2008-12-10 18:37:17 -07:00
|
|
|
/*
|
|
|
|
* linux/arch/arm/mach-omap2/mmc-twl4030.c
|
|
|
|
*
|
|
|
|
* Copyright (C) 2007-2008 Texas Instruments
|
|
|
|
* Copyright (C) 2008 Nokia Corporation
|
|
|
|
* Author: Texas Instruments
|
|
|
|
*
|
|
|
|
* This program is free software; you can redistribute it and/or modify
|
|
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
|
|
* published by the Free Software Foundation.
|
|
|
|
*/
|
|
|
|
#include <linux/err.h>
|
|
|
|
#include <linux/io.h>
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/platform_device.h>
|
|
|
|
#include <linux/interrupt.h>
|
|
|
|
#include <linux/delay.h>
|
|
|
|
#include <linux/gpio.h>
|
2009-05-28 15:04:03 -06:00
|
|
|
#include <linux/mmc/host.h>
|
|
|
|
#include <linux/regulator/consumer.h>
|
2008-12-10 18:37:17 -07:00
|
|
|
|
|
|
|
#include <mach/hardware.h>
|
|
|
|
#include <mach/control.h>
|
|
|
|
#include <mach/mmc.h>
|
|
|
|
#include <mach/board.h>
|
|
|
|
|
|
|
|
#include "mmc-twl4030.h"
|
|
|
|
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
#if defined(CONFIG_REGULATOR) && \
|
|
|
|
(defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE))
|
2008-12-10 18:37:17 -07:00
|
|
|
|
|
|
|
static u16 control_pbias_offset;
|
|
|
|
static u16 control_devconf1_offset;
|
|
|
|
|
|
|
|
#define HSMMC_NAME_LEN 9
|
|
|
|
|
|
|
|
static struct twl_mmc_controller {
|
|
|
|
struct omap_mmc_platform_data *mmc;
|
2009-05-28 15:04:03 -06:00
|
|
|
/* Vcc == configured supply
|
|
|
|
* Vcc_alt == optional
|
|
|
|
* - MMC1, supply for DAT4..DAT7
|
|
|
|
* - MMC2/MMC2, external level shifter voltage supply, for
|
|
|
|
* chip (SDIO, eMMC, etc) or transceiver (MMC2 only)
|
|
|
|
*/
|
|
|
|
struct regulator *vcc;
|
|
|
|
struct regulator *vcc_aux;
|
|
|
|
char name[HSMMC_NAME_LEN + 1];
|
|
|
|
} hsmmc[OMAP34XX_NR_MMC];
|
2008-12-10 18:37:17 -07:00
|
|
|
|
|
|
|
static int twl_mmc_card_detect(int irq)
|
|
|
|
{
|
|
|
|
unsigned i;
|
|
|
|
|
|
|
|
for (i = 0; i < ARRAY_SIZE(hsmmc); i++) {
|
|
|
|
struct omap_mmc_platform_data *mmc;
|
|
|
|
|
|
|
|
mmc = hsmmc[i].mmc;
|
|
|
|
if (!mmc)
|
|
|
|
continue;
|
|
|
|
if (irq != mmc->slots[0].card_detect_irq)
|
|
|
|
continue;
|
|
|
|
|
|
|
|
/* NOTE: assumes card detect signal is active-low */
|
|
|
|
return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
|
|
|
|
}
|
|
|
|
return -ENOSYS;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int twl_mmc_get_ro(struct device *dev, int slot)
|
|
|
|
{
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
|
|
|
/* NOTE: assumes write protect signal is active-high */
|
|
|
|
return gpio_get_value_cansleep(mmc->slots[0].gpio_wp);
|
|
|
|
}
|
|
|
|
|
2009-03-23 19:23:48 -06:00
|
|
|
static int twl_mmc_get_cover_state(struct device *dev, int slot)
|
|
|
|
{
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
|
|
|
/* NOTE: assumes card detect signal is active-low */
|
|
|
|
return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
|
|
|
|
}
|
|
|
|
|
2008-12-10 18:37:17 -07:00
|
|
|
/*
|
|
|
|
* MMC Slot Initialization.
