Merge branch 'sched/urgent' into sched/core, to pick up fixes

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Documentation/admin-guide/pm/intel_pstate.rst

@@ -324,8 +324,7 @@ Global Attributes
 
 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
 control its functionality at the system level.  They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
-CPUs.
 
 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
 argument is passed to the kernel in the command line.
@@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
 	but it affects the maximum possible value of per-policy P-state	limits
 	(see `Interpretation of Policy Attributes`_ below for details).
 
+``hwp_dynamic_boost``
+	This attribute is only present if ``intel_pstate`` works in the
+	`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+	the processor.  If set (equal to 1), it causes the minimum P-state limit
+	to be increased dynamically for a short time whenever a task previously
+	waiting on I/O is selected to run on a given logical CPU (the purpose
+	of this mechanism is to improve performance).
+
+	This setting has no effect on logical CPUs whose minimum P-state limit
+	is directly set to the highest non-turbo P-state or above it.
+
 .. _status_attr:
 
 ``status``
@@ -410,7 +420,7 @@ argument is passed to the kernel in the command line.
 	That only is supported in some configurations, though (for example, if
 	the `HWP feature is enabled in the processor <Active Mode With HWP_>`_,
 	the operation mode of the driver cannot be changed), and if it is not
-	supported in the current configuration, writes to this attribute with
+	supported in the current configuration, writes to this attribute will
 	fail with an appropriate error.
 
 Interpretation of Policy Attributes

Documentation/devicetree/bindings/input/sprd,sc27xx-vibra.txt

@@ -0,0 +1,23 @@
+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+	sc2731_pmic: pmic@0 {
+		compatible = "sprd,sc2731";
+		reg = <0>;
+		spi-max-frequency = <26000000>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vibrator@eb4 {
+			compatible = "sprd,sc2731-vibrator";
+			reg = <0xeb4>;
+		};
+	};

Documentation/driver-api/infrastructure.rst

@@ -49,10 +49,10 @@ Device Drivers Base
 Device Drivers DMA Management
 -----------------------------
 
-.. kernel-doc:: drivers/base/dma-coherent.c
+.. kernel-doc:: kernel/dma/coherent.c
    :export:
 
-.. kernel-doc:: drivers/base/dma-mapping.c
+.. kernel-doc:: kernel/dma/mapping.c
    :export:
 
 Device drivers PnP support

Documentation/filesystems/Locking

@@ -441,8 +441,6 @@ prototypes:
 	int (*iterate) (struct file *, struct dir_context *);
 	int (*iterate_shared) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -473,7 +471,7 @@ prototypes:
 };
 
 locking rules:
-	All except for ->poll_mask may block.
+	All may block.
 
 ->llseek() locking has moved from llseek to the individual llseek
 implementations.  If your fs is not using generic_file_llseek, you
@@ -505,9 +503,6 @@ in sys_read() and friends.
 the lease within the individual filesystem to record the result of the
 operation
 
-->poll_mask can be called with or without the waitqueue lock for the waitqueue
-returned from ->get_poll_head.
-
 --------------------------- dquot_operations -------------------------------
 prototypes:
 	int (*write_dquot) (struct dquot *);

Documentation/filesystems/vfs.txt

@@ -857,8 +857,6 @@ struct file_operations {
 	ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
 	int (*iterate) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -903,17 +901,6 @@ otherwise noted.
 	activity on this file and (optionally) go to sleep until there
 	is activity. Called by the select(2) and poll(2) system calls
 
-  get_poll_head: Returns the struct wait_queue_head that callers can
-  wait on.  Callers need to check the returned events using ->poll_mask
-  once woken.  Can return NULL to indicate polling is not supported,
-  or any error code using the ERR_PTR convention to indicate that a
-  grave error occured and ->poll_mask shall not be called.
-
-  poll_mask: return the mask of EPOLL* values describing the file descriptor
-  state.  Called either before going to sleep on the waitqueue returned by
-  get_poll_head, or after it has been woken.  If ->get_poll_head and
-  ->poll_mask are implemented ->poll does not need to be implement.
-
   unlocked_ioctl: called by the ioctl(2) system call.
 
   compat_ioctl: called by the ioctl(2) system call when 32 bit system calls

Documentation/kbuild/kconfig-language.txt

@@ -430,6 +430,12 @@ This sets the config program's title bar if the config program chooses
 to use it. It should be placed at the top of the configuration, before any
 other statement.
 
+'#' Kconfig source file comment:
+
+An unquoted '#' character anywhere in a source file line indicates
+the beginning of a source file comment.  The remainder of that line
+is a comment.
+
 
 Kconfig hints
 -------------

Documentation/networking/e100.rst

@@ -1,3 +1,4 @@
+==============================================================
 Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
 ==============================================================
 
@@ -86,83 +87,84 @@ Event Log Message Level:  The driver uses the message level flag to log events
 Additional Configurations
 =========================
 
-  Configuring the Driver on Different Distributions
+Configuring the Driver on Different Distributions
-  -------------------------------------------------
+-------------------------------------------------
 
-  Configuring a network driver to load properly when the system is started is
+Configuring a network driver to load properly when the system is started
-  distribution dependent. Typically, the configuration process involves adding
+is distribution dependent.  Typically, the configuration process involves
-  an alias line to /etc/modprobe.d/*.conf as well as editing other system
+adding an alias line to /etc/modprobe.d/*.conf as well as editing other
-  startup scripts and/or configuration files.  Many popular Linux
+system startup scripts and/or configuration files.  Many popular Linux
-  distributions ship with tools to make these changes for you. To learn the
+distributions ship with tools to make these changes for you.  To learn
-  proper way to configure a network device for your system, refer to your
+the proper way to configure a network device for your system, refer to
-  distribution documentation.  If during this process you are asked for the
+your distribution documentation.  If during this process you are asked
-  driver or module name, the name for the Linux Base Driver for the Intel
+for the driver or module name, the name for the Linux Base Driver for
-  PRO/100 Family of Adapters is e100.
+the Intel PRO/100 Family of Adapters is e100.
 
-  As an example, if you install the e100 driver for two PRO/100 adapters
+As an example, if you install the e100 driver for two PRO/100 adapters
-  (eth0 and eth1), add the following to a configuration file in /etc/modprobe.d/
+(eth0 and eth1), add the following to a configuration file in
+/etc/modprobe.d/::
 
        alias eth0 e100
        alias eth1 e100
 
-  Viewing Link Messages
+Viewing Link Messages
-  ---------------------
+---------------------
-  In order to see link messages and other Intel driver information on your
+
-  console, you must set the dmesg level up to six. This can be done by
+In order to see link messages and other Intel driver information on your
-  entering the following on the command line before loading the e100 driver::
+console, you must set the dmesg level up to six.  This can be done by
+entering the following on the command line before loading the e100
+driver::
 
        dmesg -n 6
 
-  If you wish to see all messages issued by the driver, including debug
+If you wish to see all messages issued by the driver, including debug
-  messages, set the dmesg level to eight.
+messages, set the dmesg level to eight.
 
-  NOTE: This setting is not saved across reboots.
+NOTE: This setting is not saved across reboots.
 
+ethtool
+-------
 
-  ethtool
+The driver utilizes the ethtool interface for driver configuration and
-  -------
+diagnostics, as well as displaying statistical information.  The ethtool
+version 1.6 or later is required for this functionality.
 
-  The driver utilizes the ethtool interface for driver configuration and
+The latest release of ethtool can be found from
-  diagnostics, as well as displaying statistical information.  The ethtool
+https://www.kernel.org/pub/software/network/ethtool/
-  version 1.6 or later is required for this functionality.
 
-  The latest release of ethtool can be found from
+Enabling Wake on LAN* (WoL)
-  https://www.kernel.org/pub/software/network/ethtool/
+---------------------------
+WoL is provided through the ethtool* utility.  For instructions on
+enabling WoL with ethtool, refer to the ethtool man page.  WoL will be
+enabled on the system during the next shut down or reboot.  For this
+driver version, in order to enable WoL, the e100 driver must be loaded
+when shutting down or rebooting the system.
 
-  Enabling Wake on LAN* (WoL)
+NAPI
-  ---------------------------
+----
-  WoL is provided through the ethtool* utility.  For instructions on enabling
-  WoL with ethtool, refer to the ethtool man page.
 
-  WoL will be enabled on the system during the next shut down or reboot. For
+NAPI (Rx polling mode) is supported in the e100 driver.
-  this driver version, in order to enable WoL, the e100 driver must be
-  loaded when shutting down or rebooting the system.
 
-  NAPI
+See https://wiki.linuxfoundation.org/networking/napi for more
-  ----
+information on NAPI.
 
-  NAPI (Rx polling mode) is supported in the e100 driver.
+Multiple Interfaces on Same Ethernet Broadcast Network
+------------------------------------------------------
 
-  See https://wiki.linuxfoundation.org/networking/napi for more information
+Due to the default ARP behavior on Linux, it is not possible to have one
-  on NAPI.
+system on two IP networks in the same Ethernet broadcast domain
+(non-partitioned switch) behave as expected.  All Ethernet interfaces
+will respond to IP traffic for any IP address assigned to the system.
+This results in unbalanced receive traffic.
 
