diff --git a/Documentation/device-mapper/dm-raid.txt b/Documentation/device-mapper/dm-raid.txt index 728c38c242d6..56fb62b09fc5 100644 --- a/Documentation/device-mapper/dm-raid.txt +++ b/Documentation/device-mapper/dm-raid.txt @@ -141,3 +141,4 @@ Version History 1.2.0 Handle creation of arrays that contain failed devices. 1.3.0 Added support for RAID 10 1.3.1 Allow device replacement/rebuild for RAID 10 +1.3.2 Fix/improve redundancy checking for RAID10 diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index 3a268127b054..bc50899e0c81 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -81,7 +81,8 @@ PA31 TXD4 Required properties for pin configuration node: - atmel,pins: 4 integers array, represents a group of pins mux and config setting. The format is atmel,pins = . - The PERIPH 0 means gpio. + The PERIPH 0 means gpio, PERIPH 1 is periph A, PERIPH 2 is periph B... + PIN_BANK 0 is pioA, PIN_BANK 1 is pioB... Bits used for CONFIG: PULL_UP (1 << 0): indicate this pin need a pull up. @@ -126,7 +127,7 @@ pinctrl@fffff400 { pinctrl_dbgu: dbgu-0 { atmel,pins = <1 14 0x1 0x0 /* PB14 periph A */ - 1 15 0x1 0x1>; /* PB15 periph with pullup */ + 1 15 0x1 0x1>; /* PB15 periph A with pullup */ }; }; }; diff --git a/Documentation/filesystems/f2fs.txt b/Documentation/filesystems/f2fs.txt index 8fbd8b46ee34..dcf338e62b71 100644 --- a/Documentation/filesystems/f2fs.txt +++ b/Documentation/filesystems/f2fs.txt @@ -175,9 +175,9 @@ consists of multiple segments as described below. align with the zone size <-| |-> align with the segment size _________________________________________________________________________ - | | | Node | Segment | Segment | | - | Superblock | Checkpoint | Address | Info. | Summary | Main | - | (SB) | (CP) | Table (NAT) | Table (SIT) | Area (SSA) | | + | | | Segment | Node | Segment | | + | Superblock | Checkpoint | Info. | Address | Summary | Main | + | (SB) | (CP) | Table (SIT) | Table (NAT) | Area (SSA) | | |____________|_____2______|______N______|______N______|______N_____|__N___| . . . . @@ -200,14 +200,14 @@ consists of multiple segments as described below. : It contains file system information, bitmaps for valid NAT/SIT sets, orphan inode lists, and summary entries of current active segments. -- Node Address Table (NAT) - : It is composed of a block address table for all the node blocks stored in - Main area. - - Segment Information Table (SIT) : It contains segment information such as valid block count and bitmap for the validity of all the blocks. +- Node Address Table (NAT) + : It is composed of a block address table for all the node blocks stored in + Main area. + - Segment Summary Area (SSA) : It contains summary entries which contains the owner information of all the data and node blocks stored in Main area. @@ -236,13 +236,13 @@ For file system consistency, each CP points to which NAT and SIT copies are valid, as shown as below. +--------+----------+---------+ - | CP | NAT | SIT | + | CP | SIT | NAT | +--------+----------+---------+ . . . . . . . . . . . . +-------+-------+--------+--------+--------+--------+ - | CP #0 | CP #1 | NAT #0 | NAT #1 | SIT #0 | SIT #1 | + | CP #0 | CP #1 | SIT #0 | SIT #1 | NAT #0 | NAT #1 | +-------+-------+--------+--------+--------+--------+ | ^ ^ | | | diff --git a/Documentation/x86/boot.txt b/Documentation/x86/boot.txt index 406d82d5d2bb..3edb4c2887a1 100644 --- a/Documentation/x86/boot.txt +++ b/Documentation/x86/boot.txt @@ -57,6 +57,10 @@ Protocol 2.10: (Kernel 2.6.31) Added a protocol for relaxed alignment Protocol 2.11: (Kernel 3.6) Added a field for offset of EFI handover protocol entry point. +Protocol 2.12: (Kernel 3.9) Added the xloadflags field and extension fields + to struct boot_params for for loading bzImage and ramdisk + above 4G in 64bit. + **** MEMORY LAYOUT The traditional memory map for the kernel loader, used for Image or @@ -182,7 +186,7 @@ Offset Proto Name Meaning 0230/4 2.05+ kernel_alignment Physical addr alignment required for kernel 0234/1 2.05+ relocatable_kernel Whether kernel is relocatable or not 0235/1 2.10+ min_alignment Minimum alignment, as a power of two -0236/2 N/A pad3 Unused +0236/2 2.12+ xloadflags Boot protocol option flags 0238/4 2.06+ cmdline_size Maximum size of the kernel command line 023C/4 2.07+ hardware_subarch Hardware subarchitecture 0240/8 2.07+ hardware_subarch_data Subarchitecture-specific data @@ -582,6 +586,27 @@ Protocol: 2.10+ misaligned kernel. Therefore, a loader should typically try each power-of-two alignment from kernel_alignment down to this alignment. +Field name: xloadflags +Type: read +Offset/size: 0x236/2 +Protocol: 2.12+ + + This field is a bitmask. + + Bit 0 (read): XLF_KERNEL_64 + - If 1, this kernel has the legacy 64-bit entry point at 0x200. + + Bit 1 (read): XLF_CAN_BE_LOADED_ABOVE_4G + - If 1, kernel/boot_params/cmdline/ramdisk can be above 4G. + + Bit 2 (read): XLF_EFI_HANDOVER_32 + - If 1, the kernel supports the 32-bit EFI handoff entry point + given at handover_offset. + + Bit 3 (read): XLF_EFI_HANDOVER_64 + - If 1, the kernel supports the 64-bit EFI handoff entry point + given at handover_offset + 0x200. + Field name: cmdline_size Type: read Offset/size: 0x238/4 diff --git a/Documentation/x86/zero-page.txt b/Documentation/x86/zero-page.txt index cf5437deda81..199f453cb4de 100644 --- a/Documentation/x86/zero-page.txt +++ b/Documentation/x86/zero-page.txt @@ -19,6 +19,9 @@ Offset Proto Name Meaning 090/010 ALL hd1_info hd1 disk parameter, OBSOLETE!! 0A0/010 ALL sys_desc_table System description table (struct sys_desc_table) 0B0/010 ALL olpc_ofw_header OLPC's OpenFirmware CIF and friends +0C0/004 ALL ext_ramdisk_image ramdisk_image high 32bits +0C4/004 ALL ext_ramdisk_size ramdisk_size high 32bits +0C8/004 ALL ext_cmd_line_ptr cmd_line_ptr high 32bits 140/080 ALL edid_info Video mode setup (struct edid_info) 1C0/020 ALL efi_info EFI 32 information (struct efi_info) 1E0/004 ALL alk_mem_k Alternative mem check, in KB @@ -27,6 +30,7 @@ Offset Proto Name Meaning 1E9/001 ALL eddbuf_entries Number of entries in eddbuf (below) 1EA/001 ALL edd_mbr_sig_buf_entries Number of entries in edd_mbr_sig_buffer (below) +1EF/001 ALL sentinel Used to detect broken bootloaders 290/040 ALL edd_mbr_sig_buffer EDD MBR signatures 2D0/A00 ALL e820_map E820 memory map table (array of struct e820entry) diff --git a/MAINTAINERS b/MAINTAINERS index 845becb8d6ef..38fe0ffc5f16 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2966,7 +2966,7 @@ S: Maintained F: drivers/net/ethernet/i825xx/eexpress.* ETHERNET BRIDGE -M: Stephen Hemminger +M: Stephen Hemminger L: bridge@lists.linux-foundation.org L: netdev@vger.kernel.org W: http://www.linuxfoundation.org/en/Net:Bridge @@ -4914,7 +4914,7 @@ S: Maintained MARVELL GIGABIT ETHERNET DRIVERS (skge/sky2) M: Mirko Lindner -M: Stephen Hemminger +M: Stephen Hemminger L: netdev@vger.kernel.org S: Maintained F: drivers/net/ethernet/marvell/sk* @@ -5189,7 +5189,7 @@ S: Supported F: drivers/infiniband/hw/nes/ NETEM NETWORK EMULATOR -M: Stephen Hemminger +M: Stephen Hemminger L: netem@lists.linux-foundation.org S: Maintained F: net/sched/sch_netem.c @@ -6594,7 +6594,7 @@ F: drivers/media/platform/s3c-camif/ F: include/media/s3c_camif.h SERIAL DRIVERS -M: Alan Cox +M: Greg Kroah-Hartman L: linux-serial@vger.kernel.org S: Maintained F: drivers/tty/serial @@ -7097,7 +7097,7 @@ F: include/uapi/sound/ F: sound/ SOUND - SOC LAYER / DYNAMIC AUDIO POWER MANAGEMENT (ASoC) -M: Liam Girdwood +M: Liam Girdwood M: Mark Brown T: git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound.git L: alsa-devel@alsa-project.org (moderated for non-subscribers) diff --git a/Makefile b/Makefile index 253a455d8d8d..2d3c92c774fb 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 3 PATCHLEVEL = 8 SUBLEVEL = 0 -EXTRAVERSION = -rc4 +EXTRAVERSION = -rc5 NAME = Terrified Chipmunk # *DOCUMENTATION* @@ -169,7 +169,7 @@ SUBARCH := $(shell uname -m | sed -e s/i.86/i386/ -e s/sun4u/sparc64/ \ -e s/arm.*/arm/ -e s/sa110/arm/ \ -e s/s390x/s390/ -e s/parisc64/parisc/ \ -e s/ppc.*/powerpc/ -e s/mips.*/mips/ \ - -e s/sh[234].*/sh/ ) + -e s/sh[234].*/sh/ -e s/aarch64.