|
|
|
|
*/
|
|
|
|
static int twl_mmc_late_init(struct device *dev)
|
|
|
|
{
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
int ret = 0;
|
|
|
|
int i;
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
/* MMC/SD/SDIO doesn't require a card detect switch */
|
|
|
|
if (gpio_is_valid(mmc->slots[0].switch_pin)) {
|
|
|
|
ret = gpio_request(mmc->slots[0].switch_pin, "mmc_cd");
|
|
|
|
if (ret)
|
|
|
|
goto done;
|
|
|
|
ret = gpio_direction_input(mmc->slots[0].switch_pin);
|
|
|
|
if (ret)
|
|
|
|
goto err;
|
|
|
|
}
|
2008-12-10 18:37:17 -07:00
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
/* require at least main regulator */
|
2008-12-10 18:37:17 -07:00
|
|
|
for (i = 0; i < ARRAY_SIZE(hsmmc); i++) {
|
|
|
|
if (hsmmc[i].name == mmc->slots[0].name) {
|
2009-05-28 15:04:03 -06:00
|
|
|
struct regulator *reg;
|
|
|
|
|
2008-12-10 18:37:17 -07:00
|
|
|
hsmmc[i].mmc = mmc;
|
2009-05-28 15:04:03 -06:00
|
|
|
|
|
|
|
reg = regulator_get(dev, "vmmc");
|
|
|
|
if (IS_ERR(reg)) {
|
|
|
|
dev_dbg(dev, "vmmc regulator missing\n");
|
|
|
|
/* HACK: until fixed.c regulator is usable,
|
|
|
|
* we don't require a main regulator
|
|
|
|
* for MMC2 or MMC3
|
|
|
|
*/
|
|
|
|
if (i != 0)
|
|
|
|
break;
|
|
|
|
ret = PTR_ERR(reg);
|
|
|
|
goto err;
|
|
|
|
}
|
|
|
|
hsmmc[i].vcc = reg;
|
|
|
|
mmc->slots[0].ocr_mask = mmc_regulator_get_ocrmask(reg);
|
|
|
|
|
|
|
|
/* allow an aux regulator */
|
|
|
|
reg = regulator_get(dev, "vmmc_aux");
|
|
|
|
hsmmc[i].vcc_aux = IS_ERR(reg) ? NULL : reg;
|
|
|
|
|
|
|
|
/* UGLY HACK: workaround regulator framework bugs.
|
|
|
|
* When the bootloader leaves a supply active, it's
|
|
|
|
* initialized with zero usecount ... and we can't
|
|
|
|
* disable it without first enabling it. Until the
|
|
|
|
* framework is fixed, we need a workaround like this
|
|
|
|
* (which is safe for MMC, but not in general).
|
|
|
|
*/
|
|
|
|
if (regulator_is_enabled(hsmmc[i].vcc) > 0) {
|
|
|
|
regulator_enable(hsmmc[i].vcc);
|
|
|
|
regulator_disable(hsmmc[i].vcc);
|
|
|
|
}
|
|
|
|
if (hsmmc[i].vcc_aux) {
|
|
|
|
if (regulator_is_enabled(reg) > 0) {
|
|
|
|
regulator_enable(reg);
|
|
|
|
regulator_disable(reg);
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
2008-12-10 18:37:17 -07:00
|
|
|
break;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
|
|
|
|
err:
|
|
|
|
gpio_free(mmc->slots[0].switch_pin);
|
|
|
|
done:
|
|
|
|
mmc->slots[0].card_detect_irq = 0;
|
|
|
|
mmc->slots[0].card_detect = NULL;
|
|
|
|
|
|
|
|
dev_err(dev, "err %d configuring card detect\n", ret);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static void twl_mmc_cleanup(struct device *dev)
|
|
|
|
{
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
|
|
|
gpio_free(mmc->slots[0].switch_pin);
|
|
|
|
}
|
|
|
|
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
|
|
|
|
static int twl_mmc_suspend(struct device *dev, int slot)
|
|
|
|
{
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
|
|
|
disable_irq(mmc->slots[0].card_detect_irq);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int twl_mmc_resume(struct device *dev, int slot)
|
|
|
|
{
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
|
|
|
enable_irq(mmc->slots[0].card_detect_irq);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
#else
|
|
|
|
#define twl_mmc_suspend NULL
|
|
|
|
#define twl_mmc_resume NULL
|
|
|
|
#endif
|
|
|
|
|
|
|
|
static int twl_mmc1_set_power(struct device *dev, int slot, int power_on,
|
|
|
|
int vdd)
|
|
|
|
{
|
|
|
|
u32 reg;
|
|
|
|
int ret = 0;
|
|
|
|
struct twl_mmc_controller *c = &hsmmc[0];
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
2009-03-23 19:23:47 -06:00
|
|
|
/*
|
|
|
|
* Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
|
2009-05-28 15:04:03 -06:00
|
|
|
* card with Vcc regulator (from twl4030 or whatever). OMAP has both
|
2009-03-23 19:23:47 -06:00
|
|
|
* 1.8V and 3.0V modes, controlled by the PBIAS register.
