redonkable
/
alistair23-linux
1
0
Fork 0
Code Releases Activity

Allwinner DT changes for 4.11 

The usual chunk of DT changes, most notably:
   - Support for the H2+ and the V3s
   - CPUFreq support for the A33
   - SPDIF support for the A31 and H3
   - New boards: Beelink X2, Lichee Pi One, Lichee Pi Zero,
     Orange Pi Zero
 -----BEGIN PGP SIGNATURE-----
 
 iQIcBAABCAAGBQJYkFCYAAoJEBx+YmzsjxAgljYP/0seq1LEtMtoTeXHP6ZPkrju
 7/pHjEwJFZRH98DZ0QMAcUM+fHB0C4h5UadEXCIyzYBO9yeHzm+Hoys4VvpaQasL
 6taHz3zJ5T1/si7HyyP16LEwaFeARmSO3aXh4t5195Y2u3BFD+b2i5BpMquCC5CM
 XXJmx3Q487bUWjdufUqiSz0gWK1BfKw/eJAawoJbIl9Z6v7wOvE0SQF8ZtIc2eOl
 WX9uyNKdYh4PsSC0TxexDeKHNhLh2hJgO1HxYg+DTdyGM144XO0OSuPFtfilROaL
 tViKBohffz8A4K5m5iCaDva+P9318iO2xVN91/DFV6VS2XhMRvUrfZRd9kEvuhvu
 FJF3KrIZDLRu7tkcHVt9GDjO3CElejMT+qLOGg7t+9nJ+6RjyHUSBs6HIU0Opsu0
 Fw7LyHihzDH/m7m87lxUUmC5rSRqMVfuiKwphHYqDzkYEGEnL4kv055rE6cBFGyM
 zr7aajpiFgARPXj1XdZQRnz8uC8kySUf2o1oLPdhP3szX41AWBTiBuT7yqMB6qnD
 5B8Xj4zTsjEYfwsaWaI8VhbK2UsLgsUlbUXugKfqtjoPTjaWN6zQ3C6030Bov9za
 2jo0+187iYp/B/M4DPiH3Kicfntnj4DWRmBt8wCX/PVXS2tD1S617JzugbX/+EZK
 PF328UgsT3c1UkccBK9/
 =ig5Q
 -----END PGP SIGNATURE-----

Merge tag 'sunxi-dt-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Pull "Allwinner DT changes for 4.11" from Maxime Ripard:

The usual chunk of DT changes, most notably:
  - Support for the H2+ and the V3s
  - CPUFreq support for the A33
  - SPDIF support for the A31 and H3
  - New boards: Beelink X2, Lichee Pi One, Lichee Pi Zero,
    Orange Pi Zero

* tag 'sunxi-dt-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (42 commits)
  ARM: dts: sun8i-h3: Add SPDIF to the Beelink X2
  ARM: dts: sun8i-h3: Add the SPDIF block to the H3
  ARM: dts: sun8i-h3: Add SPDIF TX pin to the H3
  ARM: dts: sun8i-h3: Add dts for the Beelink X2 STB
  ARM: sun8i: sina33: Enable display
  ARM: sun8i: a23/a33: Add the oscillators accuracy
  ARM: sun8i: a23/a33: Enable the real LOSC and use it
  ARM: dts: sunxi: add support for Lichee Pi Zero board
  ARM: dts: sunxi: add dtsi file for V3s SoC
  ARM: dts: sun6i: sina31s: Enable USB OTG controller in peripheral mode
  ARM: dts: sun8i: reference-design: use AXP223 DTSI
  ARM: dts: sun8i: parrot: use AXP223 DTSI
  ARM: dts: sun8i: sina33: use AXP223 DTSI
  ARM: dts: sun8i: a33-olinuxino: use AXP223 DTSI
  ARM: dts: add DTSI for AXP223
  dt-bindings: power: axp20x-usb: add axp223 compatible
  ARM: dts: sun7i: Add wifi dt node on Banana Pro
  ARM: dts: sun6i: Add SPDIF to the Mele I7
  devicetree: bindings: Add vendor prefix for Shenzhen Xunlong Software
  ARM: dts: sun8i-h3: orange-pi-pc: Enable audio codec
  ...
hifive-unleashed-5.1
Arnd Bergmann 2017-02-07 16:08:58 +01:00
parent fd896f5acd ef09e0f539
commit 2bad7f862e
32 changed files with 1436 additions and 71 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

