Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:

 - a new driver for Rohm BU21029 touch controller

 - new bitmap APIs: bitmap_alloc, bitmap_zalloc and bitmap_free

 - updates to Atmel, eeti. pxrc and iforce drivers

 - assorted driver cleanups and fixes.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
  MAINTAINERS: Add PhoenixRC Flight Controller Adapter
  Input: do not use WARN() in input_alloc_absinfo()
  Input: mark expected switch fall-throughs
  Input: raydium_i2c_ts - use true and false for boolean values
  Input: evdev - switch to bitmap API
  Input: gpio-keys - switch to bitmap_zalloc()
  Input: elan_i2c_smbus - cast sizeof to int for comparison
  bitmap: Add bitmap_alloc(), bitmap_zalloc() and bitmap_free()
  md: Avoid namespace collision with bitmap API
  dm: Avoid namespace collision with bitmap API
  Input: pm8941-pwrkey - add resin entry
  Input: pm8941-pwrkey - abstract register offsets and event code
  Input: iforce - reorganize joystick configuration lists
  Input: atmel_mxt_ts - move completion to after config crc is updated
  Input: atmel_mxt_ts - don't report zero pressure from T9
  Input: atmel_mxt_ts - zero terminate config firmware file
  Input: atmel_mxt_ts - refactor config update code to add context struct
  Input: atmel_mxt_ts - config CRC may start at T71
  Input: atmel_mxt_ts - remove unnecessary debug on ENOMEM
  Input: atmel_mxt_ts - remove duplicate setup of ABS_MT_PRESSURE
  ...

Documentation/devicetree/bindings/input/keys.txt

@@ -0,0 +1,8 @@
+General Keys Properties:
+
+Optional properties for Keys:
+- power-off-time-sec: Duration in seconds which the key should be kept
+	pressed for device to power off automatically. Device with key pressed
+	shutdown feature can specify this property.
+- linux,keycodes: Specifies the numeric keycode values to be used for
+	reporting key presses.

Documentation/devicetree/bindings/input/qcom,pm8941-pwrkey.txt

@@ -7,6 +7,7 @@ PROPERTIES
 	Value type: <string>
 	Definition: must be one of:
 		    "qcom,pm8941-pwrkey"
+		    "qcom,pm8941-resin"
 
 - reg:
 	Usage: required
@@ -32,6 +33,14 @@ PROPERTIES
 	Definition: presence of this property indicates that the KPDPWR_N pin
 		    should be configured for pull up.
 
+- linux,code:
+	Usage: optional
+	Value type: <u32>
+	Definition: The input key-code associated with the power key.
+		    Use the linux event codes defined in
+		    include/dt-bindings/input/linux-event-codes.h
+		    When property is omitted KEY_POWER is assumed.
+
 EXAMPLE
 
 	pwrkey@800 {
@@ -40,4 +49,5 @@ EXAMPLE
 		interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 		debounce = <15625>;
 		bias-pull-up;
+		linux,code = <KEY_POWER>;
 	};

Documentation/devicetree/bindings/input/touchscreen/bu21029.txt

@@ -0,0 +1,35 @@
+* Rohm BU21029 Touch Screen Controller
+
+Required properties:
+ - compatible              : must be "rohm,bu21029"
+ - reg                     : i2c device address of the chip (0x40 or 0x41)
+ - interrupt-parent        : the phandle for the gpio controller
+ - interrupts              : (gpio) interrupt to which the chip is connected
+ - rohm,x-plate-ohms       : x-plate resistance in Ohm
+
+Optional properties:
+ - reset-gpios             : gpio pin to reset the chip (active low)
+ - touchscreen-size-x      : horizontal resolution of touchscreen (in pixels)
+ - touchscreen-size-y      : vertical resolution of touchscreen (in pixels)
+ - touchscreen-max-pressure: maximum pressure value
+ - vdd-supply              : power supply for the controller
+
+Example:
+
+	&i2c1 {
+		/* ... */
+
+		bu21029: bu21029@40 {
+			compatible = "rohm,bu21029";
+			reg = <0x40>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio6 16 GPIO_ACTIVE_LOW>;
+			rohm,x-plate-ohms = <600>;
+			touchscreen-size-x = <800>;
+			touchscreen-size-y = <480>;
+			touchscreen-max-pressure = <4095>;
+		};
+
+		/* ... */
+	};

Documentation/devicetree/bindings/input/touchscreen/eeti.txt

@@ -0,0 +1,30 @@
+Bindings for EETI touchscreen controller
+
+Required properties:
+- compatible:	should be "eeti,exc3000-i2c"
+- reg:		I2C address of the chip. Should be set to <0xa>
+- interrupts:	interrupt to which the chip is connected
+
+Optional properties:
+- attn-gpios:	A handle to a GPIO to check whether interrupt is still
+		latched. This is necessary for platforms that lack
+		support for level-triggered IRQs.
+
+The following optional properties described in touchscreen.txt are
+also supported:
+
+- touchscreen-inverted-x
+- touchscreen-inverted-y
+- touchscreen-swapped-x-y
+
+Example:
+
+i2c-master {
+	touchscreen@a {
+		compatible = "eeti,exc3000-i2c";
+		reg = <0xa>;
+		interrupt-parent = <&gpio>;
+		interrupts = <123 IRQ_TYPE_EDGE_RISING>;
+		attn-gpios = <&gpio 123 GPIO_ACTIVE_HIGH>;
+	};
+};

MAINTAINERS

@@ -11340,6 +11340,13 @@ S:	Maintained
 F:	include/linux/personality.h
 F:	include/uapi/linux/personality.h
 
+PHOENIX RC FLIGHT CONTROLLER ADAPTER
+M:	Marcus Folkesson <marcus.folkesson@gmail.com>
+L:	linux-input@vger.kernel.org
+S:	Maintained
+F:	Documentation/input/devices/pxrc.rst
+F:	drivers/input/joystick/pxrc.c
+
 PHONET PROTOCOL
 M:	Remi Denis-Courmont <courmisch@gmail.com>
 S:	Supported

drivers/input/evbug.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

drivers/input/evdev.c

@@ -481,7 +481,7 @@ static int evdev_release(struct inode *inode, struct file *file)
 	evdev_detach_client(evdev, client);
 
 	for (i = 0; i < EV_CNT; ++i)
-		kfree(client->evmasks[i]);
+		bitmap_free(client->evmasks[i]);
 
 	kvfree(client);
 
@@ -925,17 +925,15 @@ static int evdev_handle_get_val(struct evdev_client *client,
 {
 	int ret;
 	unsigned long *mem;
-	size_t len;
 
-	len = BITS_TO_LONGS(maxbit) * sizeof(unsigned long);
+	mem = bitmap_alloc(maxbit, GFP_KERNEL);
-	mem = kmalloc(len, GFP_KERNEL);
 	if (!mem)
 		return -ENOMEM;
 
 	spin_lock_irq(&dev->event_lock);
 	spin_lock(&client->buffer_lock);
 
-	memcpy(mem, bits, len);
+	bitmap_copy(mem, bits, maxbit);
 
 	spin_unlock(&dev->event_lock);
 
@@ -947,7 +945,7 @@ static int evdev_handle_get_val(struct evdev_client *client,
 	if (ret < 0)
 		evdev_queue_syn_dropped(client);
 
-	kfree(mem);
+	bitmap_free(mem);
 
 	return ret;
 }
@@ -1003,13 +1001,13 @@ static int evdev_set_mask(struct evdev_client *client,
 	if (!cnt)
 		return 0;
 
-	mask = kcalloc(sizeof(unsigned long), BITS_TO_LONGS(cnt), GFP_KERNEL);
+	mask = bitmap_zalloc(cnt, GFP_KERNEL);
 	if (!mask)
 		return -ENOMEM;
 
 	error = bits_from_user(mask, cnt - 1, codes_size, codes, compat);
 	if (error < 0) {
-		kfree(mask);
+		bitmap_free(mask);
 		return error;
 	}
 
@@ -1018,7 +1016,7 @@ static int evdev_set_mask(struct evdev_client *client,
 	client->evmasks[type] = mask;
 	spin_unlock_irqrestore(&client->buffer_lock, flags);
 
-	kfree(oldmask);
+	bitmap_free(oldmask);
 
 	return 0;
 }

drivers/input/gameport/emu10k1-gp.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <asm/io.h>

drivers/input/gameport/lightning.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <asm/io.h>

drivers/input/gameport/ns558.c

@@ -21,10 +21,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <asm/io.h>

drivers/input/input.c

@@ -480,11 +480,19 @@ EXPORT_SYMBOL(input_inject_event);
  */
 void input_alloc_absinfo(struct input_dev *dev)
 {
-	if (!dev->absinfo)
+	if (dev->absinfo)
-		dev->absinfo = kcalloc(ABS_CNT, sizeof(*dev->absinfo),
+		return;
-					GFP_KERNEL);
 
-	WARN(!dev->absinfo, "%s(): kcalloc() failed?\n", __func__);
+	dev->absinfo = kcalloc(ABS_CNT, sizeof(*dev->absinfo), GFP_KERNEL);
+	if (!dev->absinfo) {
+		dev_err(dev->dev.parent ?: &dev->dev,
+			"%s: unable to allocate memory\n", __func__);
+		/*
+		 * We will handle this allocation failure in
+		 * input_register_device() when we refuse to register input
+		 * device with ABS bits but without absinfo.
+		 */
+	}
 }
 EXPORT_SYMBOL(input_alloc_absinfo);
 

drivers/input/joystick/a3d.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/adi.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/joystick/amijoy.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/types.h>

drivers/input/joystick/analog.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/joystick/cobra.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/db9.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>
@@ -263,6 +259,7 @@ static unsigned char db9_saturn_read_packet(struct parport *port, unsigned char
 			db9_saturn_write_sub(port, type, 3, powered, 0);
 			return data[0] = 0xe3;
 		}
+		/* else: fall through */
 	default:
 		return data[0];
 	}
@@ -282,11 +279,14 @@ static int db9_saturn_report(unsigned char id, unsigned char data[60], struct in
 		switch (data[j]) {
 		case 0x16: /* multi controller (analog 4 axis) */
 			input_report_abs(dev, db9_abs[5], data[j + 6]);
+			/* fall through */
 		case 0x15: /* mission stick (analog 3 axis) */
 			input_report_abs(dev, db9_abs[3], data[j + 4]);
 			input_report_abs(dev, db9_abs[4], data[j + 5]);
+			/* fall through */
 		case 0x13: /* racing controller (analog 1 axis) */
 			input_report_abs(dev, db9_abs[2], data[j + 3]);
+			/* fall through */
 		case 0x34: /* saturn keyboard (udlr ZXC ASD QE Esc) */
 		case 0x02: /* digital pad (digital 2 axis + buttons) */
 			input_report_abs(dev, db9_abs[0], !(data[j + 1] & 128) - !(data[j + 1] & 64));
@@ -380,6 +380,7 @@ static void db9_timer(struct timer_list *t)
 			input_report_abs(dev2, ABS_X, (data & DB9_RIGHT ? 0 : 1) - (data & DB9_LEFT ? 0 : 1));
 			input_report_abs(dev2, ABS_Y, (data & DB9_DOWN  ? 0 : 1) - (data & DB9_UP   ? 0 : 1));
 			input_report_key(dev2, BTN_TRIGGER, ~data & DB9_FIRE1);
+			/* fall through */
 
 		case DB9_MULTI_0802:
 

drivers/input/joystick/gamecon.c

@@ -24,10 +24,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

drivers/input/joystick/gf2k.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/joystick/grip.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/guillemot.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/iforce/iforce-ff.c

@@ -19,10 +19,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include "iforce.h"
@@ -56,7 +52,7 @@ static int make_magnitude_modifier(struct iforce* iforce,
 
 	iforce_send_packet(iforce, FF_CMD_MAGNITUDE, data);
 
-	iforce_dump_packet("magnitude: ", FF_CMD_MAGNITUDE, data);
+	iforce_dump_packet(iforce, "magnitude", FF_CMD_MAGNITUDE, data);
 	return 0;
 }
 
@@ -178,7 +174,7 @@ static int make_condition_modifier(struct iforce* iforce,
 	data[9] = (100 * lsat) >> 16;
 
 	iforce_send_packet(iforce, FF_CMD_CONDITION, data);
-	iforce_dump_packet("condition", FF_CMD_CONDITION, data);
+	iforce_dump_packet(iforce, "condition", FF_CMD_CONDITION, data);
 
 	return 0;
 }

drivers/input/joystick/iforce/iforce-main.c

@@ -19,10 +19,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include "iforce.h"
@@ -33,21 +29,14 @@ MODULE_LICENSE("GPL");
 
 static signed short btn_joystick[] =
 { BTN_TRIGGER, BTN_TOP, BTN_THUMB, BTN_TOP2, BTN_BASE,
-  BTN_BASE2, BTN_BASE3, BTN_BASE4, BTN_BASE5, BTN_A, BTN_B, BTN_C, -1 };
+  BTN_BASE2, BTN_BASE3, BTN_BASE4, BTN_BASE5, BTN_A,
+  BTN_B, BTN_C, BTN_DEAD, -1 };
 
-static signed short btn_avb_pegasus[] =
+static signed short btn_joystick_avb[] =
-{ BTN_TRIGGER, BTN_TOP, BTN_THUMB, BTN_TOP2, BTN_BASE,
+{ BTN_TRIGGER, BTN_THUMB, BTN_TOP, BTN_TOP2, BTN_BASE,
-  BTN_BASE2, BTN_BASE3, BTN_BASE4, -1 };
+  BTN_BASE2, BTN_BASE3, BTN_BASE4, BTN_DEAD, -1 };
 
 static signed short btn_wheel[] =
-{ BTN_TRIGGER, BTN_TOP, BTN_THUMB, BTN_TOP2, BTN_BASE,
-  BTN_BASE2, BTN_BASE3, BTN_BASE4, BTN_BASE5, BTN_A, BTN_B, BTN_C, -1 };
-
-static signed short btn_avb_tw[] =
-{ BTN_TRIGGER, BTN_THUMB, BTN_TOP, BTN_TOP2, BTN_BASE,
-  BTN_BASE2, BTN_BASE3, BTN_BASE4, -1 };
-
-static signed short btn_avb_wheel[] =
 { BTN_GEAR_DOWN, BTN_GEAR_UP, BTN_BASE, BTN_BASE2, BTN_BASE3,
   BTN_BASE4, BTN_BASE5, BTN_BASE6, -1 };
 
@@ -73,9 +62,9 @@ static struct iforce_device iforce_device[] = {
 	{ 0x044f, 0xa01c, "Thrustmaster Motor Sport GT",		btn_wheel, abs_wheel, ff_iforce },
 	{ 0x046d, 0xc281, "Logitech WingMan Force",			btn_joystick, abs_joystick, ff_iforce },
 	{ 0x046d, 0xc291, "Logitech WingMan Formula Force",		btn_wheel, abs_wheel, ff_iforce },
-	{ 0x05ef, 0x020a, "AVB Top Shot Pegasus",			btn_avb_pegasus, abs_avb_pegasus, ff_iforce },
+	{ 0x05ef, 0x020a, "AVB Top Shot Pegasus",			btn_joystick_avb, abs_avb_pegasus, ff_iforce },
-	{ 0x05ef, 0x8884, "AVB Mag Turbo Force",			btn_avb_wheel, abs_wheel, ff_iforce },
+	{ 0x05ef, 0x8884, "AVB Mag Turbo Force",			btn_wheel, abs_wheel, ff_iforce },
-	{ 0x05ef, 0x8888, "AVB Top Shot Force Feedback Racing Wheel",	btn_avb_tw, abs_wheel, ff_iforce }, //?
+	{ 0x05ef, 0x8888, "AVB Top Shot Force Feedback Racing Wheel",	btn_wheel, abs_wheel, ff_iforce }, //?
 	{ 0x061c, 0xc0a4, "ACT LABS Force RS",                          btn_wheel, abs_wheel, ff_iforce }, //?
 	{ 0x061c, 0xc084, "ACT LABS Force RS",				btn_wheel, abs_wheel, ff_iforce },
 	{ 0x06f8, 0x0001, "Guillemot Race Leader Force Feedback",	btn_wheel, abs_wheel, ff_iforce }, //?
@@ -360,7 +349,7 @@ int iforce_init_device(struct iforce *iforce)
 
 	for (i = 0; c[i]; i++)
 		if (!iforce_get_id_packet(iforce, c + i))
-			iforce_dump_packet("info", iforce->ecmd, iforce->edata);
+			iforce_dump_packet(iforce, "info", iforce->ecmd, iforce->edata);
 
 /*
  * Disable spring, enable force feedback.
@@ -388,7 +377,6 @@ int iforce_init_device(struct iforce *iforce)
 
 	for (i = 0; iforce->type->btn[i] >= 0; i++)
 		set_bit(iforce->type->btn[i], input_dev->keybit);
-	set_bit(BTN_DEAD, input_dev->keybit);
 
 	for (i = 0; iforce->type->abs[i] >= 0; i++) {
 

drivers/input/joystick/iforce/iforce-packets.c

@@ -19,10 +19,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include "iforce.h"
@@ -33,14 +29,10 @@ static struct {
 } iforce_hat_to_axis[16] = {{ 0,-1}, { 1,-1}, { 1, 0}, { 1, 1}, { 0, 1}, {-1, 1}, {-1, 0}, {-1,-1}};
 
 
-void iforce_dump_packet(char *msg, u16 cmd, unsigned char *data)
+void iforce_dump_packet(struct iforce *iforce, char *msg, u16 cmd, unsigned char *data)
 {
-	int i;
+	dev_dbg(iforce->dev->dev.parent, "%s %s cmd = %04x, data = %*ph\n",
-
+		__func__, msg, cmd, LO(cmd), data);
-	printk(KERN_DEBUG __FILE__ ": %s cmd = %04x, data = ", msg, cmd);
-	for (i = 0; i < LO(cmd); i++)
-		printk("%02x ", data[i]);
-	printk("\n");
 }
 
 /*
@@ -255,7 +247,7 @@ int iforce_get_id_packet(struct iforce *iforce, char *packet)
 		iforce->cr.bRequest = packet[0];
 		iforce->ctrl->dev = iforce->usbdev;
 
-		status = usb_submit_urb(iforce->ctrl, GFP_ATOMIC);
+		status = usb_submit_urb(iforce->ctrl, GFP_KERNEL);
 		if (status) {
 			dev_err(&iforce->intf->dev,
 				"usb_submit_urb failed %d\n", status);

drivers/input/joystick/iforce/iforce-serio.c

@@ -19,10 +19,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include "iforce.h"

drivers/input/joystick/iforce/iforce-usb.c

@@ -19,10 +19,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include "iforce.h"

drivers/input/joystick/iforce/iforce.h

@@ -19,10 +19,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>
@@ -158,7 +154,7 @@ int iforce_init_device(struct iforce *iforce);
 int iforce_control_playback(struct iforce*, u16 id, unsigned int);
 void iforce_process_packet(struct iforce *iforce, u16 cmd, unsigned char *data);
 int iforce_send_packet(struct iforce *iforce, u16 cmd, unsigned char* data);
-void iforce_dump_packet(char *msg, u16 cmd, unsigned char *data) ;
+void iforce_dump_packet(struct iforce *iforce, char *msg, u16 cmd, unsigned char *data);
 int iforce_get_id_packet(struct iforce *iforce, char *packet);
 
 /* iforce-ff.c */

drivers/input/joystick/interact.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/joydump.c

@@ -21,10 +21,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/joystick/magellan.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- *  Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/pxrc.c

@@ -3,7 +3,6 @@
  * Driver for Phoenix RC Flight Controller Adapter
  *
  * Copyright (C) 2018 Marcus Folkesson <marcus.folkesson@gmail.com>
- *
  */
 
 #include <linux/kernel.h>
@@ -16,31 +15,22 @@
 #include <linux/mutex.h>
 #include <linux/input.h>
 
-#define PXRC_VENDOR_ID	(0x1781)
+#define PXRC_VENDOR_ID		0x1781
-#define PXRC_PRODUCT_ID	(0x0898)
+#define PXRC_PRODUCT_ID		0x0898
-
-static const struct usb_device_id pxrc_table[] = {
-	{ USB_DEVICE(PXRC_VENDOR_ID, PXRC_PRODUCT_ID) },
-	{ }
-};
-MODULE_DEVICE_TABLE(usb, pxrc_table);
 
 struct pxrc {
 	struct input_dev	*input;
-	struct usb_device	*udev;
 	struct usb_interface	*intf;
 	struct urb		*urb;
 	struct mutex		pm_mutex;
 	bool			is_open;
-	__u8			epaddr;
 	char			phys[64];
-	unsigned char           *data;
-	size_t			bsize;
 };
 
 static void pxrc_usb_irq(struct urb *urb)
 {
 	struct pxrc *pxrc = urb->context;
+	u8 *data = urb->transfer_buffer;
 	int error;
 
 	switch (urb->status) {
@@ -68,15 +58,15 @@ static void pxrc_usb_irq(struct urb *urb)
 	}
 
 	if (urb->actual_length == 8) {
-		input_report_abs(pxrc->input, ABS_X, pxrc->data[0]);
+		input_report_abs(pxrc->input, ABS_X, data[0]);
-		input_report_abs(pxrc->input, ABS_Y, pxrc->data[2]);
+		input_report_abs(pxrc->input, ABS_Y, data[2]);
-		input_report_abs(pxrc->input, ABS_RX, pxrc->data[3]);
+		input_report_abs(pxrc->input, ABS_RX, data[3]);
-		input_report_abs(pxrc->input, ABS_RY, pxrc->data[4]);
+		input_report_abs(pxrc->input, ABS_RY, data[4]);
-		input_report_abs(pxrc->input, ABS_RUDDER, pxrc->data[5]);
+		input_report_abs(pxrc->input, ABS_RUDDER, data[5]);
-		input_report_abs(pxrc->input, ABS_THROTTLE, pxrc->data[6]);
+		input_report_abs(pxrc->input, ABS_THROTTLE, data[6]);
-		input_report_abs(pxrc->input, ABS_MISC, pxrc->data[7]);
+		input_report_abs(pxrc->input, ABS_MISC, data[7]);
 
-		input_report_key(pxrc->input, BTN_A, pxrc->data[1]);
+		input_report_key(pxrc->input, BTN_A, data[1]);
 	}
 
 exit:
@@ -120,61 +110,73 @@ static void pxrc_close(struct input_dev *input)
 	mutex_unlock(&pxrc->pm_mutex);
 }
 
-static int pxrc_usb_init(struct pxrc *pxrc)
+static void pxrc_free_urb(void *_pxrc)
 {
-	struct usb_endpoint_descriptor *epirq;
+	struct pxrc *pxrc = _pxrc;
-	unsigned int pipe;
-	int retval;
-
-	/* Set up the endpoint information */
-	/* This device only has an interrupt endpoint */
-	retval = usb_find_common_endpoints(pxrc->intf->cur_altsetting,
-			NULL, NULL, &epirq, NULL);
-	if (retval) {
-		dev_err(&pxrc->intf->dev,
-			"Could not find endpoint\n");
-		goto error;
-	}
-
-	pxrc->bsize = usb_endpoint_maxp(epirq);
-	pxrc->epaddr = epirq->bEndpointAddress;
-	pxrc->data = devm_kmalloc(&pxrc->intf->dev, pxrc->bsize, GFP_KERNEL);
-	if (!pxrc->data) {
-		retval = -ENOMEM;
-		goto error;
-	}
-
-	usb_set_intfdata(pxrc->intf, pxrc);
-	usb_make_path(pxrc->udev, pxrc->phys, sizeof(pxrc->phys));
-	strlcat(pxrc->phys, "/input0", sizeof(pxrc->phys));
-
-	pxrc->urb = usb_alloc_urb(0, GFP_KERNEL);
-	if (!pxrc->urb) {
-		retval = -ENOMEM;
-		goto error;
-	}
-
-	pipe = usb_rcvintpipe(pxrc->udev, pxrc->epaddr),
-	usb_fill_int_urb(pxrc->urb, pxrc->udev, pipe, pxrc->data, pxrc->bsize,
-						pxrc_usb_irq, pxrc, 1);
-
-error:
-	return retval;
-
 
