alistair23-linux/sound/soc/omap/omap-mcbsp.c

601 lines
17 KiB
C
Raw Normal View History

/*
* omap-mcbsp.c -- OMAP ALSA SoC DAI driver using McBSP port
*
* Copyright (C) 2008 Nokia Corporation
*
* Contact: Jarkko Nikula <jhnikula@gmail.com>
* Peter Ujfalusi <peter.ujfalusi@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/device.h>
#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
#include <sound/initval.h>
#include <sound/soc.h>
#include <mach/control.h>
#include <mach/dma.h>
#include <mach/mcbsp.h>
#include "omap-mcbsp.h"
#include "omap-pcm.h"
#define OMAP_MCBSP_RATES (SNDRV_PCM_RATE_8000_96000)
struct omap_mcbsp_data {
unsigned int bus_id;
struct omap_mcbsp_reg_cfg regs;
unsigned int fmt;
/*
* Flags indicating is the bus already activated and configured by
* another substream
*/
int active;
int configured;
};
#define to_mcbsp(priv) container_of((priv), struct omap_mcbsp_data, bus_id)
static struct omap_mcbsp_data mcbsp_data[NUM_LINKS];
/*
* Stream DMA parameters. DMA request line and port address are set runtime
* since they are different between OMAP1 and later OMAPs
*/
static struct omap_pcm_dma_data omap_mcbsp_dai_dma_params[NUM_LINKS][2];
#if defined(CONFIG_ARCH_OMAP15XX) || defined(CONFIG_ARCH_OMAP16XX)
static const int omap1_dma_reqs[][2] = {
{ OMAP_DMA_MCBSP1_TX, OMAP_DMA_MCBSP1_RX },
{ OMAP_DMA_MCBSP2_TX, OMAP_DMA_MCBSP2_RX },
{ OMAP_DMA_MCBSP3_TX, OMAP_DMA_MCBSP3_RX },
};
static const unsigned long omap1_mcbsp_port[][2] = {
{ OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DXR1,
OMAP1510_MCBSP1_BASE + OMAP_MCBSP_REG_DRR1 },
{ OMAP1510_MCBSP2_BASE + OMAP_MCBSP_REG_DXR1,
OMAP1510_MCBSP2_BASE + OMAP_MCBSP_REG_DRR1 },
{ OMAP1510_MCBSP3_BASE + OMAP_MCBSP_REG_DXR1,
OMAP1510_MCBSP3_BASE + OMAP_MCBSP_REG_DRR1 },
};
#else
static const int omap1_dma_reqs[][2] = {};
static const unsigned long omap1_mcbsp_port[][2] = {};
#endif
#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
static const int omap24xx_dma_reqs[][2] = {
{ OMAP24XX_DMA_MCBSP1_TX, OMAP24XX_DMA_MCBSP1_RX },
{ OMAP24XX_DMA_MCBSP2_TX, OMAP24XX_DMA_MCBSP2_RX },
#if defined(CONFIG_ARCH_OMAP2430) || defined(CONFIG_ARCH_OMAP34XX)
{ OMAP24XX_DMA_MCBSP3_TX, OMAP24XX_DMA_MCBSP3_RX },
{ OMAP24XX_DMA_MCBSP4_TX, OMAP24XX_DMA_MCBSP4_RX },
{ OMAP24XX_DMA_MCBSP5_TX, OMAP24XX_DMA_MCBSP5_RX },
#endif
};
#else
static const int omap24xx_dma_reqs[][2] = {};
#endif
#if defined(CONFIG_ARCH_OMAP2420)
static const unsigned long omap2420_mcbsp_port[][2] = {
{ OMAP24XX_MCBSP1_BASE + OMAP_MCBSP_REG_DXR1,
OMAP24XX_MCBSP1_BASE + OMAP_MCBSP_REG_DRR1 },
{ OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DXR1,
OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DRR1 },
};
#else
static const unsigned long omap2420_mcbsp_port[][2] = {};
#endif
#if defined(CONFIG_ARCH_OMAP2430)
static const unsigned long omap2430_mcbsp_port[][2] = {
{ OMAP24XX_MCBSP1_BASE + OMAP_MCBSP_REG_DXR,
OMAP24XX_MCBSP1_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DXR,
OMAP24XX_MCBSP2_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP2430_MCBSP3_BASE + OMAP_MCBSP_REG_DXR,
OMAP2430_MCBSP3_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP2430_MCBSP4_BASE + OMAP_MCBSP_REG_DXR,