5
Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt
View File

@ -3,6 +3,11 @@ AXP20x USB power supply
Required Properties:
-compatible: One of: "x-powers,axp202-usb-power-supply"
"x-powers,axp221-usb-power-supply"
"x-powers,axp223-usb-power-supply"
The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight
variations such as the former being able to set the VBUS power supply max
current to 100mA, unlike the latter.
This node is a subnode of the axp20x PMIC.

2
Documentation/devicetree/bindings/vendor-prefixes.txt
View File

@ -162,6 +162,7 @@ lantiq Lantiq Semiconductor
lego LEGO Systems A/S
lenovo Lenovo Group Ltd.
lg LG Corporation
licheepi Lichee Pi
linux Linux-specific binding
lltc Linear Technology Corporation
lsi LSI Corp. (LSI Logic)
@ -331,6 +332,7 @@ x-powers X-Powers
xes Extreme Engineering Solutions (X-ES)
xillybus Xillybus Ltd.
xlnx Xilinx
xunlong Shenzhen Xunlong Software CO.,Limited
zarlink Zarlink Semiconductor
zii Zodiac Inflight Innovations
zte ZTE Corp.

6
arch/arm/boot/dts/Makefile
View File

@ -798,6 +798,7 @@ dtb-$(CONFIG_MACH_SUN5I) += \
sun5i-a13-empire-electronix-m712.dtb \
sun5i-a13-hsg-h702.dtb \
sun5i-a13-inet-98v-rev2.dtb \
sun5i-a13-licheepi-one.dtb \
sun5i-a13-olinuxino.dtb \
sun5i-a13-olinuxino-micro.dtb \
sun5i-a13-q8-tablet.dtb \
@ -861,7 +862,9 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-a33-sinlinx-sina33.dtb \
sun8i-a83t-allwinner-h8homlet-v2.dtb \
sun8i-a83t-cubietruck-plus.dtb \
sun8i-h2-plus-orangepi-zero.dtb \
sun8i-h3-bananapi-m2-plus.dtb \
sun8i-h3-beelink-x2.dtb \
sun8i-h3-nanopi-neo.dtb \
sun8i-h3-orangepi-2.dtb \
sun8i-h3-orangepi-lite.dtb \
@ -870,7 +873,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-pc-plus.dtb \
sun8i-h3-orangepi-plus.dtb \
sun8i-h3-orangepi-plus2e.dtb \
sun8i-r16-parrot.dtb
sun8i-r16-parrot.dtb \
sun8i-v3s-licheepi-zero.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb

58
arch/arm/boot/dts/axp223.dtsi 100644
View File

@ -0,0 +1,58 @@
/*
* Copyright 2016 Free Electrons
*
* Quentin Schulz <quentin.schulz@free-electrons.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/*
* AXP223 Integrated Power Management Chip
* http://www.x-powers.com/product/AXP22X.php
* http://dl.linux-sunxi.org/AXP/AXP223-en.pdf
*
* The AXP223 shares most of its logic with the AXP221 but it has some
* differences, for the VBUS driver for example.
*/
#include "axp22x.dtsi"
&usb_power_supply {
compatible = "x-powers,axp223-usb-power-supply";
};

31
arch/arm/boot/dts/sun4i-a10-a1000.dts
View File

@ -117,6 +117,10 @@
status = "okay";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&ehci0 {
status = "okay";
};
@ -196,6 +200,33 @@
};
};
#include "axp209.dtsi"
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1250000>;
regulator-name = "vdd-int-dll";
};
&reg_ldo1 {
regulator-name = "vdd-rtc";
};
&reg_ldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
&reg_usb1_vbus {
status = "okay";
};

