ARM: dts: imx6: enable Murata 1MW M.2 card for imx6 legacy platforms
Enable Murata 1MW M.2 card for i.MX6 legacy platforms. Plug in Murata 1MW M.2 into SD slot by using Murata uSD-to-M.2 Adapter. Below i.MX6 legacy platforms will be supported: - i.MX6Q/QP/DL SDB, SD2 slot - i.MX6SX SDB, SD2 slot - i.MX6SLL EVK, SD3 slot - i.MX6UL/ULL/ULZ EVK, SD1 slot Signed-off-by: Fugang Duan <fugang.duan@nxp.com>5.4-rM2-2.2.x-imx-squashed
Fugang Duan
Dong Aisheng
parent
56d26191f3
commit
3ad8cc16ef
|
|
@ -439,6 +439,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
|||
imx6dl-sabreauto-flexcan1.dtb \
|
||||
imx6dl-sabrelite.dtb \
|
||||
imx6dl-sabresd.dtb \
|
||||
imx6dl-sabresd-btwifi.dtb \
|
||||
imx6dl-sabresd-hdcp.dtb \
|
||||
imx6dl-savageboard.dtb \
|
||||
imx6dl-ts4900.dtb \
|
||||
|
|
@ -521,6 +522,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
|||
imx6q-sabreauto-flexcan1.dtb \
|
||||
imx6q-sabrelite.dtb \
|
||||
imx6q-sabresd.dtb \
|
||||
imx6q-sabresd-btwifi.dtb \
|
||||
imx6q-sabresd-hdcp.dtb \
|
||||
imx6q-sabresd-uart.dtb \
|
||||
imx6q-savageboard.dtb \
|
||||
|
|
@ -550,6 +552,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
|||
imx6qp-sabreauto.dtb \
|
||||
imx6qp-sabreauto-flexcan1.dtb \
|
||||
imx6qp-sabresd.dtb \
|
||||
imx6qp-sabresd-btwifi.dtb \
|
||||
imx6qp-sabresd-hdcp.dtb \
|
||||
imx6qp-tx6qp-8037.dtb \
|
||||
imx6qp-tx6qp-8037-mb7.dtb \
|
||||
|
|
@ -561,9 +564,11 @@ dtb-$(CONFIG_SOC_IMX6SL) += \
|
|||
imx6sl-evk.dtb \
|
||||
imx6sl-evk-csi.dtb \
|
||||
imx6sl-evk-uart.dtb \
|
||||
imx6sl-evk-btwifi.dtb \
|
||||
imx6sl-warp.dtb
|
||||
dtb-$(CONFIG_SOC_IMX6SLL) += \
|
||||
imx6sll-evk.dtb
|
||||
imx6sll-evk.dtb \
|
||||
imx6sll-evk-btwifi.dtb
|
||||
dtb-$(CONFIG_SOC_IMX6SX) += \
|
||||
imx6sx-nitrogen6sx.dtb \
|
||||
imx6sx-sabreauto.dtb \
|
||||
|
|
@ -574,6 +579,7 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
|
|||
imx6sx-sdb-lcdif1.dtb \
|
||||
imx6sx-sdb-m4.dtb \
|
||||
imx6sx-sdb-mqs.dtb \
|
||||
imx6sx-sdb-btwifi.dtb \
|
||||
imx6sx-softing-vining-2000.dtb \
|
||||
imx6sx-udoo-neo-basic.dtb \
|
||||
imx6sx-udoo-neo-extended.dtb \
|
||||
|
|
@ -582,7 +588,11 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
|
|||
imx6ul-14x14-evk.dtb \
|
||||
imx6ul-14x14-evk-csi.dtb \
|
||||
imx6ul-14x14-evk-emmc.dtb \
|
||||
imx6ul-14x14-evk-btwifi.dtb \
|
||||
imx6ul-14x14-evk-btwifi-oob.dtb \
|
||||
imx6ul-9x9-evk.dtb \
|
||||
imx6ul-9x9-evk-btwifi.dtb \
|
||||
imx6ul-9x9-evk-btwifi-oob.dtb \
|
||||
imx6ul-ccimx6ulsbcexpress.dtb \
|
||||
imx6ul-ccimx6ulsbcpro.dtb \
|
||||
imx6ul-geam.dtb \
|
||||
|
|
@ -600,13 +610,18 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
|
|||
imx6ul-tx6ul-mainboard.dtb \
|
||||
imx6ull-14x14-evk.dtb \
|
||||
imx6ull-14x14-evk-emmc.dtb \
|
||||
imx6ull-14x14-evk-btwifi.dtb \
|
||||
imx6ull-14x14-evk-btwifi-oob.dtb \
|
||||
imx6ull-9x9-evk.dtb \
|
||||
imx6ull-9x9-evk-btwifi.dtb \
|
||||
imx6ull-9x9-evk-btwifi-oob.dtb \
|
||||
imx6ull-colibri-eval-v3.dtb \
|
||||
imx6ull-colibri-wifi-eval-v3.dtb \
|
||||
imx6ull-phytec-segin-ff-rdk-nand.dtb \
|
||||
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
|
||||
imx6ull-phytec-segin-lc-rdk-nand.dtb \
|
||||
imx6ulz-14x14-evk.dtb \
|
||||
imx6ulz-14x14-evk-btwifi.dtb \
|
||||
imx6ulz-14x14-evk-emmc.dtb
|
||||
dtb-$(CONFIG_SOC_IMX7D) += \
|
||||
imx7d-cl-som-imx7.dtb \
|
||||
|
|
|
|||
|
|