+	usb_free_urb(pxrc->urb);
 }
 
-static int pxrc_input_init(struct pxrc *pxrc)
+static int pxrc_probe(struct usb_interface *intf,
+		      const struct usb_device_id *id)
 {
-	pxrc->input = devm_input_allocate_device(&pxrc->intf->dev);
+	struct usb_device *udev = interface_to_usbdev(intf);
-	if (pxrc->input == NULL) {
+	struct pxrc *pxrc;
-		dev_err(&pxrc->intf->dev, "couldn't allocate input device\n");
+	struct usb_endpoint_descriptor *epirq;
+	size_t xfer_size;
+	void *xfer_buf;
+	int error;
+
+	/*
+	 * Locate the endpoint information. This device only has an
+	 * interrupt endpoint.
+	 */
+	error = usb_find_common_endpoints(intf->cur_altsetting,
+					  NULL, NULL, &epirq, NULL);
+	if (error) {
+		dev_err(&intf->dev, "Could not find endpoint\n");
+		return error;
+	}
+
+	pxrc = devm_kzalloc(&intf->dev, sizeof(*pxrc), GFP_KERNEL);
+	if (!pxrc)
+		return -ENOMEM;
+
+	mutex_init(&pxrc->pm_mutex);
+	pxrc->intf = intf;
+
+	usb_set_intfdata(pxrc->intf, pxrc);
+
+	xfer_size = usb_endpoint_maxp(epirq);
+	xfer_buf = devm_kmalloc(&intf->dev, xfer_size, GFP_KERNEL);
+	if (!xfer_buf)
+		return -ENOMEM;
+
+	pxrc->urb = usb_alloc_urb(0, GFP_KERNEL);
+	if (!pxrc->urb)
+		return -ENOMEM;
+
+	error = devm_add_action_or_reset(&intf->dev, pxrc_free_urb, pxrc);
+	if (error)
+		return error;
+
+	usb_fill_int_urb(pxrc->urb, udev,
+			 usb_rcvintpipe(udev, epirq->bEndpointAddress),
+			 xfer_buf, xfer_size, pxrc_usb_irq, pxrc, 1);
+
+	pxrc->input = devm_input_allocate_device(&intf->dev);
+	if (!pxrc->input) {
+		dev_err(&intf->dev, "couldn't allocate input device\n");
 		return -ENOMEM;
 	}
 
 	pxrc->input->name = "PXRC Flight Controller Adapter";
+
+	usb_make_path(udev, pxrc->phys, sizeof(pxrc->phys));
+	strlcat(pxrc->phys, "/input0", sizeof(pxrc->phys));
 	pxrc->input->phys = pxrc->phys;
-	usb_to_input_id(pxrc->udev, &pxrc->input->id);
+
+	usb_to_input_id(udev, &pxrc->input->id);
 
 	pxrc->input->open = pxrc_open;
 	pxrc->input->close = pxrc_close;
@@ -190,46 +192,16 @@ static int pxrc_input_init(struct pxrc *pxrc)
 
 	input_set_drvdata(pxrc->input, pxrc);
 
-	return input_register_device(pxrc->input);
+	error = input_register_device(pxrc->input);
-}
+	if (error)
-
+		return error;
-static int pxrc_probe(struct usb_interface *intf,
-		      const struct usb_device_id *id)
-{
-	struct pxrc *pxrc;
-	int retval;
-
-	pxrc = devm_kzalloc(&intf->dev, sizeof(*pxrc), GFP_KERNEL);
-	if (!pxrc)
-		return -ENOMEM;
-
-	mutex_init(&pxrc->pm_mutex);
-	pxrc->udev = usb_get_dev(interface_to_usbdev(intf));
-	pxrc->intf = intf;
-
-	retval = pxrc_usb_init(pxrc);
-	if (retval)
-		goto error;
-
-	retval = pxrc_input_init(pxrc);
-	if (retval)
-		goto err_free_urb;
 
 	return 0;
-
-err_free_urb:
-	usb_free_urb(pxrc->urb);
-
-error:
-	return retval;
 }
 
 static void pxrc_disconnect(struct usb_interface *intf)
 {
-	struct pxrc *pxrc = usb_get_intfdata(intf);
+	/* All driver resources are devm-managed. */
-
-	usb_free_urb(pxrc->urb);
-	usb_set_intfdata(intf, NULL);
 }
 
 static int pxrc_suspend(struct usb_interface *intf, pm_message_t message)
@@ -284,6 +256,12 @@ static int pxrc_reset_resume(struct usb_interface *intf)
 	return pxrc_resume(intf);
 }
 
+static const struct usb_device_id pxrc_table[] = {
+	{ USB_DEVICE(PXRC_VENDOR_ID, PXRC_PRODUCT_ID) },
+	{ }
+};
+MODULE_DEVICE_TABLE(usb, pxrc_table);
+
 static struct usb_driver pxrc_driver = {
 	.name =		"pxrc",
 	.probe =	pxrc_probe,

drivers/input/joystick/sidewinder.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/joystick/spaceball.c

@@ -24,10 +24,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- *  Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/spaceorb.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- *  Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/stinger.c

@@ -21,10 +21,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- *  Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/tmdc.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/joystick/turbografx.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/joystick/warrior.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- *  Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/kernel.h>

drivers/input/keyboard/adp5589-keys.c

@@ -885,6 +885,7 @@ static int adp5589_probe(struct i2c_client *client,
 	switch (id->driver_data) {
 	case ADP5585_02:
 		kpad->support_row5 = true;
+		/* fall through */
 	case ADP5585_01:
 		kpad->is_adp5585 = true;
 		kpad->var = &const_adp5585;

drivers/input/keyboard/amikbd.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/keyboard/atakbd.c

@@ -34,10 +34,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/keyboard/cros_ec_keyb.c

@@ -1,25 +1,15 @@
-/*
+// SPDX-License-Identifier: GPL-2.0
- * ChromeOS EC keyboard driver
+// ChromeOS EC keyboard driver
- *
+//
- * Copyright (C) 2012 Google, Inc
+// Copyright (C) 2012 Google, Inc.
- *
+//
- * This software is licensed under the terms of the GNU General Public
+// This driver uses the ChromeOS EC byte-level message-based protocol for
- * License version 2, as published by the Free Software Foundation, and
+// communicating the keyboard state (which keys are pressed) from a keyboard EC
- * may be copied, distributed, and modified under those terms.
+// to the AP over some bus (such as i2c, lpc, spi).  The EC does debouncing,
- *
+// but everything else (including deghosting) is done here.  The main
- * This program is distributed in the hope that it will be useful,
+// motivation for this is to keep the EC firmware as simple as possible, since
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
+// it cannot be easily upgraded and EC flash/IRAM space is relatively
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+// expensive.
- * GNU General Public License for more details.
- *
- * This driver uses the Chrome OS EC byte-level message-based protocol for
- * communicating the keyboard state (which keys are pressed) from a keyboard EC
- * to the AP over some bus (such as i2c, lpc, spi).  The EC does debouncing,
- * but everything else (including deghosting) is done here.  The main
- * motivation for this is to keep the EC firmware as simple as possible, since
- * it cannot be easily upgraded and EC flash/IRAM space is relatively
- * expensive.
- */
 
 #include <linux/module.h>
 #include <linux/bitops.h>
@@ -170,9 +160,6 @@ static void cros_ec_keyb_process(struct cros_ec_keyb *ckdev,
 	int col, row;
 	int new_state;
 	int old_state;
-	int num_cols;
-
-	num_cols = len;
 
 	if (ckdev->ghost_filter && cros_ec_keyb_has_ghosting(ckdev, kb_state)) {
 		/*
@@ -242,19 +229,17 @@ static int cros_ec_keyb_work(struct notifier_block *nb,
 	u32 val;
 	unsigned int ev_type;
 
+	/*
+	 * If not wake enabled, discard key state changes during
+	 * suspend. Switches will be re-checked in
+	 * cros_ec_keyb_resume() to be sure nothing is lost.
+	 */
+	if (queued_during_suspend && !device_may_wakeup(ckdev->dev))
+		return NOTIFY_OK;
+
 	switch (ckdev->ec->event_data.event_type) {
 	case EC_MKBP_EVENT_KEY_MATRIX:
-		if (device_may_wakeup(ckdev->dev)) {
+		pm_wakeup_event(ckdev->dev, 0);
-			pm_wakeup_event(ckdev->dev, 0);
-		} else {
-			/*
-			 * If keyboard is not wake enabled, discard key state
-			 * changes during suspend. Switches will be re-checked
-			 * in cros_ec_keyb_resume() to be sure nothing is lost.
-			 */
-			if (queued_during_suspend)
-				return NOTIFY_OK;
-		}
 
 		if (ckdev->ec->event_size != ckdev->cols) {
 			dev_err(ckdev->dev,
@@ -268,10 +253,7 @@ static int cros_ec_keyb_work(struct notifier_block *nb,
 		break;
 
 	case EC_MKBP_EVENT_SYSRQ:
-		if (device_may_wakeup(ckdev->dev))
+		pm_wakeup_event(ckdev->dev, 0);
-			pm_wakeup_event(ckdev->dev, 0);
-		else if (queued_during_suspend)
-			return NOTIFY_OK;
 
 		val = get_unaligned_le32(&ckdev->ec->event_data.data.sysrq);
 		dev_dbg(ckdev->dev, "sysrq code from EC: %#x\n", val);
@@ -280,10 +262,7 @@ static int cros_ec_keyb_work(struct notifier_block *nb,
 
 	case EC_MKBP_EVENT_BUTTON:
 	case EC_MKBP_EVENT_SWITCH:
-		if (device_may_wakeup(ckdev->dev))
+		pm_wakeup_event(ckdev->dev, 0);
-			pm_wakeup_event(ckdev->dev, 0);
-		else if (queued_during_suspend)
-			return NOTIFY_OK;
 
 		if (ckdev->ec->event_data.event_type == EC_MKBP_EVENT_BUTTON) {
 			val = get_unaligned_le32(
@@ -683,6 +662,6 @@ static struct platform_driver cros_ec_keyb_driver = {
 
 module_platform_driver(cros_ec_keyb_driver);
 
-MODULE_LICENSE("GPL");
+MODULE_LICENSE("GPL v2");
 MODULE_DESCRIPTION("ChromeOS EC keyboard driver");
 MODULE_ALIAS("platform:cros-ec-keyb");

drivers/input/keyboard/gpio_keys.c

@@ -196,7 +196,7 @@ static ssize_t gpio_keys_attr_show_helper(struct gpio_keys_drvdata *ddata,
 	ssize_t ret;
 	int i;
 
-	bits = kcalloc(BITS_TO_LONGS(n_events), sizeof(*bits), GFP_KERNEL);
+	bits = bitmap_zalloc(n_events, GFP_KERNEL);
 	if (!bits)
 		return -ENOMEM;
 
@@ -216,7 +216,7 @@ static ssize_t gpio_keys_attr_show_helper(struct gpio_keys_drvdata *ddata,
 	buf[ret++] = '\n';
 	buf[ret] = '\0';
 
-	kfree(bits);
+	bitmap_free(bits);
 
 	return ret;
 }
@@ -240,7 +240,7 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 	ssize_t error;
 	int i;
 
-	bits = kcalloc(BITS_TO_LONGS(n_events), sizeof(*bits), GFP_KERNEL);
+	bits = bitmap_zalloc(n_events, GFP_KERNEL);
 	if (!bits)
 		return -ENOMEM;
 
@@ -284,7 +284,7 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 	mutex_unlock(&ddata->disable_lock);
 
 out:
-	kfree(bits);
+	bitmap_free(bits);
 	return error;
 }
 

drivers/input/keyboard/imx_keypad.c

@@ -1,11 +1,7 @@
-/*
+// SPDX-License-Identifier: GPL-2.0
- * Driver for the IMX keypad port.
+//
- * Copyright (C) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
+// Driver for the IMX keypad port.
- *
+// Copyright (C) 2009 Alberto Panizzo <maramaopercheseimorto@gmail.com>
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
 
 #include <linux/clk.h>
 #include <linux/delay.h>

drivers/input/keyboard/newtonkbd.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <j.cormack@doc.ic.ac.uk>, or by paper mail:
- * Justin Cormack, 68 Dartmouth Park Road, London NW5 1SN, UK.
  */
 
 #include <linux/slab.h>

drivers/input/keyboard/snvs_pwrkey.c

@@ -1,14 +1,7 @@
-/*
+// SPDX-License-Identifier: GPL-2.0+
- * Driver for the IMX SNVS ON/OFF Power Key
+//
- * Copyright (C) 2015 Freescale Semiconductor, Inc. All Rights Reserved.
+// Driver for the IMX SNVS ON/OFF Power Key
- *
+// Copyright (C) 2015 Freescale Semiconductor, Inc. All Rights Reserved.
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
 
 #include <linux/device.h>
 #include <linux/err.h>

drivers/input/keyboard/stowaway.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <marek.vasut@gmail.com>, or by paper mail:
- * Marek Vasut, Liskovecka 559, Frydek-Mistek, 738 01 Czech Republic
  */
 
 #include <linux/slab.h>

drivers/input/keyboard/sunkbd.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/keyboard/xtkbd.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/slab.h>

drivers/input/misc/keyspan_remote.c

@@ -466,7 +466,7 @@ static int keyspan_probe(struct usb_interface *interface, const struct usb_devic
 	remote->in_endpoint = endpoint;
 	remote->toggle = -1;	/* Set to -1 so we will always not match the toggle from the first remote message. */
 
-	remote->in_buffer = usb_alloc_coherent(udev, RECV_SIZE, GFP_ATOMIC, &remote->in_dma);
+	remote->in_buffer = usb_alloc_coherent(udev, RECV_SIZE, GFP_KERNEL, &remote->in_dma);
 	if (!remote->in_buffer) {
 		error = -ENOMEM;
 		goto fail1;

drivers/input/misc/pm8941-pwrkey.c

@@ -20,6 +20,7 @@
 #include <linux/log2.h>
 #include <linux/module.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/reboot.h>
 #include <linux/regmap.h>
@@ -28,6 +29,7 @@
 
 #define PON_RT_STS			0x10
 #define  PON_KPDPWR_N_SET		BIT(0)
+#define  PON_RESIN_N_SET		BIT(1)
 
 #define PON_PS_HOLD_RST_CTL		0x5a
 #define PON_PS_HOLD_RST_CTL2		0x5b
@@ -38,10 +40,15 @@
 
 #define PON_PULL_CTL			0x70
 #define  PON_KPDPWR_PULL_UP		BIT(1)
+#define  PON_RESIN_PULL_UP		BIT(0)
 
 #define PON_DBC_CTL			0x71
 #define  PON_DBC_DELAY_MASK		0x7
 
+struct pm8941_data {
+	unsigned int pull_up_bit;
+	unsigned int status_bit;
+};
 
 struct pm8941_pwrkey {
 	struct device *dev;
@@ -52,6 +59,9 @@ struct pm8941_pwrkey {
 
 	unsigned int revision;
 	struct notifier_block reboot_notifier;
+
+	u32 code;
+	const struct pm8941_data *data;
 };
 
 static int pm8941_reboot_notify(struct notifier_block *nb,
@@ -124,7 +134,8 @@ static irqreturn_t pm8941_pwrkey_irq(int irq, void *_data)
 	if (error)
 		return IRQ_HANDLED;
 
-	input_report_key(pwrkey->input, KEY_POWER, !!(sts & PON_KPDPWR_N_SET));
+	input_report_key(pwrkey->input, pwrkey->code,
+			 sts & pwrkey->data->status_bit);
 	input_sync(pwrkey->input);
 
 	return IRQ_HANDLED;
@@ -157,6 +168,7 @@ static int pm8941_pwrkey_probe(struct platform_device *pdev)
 {
 	struct pm8941_pwrkey *pwrkey;
 	bool pull_up;
+	struct device *parent;
 	u32 req_delay;
 	int error;
 
@@ -175,12 +187,30 @@ static int pm8941_pwrkey_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	pwrkey->dev = &pdev->dev;
+	pwrkey->data = of_device_get_match_data(&pdev->dev);
 
-	pwrkey->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	parent = pdev->dev.parent;
+	pwrkey->regmap = dev_get_regmap(parent, NULL);
 	if (!pwrkey->regmap) {
-		dev_err(&pdev->dev, "failed to locate regmap\n");
+		/*
-		return -ENODEV;
+		 * We failed to get regmap for parent. Let's see if we are
+		 * a child of pon node and read regmap and reg from its
+		 * parent.
+		 */
+		pwrkey->regmap = dev_get_regmap(parent->parent, NULL);
+		if (!pwrkey->regmap) {
+			dev_err(&pdev->dev, "failed to locate regmap\n");
+			return -ENODEV;
+		}
+
+		error = of_property_read_u32(parent->of_node,
+					     "reg", &pwrkey->baseaddr);
+	} else {
+		error = of_property_read_u32(pdev->dev.of_node, "reg",
+					     &pwrkey->baseaddr);
 	}
+	if (error)
+		return error;
 
 	pwrkey->irq = platform_get_irq(pdev, 0);
 	if (pwrkey->irq < 0) {
@@ -188,11 +218,6 @@ static int pm8941_pwrkey_probe(struct platform_device *pdev)
 		return pwrkey->irq;
 	}
 
-	error = of_property_read_u32(pdev->dev.of_node, "reg",
-				     &pwrkey->baseaddr);
-	if (error)
-		return error;
-
 	error = regmap_read(pwrkey->regmap, pwrkey->baseaddr + PON_REV2,
 			    &pwrkey->revision);
 	if (error) {
@@ -200,13 +225,21 @@ static int pm8941_pwrkey_probe(struct platform_device *pdev)
 		return error;
 	}
 
+	error = of_property_read_u32(pdev->dev.of_node, "linux,code",
+				     &pwrkey->code);
+	if (error) {
+		dev_dbg(&pdev->dev,
+			"no linux,code assuming power (%d)\n", error);
+		pwrkey->code = KEY_POWER;
+	}
+
 	pwrkey->input = devm_input_allocate_device(&pdev->dev);
 	if (!pwrkey->input) {
 		dev_dbg(&pdev->dev, "unable to allocate input device\n");
 		return -ENOMEM;
 	}
 
-	input_set_capability(pwrkey->input, EV_KEY, KEY_POWER);
+	input_set_capability(pwrkey->input, EV_KEY, pwrkey->code);
 
 	pwrkey->input->name = "pm8941_pwrkey";
 	pwrkey->input->phys = "pm8941_pwrkey/input0";
@@ -225,8 +258,8 @@ static int pm8941_pwrkey_probe(struct platform_device *pdev)
 
 	error = regmap_update_bits(pwrkey->regmap,
 				   pwrkey->baseaddr + PON_PULL_CTL,
-				   PON_KPDPWR_PULL_UP,
+				   pwrkey->data->pull_up_bit,
-				   pull_up ? PON_KPDPWR_PULL_UP : 0);
+				   pull_up ? pwrkey->data->pull_up_bit : 0);
 	if (error) {
 		dev_err(&pdev->dev, "failed to set pull: %d\n", error);
 		return error;
@@ -271,8 +304,19 @@ static int pm8941_pwrkey_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct pm8941_data pwrkey_data = {
+	.pull_up_bit = PON_KPDPWR_PULL_UP,
+	.status_bit = PON_KPDPWR_N_SET,
+};
+
+static const struct pm8941_data resin_data = {
+	.pull_up_bit = PON_RESIN_PULL_UP,
+	.status_bit = PON_RESIN_N_SET,
+};
+
 static const struct of_device_id pm8941_pwr_key_id_table[] = {
-	{ .compatible = "qcom,pm8941-pwrkey" },
+	{ .compatible = "qcom,pm8941-pwrkey", .data = &pwrkey_data },
+	{ .compatible = "qcom,pm8941-resin", .data = &resin_data },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, pm8941_pwr_key_id_table);

drivers/input/misc/powermate.c

@@ -277,7 +277,7 @@ static int powermate_input_event(struct input_dev *dev, unsigned int type, unsig
 static int powermate_alloc_buffers(struct usb_device *udev, struct powermate_device *pm)
 {
 	pm->data = usb_alloc_coherent(udev, POWERMATE_PAYLOAD_SIZE_MAX,
-				      GFP_ATOMIC, &pm->data_dma);
+				      GFP_KERNEL, &pm->data_dma);
 	if (!pm->data)
 		return -1;
 

drivers/input/misc/xen-kbdfront.c

@@ -63,6 +63,9 @@ static void xenkbd_disconnect_backend(struct xenkbd_info *);
 static void xenkbd_handle_motion_event(struct xenkbd_info *info,
 				       struct xenkbd_motion *motion)
 {
+	if (unlikely(!info->ptr))
+		return;
+
 	input_report_rel(info->ptr, REL_X, motion->rel_x);
 	input_report_rel(info->ptr, REL_Y, motion->rel_y);
 	if (motion->rel_z)
@@ -73,6 +76,9 @@ static void xenkbd_handle_motion_event(struct xenkbd_info *info,
 static void xenkbd_handle_position_event(struct xenkbd_info *info,
 					 struct xenkbd_position *pos)
 {
+	if (unlikely(!info->ptr))
+		return;
+
 	input_report_abs(info->ptr, ABS_X, pos->abs_x);
 	input_report_abs(info->ptr, ABS_Y, pos->abs_y);
 	if (pos->rel_z)
@@ -97,6 +103,9 @@ static void xenkbd_handle_key_event(struct xenkbd_info *info,
 		return;
 	}
 
+	if (unlikely(!dev))
+		return;
+
 	input_event(dev, EV_KEY, key->keycode, value);
 	input_sync(dev);
 }
@@ -192,7 +201,7 @@ static int xenkbd_probe(struct xenbus_device *dev,
 				  const struct xenbus_device_id *id)
 {
 	int ret, i;
-	unsigned int abs, touch;
+	bool with_mtouch, with_kbd, with_ptr;
 	struct xenkbd_info *info;
 	struct input_dev *kbd, *ptr, *mtouch;
 
@@ -211,106 +220,127 @@ static int xenkbd_probe(struct xenbus_device *dev,
 	if (!info->page)
 		goto error_nomem;
 
-	/* Set input abs params to match backend screen res */
+	/*
-	abs = xenbus_read_unsigned(dev->otherend,
+	 * The below are reverse logic, e.g. if the feature is set, then
-				   XENKBD_FIELD_FEAT_ABS_POINTER, 0);
+	 * do not expose the corresponding virtual device.
-	ptr_size[KPARAM_X] = xenbus_read_unsigned(dev->otherend,
+	 */
-						  XENKBD_FIELD_WIDTH,
+	with_kbd = !xenbus_read_unsigned(dev->otherend,
-						  ptr_size[KPARAM_X]);
+					 XENKBD_FIELD_FEAT_DSBL_KEYBRD, 0);
-	ptr_size[KPARAM_Y] = xenbus_read_unsigned(dev->otherend,
-						  XENKBD_FIELD_HEIGHT,
-						  ptr_size[KPARAM_Y]);
-	if (abs) {
-		ret = xenbus_write(XBT_NIL, dev->nodename,
-				   XENKBD_FIELD_REQ_ABS_POINTER, "1");
-		if (ret) {
-			pr_warn("xenkbd: can't request abs-pointer\n");
-			abs = 0;
-		}
-	}
 
-	touch = xenbus_read_unsigned(dev->nodename,
+	with_ptr = !xenbus_read_unsigned(dev->otherend,
-				     XENKBD_FIELD_FEAT_MTOUCH, 0);
+					 XENKBD_FIELD_FEAT_DSBL_POINTER, 0);
-	if (touch) {
+
+	/* Direct logic: if set, then create multi-touch device. */
+	with_mtouch = xenbus_read_unsigned(dev->otherend,
+					   XENKBD_FIELD_FEAT_MTOUCH, 0);
+	if (with_mtouch) {
 		ret = xenbus_write(XBT_NIL, dev->nodename,
 				   XENKBD_FIELD_REQ_MTOUCH, "1");
 		if (ret) {
 			pr_warn("xenkbd: can't request multi-touch");
-			touch = 0;
+			with_mtouch = 0;
 		}
 	}
 