*/arm64/ ) # Cross compiling and selecting different set of gcc/bin-utils # --------------------------------------------------------------------------- diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 2daf6c06beb9..56e1b06aff2b 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -4,6 +4,7 @@ config ARM select ARCH_BINFMT_ELF_RANDOMIZE_PIE select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE select ARCH_HAVE_CUSTOM_GPIO_H + select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST select ARCH_WANT_IPC_PARSE_VERSION select BUILDTIME_EXTABLE_SORT if MMU select CPU_PM if (SUSPEND || CPU_IDLE) diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index 00044026ef1f..9b82facb2561 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -26,7 +26,7 @@ memory { device_type = "memory"; - reg = <0x00000000 0x20000000>; /* 512 MB */ + reg = <0x00000000 0x40000000>; /* 1 GB */ }; soc { diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi index 271855a6e224..e041f42ed711 100644 --- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi @@ -50,27 +50,25 @@ }; gpio0: gpio@d0018100 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018100 0x40>, - <0xd0018800 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018100 0x40>; ngpios = <32>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <16>, <17>, <18>, <19>; + interrupts = <82>, <83>, <84>, <85>; }; gpio1: gpio@d0018140 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018140 0x40>, - <0xd0018840 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018140 0x40>; ngpios = <17>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <20>, <21>, <22>; + interrupts = <87>, <88>, <89>; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi index 1c1937dbce73..9e23bd8c9536 100644 --- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi @@ -51,39 +51,36 @@ }; gpio0: gpio@d0018100 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018100 0x40>, - <0xd0018800 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018100 0x40>; ngpios = <32>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <16>, <17>, <18>, <19>; + interrupts = <82>, <83>, <84>, <85>; }; gpio1: gpio@d0018140 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018140 0x40>, - <0xd0018840 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018140 0x40>; ngpios = <32>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <20>, <21>, <22>, <23>; + interrupts = <87>, <88>, <89>, <90>; }; gpio2: gpio@d0018180 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018180 0x40>, - <0xd0018870 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018180 0x40>; ngpios = <3>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <24>; + interrupts = <91>; }; ethernet@d0034000 { diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi index 4905cf3a5ef8..965966110e38 100644 --- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi +++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi @@ -66,39 +66,36 @@ }; gpio0: gpio@d0018100 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018100 0x40>, - <0xd0018800 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018100 0x40>; ngpios = <32>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <16>, <17>, <18>, <19>; + interrupts = <82>, <83>, <84>, <85>; }; gpio1: gpio@d0018140 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018140 0x40>, - <0xd0018840 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018140 0x40>; ngpios = <32>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <20>, <21>, <22>, <23>; + interrupts = <87>, <88>, <89>, <90>; }; gpio2: gpio@d0018180 { - compatible = "marvell,armadaxp-gpio"; - reg = <0xd0018180 0x40>, - <0xd0018870 0x30>; + compatible = "marvell,orion-gpio"; + reg = <0xd0018180 0x40>; ngpios = <3>; gpio-controller; #gpio-cells = <2>; interrupt-controller; #interrupts-cells = <2>; - interrupts = <24>; + interrupts = <91>; }; ethernet@d0034000 { diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi index e154f242c680..222047f1ece9 100644 --- a/arch/arm/boot/dts/at91rm9200.dtsi +++ b/arch/arm/boot/dts/at91rm9200.dtsi @@ -336,8 +336,8 @@ i2c@0 { compatible = "i2c-gpio"; - gpios = <&pioA 23 0 /* sda */ - &pioA 24 0 /* scl */ + gpios = <&pioA 25 0 /* sda */ + &pioA 26 0 /* scl */ >; i2c-gpio,sda-open-drain; i2c-gpio,scl-open-drain; diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 3a47cf952146..8ecca6948d81 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -143,6 +143,11 @@ atmel,pins = <0 3 0x1 0x0>; /* PA3 periph A */ }; + + pinctrl_usart0_sck: usart0_sck-0 { + atmel,pins = + <0 4 0x1 0x0>; /* PA4 periph A */ + }; }; usart1 { @@ -154,12 +159,17 @@ pinctrl_usart1_rts: usart1_rts-0 { atmel,pins = - <3 27 0x3 0x0>; /* PC27 periph C */ + <2 27 0x3 0x0>; /* PC27 periph C */ }; pinctrl_usart1_cts: usart1_cts-0 { atmel,pins = - <3 28 0x3 0x0>; /* PC28 periph C */ + <2 28 0x3 0x0>; /* PC28 periph C */ + }; + + pinctrl_usart1_sck: usart1_sck-0 { + atmel,pins = + <2 28 0x3 0x0>; /* PC29 periph C */ }; }; @@ -172,46 +182,56 @@ pinctrl_uart2_rts: uart2_rts-0 { atmel,pins = - <0 0 0x2 0x0>; /* PB0 periph B */ + <1 0 0x2 0x0>; /* PB0 periph B */ }; pinctrl_uart2_cts: uart2_cts-0 { atmel,pins = - <0 1 0x2 0x0>; /* PB1 periph B */ + <1 1 0x2 0x0>; /* PB1 periph B */ + }; + + pinctrl_usart2_sck: usart2_sck-0 { + atmel,pins = + <1 2 0x2 0x0>; /* PB2 periph B */ }; }; usart3 { pinctrl_uart3: usart3-0 { atmel,pins = - <3 23 0x2 0x1 /* PC22 periph B with pullup */ - 3 23 0x2 0x0>; /* PC23 periph B */ + <2 23 0x2 0x1 /* PC22 periph B with pullup */ + 2 23 0x2 0x0>; /* PC23 periph B */ }; pinctrl_usart3_rts: usart3_rts-0 { atmel,pins = - <3 24 0x2 0x0>; /* PC24 periph B */ + <2 24 0x2 0x0>; /* PC24 periph B */ }; pinctrl_usart3_cts: usart3_cts-0 { atmel,pins = - <3 25 0x2 0x0>; /* PC25 periph B */ + <2 25 0x2 0x0>; /* PC25 periph B */ + }; + + pinctrl_usart3_sck: usart3_sck-0 { + atmel,pins = + <2 26 0x2 0x0>; /* PC26 periph B */ }; }; uart0 { pinctrl_uart0: uart0-0 { atmel,pins = - <3 8 0x3 0x0 /* PC8 periph C */ - 3 9 0x3 0x1>; /* PC9 periph C with pullup */ + <2 8 0x3 0x0 /* PC8 periph C */ + 2 9 0x3 0x1>; /* PC9 periph C with pullup */ }; }; uart1 { pinctrl_uart1: uart1-0 { atmel,pins = - <3 16 0x3 0x0 /* PC16 periph C */ - 3 17 0x3 0x1>; /* PC17 periph C with pullup */ + <2 16 0x3 0x0 /* PC16 periph C */ + 2 17 0x3 0x1>; /* PC17 periph C with pullup */ }; }; @@ -240,14 +260,14 @@ pinctrl_macb0_rmii_mii: macb0_rmii_mii-0 { atmel,pins = - <1 8 0x1 0x0 /* PA8 periph A */ - 1 11 0x1 0x0 /* PA11 periph A */ - 1 12 0x1 0x0 /* PA12 periph A */ - 1 13 0x1 0x0 /* PA13 periph A */ - 1 14 0x1 0x0 /* PA14 periph A */ - 1 15 0x1 0x0 /* PA15 periph A */ - 1 16 0x1 0x0 /* PA16 periph A */ - 1 17 0x1 0x0>; /* PA17 periph A */ + <1 8 0x1 0x0 /* PB8 periph A */ + 1 11 0x1 0x0 /* PB11 periph A */ + 1 12 0x1 0x0 /* PB12 periph A */ + 1 13 0x1 0x0 /* PB13 periph A */ + 1 14 0x1 0x0 /* PB14 periph A */ + 1 15 0x1 0x0 /* PB15 periph A */ + 1 16 0x1 0x0 /* PB16 periph A */ + 1 17 0x1 0x0>; /* PB17 periph A */ }; }; diff --git a/arch/arm/boot/dts/cros5250-common.dtsi b/arch/arm/boot/dts/cros5250-common.dtsi index fddd17417433..46c098017036 100644 --- a/arch/arm/boot/dts/cros5250-common.dtsi +++ b/arch/arm/boot/dts/cros5250-common.dtsi @@ -96,8 +96,8 @@ fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3 3>; - samsung,dw-mshc-ddr-timing = <1 2 3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; slot@0 { reg = <0>; @@ -120,8 +120,8 @@ fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3 3>; - samsung,dw-mshc-ddr-timing = <1 2 3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; slot@0 { reg = <0>; @@ -141,8 +141,8 @@ fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3 3>; - samsung,dw-mshc-ddr-timing = <1 2 3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; slot@0 { reg = <0>; diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts index fed7d3f9f431..cdee96fca6e2 100644 --- a/arch/arm/boot/dts/dove-cubox.dts +++ b/arch/arm/boot/dts/dove-cubox.dts @@ -26,10 +26,15 @@ }; &uart0 { status = "okay"; }; -&sdio0 { status = "okay"; }; &sata0 { status = "okay"; }; &i2c0 { status = "okay"; }; +&sdio0 { + status = "okay"; + /* sdio0 card detect is connected to wrong pin on CuBox */ + cd-gpios = <&gpio0 12 1>; +}; + &spi0 { status = "okay"; @@ -42,9 +47,14 @@ }; &pinctrl { - pinctrl-0 = <&pmx_gpio_18>; + pinctrl-0 = <&pmx_gpio_12 &pmx_gpio_18>; pinctrl-names = "default"; + pmx_gpio_12: pmx-gpio-12 { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + pmx_gpio_18: pmx-gpio-18 { marvell,pins = "mpp18"; marvell,function = "gpio"; diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts index 942d5761ca97..e05b18f3c33d 100644 --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts @@ -115,8 +115,8 @@ fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3 3>; - samsung,dw-mshc-ddr-timing = <1 2 3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; slot@0 { reg = <0>; @@ -139,8 +139,8 @@ fifo-depth = <0x80>; card-detect-delay = <200>; samsung,dw-mshc-ciu-div = <3>; - samsung,dw-mshc-sdr-timing = <2 3 3>; - samsung,dw-mshc-ddr-timing = <1 2 3>; + samsung,dw-mshc-sdr-timing = <2 3>; + samsung,dw-mshc-ddr-timing = <1 2>; slot@0 { reg = <0>; diff --git a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi index 9bc6785ad228..77d21abfcdf7 100644 --- a/arch/arm/boot/dts/kirkwood-ns2-common.dtsi +++ b/arch/arm/boot/dts/kirkwood-ns2-common.dtsi @@ -1,4 +1,5 @@ /include/ "kirkwood.dtsi" +/include/ "kirkwood-6281.dtsi" / { chosen { @@ -6,6 +7,21 @@ }; ocp@f1000000 { + pinctrl: pinctrl@10000 { + pinctrl-0 = < &pmx_spi &pmx_twsi0 &pmx_uart0 + &pmx_ns2_sata0 &pmx_ns2_sata1>; + pinctrl-names = "default"; + + pmx_ns2_sata0: pmx-ns2-sata0 { + marvell,pins = "mpp21"; + marvell,function = "sata0"; + }; + pmx_ns2_sata1: pmx-ns2-sata1 { + marvell,pins = "mpp20"; + marvell,function = "sata1"; + }; + }; + serial@12000 { clock-frequency = <166666667>; status = "okay"; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 110d6cbb795b..d6ab442b7011 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -36,6 +36,7 @@ reg = <0x10100 0x40>; ngpios = <32>; interrupt-controller; + #interrupt-cells = <2>; interrupts = <35>, <36>, <37>, <38>; }; @@ -46,6 +47,7 @@ reg = <0x10140 0x40>; ngpios = <18>; interrupt-controller; + #interrupt-cells = <2>; interrupts = <39>, <40>, <41>; }; diff --git a/arch/arm/boot/dts/kizbox.dts b/arch/arm/boot/dts/kizbox.dts index e8814fe0e277..b4dc3ed9a3ec 100644 --- a/arch/arm/boot/dts/kizbox.dts +++ b/arch/arm/boot/dts/kizbox.dts @@ -48,6 +48,8 @@ macb0: ethernet@fffc4000 { phy-mode = "mii"; + pinctrl-0 = <&pinctrl_macb_rmii + &pinctrl_macb_rmii_mii_alt>; status = "okay"; }; diff --git a/arch/arm/boot/dts/sunxi.dtsi b/arch/arm/boot/dts/sunxi.dtsi index 8bbc2bfef221..8b36abea9f2e 100644 --- a/arch/arm/boot/dts/sunxi.dtsi +++ b/arch/arm/boot/dts/sunxi.dtsi @@ -60,19 +60,21 @@ }; uart0: uart@01c28000 { - compatible = "ns8250"; + compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; interrupts = <1>; reg-shift = <2>; + reg-io-width = <4>; clock-frequency = <24000000>; status = "disabled"; }; uart1: uart@01c28400 { - compatible = "ns8250"; + compatible = "snps,dw-apb-uart"; reg = <0x01c28400 0x400>; interrupts = <2>; reg-shift = <2>; + reg-io-width = <4>; clock-frequency = <24000000>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts index 1fc405a9ecfb..cf8071ad22d5 100644 --- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts +++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts @@ -45,7 +45,6 @@ reg = <1>; }; -/* A7s disabled till big.LITTLE patches are available... cpu2: cpu@2 { device_type = "cpu"; compatible = "arm,cortex-a7"; @@ -63,7 +62,6 @@ compatible = "arm,cortex-a7"; reg = <0x102>; }; -*/ }; memory@80000000 { diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig index b175577d7abb..1ea959019fcd 100644 --- a/arch/arm/configs/at91_dt_defconfig +++ b/arch/arm/configs/at91_dt_defconfig @@ -19,6 +19,7 @@ CONFIG_SOC_AT91SAM9260=y CONFIG_SOC_AT91SAM9263=y CONFIG_SOC_AT91SAM9G45=y CONFIG_SOC_AT91SAM9X5=y +CONFIG_SOC_AT91SAM9N12=y CONFIG_MACH_AT91SAM_DT=y CONFIG_AT91_PROGRAMMABLE_CLOCKS=y CONFIG_AT91_TIMER_HZ=128 @@ -31,7 +32,7 @@ CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 CONFIG_ARM_APPENDED_DTB=y CONFIG_ARM_ATAG_DTB_COMPAT=y -CONFIG_CMDLINE="mem=128M console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw" +CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 rw" CONFIG_KEXEC=y CONFIG_AUTO_ZRELADDR=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set diff --git a/arch/arm/kernel/debug.S b/arch/arm/kernel/debug.S index 6809200c31fb..14f7c3b14632 100644 --- a/arch/arm/kernel/debug.S +++ b/arch/arm/kernel/debug.S @@ -100,12 +100,14 @@ ENTRY(printch) b 1b ENDPROC(printch) +#ifdef CONFIG_MMU ENTRY(debug_ll_addr) addruart r2, r3, ip str r2, [r0] str r3, [r1] mov pc, lr ENDPROC(debug_ll_addr) +#endif #else diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S index 4eee351f4668..486a15ae9011 100644 --- a/arch/arm/kernel/head.S +++ b/arch/arm/kernel/head.S @@ -246,6 +246,7 @@ __create_page_tables: /* * Then map boot params address in r2 if specified. + * We map 2 sections in case the ATAGs/DTB crosses a section boundary. */ mov r0, r2, lsr #SECTION_SHIFT movs r0, r0, lsl #SECTION_SHIFT @@ -253,6 +254,8 @@ __create_page_tables: addne r3, r3, #PAGE_OFFSET addne r3, r4, r3, lsr #(SECTION_SHIFT - PMD_ORDER) orrne r6, r7, r0 + strne r6, [r3], #1 << PMD_ORDER + addne r6, r6, #1 << SECTION_SHIFT strne r6, [r3] #ifdef CONFIG_DEBUG_LL @@ -331,7 +334,7 @@ ENTRY(secondary_startup) * as it has already been validated by the primary processor. */ #ifdef CONFIG_ARM_VIRT_EXT - bl __hyp_stub_install + bl __hyp_stub_install_secondary #endif safe_svcmode_maskall r9 diff --git a/arch/arm/kernel/hyp-stub.S b/arch/arm/kernel/hyp-stub.S index 65b2417aebce..1315c4ccfa56 100644 --- a/arch/arm/kernel/hyp-stub.S +++ b/arch/arm/kernel/hyp-stub.S @@ -99,7 +99,7 @@ ENTRY(__hyp_stub_install_secondary) * immediately. */ compare_cpu_mode_with_primary r4, r5, r6, r7 - bxne lr + movne pc, lr /* * Once we have given up on one CPU, we do not try to install the @@ -111,7 +111,7 @@ ENTRY(__hyp_stub_install_secondary) */ cmp r4, #HYP_MODE - bxne lr @ give up if the CPU is not in HYP mode + movne pc, lr @ give up if the CPU is not in HYP mode /* * Configure HSCTLR to set correct exception endianness/instruction set @@ -120,7 +120,8 @@ ENTRY(__hyp_stub_install_secondary) * Eventually, CPU-specific code might be needed -- assume not for now * * This code relies on the "eret" instruction to synchronize the - * various coprocessor accesses. + * various coprocessor accesses. This is done when we switch to SVC + * (see safe_svcmode_maskall). */ @ Now install the hypervisor stub: adr r7, __hyp_stub_vectors @@ -155,14 +156,7 @@ THUMB( orr r7, #(1 << 30) ) @ HSCTLR.TE 1: #endif - bic r7, r4, #MODE_MASK - orr r7, r7, #SVC_MODE -THUMB( orr r7, r7, #PSR_T_BIT ) - msr spsr_cxsf, r7 @ This is SPSR_hyp. - - __MSR_ELR_HYP(14) @ msr elr_hyp, lr - __ERET @ return, switching to SVC mode - @ The boot CPU mode is left in r4. + bx lr @ The boot CPU mode is left in r4. ENDPROC(__hyp_stub_install_secondary) __hyp_stub_do_trap: @@ -200,7 +194,7 @@ ENDPROC(__hyp_get_vectors) @ fall through ENTRY(__hyp_set_vectors) __HVC(0) - bx lr + mov pc, lr ENDPROC(__hyp_set_vectors) #ifndef ZIMAGE diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c index 84f4cbf652e5..b7e3b506219b 100644 --- a/arch/arm/kernel/smp.c +++ b/arch/arm/kernel/smp.c @@ -475,14 +475,8 @@ u64 smp_irq_stat_cpu(unsigned int cpu) */ static DEFINE_PER_CPU(struct clock_event_device, percpu_clockevent); -static void ipi_timer(void) -{ - struct clock_event_device *evt = &__get_cpu_var(percpu_clockevent); - evt->event_handler(evt); -} - #ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST -static void smp_timer_broadcast(const struct cpumask *mask) +void tick_broadcast(const struct cpumask *mask) { smp_cross_call(mask, IPI_TIMER); } @@ -530,7 +524,6 @@ static void __cpuinit percpu_timer_setup(void) struct clock_event_device *evt = &per_cpu(percpu_clockevent, cpu); evt->cpumask = cpumask_of(cpu); - evt->broadcast = smp_timer_broadcast; if (!lt_ops || lt_ops->setup(evt)) broadcast_timer_setup(evt); @@ -596,11 +589,13 @@ void handle_IPI(int ipinr, struct pt_regs *regs) case IPI_WAKEUP: break; +#ifdef CONFIG_GENERIC_CLOCKEVENTS_BROADCAST case IPI_TIMER: irq_enter(); - ipi_timer(); + tick_receive_broadcast(); irq_exit(); break; +#endif case IPI_RESCHEDULE: scheduler_ipi(); diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index 9ee866ce0478..4b678478cf95 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -105,6 +105,8 @@ static void __init soc_detect(u32 dbgu_base) switch (socid) { case ARCH_ID_AT91RM9200: at91_soc_initdata.type = AT91_SOC_RM9200; + if (at91_soc_initdata.subtype == AT91_SOC_SUBTYPE_NONE) + at91_soc_initdata.subtype = AT91_SOC_RM9200_BGA; at91_boot_soc = at91rm9200_soc; break; diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig index 3e628fd7a674..0a2349dc7018 100644 --- a/arch/arm/mach-imx/Kconfig +++ b/arch/arm/mach-imx/Kconfig @@ -851,6 +851,7 @@ config SOC_IMX6Q select HAVE_CAN_FLEXCAN if CAN select HAVE_IMX_GPC select HAVE_IMX_MMDC + select HAVE_IMX_SRC select HAVE_SMP select MFD_SYSCON select PINCTRL diff --git a/arch/arm/mach-imx/clk-imx25.c b/arch/arm/mach-imx/clk-imx25.c index b197aa73dc4b..2c570cdaae7b 100644 --- a/arch/arm/mach-imx/clk-imx25.c +++ b/arch/arm/mach-imx/clk-imx25.c @@ -254,9 +254,9 @@ int __init mx25_clocks_init(void) clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2"); clk_register_clkdev(clk[usbotg_ahb], "ahb", "mxc-ehci.2"); clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2"); - clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc"); - clk_register_clkdev(clk[usbotg_ahb], "ahb", "fsl-usb2-udc"); - clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc"); + clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27"); + clk_register_clkdev(clk[usbotg_ahb], "ahb", "imx-udc-mx27"); + clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27"); clk_register_clkdev(clk[nfc_ipg_per], NULL, "imx25-nand.0"); /* i.mx25 has the i.mx35 type cspi */ clk_register_clkdev(clk[cspi1_ipg], NULL, "imx35-cspi.0"); diff --git a/arch/arm/mach-imx/clk-imx27.c b/arch/arm/mach-imx/clk-imx27.c index 4c1d1e4efc74..1ffe3b534e51 100644 --- a/arch/arm/mach-imx/clk-imx27.c +++ b/arch/arm/mach-imx/clk-imx27.c @@ -236,9 +236,9 @@ int __init mx27_clocks_init(unsigned long fref) clk_register_clkdev(clk[lcdc_ahb_gate], "ahb", "imx21-fb.0"); clk_register_clkdev(clk[csi_ahb_gate], "ahb", "imx27-camera.0"); clk_register_clkdev(clk[per4_gate], "per", "imx27-camera.0"); - clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc"); - clk_register_clkdev(clk[usb_ipg_gate], "ipg", "fsl-usb2-udc"); - clk_register_clkdev(clk[usb_ahb_gate], "ahb", "fsl-usb2-udc"); + clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27"); + clk_register_clkdev(clk[usb_ipg_gate], "ipg", "imx-udc-mx27"); + clk_register_clkdev(clk[usb_ahb_gate], "ahb", "imx-udc-mx27"); clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.0"); clk_register_clkdev(clk[usb_ipg_gate], "ipg", "mxc-ehci.0"); clk_register_clkdev(clk[usb_ahb_gate], "ahb", "mxc-ehci.0"); diff --git a/arch/arm/mach-imx/clk-imx31.c b/arch/arm/mach-imx/clk-imx31.c index 8be64e0a4ace..16ccbd41dea9 100644 --- a/arch/arm/mach-imx/clk-imx31.c +++ b/arch/arm/mach-imx/clk-imx31.c @@ -139,9 +139,9 @@ int __init mx31_clocks_init(unsigned long fref) clk_register_clkdev(clk[usb_div_post], "per", "mxc-ehci.2"); clk_register_clkdev(clk[usb_gate], "ahb", "mxc-ehci.2"); clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2"); - clk_register_clkdev(clk[usb_div_post], "per", "fsl-usb2-udc"); - clk_register_clkdev(clk[usb_gate], "ahb", "fsl-usb2-udc"); - clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc"); + clk_register_clkdev(clk[usb_div_post], "per", "imx-udc-mx27"); + clk_register_clkdev(clk[usb_gate], "ahb", "imx-udc-mx27"); + clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27"); clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0"); /* i.mx31 