1
arch/arm/boot/dts/sun4i-a10.dtsi
View File

@ -1023,6 +1023,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {

224
arch/arm/boot/dts/sun5i-a13-licheepi-one.dts 100644
View File

@ -0,0 +1,224 @@
/*
* Copyright 2016 Icenowy Zheng <icenowy@aosc.xyz>
*
* Based on sun5i-a13-olinuxino.dts, which is
* Copyright 2012 Maxime Ripard <maxime.ripard@free-electrons.com>
* Copyright 2013 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun5i-a13.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Lichee Pi One";
compatible = "licheepi,licheepi-one", "allwinner,sun5i-a13";
aliases {
serial0 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
red {
label ="licheepi:red:usr";
gpios = <&pio 2 5 GPIO_ACTIVE_LOW>;
};
green {
label ="licheepi:green:usr";
gpios = <&pio 2 19 GPIO_ACTIVE_LOW>;
default-state = "on";
};
blue {
label ="licheepi:blue:usr";
gpios = <&pio 2 4 GPIO_ACTIVE_LOW>;
};
};
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&ehci0 {
status = "okay";
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupts = <0>;
interrupt-controller;
#interrupt-cells = <1>;
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "disabled";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "disabled";
};
&lradc {
vref-supply = <&reg_ldo2>;
status = "okay";
button@984 {
label = "Home";
linux,code = <KEY_HOMEPAGE>;
channel = <0>;
voltage = <984126>;
};
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
broken-cd;
status = "okay";
};
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_4bit_pins_a>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
broken-cd;
status = "okay";
};
&ohci0 {
status = "okay";
};
&otg_sram {
status = "okay";
};
#include "axp209.dtsi"
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-int-dll";
};
&reg_ldo1 {
regulator-name = "vdd-rtc";
};
&reg_ldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
&reg_ldo3 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "csi-1.8v";
};
&reg_ldo4 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "csi-2.8v";
};
&reg_usb0_vbus {
gpio = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_b>;
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
pinctrl-names = "default";
usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
usb0_vbus-supply = <&reg_usb0_vbus>;
usb1_vbus-supply = <&reg_vcc5v0>;
status = "okay";
};

9
arch/arm/boot/dts/sun5i.dtsi
View File

@ -582,6 +582,7 @@
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc2_pins_a: mmc2@0 {
@ -593,6 +594,14 @@
bias-pull-up;
};
mmc2_4bit_pins_a: mmc2-4bit@0 {
pins = "PC6", "PC7", "PC8", "PC9",
"PC10", "PC11";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
spi2_pins_a: spi2@0 {
pins = "PE1", "PE2", "PE3";
function = "spi2";

19
arch/arm/boot/dts/sun6i-a31-hummingbird.dts
View File

@ -244,6 +244,7 @@
reg = <0x68>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
x-powers,drive-vbus-en;
};
};
@ -302,6 +303,11 @@
regulator-name = "vcc-dram";
};
&reg_drivevbus {
regulator-name = "usb0-vbus";
status = "okay";
};
&reg_usb1_vbus {
gpio = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */
status = "okay";
@ -326,12 +332,25 @@
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usb1_vbus_pin_a {
/* different pin from sunxi-common-regulators */
pins = "PH24";
};
&usbphy {
usb0_id_det-gpio = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
usb0_vbus_det-gpio = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_drivevbus>;
usb1_vbus-supply = <&reg_usb1_vbus>;
status = "okay";
};

30
arch/arm/boot/dts/sun6i-a31-i7.dts
View File

@ -69,6 +69,29 @@
gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>;
};
};
sound {
compatible = "simple-audio-card";
simple-audio-card,name = "On-board SPDIF";
simple-audio-card,cpu {
sound-dai = <&spdif>;
};
simple-audio-card,codec {
sound-dai = <&spdif_out>;
};
};
spdif_out: spdif-out {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
};
&codec {
allwinner,audio-routing =
"Headphone", "HP";
status = "okay";
};
&ehci0 {
@ -132,6 +155,13 @@
status = "okay";
};
&spdif {
pinctrl-names = "default";
pinctrl-0 = <&spdif_pins_a>;
spdif-out = "okay";
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;