 	/* keyboard */
-	kbd = input_allocate_device();
+	if (with_kbd) {
-	if (!kbd)
+		kbd = input_allocate_device();
-		goto error_nomem;
+		if (!kbd)
-	kbd->name = "Xen Virtual Keyboard";
+			goto error_nomem;
-	kbd->phys = info->phys;
+		kbd->name = "Xen Virtual Keyboard";
-	kbd->id.bustype = BUS_PCI;
+		kbd->phys = info->phys;
-	kbd->id.vendor = 0x5853;
+		kbd->id.bustype = BUS_PCI;
-	kbd->id.product = 0xffff;
+		kbd->id.vendor = 0x5853;
+		kbd->id.product = 0xffff;
 
-	__set_bit(EV_KEY, kbd->evbit);
+		__set_bit(EV_KEY, kbd->evbit);
-	for (i = KEY_ESC; i < KEY_UNKNOWN; i++)
+		for (i = KEY_ESC; i < KEY_UNKNOWN; i++)
-		__set_bit(i, kbd->keybit);
+			__set_bit(i, kbd->keybit);
-	for (i = KEY_OK; i < KEY_MAX; i++)
+		for (i = KEY_OK; i < KEY_MAX; i++)
-		__set_bit(i, kbd->keybit);
+			__set_bit(i, kbd->keybit);
 
-	ret = input_register_device(kbd);
+		ret = input_register_device(kbd);
-	if (ret) {
+		if (ret) {
-		input_free_device(kbd);
+			input_free_device(kbd);
-		xenbus_dev_fatal(dev, ret, "input_register_device(kbd)");
+			xenbus_dev_fatal(dev, ret,
-		goto error;
+					 "input_register_device(kbd)");
+			goto error;
+		}
+		info->kbd = kbd;
 	}
-	info->kbd = kbd;
 
 	/* pointing device */
-	ptr = input_allocate_device();
+	if (with_ptr) {
-	if (!ptr)
+		unsigned int abs;
-		goto error_nomem;
-	ptr->name = "Xen Virtual Pointer";
-	ptr->phys = info->phys;
-	ptr->id.bustype = BUS_PCI;
-	ptr->id.vendor = 0x5853;
-	ptr->id.product = 0xfffe;
 
-	if (abs) {
+		/* Set input abs params to match backend screen res */
-		__set_bit(EV_ABS, ptr->evbit);
+		abs = xenbus_read_unsigned(dev->otherend,
-		input_set_abs_params(ptr, ABS_X, 0, ptr_size[KPARAM_X], 0, 0);
+					   XENKBD_FIELD_FEAT_ABS_POINTER, 0);
-		input_set_abs_params(ptr, ABS_Y, 0, ptr_size[KPARAM_Y], 0, 0);
+		ptr_size[KPARAM_X] = xenbus_read_unsigned(dev->otherend,
-	} else {
+							  XENKBD_FIELD_WIDTH,
-		input_set_capability(ptr, EV_REL, REL_X);
+							  ptr_size[KPARAM_X]);
-		input_set_capability(ptr, EV_REL, REL_Y);
+		ptr_size[KPARAM_Y] = xenbus_read_unsigned(dev->otherend,
+							  XENKBD_FIELD_HEIGHT,
+							  ptr_size[KPARAM_Y]);
+		if (abs) {
+			ret = xenbus_write(XBT_NIL, dev->nodename,
+					   XENKBD_FIELD_REQ_ABS_POINTER, "1");
+			if (ret) {
+				pr_warn("xenkbd: can't request abs-pointer\n");
+				abs = 0;
+			}
+		}
+
+		ptr = input_allocate_device();
+		if (!ptr)
+			goto error_nomem;
+		ptr->name = "Xen Virtual Pointer";
+		ptr->phys = info->phys;
+		ptr->id.bustype = BUS_PCI;
+		ptr->id.vendor = 0x5853;
+		ptr->id.product = 0xfffe;
+
+		if (abs) {
+			__set_bit(EV_ABS, ptr->evbit);
+			input_set_abs_params(ptr, ABS_X, 0,
+					     ptr_size[KPARAM_X], 0, 0);
+			input_set_abs_params(ptr, ABS_Y, 0,
+					     ptr_size[KPARAM_Y], 0, 0);
+		} else {
+			input_set_capability(ptr, EV_REL, REL_X);
+			input_set_capability(ptr, EV_REL, REL_Y);
+		}
+		input_set_capability(ptr, EV_REL, REL_WHEEL);
+
+		__set_bit(EV_KEY, ptr->evbit);
+		for (i = BTN_LEFT; i <= BTN_TASK; i++)
+			__set_bit(i, ptr->keybit);
+
+		ret = input_register_device(ptr);
+		if (ret) {
+			input_free_device(ptr);
+			xenbus_dev_fatal(dev, ret,
+					 "input_register_device(ptr)");
+			goto error;
+		}
+		info->ptr = ptr;
 	}
-	input_set_capability(ptr, EV_REL, REL_WHEEL);
-
-	__set_bit(EV_KEY, ptr->evbit);
-	for (i = BTN_LEFT; i <= BTN_TASK; i++)
-		__set_bit(i, ptr->keybit);
-
-	ret = input_register_device(ptr);
-	if (ret) {
-		input_free_device(ptr);
-		xenbus_dev_fatal(dev, ret, "input_register_device(ptr)");
-		goto error;
-	}
-	info->ptr = ptr;
 
 	/* multi-touch device */
-	if (touch) {
+	if (with_mtouch) {
 		int num_cont, width, height;
 
 		mtouch = input_allocate_device();
 		if (!mtouch)
 			goto error_nomem;
 
-		num_cont = xenbus_read_unsigned(info->xbdev->nodename,
+		num_cont = xenbus_read_unsigned(info->xbdev->otherend,
 						XENKBD_FIELD_MT_NUM_CONTACTS,
 						1);
-		width = xenbus_read_unsigned(info->xbdev->nodename,
+		width = xenbus_read_unsigned(info->xbdev->otherend,
 					     XENKBD_FIELD_MT_WIDTH,
 					     XENFB_WIDTH);
-		height = xenbus_read_unsigned(info->xbdev->nodename,
+		height = xenbus_read_unsigned(info->xbdev->otherend,
 					      XENKBD_FIELD_MT_HEIGHT,
 					      XENFB_HEIGHT);
 
@@ -346,6 +376,11 @@ static int xenkbd_probe(struct xenbus_device *dev,
 		info->mtouch = mtouch;
 	}
 
+	if (!(with_kbd || with_ptr || with_mtouch)) {
+		ret = -ENXIO;
+		goto error;
+	}
+
 	ret = xenkbd_connect_backend(dev, info);
 	if (ret < 0)
 		goto error;

drivers/input/misc/yealink.c

@@ -894,12 +894,12 @@ static int usb_probe(struct usb_interface *intf, const struct usb_device_id *id)
 
 	/* allocate usb buffers */
 	yld->irq_data = usb_alloc_coherent(udev, USB_PKT_LEN,
-					   GFP_ATOMIC, &yld->irq_dma);
+					   GFP_KERNEL, &yld->irq_dma);
 	if (yld->irq_data == NULL)
 		return usb_cleanup(yld, -ENOMEM);
 
 	yld->ctl_data = usb_alloc_coherent(udev, USB_PKT_LEN,
-					   GFP_ATOMIC, &yld->ctl_dma);
+					   GFP_KERNEL, &yld->ctl_dma);
 	if (!yld->ctl_data)
 		return usb_cleanup(yld, -ENOMEM);
 

drivers/input/mouse/appletouch.c

@@ -472,6 +472,7 @@ static int atp_status_check(struct urb *urb)
 				dev->info->datalen, dev->urb->actual_length);
 			dev->overflow_warned = true;
 		}
+		/* fall through */
 	case -ECONNRESET:
 	case -ENOENT:
 	case -ESHUTDOWN:
@@ -810,7 +811,7 @@ static int atp_open(struct input_dev *input)
 {
 	struct atp *dev = input_get_drvdata(input);
 
-	if (usb_submit_urb(dev->urb, GFP_ATOMIC))
+	if (usb_submit_urb(dev->urb, GFP_KERNEL))
 		return -EIO;
 
 	dev->open = true;
@@ -976,7 +977,7 @@ static int atp_recover(struct atp *dev)
 	if (error)
 		return error;
 
-	if (dev->open && usb_submit_urb(dev->urb, GFP_ATOMIC))
+	if (dev->open && usb_submit_urb(dev->urb, GFP_KERNEL))
 		return -EIO;
 
 	return 0;
@@ -994,7 +995,7 @@ static int atp_resume(struct usb_interface *iface)
 {
 	struct atp *dev = usb_get_intfdata(iface);
 
-	if (dev->open && usb_submit_urb(dev->urb, GFP_ATOMIC))
+	if (dev->open && usb_submit_urb(dev->urb, GFP_KERNEL))
 		return -EIO;
 
 	return 0;

drivers/input/mouse/cyapa_gen5.c

@@ -2554,6 +2554,7 @@ static int cyapa_gen5_do_operational_check(struct cyapa *cyapa)
 		}
 
 		cyapa->state = CYAPA_STATE_GEN5_APP;
+		/* fall through */
 
 	case CYAPA_STATE_GEN5_APP:
 		/*

drivers/input/mouse/cyapa_gen6.c

@@ -680,6 +680,7 @@ static int cyapa_gen6_operational_check(struct cyapa *cyapa)
 		}
 
 		cyapa->state = CYAPA_STATE_GEN6_APP;
+		/* fall through */
 
 	case CYAPA_STATE_GEN6_APP:
 		/*

drivers/input/mouse/elan_i2c_smbus.c

@@ -387,7 +387,7 @@ static int elan_smbus_prepare_fw_update(struct i2c_client *client)
 		len = i2c_smbus_read_block_data(client,
 						ETP_SMBUS_IAP_PASSWORD_READ,
 						val);
-		if (len < sizeof(u16)) {
+		if (len < (int)sizeof(u16)) {
 			error = len < 0 ? len : -EIO;
 			dev_err(dev, "failed to read iap password: %d\n",
 				error);

drivers/input/mouse/elantech.c

@@ -340,7 +340,7 @@ static void elantech_report_absolute_v2(struct psmouse *psmouse)
 		 */
 		if (packet[3] & 0x80)
 			fingers = 4;
-		/* pass through... */
+		/* fall through */
 	case 1:
 		/*
 		 * byte 1:  .   .   .   .  x11 x10 x9  x8

drivers/input/mouse/inport.c

@@ -26,10 +26,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/mouse/logibm.c

@@ -27,10 +27,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/mouse/pc110pad.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/mouse/sermouse.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>
@@ -143,7 +139,8 @@ static void sermouse_process_ms(struct sermouse *sermouse, signed char data)
 			switch (sermouse->type) {
 
 				case SERIO_MS:
-					 sermouse->type = SERIO_MP;
+					sermouse->type = SERIO_MP;
+					/* fall through */
 
 				case SERIO_MP:
 					if ((data >> 2) & 3) break;	/* M++ Wireless Extension packet. */
@@ -154,6 +151,7 @@ static void sermouse_process_ms(struct sermouse *sermouse, signed char data)
 				case SERIO_MZP:
 				case SERIO_MZPP:
 					input_report_key(dev, BTN_SIDE,   (data >> 5) & 1);
+					/* fall through */
 
 				case SERIO_MZ:
 					input_report_key(dev, BTN_MIDDLE, (data >> 4) & 1);

drivers/input/serio/ct82c710.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/delay.h>

drivers/input/serio/i8042.c

@@ -573,6 +573,9 @@ static irqreturn_t i8042_interrupt(int irq, void *dev_id)
 	port = &i8042_ports[port_no];
 	serio = port->exists ? port->serio : NULL;
 
+	if (irq && serio)
+		pm_wakeup_event(&serio->dev, 0);
+
 	filter_dbg(port->driver_bound, data, "<- i8042 (interrupt, %d, %d%s%s)\n",
 		   port_no, irq,
 		   dfl & SERIO_PARITY ? ", bad parity" : "",

drivers/input/serio/q40kbd.c

@@ -23,10 +23,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/serio/rpckbd.c

@@ -21,10 +21,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/module.h>

drivers/input/serio/serio.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

drivers/input/tablet/aiptek.c

@@ -1712,7 +1712,7 @@ aiptek_probe(struct usb_interface *intf, const struct usb_device_id *id)
         }
 
 	aiptek->data = usb_alloc_coherent(usbdev, AIPTEK_PACKET_LENGTH,
-					  GFP_ATOMIC, &aiptek->data_dma);
+					  GFP_KERNEL, &aiptek->data_dma);
         if (!aiptek->data) {
 		dev_warn(&intf->dev, "cannot allocate usb buffer\n");
 		goto fail1;

drivers/input/touchscreen/Kconfig

@@ -164,6 +164,18 @@ config TOUCHSCREEN_BU21013
 	  To compile this driver as a module, choose M here: the
 	  module will be called bu21013_ts.
 
+config TOUCHSCREEN_BU21029
+	tristate "Rohm BU21029 based touch panel controllers"
+	depends on I2C
+	help
+	  Say Y here if you have a Rohm BU21029 touchscreen controller
+	  connected to your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bu21029_ts.
+
 config TOUCHSCREEN_CHIPONE_ICN8318
 	tristate "chipone icn8318 touchscreen controller"
 	depends on GPIOLIB || COMPILE_TEST

drivers/input/touchscreen/Makefile

@@ -19,6 +19,7 @@ obj-$(CONFIG_TOUCHSCREEN_AR1021_I2C)	+= ar1021_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ATMEL_MXT)	+= atmel_mxt_ts.o
 obj-$(CONFIG_TOUCHSCREEN_AUO_PIXCIR)	+= auo-pixcir-ts.o
 obj-$(CONFIG_TOUCHSCREEN_BU21013)	+= bu21013_ts.o
+obj-$(CONFIG_TOUCHSCREEN_BU21029)	+= bu21029_ts.o
 obj-$(CONFIG_TOUCHSCREEN_CHIPONE_ICN8318)	+= chipone_icn8318.o
 obj-$(CONFIG_TOUCHSCREEN_CHIPONE_ICN8505)	+= chipone_icn8505.o
 obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110)	+= cy8ctmg110_ts.o

drivers/input/touchscreen/atmel_mxt_ts.c

@@ -75,6 +75,7 @@
 #define MXT_SPT_DIGITIZER_T43		43
 #define MXT_SPT_MESSAGECOUNT_T44	44
 #define MXT_SPT_CTECONFIG_T46		46
+#define MXT_SPT_DYNAMICCONFIGURATIONCONTAINER_T71 71
 #define MXT_TOUCH_MULTITOUCHSCREEN_T100 100
 
 /* MXT_GEN_MESSAGE_T5 object */
@@ -88,12 +89,12 @@
 #define MXT_COMMAND_DIAGNOSTIC	5
 
 /* Define for T6 status byte */
-#define MXT_T6_STATUS_RESET	(1 << 7)
+#define MXT_T6_STATUS_RESET	BIT(7)
-#define MXT_T6_STATUS_OFL	(1 << 6)
+#define MXT_T6_STATUS_OFL	BIT(6)
-#define MXT_T6_STATUS_SIGERR	(1 << 5)
+#define MXT_T6_STATUS_SIGERR	BIT(5)
-#define MXT_T6_STATUS_CAL	(1 << 4)
+#define MXT_T6_STATUS_CAL	BIT(4)
-#define MXT_T6_STATUS_CFGERR	(1 << 3)
+#define MXT_T6_STATUS_CFGERR	BIT(3)
-#define MXT_T6_STATUS_COMSERR	(1 << 2)
+#define MXT_T6_STATUS_COMSERR	BIT(2)
 
 /* MXT_GEN_POWER_T7 field */
 struct t7_config {
@@ -112,14 +113,14 @@ struct t7_config {
 #define MXT_T9_RANGE		18
 
 /* MXT_TOUCH_MULTI_T9 status */
-#define MXT_T9_UNGRIP		(1 << 0)
+#define MXT_T9_UNGRIP		BIT(0)
-#define MXT_T9_SUPPRESS		(1 << 1)
+#define MXT_T9_SUPPRESS		BIT(1)
-#define MXT_T9_AMP		(1 << 2)
+#define MXT_T9_AMP		BIT(2)
-#define MXT_T9_VECTOR		(1 << 3)
+#define MXT_T9_VECTOR		BIT(3)
-#define MXT_T9_MOVE		(1 << 4)
+#define MXT_T9_MOVE		BIT(4)
-#define MXT_T9_RELEASE		(1 << 5)
+#define MXT_T9_RELEASE		BIT(5)
-#define MXT_T9_PRESS		(1 << 6)
+#define MXT_T9_PRESS		BIT(6)
-#define MXT_T9_DETECT		(1 << 7)
+#define MXT_T9_DETECT		BIT(7)
 
 struct t9_range {
 	__le16 x;
@@ -127,9 +128,9 @@ struct t9_range {
 } __packed;
 
 /* MXT_TOUCH_MULTI_T9 orient */
-#define MXT_T9_ORIENT_SWITCH	(1 << 0)
+#define MXT_T9_ORIENT_SWITCH	BIT(0)
-#define MXT_T9_ORIENT_INVERTX	(1 << 1)
+#define MXT_T9_ORIENT_INVERTX	BIT(1)
-#define MXT_T9_ORIENT_INVERTY	(1 << 2)
+#define MXT_T9_ORIENT_INVERTY	BIT(2)
 
 /* MXT_SPT_COMMSCONFIG_T18 */
 #define MXT_COMMS_CTRL		0
@@ -214,7 +215,7 @@ enum t100_type {
 #define MXT_FRAME_CRC_PASS	0x04
 #define MXT_APP_CRC_FAIL	0x40	/* valid 7 8 bit only */
 #define MXT_BOOT_STATUS_MASK	0x3f
-#define MXT_BOOT_EXTENDED_ID	(1 << 5)
+#define MXT_BOOT_EXTENDED_ID	BIT(5)
 #define MXT_BOOT_ID_MASK	0x1f
 
 /* Touchscreen absolute values */
@@ -276,6 +277,19 @@ enum mxt_suspend_mode {
 	MXT_SUSPEND_T9_CTRL	= 1,
 };
 
+/* Config update context */
+struct mxt_cfg {
+	u8 *raw;
+	size_t raw_size;
+	off_t raw_pos;
+
+	u8 *mem;
+	size_t mem_size;
+	int start_ofs;
+
+	struct mxt_info info;
+};
+
 /* Each client has this additional data */
 struct mxt_data {
 	struct i2c_client *client;
@@ -317,6 +331,7 @@ struct mxt_data {
 	u8 T6_reportid;
 	u16 T6_address;
 	u16 T7_address;
+	u16 T71_address;
 	u8 T9_reportid_min;
 	u8 T9_reportid_max;
 	u8 T19_reportid;
@@ -382,6 +397,7 @@ static bool mxt_object_readable(unsigned int type)
 	case MXT_SPT_USERDATA_T38:
 	case MXT_SPT_DIGITIZER_T43:
 	case MXT_SPT_CTECONFIG_T46:
+	case MXT_SPT_DYNAMICCONFIGURATIONCONTAINER_T71:
 		return true;
 	default:
 		return false;
@@ -712,13 +728,13 @@ static void mxt_proc_t6_messages(struct mxt_data *data, u8 *msg)
 	u8 status = msg[1];
 	u32 crc = msg[2] | (msg[3] << 8) | (msg[4] << 16);
 
-	complete(&data->crc_completion);
-
 	if (crc != data->config_crc) {
 		data->config_crc = crc;
 		dev_dbg(dev, "T6 Config Checksum: 0x%06X\n", crc);
 	}
 
+	complete(&data->crc_completion);
+
 	/* Detect reset */
 	if (status & MXT_T6_STATUS_RESET)
 		complete(&data->reset_completion);
@@ -827,6 +843,10 @@ static void mxt_proc_t9_message(struct mxt_data *data, u8 *message)
 			mxt_input_sync(data);
 		}
 
+		/* if active, pressure must be non-zero */
+		if (!amplitude)
+			amplitude = MXT_PRESSURE_DEFAULT;
+
 		/* Touch active */
 		input_mt_report_slot_state(input_dev, MT_TOOL_FINGER, 1);
 		input_report_abs(input_dev, ABS_MT_POSITION_X, x);
@@ -1279,12 +1299,7 @@ static u32 mxt_calculate_crc(u8 *base, off_t start_off, off_t end_off)
 	return crc;
 }
 
-static int mxt_prepare_cfg_mem(struct mxt_data *data,
+static int mxt_prepare_cfg_mem(struct mxt_data *data, struct mxt_cfg *cfg)
-			       const struct firmware *cfg,
-			       unsigned int data_pos,
-			       unsigned int cfg_start_ofs,
-			       u8 *config_mem,
-			       size_t config_mem_size)
 {
 	struct device *dev = &data->client->dev;
 	struct mxt_object *object;
@@ -1295,9 +1310,9 @@ static int mxt_prepare_cfg_mem(struct mxt_data *data,
 	u16 reg;
 	u8 val;
 
-	while (data_pos < cfg->size) {
+	while (cfg->raw_pos < cfg->raw_size) {
 		/* Read type, instance, length */
-		ret = sscanf(cfg->data + data_pos, "%x %x %x%n",
+		ret = sscanf(cfg->raw + cfg->raw_pos, "%x %x %x%n",
 			     &type, &instance, &size, &offset);
 		if (ret == 0) {
 			/* EOF */
@@ -1306,20 +1321,20 @@ static int mxt_prepare_cfg_mem(struct mxt_data *data,
 			dev_err(dev, "Bad format: failed to parse object\n");
 			return -EINVAL;
 		}
-		data_pos += offset;
+		cfg->raw_pos += offset;
 
 		object = mxt_get_object(data, type);
 		if (!object) {
 			/* Skip object */
 			for (i = 0; i < size; i++) {
-				ret = sscanf(cfg->data + data_pos, "%hhx%n",
+				ret = sscanf(cfg->raw + cfg->raw_pos, "%hhx%n",
 					     &val, &offset);
 				if (ret != 1) {
 					dev_err(dev, "Bad format in T%d at %d\n",
 						type, i);
 					return -EINVAL;
 				}
-				data_pos += offset;
+				cfg->raw_pos += offset;
 			}
 			continue;
 		}
@@ -1354,7 +1369,7 @@ static int mxt_prepare_cfg_mem(struct mxt_data *data,
 		reg = object->start_address + mxt_obj_size(object) * instance;
 
 		for (i = 0; i < size; i++) {
-			ret = sscanf(cfg->data + data_pos, "%hhx%n",
+			ret = sscanf(cfg->raw + cfg->raw_pos, "%hhx%n",
 				     &val,
 				     &offset);
 			if (ret != 1) {
@@ -1362,15 +1377,15 @@ static int mxt_prepare_cfg_mem(struct mxt_data *data,
 					type, i);
 				return -EINVAL;
 			}
-			data_pos += offset;
+			cfg->raw_pos += offset;
 
 			if (i > mxt_obj_size(object))
 				continue;
 
-			byte_offset = reg + i - cfg_start_ofs;
+			byte_offset = reg + i - cfg->start_ofs;
 
-			if (byte_offset >= 0 && byte_offset < config_mem_size) {
+			if (byte_offset >= 0 && byte_offset < cfg->mem_size) {
-				*(config_mem + byte_offset) = val;
+				*(cfg->mem + byte_offset) = val;
 			} else {
 				dev_err(dev, "Bad object: reg:%d, T%d, ofs=%d\n",
 					reg, object->type, byte_offset);
@@ -1382,22 +1397,21 @@ static int mxt_prepare_cfg_mem(struct mxt_data *data,
 	return 0;
 }
 
-static int mxt_upload_cfg_mem(struct mxt_data *data, unsigned int cfg_start,
+static int mxt_upload_cfg_mem(struct mxt_data *data, struct mxt_cfg *cfg)
-			      u8 *config_mem, size_t config_mem_size)
 {
 	unsigned int byte_offset = 0;
 	int error;
 