has the i.mx21 type uart */ clk_register_clkdev(clk[uart1_gate], "per", "imx21-uart.0"); diff --git a/arch/arm/mach-imx/clk-imx35.c b/arch/arm/mach-imx/clk-imx35.c index 66f3d65ea275..f0727e80815d 100644 --- a/arch/arm/mach-imx/clk-imx35.c +++ b/arch/arm/mach-imx/clk-imx35.c @@ -251,9 +251,9 @@ int __init mx35_clocks_init() clk_register_clkdev(clk[usb_div], "per", "mxc-ehci.2"); clk_register_clkdev(clk[ipg], "ipg", "mxc-ehci.2"); clk_register_clkdev(clk[usbotg_gate], "ahb", "mxc-ehci.2"); - clk_register_clkdev(clk[usb_div], "per", "fsl-usb2-udc"); - clk_register_clkdev(clk[ipg], "ipg", "fsl-usb2-udc"); - clk_register_clkdev(clk[usbotg_gate], "ahb", "fsl-usb2-udc"); + clk_register_clkdev(clk[usb_div], "per", "imx-udc-mx27"); + clk_register_clkdev(clk[ipg], "ipg", "imx-udc-mx27"); + clk_register_clkdev(clk[usbotg_gate], "ahb", "imx-udc-mx27"); clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0"); clk_register_clkdev(clk[nfc_div], NULL, "imx25-nand.0"); clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0"); diff --git a/arch/arm/mach-imx/clk-imx51-imx53.c b/arch/arm/mach-imx/clk-imx51-imx53.c index 579023f59dc1..fb7cb841b64c 100644 --- a/arch/arm/mach-imx/clk-imx51-imx53.c +++ b/arch/arm/mach-imx/clk-imx51-imx53.c @@ -269,9 +269,9 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil, clk_register_clkdev(clk[usboh3_per_gate], "per", "mxc-ehci.2"); clk_register_clkdev(clk[usboh3_gate], "ipg", "mxc-ehci.2"); clk_register_clkdev(clk[usboh3_gate], "ahb", "mxc-ehci.2"); - clk_register_clkdev(clk[usboh3_per_gate], "per", "fsl-usb2-udc"); - clk_register_clkdev(clk[usboh3_gate], "ipg", "fsl-usb2-udc"); - clk_register_clkdev(clk[usboh3_gate], "ahb", "fsl-usb2-udc"); + clk_register_clkdev(clk[usboh3_per_gate], "per", "imx-udc-mx51"); + clk_register_clkdev(clk[usboh3_gate], "ipg", "imx-udc-mx51"); + clk_register_clkdev(clk[usboh3_gate], "ahb", "imx-udc-mx51"); clk_register_clkdev(clk[nfc_gate], NULL, "imx51-nand"); clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "imx-ssi.0"); clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "imx-ssi.1"); diff --git a/arch/arm/mach-imx/clk-imx6q.c b/arch/arm/mach-imx/clk-imx6q.c index 7f2c10c7413a..c0c4e723b7f5 100644 --- a/arch/arm/mach-imx/clk-imx6q.c +++ b/arch/arm/mach-imx/clk-imx6q.c @@ -436,6 +436,9 @@ int __init mx6q_clocks_init(void) for (i = 0; i < ARRAY_SIZE(clks_init_on); i++) clk_prepare_enable(clk[clks_init_on[i]]); + /* Set initial power mode */ + imx6q_set_lpm(WAIT_CLOCKED); + np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt"); base = of_iomap(np, 0); WARN_ON(!base); diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h index 7191ab4434e5..fa36fb84ab19 100644 --- a/arch/arm/mach-imx/common.h +++ b/arch/arm/mach-imx/common.h @@ -142,6 +142,7 @@ extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode); extern void imx6q_clock_map_io(void); extern void imx_cpu_die(unsigned int cpu); +extern int imx_cpu_kill(unsigned int cpu); #ifdef CONFIG_PM extern void imx6q_pm_init(void); diff --git a/arch/arm/mach-imx/devices/devices-common.h b/arch/arm/mach-imx/devices/devices-common.h index 6277baf1b7be..9bd5777ff0e7 100644 --- a/arch/arm/mach-imx/devices/devices-common.h +++ b/arch/arm/mach-imx/devices/devices-common.h @@ -63,6 +63,7 @@ struct platform_device *__init imx_add_flexcan( #include struct imx_fsl_usb2_udc_data { + const char *devid; resource_size_t iobase; resource_size_t irq; }; diff --git a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c index 37e44398197b..3c06bd96e9cc 100644 --- a/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c +++ b/arch/arm/mach-imx/devices/platform-fsl-usb2-udc.c @@ -11,35 +11,36 @@ #include "../hardware.h" #include "devices-common.h" -#define imx_fsl_usb2_udc_data_entry_single(soc) \ +#define imx_fsl_usb2_udc_data_entry_single(soc, _devid) \ { \ + .devid = _devid, \ .iobase = soc ## _USB_OTG_BASE_ADDR, \ .irq = soc ## _INT_USB_OTG, \ } #ifdef CONFIG_SOC_IMX25 const struct imx_fsl_usb2_udc_data imx25_fsl_usb2_udc_data __initconst = - imx_fsl_usb2_udc_data_entry_single(MX25); + imx_fsl_usb2_udc_data_entry_single(MX25, "imx-udc-mx27"); #endif /* ifdef CONFIG_SOC_IMX25 */ #ifdef CONFIG_SOC_IMX27 const struct imx_fsl_usb2_udc_data imx27_fsl_usb2_udc_data __initconst = - imx_fsl_usb2_udc_data_entry_single(MX27); + imx_fsl_usb2_udc_data_entry_single(MX27, "imx-udc-mx27"); #endif /* ifdef CONFIG_SOC_IMX27 */ #ifdef CONFIG_SOC_IMX31 const struct imx_fsl_usb2_udc_data imx31_fsl_usb2_udc_data __initconst = - imx_fsl_usb2_udc_data_entry_single(MX31); + imx_fsl_usb2_udc_data_entry_single(MX31, "imx-udc-mx27"); #endif /* ifdef CONFIG_SOC_IMX31 */ #ifdef CONFIG_SOC_IMX35 const struct imx_fsl_usb2_udc_data imx35_fsl_usb2_udc_data __initconst = - imx_fsl_usb2_udc_data_entry_single(MX35); + imx_fsl_usb2_udc_data_entry_single(MX35, "imx-udc-mx27"); #endif /* ifdef CONFIG_SOC_IMX35 */ #ifdef CONFIG_SOC_IMX51 const struct imx_fsl_usb2_udc_data imx51_fsl_usb2_udc_data __initconst = - imx_fsl_usb2_udc_data_entry_single(MX51); + imx_fsl_usb2_udc_data_entry_single(MX51, "imx-udc-mx51"); #endif struct platform_device *__init imx_add_fsl_usb2_udc( @@ -57,7 +58,7 @@ struct platform_device *__init imx_add_fsl_usb2_udc( .flags = IORESOURCE_IRQ, }, }; - return imx_add_platform_device_dmamask("fsl-usb2-udc", -1, + return imx_add_platform_device_dmamask(data->devid, -1, res, ARRAY_SIZE(res), pdata, sizeof(*pdata), DMA_BIT_MASK(32)); } diff --git a/arch/arm/mach-imx/devices/platform-imx-fb.c b/arch/arm/mach-imx/devices/platform-imx-fb.c index 10b0ed39f07f..25a47c616b2d 100644 --- a/arch/arm/mach-imx/devices/platform-imx-fb.c +++ b/arch/arm/mach-imx/devices/platform-imx-fb.c @@ -54,7 +54,7 @@ struct platform_device *__init imx_add_imx_fb( .flags = IORESOURCE_IRQ, }, }; - return imx_add_platform_device_dmamask("imx-fb", 0, + return imx_add_platform_device_dmamask(data->devid, 0, res, ARRAY_SIZE(res), pdata, sizeof(*pdata), DMA_BIT_MASK(32)); } diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c index 3dec962b0770..7bc5fe15dda2 100644 --- a/arch/arm/mach-imx/hotplug.c +++ b/arch/arm/mach-imx/hotplug.c @@ -46,9 +46,11 @@ static inline void cpu_enter_lowpower(void) void imx_cpu_die(unsigned int cpu) { cpu_enter_lowpower(); - imx_enable_cpu(cpu, false); - - /* spin here until hardware takes it down */ - while (1) - ; + cpu_do_idle(); +} + +int imx_cpu_kill(unsigned int cpu) +{ + imx_enable_cpu(cpu, false); + return 1; } diff --git a/arch/arm/mach-imx/iram_alloc.c b/arch/arm/mach-imx/iram_alloc.c index 6c80424f678e..e05cf407db65 100644 --- a/arch/arm/mach-imx/iram_alloc.c +++ b/arch/arm/mach-imx/iram_alloc.c @@ -22,8 +22,7 @@ #include #include #include - -#include "iram.h" +#include "linux/platform_data/imx-iram.h" static unsigned long iram_phys_base; static void __iomem *iram_virt_base; diff --git a/arch/arm/mach-imx/platsmp.c b/arch/arm/mach-imx/platsmp.c index 3777b805b76b..66fae885c842 100644 --- a/arch/arm/mach-imx/platsmp.c +++ b/arch/arm/mach-imx/platsmp.c @@ -92,5 +92,6 @@ struct smp_operations imx_smp_ops __initdata = { .smp_boot_secondary = imx_boot_secondary, #ifdef CONFIG_HOTPLUG_CPU .cpu_die = imx_cpu_die, + .cpu_kill = imx_cpu_kill, #endif }; diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c index a17543da602d..ee42d20cba19 100644 --- a/arch/arm/mach-imx/pm-imx6q.c +++ b/arch/arm/mach-imx/pm-imx6q.c @@ -41,6 +41,7 @@ static int imx6q_pm_enter(suspend_state_t state) cpu_suspend(0, imx6q_suspend_finish); imx_smp_prepare(); imx_gpc_post_resume(); + imx6q_set_lpm(WAIT_CLOCKED); break; default: return -EINVAL; diff --git a/arch/arm/mach-integrator/pci_v3.c b/arch/arm/mach-integrator/pci_v3.c index be50e795536d..e7fcea7f3300 100644 --- a/arch/arm/mach-integrator/pci_v3.c +++ b/arch/arm/mach-integrator/pci_v3.c @@ -475,13 +475,12 @@ int __init pci_v3_setup(int nr, struct pci_sys_data *sys) { int ret = 0; + if (!ap_syscon_base) + return -EINVAL; + if (nr == 0) { sys->mem_offset = PHYS_PCI_MEM_BASE; ret = pci_v3_setup_resources(sys); - /* Remap the Integrator system controller */ - ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100); - if (!ap_syscon_base) - return -EINVAL; } return ret; @@ -497,6 +496,13 @@ void __init pci_v3_preinit(void) unsigned int temp; int ret; + /* Remap the Integrator system controller */ + ap_syscon_base = ioremap(INTEGRATOR_SC_BASE, 0x100); + if (!ap_syscon_base) { + pr_err("unable to remap the AP syscon for PCIv3\n"); + return; + } + pcibios_min_mem = 0x00100000; /* diff --git a/arch/arm/mach-kirkwood/board-ns2.c b/arch/arm/mach-kirkwood/board-ns2.c index 8821720ab5a4..f4632a809f68 100644 --- a/arch/arm/mach-kirkwood/board-ns2.c +++ b/arch/arm/mach-kirkwood/board-ns2.c @@ -18,47 +18,11 @@ #include #include #include "common.h" -#include "mpp.h" static struct mv643xx_eth_platform_data ns2_ge00_data = { .phy_addr = MV643XX_ETH_PHY_ADDR(8), }; -static unsigned int ns2_mpp_config[] __initdata = { - MPP0_SPI_SCn, - MPP1_SPI_MOSI, - MPP2_SPI_SCK, - MPP3_SPI_MISO, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, /* Fan speed (bit 1) */ - MPP8_TW0_SDA, - MPP9_TW0_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_GPO, /* Red led */ - MPP14_GPIO, /* USB fuse */ - MPP16_GPIO, /* SATA 0 power */ - MPP17_GPIO, /* SATA 1 power */ - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_SATA1_ACTn, - MPP21_SATA0_ACTn, - MPP22_GPIO, /* Fan speed (bit 0) */ - MPP23_GPIO, /* Fan power */ - MPP24_GPIO, /* USB mode select */ - MPP25_GPIO, /* Fan rotation fail */ - MPP26_GPIO, /* USB device vbus */ - MPP28_GPIO, /* USB enable host vbus */ - MPP29_GPIO, /* Blue led (slow register) */ - MPP30_GPIO, /* Blue led (command register) */ - MPP31_GPIO, /* Board power off */ - MPP32_GPIO, /* Power button (0 = Released, 1 = Pushed) */ - MPP33_GPO, /* Fan speed (bit 2) */ - 0 -}; - #define NS2_GPIO_POWER_OFF 31 static void ns2_power_off(void) @@ -71,8 +35,6 @@ void __init ns2_init(void) /* * Basic setup. Needs to be called early. */ - kirkwood_mpp_conf(ns2_mpp_config); - if (of_machine_is_compatible("lacie,netspace_lite_v2") || of_machine_is_compatible("lacie,netspace_mini_v2")) ns2_ge00_data.phy_addr = MV643XX_ETH_PHY_ADDR(0); diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile index 5dcb369b58aa..99df4df680fd 100644 --- a/arch/arm/mach-mvebu/Makefile +++ b/arch/arm/mach-mvebu/Makefile @@ -1,6 +1,8 @@ ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \ -I$(srctree)/arch/arm/plat-orion/include +AFLAGS_coherency_ll.o := -Wa,-march=armv7-a + obj-y += system-controller.o obj-$(CONFIG_MACH_ARMADA_370_XP) += armada-370-xp.o irq-armada-370-xp.o addr-map.o coherency.o coherency_ll.o pmsu.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c index 5c8e9cee2c2e..769c1feee1c4 100644 --- a/arch/arm/mach-omap2/board-omap4panda.c +++ b/arch/arm/mach-omap2/board-omap4panda.c @@ -397,6 +397,12 @@ static struct omap_board_mux board_mux[] __initdata = { OMAP_PULL_ENA), OMAP4_MUX(ABE_MCBSP1_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT), + /* UART2 - BT/FM/GPS shared transport */ + OMAP4_MUX(UART2_CTS, OMAP_PIN_INPUT | OMAP_MUX_MODE0), + OMAP4_MUX(UART2_RTS, OMAP_PIN_OUTPUT | OMAP_MUX_MODE0), + OMAP4_MUX(UART2_RX, OMAP_PIN_INPUT | OMAP_MUX_MODE0), + OMAP4_MUX(UART2_TX, OMAP_PIN_OUTPUT | OMAP_MUX_MODE0), + { .reg_offset = OMAP_MUX_TERMINATOR }, }; diff --git a/arch/arm/mach-omap2/cclock2420_data.c b/arch/arm/mach-omap2/cclock2420_data.c index 7e5febe456d9..ab7e952d2070 100644 --- a/arch/arm/mach-omap2/cclock2420_data.c +++ b/arch/arm/mach-omap2/cclock2420_data.c @@ -1935,6 +1935,8 @@ int __init omap2420_clk_init(void) omap2_init_clk_hw_omap_clocks(c->lk.clk); } + omap2xxx_clkt_vps_late_init(); + omap2_clk_disable_autoidle_all(); omap2_clk_enable_init_clocks(enable_init_clks, diff --git a/arch/arm/mach-omap2/cclock2430_data.c b/arch/arm/mach-omap2/cclock2430_data.c index eda079b96c6a..eb3dab68d536 100644 --- a/arch/arm/mach-omap2/cclock2430_data.c +++ b/arch/arm/mach-omap2/cclock2430_data.c @@ -2050,6 +2050,8 @@ int __init omap2430_clk_init(void) omap2_init_clk_hw_omap_clocks(c->lk.clk); } + omap2xxx_clkt_vps_late_init(); + omap2_clk_disable_autoidle_all(); omap2_clk_enable_init_clocks(enable_init_clks, diff --git a/arch/arm/mach-omap2/cclock44xx_data.c b/arch/arm/mach-omap2/cclock44xx_data.c index 5789a5e25563..a2cc046b47f4 100644 --- a/arch/arm/mach-omap2/cclock44xx_data.c +++ b/arch/arm/mach-omap2/cclock44xx_data.c @@ -2026,14 +2026,13 @@ int __init omap4xxx_clk_init(void) * On OMAP4460 the ABE DPLL fails to turn on if in idle low-power * state when turning the ABE clock domain. Workaround this by * locking the ABE DPLL on boot. + * Lock the ABE DPLL in any case to avoid issues with audio. */ - if (cpu_is_omap446x()) { - rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck); - if (!rc) - rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ); - if (rc) - pr_err("%s: failed to configure ABE DPLL!\n", __func__); - } + rc = clk_set_parent(&abe_dpll_refclk_mux_ck, &sys_32k_ck); + if (!rc) + rc = clk_set_rate(&dpll_abe_ck, OMAP4_DPLL_ABE_DEFFREQ); + if (rc) + pr_err("%s: failed to configure ABE DPLL!\n", __func__); return 0; } diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 5e304d0719a2..626f3ea3142f 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -639,7 +639,7 @@ static int count_ocp2scp_devices(struct omap_ocp2scp_dev *ocp2scp_dev) return cnt; } -static void omap_init_ocp2scp(void) +static void __init omap_init_ocp2scp(void) { struct omap_hwmod *oh; struct platform_device *pdev; diff --git a/arch/arm/mach-omap2/drm.c b/arch/arm/mach-omap2/drm.c index 4c7566c7e24a..2a2cfa88ddbf 100644 --- a/arch/arm/mach-omap2/drm.c +++ b/arch/arm/mach-omap2/drm.c @@ -25,6 +25,7 @@ #include #include +#include "soc.h" #include "omap_device.h" #include "omap_hwmod.h" @@ -56,7 +57,7 @@ static int __init omap_init_drm(void) oh->name); } - platform_data.omaprev = GET_OMAP_REVISION(); + platform_data.omaprev = GET_OMAP_TYPE; return platform_device_register(&omap_drm_device); diff --git a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c index 129d5081ed15..793f54ac7d14 100644 --- a/arch/arm/mach-omap2/omap_hwmod_44xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_44xx_data.c @@ -2132,8 +2132,12 @@ static struct omap_hwmod omap44xx_mcpdm_hwmod = { * currently reset very early during boot, before I2C is * available, so it doesn't seem that we have any choice in * the kernel other than to avoid resetting it. + * + * Also, McPDM needs to be configured to NO_IDLE mode when it + * is in used otherwise vital clocks will be gated which + * results 'slow motion' audio playback. */ - .flags = HWMOD_EXT_OPT_MAIN_CLK, + .flags = HWMOD_EXT_OPT_MAIN_CLK | HWMOD_SWSUP_SIDLE, .mpu_irqs = omap44xx_mcpdm_irqs, .sdma_reqs = omap44xx_mcpdm_sdma_reqs, .main_clk = "mcpdm_fck", diff --git a/arch/arm/mach-omap2/timer.c b/arch/arm/mach-omap2/timer.c index 691aa674665a..b8ad6e632bb8 100644 --- a/arch/arm/mach-omap2/timer.c +++ b/arch/arm/mach-omap2/timer.c @@ -165,15 +165,11 @@ static struct device_node * __init omap_get_timer_dt(struct of_device_id *match, struct device_node *np; for_each_matching_node(np, match) { - if (!of_device_is_available(np)) { - of_node_put(np); + if (!of_device_is_available(np)) continue; - } - if (property && !of_get_property(np, property, NULL)) { - of_node_put(np); + if (property && !of_get_property(np, property, NULL)) continue; - } of_add_property(np, &device_disabled); return np; diff --git a/arch/arm/mach-s3c64xx/mach-crag6410-module.c b/arch/arm/mach-s3c64xx/mach-crag6410-module.c index 553059f51841..755c0bb119f4 100644 --- a/arch/arm/mach-s3c64xx/mach-crag6410-module.c +++ b/arch/arm/mach-s3c64xx/mach-crag6410-module.c @@ -47,7 +47,7 @@ static struct spi_board_info wm1253_devs[] = { .bus_num = 0, .chip_select = 0, .mode = SPI_MODE_0, - .irq = S3C_EINT(5), + .irq = S3C_EINT(4), .controller_data = &wm0010_spi_csinfo, .platform_data = &wm0010_pdata, }, diff --git a/arch/arm/mach-s3c64xx/pm.c b/arch/arm/mach-s3c64xx/pm.c index 7feb426fc202..d2e1a16690bd 100644 --- a/arch/arm/mach-s3c64xx/pm.c +++ b/arch/arm/mach-s3c64xx/pm.c @@ -338,8 +338,10 @@ int __init s3c64xx_pm_init(void) for (i = 0; i < ARRAY_SIZE(s3c64xx_pm_domains); i++) pm_genpd_init(&s3c64xx_pm_domains[i]->pd, NULL, false); +#ifdef CONFIG_S3C_DEV_FB if (dev_get_platdata(&s3c_device_fb.dev)) pm_genpd_add_device(&s3c64xx_pm_f.pd, &s3c_device_fb.dev); +#endif return 0; } diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c index 6b2fb87c8698..076c26d43864 100644 --- a/arch/arm/mm/dma-mapping.c +++ b/arch/arm/mm/dma-mapping.c @@ -774,25 +774,27 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset, size_t size, enum dma_data_direction dir, void (*op)(const void *, size_t, int)) { + unsigned long pfn; + size_t left = size; + + pfn = page_to_pfn(page) + offset / PAGE_SIZE; + offset %= PAGE_SIZE; + /* * A single sg entry may refer to multiple physically contiguous * pages. But we still need to process highmem pages individually. * If highmem is not configured then the bulk of this loop gets * optimized out. */ - size_t left = size; do { size_t len = left; void *vaddr; + page = pfn_to_page(pfn); + if (PageHighMem(page)) { - if (len + offset > PAGE_SIZE) { - if (offset >= PAGE_SIZE) { - page += offset / PAGE_SIZE; - offset %= PAGE_SIZE; - } + if (len + offset > PAGE_SIZE) len = PAGE_SIZE - offset; - } vaddr = kmap_high_get(page); if (vaddr) { vaddr += offset; @@ -809,7 +811,7 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset, op(vaddr, len, dir); } offset = 0; - page++; + pfn++; left -= len; } while (left); } diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c index 1f51d712b55a..8fcf8bd3ee49 100644 --- a/arch/arm/mm/mmu.c +++ b/arch/arm/mm/mmu.c @@ -298,7 +298,7 @@ static struct mem_type mem_types[] = { }, [MT_MEMORY_SO] = { .prot_pte = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY | - L_PTE_MT_UNCACHED, + L_PTE_MT_UNCACHED | L_PTE_XN, .prot_l1 = PMD_TYPE_TABLE, .prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_SECT_S | PMD_SECT_UNCACHED | PMD_SECT_XN, diff --git a/arch/arm/plat-versatile/headsmp.S b/arch/arm/plat-versatile/headsmp.S index dd703ef09b8d..b178d44e9eaa 100644 --- a/arch/arm/plat-versatile/headsmp.S +++ b/arch/arm/plat-versatile/headsmp.S @@ -20,7 +20,7 @@ */ ENTRY(versatile_secondary_startup) mrc p15, 0, r0, c0, c0, 5 - and r0, r0, #15 + bic r0, #0xff000000 adr r4, 1f ldmia r4, {r5, r6} sub r4, r4, r5 diff --git