diff --git a/drivers/clk/tegra/clk-dfll.c b/drivers/clk/tegra/clk-dfll.c index 609e363dabf8..69bbf62a9eab 100644 --- a/drivers/clk/tegra/clk-dfll.c +++ b/drivers/clk/tegra/clk-dfll.c @@ -1,7 +1,7 @@ /* * clk-dfll.c - Tegra DFLL clock source common code * - * Copyright (C) 2012-2014 NVIDIA Corporation. All rights reserved. + * Copyright (C) 2012-2019 NVIDIA Corporation. All rights reserved. * * Aleksandr Frid * Paul Walmsley @@ -47,6 +47,7 @@ #include #include #include +#include #include #include #include @@ -243,6 +244,12 @@ enum dfll_tune_range { DFLL_TUNE_LOW = 1, }; + +enum tegra_dfll_pmu_if { + TEGRA_DFLL_PMU_I2C = 0, + TEGRA_DFLL_PMU_PWM = 1, +}; + /** * struct dfll_rate_req - target DFLL rate request data * @rate: target frequency, after the postscaling @@ -300,10 +307,19 @@ struct tegra_dfll { u32 i2c_reg; u32 i2c_slave_addr; - /* i2c_lut array entries are regulator framework selectors */ - unsigned i2c_lut[MAX_DFLL_VOLTAGES]; - int i2c_lut_size; - u8 lut_min, lut_max, lut_safe; + /* lut array entries are regulator framework selectors or PWM values*/ + unsigned lut[MAX_DFLL_VOLTAGES]; + unsigned long lut_uv[MAX_DFLL_VOLTAGES]; + int lut_size; + u8 lut_bottom, lut_min, lut_max, lut_safe; + + /* PWM interface */ + enum tegra_dfll_pmu_if pmu_if; + unsigned long pwm_rate; + struct pinctrl *pwm_pin; + struct pinctrl_state *pwm_enable_state; + struct pinctrl_state *pwm_disable_state; + u32 reg_init_uV; }; #define clk_hw_to_dfll(_hw) container_of(_hw, struct tegra_dfll, dfll_clk_hw) @@ -489,6 +505,34 @@ static void dfll_set_mode(struct tegra_dfll *td, dfll_wmb(td); } +/* + * DVCO rate control + */ + +static unsigned long get_dvco_rate_below(struct tegra_dfll *td, u8 out_min) +{ + struct dev_pm_opp *opp; + unsigned long rate, prev_rate; + unsigned long uv, min_uv; + + min_uv = td->lut_uv[out_min]; + for (rate = 0, prev_rate = 0; ; rate++) { + opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate); + if (IS_ERR(opp)) + break; + + uv = dev_pm_opp_get_voltage(opp); + dev_pm_opp_put(opp); + + if (uv && uv > min_uv) + return prev_rate; + + prev_rate = rate; + } + + return prev_rate; +} + /* * DFLL-to-I2C controller interface */ @@ -518,6 +562,118 @@ static int dfll_i2c_set_output_enabled(struct tegra_dfll *td, bool enable) return 0; } + +/* + * DFLL-to-PWM controller interface + */ + +/** + * dfll_pwm_set_output_enabled - enable/disable PWM voltage requests + * @td: DFLL instance + * @enable: whether to enable or disable the PWM voltage requests + * + * Set the master enable control for PWM control value updates. If disabled, + * then the PWM signal is not driven. Also configure the PWM output pad + * to the appropriate state. + */ +static int dfll_pwm_set_output_enabled(struct tegra_dfll *td, bool enable) +{ + int ret; + u32 val, div; + + if (enable) { + ret = pinctrl_select_state(td->pwm_pin, td->pwm_enable_state); + if (ret < 0) { + dev_err(td->dev, "setting