22
arch/arm/boot/dts/sun6i-a31.dtsi
View File

@ -547,6 +547,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc1_pins_a: mmc1@0 {
@ -554,6 +555,7 @@
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_pins_a: mmc2@0 {
@ -571,6 +573,7 @@
"PC24";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
mmc3_8bit_emmc_pins: mmc3@1 {
@ -580,6 +583,12 @@
"PC24";
function = "mmc3";
drive-strength = <40>;
bias-pull-up;
};
spdif_pins_a: spdif@0 {
pins = "PH28";
function = "spdif";
};
uart0_pins_a: uart0@0 {
@ -604,6 +613,19 @@
reg = <0x01c20ca0 0x20>;
};
spdif: spdif@01c21000 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun6i-a31-spdif";
reg = <0x01c21000 0x400>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_APB1_SPDIF>, <&ccu CLK_SPDIF>;
resets = <&ccu RST_APB1_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma 2>, <&dma 2>;
dma-names = "rx", "tx";
status = "disabled";
};
lradc: lradc@01c22800 {
compatible = "allwinner,sun4i-a10-lradc-keys";
reg = <0x01c22800 0x100>;

5
arch/arm/boot/dts/sun6i-a31s-sina31s.dts
View File

@ -153,6 +153,11 @@
regulator-name = "vcc-gmac-phy";
};
&usb_otg {
dr_mode = "peripheral";
status = "okay";
};
&usbphy {
status = "okay";
};

33
arch/arm/boot/dts/sun7i-a20-bananapro.dts
View File

@ -76,6 +76,13 @@
};
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
pinctrl-0 = <&vmmc3_pin_bananapro>;
reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>;
};
reg_gmac_3v3: gmac-3v3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
@ -87,23 +94,16 @@
enable-active-high;
gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
};
reg_vmmc3: vmmc3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&vmmc3_pin_bananapro>;
regulator-name = "vmmc3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
enable-active-high;
gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
};
};
&ahci {
status = "okay";
};
&codec {
status = "okay";
};
&ehci0 {
status = "okay";
};
@ -166,10 +166,19 @@
&mmc3 {
pinctrl-names = "default";
pinctrl-0 = <&mmc3_pins_a>;
vmmc-supply = <&reg_vmmc3>;
vmmc-supply = <&reg_vcc3v3>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
brcmf: bcrmf@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
interrupt-parent = <&pio>;
interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
interrupt-names = "host-wake";
};
};
&ohci0 {

38
arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts
View File

@ -120,6 +120,18 @@
};
};
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins_a>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins_a>;
status = "okay";
};
&lradc {
vref-supply = <&reg_vcc3v0>;
status = "okay";
@ -280,12 +292,38 @@
status = "okay";
};
&spi1 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins_a>,
<&spi1_cs0_pins_a>;
status = "okay";
};
&spi2 {
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>,
<&spi2_cs0_pins_a>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&uart6 {
pinctrl-names = "default";
pinctrl-0 = <&uart6_pins_a>;
status = "okay";
};
&uart7 {
pinctrl-names = "default";
pinctrl-0 = <&uart7_pins_a>;
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";

90
arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
View File

@ -112,57 +112,9 @@
status = "okay";
axp209: pmic@34 {
compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <1>;
acin-supply = <&reg_axp_ipsout>;
vin2-supply = <&reg_axp_ipsout>;
vin3-supply = <&reg_axp_ipsout>;
ldo24in-supply = <&reg_axp_ipsout>;
ldo3in-supply = <&reg_axp_ipsout>;
regulators {
vdd_rtc: ldo1 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
};
avcc: ldo2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vcc_csi0: ldo3 {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <3500000>;
regulator-always-on;
};
vcc_csi1: ldo4 {
regulator-min-microvolt = <1250000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdd_cpu: dcdc2 {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <2275000>;
regulator-always-on;
};
vdd_int: dcdc3 {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <3500000>;
regulator-always-on;
};
};
};
};
@ -236,6 +188,48 @@
status = "okay";
};
#include "axp209.dtsi"
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-int-dll";
};
&reg_ldo1 {
regulator-always-on;
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1300000>;
regulator-name = "vdd-rtc";
};
&reg_ldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
&reg_ldo3 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "vddio-csi0";
};
&reg_ldo4 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "vddio-csi1";
};
&reg_usb0_vbus {
pinctrl-0 = <&usb0_vbus_pin_lime2>;
gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;