a/arch/arm/vfp/entry.S b/arch/arm/vfp/entry.S index cc926c985981..323ce1a62bbf 100644 --- a/arch/arm/vfp/entry.S +++ b/arch/arm/vfp/entry.S @@ -22,7 +22,7 @@ @ IRQs disabled. @ ENTRY(do_vfp) -#ifdef CONFIG_PREEMPT +#ifdef CONFIG_PREEMPT_COUNT ldr r4, [r10, #TI_PREEMPT] @ get preempt count add r11, r4, #1 @ increment it str r11, [r10, #TI_PREEMPT] @@ -35,7 +35,7 @@ ENTRY(do_vfp) ENDPROC(do_vfp) ENTRY(vfp_null_entry) -#ifdef CONFIG_PREEMPT +#ifdef CONFIG_PREEMPT_COUNT get_thread_info r10 ldr r4, [r10, #TI_PREEMPT] @ get preempt count sub r11, r4, #1 @ decrement it @@ -53,7 +53,7 @@ ENDPROC(vfp_null_entry) __INIT ENTRY(vfp_testing_entry) -#ifdef CONFIG_PREEMPT +#ifdef CONFIG_PREEMPT_COUNT get_thread_info r10 ldr r4, [r10, #TI_PREEMPT] @ get preempt count sub r11, r4, #1 @ decrement it diff --git a/arch/arm/vfp/vfphw.S b/arch/arm/vfp/vfphw.S index ea0349f63586..dd5e56f95f3f 100644 --- a/arch/arm/vfp/vfphw.S +++ b/arch/arm/vfp/vfphw.S @@ -168,7 +168,7 @@ vfp_hw_state_valid: @ else it's one 32-bit instruction, so @ always subtract 4 from the following @ instruction address. -#ifdef CONFIG_PREEMPT +#ifdef CONFIG_PREEMPT_COUNT get_thread_info r10 ldr r4, [r10, #TI_PREEMPT] @ get preempt count sub r11, r4, #1 @ decrement it @@ -192,7 +192,7 @@ look_for_VFP_exceptions: @ not recognised by VFP DBGSTR "not VFP" -#ifdef CONFIG_PREEMPT +#ifdef CONFIG_PREEMPT_COUNT get_thread_info r10 ldr r4, [r10, #TI_PREEMPT] @ get preempt count sub r11, r4, #1 @ decrement it diff --git a/arch/arm64/include/asm/elf.h b/arch/arm64/include/asm/elf.h index 07fea290d7c1..fe32c0e4ac01 100644 --- a/arch/arm64/include/asm/elf.h +++ b/arch/arm64/include/asm/elf.h @@ -26,7 +26,10 @@ typedef unsigned long elf_greg_t; -#define ELF_NGREG (sizeof (struct pt_regs) / sizeof(elf_greg_t)) +#define ELF_NGREG (sizeof(struct user_pt_regs) / sizeof(elf_greg_t)) +#define ELF_CORE_COPY_REGS(dest, regs) \ + *(struct user_pt_regs *)&(dest) = (regs)->user_regs; + typedef elf_greg_t elf_gregset_t[ELF_NGREG]; typedef struct user_fpsimd_state elf_fpregset_t; diff --git a/arch/ia64/kernel/ptrace.c b/arch/ia64/kernel/ptrace.c index 4265ff64219b..b7a5fffe0924 100644 --- a/arch/ia64/kernel/ptrace.c +++ b/arch/ia64/kernel/ptrace.c @@ -672,33 +672,6 @@ ptrace_attach_sync_user_rbs (struct task_struct *child) read_unlock(&tasklist_lock); } -static inline int -thread_matches (struct task_struct *thread, unsigned long addr) -{ - unsigned long thread_rbs_end; - struct pt_regs *thread_regs; - - if (ptrace_check_attach(thread, 0) < 0) - /* - * If the thread is not in an attachable state, we'll - * ignore it. The net effect is that if ADDR happens - * to overlap with the portion of the thread's - * register backing store that is currently residing - * on the thread's kernel stack, then ptrace() may end - * up accessing a stale value. But if the thread - * isn't stopped, that's a problem anyhow, so we're - * doing as well as we can... - */ - return 0; - - thread_regs = task_pt_regs(thread); - thread_rbs_end = ia64_get_user_rbs_end(thread, thread_regs, NULL); - if (!on_kernel_rbs(addr, thread_regs->ar_bspstore, thread_rbs_end)) - return 0; - - return 1; /* looks like we've got a winner */ -} - /* * Write f32-f127 back to task->thread.fph if it has been modified. */ diff --git a/arch/m68k/include/asm/dma-mapping.h b/arch/m68k/include/asm/dma-mapping.h index 17f7a45948ea..3e6b8445af6a 100644 --- a/arch/m68k/include/asm/dma-mapping.h +++ b/arch/m68k/include/asm/dma-mapping.h @@ -21,6 +21,22 @@ extern void *dma_alloc_coherent(struct device *, size_t, extern void dma_free_coherent(struct device *, size_t, void *, dma_addr_t); +static inline void *dma_alloc_attrs(struct device *dev, size_t size, + dma_addr_t *dma_handle, gfp_t flag, + struct dma_attrs *attrs) +{ + /* attrs is not supported and ignored */ + return dma_alloc_coherent(dev, size, dma_handle, flag); +} + +static inline void dma_free_attrs(struct device *dev, size_t size, + void *cpu_addr, dma_addr_t dma_handle, + struct dma_attrs *attrs) +{ + /* attrs is not supported and ignored */ + dma_free_coherent(dev, size, cpu_addr, dma_handle); +} + static inline void *dma_alloc_noncoherent(struct device *dev, size_t size, dma_addr_t *handle, gfp_t flag) { diff --git a/arch/m68k/include/asm/pgtable_no.h b/arch/m68k/include/asm/pgtable_no.h index bf86b29fe64a..037028f4ab70 100644 --- a/arch/m68k/include/asm/pgtable_no.h +++ b/arch/m68k/include/asm/pgtable_no.h @@ -64,6 +64,8 @@ extern unsigned int kobjsize(const void *objp); */ #define VMALLOC_START 0 #define VMALLOC_END 0xffffffff +#define KMAP_START 0 +#define KMAP_END 0xffffffff #include diff --git a/arch/m68k/include/asm/unistd.h b/arch/m68k/include/asm/unistd.h index 847994ce6804..f9337f614660 100644 --- a/arch/m68k/include/asm/unistd.h +++ b/arch/m68k/include/asm/unistd.h @@ -4,7 +4,7 @@ #include -#define NR_syscalls 348 +#define NR_syscalls 349 #define __ARCH_WANT_OLD_READDIR #define __ARCH_WANT_OLD_STAT diff --git a/arch/m68k/include/uapi/asm/unistd.h b/arch/m68k/include/uapi/asm/unistd.h index b94bfbf90705..625f321001dc 100644 --- a/arch/m68k/include/uapi/asm/unistd.h +++ b/arch/m68k/include/uapi/asm/unistd.h @@ -353,5 +353,6 @@ #define __NR_process_vm_readv 345 #define __NR_process_vm_writev 346 #define __NR_kcmp 347 +#define __NR_finit_module 348 #endif /* _UAPI_ASM_M68K_UNISTD_H_ */ diff --git a/arch/m68k/kernel/syscalltable.S b/arch/m68k/kernel/syscalltable.S index c30da5b3f2db..3f04ea0ab802 100644 --- a/arch/m68k/kernel/syscalltable.S +++ b/arch/m68k/kernel/syscalltable.S @@ -368,4 +368,5 @@ ENTRY(sys_call_table) .long sys_process_vm_readv /* 345 */ .long sys_process_vm_writev .long sys_kcmp + .long sys_finit_module diff --git a/arch/m68k/mm/init.c b/arch/m68k/mm/init.c index f0e05bce92f2..afd8106fd83b 100644 --- a/arch/m68k/mm/init.c +++ b/arch/m68k/mm/init.c @@ -39,6 +39,11 @@ void *empty_zero_page; EXPORT_SYMBOL(empty_zero_page); +#if !defined(CONFIG_SUN3) && !defined(CONFIG_COLDFIRE) +extern void init_pointer_table(unsigned long ptable); +extern pmd_t *zero_pgtable; +#endif + #ifdef CONFIG_MMU pg_data_t pg_data_map[MAX_NUMNODES]; @@ -69,9 +74,6 @@ void __init m68k_setup_node(int node) node_set_online(node); } -extern void init_pointer_table(unsigned long ptable); -extern pmd_t *zero_pgtable; - #else /* CONFIG_MMU */ /* diff --git a/arch/parisc/kernel/entry.S b/arch/parisc/kernel/entry.S index bfb44247d7a7..eb7850b46c25 100644 --- a/arch/parisc/kernel/entry.S +++ b/arch/parisc/kernel/entry.S @@ -1865,7 +1865,7 @@ syscall_restore: /* Are we being ptraced? */ ldw TASK_FLAGS(%r1),%r19 - ldi (_TIF_SINGLESTEP|_TIF_BLOCKSTEP),%r2 + ldi _TIF_SYSCALL_TRACE_MASK,%r2 and,COND(=) %r19,%r2,%r0 b,n syscall_restore_rfi @@ -1978,15 +1978,23 @@ syscall_restore_rfi: /* sr2 should be set to zero for userspace syscalls */ STREG %r0,TASK_PT_SR2(%r1) -pt_regs_ok: LDREG TASK_PT_GR31(%r1),%r2 - depi 3,31,2,%r2 /* ensure return to user mode. */ - STREG %r2,TASK_PT_IAOQ0(%r1) + depi 3,31,2,%r2 /* ensure return to user mode. */ + STREG %r2,TASK_PT_IAOQ0(%r1) ldo 4(%r2),%r2 STREG %r2,TASK_PT_IAOQ1(%r1) - copy %r25,%r16 b intr_restore - nop + copy %r25,%r16 + +pt_regs_ok: + LDREG TASK_PT_IAOQ0(%r1),%r2 + depi 3,31,2,%r2 /* ensure return to user mode. */ + STREG %r2,TASK_PT_IAOQ0(%r1) + LDREG TASK_PT_IAOQ1(%r1),%r2 + depi 3,31,2,%r2 + STREG %r2,TASK_PT_IAOQ1(%r1) + b intr_restore + copy %r25,%r16 .import schedule,code syscall_do_resched: diff --git a/arch/parisc/kernel/irq.c b/arch/parisc/kernel/irq.c index c0b1affc06a8..0299d63cd112 100644 --- a/arch/parisc/kernel/irq.c +++ b/arch/parisc/kernel/irq.c @@ -410,11 +410,13 @@ void __init init_IRQ(void) { local_irq_disable(); /* PARANOID - should already be disabled */ mtctl(~0UL, 23); /* EIRR : clear all pending external intr */ - claim_cpu_irqs(); #ifdef CONFIG_SMP - if (!cpu_eiem) + if (!cpu_eiem) { + claim_cpu_irqs(); cpu_eiem = EIEM_MASK(IPI_IRQ) | EIEM_MASK(TIMER_IRQ); + } #else + claim_cpu_irqs(); cpu_eiem = EIEM_MASK(TIMER_IRQ); #endif set_eiem(cpu_eiem); /* EIEM : enable all external intr */ diff --git a/arch/parisc/kernel/ptrace.c b/arch/parisc/kernel/ptrace.c index 857c2f545470..534abd4936e1 100644 --- a/arch/parisc/kernel/ptrace.c +++ b/arch/parisc/kernel/ptrace.c @@ -26,7 +26,7 @@ #include /* PSW bits we allow the debugger to modify */ -#define USER_PSW_BITS (PSW_N | PSW_V | PSW_CB) +#define USER_PSW_BITS (PSW_N | PSW_B | PSW_V | PSW_CB) /* * Called by kernel/ptrace.c when detaching.. diff --git a/arch/parisc/kernel/signal.c b/arch/parisc/kernel/signal.c index 537996955998..fd051705a407 100644 --- a/arch/parisc/kernel/signal.c +++ b/arch/parisc/kernel/signal.c @@ -190,8 +190,10 @@ get_sigframe(struct k_sigaction *ka, unsigned long sp, size_t frame_size) DBG(1,"get_sigframe: ka = %#lx, sp = %#lx, frame_size = %#lx\n", (unsigned long)ka, sp, frame_size); + /* Align alternate stack and reserve 64 bytes for the signal + handler's frame marker. */ if ((ka->sa.sa_flags & SA_ONSTACK) != 0 && ! sas_ss_flags(sp)) - sp = current->sas_ss_sp; /* Stacks grow up! */ + sp = (current->sas_ss_sp + 0x7f) & ~0x3f; /* Stacks grow up! */ DBG(1,"get_sigframe: Returning sp = %#lx\n", (unsigned long)sp); return (void __user *) sp; /* Stacks grow up. Fun. */ diff --git a/arch/parisc/math-emu/cnv_float.h b/arch/parisc/math-emu/cnv_float.h index 9071e093164a..933423fa5144 100644 --- a/arch/parisc/math-emu/cnv_float.h +++ b/arch/parisc/math-emu/cnv_float.h @@ -347,16 +347,15 @@ Sgl_isinexact_to_fix(sgl_value,exponent) #define Duint_from_sgl_mantissa(sgl_value,exponent,dresultA,dresultB) \ - {Sall(sgl_value) <<= SGL_EXP_LENGTH; /* left-justify */ \ + {unsigned int val = Sall(sgl_value) << SGL_EXP_LENGTH; \ if (exponent <= 31) { \ - Dintp1(dresultA) = 0; \ - Dintp2(dresultB) = (unsigned)Sall(sgl_value) >> (31 - exponent); \ + Dintp1(dresultA) = 0; \ + Dintp2(dresultB) = val >> (31 - exponent); \ } \ else { \ - Dintp1(dresultA) = Sall(sgl_value) >> (63 - exponent); \ - Dintp2(dresultB) = Sall(sgl_value) << (exponent - 31); \ + Dintp1(dresultA) = val >> (63 - exponent); \ + Dintp2(dresultB) = exponent <= 62 ? val << (exponent - 31) : 0; \ } \ - Sall(sgl_value) >>= SGL_EXP_LENGTH; /* return to original */ \ } #define Duint_setzero(dresultA,dresultB) \ diff --git a/arch/powerpc/kernel/entry_32.S b/arch/powerpc/kernel/entry_32.S index d22e73e4618b..e514de57a125 100644 --- a/arch/powerpc/kernel/entry_32.S +++ b/arch/powerpc/kernel/entry_32.S @@ -439,6 +439,8 @@ ret_from_fork: ret_from_kernel_thread: REST_NVGPRS(r1) bl schedule_tail + li r3,0 + stw r3,0(r1) mtlr r14 mr r3,r15 PPC440EP_ERR42 diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index b310a0573625..3d990d3bd8ba 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -664,6 +664,19 @@ resume_kernel: ld r4,TI_FLAGS(r9) andi. r0,r4,_TIF_NEED_RESCHED bne 1b + + /* + * arch_local_irq_restore() from preempt_schedule_irq above may + * enable hard interrupt but we really should disable interrupts + * when we return from the interrupt, and so that we don't get + * interrupted after loading SRR0/1. + */ +#ifdef CONFIG_PPC_BOOK3E + wrteei 0 +#else + ld r10,PACAKMSR(r13) /* Get kernel MSR without EE */ + mtmsrd r10,1 /* Update machine state */ +#endif /* CONFIG_PPC_BOOK3E */ #endif /* CONFIG_PREEMPT */ .globl fast_exc_return_irq diff --git a/arch/powerpc/kernel/kgdb.c b/arch/powerpc/kernel/kgdb.c index c470a40b29f5..a7bc7521c064 100644 --- a/arch/powerpc/kernel/kgdb.c +++ b/arch/powerpc/kernel/kgdb.c @@ -154,12 +154,12 @@ static int kgdb_handle_breakpoint(struct pt_regs *regs) static int kgdb_singlestep(struct pt_regs *regs) { struct thread_info *thread_info, *exception_thread_info; - struct thread_info *backup_current_thread_info = \ - (struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL); + struct thread_info *backup_current_thread_info; if (user_mode(regs)) return 0; + backup_current_thread_info = (struct thread_info *)kmalloc(sizeof(struct thread_info), GFP_KERNEL); /* * On Book E and perhaps other processors, singlestep is handled on * the critical exception stack. This causes current_thread_info() @@ -185,6 +185,7 @@ static int kgdb_singlestep(struct pt_regs *regs) /* Restore current_thread_info lastly. */ memcpy(exception_thread_info, backup_current_thread_info, sizeof *thread_info); + kfree(backup_current_thread_info); return 1; } diff --git a/arch/powerpc/kernel/time.c b/arch/powerpc/kernel/time.c index 6f6b1cccc916..127361e093f4 100644 --- a/arch/powerpc/kernel/time.c +++ b/arch/powerpc/kernel/time.c @@ -494,10 +494,15 @@ void timer_interrupt(struct pt_regs * regs) set_dec(DECREMENTER_MAX); /* Some implementations of hotplug will get timer interrupts while - * offline, just ignore these + * offline, just ignore these and we also need to set + * decrementers_next_tb as MAX to make sure __check_irq_replay + * don't replay timer interrupt when return, otherwise we'll trap + * here infinitely :( */ - if (!cpu_online(smp_processor_id())) + if (!cpu_online(smp_processor_id())) { + *next_tb = ~(u64)0; return; + } /* Conditionally hard-enable interrupts now that the DEC has been * bumped to its maximum value diff --git a/arch/powerpc/kvm/emulate.c b/arch/powerpc/kvm/emulate.c index b0855e5d8905..9d9cddc5b346 100644 --- a/arch/powerpc/kvm/emulate.c +++ b/arch/powerpc/kvm/emulate.c @@ -39,6 +39,7 @@ #define OP_31_XOP_TRAP 4 #define OP_31_XOP_LWZX 23 #define OP_31_XOP_TRAP_64 68 +#define OP_31_XOP_DCBF 86 #define OP_31_XOP_LBZX 87 #define OP_31_XOP_STWX 151 #define OP_31_XOP_STBX 215 @@ -374,6 +375,7 @@ int kvmppc_emulate_instruction(struct kvm_run *run, struct kvm_vcpu *vcpu) emulated = kvmppc_emulate_mtspr(vcpu, sprn, rs); break; + case OP_31_XOP_DCBF: case OP_31_XOP_DCBI: /* Do nothing. The guest is performing dcbi because * hardware DMA is not snooped by the dcache, but diff --git a/arch/powerpc/oprofile/op_model_power4.c b/arch/powerpc/oprofile/op_model_power4.c index 315f9495e9b2..f444b94935f5 100644 --- a/arch/powerpc/oprofile/op_model_power4.c +++ b/arch/powerpc/oprofile/op_model_power4.c @@ -52,7 +52,7 @@ static int power7_marked_instr_event(u64 mmcr1) for (pmc = 0; pmc < 4; pmc++) { psel = mmcr1 & (OPROFILE_PM_PMCSEL_MSK << (OPROFILE_MAX_PMC_NUM - pmc) - * OPROFILE_MAX_PMC_NUM); + * OPROFILE_PMSEL_FIELD_WIDTH); psel = (psel >> ((OPROFILE_MAX_PMC_NUM - pmc) * OPROFILE_PMSEL_FIELD_WIDTH)) & ~1ULL; unit = mmcr1 & (OPROFILE_PM_UNIT_MSK diff --git a/arch/powerpc/platforms/pasemi/cpufreq.c b/arch/powerpc/platforms/pasemi/cpufreq.c index 95d00173029f..890f30e70f98 100644 --- a/arch/powerpc/platforms/pasemi/cpufreq.c +++ b/arch/powerpc/platforms/pasemi/cpufreq.c @@ -236,6 +236,13 @@ out: static int pas_cpufreq_cpu_exit(struct cpufreq_policy *policy) { + /* + * We don't support CPU hotplug. Don't unmap after the system + * has already made it to a running state. + */ + if (system_state != SYSTEM_BOOTING) + return 0; + if (sdcasr_mapbase) iounmap(sdcasr_mapbase); if (sdcpwr_mapbase) diff --git a/arch/s390/include/asm/pgtable.h b/arch/s390/include/asm/pgtable.h index c1d7930a82f4..098adbb62660 100644 --- a/arch/s390/include/asm/pgtable.h +++ b/arch/s390/include/asm/pgtable.h @@ -1365,6 +1365,18 @@ static inline void pmdp_invalidate(struct vm_area_struct *vma, __pmd_idte(address, pmdp); } +#define __HAVE_ARCH_PMDP_SET_WRPROTECT +static inline void pmdp_set_wrprotect(struct mm_struct *mm, + unsigned long address, pmd_t *pmdp) +{ + pmd_t pmd = *pmdp; + + if (pmd_write(pmd)) { + __pmd_idte(address, pmdp); + set_pmd_at(mm, address, pmdp, pmd_wrprotect(pmd)); + } +} + static inline pmd_t mk_pmd_phys(unsigned long physpage, pgprot_t pgprot) { pmd_t __pmd; diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 79795af59810..225543bf45a5 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -2138,6 +2138,7 @@ config OLPC_XO1_RTC config OLPC_XO1_SCI bool "OLPC XO-1 SCI extras" depends on OLPC && OLPC_XO1_PM + depends on INPUT=y select POWER_SUPPLY select GPIO_CS5535 select MFD_CORE diff --git a/arch/x86/boot/Makefile b/arch/x86/boot/Makefile index ccce0ed67dde..379814bc41e3 100644 --- a/arch/x86/boot/Makefile +++ b/arch/x86/boot/Makefile @@ -71,7 +71,7 @@ GCOV_PROFILE := n $(obj)/bzImage: asflags-y := $(SVGA_MODE) quiet_cmd_image = BUILD $@ -cmd_image = $(obj)/tools/build $(obj)/setup.bin $(obj)/vmlinux.bin > $@ +cmd_image = $(obj)/tools/build $(obj)/setup.bin $(obj)/vmlinux.bin $(obj)/zoffset.h > $@ $(obj)/bzImage: $(obj)/setup.bin $(obj)/vmlinux.bin $(obj)/tools/build FORCE $(call if_changed,image) @@ -92,7 +92,7 @@ targets += voffset.h $(obj)/voffset.h: vmlinux FORCE $(call if_changed,voffset) -sed-zoffset := -e 's/^\([0-9a-fA-F]*\) . \(startup_32\|input_data\|_end\|z_.*\)$$/\#define ZO_\2 0x\1/p' +sed-zoffset := -e 's/^\([0-9a-fA-F]*\) . \(startup_32\|startup_64\|efi_pe_entry\|efi_stub_entry\|input_data\|_end\|z_.*\)$$/\#define ZO_\2 0x\1/p' quiet_cmd_zoffset = ZOFFSET $@ cmd_zoffset = $(NM) $< | sed -n $(sed-zoffset) > $@ diff --git a/arch/x86/boot/compressed/eboot.c b/arch/x86/boot/compressed/eboot.c index 18e329ca108e..f8fa41190c35 100644 --- a/arch/x86/boot/compressed/eboot.c +++ b/arch/x86/boot/compressed/eboot.c @@ -256,10 +256,10 @@ static efi_status_t setup_efi_pci(struct boot_params *params) int i; struct setup_data *data; - data = (struct setup_data *)params->hdr.setup_data; + data = (struct setup_data *)(unsigned long)params->hdr.setup_data; while (data && data->next) - data = (struct setup_data *)data->next; + data = (struct setup_data *)(unsigned long)data->next; status = efi_call_phys5(sys_table->boottime->locate_handle, EFI_LOCATE_BY_PROTOCOL, &pci_proto, @@ -295,16 +295,18 @@ static efi_status_t setup_efi_pci(struct boot_params *params) if (!pci) continue; +#ifdef CONFIG_X86_64 status = efi_call_phys4(pci->attributes, pci, EfiPciIoAttributeOperationGet, 0, &attributes); - +#else + status = efi_call_phys5(pci->attributes, pci, + EfiPciIoAttributeOperationGet, 0, 0, + &attributes); +#endif if (status != EFI_SUCCESS) continue; - if (!