rndis */
controller->set_dma_mode(cppi41_channel,
EP_MODE_DMA_GEN_RNDIS);
/* auto req */
cppi41_set_autoreq_mode(cppi41_channel,
EP_MODE_AUTOREQ_ALL_NEOP);
} else {
musb_writel(musb->ctrl_base,
RNDIS_REG(cppi41_channel->port_num), 0);
controller->set_dma_mode(cppi41_channel,
EP_MODE_DMA_TRANSPARENT);
cppi41_set_autoreq_mode(cppi41_channel,
EP_MODE_AUTOREQ_NONE);
}
} else {
/* fallback mode */
controller->set_dma_mode(cppi41_channel,
EP_MODE_DMA_TRANSPARENT);
cppi41_set_autoreq_mode(cppi41_channel, EP_MODE_AUTOREQ_NONE);
len = min_t(u32, packet_sz, len);
}
cppi41_channel->prog_len = len;
direction = cppi41_channel->is_tx ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
dma_desc = dmaengine_prep_slave_single(dc, dma_addr, len, direction,
DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
if (!dma_desc)
return false;
dma_desc->callback_result = cppi41_dma_callback;
dma_desc->callback_param = channel;
cppi41_channel->cookie = dma_desc->tx_submit(dma_desc);
cppi41_channel->channel.rx_packet_done = false;
trace_musb_cppi41_config(cppi41_channel);
save_rx_toggle(cppi41_channel);
dma_async_issue_pending(dc);
return true;
}
static struct dma_channel *cppi41_dma_channel_allocate(struct dma_controller *c,
struct musb_hw_ep *hw_ep, u8 is_tx)
{
struct cppi41_dma_controller *controller = container_of(c,
struct cppi41_dma_controller, controller);
struct cppi41_dma_channel *cppi41_channel = NULL;
u8 ch_num = hw_ep->epnum - 1;
if (ch_num >= controller->num_channels)
return NULL;
if (is_tx)
cppi41_channel = &controller->tx_channel[ch_num];
else
cppi41_channel = &controller->rx_channel[ch_num];
if (!cppi41_channel->dc)
return NULL;
if (cppi41_channel->is_allocated)
return NULL;
cppi41_channel->hw_ep = hw_ep;
cppi41_channel->is_allocated = 1;
trace_musb_cppi41_alloc(cppi41_channel);
return &cppi41_channel->channel;
}
static void cppi41_dma_channel_release(struct dma_channel *channel)
{
struct cppi41_dma_channel *cppi41_channel = channel->private_data;
trace_musb_cppi41_free(cppi41_channel);
if (cppi41_channel->is_allocated) {
cppi41_channel->is_allocated = 0;
channel->status = MUSB_DMA_STATUS_FREE;
channel->actual_len = 0;
}
}
static int cppi41_dma_channel_program(struct dma_channel *channel,
u16 packet_sz, u8 mode,
dma_addr_t dma_addr, u32 len)
{
int ret;
struct cppi41_dma_channel *cppi41_channel = channel->private_data;
int hb_mult = 0;
BUG_ON(channel->status == MUSB_DMA_STATUS_UNKNOWN ||
channel->status == MUSB_DMA_STATUS_BUSY);
if (is_host_active(cppi41_channel->controller->controller.musb)) {
if (cppi41_channel->is_tx)
hb_mult = cppi41_channel->hw_ep->out_qh->hb_mult;
else
hb_mult = cppi41_channel->hw_ep->in_qh->hb_mult;
}
channel->status = MUSB_DMA_STATUS_BUSY;
channel->actual_len = 0;
if (hb_mult)
packet_sz = hb_mult * (packet_sz & 0x7FF);
ret = cppi41_configure_channel(channel, packet_sz, mode, dma_addr, len);
if (!ret)
channel->status = MUSB_DMA_STATUS_FREE;
return ret;
}
static int cppi41_is_compatible(struct dma_channel *channel, u16 maxpacket,
void *buf, u32 length)
{
struct cppi41_dma_channel *cppi41_channel = channel->private_data;
struct cppi41_dma_controller *controller = cppi41_channel->controller;
struct musb *musb = controller->controller.musb;
if (is_host_active(musb)) {
WARN_ON(1);
return 1;
}
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
if (cppi41_channel->hw_ep->ep_in.type != USB_ENDPOINT_XFER_BULK)
return 0;
if (cppi41_channel->is_tx)
return 1;
/* AM335x Advisory 1.0.13. No workaround for device RX mode */
return 0;
}
static int cppi41_dma_channel_abort(struct dma_channel *channel)
{
struct cppi41_dma_channel *cppi41_channel = channel->private_data;
struct cppi41_dma_controller *controller = cppi41_channel->controller;
struct musb *musb = controller->controller.musb;
void __iomem *epio = cppi41_channel->hw_ep->regs;
int tdbit;
int ret;
unsigned is_tx;
u16 csr;
is_tx = cppi41_channel->is_tx;
trace_musb_cppi41_abort(cppi41_channel);