-  Multiple Interfaces on Same Ethernet Broadcast Network
+If you have multiple interfaces in a server, either turn on ARP
-  ------------------------------------------------------
+filtering by
 
-  Due to the default ARP behavior on Linux, it is not possible to have
+(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-  one system on two IP networks in the same Ethernet broadcast domain
+    (this only works if your kernel's version is higher than 2.4.5), or
-  (non-partitioned switch) behave as expected. All Ethernet interfaces
-  will respond to IP traffic for any IP address assigned to the system.
-  This results in unbalanced receive traffic.
 
-  If you have multiple interfaces in a server, either turn on ARP
+(2) installing the interfaces in separate broadcast domains (either
-  filtering by
+    in different switches or in a switch partitioned to VLANs).
-
-  (1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-      (this only works if your kernel's version is higher than 2.4.5), or
-
-  (2) installing the interfaces in separate broadcast domains (either
-      in different switches or in a switch partitioned to VLANs).
 
 
 Support

Documentation/networking/e1000.rst

@@ -1,3 +1,4 @@
+===========================================================
 Linux* Base Driver for Intel(R) Ethernet Network Connection
 ===========================================================
 
@@ -354,57 +355,58 @@ previously mentioned to force the adapter to the same speed and duplex.
 Additional Configurations
 =========================
 
-  Jumbo Frames
+Jumbo Frames
-  ------------
+------------
-  Jumbo Frames support is enabled by changing the MTU to a value larger than
+Jumbo Frames support is enabled by changing the MTU to a value larger
-  the default of 1500.  Use the ifconfig command to increase the MTU size.
+than the default of 1500.  Use the ifconfig command to increase the MTU
-  For example::
+size.  For example::
 
        ifconfig eth<x> mtu 9000 up
 
-  This setting is not saved across reboots.  It can be made permanent if
+This setting is not saved across reboots.  It can be made permanent if
-  you add::
+you add::
 
        MTU=9000
 
-   to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
+to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
-   applies to the Red Hat distributions; other distributions may store this
+applies to the Red Hat distributions; other distributions may store this
-   setting in a different location.
+setting in a different location.
 
-  Notes:
+Notes: Degradation in throughput performance may be observed in some
-  Degradation in throughput performance may be observed in some Jumbo frames
+Jumbo frames environments.  If this is observed, increasing the
-  environments. If this is observed, increasing the application's socket buffer
+application's socket buffer size and/or increasing the
-  size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
+/proc/sys/net/ipv4/tcp_*mem entry values may help.  See the specific
-  See the specific application manual and /usr/src/linux*/Documentation/
+application manual and /usr/src/linux*/Documentation/
-  networking/ip-sysctl.txt for more details.
+networking/ip-sysctl.txt for more details.
 
-  - The maximum MTU setting for Jumbo Frames is 16110.  This value coincides
+- The maximum MTU setting for Jumbo Frames is 16110.  This value
-    with the maximum Jumbo Frames size of 16128.
+  coincides with the maximum Jumbo Frames size of 16128.
 
-  - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
+- Using Jumbo frames at 10 or 100 Mbps is not supported and may result
-    poor performance or loss of link.
+  in poor performance or loss of link.
 
-  - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
+- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
-    support Jumbo Frames. These correspond to the following product names:
+  support Jumbo Frames.  These correspond to the following product names:
-     Intel(R) PRO/1000 Gigabit Server Adapter
+  Intel(R) PRO/1000 Gigabit Server Adapter Intel(R) PRO/1000 PM Network
-     Intel(R) PRO/1000 PM Network Connection
+  Connection
 
-  ethtool
+ethtool
-  -------
+-------
-  The driver utilizes the ethtool interface for driver configuration and
+The driver utilizes the ethtool interface for driver configuration and
-  diagnostics, as well as displaying statistical information.  The ethtool
+diagnostics, as well as displaying statistical information.  The ethtool
-  version 1.6 or later is required for this functionality.
+version 1.6 or later is required for this functionality.
 
-  The latest release of ethtool can be found from
+The latest release of ethtool can be found from
-  https://www.kernel.org/pub/software/network/ethtool/
+https://www.kernel.org/pub/software/network/ethtool/
 
-  Enabling Wake on LAN* (WoL)
+Enabling Wake on LAN* (WoL)
-  ---------------------------
+---------------------------
-  WoL is configured through the ethtool* utility.
+WoL is configured through the ethtool* utility.
+
+WoL will be enabled on the system during the next shut down or reboot.
+For this driver version, in order to enable WoL, the e1000 driver must be
+loaded when shutting down or rebooting the system.
 
-  WoL will be enabled on the system during the next shut down or reboot.
-  For this driver version, in order to enable WoL, the e1000 driver must be
-  loaded when shutting down or rebooting the system.
 
 Support
 =======

Documentation/networking/strparser.txt

@@ -48,7 +48,7 @@ void strp_pause(struct strparser *strp)
      Temporarily pause a stream parser. Message parsing is suspended
      and no new messages are delivered to the upper layer.
 
-void strp_pause(struct strparser *strp)
+void strp_unpause(struct strparser *strp)
 
      Unpause a paused stream parser.
 

Documentation/trace/histogram.txt

@@ -1729,35 +1729,35 @@ If a variable isn't a key variable or prefixed with 'vals=', the
 associated event field will be saved in a variable but won't be summed
 as a value:
 
-  # echo 'hist:keys=next_pid:ts1=common_timestamp ... >> event/trigger
+  # echo 'hist:keys=next_pid:ts1=common_timestamp ...' >> event/trigger
 
 Multiple variables can be assigned at the same time.  The below would
 result in both ts0 and b being created as variables, with both
 common_timestamp and field1 additionally being summed as values:
 
-  # echo 'hist:keys=pid:vals=$ts0,$b:ts0=common_timestamp,b=field1 ... >> \
+  # echo 'hist:keys=pid:vals=$ts0,$b:ts0=common_timestamp,b=field1 ...' >> \
 	event/trigger
 
 Note that variable assignments can appear either preceding or
 following their use.  The command below behaves identically to the
 command above:
 
-  # echo 'hist:keys=pid:ts0=common_timestamp,b=field1:vals=$ts0,$b ... >> \
+  # echo 'hist:keys=pid:ts0=common_timestamp,b=field1:vals=$ts0,$b ...' >> \
 	event/trigger
 
 Any number of variables not bound to a 'vals=' prefix can also be
 assigned by simply separating them with colons.  Below is the same
 thing but without the values being summed in the histogram:
 
-  # echo 'hist:keys=pid:ts0=common_timestamp:b=field1 ... >> event/trigger
+  # echo 'hist:keys=pid:ts0=common_timestamp:b=field1 ...' >> event/trigger
 
 Variables set as above can be referenced and used in expressions on
 another event.
 
 For example, here's how a latency can be calculated:
 
-  # echo 'hist:keys=pid,prio:ts0=common_timestamp ... >> event1/trigger
+  # echo 'hist:keys=pid,prio:ts0=common_timestamp ...' >> event1/trigger
-  # echo 'hist:keys=next_pid:wakeup_lat=common_timestamp-$ts0 ... >> event2/trigger
+  # echo 'hist:keys=next_pid:wakeup_lat=common_timestamp-$ts0 ...' >> event2/trigger
 
 In the first line above, the event's timetamp is saved into the
 variable ts0.  In the next line, ts0 is subtracted from the second
@@ -1766,7 +1766,7 @@ yet another variable, 'wakeup_lat'.  The hist trigger below in turn
 makes use of the wakeup_lat variable to compute a combined latency
 using the same key and variable from yet another event:
 
-  # echo 'hist:key=pid:wakeupswitch_lat=$wakeup_lat+$switchtime_lat ... >> event3/trigger
+  # echo 'hist:key=pid:wakeupswitch_lat=$wakeup_lat+$switchtime_lat ...' >> event3/trigger
 
 2.2.2 Synthetic Events
 ----------------------
@@ -1807,10 +1807,11 @@ the command that defined it with a '!':
 At this point, there isn't yet an actual 'wakeup_latency' event
 instantiated in the event subsytem - for this to happen, a 'hist
 trigger action' needs to be instantiated and bound to actual fields
-and variables defined on other events (see Section 6.3.3 below).
+and variables defined on other events (see Section 2.2.3 below on
+how that is done using hist trigger 'onmatch' action). Once that is
+done, the 'wakeup_latency' synthetic event instance is created.
 