@ -0,0 +1,11 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6dl-sabresd.dts"
|
||||
#include "imx6qdl-sabresd-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,11 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6q-sabresd.dts"
|
||||
#include "imx6qdl-sabresd-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,104 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
/*
|
||||
* NOTE: This DTS file is wrote for plugging in Murata 1MW M.2
|
||||
* into SD2 slot by using Murata uSD-to-M.2 Adapter.
|
||||
*
|
||||
* By default, OOB IRQ is enabled with below HW rework.
|
||||
* HW rework:
|
||||
* Install R209,R210,R211,R212,R213,R214,R215 on SDB board.
|
||||
*/
|
||||
|
||||
/ {
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
modem_reset: modem-reset {
|
||||
compatible = "gpio-reset";
|
||||
reset-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <1000>;
|
||||
#reset-cells = <0>;
|
||||
};
|
||||
|
||||
usdhc1_pwrseq: usdhc1_pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&ecspi1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
imx6qdl-sabresd-murata-v2 {
|
||||
pinctrl_btreg: btreggrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0
|
||||
>;
|
||||
};
|
||||
|
||||
/* add MUXing entry for SD2 4-bit interface and configure control pins */
|
||||
pinctrl_wifi: wifigrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
|
||||
MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
|
||||
MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
|
||||
MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
|
||||
MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
|
||||
MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
|
||||
MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x13069 /* WL_REG_ON */
|
||||
MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0b001 /* WL_HOST_WAKE */
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pinctrl_gpio_leds {
|
||||
fsl,pins = <
|
||||
>;
|
||||
};
|
||||
|
||||
&uart5 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart5_1
|
||||
&pinctrl_btreg>;
|
||||
fsl,uart-has-rtscts;
|
||||
resets = <&modem_reset>;
|
||||
status = "okay";
|
||||
/* for DTE mode, add below change */
|
||||
/* fsl,dte-mode; */
|
||||
/* pinctrl-0 = <&pinctrl_uart5dte_1>; */
|
||||
};
|
||||
|
||||
&usdhc2 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_wifi>;
|
||||
bus-width = <4>;
|
||||
no-1-8-v;
|
||||
non-removable;
|
||||
keep-power-in-suspend;
|
||||
mmc-pwrseq = <&usdhc1_pwrseq>;
|
||||
pm-ignore-notify;
|
||||
cap-power-off-card;
|
||||
/delete-property/ enable-sdio-wakeup;
|
||||
|
||||
brcmf: bcrmf@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
|
||||
interrupt-names = "host-wake";
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,11 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6qp-sabresd.dts"
|
||||
#include "imx6qdl-sabresd-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,101 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
/* NOTE: This DTS file is written for plugging in Murata Wi-Fi/BT EVK into SD1
|
||||
* slot using Murata i.MX InterConnect Ver 1.0 Adapter AND wiring in control
|
||||
* signals with SD Card Extender on SD3 slot.
|
||||
* Bluetooth UART connect via SD1 EMMC/MMC Plus pinout.
|
||||
* WL_REG_ON/BT_REG_ON/WL_HOST_WAKE are connected from SD Card Extender on SD3
|
||||
* slot.