if (cppi41_channel->channel.status == MUSB_DMA_STATUS_FREE)
return 0;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
list_del_init(&cppi41_channel->tx_check);
if (is_tx) {
csr = musb_readw(epio, MUSB_TXCSR);
csr &= ~MUSB_TXCSR_DMAENAB;
musb_writew(epio, MUSB_TXCSR, csr);
} else {
cppi41_set_autoreq_mode(cppi41_channel, EP_MODE_AUTOREQ_NONE);
/* delay to drain to cppi dma pipeline for isoch */
udelay(250);
csr = musb_readw(epio, MUSB_RXCSR);
csr &= ~(MUSB_RXCSR_H_REQPKT | MUSB_RXCSR_DMAENAB);
musb_writew(epio, MUSB_RXCSR, csr);
/* wait to drain cppi dma pipe line */
udelay(50);
csr = musb_readw(epio, MUSB_RXCSR);
if (csr & MUSB_RXCSR_RXPKTRDY) {
csr |= MUSB_RXCSR_FLUSHFIFO;
musb_writew(epio, MUSB_RXCSR, csr);
musb_writew(epio, MUSB_RXCSR, csr);
}
}
/* DA8xx Advisory 2.3.27: wait 250 ms before to start the teardown */
if (musb->ops->quirks & MUSB_DA8XX)
mdelay(250);
tdbit = 1 << cppi41_channel->port_num;
if (is_tx)
tdbit <<= 16;
do {
if (is_tx)
musb_writel(musb->ctrl_base, controller->tdown_reg,
tdbit);
ret = dmaengine_terminate_all(cppi41_channel->dc);
} while (ret == -EAGAIN);
if (is_tx) {
musb_writel(musb->ctrl_base, controller->tdown_reg, tdbit);
csr = musb_readw(epio, MUSB_TXCSR);
if (csr & MUSB_TXCSR_TXPKTRDY) {
csr |= MUSB_TXCSR_FLUSHFIFO;
musb_writew(epio, MUSB_TXCSR, csr);
}
}
cppi41_channel->channel.status = MUSB_DMA_STATUS_FREE;
return 0;
}
static void cppi41_release_all_dma_chans(struct cppi41_dma_controller *ctrl)
{
struct dma_chan *dc;
int i;
for (i = 0; i < ctrl->num_channels; i++) {
dc = ctrl->tx_channel[i].dc;
if (dc)
dma_release_channel(dc);
dc = ctrl->rx_channel[i].dc;
if (dc)
dma_release_channel(dc);
}
}
static void cppi41_dma_controller_stop(struct cppi41_dma_controller *controller)
{
cppi41_release_all_dma_chans(controller);
}
static int cppi41_dma_controller_start(struct cppi41_dma_controller *controller)
{
struct musb *musb = controller->controller.musb;
struct device *dev = musb->controller;
struct device_node *np = dev->parent->of_node;
struct cppi41_dma_channel *cppi41_channel;
int count;
int i;
int ret;
count = of_property_count_strings(np, "dma-names");
if (count < 0)
return count;
for (i = 0; i < count; i++) {
struct dma_chan *dc;
struct dma_channel *musb_dma;
const char *str;
unsigned is_tx;
unsigned int port;
ret = of_property_read_string_index(np, "dma-names", i, &str);
if (ret)
goto err;
if (strstarts(str, "tx"))
is_tx = 1;
else if (strstarts(str, "rx"))
is_tx = 0;
else {
dev_err(dev, "Wrong dmatype %s\n", str);
goto err;
}
ret = kstrtouint(str + 2, 0, &port);
if (ret)
goto err;
ret = -EINVAL;
if (port > controller->num_channels || !port)
goto err;
if (is_tx)
cppi41_channel = &controller->tx_channel[port - 1];
else
cppi41_channel = &controller->rx_channel[port - 1];
cppi41_channel->controller = controller;
cppi41_channel->port_num = port;
cppi41_channel->is_tx = is_tx;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
INIT_LIST_HEAD(&cppi41_channel->tx_check);
musb_dma = &cppi41_channel->channel;
musb_dma->private_data = cppi41_channel;
musb_dma->status = MUSB_DMA_STATUS_FREE;
musb_dma->max_len = SZ_4M;
dc = dma_request_chan(dev->parent, str);
if (IS_ERR(dc)) {
ret = PTR_ERR(dc);
if (ret != -EPROBE_DEFER)
dev_err(dev, "Failed to request %s: %d.\n",
str, ret);
goto err;
}
cppi41_channel->dc = dc;
}
return 0;
err:
cppi41_release_all_dma_chans(controller);
return ret;
}
void cppi41_dma_controller_destroy(struct dma_controller *c)
{
struct cppi41_dma_controller *controller = container_of(c,
struct cppi41_dma_controller, controller);
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
hrtimer_cancel(&controller->early_tx);
cppi41_dma_controller_stop(controller);
kfree(controller->rx_channel);
kfree(controller->tx_channel);
kfree(controller);
}
EXPORT_SYMBOL_GPL(cppi41_dma_controller_destroy);
struct dma_controller *
cppi41_dma_controller_create(struct musb *musb, void __iomem *base)
{
struct cppi41_dma_controller *controller;