6
arch/arm/boot/dts/sun7i-a20.dtsi
View File

@ -871,6 +871,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
num-cs = <4>;
};
spi1: spi@01c06000 {
@ -885,6 +886,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
num-cs = <1>;
};
emac: ethernet@01c0b000 {
@ -1037,6 +1039,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
num-cs = <1>;
};
ahci: sata@01c18000 {
@ -1079,6 +1082,7 @@
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
num-cs = <1>;
};
pio: pinctrl@01c20800 {
@ -1179,6 +1183,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin_reference_design: mmc0_cd_pin@0 {
@ -1200,6 +1205,7 @@
"PI7", "PI8", "PI9";
function = "mmc3";
drive-strength = <30>;
bias-pull-up;
};
ps20_pins_a: ps20@0 {

24
arch/arm/boot/dts/sun8i-a23-a33.dtsi
View File

@ -84,7 +84,7 @@
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
@ -106,14 +106,16 @@
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-accuracy = <50000>;
clock-output-names = "osc24M";
};
osc32k: osc32k_clk {
ext_osc32k: ext_osc32k_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
clock-accuracy = <50000>;
clock-output-names = "ext-osc32k";
};
};
@ -256,7 +258,7 @@
ccu: clock@01c20000 {
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clocks = <&osc24M>, <&rtc 0>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
@ -266,7 +268,7 @@
/* compatible gets set in SoC specific dtsi file */
reg = <0x01c20800 0x400>;
/* interrupts get set in SoC specific dtsi file */
clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
@ -293,6 +295,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc1_pins_a: mmc1@0 {
@ -300,6 +303,7 @@
"PG3", "PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
@ -309,6 +313,7 @@
"PC15", "PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
pwm0_pins: pwm0 {
@ -483,6 +488,9 @@
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
clock-output-names = "osc32k";
clocks = <&ext_osc32k>;
#clock-cells = <1>;
};
nmi_intc: interrupt-controller@01f00c0c {
@ -535,6 +543,10 @@
compatible = "allwinner,sun6i-a31-clock-reset";
#reset-cells = <1>;
};
codec_analog: codec-analog {
compatible = "allwinner,sun8i-a23-codec-analog";
};
};
cpucfg@01f01c00 {
@ -557,7 +569,7 @@
compatible = "allwinner,sun8i-a23-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_rst 0>;
gpio-controller;

23
arch/arm/boot/dts/sun8i-a23-q8-tablet.dts
View File

@ -48,3 +48,26 @@
model = "Q8 A23 Tablet";
compatible = "allwinner,q8-a23", "allwinner,sun8i-a23";
};
&codec {
pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
allwinner,audio-routing =
"Headphone", "HP",
"Headphone", "HPCOM",
"Speaker", "HP",
"MIC1", "Mic",
"MIC2", "Headset Mic",
"Mic", "MBIAS",
"Headset Mic", "HBIAS";
status = "okay";
};
&pio {
codec_pa_pin: codec_pa_pin@0 {
allwinner,pins = "PH9";
allwinner,function = "gpio_out";
allwinner,drive = <SUN4I_PINCTRL_10_MA>;
allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
};
};

16
arch/arm/boot/dts/sun8i-a23.dtsi
View File

@ -48,6 +48,22 @@
memory {
reg = <0x40000000 0x40000000>;
};
soc@01c00000 {
codec: codec@01c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-a23-codec";
reg = <0x01c22c00 0x400>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
clock-names = "apb", "codec";
resets = <&ccu RST_BUS_CODEC>;
dmas = <&dma 15>, <&dma 15>;
dma-names = "rx", "tx";
allwinner,codec-analog-controls = <&codec_analog>;
status = "disabled";
};
};
};
&ccu {