enable state failed\n"); + return -EINVAL; + } + val = dfll_readl(td, DFLL_OUTPUT_CFG); + val &= ~DFLL_OUTPUT_CFG_PWM_DIV_MASK; + div = DIV_ROUND_UP(td->ref_rate, td->pwm_rate); + val |= (div << DFLL_OUTPUT_CFG_PWM_DIV_SHIFT) + & DFLL_OUTPUT_CFG_PWM_DIV_MASK; + dfll_writel(td, val, DFLL_OUTPUT_CFG); + dfll_wmb(td); + + val |= DFLL_OUTPUT_CFG_PWM_ENABLE; + dfll_writel(td, val, DFLL_OUTPUT_CFG); + dfll_wmb(td); + } else { + ret = pinctrl_select_state(td->pwm_pin, td->pwm_disable_state); + if (ret < 0) + dev_warn(td->dev, "setting disable state failed\n"); + + val = dfll_readl(td, DFLL_OUTPUT_CFG); + val &= ~DFLL_OUTPUT_CFG_PWM_ENABLE; + dfll_writel(td, val, DFLL_OUTPUT_CFG); + dfll_wmb(td); + } + + return 0; +} + +/** + * dfll_set_force_output_value - set fixed value for force output + * @td: DFLL instance + * @out_val: value to force output + * + * Set the fixed value for force output, DFLL will output this value when + * force output is enabled. + */ +static u32 dfll_set_force_output_value(struct tegra_dfll *td, u8 out_val) +{ + u32 val = dfll_readl(td, DFLL_OUTPUT_FORCE); + + val = (val & DFLL_OUTPUT_FORCE_ENABLE) | (out_val & OUT_MASK); + dfll_writel(td, val, DFLL_OUTPUT_FORCE); + dfll_wmb(td); + + return dfll_readl(td, DFLL_OUTPUT_FORCE); +} + +/** + * dfll_set_force_output_enabled - enable/disable force output + * @td: DFLL instance + * @enable: whether to enable or disable the force output + * + * Set the enable control for fouce output with fixed value. + */ +static void dfll_set_force_output_enabled(struct tegra_dfll *td, bool enable) +{ + u32 val = dfll_readl(td, DFLL_OUTPUT_FORCE); + + if (enable) + val |= DFLL_OUTPUT_FORCE_ENABLE; + else + val &= ~DFLL_OUTPUT_FORCE_ENABLE; + + dfll_writel(td, val, DFLL_OUTPUT_FORCE); + dfll_wmb(td); +} + +/** + * dfll_force_output - force output a fixed value + * @td: DFLL instance + * @out_sel: value to force output + * + * Set the fixed value for force output, DFLL will output this value. + */ +static int dfll_force_output(struct tegra_dfll *td, unsigned int out_sel) +{ + u32 val; + + if (out_sel > OUT_MASK) + return -EINVAL; + + val = dfll_set_force_output_value(td, out_sel); + if ((td->mode < DFLL_CLOSED_LOOP) && + !(val & DFLL_OUTPUT_FORCE_ENABLE)) { + dfll_set_force_output_enabled(td, true); + } + + return 0; +} + /** * dfll_load_lut - load the voltage lookup table * @td: struct tegra_dfll * @@ -539,7 +695,7 @@ static void dfll_load_i2c_lut(struct tegra_dfll *td) lut_index = i; val = regulator_list_hardware_vsel(td->vdd_reg, - td->i2c_lut[lut_index]); + td->lut[lut_index]); __raw_writel(val, td->lut_base + i * 4); } @@ -594,24 +750,41 @@ static void dfll_init_out_if(struct tegra_dfll *td) { u32 val; - td->lut_min = 0; - td->lut_max = td->i2c_lut_size - 1; - td->lut_safe = td->lut_min + 1; + td->lut_min = td->lut_bottom; + td->lut_max = td->lut_size - 1; + td->lut_safe = td->lut_min + (td->lut_min < td->lut_max ? 