 	/* Write configuration as blocks */
-	while (byte_offset < config_mem_size) {
+	while (byte_offset < cfg->mem_size) {
-		unsigned int size = config_mem_size - byte_offset;
+		unsigned int size = cfg->mem_size - byte_offset;
 
 		if (size > MXT_MAX_BLOCK_WRITE)
 			size = MXT_MAX_BLOCK_WRITE;
 
 		error = __mxt_write_reg(data->client,
-					cfg_start + byte_offset,
+					cfg->start_ofs + byte_offset,
-					size, config_mem + byte_offset);
+					size, cfg->mem + byte_offset);
 		if (error) {
 			dev_err(&data->client->dev,
 				"Config write error, ret=%d\n", error);
@@ -1431,65 +1445,75 @@ static int mxt_init_t7_power_cfg(struct mxt_data *data);
  *   <SIZE> - 2-byte object size as hex
  *   <CONTENTS> - array of <SIZE> 1-byte hex values
  */
-static int mxt_update_cfg(struct mxt_data *data, const struct firmware *cfg)
+static int mxt_update_cfg(struct mxt_data *data, const struct firmware *fw)
 {
 	struct device *dev = &data->client->dev;
-	struct mxt_info cfg_info;
+	struct mxt_cfg cfg;
 	int ret;
 	int offset;
-	int data_pos;
 	int i;
-	int cfg_start_ofs;
 	u32 info_crc, config_crc, calculated_crc;
-	u8 *config_mem;
+	u16 crc_start = 0;
-	size_t config_mem_size;
+
+	/* Make zero terminated copy of the OBP_RAW file */
+	cfg.raw = kmemdup_nul(fw->data, fw->size, GFP_KERNEL);
+	if (!cfg.raw)
+		return -ENOMEM;
+
+	cfg.raw_size = fw->size;
 
 	mxt_update_crc(data, MXT_COMMAND_REPORTALL, 1);
 
-	if (strncmp(cfg->data, MXT_CFG_MAGIC, strlen(MXT_CFG_MAGIC))) {
+	if (strncmp(cfg.raw, MXT_CFG_MAGIC, strlen(MXT_CFG_MAGIC))) {
 		dev_err(dev, "Unrecognised config file\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto release_raw;
 	}
 
-	data_pos = strlen(MXT_CFG_MAGIC);
+	cfg.raw_pos = strlen(MXT_CFG_MAGIC);
 
 	/* Load information block and check */
 	for (i = 0; i < sizeof(struct mxt_info); i++) {
-		ret = sscanf(cfg->data + data_pos, "%hhx%n",
+		ret = sscanf(cfg.raw + cfg.raw_pos, "%hhx%n",
-			     (unsigned char *)&cfg_info + i,
+			     (unsigned char *)&cfg.info + i,
 			     &offset);
 		if (ret != 1) {
 			dev_err(dev, "Bad format\n");
-			return -EINVAL;
+			ret = -EINVAL;
+			goto release_raw;
 		}
 
-		data_pos += offset;
+		cfg.raw_pos += offset;
 	}
 
-	if (cfg_info.family_id != data->info->family_id) {
+	if (cfg.info.family_id != data->info->family_id) {
 		dev_err(dev, "Family ID mismatch!\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto release_raw;
 	}
 
-	if (cfg_info.variant_id != data->info->variant_id) {
+	if (cfg.info.variant_id != data->info->variant_id) {
 		dev_err(dev, "Variant ID mismatch!\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto release_raw;
 	}
 
 	/* Read CRCs */
-	ret = sscanf(cfg->data + data_pos, "%x%n", &info_crc, &offset);
+	ret = sscanf(cfg.raw + cfg.raw_pos, "%x%n", &info_crc, &offset);
 	if (ret != 1) {
 		dev_err(dev, "Bad format: failed to parse Info CRC\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto release_raw;
 	}
-	data_pos += offset;
+	cfg.raw_pos += offset;
 
-	ret = sscanf(cfg->data + data_pos, "%x%n", &config_crc, &offset);
+	ret = sscanf(cfg.raw + cfg.raw_pos, "%x%n", &config_crc, &offset);
 	if (ret != 1) {
 		dev_err(dev, "Bad format: failed to parse Config CRC\n");
-		return -EINVAL;
+		ret = -EINVAL;
+		goto release_raw;
 	}
-	data_pos += offset;
+	cfg.raw_pos += offset;
 
 	/*
 	 * The Info Block CRC is calculated over mxt_info and the object
@@ -1515,39 +1539,39 @@ static int mxt_update_cfg(struct mxt_data *data, const struct firmware *cfg)
 	}
 
 	/* Malloc memory to store configuration */
-	cfg_start_ofs = MXT_OBJECT_START +
+	cfg.start_ofs = MXT_OBJECT_START +
 			data->info->object_num * sizeof(struct mxt_object) +
 			MXT_INFO_CHECKSUM_SIZE;
-	config_mem_size = data->mem_size - cfg_start_ofs;
+	cfg.mem_size = data->mem_size - cfg.start_ofs;
-	config_mem = kzalloc(config_mem_size, GFP_KERNEL);
+	cfg.mem = kzalloc(cfg.mem_size, GFP_KERNEL);
-	if (!config_mem) {
+	if (!cfg.mem) {
-		dev_err(dev, "Failed to allocate memory\n");
+		ret = -ENOMEM;
-		return -ENOMEM;
+		goto release_raw;
 	}
 
-	ret = mxt_prepare_cfg_mem(data, cfg, data_pos, cfg_start_ofs,
+	ret = mxt_prepare_cfg_mem(data, &cfg);
-				  config_mem, config_mem_size);
 	if (ret)
 		goto release_mem;
 
 	/* Calculate crc of the received configs (not the raw config file) */
-	if (data->T7_address < cfg_start_ofs) {
+	if (data->T71_address)
-		dev_err(dev, "Bad T7 address, T7addr = %x, config offset %x\n",
+		crc_start = data->T71_address;
-			data->T7_address, cfg_start_ofs);
+	else if (data->T7_address)
-		ret = 0;
+		crc_start = data->T7_address;
-		goto release_mem;
+	else
+		dev_warn(dev, "Could not find CRC start\n");
+
+	if (crc_start > cfg.start_ofs) {
+		calculated_crc = mxt_calculate_crc(cfg.mem,
+						   crc_start - cfg.start_ofs,
+						   cfg.mem_size);
+
+		if (config_crc > 0 && config_crc != calculated_crc)
+			dev_warn(dev, "Config CRC in file inconsistent, calculated=%06X, file=%06X\n",
+				 calculated_crc, config_crc);
 	}
 
-	calculated_crc = mxt_calculate_crc(config_mem,
+	ret = mxt_upload_cfg_mem(data, &cfg);
-					   data->T7_address - cfg_start_ofs,
-					   config_mem_size);
-
-	if (config_crc > 0 && config_crc != calculated_crc)
-		dev_warn(dev, "Config CRC error, calculated=%06X, file=%06X\n",
-			 calculated_crc, config_crc);
-
-	ret = mxt_upload_cfg_mem(data, cfg_start_ofs,
-				 config_mem, config_mem_size);
 	if (ret)
 		goto release_mem;
 
@@ -1562,8 +1586,10 @@ static int mxt_update_cfg(struct mxt_data *data, const struct firmware *cfg)
 	/* T7 config may have changed */
 	mxt_init_t7_power_cfg(data);
 
+release_raw:
+	kfree(cfg.raw);
 release_mem:
-	kfree(config_mem);
+	kfree(cfg.mem);
 	return ret;
 }
 
@@ -1591,6 +1617,7 @@ static void mxt_free_object_table(struct mxt_data *data)
 	data->T5_msg_size = 0;
 	data->T6_reportid = 0;
 	data->T7_address = 0;
+	data->T71_address = 0;
 	data->T9_reportid_min = 0;
 	data->T9_reportid_max = 0;
 	data->T19_reportid = 0;
@@ -1656,12 +1683,16 @@ static int mxt_parse_object_table(struct mxt_data *data,
 		case MXT_GEN_POWER_T7:
 			data->T7_address = object->start_address;
 			break;
+		case MXT_SPT_DYNAMICCONFIGURATIONCONTAINER_T71:
+			data->T71_address = object->start_address;
+			break;
 		case MXT_TOUCH_MULTI_T9:
 			data->multitouch = MXT_TOUCH_MULTI_T9;
+			/* Only handle messages from first T9 instance */
 			data->T9_reportid_min = min_id;
-			data->T9_reportid_max = max_id;
+			data->T9_reportid_max = min_id +
-			data->num_touchids = object->num_report_ids
+						object->num_report_ids - 1;
-						* mxt_obj_instances(object);
+			data->num_touchids = object->num_report_ids;
 			break;
 		case MXT_SPT_MESSAGECOUNT_T44:
 			data->T44_address = object->start_address;
@@ -1981,10 +2012,8 @@ static int mxt_initialize_input_device(struct mxt_data *data)
 
 	/* Register input device */
 	input_dev = input_allocate_device();
-	if (!input_dev) {
+	if (!input_dev)
-		dev_err(dev, "Failed to allocate memory\n");
 		return -ENOMEM;
-	}
 
 	input_dev->name = "Atmel maXTouch Touchscreen";
 	input_dev->phys = data->phys;
@@ -2054,12 +2083,6 @@ static int mxt_initialize_input_device(struct mxt_data *data)
 				     0, 255, 0, 0);
 	}
 
-	if (data->multitouch == MXT_TOUCH_MULTITOUCHSCREEN_T100 &&
-	    data->t100_aux_ampl) {
-		input_set_abs_params(input_dev, ABS_MT_PRESSURE,
-				     0, 255, 0, 0);
-	}
-
 	if (data->multitouch == MXT_TOUCH_MULTITOUCHSCREEN_T100 &&
 	    data->t100_aux_vect) {
 		input_set_abs_params(input_dev, ABS_MT_ORIENTATION,

drivers/input/touchscreen/bu21029_ts.c

@@ -0,0 +1,484 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rohm BU21029 touchscreen controller driver
+ *
+ * Copyright (C) 2015-2018 Bosch Sicherheitssysteme GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/touchscreen.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/regulator/consumer.h>
+#include <linux/timer.h>
+
+/*
+ * HW_ID1 Register (PAGE=0, ADDR=0x0E, Reset value=0x02, Read only)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |                                 HW_IDH                                |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * HW_ID2 Register (PAGE=0, ADDR=0x0F, Reset value=0x29, Read only)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |                                 HW_IDL                                |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * HW_IDH: high 8bits of IC's ID
+ * HW_IDL: low  8bits of IC's ID
+ */
+#define BU21029_HWID_REG	(0x0E << 3)
+#define SUPPORTED_HWID		0x0229
+
+/*
+ * CFR0 Register (PAGE=0, ADDR=0x00, Reset value=0x20)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   0    |   0    |  CALIB |  INTRM |   0    |   0    |   0    |   0    |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * CALIB: 0 = not to use calibration result (*)
+ *        1 = use calibration result
+ * INTRM: 0 = INT output depend on "pen down" (*)
+ *        1 = INT output always "0"
+ */
+#define BU21029_CFR0_REG	(0x00 << 3)
+#define CFR0_VALUE		0x00
+
+/*
+ * CFR1 Register (PAGE=0, ADDR=0x01, Reset value=0xA6)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |  MAV   |         AVE[2:0]         |   0    |         SMPL[2:0]        |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * MAV:  0 = median average filter off
+ *       1 = median average filter on (*)
+ * AVE:  AVE+1 = number of average samples for MAV,
+ *               if AVE>SMPL, then AVE=SMPL (=3)
+ * SMPL: SMPL+1 = number of conversion samples for MAV (=7)
+ */
+#define BU21029_CFR1_REG	(0x01 << 3)
+#define CFR1_VALUE		0xA6
+
+/*
+ * CFR2 Register (PAGE=0, ADDR=0x02, Reset value=0x04)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |          INTVL_TIME[3:0]          |          TIME_ST_ADC[3:0]         |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * INTVL_TIME: waiting time between completion of conversion
+ *             and start of next conversion, only usable in
+ *             autoscan mode (=20.480ms)
+ * TIME_ST_ADC: waiting time between application of voltage
+ *              to panel and start of A/D conversion (=100us)
+ */
+#define BU21029_CFR2_REG	(0x02 << 3)
+#define CFR2_VALUE		0xC9
+
+/*
+ * CFR3 Register (PAGE=0, ADDR=0x0B, Reset value=0x72)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |  RM8   | STRETCH|  PU90K |  DUAL  |           PIDAC_OFS[3:0]          |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * RM8: 0 = coordinate resolution is 12bit (*)
+ *      1 = coordinate resolution is 8bit
+ * STRETCH: 0 = SCL_STRETCH function off
+ *          1 = SCL_STRETCH function on (*)
+ * PU90K: 0 = internal pull-up resistance for touch detection is ~50kohms (*)
+ *        1 = internal pull-up resistance for touch detection is ~90kohms
+ * DUAL: 0 = dual touch detection off (*)
+ *       1 = dual touch detection on
+ * PIDAC_OFS: dual touch detection circuit adjustment, it is not necessary
+ *            to change this from initial value
+ */
+#define BU21029_CFR3_REG	(0x0B << 3)
+#define CFR3_VALUE		0x42
+
+/*
+ * LDO Register (PAGE=0, ADDR=0x0C, Reset value=0x00)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   0    |         PVDD[2:0]        |   0    |         AVDD[2:0]        |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * PVDD: output voltage of panel output regulator (=2.000V)
+ * AVDD: output voltage of analog circuit regulator (=2.000V)
+ */
+#define BU21029_LDO_REG		(0x0C << 3)
+#define LDO_VALUE		0x77
+
+/*
+ * Serial Interface Command Byte 1 (CID=1)
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   D7   |   D6   |   D5   |   D4   |   D3   |   D2   |   D1   |   D0   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * |   1    |                 CF                |  CMSK  |  PDM   |  STP   |
+ * +--------+--------+--------+--------+--------+--------+--------+--------+
+ * CF: conversion function, see table 3 in datasheet p6 (=0000, automatic scan)
+ * CMSK: 0 = executes convert function (*)
+ *       1 = reads the convert result
+ * PDM: 0 = power down after convert function stops (*)
+ *      1 = keep power on after convert function stops
+ * STP: 1 = abort current conversion and power down, set to "0" automatically
+ */
+#define BU21029_AUTOSCAN	0x80
+
+/*
+ * The timeout value needs to be larger than INTVL_TIME + tConv4 (sample and
+ * conversion time), where tConv4 is calculated by formula:
+ * tPON + tDLY1 + (tTIME_ST_ADC + (tADC * tSMPL) * 2 + tDLY2) * 3
+ * see figure 8 in datasheet p15 for details of each field.
+ */
+#define PEN_UP_TIMEOUT_MS	50
+
+#define STOP_DELAY_MIN_US	50
+#define STOP_DELAY_MAX_US	1000
+#define START_DELAY_MS		2
+#define BUF_LEN			8
+#define SCALE_12BIT		(1 << 12)
+#define MAX_12BIT		((1 << 12) - 1)
+#define DRIVER_NAME		"bu21029"
+
+struct bu21029_ts_data {
+	struct i2c_client		*client;
+	struct input_dev		*in_dev;
+	struct timer_list		timer;
+	struct regulator		*vdd;
+	struct gpio_desc		*reset_gpios;
+	u32				x_plate_ohms;
+	struct touchscreen_properties	prop;
+};
+
+static void bu21029_touch_report(struct bu21029_ts_data *bu21029, const u8 *buf)
+{
+	u16 x, y, z1, z2;
+	u32 rz;
+	s32 max_pressure = input_abs_get_max(bu21029->in_dev, ABS_PRESSURE);
+
+	/*
+	 * compose upper 8 and lower 4 bits into a 12bit value:
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 * |            ByteH              |            ByteL              |
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 * |b07|b06|b05|b04|b03|b02|b01|b00|b07|b06|b05|b04|b03|b02|b01|b00|
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 * |v11|v10|v09|v08|v07|v06|v05|v04|v03|v02|v01|v00| 0 | 0 | 0 | 0 |
+	 * +---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
+	 */
+	x  = (buf[0] << 4) | (buf[1] >> 4);
+	y  = (buf[2] << 4) | (buf[3] >> 4);
+	z1 = (buf[4] << 4) | (buf[5] >> 4);
+	z2 = (buf[6] << 4) | (buf[7] >> 4);
+
+	if (z1 && z2) {
+		/*
+		 * calculate Rz (pressure resistance value) by equation:
+		 * Rz = Rx * (x/Q) * ((z2/z1) - 1), where
+		 * Rx is x-plate resistance,
+		 * Q  is the touch screen resolution (8bit = 256, 12bit = 4096)
+		 * x, z1, z2 are the measured positions.
+		 */
+		rz  = z2 - z1;
+		rz *= x;
+		rz *= bu21029->x_plate_ohms;
+		rz /= z1;
+		rz  = DIV_ROUND_CLOSEST(rz, SCALE_12BIT);
+		if (rz <= max_pressure) {
+			touchscreen_report_pos(bu21029->in_dev, &bu21029->prop,
+					       x, y, false);
+			input_report_abs(bu21029->in_dev, ABS_PRESSURE,
+					 max_pressure - rz);
+			input_report_key(bu21029->in_dev, BTN_TOUCH, 1);
+			input_sync(bu21029->in_dev);
+		}
+	}
+}
+
+static void bu21029_touch_release(struct timer_list *t)
+{
+	struct bu21029_ts_data *bu21029 = from_timer(bu21029, t, timer);
+
+	input_report_abs(bu21029->in_dev, ABS_PRESSURE, 0);
+	input_report_key(bu21029->in_dev, BTN_TOUCH, 0);
+	input_sync(bu21029->in_dev);
+}
+
+static irqreturn_t bu21029_touch_soft_irq(int irq, void *data)
+{
+	struct bu21029_ts_data *bu21029 = data;
+	u8 buf[BUF_LEN];
+	int error;
+
+	/*
+	 * Read touch data and deassert interrupt (will assert again after
+	 * INTVL_TIME + tConv4 for continuous touch)
+	 */
+	error = i2c_smbus_read_i2c_block_data(bu21029->client, BU21029_AUTOSCAN,
+					      sizeof(buf), buf);
+	if (error < 0)
+		goto out;
+
+	bu21029_touch_report(bu21029, buf);
+
+	/* reset timer for pen up detection */
+	mod_timer(&bu21029->timer,
+		  jiffies + msecs_to_jiffies(PEN_UP_TIMEOUT_MS));
+
+out:
+	return IRQ_HANDLED;
+}
+
+static void bu21029_put_chip_in_reset(struct bu21029_ts_data *bu21029)
+{
+	if (bu21029->reset_gpios) {
+		gpiod_set_value_cansleep(bu21029->reset_gpios, 1);
+		usleep_range(STOP_DELAY_MIN_US, STOP_DELAY_MAX_US);
+	}
+}
+
+static int bu21029_start_chip(struct input_dev *dev)
+{
+	struct bu21029_ts_data *bu21029 = input_get_drvdata(dev);
+	struct i2c_client *i2c = bu21029->client;
+	struct {
+		u8 reg;
+		u8 value;
+	} init_table[] = {
+		{BU21029_CFR0_REG, CFR0_VALUE},
+		{BU21029_CFR1_REG, CFR1_VALUE},
+		{BU21029_CFR2_REG, CFR2_VALUE},
+		{BU21029_CFR3_REG, CFR3_VALUE},
+		{BU21029_LDO_REG,  LDO_VALUE}
+	};
+	int error, i;
+	__be16 hwid;
+
+	error = regulator_enable(bu21029->vdd);
+	if (error) {
+		dev_err(&i2c->dev, "failed to power up chip: %d", error);
+		return error;
+	}
+
+	/* take chip out of reset */
+	if (bu21029->reset_gpios) {
+		gpiod_set_value_cansleep(bu21029->reset_gpios, 0);
+		msleep(START_DELAY_MS);
+	}
+
+	error = i2c_smbus_read_i2c_block_data(i2c, BU21029_HWID_REG,
+					      sizeof(hwid), (u8 *)&hwid);
+	if (error < 0) {
+		dev_err(&i2c->dev, "failed to read HW ID\n");
+		goto err_out;
+	}
+
+	if (be16_to_cpu(hwid) != SUPPORTED_HWID) {
+		dev_err(&i2c->dev,
+			"unsupported HW ID 0x%x\n", be16_to_cpu(hwid));
+		error = -ENODEV;
+		goto err_out;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(init_table); ++i) {
+		error = i2c_smbus_write_byte_data(i2c,
+						  init_table[i].reg,
+						  init_table[i].value);
+		if (error < 0) {
+			dev_err(&i2c->dev,
+				"failed to write %#02x to register %#02x: %d\n",
+				init_table[i].value, init_table[i].reg,
+				error);
+			goto err_out;
+		}
+	}
+
+	error = i2c_smbus_write_byte(i2c, BU21029_AUTOSCAN);
+	if (error < 0) {
+		dev_err(&i2c->dev, "failed to start autoscan\n");
+		goto err_out;
+	}
+
+	enable_irq(bu21029->client->irq);
+	return 0;
+
+err_out:
+	bu21029_put_chip_in_reset(bu21029);
+	regulator_disable(bu21029->vdd);
+	return error;
+}
+
+static void bu21029_stop_chip(struct input_dev *dev)
+{
+	struct bu21029_ts_data *bu21029 = input_get_drvdata(dev);
+
+	disable_irq(bu21029->client->irq);
+	del_timer_sync(&bu21029->timer);
+
+	bu21029_put_chip_in_reset(bu21029);
+	regulator_disable(bu21029->vdd);
+}
+
+static int bu21029_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct bu21029_ts_data *bu21029;
+	struct input_dev *in_dev;
+	int error;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_WRITE_BYTE |
+				     I2C_FUNC_SMBUS_WRITE_BYTE_DATA |
+				     I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
+		dev_err(&client->dev,
+			"i2c functionality support is not sufficient\n");
+		return -EIO;
+	}
+
+	bu21029 = devm_kzalloc(&client->dev, sizeof(*bu21029), GFP_KERNEL);
+	if (!bu21029)
+		return -ENOMEM;
+
+	error = device_property_read_u32(&client->dev, "rohm,x-plate-ohms",
+					 &bu21029->x_plate_ohms);
+	if (error) {
+		dev_err(&client->dev,
+			"invalid 'x-plate-ohms' supplied: %d\n", error);
+		return error;
+	}
+
+	bu21029->vdd = devm_regulator_get(&client->dev, "vdd");
+	if (IS_ERR(bu21029->vdd)) {
+		error = PTR_ERR(bu21029->vdd);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"failed to acquire 'vdd' supply: %d\n", error);
+		return error;
+	}
+
+	bu21029->reset_gpios = devm_gpiod_get_optional(&client->dev,
+						       "reset", GPIOD_OUT_HIGH);
+	if (IS_ERR(bu21029->reset_gpios)) {
+		error = PTR_ERR(bu21029->reset_gpios);
+		if (error != -EPROBE_DEFER)
+			dev_err(&client->dev,
+				"failed to acquire 'reset' gpio: %d\n", error);
+		return error;
+	}
+
+	in_dev = devm_input_allocate_device(&client->dev);
+	if (!in_dev) {
+		dev_err(&client->dev, "unable to allocate input device\n");
+		return -ENOMEM;
+	}
+
+	bu21029->client = client;
+	bu21029->in_dev = in_dev;
+	timer_setup(&bu21029->timer, bu21029_touch_release, 0);
+
+	in_dev->name		= DRIVER_NAME;
+	in_dev->id.bustype	= BUS_I2C;
+	in_dev->open		= bu21029_start_chip;
+	in_dev->close		= bu21029_stop_chip;
+
+	input_set_capability(in_dev, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(in_dev, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(in_dev, ABS_Y, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(in_dev, ABS_PRESSURE, 0, MAX_12BIT, 0, 0);
+	touchscreen_parse_properties(in_dev, false, &bu21029->prop);
+
+	input_set_drvdata(in_dev, bu21029);
+
+	irq_set_status_flags(client->irq, IRQ_NOAUTOEN);
+	error = devm_request_threaded_irq(&client->dev, client->irq,
+					  NULL, bu21029_touch_soft_irq,
+					  IRQF_ONESHOT, DRIVER_NAME, bu21029);
+	if (error) {
+		dev_err(&client->dev,
+			"unable to request touch irq: %d\n", error);
+		return error;
+	}
+
+	error = input_register_device(in_dev);
+	if (error) {
+		dev_err(&client->dev,
+			"unable to register input device: %d\n", error);
+		return error;
+	}
+
+	i2c_set_clientdata(client, bu21029);
+
+	return 0;
+}
+
+static int __maybe_unused bu21029_suspend(struct device *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct bu21029_ts_data *bu21029 = i2c_get_clientdata(i2c);
+
+	if (!device_may_wakeup(dev)) {
+		mutex_lock(&bu21029->in_dev->mutex);
+		if (bu21029->in_dev->users)
+			bu21029_stop_chip(bu21029->in_dev);
+		mutex_unlock(&bu21029->in_dev->mutex);
+	}
+
+	return 0;
+}
+
+static int __maybe_unused bu21029_resume(struct device *dev)
+{
+	struct i2c_client *i2c = to_i2c_client(dev);
+	struct bu21029_ts_data *bu21029 = i2c_get_clientdata(i2c);
+
+	if (!device_may_wakeup(dev)) {
+		mutex_lock(&bu21029->in_dev->mutex);
+		if (bu21029->in_dev->users)
+			bu21029_start_chip(bu21029->in_dev);
+		mutex_unlock(&bu21029->in_dev->mutex);
+	}
+
+	return 0;
+}
+static SIMPLE_DEV_PM_OPS(bu21029_pm_ops, bu21029_suspend, bu21029_resume);
+
+static const struct i2c_device_id bu21029_ids[] = {
+	{ DRIVER_NAME, 0 },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, bu21029_ids);
+
+#ifdef CONFIG_OF
+static const struct of_device_id bu21029_of_ids[] = {
+	{ .compatible = "rohm,bu21029" },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, bu21029_of_ids);
+#endif
+
+static struct i2c_driver bu21029_driver = {
+	.driver	= {
+		.name		= DRIVER_NAME,
+		.of_match_table	= of_match_ptr(bu21029_of_ids),
+		.pm		= &bu21029_pm_ops,
+	},
+	.id_table	= bu21029_ids,
+	.probe		= bu21029_probe,
+};
+module_i2c_driver(bu21029_driver);
+
+MODULE_AUTHOR("Zhu Yi <yi.zhu5@cn.bosch.com>");
+MODULE_DESCRIPTION("Rohm BU21029 touchscreen controller driver");
+MODULE_LICENSE("GPL v2");

drivers/input/touchscreen/eeti_ts.c

@@ -1,9 +1,9 @@
 /*
  * Touch Screen driver for EETI's I2C connected touch screen panels
- *   Copyright (c) 2009 Daniel Mack <daniel@caiaq.de>
+ *   Copyright (c) 2009,2018 Daniel Mack <daniel@zonque.org>
  *
  * See EETI's software guide for the protocol specification:
- *   http://home.eeti.com.tw/web20/eg/guide.htm
+ *   http://home.eeti.com.tw/documentation.html
  *
  * Based on migor_ts.c
  *   Copyright (c) 2008 Magnus Damm
@@ -25,28 +25,22 @@
  */
 