2
arch/arm/boot/dts/sun8i-a33-olinuxino.dts
View File

@ -120,7 +120,7 @@
};
};
#include "axp22x.dtsi"
#include "axp223.dtsi"
&reg_aldo1 {
regulator-always-on;

36
arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts
View File

@ -61,6 +61,27 @@
chosen {
stdout-path = "serial0:115200n8";
};
panel {
compatible = "netron-dy,e231732";
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
panel_input: endpoint@0 {
reg = <0>;
remote-endpoint = <&tcon0_out_panel>;
};
};
};
};
&de {
status = "okay";
};
&ehci0 {
@ -144,7 +165,7 @@
};
};
#include "axp22x.dtsi"
#include "axp223.dtsi"
&reg_aldo1 {
regulator-always-on;
@ -206,6 +227,19 @@
regulator-name = "vcc-rtc";
};
&tcon0 {
pinctrl-names = "default";
pinctrl-0 = <&lcd_rgb666_pins>;
status = "okay";
};
&tcon0_out {
tcon0_out_panel: endpoint@0 {
reg = <0>;
remote-endpoint = <&panel_input>;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_b>;

35
arch/arm/boot/dts/sun8i-a33.dtsi
View File

@ -45,7 +45,42 @@
#include "sun8i-a23-a33.dtsi"
/ {
cpu0_opp_table: opp_table0 {
compatible = "operating-points-v2";
opp-shared;
opp@648000000 {
opp-hz = /bits/ 64 <648000000>;
opp-microvolt = <1040000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
opp@816000000 {
opp-hz = /bits/ 64 <816000000>;
opp-microvolt = <1100000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
opp@1008000000 {
opp-hz = /bits/ 64 <1008000000>;
opp-microvolt = <1200000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
opp@1200000000 {
opp-hz = /bits/ 64 <1200000000>;
opp-microvolt = <1320000>;
clock-latency-ns = <244144>; /* 8 32k periods */
};
};
cpus {
cpu@0 {
clocks = <&ccu CLK_CPUX>;
clock-names = "cpu";
operating-points-v2 = <&cpu0_opp_table>;
};
cpu@2 {
compatible = "arm,cortex-a7";
device_type = "cpu";

1
arch/arm/boot/dts/sun8i-a83t.dtsi
View File

@ -171,6 +171,7 @@
"PF3", "PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
uart0_pins_a: uart0@0 {

160
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts 100644
View File

@ -0,0 +1,160 @@
/*
* Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
*
* Based on sun8i-h3-orangepi-one.dts, which is:
* Copyright (C) 2016 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Zero";
compatible = "xunlong,orangepi-zero", "allwinner,sun8i-h2-plus";
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
ethernet1 = &xr819;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
pwr_led {
label = "orangepi:green:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
status_led {
label = "orangepi:red:status";
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
};
};
reg_vcc_wifi: reg_vcc_wifi {
compatible = "regulator-fixed";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
enable-active-high;
gpio = <&pio 0 20 GPIO_ACTIVE_HIGH>;
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
post-power-on-delay-ms = <200>;
};
};
&ehci1 {
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <&reg_vcc_wifi>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
/*
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
xr819: sdio_wifi@1 {
reg = <1>;
};
};
&mmc1_pins_a {
bias-pull-up;
};
&ohci1 {
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "disabled";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&uart2_pins>;
status = "disabled";
};
&usbphy {
/* USB VBUS is always on */
status = "okay";
};