-Once that is done, an event instance is created, and a histogram can
+A histogram can now be defined for the new synthetic event:
-be defined using it:
 
   # echo 'hist:keys=pid,prio,lat.log2:sort=pid,lat' >> \
         /sys/kernel/debug/tracing/events/synthetic/wakeup_latency/trigger
@@ -1960,7 +1961,7 @@ hist trigger specification.
     back to that pid, the timestamp difference is calculated.  If the
     resulting latency, stored in wakeup_lat, exceeds the current
     maximum latency, the values specified in the save() fields are
-    recoreded:
+    recorded:
 
     # echo 'hist:keys=pid:ts0=common_timestamp.usecs \
             if comm=="cyclictest"' >> \

Documentation/usb/gadget_configfs.txt

@@ -226,7 +226,7 @@ $ rm configs/<config name>.<number>/<function>
 where <config name>.<number> specify the configuration and <function> is
 a symlink to a function being removed from the configuration, e.g.:
 
-$ rm configfs/c.1/ncm.usb0
+$ rm configs/c.1/ncm.usb0
 
 ...
 ...

Documentation/virtual/kvm/api.txt

@@ -4610,7 +4610,7 @@ This capability indicates that kvm will implement the interfaces to handle
 reset, migration and nested KVM for branch prediction blocking. The stfle
 facility 82 should not be provided to the guest without this capability.
 
-8.14 KVM_CAP_HYPERV_TLBFLUSH
+8.18 KVM_CAP_HYPERV_TLBFLUSH
 
 Architectures: x86
 

MAINTAINERS

@@ -2971,9 +2971,13 @@ N:	bcm585*
 N:	bcm586*
 N:	bcm88312
 N:	hr2
-F:	arch/arm64/boot/dts/broadcom/ns2*
+N:	stingray
+F:	arch/arm64/boot/dts/broadcom/northstar2/*
+F:	arch/arm64/boot/dts/broadcom/stingray/*
 F:	drivers/clk/bcm/clk-ns*
+F:	drivers/clk/bcm/clk-sr*
 F:	drivers/pinctrl/bcm/pinctrl-ns*
+F:	include/dt-bindings/clock/bcm-sr*
 
 BROADCOM KONA GPIO DRIVER
 M:	Ray Jui <rjui@broadcom.com>
@@ -4360,12 +4364,7 @@ L:	iommu@lists.linux-foundation.org
 T:	git git://git.infradead.org/users/hch/dma-mapping.git
 W:	http://git.infradead.org/users/hch/dma-mapping.git
 S:	Supported
-F:	lib/dma-debug.c
+F:	kernel/dma/
-F:	lib/dma-direct.c
-F:	lib/dma-noncoherent.c
-F:	lib/dma-virt.c
-F:	drivers/base/dma-mapping.c
-F:	drivers/base/dma-coherent.c
 F:	include/asm-generic/dma-mapping.h
 F:	include/linux/dma-direct.h
 F:	include/linux/dma-mapping.h
@@ -5674,7 +5673,7 @@ F:	drivers/crypto/caam/
 F:	Documentation/devicetree/bindings/crypto/fsl-sec4.txt
 
 FREESCALE DIU FRAMEBUFFER DRIVER
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	linux-fbdev@vger.kernel.org
 S:	Maintained
 F:	drivers/video/fbdev/fsl-diu-fb.*
@@ -5774,7 +5773,7 @@ S:	Maintained
 F:	drivers/net/wan/fsl_ucc_hdlc*
 
 FREESCALE QUICC ENGINE UCC UART DRIVER
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Maintained
 F:	drivers/tty/serial/ucc_uart.c
@@ -5798,7 +5797,7 @@ F:	drivers/net/ethernet/freescale/fs_enet/
 F:	include/linux/fs_enet_pd.h
 
 FREESCALE SOC SOUND DRIVERS
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 M:	Nicolin Chen <nicoleotsuka@gmail.com>
 M:	Xiubo Li <Xiubo.Lee@gmail.com>
 R:	Fabio Estevam <fabio.estevam@nxp.com>
@@ -9756,6 +9755,11 @@ L:	linux-scsi@vger.kernel.org
 S:	Maintained
 F:	drivers/scsi/NCR_D700.*
 
+NCSI LIBRARY:
+M:	Samuel Mendoza-Jonas <sam@mendozajonas.com>
+S:	Maintained
+F:	net/ncsi/
+
 NCT6775 HARDWARE MONITOR DRIVER
 M:	Guenter Roeck <linux@roeck-us.net>
 L:	linux-hwmon@vger.kernel.org
@@ -9882,6 +9886,7 @@ M:	Andrew Lunn <andrew@lunn.ch>
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 M:	Florian Fainelli <f.fainelli@gmail.com>
 S:	Maintained
+F:	Documentation/devicetree/bindings/net/dsa/
 F:	net/dsa/
 F:	include/net/dsa.h
 F:	include/linux/dsa/
@@ -11476,6 +11481,15 @@ W:	http://wireless.kernel.org/en/users/Drivers/p54
 S:	Obsolete
 F:	drivers/net/wireless/intersil/prism54/
 
+PROC FILESYSTEM
+R:	Alexey Dobriyan <adobriyan@gmail.com>
+L:	linux-kernel@vger.kernel.org
+L:	linux-fsdevel@vger.kernel.org
+S:	Maintained
+F:	fs/proc/
+F:	include/linux/proc_fs.h
+F:	tools/testing/selftests/proc/
+
 PROC SYSCTL
 M:	"Luis R. Rodriguez" <mcgrof@kernel.org>
 M:	Kees Cook <keescook@chromium.org>
@@ -11808,9 +11822,9 @@ F:  Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
 F:  drivers/cpufreq/qcom-cpufreq-kryo.c
 
 QUALCOMM EMAC GIGABIT ETHERNET DRIVER
-M:	Timur Tabi <timur@codeaurora.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	netdev@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/net/ethernet/qualcomm/emac/
 
 QUALCOMM HEXAGON ARCHITECTURE
@@ -13648,7 +13662,7 @@ M:	Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
 L:	iommu@lists.linux-foundation.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/konrad/swiotlb.git
 S:	Supported
-F:	lib/swiotlb.c
+F:	kernel/dma/swiotlb.c
 F:	arch/*/kernel/pci-swiotlb.c
 F:	include/linux/swiotlb.h
 
@@ -15572,9 +15586,17 @@ M:	x86@kernel.org
 L:	linux-kernel@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git x86/core
 S:	Maintained
+F:	Documentation/devicetree/bindings/x86/
 F:	Documentation/x86/
 F:	arch/x86/
 
+X86 ENTRY CODE
+M:	Andy Lutomirski <luto@kernel.org>
+L:	linux-kernel@vger.kernel.org
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git x86/asm
+S:	Maintained
+F:	arch/x86/entry/
+
 X86 MCE INFRASTRUCTURE
 M:	Tony Luck <tony.luck@intel.com>
 M:	Borislav Petkov <bp@alien8.de>
@@ -15597,7 +15619,7 @@ F:	drivers/platform/x86/
 F:	drivers/platform/olpc/
 
 X86 VDSO
-M:	Andy Lutomirski <luto@amacapital.net>
+M:	Andy Lutomirski <luto@kernel.org>
 L:	linux-kernel@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git x86/vdso
 S:	Maintained

Makefile

@@ -2,7 +2,7 @@
 VERSION = 4
 PATCHLEVEL = 18
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc3
 NAME = Merciless Moray
 
 # *DOCUMENTATION*

arch/alpha/Kconfig

@@ -555,11 +555,6 @@ config SMP
 
 	  If you don't know what to do here, say N.
 
-config HAVE_DEC_LOCK
-	bool
-	depends on SMP
-	default y
-
 config NR_CPUS
 	int "Maximum number of CPUs (2-32)"
 	range 2 32

arch/alpha/lib/Makefile

@@ -35,8 +35,6 @@ lib-y =	__divqu.o __remqu.o __divlu.o __remlu.o \
 	callback_srm.o srm_puts.o srm_printk.o \
 	fls.o
 
-lib-$(CONFIG_SMP) += dec_and_lock.o
-
 # The division routines are built from single source, with different defines.
 AFLAGS___divqu.o = -DDIV
 AFLAGS___remqu.o =       -DREM

arch/alpha/lib/dec_and_lock.c

@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * arch/alpha/lib/dec_and_lock.c
- *
- * ll/sc version of atomic_dec_and_lock()
- * 
- */
-
-#include <linux/spinlock.h>
-#include <linux/atomic.h>
-#include <linux/export.h>
-
-  asm (".text					\n\
-	.global _atomic_dec_and_lock		\n\
-	.ent _atomic_dec_and_lock		\n\
-	.align	4				\n\
-_atomic_dec_and_lock:				\n\
-	.prologue 0				\n\
-1:	ldl_l	$1, 0($16)			\n\
-	subl	$1, 1, $1			\n\
-	beq	$1, 2f				\n\
-	stl_c	$1, 0($16)			\n\
-	beq	$1, 4f				\n\
-	mb					\n\
-	clr	$0				\n\
-	ret					\n\
-2:	br	$29, 3f				\n\
-3:	ldgp	$29, 0($29)			\n\
-	br	$atomic_dec_and_lock_1..ng	\n\
-	.subsection 2				\n\
-4:	br	1b				\n\
-	.previous				\n\
-	.end _atomic_dec_and_lock");
-
-static int __used atomic_dec_and_lock_1(atomic_t *atomic, spinlock_t *lock)
-{
-	/* Slow path */
-	spin_lock(lock);
-	if (atomic_dec_and_test(atomic))
-		return 1;
-	spin_unlock(lock);
-	return 0;
-}
-EXPORT_SYMBOL(_atomic_dec_and_lock);

arch/arm/Kconfig

@@ -1245,8 +1245,14 @@ config PCI
 	  VESA. If you have PCI, say Y, otherwise N.
 