|
||||
*/
|
||||
#include "imx6sl-evk.dts"
|
||||
|
||||
/ {
|
||||
modem_reset: modem-reset {
|
||||
compatible = "gpio-reset";
|
||||
reset-gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <1000>;
|
||||
#reset-cells = <0>;
|
||||
};
|
||||
|
||||
usdhc1_pwrseq: usdhc1_pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&gpio5 16 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
imx6sl-evk-murata-v1_sdext {
|
||||
/* Only MUX SD1_DAT0..3 lines so UART4 can be MUXed on higher data lines. */
|
||||
pinctrl_btreg: btreggrp {
|
||||
fsl,pins = <
|
||||
MX6SL_PAD_SD3_DAT3__GPIO5_IO17 0x13069 /* BT_REG_ON */
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_wifi: wifigrp {
|
||||
fsl,pins = <
|
||||
MX6SL_PAD_SD1_CMD__SD1_CMD 0x17059
|
||||
MX6SL_PAD_SD1_CLK__SD1_CLK 0x10059
|
||||
MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x17059
|
||||
MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x17059
|
||||
MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x17059
|
||||
MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x17059
|
||||
MX6SL_PAD_SD3_DAT1__GPIO5_IO20 0x13069 /* WL_HOST_WAKE */
|
||||
MX6SL_PAD_SD3_DAT2__GPIO5_IO16 0x13069 /* WL_REG_ON */
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usdhc3_1: usdhc3grp-1 {
|
||||
fsl,pins = <
|
||||
MX6SL_PAD_SD3_CMD__SD3_CMD 0x17059
|
||||
MX6SL_PAD_SD3_CLK__SD3_CLK 0x10059
|
||||
MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x17059
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
/* Murata: declare UART4 interface for Bluetooth. */
|
||||
&uart4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart4_1
|
||||
&pinctrl_btreg>;
|
||||
fsl,uart-has-rtscts;
|
||||
resets = <&modem_reset>;
|
||||
status = "okay";
|
||||
/* for DTE mode, add below change */
|
||||
/* fsl,dte-mode; */
|
||||
/* pinctrl-0 = <&pinctrl_uart4dte_1>; */
|
||||
};
|
||||
|
||||
&usdhc1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_wifi>;
|
||||
bus-width = <4>;
|
||||
no-1-8-v;
|
||||
non-removable;
|
||||
mmc-pwrseq = <&usdhc1_pwrseq>;
|
||||
pm-ignore-notify;
|
||||
cap-power-off-card;
|
||||
/delete-property/ enable-sdio-wakeup;
|
||||
|
||||
brcmf: bcrmf@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
||||
&usdhc3 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usdhc3_1>;
|
||||
bus-width = <1>;
|
||||
no-1-8-v;
|
||||
};
|
||||
|
|
@ -0,0 +1,99 @@
|
|||
/*
|
||||
* Copyright (C) 2016 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
/*
|
||||
* NOTE: This DTS file is wrote for plugging in Murata 1MW M.2
|
||||
* into SD3 slot by using Murata uSD-to-M.2 Adapter.
|
||||
*
|
||||
* By default, OOB IRQ is not enabled since i.MX6SLL EVK board needs to rework.
|
||||
* How to enable OOB IRQ ?
|
||||
* HW rework:
|
||||
* Install R127 on i.MX6SLL EVK board.
|
||||
* SW change: add below pin for WL_HOST_WAKE
|
||||
* pinctrl_wifi: wifigrp {
|
||||
* fsl,pins = <
|
||||
* ...