 #include <linux/module.h>
-#include <linux/moduleparam.h>
 #include <linux/kernel.h>
 #include <linux/input.h>
+#include <linux/input/touchscreen.h>
 #include <linux/interrupt.h>
 #include <linux/i2c.h>
 #include <linux/timer.h>
 #include <linux/gpio/consumer.h>
+#include <linux/of.h>
 #include <linux/slab.h>
 #include <asm/unaligned.h>
 
-static bool flip_x;
-module_param(flip_x, bool, 0644);
-MODULE_PARM_DESC(flip_x, "flip x coordinate");
-
-static bool flip_y;
-module_param(flip_y, bool, 0644);
-MODULE_PARM_DESC(flip_y, "flip y coordinate");
-
 struct eeti_ts {
 	struct i2c_client *client;
 	struct input_dev *input;
 	struct gpio_desc *attn_gpio;
+	struct touchscreen_properties props;
 	bool running;
 };
 
@@ -73,17 +67,10 @@ static void eeti_ts_report_event(struct eeti_ts *eeti, u8 *buf)
 	x >>= res - EETI_TS_BITDEPTH;
 	y >>= res - EETI_TS_BITDEPTH;
 
-	if (flip_x)
-		x = EETI_MAXVAL - x;
-
-	if (flip_y)
-		y = EETI_MAXVAL - y;
-
 	if (buf[0] & REPORT_BIT_HAS_PRESSURE)
 		input_report_abs(eeti->input, ABS_PRESSURE, buf[5]);
 
-	input_report_abs(eeti->input, ABS_X, x);
+	touchscreen_report_pos(eeti->input, &eeti->props, x, y, false);
-	input_report_abs(eeti->input, ABS_Y, y);
 	input_report_key(eeti->input, BTN_TOUCH, buf[0] & REPORT_BIT_PRESSED);
 	input_sync(eeti->input);
 }
@@ -178,6 +165,8 @@ static int eeti_ts_probe(struct i2c_client *client,
 	input_set_abs_params(input, ABS_Y, 0, EETI_MAXVAL, 0, 0);
 	input_set_abs_params(input, ABS_PRESSURE, 0, 0xff, 0, 0);
 
+	touchscreen_parse_properties(input, false, &eeti->props);
+
 	input->name = client->name;
 	input->id.bustype = BUS_I2C;
 	input->open = eeti_ts_open;
@@ -262,10 +251,18 @@ static const struct i2c_device_id eeti_ts_id[] = {
 };
 MODULE_DEVICE_TABLE(i2c, eeti_ts_id);
 
+#ifdef CONFIG_OF
+static const struct of_device_id of_eeti_ts_match[] = {
+	{ .compatible = "eeti,exc3000-i2c", },
+	{ }
+};
+#endif
+
 static struct i2c_driver eeti_ts_driver = {
 	.driver = {
 		.name = "eeti_ts",
 		.pm = &eeti_ts_pm,
+		.of_match_table = of_match_ptr(of_eeti_ts_match),
 	},
 	.probe = eeti_ts_probe,
 	.id_table = eeti_ts_id,
@@ -274,5 +271,5 @@ static struct i2c_driver eeti_ts_driver = {
 module_i2c_driver(eeti_ts_driver);
 
 MODULE_DESCRIPTION("EETI Touchscreen driver");
-MODULE_AUTHOR("Daniel Mack <daniel@caiaq.de>");
+MODULE_AUTHOR("Daniel Mack <daniel@zonque.org>");
 MODULE_LICENSE("GPL");

drivers/input/touchscreen/egalax_ts.c

@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * Driver for EETI eGalax Multiple Touch Controller
  *
  * Copyright (C) 2011 Freescale Semiconductor, Inc.
  *
  * based on max11801_ts.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 /* EETI eGalax serial touch screen controller is a I2C based multiple

drivers/input/touchscreen/elo.c

@@ -352,6 +352,7 @@ static int elo_connect(struct serio *serio, struct serio_driver *drv)
 
 	case 1: /* 6-byte protocol */
 		input_set_abs_params(input_dev, ABS_PRESSURE, 0, 15, 0, 0);
+		/* fall through */
 
 	case 2: /* 4-byte protocol */
 		input_set_abs_params(input_dev, ABS_X, 96, 4000, 0, 0);

drivers/input/touchscreen/fsl-imx25-tcq.c

@@ -1,16 +1,11 @@
-/*
+// SPDX-License-Identifier: GPL-2.0
- * Copyright (C) 2014-2015 Pengutronix, Markus Pargmann <mpa@pengutronix.de>
+//
- *
+// Copyright (C) 2014-2015 Pengutronix, Markus Pargmann <mpa@pengutronix.de>
- * This program is free software; you can redistribute it and/or modify it under
+// Based on driver from 2011:
- * the terms of the GNU General Public License version 2 as published by the
+//   Juergen Beisert, Pengutronix <kernel@pengutronix.de>
- * Free Software Foundation.
+//
- *
+// This is the driver for the imx25 TCQ (Touchscreen Conversion Queue)
- * Based on driver from 2011:
+// connected to the imx25 ADC.
- *   Juergen Beisert, Pengutronix <kernel@pengutronix.de>
- *
- * This is the driver for the imx25 TCQ (Touchscreen Conversion Queue)
- * connected to the imx25 ADC.
- */
 
 #include <linux/clk.h>
 #include <linux/device.h>

drivers/input/touchscreen/gunze.c

@@ -20,10 +20,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@ucw.cz>, or by paper mail:
- * Vojtech Pavlik, Simunkova 1594, Prague 8, 182 00 Czech Republic
  */
 
 #include <linux/errno.h>

drivers/input/touchscreen/imx6ul_tsc.c

@@ -1,12 +1,8 @@
-/*
+// SPDX-License-Identifier: GPL-2.0
- * Freescale i.MX6UL touchscreen controller driver
+//
- *
+// Freescale i.MX6UL touchscreen controller driver
- * Copyright (C) 2015 Freescale Semiconductor, Inc.
+//
- *
+// Copyright (C) 2015 Freescale Semiconductor, Inc.
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
 
 #include <linux/errno.h>
 #include <linux/kernel.h>

drivers/input/touchscreen/raydium_i2c_ts.c

@@ -466,7 +466,7 @@ static bool raydium_i2c_boot_trigger(struct i2c_client *client)
 		}
 	}
 
-	return 0;
+	return false;
 }
 
 static bool raydium_i2c_fw_trigger(struct i2c_client *client)
@@ -492,7 +492,7 @@ static bool raydium_i2c_fw_trigger(struct i2c_client *client)
 		}
 	}
 
-	return 0;
+	return false;
 }
 
 static int raydium_i2c_check_path(struct i2c_client *client)

drivers/input/touchscreen/wdt87xx_i2c.c

@@ -1142,7 +1142,7 @@ static int __maybe_unused wdt87xx_resume(struct device *dev)
 	 * The chip may have been reset while system is resuming,
 	 * give it some time to settle.
 	 */
-	mdelay(100);
+	msleep(100);
 
 	error = wdt87xx_send_command(client, VND_CMD_START, 0);
 	if (error)

drivers/md/dm-raid.c

@@ -3859,7 +3859,7 @@ static int __load_dirty_region_bitmap(struct raid_set *rs)
 	/* Try loading the bitmap unless "raid0", which does not have one */
 	if (!rs_is_raid0(rs) &&
 	    !test_and_set_bit(RT_FLAG_RS_BITMAP_LOADED, &rs->runtime_flags)) {
-		r = bitmap_load(&rs->md);
+		r = md_bitmap_load(&rs->md);
 		if (r)
 			DMERR("Failed to load bitmap");
 	}
@@ -3987,8 +3987,8 @@ static int raid_preresume(struct dm_target *ti)
 	/* Resize bitmap to adjust to changed region size (aka MD bitmap chunksize) */
 	if (test_bit(RT_FLAG_RS_BITMAP_LOADED, &rs->runtime_flags) && mddev->bitmap &&
 	    mddev->bitmap_info.chunksize != to_bytes(rs->requested_bitmap_chunk_sectors)) {
-		r = bitmap_resize(mddev->bitmap, mddev->dev_sectors,
+		r = md_bitmap_resize(mddev->bitmap, mddev->dev_sectors,
-				  to_bytes(rs->requested_bitmap_chunk_sectors), 0);
+				     to_bytes(rs->requested_bitmap_chunk_sectors), 0);
 		if (r)
 			DMERR("Failed to resize bitmap");
 	}

drivers/md/md-bitmap.c

@@ -46,8 +46,8 @@ static inline char *bmname(struct bitmap *bitmap)
  * if we find our page, we increment the page's refcount so that it stays
  * allocated while we're using it
  */
-static int bitmap_checkpage(struct bitmap_counts *bitmap,
+static int md_bitmap_checkpage(struct bitmap_counts *bitmap,
-			    unsigned long page, int create, int no_hijack)
+			       unsigned long page, int create, int no_hijack)
 __releases(bitmap->lock)
 __acquires(bitmap->lock)
 {
@@ -115,7 +115,7 @@ __acquires(bitmap->lock)
 /* if page is completely empty, put it back on the free list, or dealloc it */
 /* if page was hijacked, unmark the flag so it might get alloced next time */
 /* Note: lock should be held when calling this */
-static void bitmap_checkfree(struct bitmap_counts *bitmap, unsigned long page)
+static void md_bitmap_checkfree(struct bitmap_counts *bitmap, unsigned long page)
 {
 	char *ptr;
 
@@ -280,7 +280,7 @@ restart:
 	return -EINVAL;
 }
 
-static void bitmap_file_kick(struct bitmap *bitmap);
+static void md_bitmap_file_kick(struct bitmap *bitmap);
 /*
  * write out a page to a file
  */
@@ -310,7 +310,7 @@ static void write_page(struct bitmap *bitmap, struct page *page, int wait)
 				   atomic_read(&bitmap->pending_writes)==0);
 	}
 	if (test_bit(BITMAP_WRITE_ERROR, &bitmap->flags))
-		bitmap_file_kick(bitmap);
+		md_bitmap_file_kick(bitmap);
 }
 
 static void end_bitmap_write(struct buffer_head *bh, int uptodate)
@@ -421,11 +421,11 @@ out:
  */
 
 /*
- * bitmap_wait_writes() should be called before writing any bitmap
+ * md_bitmap_wait_writes() should be called before writing any bitmap
  * blocks, to ensure previous writes, particularly from
- * bitmap_daemon_work(), have completed.
+ * md_bitmap_daemon_work(), have completed.
  */
-static void bitmap_wait_writes(struct bitmap *bitmap)
+static void md_bitmap_wait_writes(struct bitmap *bitmap)
 {
 	if (bitmap->storage.file)
 		wait_event(bitmap->write_wait,
@@ -443,7 +443,7 @@ static void bitmap_wait_writes(struct bitmap *bitmap)
 
 
 /* update the event counter and sync the superblock to disk */
-void bitmap_update_sb(struct bitmap *bitmap)
+void md_bitmap_update_sb(struct bitmap *bitmap)
 {
 	bitmap_super_t *sb;
 
@@ -476,10 +476,10 @@ void bitmap_update_sb(struct bitmap *bitmap)
 	kunmap_atomic(sb);
 	write_page(bitmap, bitmap->storage.sb_page, 1);
 }
-EXPORT_SYMBOL(bitmap_update_sb);
+EXPORT_SYMBOL(md_bitmap_update_sb);
 
 /* print out the bitmap file superblock */
-void bitmap_print_sb(struct bitmap *bitmap)
+void md_bitmap_print_sb(struct bitmap *bitmap)
 {
 	bitmap_super_t *sb;
 
@@ -518,7 +518,7 @@ void bitmap_print_sb(struct bitmap *bitmap)
  *
  * Returns: 0 on success, -Exxx on error
  */
-static int bitmap_new_disk_sb(struct bitmap *bitmap)
+static int md_bitmap_new_disk_sb(struct bitmap *bitmap)
 {
 	bitmap_super_t *sb;
 	unsigned long chunksize, daemon_sleep, write_behind;
@@ -577,7 +577,7 @@ static int bitmap_new_disk_sb(struct bitmap *bitmap)
 }
 
 /* read the superblock from the bitmap file and initialize some bitmap fields */
-static int bitmap_read_sb(struct bitmap *bitmap)
+static int md_bitmap_read_sb(struct bitmap *bitmap)
 {
 	char *reason = NULL;
 	bitmap_super_t *sb;
@@ -727,7 +727,7 @@ out_no_sb:
 	    bitmap->mddev->bitmap_info.space > sectors_reserved)
 		bitmap->mddev->bitmap_info.space = sectors_reserved;
 	if (err) {
-		bitmap_print_sb(bitmap);
+		md_bitmap_print_sb(bitmap);
 		if (bitmap->cluster_slot < 0)
 			md_cluster_stop(bitmap->mddev);
 	}
@@ -774,9 +774,9 @@ static inline struct page *filemap_get_page(struct bitmap_storage *store,
 	return store->filemap[file_page_index(store, chunk)];
 }
 
-static int bitmap_storage_alloc(struct bitmap_storage *store,
+static int md_bitmap_storage_alloc(struct bitmap_storage *store,
-				unsigned long chunks, int with_super,
+				   unsigned long chunks, int with_super,
-				int slot_number)
+				   int slot_number)
 {
 	int pnum, offset = 0;
 	unsigned long num_pages;
@@ -830,7 +830,7 @@ static int bitmap_storage_alloc(struct bitmap_storage *store,
 	return 0;
 }
 
-static void bitmap_file_unmap(struct bitmap_storage *store)
+static void md_bitmap_file_unmap(struct bitmap_storage *store)
 {
 	struct page **map, *sb_page;
 	int pages;
@@ -862,12 +862,12 @@ static void bitmap_file_unmap(struct bitmap_storage *store)
  * then it is no longer reliable, so we stop using it and we mark the file
  * as failed in the superblock
  */
-static void bitmap_file_kick(struct bitmap *bitmap)
+static void md_bitmap_file_kick(struct bitmap *bitmap)
 {
 	char *path, *ptr = NULL;
 
 	if (!test_and_set_bit(BITMAP_STALE, &bitmap->flags)) {
-		bitmap_update_sb(bitmap);
+		md_bitmap_update_sb(bitmap);
 
 		if (bitmap->storage.file) {
 			path = kmalloc(PAGE_SIZE, GFP_KERNEL);
@@ -923,7 +923,7 @@ static inline int test_and_clear_page_attr(struct bitmap *bitmap, int pnum,
  * we set the bit immediately, then we record the page number so that
  * when an unplug occurs, we can flush the dirty pages out to disk
  */
-static void bitmap_file_set_bit(struct bitmap *bitmap, sector_t block)
+static void md_bitmap_file_set_bit(struct bitmap *bitmap, sector_t block)
 {
 	unsigned long bit;
 	struct page *page;
@@ -952,7 +952,7 @@ static void bitmap_file_set_bit(struct bitmap *bitmap, sector_t block)
 	set_page_attr(bitmap, page->index - node_offset, BITMAP_PAGE_DIRTY);
 }
 
-static void bitmap_file_clear_bit(struct bitmap *bitmap, sector_t block)
+static void md_bitmap_file_clear_bit(struct bitmap *bitmap, sector_t block)
 {
 	unsigned long bit;
 	struct page *page;
@@ -980,7 +980,7 @@ static void bitmap_file_clear_bit(struct bitmap *bitmap, sector_t block)
 	}
 }
 
-static int bitmap_file_test_bit(struct bitmap *bitmap, sector_t block)
+static int md_bitmap_file_test_bit(struct bitmap *bitmap, sector_t block)
 {
 	unsigned long bit;
 	struct page *page;
@@ -1005,7 +1005,7 @@ static int bitmap_file_test_bit(struct bitmap *bitmap, sector_t block)
 /* this gets called when the md device is ready to unplug its underlying
  * (slave) device queues -- before we let any writes go down, we need to
  * sync the dirty pages of the bitmap file to disk */
-void bitmap_unplug(struct bitmap *bitmap)
+void md_bitmap_unplug(struct bitmap *bitmap)
 {
 	unsigned long i;
 	int dirty, need_write;
@@ -1025,7 +1025,7 @@ void bitmap_unplug(struct bitmap *bitmap)
 						      BITMAP_PAGE_NEEDWRITE);
 		if (dirty || need_write) {
 			if (!writing) {
-				bitmap_wait_writes(bitmap);
+				md_bitmap_wait_writes(bitmap);
 				if (bitmap->mddev->queue)
 					blk_add_trace_msg(bitmap->mddev->queue,
 							  "md bitmap_unplug");
@@ -1036,14 +1036,14 @@ void bitmap_unplug(struct bitmap *bitmap)
 		}
 	}
 	if (writing)
-		bitmap_wait_writes(bitmap);
+		md_bitmap_wait_writes(bitmap);
 
 	if (test_bit(BITMAP_WRITE_ERROR, &bitmap->flags))
-		bitmap_file_kick(bitmap);
+		md_bitmap_file_kick(bitmap);
 }
-EXPORT_SYMBOL(bitmap_unplug);
+EXPORT_SYMBOL(md_bitmap_unplug);
 
-static void bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int needed);
+static void md_bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int needed);
 /* * bitmap_init_from_disk -- called at bitmap_create time to initialize
  * the in-memory bitmap from the on-disk bitmap -- also, sets up the
  * memory mapping of the bitmap file
@@ -1055,7 +1055,7 @@ static void bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int n
  * We ignore all bits for sectors that end earlier than 'start'.
  * This is used when reading an out-of-date bitmap...
  */
-static int bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
+static int md_bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
 {
 	unsigned long i, chunks, index, oldindex, bit, node_offset = 0;
 	struct page *page = NULL;
@@ -1078,9 +1078,9 @@ static int bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
 			/* if the disk bit is set, set the memory bit */
 			int needed = ((sector_t)(i+1) << (bitmap->counts.chunkshift)
 				      >= start);
-			bitmap_set_memory_bits(bitmap,
+			md_bitmap_set_memory_bits(bitmap,
-					       (sector_t)i << bitmap->counts.chunkshift,
+						  (sector_t)i << bitmap->counts.chunkshift,
-					       needed);
+						  needed);
 		}
 		return 0;
 	}
@@ -1159,9 +1159,9 @@ static int bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
 			/* if the disk bit is set, set the memory bit */
 			int needed = ((sector_t)(i+1) << bitmap->counts.chunkshift
 				      >= start);
-			bitmap_set_memory_bits(bitmap,
+			md_bitmap_set_memory_bits(bitmap,
-					       (sector_t)i << bitmap->counts.chunkshift,
+						  (sector_t)i << bitmap->counts.chunkshift,
-					       needed);
+						  needed);
 			bit_cnt++;
 		}
 		offset = 0;
@@ -1179,7 +1179,7 @@ static int bitmap_init_from_disk(struct bitmap *bitmap, sector_t start)
 	return ret;
 }
 
-void bitmap_write_all(struct bitmap *bitmap)
+void md_bitmap_write_all(struct bitmap *bitmap)
 {
 	/* We don't actually write all bitmap blocks here,
 	 * just flag them as needing to be written
@@ -1198,16 +1198,16 @@ void bitmap_write_all(struct bitmap *bitmap)
 	bitmap->allclean = 0;
 }
 
-static void bitmap_count_page(struct bitmap_counts *bitmap,
+static void md_bitmap_count_page(struct bitmap_counts *bitmap,
-			      sector_t offset, int inc)
+				 sector_t offset, int inc)
 {
 	sector_t chunk = offset >> bitmap->chunkshift;
 	unsigned long page = chunk >> PAGE_COUNTER_SHIFT;
 	bitmap->bp[page].count += inc;
-	bitmap_checkfree(bitmap, page);
+	md_bitmap_checkfree(bitmap, page);
 }
 
-static void bitmap_set_pending(struct bitmap_counts *bitmap, sector_t offset)
+static void md_bitmap_set_pending(struct bitmap_counts *bitmap, sector_t offset)
 {
 	sector_t chunk = offset >> bitmap->chunkshift;
 	unsigned long page = chunk >> PAGE_COUNTER_SHIFT;
@@ -1217,16 +1217,16 @@ static void bitmap_set_pending(struct bitmap_counts *bitmap, sector_t offset)
 		bp->pending = 1;
 }
 
-static bitmap_counter_t *bitmap_get_counter(struct bitmap_counts *bitmap,
+static bitmap_counter_t *md_bitmap_get_counter(struct bitmap_counts *bitmap,
-					    sector_t offset, sector_t *blocks,
+					       sector_t offset, sector_t *blocks,
-					    int create);
+					       int create);
 
 /*
  * bitmap daemon -- periodically wakes up to clean bits and flush pages
  *			out to disk
  */
 
-void bitmap_daemon_work(struct mddev *mddev)
+void md_bitmap_daemon_work(struct mddev *mddev)
 {
 	struct bitmap *bitmap;
 	unsigned long j;
@@ -1301,10 +1301,8 @@ void bitmap_daemon_work(struct mddev *mddev)
 			}
 			counts->bp[j >> PAGE_COUNTER_SHIFT].pending = 0;
 		}
-		bmc = bitmap_get_counter(counts,
-					 block,
-					 &blocks, 0);
 
+		bmc = md_bitmap_get_counter(counts, block, &blocks, 0);
 		if (!bmc) {
 			j |= PAGE_COUNTER_MASK;
 			continue;
@@ -1312,17 +1310,17 @@ void bitmap_daemon_work(struct mddev *mddev)
 		if (*bmc == 1 && !bitmap->need_sync) {
 			/* We can clear the bit */
 			*bmc = 0;
-			bitmap_count_page(counts, block, -1);
+			md_bitmap_count_page(counts, block, -1);
-			bitmap_file_clear_bit(bitmap, block);
+			md_bitmap_file_clear_bit(bitmap, block);
 		} else if (*bmc && *bmc <= 2) {
 			*bmc = 1;
-			bitmap_set_pending(counts, block);
+			md_bitmap_set_pending(counts, block);
 			bitmap->allclean = 0;
 		}
 	}
 	spin_unlock_irq(&counts->lock);
 