 config PCI_DOMAINS
-	bool
+	bool "Support for multiple PCI domains"
 	depends on PCI
+	help
+	  Enable PCI domains kernel management. Say Y if your machine
+	  has a PCI bus hierarchy that requires more than one PCI
+	  domain (aka segment) to be correctly managed. Say N otherwise.
+
+	  If you don't know what to do here, say N.
 
 config PCI_DOMAINS_GENERIC
 	def_bool PCI_DOMAINS

arch/arm/boot/dts/armada-385-synology-ds116.dts

@@ -139,7 +139,7 @@
 					      3700 5
 					      3900 6
 					      4000 7>;
-			cooling-cells = <2>;
+			#cooling-cells = <2>;
 		};
 
 		gpio-leds {

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -216,7 +216,7 @@
 			reg = <0x18008000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -245,7 +245,7 @@
 			reg = <0x1800b000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -256,7 +256,7 @@
 
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 
 			linux,pci-domain = <0>;
 
@@ -278,10 +278,10 @@
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
-				interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 97 IRQ_TYPE_NONE>,
+					     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 98 IRQ_TYPE_NONE>,
+					     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 99 IRQ_TYPE_NONE>;
+					     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
@@ -291,7 +291,7 @@
 
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 
 			linux,pci-domain = <1>;
 
@@ -313,10 +313,10 @@
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
-				interrupts = <GIC_SPI 102 IRQ_TYPE_NONE>,
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 103 IRQ_TYPE_NONE>,
+					     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 104 IRQ_TYPE_NONE>,
+					     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 105 IRQ_TYPE_NONE>;
+					     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 

arch/arm/boot/dts/bcm-hr2.dtsi

@@ -264,7 +264,7 @@
 			reg = <0x38000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 95 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 		};
 
@@ -279,7 +279,7 @@
 			reg = <0x3b000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 		};
 	};
@@ -300,7 +300,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -322,10 +322,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 182 IRQ_TYPE_NONE>,
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 183 IRQ_TYPE_NONE>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 184 IRQ_TYPE_NONE>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 185 IRQ_TYPE_NONE>;
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -336,7 +336,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <1>;
 
@@ -358,10 +358,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>,
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 189 IRQ_TYPE_NONE>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 190 IRQ_TYPE_NONE>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 191 IRQ_TYPE_NONE>;
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -391,7 +391,7 @@
 			reg = <0x38000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			dma-coherent;
 			status = "disabled";
@@ -496,7 +496,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -519,10 +519,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 128 IRQ_TYPE_NONE>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 129 IRQ_TYPE_NONE>,
+				     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 130 IRQ_TYPE_NONE>;
+				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -533,7 +533,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <1>;
 
@@ -556,10 +556,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 133 IRQ_TYPE_NONE>,
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 134 IRQ_TYPE_NONE>,
+				     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 135 IRQ_TYPE_NONE>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 136 IRQ_TYPE_NONE>;
+				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -570,7 +570,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <2>;
 
@@ -593,10 +593,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>,
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 140 IRQ_TYPE_NONE>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 141 IRQ_TYPE_NONE>,
+				     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 142 IRQ_TYPE_NONE>;
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -365,7 +365,7 @@
 	i2c0: i2c@18009000 {
 		compatible = "brcm,iproc-i2c";
 		reg = <0x18009000 0x50>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_NONE>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clock-frequency = <100000>;

arch/arm/boot/dts/da850.dtsi

@@ -549,11 +549,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			reg = <0x226000 0x1000>;
-			interrupts = <42 IRQ_TYPE_EDGE_BOTH
+			interrupts = <42 43 44 45 46 47 48 49 50>;
-				43 IRQ_TYPE_EDGE_BOTH 44 IRQ_TYPE_EDGE_BOTH
-				45 IRQ_TYPE_EDGE_BOTH 46 IRQ_TYPE_EDGE_BOTH
-				47 IRQ_TYPE_EDGE_BOTH 48 IRQ_TYPE_EDGE_BOTH
-				49 IRQ_TYPE_EDGE_BOTH 50 IRQ_TYPE_EDGE_BOTH>;
 			ti,ngpio = <144>;
 			ti,davinci-gpio-unbanked = <0>;
 			status = "disabled";

arch/arm/boot/dts/imx6q.dtsi

@@ -90,7 +90,7 @@
 					clocks = <&clks IMX6Q_CLK_ECSPI5>,
 						 <&clks IMX6Q_CLK_ECSPI5>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
+					dmas = <&sdma 11 8 1>, <&sdma 12 8 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};

arch/arm/boot/dts/imx6sx.dtsi

@@ -1344,7 +1344,7 @@
 			ranges = <0x81000000 0 0          0x08f80000 0 0x00010000 /* downstream I/O */
 				  0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;

arch/arm/boot/dts/socfpga.dtsi

@@ -748,13 +748,13 @@
 		nand0: nand@ff900000 {
 			#address-cells = <0x1>;
 			#size-cells = <0x1>;
-			compatible = "denali,denali-nand-dt";
+			compatible = "altr,socfpga-denali-nand";
 			reg = <0xff900000 0x100000>,
 			      <0xffb80000 0x10000>;
 			reg-names = "nand_data", "denali_reg";
 			interrupts = <0x0 0x90 0x4>;
 			dma-mask = <0xffffffff>;
-			clocks = <&nand_clk>;
+			clocks = <&nand_x_clk>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/socfpga_arria10.dtsi

@@ -593,8 +593,7 @@
 			#size-cells = <0>;
 			reg = <0xffda5000 0x100>;
 			interrupts = <0 102 4>;
-			num-chipselect = <4>;
+			num-cs = <4>;
-			bus-num = <0>;
 			/*32bit_access;*/
 			tx-dma-channel = <&pdma 16>;
 			rx-dma-channel = <&pdma 17>;
@@ -633,7 +632,7 @@
 		nand: nand@ffb90000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-			compatible = "denali,denali-nand-dt", "altr,socfpga-denali-nand";
+			compatible = "altr,socfpga-denali-nand";
 			reg = <0xffb90000 0x72000>,
 			      <0xffb80000 0x10000>;
 			reg-names = "nand_data", "denali_reg";

arch/arm/common/Makefile

@@ -10,7 +10,7 @@ obj-$(CONFIG_DMABOUNCE)		+= dmabounce.o
 obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
 obj-$(CONFIG_SHARP_SCOOP)	+= scoop.o
-obj-$(CONFIG_SMP)		+= secure_cntvoff.o
+obj-$(CONFIG_CPU_V7)		+= secure_cntvoff.o
 obj-$(CONFIG_PCI_HOST_ITE8152)  += it8152.o
 obj-$(CONFIG_MCPM)		+= mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o
 CFLAGS_REMOVE_mcpm_entry.o	= -pg