(attributes & EFI_PCI_IO_ATTRIBUTE_EMBEDDED_ROM)) - continue; - if (!pci->romimage || !pci->romsize) continue; @@ -345,9 +347,9 @@ static efi_status_t setup_efi_pci(struct boot_params *params) memcpy(rom->romdata, pci->romimage, pci->romsize); if (data) - data->next = (uint64_t)rom; + data->next = (unsigned long)rom; else - params->hdr.setup_data = (uint64_t)rom; + params->hdr.setup_data = (unsigned long)rom; data = (struct setup_data *)rom; @@ -432,10 +434,9 @@ static efi_status_t setup_gop(struct screen_info *si, efi_guid_t *proto, * Once we've found a GOP supporting ConOut, * don't bother looking any further. */ + first_gop = gop; if (conout_found) break; - - first_gop = gop; } } diff --git a/arch/x86/boot/compressed/head_32.S b/arch/x86/boot/compressed/head_32.S index aa4aaf1b2380..1e3184f6072f 100644 --- a/arch/x86/boot/compressed/head_32.S +++ b/arch/x86/boot/compressed/head_32.S @@ -35,11 +35,11 @@ ENTRY(startup_32) #ifdef CONFIG_EFI_STUB jmp preferred_addr - .balign 0x10 /* * We don't need the return address, so set up the stack so - * efi_main() can find its arugments. + * efi_main() can find its arguments. */ +ENTRY(efi_pe_entry) add $0x4, %esp call make_boot_params @@ -50,8 +50,10 @@ ENTRY(startup_32) pushl %eax pushl %esi pushl %ecx + sub $0x4, %esp - .org 0x30,0x90 +ENTRY(efi_stub_entry) + add $0x4, %esp call efi_main cmpl $0, %eax movl %eax, %esi diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S index 2c4b171eec33..f5d1aaa0dec8 100644 --- a/arch/x86/boot/compressed/head_64.S +++ b/arch/x86/boot/compressed/head_64.S @@ -201,12 +201,12 @@ ENTRY(startup_64) */ #ifdef CONFIG_EFI_STUB /* - * The entry point for the PE/COFF executable is 0x210, so only - * legacy boot loaders will execute this jmp. + * The entry point for the PE/COFF executable is efi_pe_entry, so + * only legacy boot loaders will execute this jmp. */ jmp preferred_addr - .org 0x210 +ENTRY(efi_pe_entry) mov %rcx, %rdi mov %rdx, %rsi pushq %rdi @@ -218,7 +218,7 @@ ENTRY(startup_64) popq %rsi popq %rdi - .org 0x230,0x90 +ENTRY(efi_stub_entry) call efi_main movq %rax,%rsi cmpq $0,%rax diff --git a/arch/x86/boot/header.S b/arch/x86/boot/header.S index 8c132a625b94..944ce595f767 100644 --- a/arch/x86/boot/header.S +++ b/arch/x86/boot/header.S @@ -21,6 +21,7 @@ #include #include #include +#include #include "boot.h" #include "voffset.h" #include "zoffset.h" @@ -255,6 +256,9 @@ section_table: # header, from the old boot sector. .section ".header", "a" + .globl sentinel +sentinel: .byte 0xff, 0xff /* Used to detect broken loaders */ + .globl hdr hdr: setup_sects: .byte 0 /* Filled in by build.c */ @@ -279,7 +283,7 @@ _start: # Part 2 of the header, from the old setup.S .ascii "HdrS" # header signature - .word 0x020b # header version number (>= 0x0105) + .word 0x020c # header version number (>= 0x0105) # or else old loadlin-1.5 will fail) .globl realmode_swtch realmode_swtch: .word 0, 0 # default_switch, SETUPSEG @@ -297,13 +301,7 @@ type_of_loader: .byte 0 # 0 means ancient bootloader, newer # flags, unused bits must be zero (RFU) bit within loadflags loadflags: -LOADED_HIGH = 1 # If set, the kernel is loaded high -CAN_USE_HEAP = 0x80 # If set, the loader also has set - # heap_end_ptr to tell how much - # space behind setup.S can be used for - # heap purposes. - # Only the loader knows what is free - .byte LOADED_HIGH + .byte LOADED_HIGH # The kernel is to be loaded high setup_move_size: .word 0x8000 # size to move, when setup is not # loaded at 0x90000. We will move setup @@ -369,7 +367,23 @@ relocatable_kernel: .byte 1 relocatable_kernel: .byte 0 #endif min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment -pad3: .word 0 + +xloadflags: +#ifdef CONFIG_X86_64 +# define XLF0 XLF_KERNEL_64 /* 64-bit kernel */ +#else +# define XLF0 0 +#endif +#ifdef CONFIG_EFI_STUB +# ifdef CONFIG_X86_64 +# define XLF23 XLF_EFI_HANDOVER_64 /* 64-bit EFI handover ok */ +# else +# define XLF23 XLF_EFI_HANDOVER_32 /* 32-bit EFI handover ok */ +# endif +#else +# define XLF23 0 +#endif + .word XLF0 | XLF23 cmdline_size: .long COMMAND_LINE_SIZE-1 #length of the command line, #added with boot protocol @@ -397,8 +411,13 @@ pref_address: .quad LOAD_PHYSICAL_ADDR # preferred load addr #define INIT_SIZE VO_INIT_SIZE #endif init_size: .long INIT_SIZE # kernel initialization size -handover_offset: .long 0x30 # offset to the handover +handover_offset: +#ifdef CONFIG_EFI_STUB + .long 0x30 # offset to the handover # protocol entry point +#else + .long 0 +#endif # End of setup header ##################################################### diff --git a/arch/x86/boot/setup.ld b/arch/x86/boot/setup.ld index 03c0683636b6..96a6c7563538 100644 --- a/arch/x86/boot/setup.ld +++ b/arch/x86/boot/setup.ld @@ -13,7 +13,7 @@ SECTIONS .bstext : { *(.bstext) } .bsdata : { *(.bsdata) } - . = 497; + . = 495; .header : { *(.header) } .entrytext : { *(.entrytext) } .inittext : { *(.inittext) } diff --git a/arch/x86/boot/tools/build.c b/arch/x86/boot/tools/build.c index 4b8e165ee572..94c544650020 100644 --- a/arch/x86/boot/tools/build.c +++ b/arch/x86/boot/tools/build.c @@ -52,6 +52,10 @@ int is_big_kernel; #define PECOFF_RELOC_RESERVE 0x20 +unsigned long efi_stub_entry; +unsigned long efi_pe_entry; +unsigned long startup_64; + /*----------------------------------------------------------------------*/ static const u32 crctab32[] = { @@ -132,7 +136,7 @@ static void die(const char * str, ...) static void usage(void) { - die("Usage: build setup system [> image]"); + die("Usage: build setup system [zoffset.h] [> image]"); } #ifdef CONFIG_EFI_STUB @@ -206,30 +210,54 @@ static void update_pecoff_text(unsigned int text_start, unsigned int file_sz) */ put_unaligned_le32(file_sz - 512, &buf[pe_header + 0x1c]); -#ifdef CONFIG_X86_32 /* - * Address of entry point. - * - * The EFI stub entry point is +16 bytes from the start of - * the .text section. + * Address of entry point for PE/COFF executable */ - put_unaligned_le32(text_start + 16, &buf[pe_header + 0x28]); -#else - /* - * Address of entry point. startup_32 is at the beginning and - * the 64-bit entry point (startup_64) is always 512 bytes - * after. The EFI stub entry point is 16 bytes after that, as - * the first instruction allows legacy loaders to jump over - * the EFI stub initialisation - */ - put_unaligned_le32(text_start + 528, &buf[pe_header + 0x28]); -#endif /* CONFIG_X86_32 */ + put_unaligned_le32(text_start + efi_pe_entry, &buf[pe_header + 0x28]); update_pecoff_section_header(".text", text_start, text_sz); } #endif /* CONFIG_EFI_STUB */ + +/* + * Parse zoffset.h and find the entry points. We could just #include zoffset.h + * but that would mean tools/build would have to be rebuilt every time. It's + * not as if parsing it is hard... + */ +#define PARSE_ZOFS(p, sym) do { \ + if (!strncmp(p, "#define ZO_" #sym " ", 11+sizeof(#sym))) \ + sym = strtoul(p + 11 + sizeof(#sym), NULL, 16); \ +} while (0) + +static void parse_zoffset(char *fname) +{ + FILE *file; + char *p; + int c; + + file = fopen(fname, "r"); + if (!file) + die("Unable to open `%s': %m", fname); + c = fread(buf, 1, sizeof(buf) - 1, file); + if (ferror(file)) + die("read-error on `zoffset.h'"); + buf[c] = 0; + + p = (char *)buf; + + while (p && *p) { + PARSE_ZOFS(p, efi_stub_entry); + PARSE_ZOFS(p, efi_pe_entry); + PARSE_ZOFS(p, startup_64); + + p = strchr(p, '\n'); + while (p && (*p == '\r' || *p == '\n')) + p++; + } +} + int main(int argc, char ** argv) { unsigned int i, sz, setup_sectors; @@ -241,7 +269,19 @@ int main(int argc, char ** argv) void *kernel; u32 crc = 0xffffffffUL; - if (argc != 3) + /* Defaults for old kernel */ +#ifdef CONFIG_X86_32 + efi_pe_entry = 0x10; + efi_stub_entry = 0x30; +#else + efi_pe_entry = 0x210; + efi_stub_entry = 0x230; + startup_64 = 0x200; +#endif + + if (argc == 4) + parse_zoffset(argv[3]); + else if (argc != 3) usage(); /* Copy the setup code */ @@ -299,6 +339,11 @@ int main(int argc, char ** argv) #ifdef CONFIG_EFI_STUB update_pecoff_text(setup_sectors * 512, sz + i + ((sys_size * 16) - sz)); + +#ifdef CONFIG_X86_64 /* Yes, this is really how we defined it :( */ + efi_stub_entry -= 0x200; +#endif + put_unaligned_le32(efi_stub_entry, &buf[0x264]); #endif crc = partial_crc32(buf, i, crc); diff --git a/arch/x86/include/asm/efi.h b/arch/x86/include/asm/efi.h index 6e8fdf5ad113..28677c55113f 100644 --- a/arch/x86/include/asm/efi.h +++ b/arch/x86/include/asm/efi.h @@ -94,6 +94,7 @@ extern void __iomem *efi_ioremap(unsigned long addr, unsigned long size, #endif /* CONFIG_X86_32 */ extern int add_efi_memmap; +extern unsigned long x86_efi_facility; extern void efi_set_executable(efi_memory_desc_t *md, bool executable); extern int efi_memblock_x86_reserve_range(void); extern void efi_call_phys_prelog(void); diff --git a/arch/x86/include/asm/uv/uv.h b/arch/x86/include/asm/uv/uv.h index b47c2a82ff15..062921ef34e9 100644 --- a/arch/x86/include/asm/uv/uv.h +++ b/arch/x86/include/asm/uv/uv.h @@ -16,7 +16,7 @@ extern void uv_system_init(void); extern const struct cpumask *uv_flush_tlb_others(const struct cpumask *cpumask, struct mm_struct *mm, unsigned long start, - unsigned end, + unsigned long end, unsigned int cpu); #else /* X86_UV */ diff --git a/arch/x86/include/uapi/asm/bootparam.h b/arch/x86/include/uapi/asm/bootparam.h index 92862cd90201..c15ddaf90710 100644 --- a/arch/x86/include/uapi/asm/bootparam.h +++ b/arch/x86/include/uapi/asm/bootparam.h @@ -1,6 +1,31 @@ #ifndef _ASM_X86_BOOTPARAM_H #define _ASM_X86_BOOTPARAM_H +/* setup_data types */ +#define SETUP_NONE 0 +#define SETUP_E820_EXT 1 +#define SETUP_DTB 2 +#define SETUP_PCI 3 + +/* ram_size flags */ +#define RAMDISK_IMAGE_START_MASK 0x07FF +#define RAMDISK_PROMPT_FLAG 0x8000 +#define RAMDISK_LOAD_FLAG 0x4000 + +/* loadflags */ +#define LOADED_HIGH (1<<0) +#define QUIET_FLAG (1<<5) +#define KEEP_SEGMENTS (1<<6) +#define CAN_USE_HEAP (1<<7) + +/* xloadflags */ +#define XLF_KERNEL_64 (1<<0) +#define XLF_CAN_BE_LOADED_ABOVE_4G (1<<1) +#define XLF_EFI_HANDOVER_32 (1<<2) +#define XLF_EFI_HANDOVER_64 (1<<3) + +#ifndef __ASSEMBLY__ + #include #include #include @@ -9,12 +34,6 @@ #include #include