ARM: dts: imx6q: Add Variscite DART-MX6 Carrier-board support
This patch adds support for the i.MX6 Quad variant of the Variscite DART-MX6 SoM Carrier-Board. This Carrier-Board has the following : - LVDS interface for the VLCD-CAP-GLD-LVDS 7" LCD 800 x 480 touch display - HDMI Connector - USB Host + USB OTG Connector - 10/100/1000 Mbps Ethernet - miniPCI-Express slot - SD Card connector - Audio Headphone/Line In jack connectors - On-board DMIC - CAN bus header - SPI header - Camera Interfaces header - 4xButtons, 2xLeds - OnBoard RTC with Coin Backup battery socket - RS232 Header + USB-Serial debug port Product Page : http://www.variscite.com/products/evaluation-kits/dart-mx6-kits The board support is done with all on-board and header interfaces enabled. 7" LVDS Touchscreen is enabled by default along HDMI output. Audio interface is supported with the "simple-card" bindings. PCIe slot, On-Board DMIC and Camera Interfaces are not handled yet. Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>hifive-unleashed-5.1
Neil Armstrong
Shawn Guo
parent
c95e75852d
commit
26b7784b29
|
|
@ -478,6 +478,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
|||
imx6q-tx6q-11x0-mb7.dtb \
|
||||
imx6q-udoo.dtb \
|
||||
imx6q-utilite-pro.dtb \
|
||||
imx6q-var-dt6customboard.dtb \
|
||||
imx6q-wandboard.dtb \
|
||||
imx6q-wandboard-revb1.dtb \
|
||||
imx6q-wandboard-revd1.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,235 @@
|
|||
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
||||
/*
|
||||
* Support for Variscite DART-MX6 Carrier-board
|
||||
*
|
||||
* Copyright 2017 BayLibre, SAS
|
||||
* Author: Neil Armstrong <narmstrong@baylibre.com>
|
||||
*/
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "imx6q.dtsi"
|
||||
#include "imx6qdl-var-dart.dtsi"
|
||||
#include <dt-bindings/input/linux-event-codes.h>
|
||||
|
||||
/ {
|
||||
model = "Variscite DART-MX6 Carrier-board";
|
||||
compatible = "variscite,dt6customboard", "fsl,imx6q";
|
||||
|
||||
backlight_lvds: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm2 0 50000>;
|
||||
brightness-levels = <0 4 8 16 32 64 128 248>;
|
||||
default-brightness-level = <7>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
autorepeat;
|
||||
|
||||
back {
|
||||
gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_BACK>;
|
||||
label = "Key Back";
|
||||
linux,input-type = <1>;
|
||||
debounce-interval = <100>;
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
home {
|
||||
gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_HOME>;
|
||||
label = "Key Home";
|
||||
linux,input-type = <1>;
|
||||
debounce-interval = <100>;
|
||||
wakeup-source;
|
||||
};
|
||||
|
||||
menu {
|
||||
gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_MENU>;
|
||||
label = "Key Menu";
|
||||
linux,input-type = <1>;
|
||||
debounce-interval = <100>;
|
||||
wakeup-source;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led1 {
|
||||
gpios = <&gpio4 27 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "heartbeat";
|
||||
};
|
||||
|
||||
led2 {
|
||||
gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
|
||||
linux,default-trigger = "default-on";
|
||||
};
|
||||
};
|
||||
|
||||
panel1: lvds-panel {
|
||||
compatible = "sgd,gktw70sdae4se", "panel-lvds";
|
||||
backlight = <&backlight_lvds>;
|
||||
width-mm = <153>;
|
||||
height-mm = <86>;
|
||||
label = "gktw70sdae4se";
|
||||
data-mapping = "jeida-18";
|
||||
|
||||
panel-timing {
|
||||
clock-frequency = <32000000>;
|
||||
hactive = <800>;
|
||||
vactive = <480>;
|
||||
hback-porch = <39>;
|
||||
hfront-porch = <39>;
|
||||
vback-porch = <29>;
|
||||
vfront-porch = <13>;
|
||||
hsync-len = <47>;
|
||||
vsync-len = <2>;
|
||||
};
|
||||
|
||||
port {
|
||||
panel_in: endpoint {
|
||||
remote-endpoint = <&lvds1_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
reg_usb_h1_vbus: regulator-usbh1vbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb_h1_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
reg_usb_otg_vbus: regulator-usbotgvbus {
|
||||
compatible = "regulator-fixed";
|
||||
regulator-name = "usb_otg_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
sound {
|
||||
compatible = "simple-audio-card";
|
||||
simple-audio-card,name = "dt6-customboard-audio";
|
||||
simple-audio-card,format = "i2s";
|
||||
simple-audio-card,bitclock-master = <&sound_codec>;
|
||||
simple-audio-card,frame-master = <&sound_codec>;
|
||||
simple-audio-card,widgets = "Headphone", "Headphone Jack",
|
||||
"Line", "Line In";
|
||||
simple-audio-card,routing = "Headphone Jack", "HPLOUT",
|
||||
"Headphone Jack", "HPROUT",
|
||||
"LINE1L", "Line In",
|
||||
"LINE1R", "Line In";
|
||||
|
||||
sound_cpu: simple-audio-card,cpu {
|
||||
sound-dai = <&ssi2>;
|
||||
};
|
||||
|
||||
sound_codec: simple-audio-card,codec {
|
||||
sound-dai = <&tlv320aic3106>;
|
||||
clocks = <&clks IMX6QDL_CLK_CKO>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&can1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&ecspi1 {
|
||||
cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>,
|
||||
<&gpio4 10 GPIO_ACTIVE_HIGH>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&fec {
|
||||
status = "okay";
|
||||
phy-mode = "rgmii";
|
||||
phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c1 {
|
||||
clock-frequency = <100000>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
clock-frequency = <100000>;
|
||||
status = "okay";
|
||||
|
||||
touchscreen@38 {
|
||||
compatible = "edt,edt-ft5x06";
|
||||
reg = <0x38>;
|
||||
interrupt-parent = <&gpio1>;
|
||||
interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
|
||||
touchscreen-size-x = <800>;
|
||||
touchscreen-size-y = <480>;
|
||||
touchscreen-inverted-x;
|
||||
touchscreen-inverted-y;
|
||||
};
|
||||
|
||||
rtc@68 {
|
||||
compatible = "isil,isl12057";
|
||||
reg = <0x68>;
|
||||
};
|
||||
};
|
||||
|
||||
&ldb {
|
||||
status = "okay";
|
||||
|
||||
lvds-channel@1 {
|
||||
status = "okay";
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
|
||||
lvds1_out: endpoint {
|
||||
remote-endpoint = <&panel_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pwm2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh1 {
|
||||
vbus-supply = <®_usb_h1_vbus>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbotg {
|
||||
vbus-supply = <®_usb_otg_vbus>;
|
||||
dr_mode = "otg";
|
||||
srp-disable;
|
||||
hnp-disable;
|
||||
adp-disable;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usdhc2 {
|
||||
cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
|
||||
status = "okay";
|
||||
};
|
||||
Loading…
Reference in New Issue