arch/arm/configs/multi_v7_defconfig

@@ -1,5 +1,4 @@
 CONFIG_SYSVIPC=y
-CONFIG_FHANDLE=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_CGROUPS=y
@@ -10,20 +9,10 @@ CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_CMDLINE_PARTITION=y
-CONFIG_ARCH_MULTI_V7=y
-# CONFIG_ARCH_MULTI_V5 is not set
-# CONFIG_ARCH_MULTI_V4 is not set
 CONFIG_ARCH_VIRT=y
 CONFIG_ARCH_ALPINE=y
 CONFIG_ARCH_ARTPEC=y
 CONFIG_MACH_ARTPEC6=y
-CONFIG_ARCH_MVEBU=y
-CONFIG_MACH_ARMADA_370=y
-CONFIG_MACH_ARMADA_375=y
-CONFIG_MACH_ARMADA_38X=y
-CONFIG_MACH_ARMADA_39X=y
-CONFIG_MACH_ARMADA_XP=y
-CONFIG_MACH_DOVE=y
 CONFIG_ARCH_AT91=y
 CONFIG_SOC_SAMA5D2=y
 CONFIG_SOC_SAMA5D3=y
@@ -32,9 +21,9 @@ CONFIG_ARCH_BCM=y
 CONFIG_ARCH_BCM_CYGNUS=y
 CONFIG_ARCH_BCM_HR2=y
 CONFIG_ARCH_BCM_NSP=y
-CONFIG_ARCH_BCM_21664=y
-CONFIG_ARCH_BCM_281XX=y
 CONFIG_ARCH_BCM_5301X=y
+CONFIG_ARCH_BCM_281XX=y
+CONFIG_ARCH_BCM_21664=y
 CONFIG_ARCH_BCM2835=y
 CONFIG_ARCH_BCM_63XX=y
 CONFIG_ARCH_BRCMSTB=y
@@ -43,14 +32,14 @@ CONFIG_MACH_BERLIN_BG2=y
 CONFIG_MACH_BERLIN_BG2CD=y
 CONFIG_MACH_BERLIN_BG2Q=y
 CONFIG_ARCH_DIGICOLOR=y
+CONFIG_ARCH_EXYNOS=y
+CONFIG_EXYNOS5420_MCPM=y
 CONFIG_ARCH_HIGHBANK=y
 CONFIG_ARCH_HISI=y
 CONFIG_ARCH_HI3xxx=y
-CONFIG_ARCH_HIX5HD2=y
 CONFIG_ARCH_HIP01=y
 CONFIG_ARCH_HIP04=y
-CONFIG_ARCH_KEYSTONE=y
+CONFIG_ARCH_HIX5HD2=y
-CONFIG_ARCH_MESON=y
 CONFIG_ARCH_MXC=y
 CONFIG_SOC_IMX50=y
 CONFIG_SOC_IMX51=y
@@ -60,29 +49,30 @@ CONFIG_SOC_IMX6SL=y
 CONFIG_SOC_IMX6SX=y
 CONFIG_SOC_IMX6UL=y
 CONFIG_SOC_IMX7D=y
-CONFIG_SOC_VF610=y
 CONFIG_SOC_LS1021A=y
+CONFIG_SOC_VF610=y
+CONFIG_ARCH_KEYSTONE=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_ARCH_MESON=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_MACH_ARMADA_370=y
+CONFIG_MACH_ARMADA_375=y
+CONFIG_MACH_ARMADA_38X=y
+CONFIG_MACH_ARMADA_39X=y
+CONFIG_MACH_ARMADA_XP=y
+CONFIG_MACH_DOVE=y
 CONFIG_ARCH_OMAP3=y
 CONFIG_ARCH_OMAP4=y
 CONFIG_SOC_OMAP5=y
 CONFIG_SOC_AM33XX=y
 CONFIG_SOC_AM43XX=y
 CONFIG_SOC_DRA7XX=y
+CONFIG_ARCH_SIRF=y
 CONFIG_ARCH_QCOM=y
-CONFIG_ARCH_MEDIATEK=y
 CONFIG_ARCH_MSM8X60=y
 CONFIG_ARCH_MSM8960=y
 CONFIG_ARCH_MSM8974=y
 CONFIG_ARCH_ROCKCHIP=y
-CONFIG_ARCH_SOCFPGA=y
-CONFIG_PLAT_SPEAR=y
-CONFIG_ARCH_SPEAR13XX=y
-CONFIG_MACH_SPEAR1310=y
-CONFIG_MACH_SPEAR1340=y
-CONFIG_ARCH_STI=y
-CONFIG_ARCH_STM32=y
-CONFIG_ARCH_EXYNOS=y
-CONFIG_EXYNOS5420_MCPM=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_EMEV2=y
 CONFIG_ARCH_R7S72100=y
@@ -99,40 +89,33 @@ CONFIG_ARCH_R8A7792=y
 CONFIG_ARCH_R8A7793=y
 CONFIG_ARCH_R8A7794=y
 CONFIG_ARCH_SH73A0=y
+CONFIG_ARCH_SOCFPGA=y
+CONFIG_PLAT_SPEAR=y
+CONFIG_ARCH_SPEAR13XX=y
+CONFIG_MACH_SPEAR1310=y
+CONFIG_MACH_SPEAR1340=y
+CONFIG_ARCH_STI=y
+CONFIG_ARCH_STM32=y
 CONFIG_ARCH_SUNXI=y
-CONFIG_ARCH_SIRF=y
 CONFIG_ARCH_TEGRA=y
-CONFIG_ARCH_TEGRA_2x_SOC=y
-CONFIG_ARCH_TEGRA_3x_SOC=y
-CONFIG_ARCH_TEGRA_114_SOC=y
-CONFIG_ARCH_TEGRA_124_SOC=y
 CONFIG_ARCH_UNIPHIER=y
 CONFIG_ARCH_U8500=y
-CONFIG_MACH_HREFV60=y
-CONFIG_MACH_SNOWBALL=y
 CONFIG_ARCH_VEXPRESS=y
 CONFIG_ARCH_VEXPRESS_TC2_PM=y
 CONFIG_ARCH_WM8850=y
 CONFIG_ARCH_ZYNQ=y
-CONFIG_TRUSTED_FOUNDATIONS=y
+CONFIG_PCIEPORTBUS=y
-CONFIG_PCI=y
-CONFIG_PCI_HOST_GENERIC=y
-CONFIG_PCI_DRA7XX=y
-CONFIG_PCI_DRA7XX_EP=y
-CONFIG_PCI_KEYSTONE=y
-CONFIG_PCI_MSI=y
 CONFIG_PCI_MVEBU=y
 CONFIG_PCI_TEGRA=y
 CONFIG_PCI_RCAR_GEN2=y
 CONFIG_PCIE_RCAR=y
-CONFIG_PCIEPORTBUS=y
+CONFIG_PCI_DRA7XX_EP=y
+CONFIG_PCI_KEYSTONE=y
 CONFIG_PCI_ENDPOINT=y
 CONFIG_PCI_ENDPOINT_CONFIGFS=y
 CONFIG_PCI_EPF_TEST=m
 CONFIG_SMP=y
 CONFIG_NR_CPUS=16
-CONFIG_HIGHPTE=y
-CONFIG_CMA=y
 CONFIG_SECCOMP=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
@@ -145,14 +128,14 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=m
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
+CONFIG_CPUFREQ_DT=y
 CONFIG_ARM_IMX6Q_CPUFREQ=y
 CONFIG_QORIQ_CPUFREQ=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
-CONFIG_NEON=y
-CONFIG_KERNEL_MODE_NEON=y
 CONFIG_ARM_ZYNQ_CPUIDLE=y
 CONFIG_ARM_EXYNOS_CPUIDLE=y
+CONFIG_KERNEL_MODE_NEON=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -170,23 +153,13 @@ CONFIG_IPV6_MIP6=m
 CONFIG_IPV6_TUNNEL=m
 CONFIG_IPV6_MULTIPLE_TABLES=y
 CONFIG_NET_DSA=m
-CONFIG_NET_SWITCHDEV=y
 CONFIG_CAN=y
-CONFIG_CAN_RAW=y
-CONFIG_CAN_BCM=y
-CONFIG_CAN_DEV=y
 CONFIG_CAN_AT91=m
 CONFIG_CAN_FLEXCAN=m
-CONFIG_CAN_RCAR=m
-CONFIG_CAN_XILINXCAN=y
-CONFIG_CAN_MCP251X=y
-CONFIG_NET_DSA_BCM_SF2=m
-CONFIG_B53=m
-CONFIG_B53_SPI_DRIVER=m
-CONFIG_B53_MDIO_DRIVER=m
-CONFIG_B53_MMAP_DRIVER=m
-CONFIG_B53_SRAB_DRIVER=m
 CONFIG_CAN_SUN4I=y
+CONFIG_CAN_XILINXCAN=y
+CONFIG_CAN_RCAR=m
+CONFIG_CAN_MCP251X=y
 CONFIG_BT=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_BCM=y
@@ -199,11 +172,9 @@ CONFIG_RFKILL_INPUT=y
 CONFIG_RFKILL_GPIO=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_DMA_CMA=y
 CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_OMAP_OCP2SCP=y
 CONFIG_SIMPLE_PM_BUS=y
-CONFIG_SUNXI_RSB=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -236,7 +207,6 @@ CONFIG_PCI_ENDPOINT_TEST=m
 CONFIG_EEPROM_AT24=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=y
-CONFIG_SCSI_MULTI_LUN=y
 CONFIG_ATA=y
 CONFIG_SATA_AHCI=y
 CONFIG_SATA_AHCI_PLATFORM=y
@@ -251,14 +221,20 @@ CONFIG_SATA_MV=y