OMAP2430_MCBSP4_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP2430_MCBSP5_BASE + OMAP_MCBSP_REG_DXR,
OMAP2430_MCBSP5_BASE + OMAP_MCBSP_REG_DRR },
};
#else
static const unsigned long omap2430_mcbsp_port[][2] = {};
#endif
#if defined(CONFIG_ARCH_OMAP34XX)
static const unsigned long omap34xx_mcbsp_port[][2] = {
{ OMAP34XX_MCBSP1_BASE + OMAP_MCBSP_REG_DXR,
OMAP34XX_MCBSP1_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP34XX_MCBSP2_BASE + OMAP_MCBSP_REG_DXR,
OMAP34XX_MCBSP2_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP34XX_MCBSP3_BASE + OMAP_MCBSP_REG_DXR,
OMAP34XX_MCBSP3_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP34XX_MCBSP4_BASE + OMAP_MCBSP_REG_DXR,
OMAP34XX_MCBSP4_BASE + OMAP_MCBSP_REG_DRR },
{ OMAP34XX_MCBSP5_BASE + OMAP_MCBSP_REG_DXR,
OMAP34XX_MCBSP5_BASE + OMAP_MCBSP_REG_DRR },
};
#else
static const unsigned long omap34xx_mcbsp_port[][2] = {};
#endif
static void omap_mcbsp_set_threshold(struct snd_pcm_substream *substream)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
int samples = snd_pcm_lib_period_bytes(substream) >> 1;
/* Configure McBSP internal buffer usage */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
omap_mcbsp_set_tx_threshold(mcbsp_data->bus_id, samples - 1);
else
omap_mcbsp_set_rx_threshold(mcbsp_data->bus_id, samples - 1);
}
static int omap_mcbsp_dai_startup(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
int bus_id = mcbsp_data->bus_id;
int err = 0;
if (!cpu_dai->active)
err = omap_mcbsp_request(bus_id);
if (cpu_is_omap343x()) {
int max_period;
/*
* McBSP2 in OMAP3 has 1024 * 32-bit internal audio buffer.
* Set constraint for minimum buffer size to the same than FIFO
* size in order to avoid underruns in playback startup because
* HW is keeping the DMA request active until FIFO is filled.
*/
if (bus_id == 1)
snd_pcm_hw_constraint_minmax(substream->runtime,
SNDRV_PCM_HW_PARAM_BUFFER_BYTES,
4096, UINT_MAX);
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
max_period = omap_mcbsp_get_max_tx_threshold(bus_id);
else
max_period = omap_mcbsp_get_max_rx_threshold(bus_id);
max_period++;
max_period <<= 1;
snd_pcm_hw_constraint_minmax(substream->runtime,
SNDRV_PCM_HW_PARAM_PERIOD_BYTES,
32, max_period);
}
return err;
}
static void omap_mcbsp_dai_shutdown(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
if (!cpu_dai->active) {
omap_mcbsp_free(mcbsp_data->bus_id);
mcbsp_data->configured = 0;
}
}
static int omap_mcbsp_dai_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 00:59:47 -06:00
int err = 0, play = (substream->stream == SNDRV_PCM_STREAM_PLAYBACK);
switch (cmd) {
case SNDRV_PCM_TRIGGER_START:
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 00:59:47 -06:00
mcbsp_data->active++;
omap_mcbsp_start(mcbsp_data->bus_id, play, !play);
/* Make sure data transfer is frame synchronized */
if (substream->stream == SNDRV_PCM_STREAM_PLAYBACK)
omap_mcbsp_xmit_enable(mcbsp_data->bus_id, 1);
else
omap_mcbsp_recv_enable(mcbsp_data->bus_id, 1);
break;
case SNDRV_PCM_TRIGGER_STOP:
case SNDRV_PCM_TRIGGER_SUSPEND:
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