|
|
|
|
*
|
|
|
|
* In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
|
|
|
|
* is most naturally TWL VSIM; those pins also use PBIAS.
|
2009-05-28 15:04:03 -06:00
|
|
|
*
|
|
|
|
* FIXME handle VMMC1A as needed ...
|
2009-03-23 19:23:47 -06:00
|
|
|
*/
|
2008-12-10 18:37:17 -07:00
|
|
|
if (power_on) {
|
|
|
|
if (cpu_is_omap2430()) {
|
|
|
|
reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1);
|
|
|
|
if ((1 << vdd) >= MMC_VDD_30_31)
|
|
|
|
reg |= OMAP243X_MMC1_ACTIVE_OVERWRITE;
|
|
|
|
else
|
|
|
|
reg &= ~OMAP243X_MMC1_ACTIVE_OVERWRITE;
|
|
|
|
omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1);
|
|
|
|
}
|
|
|
|
|
|
|
|
if (mmc->slots[0].internal_clock) {
|
|
|
|
reg = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
|
|
|
|
reg |= OMAP2_MMCSDIO1ADPCLKISEL;
|
|
|
|
omap_ctrl_writel(reg, OMAP2_CONTROL_DEVCONF0);
|
|
|
|
}
|
|
|
|
|
|
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
|
|
reg |= OMAP2_PBIASSPEEDCTRL0;
|
|
|
|
reg &= ~OMAP2_PBIASLITEPWRDNZ0;
|
|
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
ret = mmc_regulator_set_ocr(c->vcc, vdd);
|
2008-12-10 18:37:17 -07:00
|
|
|
|
|
|
|
/* 100ms delay required for PBIAS configuration */
|
|
|
|
msleep(100);
|
|
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
|
|
reg |= (OMAP2_PBIASLITEPWRDNZ0 | OMAP2_PBIASSPEEDCTRL0);
|
|
|
|
if ((1 << vdd) <= MMC_VDD_165_195)
|
|
|
|
reg &= ~OMAP2_PBIASLITEVMODE0;
|
|
|
|
else
|
|
|
|
reg |= OMAP2_PBIASLITEVMODE0;
|
|
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
|
|
} else {
|
|
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
|
|
reg &= ~OMAP2_PBIASLITEPWRDNZ0;
|
|
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
ret = mmc_regulator_set_ocr(c->vcc, 0);
|
2008-12-10 18:37:17 -07:00
|
|
|
|
|
|
|
/* 100ms delay required for PBIAS configuration */
|
|
|
|
msleep(100);
|
|
|
|
reg = omap_ctrl_readl(control_pbias_offset);
|
|
|
|
reg |= (OMAP2_PBIASSPEEDCTRL0 | OMAP2_PBIASLITEPWRDNZ0 |
|
|
|
|
OMAP2_PBIASLITEVMODE0);
|
|
|
|
omap_ctrl_writel(reg, control_pbias_offset);
|
|
|
|
}
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
static int twl_mmc23_set_power(struct device *dev, int slot, int power_on, int vdd)
|
2008-12-10 18:37:17 -07:00
|
|
|
{
|
2009-05-28 15:04:03 -06:00
|
|
|
int ret = 0;
|
2008-12-10 18:37:17 -07:00
|
|
|
struct twl_mmc_controller *c = &hsmmc[1];
|
|
|
|
struct omap_mmc_platform_data *mmc = dev->platform_data;
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
/* If we don't see a Vcc regulator, assume it's a fixed
|
|
|
|
* voltage always-on regulator.
|
|
|
|
*/
|
|
|
|
if (!c->vcc)
|
|
|
|
return 0;
|
|
|
|
|
2009-03-23 19:23:47 -06:00
|
|
|
/*
|
2009-05-28 15:04:03 -06:00
|
|
|
* Assume Vcc regulator is used only to power the card ... OMAP
|
2009-03-23 19:23:47 -06:00
|
|
|
* VDDS is used to power the pins, optionally with a transceiver to
|
|
|
|
* support cards using voltages other than VDDS (1.8V nominal). When a
|
|
|
|
* transceiver is used, DAT3..7 are muxed as transceiver control pins.
|
2009-05-28 15:04:03 -06:00
|
|
|
*
|
|
|
|
* In some cases this regulator won't support enable/disable;
|
|
|
|
* e.g. it's a fixed rail for a WLAN chip.
|
|
|
|
*
|
|
|
|
* In other cases vcc_aux switches interface power. Example, for
|
|
|
|
* eMMC cards it represents VccQ. Sometimes transceivers or SDIO
|
|
|
|
* chips/cards need an interface voltage rail too.