 CONFIG_SATA_RCAR=y
 CONFIG_NETDEVICES=y
 CONFIG_VIRTIO_NET=y
-CONFIG_HIX5HD2_GMAC=y
+CONFIG_B53_SPI_DRIVER=m
+CONFIG_B53_MDIO_DRIVER=m
+CONFIG_B53_MMAP_DRIVER=m
+CONFIG_B53_SRAB_DRIVER=m
+CONFIG_NET_DSA_BCM_SF2=m
 CONFIG_SUN4I_EMAC=y
-CONFIG_MACB=y
 CONFIG_BCMGENET=m
 CONFIG_BGMAC_BCMA=y
 CONFIG_SYSTEMPORT=m
+CONFIG_MACB=y
 CONFIG_NET_CALXEDA_XGMAC=y
 CONFIG_GIANFAR=y
+CONFIG_HIX5HD2_GMAC=y
+CONFIG_E1000E=y
 CONFIG_IGB=y
 CONFIG_MV643XX_ETH=y
 CONFIG_MVNETA=y
@@ -268,19 +244,17 @@ CONFIG_R8169=y
 CONFIG_SH_ETH=y
 CONFIG_SMSC911X=y
 CONFIG_STMMAC_ETH=y
-CONFIG_STMMAC_PLATFORM=y
 CONFIG_DWMAC_DWC_QOS_ETH=y
 CONFIG_TI_CPSW=y
 CONFIG_XILINX_EMACLITE=y
 CONFIG_AT803X_PHY=y
-CONFIG_MARVELL_PHY=y
-CONFIG_SMSC_PHY=y
 CONFIG_BROADCOM_PHY=y
 CONFIG_ICPLUS_PHY=y
-CONFIG_REALTEK_PHY=y
+CONFIG_MARVELL_PHY=y
 CONFIG_MICREL_PHY=y
-CONFIG_FIXED_PHY=y
+CONFIG_REALTEK_PHY=y
 CONFIG_ROCKCHIP_PHY=y
+CONFIG_SMSC_PHY=y
 CONFIG_USB_PEGASUS=y
 CONFIG_USB_RTL8152=m
 CONFIG_USB_LAN78XX=m
@@ -288,29 +262,29 @@ CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC75XX=y
 CONFIG_USB_NET_SMSC95XX=y
 CONFIG_BRCMFMAC=m
-CONFIG_RT2X00=m
-CONFIG_RT2800USB=m
 CONFIG_MWIFIEX=m
 CONFIG_MWIFIEX_SDIO=m
+CONFIG_RT2X00=m
+CONFIG_RT2800USB=m
 CONFIG_INPUT_JOYDEV=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_QT1070=m
 CONFIG_KEYBOARD_GPIO=y
 CONFIG_KEYBOARD_TEGRA=y
-CONFIG_KEYBOARD_SPEAR=y
-CONFIG_KEYBOARD_ST_KEYSCAN=y
-CONFIG_KEYBOARD_CROS_EC=m
 CONFIG_KEYBOARD_SAMSUNG=m
+CONFIG_KEYBOARD_ST_KEYSCAN=y
+CONFIG_KEYBOARD_SPEAR=y
+CONFIG_KEYBOARD_CROS_EC=m
 CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_MOUSE_CYAPA=m
 CONFIG_MOUSE_ELAN_I2C=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=m
 CONFIG_TOUCHSCREEN_MMS114=m
+CONFIG_TOUCHSCREEN_WM97XX=m
 CONFIG_TOUCHSCREEN_ST1232=m
 CONFIG_TOUCHSCREEN_STMPE=y
 CONFIG_TOUCHSCREEN_SUN4I=y
-CONFIG_TOUCHSCREEN_WM97XX=m
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_MAX77693_HAPTIC=m
 CONFIG_INPUT_MAX8997_HAPTIC=m
@@ -327,13 +301,12 @@ CONFIG_SERIAL_8250_DW=y
 CONFIG_SERIAL_8250_EM=y
 CONFIG_SERIAL_8250_MT6577=y
 CONFIG_SERIAL_8250_UNIPHIER=y
+CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_ATMEL=y
 CONFIG_SERIAL_ATMEL_CONSOLE=y
 CONFIG_SERIAL_ATMEL_TTYAT=y
-CONFIG_SERIAL_BCM63XX=y
-CONFIG_SERIAL_BCM63XX_CONSOLE=y
 CONFIG_SERIAL_MESON=y
 CONFIG_SERIAL_MESON_CONSOLE=y
 CONFIG_SERIAL_SAMSUNG=y
@@ -345,15 +318,14 @@ CONFIG_SERIAL_IMX=y
 CONFIG_SERIAL_IMX_CONSOLE=y
 CONFIG_SERIAL_SH_SCI=y
 CONFIG_SERIAL_SH_SCI_NR_UARTS=20
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-CONFIG_SERIAL_SH_SCI_DMA=y
 CONFIG_SERIAL_MSM=y
 CONFIG_SERIAL_MSM_CONSOLE=y
 CONFIG_SERIAL_VT8500=y
 CONFIG_SERIAL_VT8500_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SERIAL_OMAP=y
 CONFIG_SERIAL_OMAP_CONSOLE=y
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
 CONFIG_SERIAL_XILINX_PS_UART=y
 CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
 CONFIG_SERIAL_FSL_LPUART=y
@@ -365,12 +337,10 @@ CONFIG_SERIAL_ST_ASC_CONSOLE=y
 CONFIG_SERIAL_STM32=y
 CONFIG_SERIAL_STM32_CONSOLE=y
 CONFIG_SERIAL_DEV_BUS=y
-CONFIG_HVC_DRIVER=y
 CONFIG_VIRTIO_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_ST=y
 CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_DAVINCI=y
-CONFIG_I2C_MESON=y
-CONFIG_I2C_MUX=y
 CONFIG_I2C_ARB_GPIO_CHALLENGE=m
 CONFIG_I2C_MUX_PCA954x=y
 CONFIG_I2C_MUX_PINCTRL=y
@@ -378,12 +348,13 @@ CONFIG_I2C_DEMUX_PINCTRL=y
 CONFIG_I2C_AT91=m
 CONFIG_I2C_BCM2835=y
 CONFIG_I2C_CADENCE=y
+CONFIG_I2C_DAVINCI=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_I2C_DIGICOLOR=m
 CONFIG_I2C_EMEV2=m
 CONFIG_I2C_GPIO=m
-CONFIG_I2C_EXYNOS5=y
 CONFIG_I2C_IMX=y
+CONFIG_I2C_MESON=y
 CONFIG_I2C_MV64XXX=y
 CONFIG_I2C_RIIC=y
 CONFIG_I2C_RK3X=y
@@ -427,7 +398,6 @@ CONFIG_SPI_SPIDEV=y
 CONFIG_SPMI=y
 CONFIG_PINCTRL_AS3722=y
 CONFIG_PINCTRL_PALMAS=y
-CONFIG_PINCTRL_BCM2835=y
 CONFIG_PINCTRL_APQ8064=y
 CONFIG_PINCTRL_APQ8084=y
 CONFIG_PINCTRL_IPQ8064=y
@@ -437,25 +407,33 @@ CONFIG_PINCTRL_MSM8X74=y
 CONFIG_PINCTRL_MSM8916=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
 CONFIG_PINCTRL_QCOM_SSBI_PMIC=y
-CONFIG_GPIO_GENERIC_PLATFORM=y
 CONFIG_GPIO_DAVINCI=y
 CONFIG_GPIO_DWAPB=y
 CONFIG_GPIO_EM=y
 CONFIG_GPIO_RCAR=y
+CONFIG_GPIO_SYSCON=y
 CONFIG_GPIO_UNIPHIER=y
 CONFIG_GPIO_XILINX=y
 CONFIG_GPIO_ZYNQ=y
 CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_PCF857X=y
-CONFIG_GPIO_TWL4030=y
 CONFIG_GPIO_PALMAS=y
-CONFIG_GPIO_SYSCON=y
 CONFIG_GPIO_TPS6586X=y
 CONFIG_GPIO_TPS65910=y
+CONFIG_GPIO_TWL4030=y
+CONFIG_POWER_AVS=y
+CONFIG_ROCKCHIP_IODOMAIN=y
+CONFIG_POWER_RESET_AS3722=y
+CONFIG_POWER_RESET_GPIO=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
+CONFIG_POWER_RESET_ST=y
+CONFIG_POWER_RESET_KEYSTONE=y
+CONFIG_POWER_RESET_RMOBILE=y
 CONFIG_BATTERY_ACT8945A=y
 CONFIG_BATTERY_CPCAP=m
 CONFIG_BATTERY_SBS=y
+CONFIG_AXP20X_POWER=m
 CONFIG_BATTERY_MAX17040=m
 CONFIG_BATTERY_MAX17042=m
 CONFIG_CHARGER_CPCAP=m
@@ -464,15 +442,6 @@ CONFIG_CHARGER_MAX77693=m
 CONFIG_CHARGER_MAX8997=m
 CONFIG_CHARGER_MAX8998=m
 CONFIG_CHARGER_TPS65090=y
-CONFIG_AXP20X_POWER=m
-CONFIG_POWER_RESET_AS3722=y
-CONFIG_POWER_RESET_GPIO=y
-CONFIG_POWER_RESET_GPIO_RESTART=y