ARM: OMAP: McBSP: Fix ASoC on OMAP1510 by fixing API of omap_mcbsp_start/stop Simultaneous audio playback and capture on OMAP1510 can cause that second stream is stalled if there is enough delay between startup of the audio streams. Current implementation of the omap_mcbsp_start is starting both transmitter and receiver at the same time and it is called only for firstly started audio stream from the OMAP McBSP based ASoC DAI driver. Since DMA request lines on OMAP1510 are edge sensitive, the DMA request is missed if there is no DMA transfer set up at that time when the first word after McBSP startup is transmitted. The problem hasn't noted before since later OMAPs are using level sensitive DMA request lines. Fix the problem by changing API of omap_mcbsp_start and omap_mcbsp_stop by allowing to start and stop individually McBSP transmitter and receiver logics. Then call those functions individually for both audio playback and capture streams. This ensures that DMA transfer is setup before transmitter or receiver is started. Thanks to Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> for detailed problem analysis and Peter Ujfalusi <peter.ujfalusi@nokia.com> for info about DMA request line behavior differences between the OMAP generations. Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-08-07 00:59:47 -06:00
omap_mcbsp_stop(mcbsp_data->bus_id, play, !play);
mcbsp_data->active--;
break;
default:
err = -EINVAL;
}
return err;
}
static int omap_mcbsp_dai_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_dai *cpu_dai = rtd->dai->cpu_dai;
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs;
int dma, bus_id = mcbsp_data->bus_id, id = cpu_dai->id;
int wlen, channels, wpf, sync_mode = OMAP_DMA_SYNC_ELEMENT;
unsigned long port;
unsigned int format;
if (cpu_class_is_omap1()) {
dma = omap1_dma_reqs[bus_id][substream->stream];
port = omap1_mcbsp_port[bus_id][substream->stream];
} else if (cpu_is_omap2420()) {
dma = omap24xx_dma_reqs[bus_id][substream->stream];
port = omap2420_mcbsp_port[bus_id][substream->stream];
} else if (cpu_is_omap2430()) {
dma = omap24xx_dma_reqs[bus_id][substream->stream];
port = omap2430_mcbsp_port[bus_id][substream->stream];
} else if (cpu_is_omap343x()) {
dma = omap24xx_dma_reqs[bus_id][substream->stream];
port = omap34xx_mcbsp_port[bus_id][substream->stream];
omap_mcbsp_dai_dma_params[id][substream->stream].set_threshold =
omap_mcbsp_set_threshold;
sync_mode = OMAP_DMA_SYNC_FRAME;
} else {
return -ENODEV;
}
omap_mcbsp_dai_dma_params[id][substream->stream].name =
substream->stream ? "Audio Capture" : "Audio Playback";
omap_mcbsp_dai_dma_params[id][substream->stream].dma_req = dma;
omap_mcbsp_dai_dma_params[id][substream->stream].port_addr = port;
omap_mcbsp_dai_dma_params[id][substream->stream].sync_mode = sync_mode;
cpu_dai->dma_data = &omap_mcbsp_dai_dma_params[id][substream->stream];
if (mcbsp_data->configured) {
/* McBSP already configured by another stream */
return 0;
}
format = mcbsp_data->fmt & SND_SOC_DAIFMT_FORMAT_MASK;
wpf = channels = params_channels(params);
switch (channels) {
case 2:
if (format == SND_SOC_DAIFMT_I2S) {
/* Use dual-phase frames */
regs->rcr2 |= RPHASE;
regs->xcr2 |= XPHASE;
/* Set 1 word per (McBSP) frame for phase1 and phase2 */
wpf--;
regs->rcr2 |= RFRLEN2(wpf - 1);
regs->xcr2 |= XFRLEN2(wpf - 1);
}
case 1:
case 4:
/* Set word per (McBSP) frame for phase1 */
regs->rcr1 |= RFRLEN1(wpf - 1);