1 : 0); + + /* clear DFLL_OUTPUT_CFG before setting new value */ + dfll_writel(td, 0, DFLL_OUTPUT_CFG); + dfll_wmb(td); - dfll_i2c_writel(td, 0, DFLL_OUTPUT_CFG); val = (td->lut_safe << DFLL_OUTPUT_CFG_SAFE_SHIFT) | - (td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) | - (td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT); - dfll_i2c_writel(td, val, DFLL_OUTPUT_CFG); - dfll_i2c_wmb(td); + (td->lut_max << DFLL_OUTPUT_CFG_MAX_SHIFT) | + (td->lut_min << DFLL_OUTPUT_CFG_MIN_SHIFT); + dfll_writel(td, val, DFLL_OUTPUT_CFG); + dfll_wmb(td); dfll_writel(td, 0, DFLL_OUTPUT_FORCE); dfll_i2c_writel(td, 0, DFLL_INTR_EN); dfll_i2c_writel(td, DFLL_INTR_MAX_MASK | DFLL_INTR_MIN_MASK, DFLL_INTR_STS); - dfll_load_i2c_lut(td); - dfll_init_i2c_if(td); + if (td->pmu_if == TEGRA_DFLL_PMU_PWM) { + u32 vinit = td->reg_init_uV; + int vstep = td->soc->alignment.step_uv; + unsigned long vmin = td->lut_uv[0]; + + /* set initial voltage */ + if ((vinit >= vmin) && vstep) { + unsigned int vsel; + + vsel = DIV_ROUND_UP((vinit - vmin), vstep); + dfll_force_output(td, vsel); + } + } else { + dfll_load_i2c_lut(td); + dfll_init_i2c_if(td); + } } /* @@ -631,7 +804,8 @@ static void dfll_init_out_if(struct tegra_dfll *td) static int find_lut_index_for_rate(struct tegra_dfll *td, unsigned long rate) { struct dev_pm_opp *opp; - int i, uv; + unsigned long uv; + int i; opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate); if (IS_ERR(opp)) @@ -640,8 +814,8 @@ static int find_lut_index_for_rate(struct tegra_dfll *td, unsigned long rate) uv = dev_pm_opp_get_voltage(opp); dev_pm_opp_put(opp); - for (i = 0; i < td->i2c_lut_size; i++) { - if (regulator_list_voltage(td->vdd_reg, td->i2c_lut[i]) == uv) + for (i = td->lut_bottom; i < td->lut_size; i++) { + if (td->lut_uv[i] >= uv) return i; } @@ -863,9 +1037,14 @@ static int dfll_lock(struct tegra_dfll *td) return -EINVAL; } - dfll_i2c_set_output_enabled(td, true); + if (td->pmu_if == TEGRA_DFLL_PMU_PWM) + dfll_pwm_set_output_enabled(td, true); + else + dfll_i2c_set_output_enabled(td, true); + dfll_set_mode(td, DFLL_CLOSED_LOOP); dfll_set_frequency_request(td, req); + dfll_set_force_output_enabled(td, false); return 0; default: @@ -889,7 +1068,10 @@ static int dfll_unlock(struct tegra_dfll *td) case DFLL_CLOSED_LOOP: dfll_set_open_loop_config(td); dfll_set_mode(td, DFLL_OPEN_LOOP); - dfll_i2c_set_output_enabled(td, false); + if (td->pmu_if == TEGRA_DFLL_PMU_PWM) + dfll_pwm_set_output_enabled(td, false); + else + dfll_i2c_set_output_enabled(td, false); return 0; case DFLL_OPEN_LOOP: @@ -1171,15 +1353,17 @@ static int attr_registers_show(struct seq_file *s, void *data) seq_printf(s, "[0x%02x] = 0x%08x\n", offs, dfll_i2c_readl(td, offs)); - seq_puts(s, "\nINTEGRATED I2C CONTROLLER REGISTERS:\n"); - offs = DFLL_I2C_CLK_DIVISOR; - seq_printf(s, "[0x%02x] = 0x%08x\n", offs, - __raw_readl(td->i2c_controller_base + offs)); - - seq_puts(s, "\nLUT:\n"); - for (offs = 0; offs < 4 * MAX_DFLL_VOLTAGES; offs += 4) + if (td->pmu_if == TEGRA_DFLL_PMU_I2C) { + seq_puts(s, "\nINTEGRATED I2C CONTROLLER REGISTERS:\n"); + offs = DFLL_I2C_CLK_DIVISOR; seq_printf(s, "[0x%02x] = 0x%08x\n", offs, - __raw_readl(td->lut_base + offs)); + __raw_readl(td->i2c_controller_base + offs)); + + seq_puts(s, "\nLUT:\n"); + for (offs = 0; offs < 4 * MAX_DFLL_VOLTAGES; offs += 4) + seq_printf(s, "[0x%02x] = 0x%08x\n", offs, + __raw_readl(td->lut_base + offs)); + } return 0; } @@ -1351,6 +1535,9 @@ static int find_vdd_map_entry_exact(struct tegra_dfll *td, int uV) { int i, n_voltages, reg_uV; + if (WARN_ON(td->pmu_if == TEGRA_DFLL_PMU_PWM)) + return -EINVAL; + n_voltages = regulator_count_voltages(td->vdd_reg); for (i = 0; i < n_voltages; i++) { reg_uV = regulator_list_voltage(td->vdd_reg, i); @@ -1373,6 +1560,9 @@ static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV) { int i, n_voltages, reg_uV; + if (WARN_ON(td->pmu_if == TEGRA_DFLL_PMU_PWM)) + return -EINVAL; + n_voltages = regulator_count_voltages(td->vdd_reg); for (i = 0; i < n_voltages; i++) { reg_uV = regulator_list_voltage(td->vdd_reg, i); @@ -1387,9 +1577,61 @@ static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV) return -EINVAL; } +/* + * dfll_build_pwm_lut - build the PWM regulator lookup table + * @td: DFLL instance + * @v_max: Vmax from OPP table + * + * Look-up table in h/w is ignored when PWM is used as DFLL interface to PMIC. + * In this case closed loop output is controlling duty cycle directly. The s/w + * look-up that maps PWM duty cycle to voltage is still built by this function. + */ +static int dfll_build_pwm_lut(struct tegra_dfll *td, unsigned long v_max) +{ + int i; + unsigned long rate, reg_volt; + u8 lut_bottom = MAX_DFLL_VOLTAGES; + int v_min = td->soc->cvb->min_millivolts * 1000; + + for (i = 0; i < MAX_DFLL_VOLTAGES; i++) { + reg_volt = td->lut_uv[i]; + + /* since opp voltage is exact mv */ + reg_volt = (reg_volt / 1000) * 1000; + if (reg_volt > v_max) + break; + + td->lut[i] = i; + if ((lut_bottom == MAX_DFLL_VOLTAGES) && (reg_volt >= v_min)) + lut_bottom = i; + } + + /* determine voltage boundaries */ + td->lut_size = i; + if ((lut_bottom == MAX_DFLL_VOLTAGES) || + (lut_bottom + 1 >= td->lut_size)) { + dev_err(td->dev, "no voltage above DFLL minimum %d mV\n", + td->soc->cvb->min_millivolts); + return -EINVAL; + } + td->lut_bottom = lut_bottom; + + /* determine rate boundaries */ + rate = get_dvco_rate_below(td, td->lut_bottom); + if (!rate) { + dev_err(td->dev, "no opp below DFLL minimum voltage %d mV\n", + td->soc->cvb->min_millivolts); + return -EINVAL; + } + td->dvco_rate_min = rate; + + return 0; +} + /** * dfll_build_i2c_lut - build the I2C voltage register lookup table * @td: DFLL instance + * @v_max: Vmax from OPP table * * The DFLL hardware has 33 bytes of look-up table RAM that