-	bitmap_wait_writes(bitmap);
+	md_bitmap_wait_writes(bitmap);
 	/* Now start writeout on any page in NEEDWRITE that isn't DIRTY.
 	 * DIRTY pages need to be written by bitmap_unplug so it can wait
 	 * for them.
@@ -1352,9 +1350,9 @@ void bitmap_daemon_work(struct mddev *mddev)
 	mutex_unlock(&mddev->bitmap_info.mutex);
 }
 
-static bitmap_counter_t *bitmap_get_counter(struct bitmap_counts *bitmap,
+static bitmap_counter_t *md_bitmap_get_counter(struct bitmap_counts *bitmap,
-					    sector_t offset, sector_t *blocks,
+					       sector_t offset, sector_t *blocks,
-					    int create)
+					       int create)
 __releases(bitmap->lock)
 __acquires(bitmap->lock)
 {
@@ -1368,7 +1366,7 @@ __acquires(bitmap->lock)
 	sector_t csize;
 	int err;
 
-	err = bitmap_checkpage(bitmap, page, create, 0);
+	err = md_bitmap_checkpage(bitmap, page, create, 0);
 
 	if (bitmap->bp[page].hijacked ||
 	    bitmap->bp[page].map == NULL)
@@ -1394,7 +1392,7 @@ __acquires(bitmap->lock)
 			&(bitmap->bp[page].map[pageoff]);
 }
 
-int bitmap_startwrite(struct bitmap *bitmap, sector_t offset, unsigned long sectors, int behind)
+int md_bitmap_startwrite(struct bitmap *bitmap, sector_t offset, unsigned long sectors, int behind)
 {
 	if (!bitmap)
 		return 0;
@@ -1415,7 +1413,7 @@ int bitmap_startwrite(struct bitmap *bitmap, sector_t offset, unsigned long sect
 		bitmap_counter_t *bmc;
 
 		spin_lock_irq(&bitmap->counts.lock);
-		bmc = bitmap_get_counter(&bitmap->counts, offset, &blocks, 1);
+		bmc = md_bitmap_get_counter(&bitmap->counts, offset, &blocks, 1);
 		if (!bmc) {
 			spin_unlock_irq(&bitmap->counts.lock);
 			return 0;
@@ -1437,8 +1435,8 @@ int bitmap_startwrite(struct bitmap *bitmap, sector_t offset, unsigned long sect
 
 		switch (*bmc) {
 		case 0:
-			bitmap_file_set_bit(bitmap, offset);
+			md_bitmap_file_set_bit(bitmap, offset);
-			bitmap_count_page(&bitmap->counts, offset, 1);
+			md_bitmap_count_page(&bitmap->counts, offset, 1);
 			/* fall through */
 		case 1:
 			*bmc = 2;
@@ -1456,10 +1454,10 @@ int bitmap_startwrite(struct bitmap *bitmap, sector_t offset, unsigned long sect
 	}
 	return 0;
 }
-EXPORT_SYMBOL(bitmap_startwrite);
+EXPORT_SYMBOL(md_bitmap_startwrite);
 
-void bitmap_endwrite(struct bitmap *bitmap, sector_t offset, unsigned long sectors,
+void md_bitmap_endwrite(struct bitmap *bitmap, sector_t offset,
-		     int success, int behind)
+			unsigned long sectors, int success, int behind)
 {
 	if (!bitmap)
 		return;
@@ -1477,7 +1475,7 @@ void bitmap_endwrite(struct bitmap *bitmap, sector_t offset, unsigned long secto
 		bitmap_counter_t *bmc;
 
 		spin_lock_irqsave(&bitmap->counts.lock, flags);
-		bmc = bitmap_get_counter(&bitmap->counts, offset, &blocks, 0);
+		bmc = md_bitmap_get_counter(&bitmap->counts, offset, &blocks, 0);
 		if (!bmc) {
 			spin_unlock_irqrestore(&bitmap->counts.lock, flags);
 			return;
@@ -1498,7 +1496,7 @@ void bitmap_endwrite(struct bitmap *bitmap, sector_t offset, unsigned long secto
 
 		(*bmc)--;
 		if (*bmc <= 2) {
-			bitmap_set_pending(&bitmap->counts, offset);
+			md_bitmap_set_pending(&bitmap->counts, offset);
 			bitmap->allclean = 0;
 		}
 		spin_unlock_irqrestore(&bitmap->counts.lock, flags);
@@ -1509,7 +1507,7 @@ void bitmap_endwrite(struct bitmap *bitmap, sector_t offset, unsigned long secto
 			sectors = 0;
 	}
 }
-EXPORT_SYMBOL(bitmap_endwrite);
+EXPORT_SYMBOL(md_bitmap_endwrite);
 
 static int __bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks,
 			       int degraded)
@@ -1521,7 +1519,7 @@ static int __bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t
 		return 1; /* always resync if no bitmap */
 	}
 	spin_lock_irq(&bitmap->counts.lock);
-	bmc = bitmap_get_counter(&bitmap->counts, offset, blocks, 0);
+	bmc = md_bitmap_get_counter(&bitmap->counts, offset, blocks, 0);
 	rv = 0;
 	if (bmc) {
 		/* locked */
@@ -1539,8 +1537,8 @@ static int __bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t
 	return rv;
 }
 
-int bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks,
+int md_bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks,
-		      int degraded)
+			 int degraded)
 {
 	/* bitmap_start_sync must always report on multiples of whole
 	 * pages, otherwise resync (which is very PAGE_SIZE based) will
@@ -1561,9 +1559,9 @@ int bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks,
 	}
 	return rv;
 }
-EXPORT_SYMBOL(bitmap_start_sync);
+EXPORT_SYMBOL(md_bitmap_start_sync);
 
-void bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, int aborted)
+void md_bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, int aborted)
 {
 	bitmap_counter_t *bmc;
 	unsigned long flags;
@@ -1573,7 +1571,7 @@ void bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, i
 		return;
 	}
 	spin_lock_irqsave(&bitmap->counts.lock, flags);
-	bmc = bitmap_get_counter(&bitmap->counts, offset, blocks, 0);
+	bmc = md_bitmap_get_counter(&bitmap->counts, offset, blocks, 0);
 	if (bmc == NULL)
 		goto unlock;
 	/* locked */
@@ -1584,7 +1582,7 @@ void bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, i
 			*bmc |= NEEDED_MASK;
 		else {
 			if (*bmc <= 2) {
-				bitmap_set_pending(&bitmap->counts, offset);
+				md_bitmap_set_pending(&bitmap->counts, offset);
 				bitmap->allclean = 0;
 			}
 		}
@@ -1592,9 +1590,9 @@ void bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, i
  unlock:
 	spin_unlock_irqrestore(&bitmap->counts.lock, flags);
 }
-EXPORT_SYMBOL(bitmap_end_sync);
+EXPORT_SYMBOL(md_bitmap_end_sync);
 
-void bitmap_close_sync(struct bitmap *bitmap)
+void md_bitmap_close_sync(struct bitmap *bitmap)
 {
 	/* Sync has finished, and any bitmap chunks that weren't synced
 	 * properly have been aborted.  It remains to us to clear the
@@ -1605,13 +1603,13 @@ void bitmap_close_sync(struct bitmap *bitmap)
 	if (!bitmap)
 		return;
 	while (sector < bitmap->mddev->resync_max_sectors) {
-		bitmap_end_sync(bitmap, sector, &blocks, 0);
+		md_bitmap_end_sync(bitmap, sector, &blocks, 0);
 		sector += blocks;
 	}
 }
-EXPORT_SYMBOL(bitmap_close_sync);
+EXPORT_SYMBOL(md_bitmap_close_sync);
 
-void bitmap_cond_end_sync(struct bitmap *bitmap, sector_t sector, bool force)
+void md_bitmap_cond_end_sync(struct bitmap *bitmap, sector_t sector, bool force)
 {
 	sector_t s = 0;
 	sector_t blocks;
@@ -1633,15 +1631,15 @@ void bitmap_cond_end_sync(struct bitmap *bitmap, sector_t sector, bool force)
 	sector &= ~((1ULL << bitmap->counts.chunkshift) - 1);
 	s = 0;
 	while (s < sector && s < bitmap->mddev->resync_max_sectors) {
-		bitmap_end_sync(bitmap, s, &blocks, 0);
+		md_bitmap_end_sync(bitmap, s, &blocks, 0);
 		s += blocks;
 	}
 	bitmap->last_end_sync = jiffies;
 	sysfs_notify(&bitmap->mddev->kobj, NULL, "sync_completed");
 }
-EXPORT_SYMBOL(bitmap_cond_end_sync);
+EXPORT_SYMBOL(md_bitmap_cond_end_sync);
 
-void bitmap_sync_with_cluster(struct mddev *mddev,
+void md_bitmap_sync_with_cluster(struct mddev *mddev,
 			      sector_t old_lo, sector_t old_hi,
 			      sector_t new_lo, sector_t new_hi)
 {
@@ -1649,20 +1647,20 @@ void bitmap_sync_with_cluster(struct mddev *mddev,
 	sector_t sector, blocks = 0;
 
 	for (sector = old_lo; sector < new_lo; ) {
-		bitmap_end_sync(bitmap, sector, &blocks, 0);
+		md_bitmap_end_sync(bitmap, sector, &blocks, 0);
 		sector += blocks;
 	}
 	WARN((blocks > new_lo) && old_lo, "alignment is not correct for lo\n");
 
 	for (sector = old_hi; sector < new_hi; ) {
-		bitmap_start_sync(bitmap, sector, &blocks, 0);
+		md_bitmap_start_sync(bitmap, sector, &blocks, 0);
 		sector += blocks;
 	}
 	WARN((blocks > new_hi) && old_hi, "alignment is not correct for hi\n");
 }
-EXPORT_SYMBOL(bitmap_sync_with_cluster);
+EXPORT_SYMBOL(md_bitmap_sync_with_cluster);
 
-static void bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int needed)
+static void md_bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int needed)
 {
 	/* For each chunk covered by any of these sectors, set the
 	 * counter to 2 and possibly set resync_needed.  They should all
@@ -1672,15 +1670,15 @@ static void bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int n
 	sector_t secs;
 	bitmap_counter_t *bmc;
 	spin_lock_irq(&bitmap->counts.lock);
-	bmc = bitmap_get_counter(&bitmap->counts, offset, &secs, 1);
+	bmc = md_bitmap_get_counter(&bitmap->counts, offset, &secs, 1);
 	if (!bmc) {
 		spin_unlock_irq(&bitmap->counts.lock);
 		return;
 	}
 	if (!*bmc) {
 		*bmc = 2;
-		bitmap_count_page(&bitmap->counts, offset, 1);
+		md_bitmap_count_page(&bitmap->counts, offset, 1);
-		bitmap_set_pending(&bitmap->counts, offset);
+		md_bitmap_set_pending(&bitmap->counts, offset);
 		bitmap->allclean = 0;
 	}
 	if (needed)
@@ -1689,14 +1687,14 @@ static void bitmap_set_memory_bits(struct bitmap *bitmap, sector_t offset, int n
 }
 
 /* dirty the memory and file bits for bitmap chunks "s" to "e" */
-void bitmap_dirty_bits(struct bitmap *bitmap, unsigned long s, unsigned long e)
+void md_bitmap_dirty_bits(struct bitmap *bitmap, unsigned long s, unsigned long e)
 {
 	unsigned long chunk;
 
 	for (chunk = s; chunk <= e; chunk++) {
 		sector_t sec = (sector_t)chunk << bitmap->counts.chunkshift;
-		bitmap_set_memory_bits(bitmap, sec, 1);
+		md_bitmap_set_memory_bits(bitmap, sec, 1);
-		bitmap_file_set_bit(bitmap, sec);
+		md_bitmap_file_set_bit(bitmap, sec);
 		if (sec < bitmap->mddev->recovery_cp)
 			/* We are asserting that the array is dirty,
 			 * so move the recovery_cp address back so
@@ -1709,7 +1707,7 @@ void bitmap_dirty_bits(struct bitmap *bitmap, unsigned long s, unsigned long e)
 /*
  * flush out any pending updates
  */
-void bitmap_flush(struct mddev *mddev)
+void md_bitmap_flush(struct mddev *mddev)
 {
 	struct bitmap *bitmap = mddev->bitmap;
 	long sleep;
@@ -1722,18 +1720,18 @@ void bitmap_flush(struct mddev *mddev)
 	 */
 	sleep = mddev->bitmap_info.daemon_sleep * 2;
 	bitmap->daemon_lastrun -= sleep;
-	bitmap_daemon_work(mddev);
+	md_bitmap_daemon_work(mddev);
 	bitmap->daemon_lastrun -= sleep;
-	bitmap_daemon_work(mddev);
+	md_bitmap_daemon_work(mddev);
 	bitmap->daemon_lastrun -= sleep;
-	bitmap_daemon_work(mddev);
+	md_bitmap_daemon_work(mddev);
-	bitmap_update_sb(bitmap);
+	md_bitmap_update_sb(bitmap);
 }
 
 /*
  * free memory that was allocated
  */
-void bitmap_free(struct bitmap *bitmap)
+void md_bitmap_free(struct bitmap *bitmap)
 {
 	unsigned long k, pages;
 	struct bitmap_page *bp;
@@ -1753,7 +1751,7 @@ void bitmap_free(struct bitmap *bitmap)
 		   atomic_read(&bitmap->pending_writes) == 0);
 
 	/* release the bitmap file  */
-	bitmap_file_unmap(&bitmap->storage);
+	md_bitmap_file_unmap(&bitmap->storage);
 
 	bp = bitmap->counts.bp;
 	pages = bitmap->counts.pages;
@@ -1767,9 +1765,9 @@ void bitmap_free(struct bitmap *bitmap)
 	kfree(bp);
 	kfree(bitmap);
 }
-EXPORT_SYMBOL(bitmap_free);
+EXPORT_SYMBOL(md_bitmap_free);
 
-void bitmap_wait_behind_writes(struct mddev *mddev)
+void md_bitmap_wait_behind_writes(struct mddev *mddev)
 {
 	struct bitmap *bitmap = mddev->bitmap;
 
@@ -1783,14 +1781,14 @@ void bitmap_wait_behind_writes(struct mddev *mddev)
 	}
 }
 
-void bitmap_destroy(struct mddev *mddev)
+void md_bitmap_destroy(struct mddev *mddev)
 {
 	struct bitmap *bitmap = mddev->bitmap;
 
 	if (!bitmap) /* there was no bitmap */
 		return;
 
-	bitmap_wait_behind_writes(mddev);
+	md_bitmap_wait_behind_writes(mddev);
 
 	mutex_lock(&mddev->bitmap_info.mutex);
 	spin_lock(&mddev->lock);
@@ -1800,7 +1798,7 @@ void bitmap_destroy(struct mddev *mddev)
 	if (mddev->thread)
 		mddev->thread->timeout = MAX_SCHEDULE_TIMEOUT;
 
-	bitmap_free(bitmap);
+	md_bitmap_free(bitmap);
 }
 
 /*
@@ -1808,7 +1806,7 @@ void bitmap_destroy(struct mddev *mddev)
  * if this returns an error, bitmap_destroy must be called to do clean up
  * once mddev->bitmap is set
  */
-struct bitmap *bitmap_create(struct mddev *mddev, int slot)
+struct bitmap *md_bitmap_create(struct mddev *mddev, int slot)
 {
 	struct bitmap *bitmap;
 	sector_t blocks = mddev->resync_max_sectors;
@@ -1863,9 +1861,9 @@ struct bitmap *bitmap_create(struct mddev *mddev, int slot)
 		 * instructing us to create a new on-disk bitmap instance.
 		 */
 		if (test_and_clear_bit(MD_ARRAY_FIRST_USE, &mddev->flags))
-			err = bitmap_new_disk_sb(bitmap);
+			err = md_bitmap_new_disk_sb(bitmap);
 		else
-			err = bitmap_read_sb(bitmap);
+			err = md_bitmap_read_sb(bitmap);
 	} else {
 		err = 0;
 		if (mddev->bitmap_info.chunksize == 0 ||
@@ -1878,7 +1876,7 @@ struct bitmap *bitmap_create(struct mddev *mddev, int slot)
 		goto error;
 
 	bitmap->daemon_lastrun = jiffies;
-	err = bitmap_resize(bitmap, blocks, mddev->bitmap_info.chunksize, 1);
+	err = md_bitmap_resize(bitmap, blocks, mddev->bitmap_info.chunksize, 1);
 	if (err)
 		goto error;
 
@@ -1891,11 +1889,11 @@ struct bitmap *bitmap_create(struct mddev *mddev, int slot)
 
 	return bitmap;
  error:
-	bitmap_free(bitmap);
+	md_bitmap_free(bitmap);
 	return ERR_PTR(err);
 }
 
-int bitmap_load(struct mddev *mddev)
+int md_bitmap_load(struct mddev *mddev)
 {
 	int err = 0;
 	sector_t start = 0;
@@ -1915,10 +1913,10 @@ int bitmap_load(struct mddev *mddev)
 	 */
 	while (sector < mddev->resync_max_sectors) {
 		sector_t blocks;
-		bitmap_start_sync(bitmap, sector, &blocks, 0);
+		md_bitmap_start_sync(bitmap, sector, &blocks, 0);
 		sector += blocks;
 	}
-	bitmap_close_sync(bitmap);
+	md_bitmap_close_sync(bitmap);
 
 	if (mddev->degraded == 0
 	    || bitmap->events_cleared == mddev->events)
@@ -1927,7 +1925,7 @@ int bitmap_load(struct mddev *mddev)
 		start = mddev->recovery_cp;
 
 	mutex_lock(&mddev->bitmap_info.mutex);
-	err = bitmap_init_from_disk(bitmap, start);
+	err = md_bitmap_init_from_disk(bitmap, start);
 	mutex_unlock(&mddev->bitmap_info.mutex);
 
 	if (err)
@@ -1940,29 +1938,29 @@ int bitmap_load(struct mddev *mddev)
 	mddev->thread->timeout = mddev->bitmap_info.daemon_sleep;
 	md_wakeup_thread(mddev->thread);
 
-	bitmap_update_sb(bitmap);
+	md_bitmap_update_sb(bitmap);
 
 	if (test_bit(BITMAP_WRITE_ERROR, &bitmap->flags))
 		err = -EIO;
 out:
 	return err;
 }
-EXPORT_SYMBOL_GPL(bitmap_load);
+EXPORT_SYMBOL_GPL(md_bitmap_load);
 
 struct bitmap *get_bitmap_from_slot(struct mddev *mddev, int slot)
 {
 	int rv = 0;
 	struct bitmap *bitmap;
 
-	bitmap = bitmap_create(mddev, slot);
+	bitmap = md_bitmap_create(mddev, slot);
 	if (IS_ERR(bitmap)) {
 		rv = PTR_ERR(bitmap);
 		return ERR_PTR(rv);
 	}
 
-	rv = bitmap_init_from_disk(bitmap, 0);
+	rv = md_bitmap_init_from_disk(bitmap, 0);
 	if (rv) {
-		bitmap_free(bitmap);
+		md_bitmap_free(bitmap);
 		return ERR_PTR(rv);
 	}
 
@@ -1973,7 +1971,7 @@ EXPORT_SYMBOL(get_bitmap_from_slot);
 /* Loads the bitmap associated with slot and copies the resync information
  * to our bitmap
  */
-int bitmap_copy_from_slot(struct mddev *mddev, int slot,
+int md_bitmap_copy_from_slot(struct mddev *mddev, int slot,
 		sector_t *low, sector_t *high, bool clear_bits)
 {
 	int rv = 0, i, j;
@@ -1990,35 +1988,35 @@ int bitmap_copy_from_slot(struct mddev *mddev, int slot,
 	counts = &bitmap->counts;
 	for (j = 0; j < counts->chunks; j++) {
 		block = (sector_t)j << counts->chunkshift;
-		if (bitmap_file_test_bit(bitmap, block)) {
+		if (md_bitmap_file_test_bit(bitmap, block)) {
 			if (!lo)
 				lo = block;
 			hi = block;
-			bitmap_file_clear_bit(bitmap, block);
+			md_bitmap_file_clear_bit(bitmap, block);
-			bitmap_set_memory_bits(mddev->bitmap, block, 1);
+			md_bitmap_set_memory_bits(mddev->bitmap, block, 1);
-			bitmap_file_set_bit(mddev->bitmap, block);
+			md_bitmap_file_set_bit(mddev->bitmap, block);
 		}
 	}
 
 	if (clear_bits) {
-		bitmap_update_sb(bitmap);
+		md_bitmap_update_sb(bitmap);
 		/* BITMAP_PAGE_PENDING is set, but bitmap_unplug needs
 		 * BITMAP_PAGE_DIRTY or _NEEDWRITE to write ... */
 		for (i = 0; i < bitmap->storage.file_pages; i++)
 			if (test_page_attr(bitmap, i, BITMAP_PAGE_PENDING))
 				set_page_attr(bitmap, i, BITMAP_PAGE_NEEDWRITE);
-		bitmap_unplug(bitmap);
+		md_bitmap_unplug(bitmap);
 	}
-	bitmap_unplug(mddev->bitmap);
+	md_bitmap_unplug(mddev->bitmap);
 	*low = lo;
 	*high = hi;
 
 	return rv;
 }
-EXPORT_SYMBOL_GPL(bitmap_copy_from_slot);
+EXPORT_SYMBOL_GPL(md_bitmap_copy_from_slot);
 
 
-void bitmap_status(struct seq_file *seq, struct bitmap *bitmap)
+void md_bitmap_status(struct seq_file *seq, struct bitmap *bitmap)
 {
 	unsigned long chunk_kb;
 	struct bitmap_counts *counts;
@@ -2045,7 +2043,7 @@ void bitmap_status(struct seq_file *seq, struct bitmap *bitmap)
 	seq_printf(seq, "\n");
 }
 
-int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
+int md_bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 		  int chunksize, int init)
 {
 	/* If chunk_size is 0, choose an appropriate chunk size.
@@ -2106,12 +2104,12 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 	chunks = DIV_ROUND_UP_SECTOR_T(blocks, 1 << chunkshift);
 	memset(&store, 0, sizeof(store));
 	if (bitmap->mddev->bitmap_info.offset || bitmap->mddev->bitmap_info.file)
-		ret = bitmap_storage_alloc(&store, chunks,
+		ret = md_bitmap_storage_alloc(&store, chunks,
-					   !bitmap->mddev->bitmap_info.external,
+					      !bitmap->mddev->bitmap_info.external,
-					   mddev_is_clustered(bitmap->mddev)
+					      mddev_is_clustered(bitmap->mddev)
-					   ? bitmap->cluster_slot : 0);
+					      ? bitmap->cluster_slot : 0);
 	if (ret) {
-		bitmap_file_unmap(&store);
+		md_bitmap_file_unmap(&store);
 		goto err;
 	}
 
@@ -2120,7 +2118,7 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 	new_bp = kcalloc(pages, sizeof(*new_bp), GFP_KERNEL);
 	ret = -ENOMEM;
 	if (!new_bp) {
-		bitmap_file_unmap(&store);
+		md_bitmap_file_unmap(&store);
 		goto err;
 	}
 
@@ -2134,7 +2132,7 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 		memcpy(page_address(store.sb_page),
 		       page_address(bitmap->storage.sb_page),
 		       sizeof(bitmap_super_t));
-	bitmap_file_unmap(&bitmap->storage);
+	md_bitmap_file_unmap(&bitmap->storage);
 	bitmap->storage = store;
 
 	old_counts = bitmap->counts;
@@ -2154,7 +2152,7 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 	if (mddev_is_clustered(bitmap->mddev)) {
 		unsigned long page;
 		for (page = 0; page < pages; page++) {
-			ret = bitmap_checkpage(&bitmap->counts, page, 1, 1);
+			ret = md_bitmap_checkpage(&bitmap->counts, page, 1, 1);
 			if (ret) {
 				unsigned long k;
 