160
arch/arm/boot/dts/sun8i-h3-beelink-x2.dts 100644
View File

@ -0,0 +1,160 @@
/*
* Copyright (C) 2017 Marcus Cooper <codekipper@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Beelink X2";
compatible = "roofull,beelink-x2", "allwinner,sun8i-h3";
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
ethernet1 = &sdiowifi;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
blue {
label = "beelink-x2:blue:pwr";
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
default-state = "on";
};
red {
label = "beelink-x2:red:standby";
gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */
};
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
};
sound_spdif {
compatible = "simple-audio-card";
simple-audio-card,name = "On-board SPDIF";
simple-audio-card,cpu {
sound-dai = <&spdif>;
};
simple-audio-card,codec {
sound-dai = <&spdif_out>;
};
};
spdif_out: spdif-out {
#sound-dai-cells = <0>;
compatible = "linux,spdif-dit";
};
};
&ehci1 {
status = "okay";
};
&ir {
pinctrl-names = "default";
pinctrl-0 = <&ir_pins_a>;
status = "okay";
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
cd-inverted;
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_a>;
vmmc-supply = <&reg_vcc3v3>;
bus-width = <4>;
non-removable;
status = "okay";
/*
* Explicitly define the sdio device, so that we can add an ethernet
* alias for it (which e.g. makes u-boot set a mac-address).
*/
sdiowifi: sdio_wifi@1 {
reg = <1>;
};
};
&ohci1 {
status = "okay";
};
&spdif {
pinctrl-names = "default";
pinctrl-0 = <&spdif_tx_pins_a>;
status = "okay";
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
/* USB VBUS is on as long as VCC-IO is on */
status = "okay";
};

8
arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
View File

@ -90,6 +90,14 @@
};
};
&codec {
allwinner,audio-routing =
"Line Out", "LINEOUT",
"MIC1", "Mic",
"Mic", "MBIAS";
status = "okay";
};
&ehci1 {
status = "okay";
};

40
arch/arm/boot/dts/sun8i-h3.dtsi
View File

@ -348,6 +348,7 @@
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin: mmc0_cd_pin@0 {
@ -361,6 +362,7 @@
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
@ -370,6 +372,12 @@
"PC15", "PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
spdif_tx_pins_a: spdif@0 {
pins = "PA17";
function = "spdif";
};
spi0_pins: spi0 {
@ -454,6 +462,19 @@
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
};
spdif: spdif@01c21000 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-h3-spdif";
reg = <0x01c21000 0x400>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
resets = <&ccu RST_BUS_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma 2>;
dma-names = "tx";
status = "disabled";
};
pwm: pwm@01c21400 {
compatible = "allwinner,sun8i-h3-pwm";
reg = <0x01c21400 0x8>;
@ -462,6 +483,20 @@
status = "disabled";
};
codec: codec@01c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-h3-codec";
reg = <0x01c22c00 0x400>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
clock-names = "apb", "codec";
resets = <&ccu RST_BUS_CODEC>;
dmas = <&dma 15>, <&dma 15>;
dma-names = "rx", "tx";
allwinner,codec-analog-controls = <&codec_analog>;
status = "disabled";
};
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
@ -577,6 +612,11 @@
#reset-cells = <1>;
};
codec_analog: codec-analog@01f015c0 {
compatible = "allwinner,sun8i-h3-codec-analog";
reg = <0x01f015c0 0x4>;
};
ir: ir@01f02000 {
compatible = "allwinner,sun5i-a13-ir";
clocks = <&apb0_gates 1>, <&ir_clk>;

2
arch/arm/boot/dts/sun8i-r16-parrot.dts
View File

@ -201,7 +201,7 @@
};
};
#include "axp22x.dtsi"
#include "axp223.dtsi"
&reg_aldo1 {
regulator-always-on;

6
arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi
View File

@ -130,7 +130,7 @@
};
};
#include "axp22x.dtsi"
#include "axp223.dtsi"
&reg_aldo1 {
regulator-always-on;
@ -214,6 +214,10 @@
regulator-name = "vcc-rtc";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&r_uart {
pinctrl-names = "default";
pinctrl-0 = <&r_uart_pins_a>;