|
||||
* MX6SLL_PAD_KEY_COL1__GPIO3_IO26 0x0b001
|
||||
* >;
|
||||
* };
|
||||
* brcmf: bcrmf@1 {
|
||||
* reg = <1>;
|
||||
* compatible = "brcm,bcm4329-fmac";
|
||||
* interrupt-parent = <&gpio3>;
|
||||
* interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
|
||||
* interrupt-names = "host-wake";
|
||||
* };
|
||||
*/
|
||||
|
||||
#include "imx6sll-evk.dts"
|
||||
|
||||
/ {
|
||||
modem_reset: modem-reset {
|
||||
compatible = "gpio-reset";
|
||||
reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <1000>;
|
||||
#reset-cells = <0>;
|
||||
};
|
||||
|
||||
usdhc1_pwrseq: usdhc1_pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
imx6sll-evk-murata-v2 {
|
||||
pinctrl_wifi: wifigrp {
|
||||
fsl,pins = <
|
||||
MX6SLL_PAD_SD3_CMD__SD3_CMD 0x170b9
|
||||
MX6SLL_PAD_SD3_CLK__SD3_CLK 0x130b9
|
||||
MX6SLL_PAD_SD3_DATA0__SD3_DATA0 0x170b9
|
||||
MX6SLL_PAD_SD3_DATA1__SD3_DATA1 0x170b9
|
||||
MX6SLL_PAD_SD3_DATA2__SD3_DATA2 0x170b9
|
||||
MX6SLL_PAD_SD3_DATA3__SD3_DATA3 0x170b9
|
||||
|
||||
MX6SLL_PAD_KEY_COL0__GPIO3_IO24 0x17059 /* WL_REG_ON */
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&lcdif {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
®_sd3_vmmc {
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
&uart5 {
|
||||
resets = <&modem_reset>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usdhc3 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_wifi>;
|
||||
bus-width = <4>;
|
||||
no-1-8-v;
|
||||
non-removable;
|
||||
mmc-pwrseq = <&usdhc1_pwrseq>;
|
||||
pm-ignore-notify;
|
||||
cap-power-off-card;
|
||||
/delete-property/ cd-gpios;
|
||||
/delete-property/ vmmc-supply;
|
||||
/delete-property/ enable-sdio-wakeup;
|
||||
|
||||
brcmf: bcrmf@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
|
@ -130,6 +130,7 @@
|
|||
regulator-min-microvolt = <3000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
gpio = <&gpio4 4 GPIO_ACTIVE_HIGH>;
|
||||
off-on-delay = <20000>;
|
||||
enable-active-high;
|
||||
};
|
||||
|
||||
|
|
|
|||
|
|
@ -0,0 +1,87 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
/*
|
||||
* NOTE: This DTS file is wrote for plugging in Murata 1MW M.2
|
||||
* into SD2 slot by using Murata uSD-to-M.2 Adapter.
|
||||
*
|
||||
* By default, OOB IRQ is not enabled since i.MX6SX SDB board needs to rework.
|
||||
* How to enable OOB IRQ ?
|
||||
* HW rework:
|
||||
* Install R328 on i.MX6SX SDB board.
|
||||
* SW change:
|
||||
* pinctrl_wifi: wifigrp {
|
||||
* fsl,pins = <
|
||||
* MX6SX_PAD_ENET1_RX_CLK__GPIO2_IO_4 0x0b001
|
||||
* >;
|
||||
* };
|
||||
* brcmf: bcrmf@1 {
|
||||
* reg = <1>;
|
||||
* compatible = "brcm,bcm4329-fmac";
|
||||
* interrupt-parent = <&gpio2>;
|
||||
* interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
||||
* interrupt-names = "host-wake";
|
||||
* };
|
||||
*/
|
||||
|
||||
#include "imx6sx-sdb.dts"
|
||||
|
||||
/ {
|
||||
modem_reset: modem-reset {
|
||||
compatible = "gpio-reset";
|
||||
reset-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <1000>;
|
||||
#reset-cells = <0>;
|
||||
};
|
||||
|
||||
usdhc2_pwrseq: usdhc2_pwrseq {
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
};
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
imx6sx-sdb-murata-wifibt {
|
||||
pinctrl_bt: btgrp {
|
||||
fsl,pins = <
|
||||
MX6SX_PAD_NAND_DATA06__GPIO4_IO_10 0x13069 /* BT_REG_ON */
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_wifi: wifigrp {
|
||||
fsl,pins = <
|
||||
>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&uart5 { /* for bluetooth */
|
||||
pinctrl-0 = <&pinctrl_uart5 &pinctrl_bt>;
|
||||
resets = <&modem_reset>;
|
||||
};
|
||||
|
||||
|
||||
&usdhc2 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_wifi>;
|
||||
bus-width = <4>;
|
||||
no-1-8-v; /* force 3.3V VIO */
|
||||
non-removable;
|
||||
mmc-pwrseq = <&usdhc2_pwrseq>;
|
||||
pm-ignore-notify;
|
||||
cap-power-off-card;
|
||||
/delete-property/ wakeup-source;
|
||||
status = "okay";
|
||||
|
||||
brcmf: bcrmf@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2017 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ul-14x14-evk-btwifi.dts"
|
||||
#include "imx6ul-evk-btwifi-oob.dtsi"
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ul-14x14-evk.dts"
|
||||
#include "imx6ul-evk-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2017 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ul-9x9-evk-btwifi.dts"
|
||||
#include "imx6ul-evk-btwifi-oob.dtsi"
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ul-9x9-evk.dts"
|
||||
#include "imx6ul-evk-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,30 @@
|
|||
/*
|
||||
* Copyright 2017-2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
&pinctrl_wifi {
|
||||
fsl,pins = <
|
||||
/* MUXing for WL_HOST_WAKE */
|
||||
MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x0b001 /* input: 100K Pull-up */
|
||||
>;
|
||||
};
|
||||
|
||||
/*
|
||||
* For WL_HOST_WAKE (OOB_IRQ) to function correctly, we must disable
|
||||
* the secondary ethernet port (FEC2). Hardware re-work is to remove
|
||||
* R1633 and populate R1704 with 0 Ohm resistor.