must be filled with * PMIC voltage register values that span the entire DFLL operating range. @@ -1397,33 +1639,24 @@ static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV) * the soc-specific platform driver (td->soc->opp_dev) and the PMIC * register-to-voltage mapping queried from the regulator framework. * - * On success, fills in td->i2c_lut and returns 0, or -err on failure. + * On success, fills in td->lut and returns 0, or -err on failure. */ -static int dfll_build_i2c_lut(struct tegra_dfll *td) +static int dfll_build_i2c_lut(struct tegra_dfll *td, unsigned long v_max) { + unsigned long rate, v, v_opp; int ret = -EINVAL; - int j, v, v_max, v_opp; - int selector; - unsigned long rate; - struct dev_pm_opp *opp; - int lut; - - rate = ULONG_MAX; - opp = dev_pm_opp_find_freq_floor(td->soc->dev, &rate); - if (IS_ERR(opp)) { - dev_err(td->dev, "couldn't get vmax opp, empty opp table?\n"); - goto out; - } - v_max = dev_pm_opp_get_voltage(opp); - dev_pm_opp_put(opp); + int j, selector, lut; v = td->soc->cvb->min_millivolts * 1000; lut = find_vdd_map_entry_exact(td, v); if (lut < 0) goto out; - td->i2c_lut[0] = lut; + td->lut[0] = lut; + td->lut_bottom = 0; for (j = 1, rate = 0; ; rate++) { + struct dev_pm_opp *opp; + opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate); if (IS_ERR(opp)) break; @@ -1435,39 +1668,64 @@ static int dfll_build_i2c_lut(struct tegra_dfll *td) dev_pm_opp_put(opp); for (;;) { - v += max(1, (v_max - v) / (MAX_DFLL_VOLTAGES - j)); + v += max(1UL, (v_max - v) / (MAX_DFLL_VOLTAGES - j)); if (v >= v_opp) break; selector = find_vdd_map_entry_min(td, v); if (selector < 0) goto out; - if (selector != td->i2c_lut[j - 1]) - td->i2c_lut[j++] = selector; + if (selector != td->lut[j - 1]) + td->lut[j++] = selector; } v = (j == MAX_DFLL_VOLTAGES - 1) ? v_max : v_opp; selector = find_vdd_map_entry_exact(td, v); if (selector < 0) goto out; - if (selector != td->i2c_lut[j - 1]) - td->i2c_lut[j++] = selector; + if (selector != td->lut[j - 1]) + td->lut[j++] = selector; if (v >= v_max) break; } - td->i2c_lut_size = j; + td->lut_size = j; if (!td->dvco_rate_min) dev_err(td->dev, "no opp above DFLL minimum voltage %d mV\n", td->soc->cvb->min_millivolts); - else + else { ret = 0; + for (j = 0; j < td->lut_size; j++) + td->lut_uv[j] = + regulator_list_voltage(td->vdd_reg, + td->lut[j]); + } out: return ret; } +static int dfll_build_lut(struct tegra_dfll *td) +{ + unsigned long rate, v_max; + struct dev_pm_opp *opp; + + rate = ULONG_MAX; + opp = dev_pm_opp_find_freq_floor(td->soc->dev, &rate); + if (IS_ERR(opp)) { + dev_err(td->dev, "couldn't get vmax opp, empty opp table?