|
2009-03-23 19:23:47 -06:00
|
|
|
*/
|
2008-12-10 18:37:17 -07:00
|
|
|
if (power_on) {
|
2009-05-28 15:04:03 -06:00
|
|
|
/* only MMC2 supports a CLKIN */
|
2008-12-10 18:37:17 -07:00
|
|
|
if (mmc->slots[0].internal_clock) {
|
|
|
|
u32 reg;
|
|
|
|
|
|
|
|
reg = omap_ctrl_readl(control_devconf1_offset);
|
|
|
|
reg |= OMAP2_MMCSDIO2ADPCLKISEL;
|
|
|
|
omap_ctrl_writel(reg, control_devconf1_offset);
|
|
|
|
}
|
2009-05-28 15:04:03 -06:00
|
|
|
ret = mmc_regulator_set_ocr(c->vcc, vdd);
|
|
|
|
/* enable interface voltage rail, if needed */
|
|
|
|
if (ret == 0 && c->vcc_aux) {
|
|
|
|
ret = regulator_enable(c->vcc_aux);
|
|
|
|
if (ret < 0)
|
|
|
|
ret = mmc_regulator_set_ocr(c->vcc, 0);
|
|
|
|
}
|
2008-12-10 18:37:17 -07:00
|
|
|
} else {
|
2009-05-28 15:04:03 -06:00
|
|
|
if (c->vcc_aux && (ret = regulator_is_enabled(c->vcc_aux)) > 0)
|
|
|
|
ret = regulator_disable(c->vcc_aux);
|
|
|
|
if (ret == 0)
|
|
|
|
ret = mmc_regulator_set_ocr(c->vcc, 0);
|
2008-12-10 18:37:17 -07:00
|
|
|
}
|
|
|
|
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static struct omap_mmc_platform_data *hsmmc_data[OMAP34XX_NR_MMC] __initdata;
|
|
|
|
|
|
|
|
void __init twl4030_mmc_init(struct twl4030_hsmmc_info *controllers)
|
|
|
|
{
|
|
|
|
struct twl4030_hsmmc_info *c;
|
|
|
|
int nr_hsmmc = ARRAY_SIZE(hsmmc_data);
|
|
|
|
|
|
|
|
if (cpu_is_omap2430()) {
|
|
|
|
control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE;
|
|
|
|
control_devconf1_offset = OMAP243X_CONTROL_DEVCONF1;
|
|
|
|
nr_hsmmc = 2;
|
|
|
|
} else {
|
|
|
|
control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
|
|
|
|
control_devconf1_offset = OMAP343X_CONTROL_DEVCONF1;
|
|
|
|
}
|
|
|
|
|
|
|
|
for (c = controllers; c->mmc; c++) {
|
|
|
|
struct twl_mmc_controller *twl = hsmmc + c->mmc - 1;
|
|
|
|
struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
|
|
|
|
|
|
|
|
if (!c->mmc || c->mmc > nr_hsmmc) {
|
|
|
|
pr_debug("MMC%d: no such controller\n", c->mmc);
|
|
|
|
continue;
|
|
|
|
}
|
|
|
|
if (mmc) {
|
|
|
|
pr_debug("MMC%d: already configured\n", c->mmc);
|
|
|
|
continue;
|
|
|
|
}
|
|
|
|
|
|
|
|
mmc = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
|
|
|
|
if (!mmc) {
|
|
|
|
pr_err("Cannot allocate memory for mmc device!\n");
|
|
|
|
return;
|
|
|
|
}
|
|
|
|
|
2009-03-23 19:23:48 -06:00
|
|
|
if (c->name)
|
|
|
|
strncpy(twl->name, c->name, HSMMC_NAME_LEN);
|
|
|
|
else
|
|
|
|
snprintf(twl->name, ARRAY_SIZE(twl->name),
|
|
|
|
"mmc%islot%i", c->mmc, 1);
|
2008-12-10 18:37:17 -07:00
|
|
|
mmc->slots[0].name = twl->name;
|
|
|
|
mmc->nr_slots = 1;
|
|
|
|
mmc->slots[0].wires = c->wires;
|
|
|
|
mmc->slots[0].internal_clock = !c->ext_clock;
|
|
|
|
mmc->dma_mask = 0xffffffff;
|
2009-05-28 15:04:03 -06:00
|
|
|
mmc->init = twl_mmc_late_init;
|
2008-12-10 18:37:17 -07:00