regs->xcr1 |= XFRLEN1(wpf - 1);
break;
default:
/* Unsupported number of channels */
return -EINVAL;
}
switch (params_format(params)) {
case SNDRV_PCM_FORMAT_S16_LE:
/* Set word lengths */
wlen = 16;
regs->rcr2 |= RWDLEN2(OMAP_MCBSP_WORD_16);
regs->rcr1 |= RWDLEN1(OMAP_MCBSP_WORD_16);
regs->xcr2 |= XWDLEN2(OMAP_MCBSP_WORD_16);
regs->xcr1 |= XWDLEN1(OMAP_MCBSP_WORD_16);
break;
default:
/* Unsupported PCM format */
return -EINVAL;
}
/* Set FS period and length in terms of bit clock periods */
switch (format) {
case SND_SOC_DAIFMT_I2S:
regs->srgr2 |= FPER(wlen * channels - 1);
regs->srgr1 |= FWID(wlen - 1);
break;
case SND_SOC_DAIFMT_DSP_A:
case SND_SOC_DAIFMT_DSP_B:
regs->srgr2 |= FPER(wlen * channels - 1);
regs->srgr1 |= FWID(0);
break;
}
omap_mcbsp_config(bus_id, &mcbsp_data->regs);
mcbsp_data->configured = 1;
return 0;
}
/*
* This must be called before _set_clkdiv and _set_sysclk since McBSP register
* cache is initialized here
*/
static int omap_mcbsp_dai_set_dai_fmt(struct snd_soc_dai *cpu_dai,
unsigned int fmt)
{
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs;
unsigned int temp_fmt = fmt;
if (mcbsp_data->configured)
return 0;
mcbsp_data->fmt = fmt;
memset(regs, 0, sizeof(*regs));
/* Generic McBSP register settings */
regs->spcr2 |= XINTM(3) | FREE;
regs->spcr1 |= RINTM(3);
/* RFIG and XFIG are not defined in 34xx */
if (!cpu_is_omap34xx()) {
regs->rcr2 |= RFIG;
regs->xcr2 |= XFIG;
}
if (cpu_is_omap2430() || cpu_is_omap34xx()) {
regs->xccr = DXENDLY(1) | XDMAEN;
regs->rccr = RFULL_CYCLE | RDMAEN;
}
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_I2S:
/* 1-bit data delay */
regs->rcr2 |= RDATDLY(1);
regs->xcr2 |= XDATDLY(1);
regs->rccr |= RFULL_CYCLE | RDMAEN | RDISABLE;
regs->xccr |= (DXENDLY(1) | XDMAEN | XDISABLE);
break;
case SND_SOC_DAIFMT_DSP_A:
/* 1-bit data delay */
regs->rcr2 |= RDATDLY(1);
regs->xcr2 |= XDATDLY(1);
regs->rccr |= RFULL_CYCLE | RDMAEN | RDISABLE;
regs->xccr |= (DXENDLY(1) | XDMAEN | XDISABLE);
/* Invert FS polarity configuration */
temp_fmt ^= SND_SOC_DAIFMT_NB_IF;
break;
case SND_SOC_DAIFMT_DSP_B:
/* 0-bit data delay */
regs->rcr2 |= RDATDLY(0);
regs->xcr2 |= XDATDLY(0);
/* Invert FS polarity configuration */
temp_fmt ^= SND_SOC_DAIFMT_NB_IF;
break;
default:
/* Unsupported data format */
return -EINVAL;
}
switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
case SND_SOC_DAIFMT_CBS_CFS:
/* McBSP master. Set FS and bit clocks as outputs */
regs->pcr0 |= FSXM | FSRM |
CLKXM | CLKRM;
/* Sample rate generator drives the FS */
regs->srgr2 |= FSGM;
break;
case SND_SOC_DAIFMT_CBM_CFM:
/* McBSP slave */
break;
default:
/* Unsupported master/slave configuration */
return -EINVAL;
}
/* Set bit clock (CLKX/CLKR) and FS polarities */
switch (temp_fmt & SND_SOC_DAIFMT_INV_MASK) {
case SND_SOC_DAIFMT_NB_NF:
/*
* Normal BCLK + FS.
* FS active low. TX data driven on falling edge of bit clock
* and RX data sampled on rising edge of bit clock.
*/
regs->pcr0 |= FSXP | FSRP |
CLKXP | CLKRP;
break;
case SND_SOC_DAIFMT_NB_IF:
regs->pcr0 |= CLKXP | CLKRP;
break;
case SND_SOC_DAIFMT_IB_NF:
regs->pcr0 |= FSXP | FSRP;
break;
case SND_SOC_DAIFMT_IB_IF:
break;
default:
return -EINVAL;
}
return 0;
}
static int omap_mcbsp_dai_set_clkdiv(struct snd_soc_dai *cpu_dai,