-CONFIG_POWER_RESET_KEYSTONE=y
-CONFIG_POWER_RESET_RMOBILE=y
-CONFIG_POWER_RESET_ST=y
-CONFIG_POWER_AVS=y
-CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_SENSORS_IIO_HWMON=y
 CONFIG_SENSORS_LM90=y
 CONFIG_SENSORS_LM95245=y
@@ -480,14 +449,12 @@ CONFIG_SENSORS_NTC_THERMISTOR=m
 CONFIG_SENSORS_PWM_FAN=m
 CONFIG_SENSORS_INA2XX=m
 CONFIG_CPU_THERMAL=y
-CONFIG_BCM2835_THERMAL=m
-CONFIG_BRCMSTB_THERMAL=m
 CONFIG_IMX_THERMAL=y
 CONFIG_ROCKCHIP_THERMAL=y
 CONFIG_RCAR_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
-CONFIG_DAVINCI_WATCHDOG=m
+CONFIG_BCM2835_THERMAL=m
-CONFIG_EXYNOS_THERMAL=m
+CONFIG_BRCMSTB_THERMAL=m
 CONFIG_ST_THERMAL_MEMMAP=y
 CONFIG_WATCHDOG=y
 CONFIG_DA9063_WATCHDOG=m
@@ -495,20 +462,24 @@ CONFIG_XILINX_WATCHDOG=y
 CONFIG_ARM_SP805_WATCHDOG=y
 CONFIG_AT91SAM9X_WATCHDOG=y
 CONFIG_SAMA5D4_WATCHDOG=y
+CONFIG_DW_WATCHDOG=y
+CONFIG_DAVINCI_WATCHDOG=m
 CONFIG_ORION_WATCHDOG=y
 CONFIG_RN5T618_WATCHDOG=y
-CONFIG_ST_LPC_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=y
 CONFIG_IMX2_WDT=y
+CONFIG_ST_LPC_WATCHDOG=y
 CONFIG_TEGRA_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=y
-CONFIG_DW_WATCHDOG=y
 CONFIG_DIGICOLOR_WATCHDOG=y
 CONFIG_RENESAS_WDT=m
-CONFIG_BCM2835_WDT=y
 CONFIG_BCM47XX_WDT=y
-CONFIG_BCM7038_WDT=m
+CONFIG_BCM2835_WDT=y
 CONFIG_BCM_KONA_WDT=y
+CONFIG_BCM7038_WDT=m
+CONFIG_BCMA_HOST_SOC=y
+CONFIG_BCMA_DRIVER_GMAC_CMN=y
+CONFIG_BCMA_DRIVER_GPIO=y
 CONFIG_MFD_ACT8945A=y
 CONFIG_MFD_AS3711=y
 CONFIG_MFD_AS3722=y
@@ -516,7 +487,6 @@ CONFIG_MFD_ATMEL_FLEXCOM=y
 CONFIG_MFD_ATMEL_HLCDC=m
 CONFIG_MFD_BCM590XX=y
 CONFIG_MFD_AC100=y
-CONFIG_MFD_AXP20X=y
 CONFIG_MFD_AXP20X_I2C=y
 CONFIG_MFD_AXP20X_RSB=y
 CONFIG_MFD_CROS_EC=m
@@ -529,11 +499,11 @@ CONFIG_MFD_MAX77693=m
 CONFIG_MFD_MAX8907=y
 CONFIG_MFD_MAX8997=y
 CONFIG_MFD_MAX8998=y
-CONFIG_MFD_RK808=y
 CONFIG_MFD_CPCAP=y
 CONFIG_MFD_PM8XXX=y
 CONFIG_MFD_QCOM_RPM=y
 CONFIG_MFD_SPMI_PMIC=y
+CONFIG_MFD_RK808=y
 CONFIG_MFD_RN5T618=y
 CONFIG_MFD_SEC_CORE=y
 CONFIG_MFD_STMPE=y
@@ -543,10 +513,10 @@ CONFIG_MFD_TPS65217=y
 CONFIG_MFD_TPS65218=y
 CONFIG_MFD_TPS6586X=y
 CONFIG_MFD_TPS65910=y
-CONFIG_REGULATOR_ACT8945A=y
-CONFIG_REGULATOR_AB8500=y
 CONFIG_REGULATOR_ACT8865=y
+CONFIG_REGULATOR_ACT8945A=y
 CONFIG_REGULATOR_ANATOP=y
+CONFIG_REGULATOR_AB8500=y
 CONFIG_REGULATOR_AS3711=y
 CONFIG_REGULATOR_AS3722=y
 CONFIG_REGULATOR_AXP20X=y
@@ -554,10 +524,7 @@ CONFIG_REGULATOR_BCM590XX=y
 CONFIG_REGULATOR_CPCAP=y
 CONFIG_REGULATOR_DA9210=y
 CONFIG_REGULATOR_FAN53555=y
-CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_GPIO=y
-CONFIG_MFD_SYSCON=y
-CONFIG_POWER_RESET_SYSCON=y
 CONFIG_REGULATOR_LP872X=y
 CONFIG_REGULATOR_MAX14577=m
 CONFIG_REGULATOR_MAX8907=y
@@ -571,7 +538,8 @@ CONFIG_REGULATOR_PALMAS=y
 CONFIG_REGULATOR_PBIAS=y
 CONFIG_REGULATOR_PWM=y
 CONFIG_REGULATOR_QCOM_RPM=y
-CONFIG_REGULATOR_QCOM_SMD_RPM=y
+CONFIG_REGULATOR_QCOM_SMD_RPM=m
+CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_RN5T618=y
 CONFIG_REGULATOR_S2MPS11=y
 CONFIG_REGULATOR_S5M8767=y
@@ -592,18 +560,17 @@ CONFIG_MEDIA_CEC_SUPPORT=y
 CONFIG_MEDIA_CONTROLLER=y
 CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_MEDIA_USB_SUPPORT=y
-CONFIG_USB_VIDEO_CLASS=y
+CONFIG_USB_VIDEO_CLASS=m
-CONFIG_USB_GSPCA=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_SOC_CAMERA=m
 CONFIG_SOC_CAMERA_PLATFORM=m
-CONFIG_VIDEO_RCAR_VIN=m
-CONFIG_VIDEO_ATMEL_ISI=m
 CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS=m
 CONFIG_VIDEO_S5P_FIMC=m
 CONFIG_VIDEO_S5P_MIPI_CSIS=m
 CONFIG_VIDEO_EXYNOS_FIMC_LITE=m
 CONFIG_VIDEO_EXYNOS4_FIMC_IS=m
+CONFIG_VIDEO_RCAR_VIN=m
+CONFIG_VIDEO_ATMEL_ISI=m
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
 CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
@@ -614,19 +581,15 @@ CONFIG_VIDEO_STI_DELTA=m
 CONFIG_VIDEO_RENESAS_JPU=m
 CONFIG_VIDEO_RENESAS_VSP1=m
 CONFIG_V4L_TEST_DRIVERS=y
+CONFIG_VIDEO_VIVID=m
 CONFIG_CEC_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_SAMSUNG_S5P_CEC=m
 # CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
 CONFIG_VIDEO_ADV7180=m
 CONFIG_VIDEO_ML86V7667=m
 CONFIG_DRM=y
-CONFIG_DRM_I2C_ADV7511=m
-CONFIG_DRM_I2C_ADV7511_AUDIO=y
 # CONFIG_DRM_I2C_CH7006 is not set
 # CONFIG_DRM_I2C_SIL164 is not set
-CONFIG_DRM_DUMB_VGA_DAC=m
-CONFIG_DRM_NXP_PTN3460=m
-CONFIG_DRM_PARADE_PS8622=m
 CONFIG_DRM_NOUVEAU=m
 CONFIG_DRM_EXYNOS=m
 CONFIG_DRM_EXYNOS_FIMD=y
@@ -645,13 +608,18 @@ CONFIG_DRM_RCAR_LVDS=y
 CONFIG_DRM_SUN4I=m
 CONFIG_DRM_FSL_DCU=m
 CONFIG_DRM_TEGRA=y
+CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_PANEL_SAMSUNG_LD9040=m
 CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=m
 CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0=m
-CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_DUMB_VGA_DAC=m
+CONFIG_DRM_NXP_PTN3460=m
+CONFIG_DRM_PARADE_PS8622=m
 CONFIG_DRM_SII9234=m
+CONFIG_DRM_I2C_ADV7511=m
+CONFIG_DRM_I2C_ADV7511_AUDIO=y
 CONFIG_DRM_STI=m
-CONFIG_DRM_VC4=y
+CONFIG_DRM_VC4=m
 CONFIG_DRM_ETNAVIV=m
 CONFIG_DRM_MXSFB=m
 CONFIG_FB_ARMCLCD=y
@@ -659,8 +627,6 @@ CONFIG_FB_EFI=y
 CONFIG_FB_WM8505=y
 CONFIG_FB_SH_MOBILE_LCDC=y
 CONFIG_FB_SIMPLE=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_LCD_PLATFORM=m
 CONFIG_BACKLIGHT_PWM=y
 CONFIG_BACKLIGHT_AS3711=y
