redonkable
/
alistair23-linux
1
0
Fork 0
Code Releases Activity

omap2/3/4: serial: errata i202: fix for MDR1 access 

Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.

Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register

Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation

Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c

Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hifive-unleashed-5.1
Deepak K 2010-08-02 13:18:12 +03:00 committed by Tony Lindgren
parent 5a927b36f5
commit 0003450964
1 changed files with 49 additions and 3 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

52
arch/arm/mach-omap2/serial.c
View File

@ -38,6 +38,7 @@
#define UART_OMAP_WER 0x17 /* Wake-up enable register */
#define UART_ERRATA_FIFO_FULL_ABORT (0x1 << 0)
#define UART_ERRATA_i202_MDR1_ACCESS (0x1 << 1)
/*
* NOTE: By default the serial timeout is disabled as it causes lost characters
@ -184,6 +185,42 @@ static inline void __init omap_uart_reset(struct omap_uart_state *uart)
#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3)
/*
* Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6)
* The access to uart register after MDR1 Access
* causes UART to corrupt data.
*
* Need a delay =
* 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS)
* give 10 times as much
*/
static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val,
u8 fcr_val)
{
struct plat_serial8250_port *p = uart->p;
u8 timeout = 255;
serial_write_reg(p, UART_OMAP_MDR1, mdr1_val);
udelay(2);
serial_write_reg(p, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT |
UART_FCR_CLEAR_RCVR);
/*
* Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and
* TX_FIFO_E bit is 1.
*/
while (UART_LSR_THRE != (serial_read_reg(p, UART_LSR) &
(UART_LSR_THRE | UART_LSR_DR))) {
timeout--;
if (!timeout) {
/* Should *never* happen. we warn and carry on */
dev_crit(&uart->pdev.dev, "Errata i202: timedout %x\n",
serial_read_reg(p, UART_LSR));
break;
}
udelay(1);
}
}
static void omap_uart_save_context(struct omap_uart_state *uart)
{
u16 lcr = 0;
@ -221,7 +258,10 @@ static void omap_uart_restore_context(struct omap_uart_state *uart)
uart->context_valid = 0;
serial_write_reg(p, UART_OMAP_MDR1, 0x7);
if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
omap_uart_mdr1_errataset(uart, 0x07, 0xA0);
else
serial_write_reg(p, UART_OMAP_MDR1, 0x7);
serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
efr = serial_read_reg(p, UART_EFR);
serial_write_reg(p, UART_EFR, UART_EFR_ECB);
@ -234,14 +274,16 @@ static void omap_uart_restore_context(struct omap_uart_state *uart)
serial_write_reg(p, UART_IER, uart->ier);
serial_write_reg(p, UART_LCR, 0x80);
serial_write_reg(p, UART_MCR, uart->mcr);
serial_write_reg(p, UART_FCR, 0xA1);
serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */
serial_write_reg(p, UART_EFR, efr);
serial_write_reg(p, UART_LCR, UART_LCR_WLEN8);
serial_write_reg(p, UART_OMAP_SCR, uart->scr);
serial_write_reg(p, UART_OMAP_WER, uart->wer);
serial_write_reg(p, UART_OMAP_SYSC, uart->sysc);
serial_write_reg(p, UART_OMAP_MDR1, 0x00); /* UART 16x mode */
if (uart->errata & UART_ERRATA_i202_MDR1_ACCESS)
omap_uart_mdr1_errataset(uart, 0x00, 0xA1);
else
serial_write_reg(p, UART_OMAP_MDR1, 0x00); /* UART 16x mode */
}
#else
static inline void omap_uart_save_context(struct omap_uart_state *uart) {}
@ -769,6 +811,10 @@ void __init omap_serial_init_port(int port)
uart->p->serial_in = serial_in_override;
uart->p->serial_out = serial_out_override;
}
/* Enable the MDR1 errata for OMAP3 */
if (cpu_is_omap34xx())
uart->errata |= UART_ERRATA_i202_MDR1_ACCESS;
}
/**