103
arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts 100644
View File

@ -0,0 +1,103 @@
/*
* Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
/dts-v1/;
#include "sun8i-v3s.dtsi"
#include "sunxi-common-regulators.dtsi"
/ {
model = "Lichee Pi Zero";
compatible = "licheepi,licheepi-zero", "allwinner,sun8i-v3s";
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
leds {
compatible = "gpio-leds";
blue_led {
label = "licheepi:blue:usr";
gpios = <&pio 6 1 GPIO_ACTIVE_LOW>; /* PG1 */
};
green_led {
label = "licheepi:green:usr";
gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
default-state = "on";
};
red_led {
label = "licheepi:red:usr";
gpios = <&pio 6 2 GPIO_ACTIVE_LOW>; /* PG2 */
};
};
};
&mmc0 {
pinctrl-0 = <&mmc0_pins_a>;
pinctrl-names = "default";
broken-cd;
bus-width = <4>;
vmmc-supply = <&reg_vcc3v3>;
status = "okay";
};
&uart0 {
pinctrl-0 = <&uart0_pins_a>;
pinctrl-names = "default";
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy {
usb0_id_det-gpio = <&pio 5 6 GPIO_ACTIVE_HIGH>;
status = "okay";
};

309
arch/arm/boot/dts/sun8i-v3s.dtsi 100644
View File

@ -0,0 +1,309 @@
/*
* Copyright (C) 2016 Icenowy Zheng <icenowy@aosc.xyz>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
#address-cells = <1>;
#size-cells = <1>;
interrupt-parent = <&gic>;
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu@0 {
compatible = "arm,cortex-a7";
device_type = "cpu";
reg = <0>;
clocks = <&ccu 14>;
};
};
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
osc24M: osc24M_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
osc32k: osc32k_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
mmc0: mmc@01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ccu 22>,
<&ccu 45>,
<&ccu 47>,
<&ccu 46>;
clock-names = "ahb",
"mmc",
"output",
"sample";
resets = <&ccu 7>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
mmc1: mmc@01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&ccu 23>,
<&ccu 48>,
<&ccu 50>,
<&ccu 49>;
clock-names = "ahb",
"mmc",
"output",
"sample";
resets = <&ccu 8>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
mmc2: mmc@01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&ccu 24>,
<&ccu 51>,
<&ccu 53>,
<&ccu 52>;
clock-names = "ahb",
"mmc",
"output",
"sample";
resets = <&ccu 9>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
usb_otg: usb@01c19000 {
compatible = "allwinner,sun8i-h3-musb";
reg = <0x01c19000 0x0400>;
clocks = <&ccu 29>;
resets = <&ccu 17>;
interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "mc";
phys = <&usbphy 0>;
phy-names = "usb";
extcon = <&usbphy 0>;
status = "disabled";
};
usbphy: phy@01c19400 {
compatible = "allwinner,sun8i-v3s-usb-phy";
reg = <0x01c19400 0x2c>,
<0x01c1a800 0x4>;
reg-names = "phy_ctrl",
"pmu0";
clocks = <&ccu 56>;
clock-names = "usb0_phy";
resets = <&ccu 0>;
reset-names = "usb0_reset";
status = "disabled";
#phy-cells = <1>;
};
ccu: clock@01c20000 {
compatible = "allwinner,sun8i-v3s-ccu";
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
rtc: rtc@01c20400 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01c20400 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
pio: pinctrl@01c20800 {
compatible = "allwinner,sun8i-v3s-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu 37>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
i2c0_pins: i2c0 {
pins = "PB6", "PB7";
function = "i2c0";
};
uart0_pins_a: uart0@0 {
pins = "PB8", "PB9";
function = "uart0";
};
mmc0_pins_a: mmc0@0 {
pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
};
timer@01c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
wdt0: watchdog@01c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
};
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 40>;
resets = <&ccu 49>;
status = "disabled";
};
uart1: serial@01c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 41>;
resets = <&ccu 50>;
status = "disabled";
};
uart2: serial@01c28800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28800 0x400>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu 42>;
resets = <&ccu 51>;
status = "disabled";
};
i2c0: i2c@01c2ac00 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu 38>;
resets = <&ccu 46>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c1: i2c@01c2b000 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu 39>;
resets = <&ccu 47>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
gic: interrupt-controller@01c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x1000>,
<0x01c84000 0x2000>,
<0x01c86000 0x2000>;
interrupt-controller;
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
};
};

3
arch/arm/boot/dts/sun9i-a80.dtsi
View File

@ -696,6 +696,7 @@
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc1_pins: mmc1 {
@ -703,6 +704,7 @@
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
@ -712,6 +714,7 @@
"PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
uart0_pins_a: uart0@0 {