@@ -2184,27 +2182,23 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 		bitmap_counter_t *bmc_old, *bmc_new;
 		int set;
 
-		bmc_old = bitmap_get_counter(&old_counts, block,
+		bmc_old = md_bitmap_get_counter(&old_counts, block, &old_blocks, 0);
-					     &old_blocks, 0);
 		set = bmc_old && NEEDED(*bmc_old);
 
 		if (set) {
-			bmc_new = bitmap_get_counter(&bitmap->counts, block,
+			bmc_new = md_bitmap_get_counter(&bitmap->counts, block, &new_blocks, 1);
-						     &new_blocks, 1);
 			if (*bmc_new == 0) {
 				/* need to set on-disk bits too. */
 				sector_t end = block + new_blocks;
 				sector_t start = block >> chunkshift;
 				start <<= chunkshift;
 				while (start < end) {
-					bitmap_file_set_bit(bitmap, block);
+					md_bitmap_file_set_bit(bitmap, block);
 					start += 1 << chunkshift;
 				}
 				*bmc_new = 2;
-				bitmap_count_page(&bitmap->counts,
+				md_bitmap_count_page(&bitmap->counts, block, 1);
-						  block, 1);
+				md_bitmap_set_pending(&bitmap->counts, block);
-				bitmap_set_pending(&bitmap->counts,
-						   block);
 			}
 			*bmc_new |= NEEDED_MASK;
 			if (new_blocks < old_blocks)
@@ -2225,18 +2219,15 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 		int i;
 		while (block < (chunks << chunkshift)) {
 			bitmap_counter_t *bmc;
-			bmc = bitmap_get_counter(&bitmap->counts, block,
+			bmc = md_bitmap_get_counter(&bitmap->counts, block, &new_blocks, 1);
-						 &new_blocks, 1);
 			if (bmc) {
 				/* new space.  It needs to be resynced, so
 				 * we set NEEDED_MASK.
 				 */
 				if (*bmc == 0) {
 					*bmc = NEEDED_MASK | 2;
-					bitmap_count_page(&bitmap->counts,
+					md_bitmap_count_page(&bitmap->counts, block, 1);
-							  block, 1);
+					md_bitmap_set_pending(&bitmap->counts, block);
-					bitmap_set_pending(&bitmap->counts,
-							   block);
 				}
 			}
 			block += new_blocks;
@@ -2247,14 +2238,14 @@ int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
 	spin_unlock_irq(&bitmap->counts.lock);
 
 	if (!init) {
-		bitmap_unplug(bitmap);
+		md_bitmap_unplug(bitmap);
 		bitmap->mddev->pers->quiesce(bitmap->mddev, 0);
 	}
 	ret = 0;
 err:
 	return ret;
 }
-EXPORT_SYMBOL_GPL(bitmap_resize);
+EXPORT_SYMBOL_GPL(md_bitmap_resize);
 
 static ssize_t
 location_show(struct mddev *mddev, char *page)
@@ -2298,7 +2289,7 @@ location_store(struct mddev *mddev, const char *buf, size_t len)
 		}
 		if (mddev->pers) {
 			mddev->pers->quiesce(mddev, 1);
-			bitmap_destroy(mddev);
+			md_bitmap_destroy(mddev);
 			mddev->pers->quiesce(mddev, 0);
 		}
 		mddev->bitmap_info.offset = 0;
@@ -2337,18 +2328,18 @@ location_store(struct mddev *mddev, const char *buf, size_t len)
 			if (mddev->pers) {
 				struct bitmap *bitmap;
 				mddev->pers->quiesce(mddev, 1);
-				bitmap = bitmap_create(mddev, -1);
+				bitmap = md_bitmap_create(mddev, -1);
 				if (IS_ERR(bitmap))
 					rv = PTR_ERR(bitmap);
 				else {
 					mddev->bitmap = bitmap;
-					rv = bitmap_load(mddev);
+					rv = md_bitmap_load(mddev);
 					if (rv)
 						mddev->bitmap_info.offset = 0;
 				}
 				mddev->pers->quiesce(mddev, 0);
 				if (rv) {
-					bitmap_destroy(mddev);
+					md_bitmap_destroy(mddev);
 					goto out;
 				}
 			}

drivers/md/md-bitmap.h

@@ -236,43 +236,43 @@ struct bitmap {
 /* the bitmap API */
 
 /* these are used only by md/bitmap */
-struct bitmap *bitmap_create(struct mddev *mddev, int slot);
+struct bitmap *md_bitmap_create(struct mddev *mddev, int slot);
-int bitmap_load(struct mddev *mddev);
+int md_bitmap_load(struct mddev *mddev);
-void bitmap_flush(struct mddev *mddev);
+void md_bitmap_flush(struct mddev *mddev);
-void bitmap_destroy(struct mddev *mddev);
+void md_bitmap_destroy(struct mddev *mddev);
 
-void bitmap_print_sb(struct bitmap *bitmap);
+void md_bitmap_print_sb(struct bitmap *bitmap);
-void bitmap_update_sb(struct bitmap *bitmap);
+void md_bitmap_update_sb(struct bitmap *bitmap);
-void bitmap_status(struct seq_file *seq, struct bitmap *bitmap);
+void md_bitmap_status(struct seq_file *seq, struct bitmap *bitmap);
 
-int  bitmap_setallbits(struct bitmap *bitmap);
+int  md_bitmap_setallbits(struct bitmap *bitmap);
-void bitmap_write_all(struct bitmap *bitmap);
+void md_bitmap_write_all(struct bitmap *bitmap);
 
-void bitmap_dirty_bits(struct bitmap *bitmap, unsigned long s, unsigned long e);
+void md_bitmap_dirty_bits(struct bitmap *bitmap, unsigned long s, unsigned long e);
 
 /* these are exported */
-int bitmap_startwrite(struct bitmap *bitmap, sector_t offset,
+int md_bitmap_startwrite(struct bitmap *bitmap, sector_t offset,
-			unsigned long sectors, int behind);
+			 unsigned long sectors, int behind);
-void bitmap_endwrite(struct bitmap *bitmap, sector_t offset,
+void md_bitmap_endwrite(struct bitmap *bitmap, sector_t offset,
 			unsigned long sectors, int success, int behind);
-int bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, int degraded);
+int md_bitmap_start_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, int degraded);
-void bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, int aborted);
+void md_bitmap_end_sync(struct bitmap *bitmap, sector_t offset, sector_t *blocks, int aborted);
-void bitmap_close_sync(struct bitmap *bitmap);
+void md_bitmap_close_sync(struct bitmap *bitmap);
-void bitmap_cond_end_sync(struct bitmap *bitmap, sector_t sector, bool force);
+void md_bitmap_cond_end_sync(struct bitmap *bitmap, sector_t sector, bool force);
-void bitmap_sync_with_cluster(struct mddev *mddev,
+void md_bitmap_sync_with_cluster(struct mddev *mddev,
-			      sector_t old_lo, sector_t old_hi,
+				 sector_t old_lo, sector_t old_hi,
-			      sector_t new_lo, sector_t new_hi);
+				 sector_t new_lo, sector_t new_hi);
 
-void bitmap_unplug(struct bitmap *bitmap);
+void md_bitmap_unplug(struct bitmap *bitmap);
-void bitmap_daemon_work(struct mddev *mddev);
+void md_bitmap_daemon_work(struct mddev *mddev);
 
-int bitmap_resize(struct bitmap *bitmap, sector_t blocks,
+int md_bitmap_resize(struct bitmap *bitmap, sector_t blocks,
-		  int chunksize, int init);
+		     int chunksize, int init);
 struct bitmap *get_bitmap_from_slot(struct mddev *mddev, int slot);
-int bitmap_copy_from_slot(struct mddev *mddev, int slot,
+int md_bitmap_copy_from_slot(struct mddev *mddev, int slot,
-				sector_t *lo, sector_t *hi, bool clear_bits);
+			     sector_t *lo, sector_t *hi, bool clear_bits);
-void bitmap_free(struct bitmap *bitmap);
+void md_bitmap_free(struct bitmap *bitmap);
-void bitmap_wait_behind_writes(struct mddev *mddev);
+void md_bitmap_wait_behind_writes(struct mddev *mddev);
 #endif
 
 #endif

drivers/md/md-cluster.c

@@ -317,7 +317,7 @@ static void recover_bitmaps(struct md_thread *thread)
 					str, ret);
 			goto clear_bit;
 		}
-		ret = bitmap_copy_from_slot(mddev, slot, &lo, &hi, true);
+		ret = md_bitmap_copy_from_slot(mddev, slot, &lo, &hi, true);
 		if (ret) {
 			pr_err("md-cluster: Could not copy data from bitmap %d\n", slot);
 			goto clear_bit;
@@ -492,9 +492,7 @@ static void process_suspend_info(struct mddev *mddev,
 	 * resync thread is running in another node,
 	 * so we don't need to do the resync again
 	 * with the same section */
-	bitmap_sync_with_cluster(mddev, cinfo->sync_low,
+	md_bitmap_sync_with_cluster(mddev, cinfo->sync_low, cinfo->sync_hi, lo, hi);
-					cinfo->sync_hi,
-					lo, hi);
 	cinfo->sync_low = lo;
 	cinfo->sync_hi = hi;
 
@@ -842,7 +840,7 @@ static int gather_all_resync_info(struct mddev *mddev, int total_slots)
 		}
 
 		/* Read the disk bitmap sb and check if it needs recovery */
-		ret = bitmap_copy_from_slot(mddev, i, &lo, &hi, false);
+		ret = md_bitmap_copy_from_slot(mddev, i, &lo, &hi, false);
 		if (ret) {
 			pr_warn("md-cluster: Could not gather bitmaps from slot %d", i);
 			lockres_free(bm_lockres);
@@ -1140,13 +1138,13 @@ static int cluster_check_sync_size(struct mddev *mddev)
 		bm_lockres = lockres_init(mddev, str, NULL, 1);
 		if (!bm_lockres) {
 			pr_err("md-cluster: Cannot initialize %s\n", str);
-			bitmap_free(bitmap);
+			md_bitmap_free(bitmap);
 			return -1;
 		}
 		bm_lockres->flags |= DLM_LKF_NOQUEUE;
 		rv = dlm_lock_sync(bm_lockres, DLM_LOCK_PW);
 		if (!rv)
-			bitmap_update_sb(bitmap);
+			md_bitmap_update_sb(bitmap);
 		lockres_free(bm_lockres);
 
 		sb = kmap_atomic(bitmap->storage.sb_page);
@@ -1154,11 +1152,11 @@ static int cluster_check_sync_size(struct mddev *mddev)
 			sync_size = sb->sync_size;
 		else if (sync_size != sb->sync_size) {
 			kunmap_atomic(sb);
-			bitmap_free(bitmap);
+			md_bitmap_free(bitmap);
 			return -1;
 		}
 		kunmap_atomic(sb);
-		bitmap_free(bitmap);
+		md_bitmap_free(bitmap);
 	}
 
 	return (my_sync_size == sync_size) ? 0 : -1;
@@ -1465,7 +1463,7 @@ static int gather_bitmaps(struct md_rdev *rdev)
 	for (sn = 0; sn < mddev->bitmap_info.nodes; sn++) {
 		if (sn == (cinfo->slot_number - 1))
 			continue;
-		err = bitmap_copy_from_slot(mddev, sn, &lo, &hi, false);
+		err = md_bitmap_copy_from_slot(mddev, sn, &lo, &hi, false);
 		if (err) {
 			pr_warn("md-cluster: Could not gather bitmaps from slot %d", sn);
 			goto out;

drivers/md/md.c

@@ -2568,7 +2568,7 @@ repeat:
 	if (mddev->queue)
 		blk_add_trace_msg(mddev->queue, "md md_update_sb");
 rewrite:
-	bitmap_update_sb(mddev->bitmap);
+	md_bitmap_update_sb(mddev->bitmap);
 	rdev_for_each(rdev, mddev) {
 		char b[BDEVNAME_SIZE];
 
@@ -4381,10 +4381,10 @@ bitmap_store(struct mddev *mddev, const char *buf, size_t len)
 			if (buf == end) break;
 		}
 		if (*end && !isspace(*end)) break;
-		bitmap_dirty_bits(mddev->bitmap, chunk, end_chunk);
+		md_bitmap_dirty_bits(mddev->bitmap, chunk, end_chunk);
 		buf = skip_spaces(end);
 	}
-	bitmap_unplug(mddev->bitmap); /* flush the bits to disk */
+	md_bitmap_unplug(mddev->bitmap); /* flush the bits to disk */
 out:
 	mddev_unlock(mddev);
 	return len;
@@ -5612,7 +5612,7 @@ int md_run(struct mddev *mddev)
 	    (mddev->bitmap_info.file || mddev->bitmap_info.offset)) {
 		struct bitmap *bitmap;
 
-		bitmap = bitmap_create(mddev, -1);
+		bitmap = md_bitmap_create(mddev, -1);
 		if (IS_ERR(bitmap)) {
 			err = PTR_ERR(bitmap);
 			pr_warn("%s: failed to create bitmap (%d)\n",
@@ -5627,7 +5627,7 @@ int md_run(struct mddev *mddev)
 			pers->free(mddev, mddev->private);
 		mddev->private = NULL;
 		module_put(pers->owner);
-		bitmap_destroy(mddev);
+		md_bitmap_destroy(mddev);
 		goto abort;
 	}
 	if (mddev->queue) {
@@ -5712,9 +5712,9 @@ static int do_md_run(struct mddev *mddev)
 	err = md_run(mddev);
 	if (err)
 		goto out;
-	err = bitmap_load(mddev);
+	err = md_bitmap_load(mddev);
 	if (err) {
-		bitmap_destroy(mddev);
+		md_bitmap_destroy(mddev);
 		goto out;
 	}
 
@@ -5856,7 +5856,7 @@ static void __md_stop_writes(struct mddev *mddev)
 		mddev->pers->quiesce(mddev, 1);
 		mddev->pers->quiesce(mddev, 0);
 	}
-	bitmap_flush(mddev);
+	md_bitmap_flush(mddev);
 
 	if (mddev->ro == 0 &&
 	    ((!mddev->in_sync && !mddev_is_clustered(mddev)) ||
@@ -5878,7 +5878,7 @@ EXPORT_SYMBOL_GPL(md_stop_writes);
 
 static void mddev_detach(struct mddev *mddev)
 {
-	bitmap_wait_behind_writes(mddev);
+	md_bitmap_wait_behind_writes(mddev);
 	if (mddev->pers && mddev->pers->quiesce) {
 		mddev->pers->quiesce(mddev, 1);
 		mddev->pers->quiesce(mddev, 0);
@@ -5891,7 +5891,7 @@ static void mddev_detach(struct mddev *mddev)
 static void __md_stop(struct mddev *mddev)
 {
 	struct md_personality *pers = mddev->pers;
-	bitmap_destroy(mddev);
+	md_bitmap_destroy(mddev);
 	mddev_detach(mddev);
 	/* Ensure ->event_work is done */
 	flush_workqueue(md_misc_wq);
@@ -6710,21 +6710,21 @@ static int set_bitmap_file(struct mddev *mddev, int fd)
 		if (fd >= 0) {
 			struct bitmap *bitmap;
 
-			bitmap = bitmap_create(mddev, -1);
+			bitmap = md_bitmap_create(mddev, -1);
 			mddev_suspend(mddev);
 			if (!IS_ERR(bitmap)) {
 				mddev->bitmap = bitmap;
-				err = bitmap_load(mddev);
+				err = md_bitmap_load(mddev);
 			} else
 				err = PTR_ERR(bitmap);
 			if (err) {
-				bitmap_destroy(mddev);
+				md_bitmap_destroy(mddev);
 				fd = -1;
 			}
 			mddev_resume(mddev);
 		} else if (fd < 0) {
 			mddev_suspend(mddev);
-			bitmap_destroy(mddev);
+			md_bitmap_destroy(mddev);
 			mddev_resume(mddev);
 		}
 	}
@@ -7010,15 +7010,15 @@ static int update_array_info(struct mddev *mddev, mdu_array_info_t *info)
 				mddev->bitmap_info.default_offset;
 			mddev->bitmap_info.space =
 				mddev->bitmap_info.default_space;
-			bitmap = bitmap_create(mddev, -1);
+			bitmap = md_bitmap_create(mddev, -1);
 			mddev_suspend(mddev);
 			if (!IS_ERR(bitmap)) {
 				mddev->bitmap = bitmap;
-				rv = bitmap_load(mddev);
+				rv = md_bitmap_load(mddev);
 			} else
 				rv = PTR_ERR(bitmap);
 			if (rv)
-				bitmap_destroy(mddev);
+				md_bitmap_destroy(mddev);
 			mddev_resume(mddev);
 		} else {
 			/* remove the bitmap */
@@ -7043,7 +7043,7 @@ static int update_array_info(struct mddev *mddev, mdu_array_info_t *info)
 				md_cluster_ops->leave(mddev);
 			}
 			mddev_suspend(mddev);
-			bitmap_destroy(mddev);
+			md_bitmap_destroy(mddev);
 			mddev_resume(mddev);
 			mddev->bitmap_info.offset = 0;
 		}
@@ -7923,7 +7923,7 @@ static int md_seq_show(struct seq_file *seq, void *v)
 		} else
 			seq_printf(seq, "\n       ");
 
-		bitmap_status(seq, mddev->bitmap);
+		md_bitmap_status(seq, mddev->bitmap);
 
 		seq_printf(seq, "\n");
 	}
@@ -8794,7 +8794,7 @@ void md_check_recovery(struct mddev *mddev)
 		return;
 
 	if (mddev->bitmap)
-		bitmap_daemon_work(mddev);
+		md_bitmap_daemon_work(mddev);
 
 	if (signal_pending(current)) {
 		if (mddev->pers->sync_request && !mddev->external) {
@@ -8931,7 +8931,7 @@ void md_check_recovery(struct mddev *mddev)
 				 * which has the bitmap stored on all devices.
 				 * So make sure all bitmap pages get written
 				 */
-				bitmap_write_all(mddev->bitmap);
+				md_bitmap_write_all(mddev->bitmap);
 			}
 			INIT_WORK(&mddev->del_work, md_start_sync);
 			queue_work(md_misc_wq, &mddev->del_work);
@@ -9179,7 +9179,7 @@ static void check_sb_changes(struct mddev *mddev, struct md_rdev *rdev)
 		if (ret)
 			pr_info("md-cluster: resize failed\n");
 		else
-			bitmap_update_sb(mddev->bitmap);
+			md_bitmap_update_sb(mddev->bitmap);
 	}
 
 	/* Check for change of roles in the active devices */

drivers/md/persistent-data/dm-space-map-common.c

@@ -69,9 +69,9 @@ static struct dm_block_validator index_validator = {
  */
 #define BITMAP_CSUM_XOR 240779
 
-static void bitmap_prepare_for_write(struct dm_block_validator *v,
+static void dm_bitmap_prepare_for_write(struct dm_block_validator *v,
-				     struct dm_block *b,
+					struct dm_block *b,
-				     size_t block_size)
+					size_t block_size)
 {
 	struct disk_bitmap_header *disk_header = dm_block_data(b);
 
@@ -81,9 +81,9 @@ static void bitmap_prepare_for_write(struct dm_block_validator *v,
 						       BITMAP_CSUM_XOR));
 }
 
-static int bitmap_check(struct dm_block_validator *v,
+static int dm_bitmap_check(struct dm_block_validator *v,
-			struct dm_block *b,
+			   struct dm_block *b,
-			size_t block_size)
+			   size_t block_size)
 {
 	struct disk_bitmap_header *disk_header = dm_block_data(b);
 	__le32 csum_disk;
@@ -108,8 +108,8 @@ static int bitmap_check(struct dm_block_validator *v,
 
 static struct dm_block_validator dm_sm_bitmap_validator = {
 	.name = "sm_bitmap",
-	.prepare_for_write = bitmap_prepare_for_write,
+	.prepare_for_write = dm_bitmap_prepare_for_write,
-	.check = bitmap_check
+	.check = dm_bitmap_check,
 };
 
 /*----------------------------------------------------------------*/
@@ -124,7 +124,7 @@ static void *dm_bitmap_data(struct dm_block *b)
 
 #define WORD_MASK_HIGH 0xAAAAAAAAAAAAAAAAULL
 
-static unsigned bitmap_word_used(void *addr, unsigned b)
+static unsigned dm_bitmap_word_used(void *addr, unsigned b)
 {
 	__le64 *words_le = addr;
 	__le64 *w_le = words_le + (b >> ENTRIES_SHIFT);
@@ -170,7 +170,7 @@ static int sm_find_free(void *addr, unsigned begin, unsigned end,
 {
 	while (begin < end) {
 		if (!(begin & (ENTRIES_PER_WORD - 1)) &&
-		    bitmap_word_used(addr, begin)) {
+		    dm_bitmap_word_used(addr, begin)) {
 			begin += ENTRIES_PER_WORD;
 			continue;
 		}

drivers/md/raid1.c

@@ -385,10 +385,10 @@ static void close_write(struct r1bio *r1_bio)
 		r1_bio->behind_master_bio = NULL;
 	}
 	/* clear the bitmap if all writes complete successfully */
-	bitmap_endwrite(r1_bio->mddev->bitmap, r1_bio->sector,
+	md_bitmap_endwrite(r1_bio->mddev->bitmap, r1_bio->sector,
-			r1_bio->sectors,
+			   r1_bio->sectors,
-			!test_bit(R1BIO_Degraded, &r1_bio->state),
+			   !test_bit(R1BIO_Degraded, &r1_bio->state),
-			test_bit(R1BIO_BehindIO, &r1_bio->state));
+			   test_bit(R1BIO_BehindIO, &r1_bio->state));
 	md_write_end(r1_bio->mddev);
 }
 
@@ -781,7 +781,7 @@ static int raid1_congested(struct mddev *mddev, int bits)
 static void flush_bio_list(struct r1conf *conf, struct bio *bio)
 {
 	/* flush any pending bitmap writes to disk before proceeding w/ I/O */
-	bitmap_unplug(conf->mddev->bitmap);
+	md_bitmap_unplug(conf->mddev->bitmap);
 	wake_up(&conf->wait_barrier);
 
 	while (bio) { /* submit pending writes */
@@ -1470,10 +1470,8 @@ static void raid1_write_request(struct mddev *mddev, struct bio *bio,
 				alloc_behind_master_bio(r1_bio, bio);
 			}
 
-			bitmap_startwrite(bitmap, r1_bio->sector,
+			md_bitmap_startwrite(bitmap, r1_bio->sector, r1_bio->sectors,
-					  r1_bio->sectors,
+					     test_bit(R1BIO_BehindIO, &r1_bio->state));
-					  test_bit(R1BIO_BehindIO,
-						   &r1_bio->state));
 			first_clone = 0;
 		}
 
@@ -1880,8 +1878,7 @@ static void end_sync_write(struct bio *bio)
 		long sectors_to_go = r1_bio->sectors;
 		/* make sure these bits doesn't get cleared. */
 		do {
-			bitmap_end_sync(mddev->bitmap, s,
+			md_bitmap_end_sync(mddev->bitmap, s, &sync_blocks, 1);
-					&sync_blocks, 1);
 			s += sync_blocks;
 			sectors_to_go -= sync_blocks;
 		} while (sectors_to_go > 0);
@@ -2626,12 +2623,12 @@ static sector_t raid1_sync_request(struct mddev *mddev, sector_t sector_nr,
 		 * We can find the current addess in mddev->curr_resync
 		 */
 		if (mddev->curr_resync < max_sector) /* aborted */
-			bitmap_end_sync(mddev->bitmap, mddev->curr_resync,
+			md_bitmap_end_sync(mddev->bitmap, mddev->curr_resync,
-						&sync_blocks, 1);
+					   &sync_blocks, 1);
 		else /* completed sync */
 			conf->fullsync = 0;
 
-		bitmap_close_sync(mddev->bitmap);
+		md_bitmap_close_sync(mddev->bitmap);
 		close_sync(conf);
 
 		if (mddev_is_clustered(mddev)) {
@@ -2651,7 +2648,7 @@ static sector_t raid1_sync_request(struct mddev *mddev, sector_t sector_nr,
 	/* before building a request, check if we can skip these blocks..
 	 * This call the bitmap_start_sync doesn't actually record anything
 	 */
-	if (!bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, 1) &&
+	if (!md_bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, 1) &&
 	    !conf->fullsync && !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery)) {
 		/* We can skip this block, and probably several more */
 		*skipped = 1;
@@ -2669,7 +2666,7 @@ static sector_t raid1_sync_request(struct mddev *mddev, sector_t sector_nr,
 	 * sector_nr + two times RESYNC_SECTORS
 	 */
 
