2018-01-11 03:08:54 -07:00
|
|
|
// SPDX-License-Identifier: GPL-2.0+
|
2016-01-27 02:04:23 -07:00
|
|
|
/*
|
|
|
|
* FB driver for the SSD1305 OLED Controller
|
|
|
|
*
|
|
|
|
* based on SSD1306 driver by Noralf Tronnes
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <linux/module.h>
|
|
|
|
#include <linux/kernel.h>
|
|
|
|
#include <linux/init.h>
|
2019-01-16 10:30:50 -07:00
|
|
|
#include <linux/gpio/consumer.h>
|
2016-01-27 02:04:23 -07:00
|
|
|
#include <linux/delay.h>
|
|
|
|
|
|
|
|
#include "fbtft.h"
|
|
|
|
|
|
|
|
#define DRVNAME "fb_ssd1305"
|
|
|
|
|
|
|
|
#define WIDTH 128
|
|
|
|
#define HEIGHT 64
|
|
|
|
|
|
|
|
/*
|
|
|
|
* write_reg() caveat:
|
|
|
|
*
|
|
|
|
* This doesn't work because D/C has to be LOW for both values:
|
|
|
|
* write_reg(par, val1, val2);
|
|
|
|
*
|
|
|
|
* Do it like this:
|
|
|
|
* write_reg(par, val1);
|
|
|
|
* write_reg(par, val2);
|
|
|
|
*/
|
|
|
|
|
|
|
|
/* Init sequence taken from the Adafruit SSD1306 Arduino library */
|
|
|
|
static int init_display(struct fbtft_par *par)
|
|
|
|
{
|
|
|
|
par->fbtftops.reset(par);
|
|
|
|
|
|
|
|
if (par->gamma.curves[0] == 0) {
|
|
|
|
mutex_lock(&par->gamma.lock);
|
|
|
|
if (par->info->var.yres == 64)
|
|
|
|
par->gamma.curves[0] = 0xCF;
|
|
|
|
else
|
|
|
|
par->gamma.curves[0] = 0x8F;
|
|
|
|
mutex_unlock(&par->gamma.lock);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Set Display OFF */
|
|
|
|
write_reg(par, 0xAE);
|
|
|
|
|
|
|
|
/* Set Display Clock Divide Ratio/ Oscillator Frequency */
|
|
|
|
write_reg(par, 0xD5);
|
|
|
|
write_reg(par, 0x80);
|
|
|
|
|
|
|
|
/* Set Multiplex Ratio */
|
|
|
|
write_reg(par, 0xA8);
|
|
|
|
if (par->info->var.yres == 64)
|
|
|
|
write_reg(par, 0x3F);
|
|
|
|
else
|
|
|
|
write_reg(par, 0x1F);
|
|
|
|
|
|
|
|
/* Set Display Offset */
|
|
|
|
write_reg(par, 0xD3);
|
|
|
|
write_reg(par, 0x0);
|
|
|
|
|
|
|
|
/* Set Display Start Line */
|
|
|
|
write_reg(par, 0x40 | 0x0);
|
|
|
|
|
|
|
|
/* Charge Pump Setting */
|
|
|
|
write_reg(par, 0x8D);
|
|
|
|
/* A[2] = 1b, Enable charge pump during display on */
|
|
|
|
write_reg(par, 0x14);
|
|
|
|
|
|
|
|
/* Set Memory Addressing Mode */
|
|
|
|
write_reg(par, 0x20);
|
|
|
|
/* Vertical addressing mode */
|
|
|
|
write_reg(par, 0x01);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Set Segment Re-map
|
|
|
|
* column address 127 is mapped to SEG0
|
|
|
|
*/
|
|
|
|
write_reg(par, 0xA0 | ((par->info->var.rotate == 180) ? 0x0 : 0x1));
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Set COM Output Scan Direction
|
|
|
|
* remapped mode. Scan from COM[N-1] to COM0
|
|
|
|
*/
|
|
|
|
write_reg(par, ((par->info->var.rotate == 180) ? 0xC8 : 0xC0));
|
|
|
|
|
|
|
|
/* Set COM Pins Hardware Configuration */
|
|
|
|
write_reg(par, 0xDA);
|
|
|
|
if (par->info->var.yres == 64) {
|
|
|
|
/* A[4]=1b, Alternative COM pin configuration */
|
|
|
|
write_reg(par, 0x12);
|
|
|
|
} else {
|
|
|
|
/* A[4]=0b, Sequential COM pin configuration */
|
|
|
|
write_reg(par, 0x02);
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Set Pre-charge Period */
|
|
|
|
write_reg(par, 0xD9);
|
|
|
|