\n"); + return -EINVAL; + } + v_max = dev_pm_opp_get_voltage(opp); + dev_pm_opp_put(opp); + + if (td->pmu_if == TEGRA_DFLL_PMU_PWM) + return dfll_build_pwm_lut(td, v_max); + else + return dfll_build_i2c_lut(td, v_max); +} + /** * read_dt_param - helper function for reading required parameters from the DT * @td: DFLL instance @@ -1526,12 +1784,57 @@ static int dfll_fetch_i2c_params(struct tegra_dfll *td) } td->i2c_reg = vsel_reg; - ret = dfll_build_i2c_lut(td); - if (ret) { - dev_err(td->dev, "couldn't build I2C LUT\n"); + return 0; +} + +static int dfll_fetch_pwm_params(struct tegra_dfll *td) +{ + int ret, i; + u32 pwm_period; + + if (!td->soc->alignment.step_uv || !td->soc->alignment.offset_uv) { + dev_err(td->dev, + "Missing step or alignment info for PWM regulator"); + return -EINVAL; + } + for (i = 0; i < MAX_DFLL_VOLTAGES; i++) + td->lut_uv[i] = td->soc->alignment.offset_uv + + i * td->soc->alignment.step_uv; + + ret = read_dt_param(td, "nvidia,pwm-tristate-microvolts", + &td->reg_init_uV); + if (!ret) { + dev_err(td->dev, "couldn't get initialized voltage\n"); return ret; } + ret = read_dt_param(td, "nvidia,pwm-period-nanoseconds", &pwm_period); + if (!ret) { + dev_err(td->dev, "couldn't get PWM period\n"); + return ret; + } + td->pwm_rate = (NSEC_PER_SEC / pwm_period) * (MAX_DFLL_VOLTAGES - 1); + + td->pwm_pin = devm_pinctrl_get(td->dev); + if (IS_ERR(td->pwm_pin)) { + dev_err(td->dev, "DT: missing pinctrl device\n"); + return PTR_ERR(td->pwm_pin); + } + + td->pwm_enable_state = pinctrl_lookup_state(td->pwm_pin, + "dvfs_pwm_enable"); + if (IS_ERR(td->pwm_enable_state)) { + dev_err(td->dev, "DT: missing pwm enabled state\n"); + return PTR_ERR(td->pwm_enable_state); + } + + td->pwm_disable_state = pinctrl_lookup_state(td->pwm_pin, + "dvfs_pwm_disable"); + if (IS_ERR(td->pwm_disable_state)) { + dev_err(td->dev, "DT: missing pwm disabled state\n"); + return PTR_ERR(td->pwm_disable_state); + } + return 0; } @@ -1597,16 +1900,6 @@ int tegra_dfll_register(struct platform_device *pdev, td->soc = soc; - td->vdd_reg = devm_regulator_get(td->dev, "vdd-cpu"); - if (IS_ERR(td->vdd_reg)) { - ret = PTR_ERR(td->vdd_reg); - if (ret != -EPROBE_DEFER) - dev_err(td->dev, "couldn't get vdd_cpu regulator: %d\n", - ret); - - return ret; - } - td->dvco_rst = devm_reset_control_get(td->dev, "dvco"); if (IS_ERR(td->dvco_rst)) { dev_err(td->dev, "couldn't get dvco reset\n"); @@ -1619,10 +1912,27 @@ int tegra_dfll_register(struct platform_device *pdev, return ret; } - ret = dfll_fetch_i2c_params(td); + if (of_property_read_bool(td->dev->of_node, "nvidia,pwm-to-pmic")) { + td->pmu_if = TEGRA_DFLL_PMU_PWM; + ret = dfll_fetch_pwm_params(td); + } else { + td->vdd_reg = devm_regulator_get(td->dev, "vdd-cpu"); + if (IS_ERR(td->vdd_reg)) { + dev_err(td->dev, "couldn't get vdd_cpu regulator\n"); + return PTR_ERR(td->vdd_reg); + } + td->pmu_if = TEGRA_DFLL_PMU_I2C; + ret = dfll_fetch_i2c_params(td); + } if (ret) return ret; + ret = dfll_build_lut(td); + if (ret) { + dev_err(td->dev, "couldn't build LUT\n"); + return ret; + } + mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (!mem) { dev_err(td->dev, "no control register resource\n");