-	bitmap_cond_end_sync(mddev->bitmap, sector_nr,
+	md_bitmap_cond_end_sync(mddev->bitmap, sector_nr,
 		mddev_is_clustered(mddev) && (sector_nr + 2 * RESYNC_SECTORS > conf->cluster_sync_high));
 
 
@@ -2828,8 +2825,8 @@ static sector_t raid1_sync_request(struct mddev *mddev, sector_t sector_nr,
 		if (len == 0)
 			break;
 		if (sync_blocks == 0) {
-			if (!bitmap_start_sync(mddev->bitmap, sector_nr,
+			if (!md_bitmap_start_sync(mddev->bitmap, sector_nr,
-					       &sync_blocks, still_degraded) &&
+						  &sync_blocks, still_degraded) &&
 			    !conf->fullsync &&
 			    !test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery))
 				break;
@@ -3165,7 +3162,7 @@ static int raid1_resize(struct mddev *mddev, sector_t sectors)
 	    mddev->array_sectors > newsize)
 		return -EINVAL;
 	if (mddev->bitmap) {
-		int ret = bitmap_resize(mddev->bitmap, newsize, 0, 0);
+		int ret = md_bitmap_resize(mddev->bitmap, newsize, 0, 0);
 		if (ret)
 			return ret;
 	}

drivers/md/raid10.c

@@ -440,10 +440,10 @@ static void raid10_end_read_request(struct bio *bio)
 static void close_write(struct r10bio *r10_bio)
 {
 	/* clear the bitmap if all writes complete successfully */
-	bitmap_endwrite(r10_bio->mddev->bitmap, r10_bio->sector,
+	md_bitmap_endwrite(r10_bio->mddev->bitmap, r10_bio->sector,
-			r10_bio->sectors,
+			   r10_bio->sectors,
-			!test_bit(R10BIO_Degraded, &r10_bio->state),
+			   !test_bit(R10BIO_Degraded, &r10_bio->state),
-			0);
+			   0);
 	md_write_end(r10_bio->mddev);
 }
 
@@ -917,7 +917,7 @@ static void flush_pending_writes(struct r10conf *conf)
 		blk_start_plug(&plug);
 		/* flush any pending bitmap writes to disk
 		 * before proceeding w/ I/O */
-		bitmap_unplug(conf->mddev->bitmap);
+		md_bitmap_unplug(conf->mddev->bitmap);
 		wake_up(&conf->wait_barrier);
 
 		while (bio) { /* submit pending writes */
@@ -1102,7 +1102,7 @@ static void raid10_unplug(struct blk_plug_cb *cb, bool from_schedule)
 
 	/* we aren't scheduling, so we can do the write-out directly. */
 	bio = bio_list_get(&plug->pending);
-	bitmap_unplug(mddev->bitmap);
+	md_bitmap_unplug(mddev->bitmap);
 	wake_up(&conf->wait_barrier);
 
 	while (bio) { /* submit pending writes */
@@ -1519,7 +1519,7 @@ retry_write:
 	}
 
 	atomic_set(&r10_bio->remaining, 1);
-	bitmap_startwrite(mddev->bitmap, r10_bio->sector, r10_bio->sectors, 0);
+	md_bitmap_startwrite(mddev->bitmap, r10_bio->sector, r10_bio->sectors, 0);
 
 	for (i = 0; i < conf->copies; i++) {
 		if (r10_bio->devs[i].bio)
@@ -2991,13 +2991,13 @@ static sector_t raid10_sync_request(struct mddev *mddev, sector_t sector_nr,
 
 		if (mddev->curr_resync < max_sector) { /* aborted */
 			if (test_bit(MD_RECOVERY_SYNC, &mddev->recovery))
-				bitmap_end_sync(mddev->bitmap, mddev->curr_resync,
+				md_bitmap_end_sync(mddev->bitmap, mddev->curr_resync,
-						&sync_blocks, 1);
+						   &sync_blocks, 1);
 			else for (i = 0; i < conf->geo.raid_disks; i++) {
 				sector_t sect =
 					raid10_find_virt(conf, mddev->curr_resync, i);
-				bitmap_end_sync(mddev->bitmap, sect,
+				md_bitmap_end_sync(mddev->bitmap, sect,
-						&sync_blocks, 1);
+						   &sync_blocks, 1);
 			}
 		} else {
 			/* completed sync */
@@ -3018,7 +3018,7 @@ static sector_t raid10_sync_request(struct mddev *mddev, sector_t sector_nr,
 			}
 			conf->fullsync = 0;
 		}
-		bitmap_close_sync(mddev->bitmap);
+		md_bitmap_close_sync(mddev->bitmap);
 		close_sync(conf);
 		*skipped = 1;
 		return sectors_skipped;
@@ -3112,8 +3112,8 @@ static sector_t raid10_sync_request(struct mddev *mddev, sector_t sector_nr,
 			 * we only need to recover the block if it is set in
 			 * the bitmap
 			 */
-			must_sync = bitmap_start_sync(mddev->bitmap, sect,
+			must_sync = md_bitmap_start_sync(mddev->bitmap, sect,
-						      &sync_blocks, 1);
+							 &sync_blocks, 1);
 			if (sync_blocks < max_sync)
 				max_sync = sync_blocks;
 			if (!must_sync &&
@@ -3158,8 +3158,8 @@ static sector_t raid10_sync_request(struct mddev *mddev, sector_t sector_nr,
 				}
 			}
 
-			must_sync = bitmap_start_sync(mddev->bitmap, sect,
+			must_sync = md_bitmap_start_sync(mddev->bitmap, sect,
-						      &sync_blocks, still_degraded);
+							 &sync_blocks, still_degraded);
 
 			any_working = 0;
 			for (j=0; j<conf->copies;j++) {
@@ -3335,13 +3335,12 @@ static sector_t raid10_sync_request(struct mddev *mddev, sector_t sector_nr,
 		 * safety reason, which ensures curr_resync_completed is
 		 * updated in bitmap_cond_end_sync.
 		 */
-		bitmap_cond_end_sync(mddev->bitmap, sector_nr,
+		md_bitmap_cond_end_sync(mddev->bitmap, sector_nr,
-				     mddev_is_clustered(mddev) &&
+					mddev_is_clustered(mddev) &&
-				     (sector_nr + 2 * RESYNC_SECTORS >
+					(sector_nr + 2 * RESYNC_SECTORS > conf->cluster_sync_high));
-				      conf->cluster_sync_high));
 
-		if (!bitmap_start_sync(mddev->bitmap, sector_nr,
+		if (!md_bitmap_start_sync(mddev->bitmap, sector_nr,
-				       &sync_blocks, mddev->degraded) &&
+					  &sync_blocks, mddev->degraded) &&
 		    !conf->fullsync && !test_bit(MD_RECOVERY_REQUESTED,
 						 &mddev->recovery)) {
 			/* We can skip this block */
@@ -4022,7 +4021,7 @@ static int raid10_resize(struct mddev *mddev, sector_t sectors)
 	    mddev->array_sectors > size)
 		return -EINVAL;
 	if (mddev->bitmap) {
-		int ret = bitmap_resize(mddev->bitmap, size, 0, 0);
+		int ret = md_bitmap_resize(mddev->bitmap, size, 0, 0);
 		if (ret)
 			return ret;
 	}
@@ -4287,10 +4286,9 @@ static int raid10_start_reshape(struct mddev *mddev)
 	spin_unlock_irq(&conf->device_lock);
 
 	if (mddev->delta_disks && mddev->bitmap) {
-		ret = bitmap_resize(mddev->bitmap,
+		ret = md_bitmap_resize(mddev->bitmap,
-				    raid10_size(mddev, 0,
+				       raid10_size(mddev, 0, conf->geo.raid_disks),
-						conf->geo.raid_disks),
+				       0, 0);
-				    0, 0);
 		if (ret)
 			goto abort;
 	}

drivers/md/raid5-cache.c

@@ -324,10 +324,10 @@ void r5c_handle_cached_data_endio(struct r5conf *conf,
 		if (sh->dev[i].written) {
 			set_bit(R5_UPTODATE, &sh->dev[i].flags);
 			r5c_return_dev_pending_writes(conf, &sh->dev[i]);
-			bitmap_endwrite(conf->mddev->bitmap, sh->sector,
+			md_bitmap_endwrite(conf->mddev->bitmap, sh->sector,
-					STRIPE_SECTORS,
+					   STRIPE_SECTORS,
-					!test_bit(STRIPE_DEGRADED, &sh->state),
+					   !test_bit(STRIPE_DEGRADED, &sh->state),
-					0);
+					   0);
 		}
 	}
 }

drivers/md/raid5.c

@@ -3299,8 +3299,8 @@ static int add_stripe_bio(struct stripe_head *sh, struct bio *bi, int dd_idx,
 		 */
 		set_bit(STRIPE_BITMAP_PENDING, &sh->state);
 		spin_unlock_irq(&sh->stripe_lock);
-		bitmap_startwrite(conf->mddev->bitmap, sh->sector,
+		md_bitmap_startwrite(conf->mddev->bitmap, sh->sector,
-				  STRIPE_SECTORS, 0);
+				     STRIPE_SECTORS, 0);
 		spin_lock_irq(&sh->stripe_lock);
 		clear_bit(STRIPE_BITMAP_PENDING, &sh->state);
 		if (!sh->batch_head) {
@@ -3390,8 +3390,8 @@ handle_failed_stripe(struct r5conf *conf, struct stripe_head *sh,
 			bi = nextbi;
 		}
 		if (bitmap_end)
-			bitmap_endwrite(conf->mddev->bitmap, sh->sector,
+			md_bitmap_endwrite(conf->mddev->bitmap, sh->sector,
-				STRIPE_SECTORS, 0, 0);
+					   STRIPE_SECTORS, 0, 0);
 		bitmap_end = 0;
 		/* and fail all 'written' */
 		bi = sh->dev[i].written;
@@ -3436,8 +3436,8 @@ handle_failed_stripe(struct r5conf *conf, struct stripe_head *sh,
 			}
 		}
 		if (bitmap_end)
-			bitmap_endwrite(conf->mddev->bitmap, sh->sector,
+			md_bitmap_endwrite(conf->mddev->bitmap, sh->sector,
-					STRIPE_SECTORS, 0, 0);
+					   STRIPE_SECTORS, 0, 0);
 		/* If we were in the middle of a write the parity block might
 		 * still be locked - so just clear all R5_LOCKED flags
 		 */
@@ -3777,10 +3777,10 @@ returnbi:
 					bio_endio(wbi);
 					wbi = wbi2;
 				}
-				bitmap_endwrite(conf->mddev->bitmap, sh->sector,
+				md_bitmap_endwrite(conf->mddev->bitmap, sh->sector,
-						STRIPE_SECTORS,
+						   STRIPE_SECTORS,
-					 !test_bit(STRIPE_DEGRADED, &sh->state),
+						   !test_bit(STRIPE_DEGRADED, &sh->state),
-						0);
+						   0);
 				if (head_sh->batch_head) {
 					sh = list_first_entry(&sh->batch_list,
 							      struct stripe_head,
@@ -5543,10 +5543,10 @@ static void make_discard_request(struct mddev *mddev, struct bio *bi)
 			for (d = 0;
 			     d < conf->raid_disks - conf->max_degraded;
 			     d++)
-				bitmap_startwrite(mddev->bitmap,
+				md_bitmap_startwrite(mddev->bitmap,
-						  sh->sector,
+						     sh->sector,
-						  STRIPE_SECTORS,
+						     STRIPE_SECTORS,
-						  0);
+						     0);
 			sh->bm_seq = conf->seq_flush + 1;
 			set_bit(STRIPE_BIT_DELAY, &sh->state);
 		}
@@ -6024,11 +6024,11 @@ static inline sector_t raid5_sync_request(struct mddev *mddev, sector_t sector_n
 		}
 
 		if (mddev->curr_resync < max_sector) /* aborted */
-			bitmap_end_sync(mddev->bitmap, mddev->curr_resync,
+			md_bitmap_end_sync(mddev->bitmap, mddev->curr_resync,
-					&sync_blocks, 1);
+					   &sync_blocks, 1);
 		else /* completed sync */
 			conf->fullsync = 0;
-		bitmap_close_sync(mddev->bitmap);
+		md_bitmap_close_sync(mddev->bitmap);
 
 		return 0;
 	}
@@ -6057,7 +6057,7 @@ static inline sector_t raid5_sync_request(struct mddev *mddev, sector_t sector_n
 	}
 	if (!test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery) &&
 	    !conf->fullsync &&
-	    !bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, 1) &&
+	    !md_bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, 1) &&
 	    sync_blocks >= STRIPE_SECTORS) {
 		/* we can skip this block, and probably more */
 		sync_blocks /= STRIPE_SECTORS;
@@ -6065,7 +6065,7 @@ static inline sector_t raid5_sync_request(struct mddev *mddev, sector_t sector_n
 		return sync_blocks * STRIPE_SECTORS; /* keep things rounded to whole stripes */
 	}
 
-	bitmap_cond_end_sync(mddev->bitmap, sector_nr, false);
+	md_bitmap_cond_end_sync(mddev->bitmap, sector_nr, false);
 
 	sh = raid5_get_active_stripe(conf, sector_nr, 0, 1, 0);
 	if (sh == NULL) {
@@ -6088,7 +6088,7 @@ static inline sector_t raid5_sync_request(struct mddev *mddev, sector_t sector_n
 	}
 	rcu_read_unlock();
 
-	bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, still_degraded);
+	md_bitmap_start_sync(mddev->bitmap, sector_nr, &sync_blocks, still_degraded);
 
 	set_bit(STRIPE_SYNC_REQUESTED, &sh->state);
 	set_bit(STRIPE_HANDLE, &sh->state);
@@ -6289,7 +6289,7 @@ static void raid5d(struct md_thread *thread)
 			/* Now is a good time to flush some bitmap updates */
 			conf->seq_flush++;
 			spin_unlock_irq(&conf->device_lock);
-			bitmap_unplug(mddev->bitmap);
+			md_bitmap_unplug(mddev->bitmap);
 			spin_lock_irq(&conf->device_lock);
 			conf->seq_write = conf->seq_flush;
 			activate_bit_delay(conf, conf->temp_inactive_list);
@@ -7745,7 +7745,7 @@ static int raid5_resize(struct mddev *mddev, sector_t sectors)
 	    mddev->array_sectors > newsize)
 		return -EINVAL;
 	if (mddev->bitmap) {
-		int ret = bitmap_resize(mddev->bitmap, sectors, 0, 0);
+		int ret = md_bitmap_resize(mddev->bitmap, sectors, 0, 0);
 		if (ret)
 			return ret;
 	}

include/linux/bitmap.h

@@ -104,6 +104,14 @@
  * contain all bit positions from 0 to 'bits' - 1.
  */
 
+/*
+ * Allocation and deallocation of bitmap.
+ * Provided in lib/bitmap.c to avoid circular dependency.
+ */
+extern unsigned long *bitmap_alloc(unsigned int nbits, gfp_t flags);
+extern unsigned long *bitmap_zalloc(unsigned int nbits, gfp_t flags);
+extern void bitmap_free(const unsigned long *bitmap);
+
 /*
  * lib/bitmap.c provides these functions:
  */

include/linux/gpio_keys.h

@@ -2,6 +2,8 @@
 #ifndef _GPIO_KEYS_H
 #define _GPIO_KEYS_H
 
+#include <linux/types.h>
+
 struct device;
 
 /**

include/linux/joystick.h

@@ -17,10 +17,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- * 
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@suse.cz>, or by paper mail:
- * Vojtech Pavlik, Ucitelska 1576, Prague 8, 182 00 Czech Republic
  */
 #ifndef _LINUX_JOYSTICK_H
 #define _LINUX_JOYSTICK_H

include/uapi/linux/joystick.h

@@ -18,10 +18,6 @@
  * You should have received a copy of the GNU General Public License
  * along with this program; if not, write to the Free Software
  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- * 
- * Should you need to contact me, the author, you can do so either by
- * e-mail - mail your message to <vojtech@suse.cz>, or by paper mail:
- * Vojtech Pavlik, Ucitelska 1576, Prague 8, 182 00 Czech Republic
  */
 #ifndef _UAPI_LINUX_JOYSTICK_H
 #define _UAPI_LINUX_JOYSTICK_H

include/xen/interface/io/displif.h

@@ -189,6 +189,13 @@
  *
  *----------------------------- Connector settings ----------------------------
  *
+ * unique-id
+ *      Values:         <string>
+ *
+ *      After device instance initialization each connector is assigned a
+ *      unique ID, so it can be identified by the backend by this ID.
+ *      This can be UUID or such.
+ *
  * resolution
  *      Values:         <width, uint32_t>x<height, uint32_t>
  *
@@ -368,6 +375,7 @@
 #define XENDISPL_FIELD_EVT_CHANNEL	"evt-event-channel"
 #define XENDISPL_FIELD_RESOLUTION	"resolution"
 #define XENDISPL_FIELD_BE_ALLOC		"be-alloc"
+#define XENDISPL_FIELD_UNIQUE_ID	"unique-id"
 
 /*
  ******************************************************************************

include/xen/interface/io/kbdif.h

@@ -51,6 +51,18 @@
  * corresponding entries in XenStore and puts 1 as the value of the entry.
  * If a feature is not supported then 0 must be set or feature entry omitted.
  *
+ * feature-disable-keyboard
+ *      Values:         <uint>
+ *
+ *      If there is no need to expose a virtual keyboard device by the
+ *      frontend then this must be set to 1.
+ *
+ * feature-disable-pointer
+ *      Values:         <uint>
+ *
+ *      If there is no need to expose a virtual pointer device by the
+ *      frontend then this must be set to 1.
+ *
  * feature-abs-pointer
  *      Values:         <uint>
  *
@@ -63,6 +75,22 @@
  *      Backends, which support reporting of multi-touch events
  *      should set this to 1.
  *
+ * feature-raw-pointer
+ *      Values:        <uint>
+ *
+ *      Backends, which support reporting raw (unscaled) absolute coordinates
+ *      for pointer devices should set this to 1. Raw (unscaled) values have
+ *      a range of [0, 0x7fff].
+ *
+ *-----------------------  Device Instance Parameters ------------------------
+ *
+ * unique-id
+ *      Values:         <string>
+ *
+ *      After device instance initialization it is assigned a unique ID,
+ *      so every instance of the frontend can be identified by the backend
+ *      by this ID. This can be UUID or such.
+ *
  *------------------------- Pointer Device Parameters ------------------------
  *
  * width
@@ -77,6 +105,25 @@
  *      Maximum Y coordinate (height) to be used by the frontend
  *      while reporting input events, pixels, [0; UINT32_MAX].
  *
+ *----------------------- Multi-touch Device Parameters ----------------------
+ *
+ * multi-touch-num-contacts
+ *      Values:         <uint>
+ *
+ *      Number of simultaneous touches reported.
+ *
+ * multi-touch-width
+ *      Values:         <uint>
+ *
+ *      Width of the touch area to be used by the frontend
+ *      while reporting input events, pixels, [0; UINT32_MAX].
+ *
+ * multi-touch-height
+ *      Values:         <uint>
+ *
+ *      Height of the touch area to be used by the frontend
+ *      while reporting input events, pixels, [0; UINT32_MAX].
+ *
  *****************************************************************************
  *                            Frontend XenBus Nodes
  *****************************************************************************
@@ -98,6 +145,13 @@
  *
  *      Request backend to report multi-touch events.
  *
+ * request-raw-pointer
+ *      Values:         <uint>
+ *
+ *      Request backend to report raw unscaled absolute pointer coordinates.
+ *      This option is only valid if request-abs-pointer is also set.
+ *      Raw unscaled coordinates have the range [0, 0x7fff]
+ *
  *----------------------- Request Transport Parameters -----------------------
  *
  * event-channel
@@ -117,25 +171,6 @@
  *
  *      OBSOLETE, not recommended for use.
  *      PFN of the shared page.
- *
- *----------------------- Multi-touch Device Parameters -----------------------
- *
- * multi-touch-num-contacts
- *      Values:         <uint>
- *
- *      Number of simultaneous touches reported.
- *
- * multi-touch-width
- *      Values:         <uint>
- *
- *      Width of the touch area to be used by the frontend
- *      while reporting input events, pixels, [0; UINT32_MAX].
- *
- * multi-touch-height
- *      Values:         <uint>
- *
- *      Height of the touch area to be used by the frontend
- *      while reporting input events, pixels, [0; UINT32_MAX].
  */
 
 /*
@@ -163,9 +198,13 @@
 
 #define XENKBD_DRIVER_NAME		"vkbd"
 
+#define XENKBD_FIELD_FEAT_DSBL_KEYBRD	"feature-disable-keyboard"
+#define XENKBD_FIELD_FEAT_DSBL_POINTER	"feature-disable-pointer"
 #define XENKBD_FIELD_FEAT_ABS_POINTER	"feature-abs-pointer"
+#define XENKBD_FIELD_FEAT_RAW_POINTER	"feature-raw-pointer"
 #define XENKBD_FIELD_FEAT_MTOUCH	"feature-multi-touch"
 #define XENKBD_FIELD_REQ_ABS_POINTER	"request-abs-pointer"
+#define XENKBD_FIELD_REQ_RAW_POINTER	"request-raw-pointer"
 #define XENKBD_FIELD_REQ_MTOUCH		"request-multi-touch"
 #define XENKBD_FIELD_RING_GREF		"page-gref"
 #define XENKBD_FIELD_EVT_CHANNEL	"event-channel"
@@ -174,6 +213,7 @@
 #define XENKBD_FIELD_MT_WIDTH		"multi-touch-width"
 #define XENKBD_FIELD_MT_HEIGHT		"multi-touch-height"
 #define XENKBD_FIELD_MT_NUM_CONTACTS	"multi-touch-num-contacts"
+#define XENKBD_FIELD_UNIQUE_ID		"unique-id"
 
 /* OBSOLETE, not recommended for use */
 #define XENKBD_FIELD_RING_REF		"page-ref"

include/xen/interface/io/sndif.h

@@ -278,13 +278,11 @@
  *      defined under the same device.
  *
  * unique-id
- *      Values:         <uint32_t>
+ *      Values:         <string>
  *
- *      After stream initialization it is assigned a unique ID (within the front
+ *      After stream initialization it is assigned a unique ID, so every
- *      driver), so every stream of the frontend can be identified by the
+ *      stream of the frontend can be identified by the backend by this ID.
- *      backend by this ID. This is not equal to stream-idx as the later is
+ *      This can be UUID or such.
- *      zero based within the device, but this index is contigous within the
- *      driver.
  *
  *-------------------- Stream Request Transport Parameters --------------------
  *

lib/bitmap.c

@@ -13,6 +13,7 @@
 #include <linux/bitops.h>
 #include <linux/bug.h>
 #include <linux/kernel.h>
+#include <linux/slab.h>
 #include <linux/string.h>
 #include <linux/uaccess.h>
 
@@ -1125,6 +1126,25 @@ void bitmap_copy_le(unsigned long *dst, const unsigned long *src, unsigned int n
 EXPORT_SYMBOL(bitmap_copy_le);
 #endif
 
+unsigned long *bitmap_alloc(unsigned int nbits, gfp_t flags)
+{
+	return kmalloc_array(BITS_TO_LONGS(nbits), sizeof(unsigned long),
+			     flags);
+}
+EXPORT_SYMBOL(bitmap_alloc);
+
+unsigned long *bitmap_zalloc(unsigned int nbits, gfp_t flags)
+{
+	return bitmap_alloc(nbits, flags | __GFP_ZERO);
+}
+EXPORT_SYMBOL(bitmap_zalloc);
+
+void bitmap_free(const unsigned long *bitmap)
+{
+	kfree(bitmap);
+}
+EXPORT_SYMBOL(bitmap_free);
+
 #if BITS_PER_LONG == 64
 /**
  * bitmap_from_arr32 - copy the contents of u32 array of bits to bitmap