write_reg(par, 0xF1);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Entire Display ON
|
|
|
|
* Resume to RAM content display. Output follows RAM content
|
|
|
|
*/
|
|
|
|
write_reg(par, 0xA4);
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Set Normal Display
|
|
|
|
* 0 in RAM: OFF in display panel
|
|
|
|
* 1 in RAM: ON in display panel
|
|
|
|
*/
|
|
|
|
write_reg(par, 0xA6);
|
|
|
|
|
|
|
|
/* Set Display ON */
|
|
|
|
write_reg(par, 0xAF);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye)
|
|
|
|
{
|
|
|
|
/* Set Lower Column Start Address for Page Addressing Mode */
|
|
|
|
write_reg(par, 0x00 | ((par->info->var.rotate == 180) ? 0x0 : 0x4));
|
|
|
|
/* Set Higher Column Start Address for Page Addressing Mode */
|
|
|
|
write_reg(par, 0x10 | 0x0);
|
|
|
|
/* Set Display Start Line */
|
|
|
|
write_reg(par, 0x40 | 0x0);
|
|
|
|
}
|
|
|
|
|
|
|
|
static int blank(struct fbtft_par *par, bool on)
|
|
|
|
{
|
|
|
|
if (on)
|
|
|
|
write_reg(par, 0xAE);
|
|
|
|
else
|
|
|
|
write_reg(par, 0xAF);
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Gamma is used to control Contrast */
|
2017-02-02 07:43:42 -07:00
|
|
|
static int set_gamma(struct fbtft_par *par, u32 *curves)
|
2016-01-27 02:04:23 -07:00
|
|
|
{
|
|
|
|
curves[0] &= 0xFF;
|
|
|
|
/* Set Contrast Control for BANK0 */
|
|
|
|
write_reg(par, 0x81);
|
|
|
|
write_reg(par, curves[0]);
|
|
|
|
|
|
|
|
return 0;
|
|
|
|
}
|
|
|
|
|
|
|
|
static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
|
|
|
|
{
|
|
|
|
u16 *vmem16 = (u16 *)par->info->screen_buffer;
|
|
|
|
u8 *buf = par->txbuf.buf;
|
|
|
|
int x, y, i;
|
|
|
|
int ret;
|
|
|
|
|
|
|
|
for (x = 0; x < par->info->var.xres; x++) {
|
|
|
|
for (y = 0; y < par->info->var.yres / 8; y++) {
|
|
|
|
*buf = 0x00;
|
|
|
|
for (i = 0; i < 8; i++)
|
|
|
|
*buf |= (vmem16[(y * 8 + i) *
|
|
|
|
par->info->var.xres + x] ?
|
|
|
|
1 : 0) << i;
|
|
|
|
buf++;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Write data */
|
2019-01-16 10:30:50 -07:00
|
|
|
gpiod_set_value(par->gpio.dc, 1);
|
2016-01-27 02:04:23 -07:00
|
|
|
ret = par->fbtftops.write(par, par->txbuf.buf,
|
|
|
|
par->info->var.xres * par->info->var.yres /
|
|
|
|
8);
|
|
|
|
if (ret < 0)
|
|
|
|
dev_err(par->info->device, "write failed and returned: %d\n",
|
|
|
|
ret);
|
|
|
|
return ret;
|
|
|
|
}
|
|
|
|
|
|
|
|
static struct fbtft_display display = {
|
|
|
|
.regwidth = 8,
|
|
|
|
.width = WIDTH,
|
|
|
|
.height = HEIGHT,
|
|
|
|
.txbuflen = WIDTH * HEIGHT / 8,
|
|
|
|
.gamma_num = 1,
|
|
|
|
.gamma_len = 1,
|
|
|
|
.gamma = "00",
|
|
|
|
.fbtftops = {
|
|
|
|
.write_vmem = write_vmem,
|
|
|
|
.init_display = init_display,
|
|
|
|
.set_addr_win = set_addr_win,
|
|
|
|
.blank = blank,
|
|
|
|
.set_gamma = set_gamma,
|
|
|
|
},
|
|
|
|
};
|
|
|
|
|
|
|
|
FBTFT_REGISTER_DRIVER(DRVNAME, "solomon,ssd1305", &display);
|
|
|
|
|
|
|
|
MODULE_ALIAS("spi:" DRVNAME);
|
|
|
|
MODULE_ALIAS("platform:" DRVNAME);
|
|
|
|
MODULE_ALIAS("spi:ssd1305");
|
|
|
|
MODULE_ALIAS("platform:ssd1305");
|
|
|
|
|
|
|
|
MODULE_DESCRIPTION("SSD1305 OLED Driver");
|
|
|
|
MODULE_AUTHOR("Alexey Mednyy");
|
|
|
|
MODULE_LICENSE("GPL");
|