int channel_size;
int ret = 0;
if (!musb->controller->parent->of_node) {
dev_err(musb->controller, "Need DT for the DMA engine.\n");
return NULL;
}
controller = kzalloc(sizeof(*controller), GFP_KERNEL);
if (!controller)
goto kzalloc_fail;
usb: musb: musb_cppi41: handle pre-mature TX complete interrupt The TX-complete interrupt of the CPPI41 on AM335x fires too early. Adding a loop and counting how long it takes until the MUSB_TXCSR_TXPKTRDY bit is cleared I see FS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1 |cppi41_dma_callback() 74 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1 |cppi41_dma_callback() 66 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1 |cppi41_dma_callback() 136 loops avg: 110 - 150us HS: |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1 |cppi41_dma_callback() 0 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1 |cppi41_dma_callback() 2 loops |musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1 |cppi41_dma_callback() 13 loops avg: 2us for the same test case. One loop means a udelay(1). The delay seems to depend on the packet size. On HS the bit is always cleared for small packet sizes while on FS it is never the case, it mostly around 110us. This testing has been performed with g_ether (musb as device) and using BULK transfers. INTR transfers are way more fun: during init the gadget sends a INT packet to the host and cppi41 says "transfer done" shortly after. The MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host did not try to receive it, it does so after the interface (on host side) has been configured. Until this happens, that packet remains in musb's FIFO. To fix this, two things are done: - No DMA transfers for INT based endpoints. These transfer are usually very small and rare so it is likely better to skip the DMA engine and stuff the four bytes directly into the FIFO - on HS we poll up to 25us and hope that bit goes away. If not we setup a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS the command | ping 10.10.10.10 -c1 -s65130 creates about 44 1514bytes transfers. About 19 of them need a second timer to complete. Reported-by: Bin Liu <b-liu@ti.com> Cc: stable@vger.kernel.org Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-12 08:37:47 -07:00
hrtimer_init(&controller->early_tx, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
controller->early_tx.function = cppi41_recheck_tx_req;
INIT_LIST_HEAD(&controller->early_tx_list);
controller->controller.channel_alloc = cppi41_dma_channel_allocate;
controller->controller.channel_release = cppi41_dma_channel_release;
controller->controller.channel_program = cppi41_dma_channel_program;
controller->controller.channel_abort = cppi41_dma_channel_abort;
controller->controller.is_compatible = cppi41_is_compatible;
controller->controller.musb = musb;
if (musb->ops->quirks & MUSB_DA8XX) {
controller->tdown_reg = DA8XX_USB_TEARDOWN;
controller->autoreq_reg = DA8XX_USB_AUTOREQ;
controller->set_dma_mode = da8xx_set_dma_mode;
controller->num_channels = DA8XX_DMA_NUM_CHANNELS;
} else {
controller->tdown_reg = USB_TDOWN;
controller->autoreq_reg = USB_CTRL_AUTOREQ;
controller->set_dma_mode = cppi41_set_dma_mode;
controller->num_channels = MUSB_DMA_NUM_CHANNELS;
}
channel_size = controller->num_channels *
sizeof(struct cppi41_dma_channel);
controller->rx_channel = kzalloc(channel_size, GFP_KERNEL);
if (!controller->rx_channel)
goto rx_channel_alloc_fail;
controller->tx_channel = kzalloc(channel_size, GFP_KERNEL);
if (!controller->tx_channel)
goto tx_channel_alloc_fail;
ret = cppi41_dma_controller_start(controller);
if (ret)
goto plat_get_fail;
return &controller->controller;
plat_get_fail:
kfree(controller->tx_channel);
tx_channel_alloc_fail:
kfree(controller->rx_channel);
rx_channel_alloc_fail:
kfree(controller);
kzalloc_fail:
if (ret == -EPROBE_DEFER)
return ERR_PTR(ret);
return NULL;
}
EXPORT_SYMBOL_GPL(cppi41_dma_controller_create);