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
/* note: twl4030 card detect GPIOs can disable VMMCx ... */
|
2008-12-10 18:37:17 -07:00
|
|
|
if (gpio_is_valid(c->gpio_cd)) {
|
|
|
|
mmc->cleanup = twl_mmc_cleanup;
|
|
|
|
mmc->suspend = twl_mmc_suspend;
|
|
|
|
mmc->resume = twl_mmc_resume;
|
|
|
|
|
|
|
|
mmc->slots[0].switch_pin = c->gpio_cd;
|
|
|
|
mmc->slots[0].card_detect_irq = gpio_to_irq(c->gpio_cd);
|
2009-03-23 19:23:48 -06:00
|
|
|
if (c->cover_only)
|
|
|
|
mmc->slots[0].get_cover_state = twl_mmc_get_cover_state;
|
|
|
|
else
|
|
|
|
mmc->slots[0].card_detect = twl_mmc_card_detect;
|
2008-12-10 18:37:17 -07:00
|
|
|
} else
|
|
|
|
mmc->slots[0].switch_pin = -EINVAL;
|
|
|
|
|
|
|
|
/* write protect normally uses an OMAP gpio */
|
|
|
|
if (gpio_is_valid(c->gpio_wp)) {
|
|
|
|
gpio_request(c->gpio_wp, "mmc_wp");
|
|
|
|
gpio_direction_input(c->gpio_wp);
|
|
|
|
|
|
|
|
mmc->slots[0].gpio_wp = c->gpio_wp;
|
|
|
|
mmc->slots[0].get_ro = twl_mmc_get_ro;
|
|
|
|
} else
|
|
|
|
mmc->slots[0].gpio_wp = -EINVAL;
|
|
|
|
|
2009-05-28 15:04:03 -06:00
|
|
|
/* NOTE: MMC slots should have a Vcc regulator set up.
|
|
|
|
* This may be from a TWL4030-family chip, another
|
|
|
|
* controllable regulator, or a fixed supply.
|
|
|
|
*
|
|
|
|
* temporary HACK: ocr_mask instead of fixed supply
|
2008-12-10 18:37:17 -07:00
|
|
|
*/
|
2009-05-28 15:04:03 -06:00
|
|
|
mmc->slots[0].ocr_mask = c->ocr_mask;
|
2008-12-10 18:37:17 -07:00
|
|
|
|
|
|
|
switch (c->mmc) {
|
|
|
|
case 1:
|
2009-05-28 15:04:03 -06:00
|
|
|
/* on-chip level shifting via PBIAS0/PBIAS1 */
|
2008-12-10 18:37:17 -07:00
|
|
|
mmc->slots[0].set_power = twl_mmc1_set_power;
|
|
|
|
break;
|
|
|
|
case 2:
|
2009-05-28 15:04:03 -06:00
|
|
|
if (c->ext_clock)
|
|
|
|
c->transceiver = 1;
|
|
|
|
if (c->transceiver && c->wires > 4)
|
|
|
|
c->wires = 4;
|
|
|
|
/* FALLTHROUGH */
|
2009-03-23 19:23:47 -06:00
|
|
|
case 3:
|
2009-05-28 15:04:03 -06:00
|
|
|
/* off-chip level shifting, or none */
|
|
|
|
mmc->slots[0].set_power = twl_mmc23_set_power;
|
2009-03-23 19:23:47 -06:00
|
|
|
break;
|
2008-12-10 18:37:17 -07:00
|
|
|
default:
|
|
|
|
pr_err("MMC%d configuration not supported!\n", c->mmc);
|
2009-03-23 19:23:47 -06:00
|
|
|
kfree(mmc);
|
2008-12-10 18:37:17 -07:00
|
|
|
continue;
|
|
|
|
}
|
|
|
|
hsmmc_data[c->mmc - 1] = mmc;
|
|
|
|
}
|
|
|
|
|
|
|
|
omap2_init_mmc(hsmmc_data, OMAP34XX_NR_MMC);
|
2009-03-23 19:23:47 -06:00
|
|
|
|
|
|
|
/* pass the device nodes back to board setup code */
|
|
|
|
for (c = controllers; c->mmc; c++) {
|
|
|
|
struct omap_mmc_platform_data *mmc = hsmmc_data[c->mmc - 1];
|
|
|
|
|
|
|
|
if (!c->mmc || c->mmc > nr_hsmmc)
|
|
|
|
continue;
|
|
|
|
c->dev = mmc->dev;
|
|
|
|
}
|
2008-12-10 18:37:17 -07:00
|
|
|
}
|
|
|
|
|
|
|
|
#endif
|