int div_id, int div)
{
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs;
if (div_id != OMAP_MCBSP_CLKGDV)
return -ENODEV;
regs->srgr1 |= CLKGDV(div - 1);
return 0;
}
static int omap_mcbsp_dai_set_clks_src(struct omap_mcbsp_data *mcbsp_data,
int clk_id)
{
int sel_bit;
u16 reg, reg_devconf1 = OMAP243X_CONTROL_DEVCONF1;
if (cpu_class_is_omap1()) {
/* OMAP1's can use only external source clock */
if (unlikely(clk_id == OMAP_MCBSP_SYSCLK_CLKS_FCLK))
return -EINVAL;
else
return 0;
}
if (cpu_is_omap2420() && mcbsp_data->bus_id > 1)
return -EINVAL;
if (cpu_is_omap343x())
reg_devconf1 = OMAP343X_CONTROL_DEVCONF1;
switch (mcbsp_data->bus_id) {
case 0:
reg = OMAP2_CONTROL_DEVCONF0;
sel_bit = 2;
break;
case 1:
reg = OMAP2_CONTROL_DEVCONF0;
sel_bit = 6;
break;
case 2:
reg = reg_devconf1;
sel_bit = 0;
break;
case 3:
reg = reg_devconf1;
sel_bit = 2;
break;
case 4:
reg = reg_devconf1;
sel_bit = 4;
break;
default:
return -EINVAL;
}
if (clk_id == OMAP_MCBSP_SYSCLK_CLKS_FCLK)
omap_ctrl_writel(omap_ctrl_readl(reg) & ~(1 << sel_bit), reg);
else
omap_ctrl_writel(omap_ctrl_readl(reg) | (1 << sel_bit), reg);
return 0;
}
static int omap_mcbsp_dai_set_dai_sysclk(struct snd_soc_dai *cpu_dai,
int clk_id, unsigned int freq,
int dir)
{
struct omap_mcbsp_data *mcbsp_data = to_mcbsp(cpu_dai->private_data);
struct omap_mcbsp_reg_cfg *regs = &mcbsp_data->regs;
int err = 0;
switch (clk_id) {
case OMAP_MCBSP_SYSCLK_CLK:
regs->srgr2 |= CLKSM;
break;
case OMAP_MCBSP_SYSCLK_CLKS_FCLK:
case OMAP_MCBSP_SYSCLK_CLKS_EXT:
err = omap_mcbsp_dai_set_clks_src(mcbsp_data, clk_id);
break;
case OMAP_MCBSP_SYSCLK_CLKX_EXT:
regs->srgr2 |= CLKSM;
case OMAP_MCBSP_SYSCLK_CLKR_EXT:
regs->pcr0 |= SCLKME;
break;
default:
err = -ENODEV;
}
return err;
}
static struct snd_soc_dai_ops omap_mcbsp_dai_ops = {
.startup = omap_mcbsp_dai_startup,
.shutdown = omap_mcbsp_dai_shutdown,
.trigger = omap_mcbsp_dai_trigger,
.hw_params = omap_mcbsp_dai_hw_params,
.set_fmt = omap_mcbsp_dai_set_dai_fmt,
.set_clkdiv = omap_mcbsp_dai_set_clkdiv,
.set_sysclk = omap_mcbsp_dai_set_dai_sysclk,
};
#define OMAP_MCBSP_DAI_BUILDER(link_id) \
{ \
.name = "omap-mcbsp-dai-"#link_id, \
.id = (link_id), \
.playback = { \
.channels_min = 1, \
.channels_max = 4, \
.rates = OMAP_MCBSP_RATES, \
.formats = SNDRV_PCM_FMTBIT_S16_LE, \
}, \
.capture = { \
.channels_min = 1, \
.channels_max = 4, \
.rates = OMAP_MCBSP_RATES, \
.formats = SNDRV_PCM_FMTBIT_S16_LE, \
}, \
.ops = &omap_mcbsp_dai_ops, \
.private_data = &mcbsp_data[(link_id)].bus_id, \
}
struct snd_soc_dai omap_mcbsp_dai[] = {
OMAP_MCBSP_DAI_BUILDER(0),
OMAP_MCBSP_DAI_BUILDER(1),
#if NUM_LINKS >= 3
OMAP_MCBSP_DAI_BUILDER(2),
#endif
#if NUM_LINKS == 5
OMAP_MCBSP_DAI_BUILDER(3),
OMAP_MCBSP_DAI_BUILDER(4),
#endif
};
EXPORT_SYMBOL_GPL(omap_mcbsp_dai);
static int __init snd_omap_mcbsp_init(void)
{
return snd_soc_register_dais(omap_mcbsp_dai,
ARRAY_SIZE(omap_mcbsp_dai));
}
module_init(snd_omap_mcbsp_init);
static void __exit snd_omap_mcbsp_exit(void)
{
snd_soc_unregister_dais(omap_mcbsp_dai, ARRAY_SIZE(omap_mcbsp_dai));
}
module_exit(snd_omap_mcbsp_exit);
MODULE_AUTHOR("Jarkko Nikula <jhnikula@gmail.com>");
MODULE_DESCRIPTION("OMAP I2S SoC Interface");
MODULE_LICENSE("GPL");