|
||||
* Refer to Murata Hardware Reference Manual for more details.
|
||||
*/
|
||||
&fec2 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&brcmf {
|
||||
interrupt-parent = <&gpio2>;
|
||||
interrupts = <15 IRQ_TYPE_LEVEL_LOW>; /* M.2 WL_HOST_WAKE is active low */
|
||||
interrupt-names = "host-wake";
|
||||
};
|
||||
|
|
@ -0,0 +1,72 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
* Copyright 2019 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
/*
|
||||
* NOTE: This DTS file is written for plugging in Murata Wi-Fi/BT EVK into Slot
|
||||
* SD1 and using Murata i.MX InterConnect Ver 2.0 Adapter. Bluetooth UART &
|
||||
* control signals are connected via ribbon cable (J1701 connector).
|
||||
*/
|
||||
|
||||
/ {
|
||||
modem_reset: modem-reset {
|
||||
compatible = "gpio-reset";
|
||||
reset-gpios = <&gpio_spi 4 GPIO_ACTIVE_LOW>;
|
||||
reset-delay-us = <1000>;
|
||||
#reset-cells = <0>;
|
||||
};
|
||||
|
||||
usdhc1_pwrseq: usdhc1_pwrseq {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_wifi>;
|
||||
compatible = "mmc-pwrseq-simple";
|
||||
reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
pinctrl_wifi: wifigrp {
|
||||
fsl,pins = <
|
||||
MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x03029
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
®_sd1_vmmc {
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
&uart2 {
|
||||
resets = <&modem_reset>;
|
||||
};
|
||||
|
||||
&usdhc1 {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usdhc1>;
|
||||
no-1-8-v;
|
||||
non-removable;
|
||||
pm-ignore-notify;
|
||||
mmc-pwrseq = <&usdhc1_pwrseq>;
|
||||
cap-power-off-card;
|
||||
/delete-property/ wakeup-source;
|
||||
/delete-property/ enable-sdio-wakeup;
|
||||
|
||||
brcmf: bcrmf@1 {
|
||||
reg = <1>;
|
||||
compatible = "brcm,bcm4329-fmac";
|
||||
};
|
||||
};
|
||||
|
||||
&gpio_spi {
|
||||
/* Murata: modify default setting so that BT_nPWD/BT_REG_ON
|
||||
* is low (0V) during kernel boot.
|
||||
*/
|
||||
registers-default = /bits/ 8 <0x47>;
|
||||
};
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2017 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ull-14x14-evk-btwifi.dts"
|
||||
#include "imx6ul-evk-btwifi-oob.dtsi"
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2016 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ull-14x14-evk.dts"
|
||||
#include "imx6ul-evk-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2017 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ull-9x9-evk-btwifi.dts"
|
||||
#include "imx6ul-evk-btwifi-oob.dtsi"
|
||||
|
|
@ -0,0 +1,10 @@
|
|||
/*
|
||||
* Copyright (C) 2015 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify
|
||||
* it under the terms of the GNU General Public License version 2 as
|
||||
* published by the Free Software Foundation.
|
||||
*/
|
||||
|
||||
#include "imx6ull-9x9-evk.dts"
|
||||
#include "imx6ul-evk-btwifi.dtsi"
|
||||
|
|
@ -0,0 +1,16 @@
|
|||
/*
|
||||
* Copyright 2018 NXP
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or
|
||||
* modify it under the terms of the GNU General Public License
|
||||
* as published by the Free Software Foundation; either version 2
|
||||
* of the License, or (at your option) any later version.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful,
|
||||
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
||||
* GNU General Public License for more details.
|
||||
*/
|
||||
|
||||
#include "imx6ulz-14x14-evk.dts"
|
||||
#include "imx6ul-evk-btwifi.dtsi"
|
||||
Loading…
Reference in New Issue