@@ -668,7 +634,6 @@ CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
 CONFIG_SOUND=m
 CONFIG_SND=m
-CONFIG_SND_DYNAMIC_MINORS=y
 CONFIG_SND_HDA_TEGRA=m
 CONFIG_SND_HDA_INPUT_BEEP=y
 CONFIG_SND_HDA_PATCH_LOADER=y
@@ -692,7 +657,7 @@ CONFIG_SND_SOC_SNOW=m
 CONFIG_SND_SOC_ODROID=m
 CONFIG_SND_SOC_SH4_FSI=m
 CONFIG_SND_SOC_RCAR=m
-CONFIG_SND_SIMPLE_SCU_CARD=m
+CONFIG_SND_SOC_STI=m
 CONFIG_SND_SUN4I_CODEC=m
 CONFIG_SND_SOC_TEGRA=m
 CONFIG_SND_SOC_TEGRA20_I2S=m
@@ -703,31 +668,25 @@ CONFIG_SND_SOC_TEGRA_WM8903=m
 CONFIG_SND_SOC_TEGRA_WM9712=m
 CONFIG_SND_SOC_TEGRA_TRIMSLICE=m
 CONFIG_SND_SOC_TEGRA_ALC5632=m
-CONFIG_SND_SOC_CPCAP=m
 CONFIG_SND_SOC_TEGRA_MAX98090=m
 CONFIG_SND_SOC_AK4642=m
+CONFIG_SND_SOC_CPCAP=m
 CONFIG_SND_SOC_SGTL5000=m
 CONFIG_SND_SOC_SPDIF=m
-CONFIG_SND_SOC_WM8978=m
-CONFIG_SND_SOC_STI=m
 CONFIG_SND_SOC_STI_SAS=m
-CONFIG_SND_SIMPLE_CARD=m
+CONFIG_SND_SOC_WM8978=m
+CONFIG_SND_SIMPLE_SCU_CARD=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_MVEBU=y
-CONFIG_USB_XHCI_RCAR=m
 CONFIG_USB_XHCI_TEGRA=m
 CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_MSM=m
-CONFIG_USB_EHCI_EXYNOS=y
-CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD_STI=y
-CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_EHCI_TEGRA=y
-CONFIG_USB_ISP1760=y
+CONFIG_USB_EHCI_EXYNOS=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_STI=y
-CONFIG_USB_OHCI_HCD_PLATFORM=y
 CONFIG_USB_OHCI_EXYNOS=m
 CONFIG_USB_R8A66597_HCD=m
 CONFIG_USB_RENESAS_USBHS=m
@@ -746,18 +705,18 @@ CONFIG_USB_TI_CPPI41_DMA=y
 CONFIG_USB_TUSB_OMAP_DMA=y
 CONFIG_USB_DWC3=y
 CONFIG_USB_DWC2=y
-CONFIG_USB_HSIC_USB3503=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_ISP1760=y
+CONFIG_USB_HSIC_USB3503=y
 CONFIG_AB8500_USB=y
-CONFIG_KEYSTONE_USB_PHY=y
+CONFIG_KEYSTONE_USB_PHY=m
 CONFIG_NOP_USB_XCEIV=m
 CONFIG_AM335X_PHY_USB=m
 CONFIG_TWL6030_USB=m
 CONFIG_USB_GPIO_VBUS=y
 CONFIG_USB_ISP1301=y
-CONFIG_USB_MSM_OTG=m
 CONFIG_USB_MXS_PHY=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_FSL_USB2=y
@@ -793,21 +752,20 @@ CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_MMC_SDHCI_DOVE=y
 CONFIG_MMC_SDHCI_TEGRA=y
+CONFIG_MMC_SDHCI_S3C=y
 CONFIG_MMC_SDHCI_PXAV3=y
 CONFIG_MMC_SDHCI_SPEAR=y
-CONFIG_MMC_SDHCI_S3C=y
 CONFIG_MMC_SDHCI_S3C_DMA=y
 CONFIG_MMC_SDHCI_BCM_KONA=y
+CONFIG_MMC_MESON_MX_SDIO=y
 CONFIG_MMC_SDHCI_ST=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MMC_ATMELMCI=y
 CONFIG_MMC_SDHCI_MSM=y
-CONFIG_MMC_MESON_MX_SDIO=y
 CONFIG_MMC_MVSDIO=y
 CONFIG_MMC_SDHI=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_PLTFM=y
 CONFIG_MMC_DW_EXYNOS=y
 CONFIG_MMC_DW_ROCKCHIP=y
 CONFIG_MMC_SH_MMCIF=y
@@ -847,94 +805,85 @@ CONFIG_RTC_DRV_MAX77686=y
 CONFIG_RTC_DRV_RK808=m
 CONFIG_RTC_DRV_RS5C372=m
 CONFIG_RTC_DRV_BQ32K=m
-CONFIG_RTC_DRV_PALMAS=y
-CONFIG_RTC_DRV_ST_LPC=y
 CONFIG_RTC_DRV_TWL4030=y
+CONFIG_RTC_DRV_PALMAS=y
 CONFIG_RTC_DRV_TPS6586X=y
 CONFIG_RTC_DRV_TPS65910=y
 CONFIG_RTC_DRV_S35390A=m
 CONFIG_RTC_DRV_RX8581=m
 CONFIG_RTC_DRV_EM3027=y
+CONFIG_RTC_DRV_S5M=m
 CONFIG_RTC_DRV_DA9063=m
 CONFIG_RTC_DRV_EFI=m
 CONFIG_RTC_DRV_DIGICOLOR=m
-CONFIG_RTC_DRV_S5M=m
 CONFIG_RTC_DRV_S3C=m
 CONFIG_RTC_DRV_PL031=y
 CONFIG_RTC_DRV_AT91RM9200=m
 CONFIG_RTC_DRV_AT91SAM9=m
 CONFIG_RTC_DRV_VT8500=y
-CONFIG_RTC_DRV_SUN6I=y
 CONFIG_RTC_DRV_SUNXI=y
 CONFIG_RTC_DRV_MV=y
 CONFIG_RTC_DRV_TEGRA=y
+CONFIG_RTC_DRV_ST_LPC=y
 CONFIG_RTC_DRV_CPCAP=m
 CONFIG_DMADEVICES=y
-CONFIG_DW_DMAC=y
 CONFIG_AT_HDMAC=y
 CONFIG_AT_XDMAC=y
+CONFIG_DMA_BCM2835=y
+CONFIG_DMA_SUN6I=y
 CONFIG_FSL_EDMA=y
+CONFIG_IMX_DMA=y
+CONFIG_IMX_SDMA=y
 CONFIG_MV_XOR=y
+CONFIG_MXS_DMA=y
+CONFIG_PL330_DMA=y
+CONFIG_SIRF_DMA=y
+CONFIG_STE_DMA40=y
+CONFIG_ST_FDMA=m
 CONFIG_TEGRA20_APB_DMA=y
+CONFIG_XILINX_DMA=y
+CONFIG_QCOM_BAM_DMA=y
+CONFIG_DW_DMAC=y
 CONFIG_SH_DMAE=y
 CONFIG_RCAR_DMAC=y
 CONFIG_RENESAS_USB_DMAC=m
-CONFIG_STE_DMA40=y
+CONFIG_VIRTIO_PCI=y
-CONFIG_SIRF_DMA=y
+CONFIG_VIRTIO_MMIO=y
-CONFIG_TI_EDMA=y
-CONFIG_PL330_DMA=y
-CONFIG_IMX_SDMA=y
-CONFIG_IMX_DMA=y
-CONFIG_MXS_DMA=y
-CONFIG_DMA_BCM2835=y
-CONFIG_DMA_OMAP=y
-CONFIG_QCOM_BAM_DMA=y
-CONFIG_XILINX_DMA=y
-CONFIG_DMA_SUN6I=y
-CONFIG_ST_FDMA=m
 CONFIG_STAGING=y
-CONFIG_SENSORS_ISL29018=y
-CONFIG_SENSORS_ISL29028=y
 CONFIG_MFD_NVEC=y
 CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y
 CONFIG_NVEC_POWER=y
 CONFIG_NVEC_PAZ00=y
-CONFIG_BCMA=y
-CONFIG_BCMA_HOST_SOC=y
-CONFIG_BCMA_DRIVER_GMAC_CMN=y
-CONFIG_BCMA_DRIVER_GPIO=y
-CONFIG_QCOM_GSBI=y
-CONFIG_QCOM_PM=y
-CONFIG_QCOM_SMEM=y
-CONFIG_QCOM_SMD_RPM=y
-CONFIG_QCOM_SMP2P=y
-CONFIG_QCOM_SMSM=y
-CONFIG_QCOM_WCNSS_CTRL=m
-CONFIG_ROCKCHIP_PM_DOMAINS=y
-CONFIG_COMMON_CLK_QCOM=y
-CONFIG_QCOM_CLK_RPM=y
-CONFIG_CHROME_PLATFORMS=y
 CONFIG_STAGING_BOARD=y
-CONFIG_CROS_EC_CHARDEV=m
 CONFIG_COMMON_CLK_MAX77686=y
 CONFIG_COMMON_CLK_RK808=m
 CONFIG_COMMON_CLK_S2MPS11=m
+CONFIG_COMMON_CLK_QCOM=y
+CONFIG_QCOM_CLK_RPM=y
 CONFIG_APQ_MMCC_8084=y
 CONFIG_MSM_GCC_8660=y
 CONFIG_MSM_MMCC_8960=y
 CONFIG_MSM_MMCC_8974=y
-CONFIG_HWSPINLOCK_QCOM=y
+CONFIG_BCM2835_MBOX=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_REMOTEPROC=m
 CONFIG_ST_REMOTEPROC=m
 CONFIG_RPMSG_VIRTIO=m
+CONFIG_RASPBERRYPI_POWER=y
+CONFIG_QCOM_GSBI=y
+CONFIG_QCOM_PM=y
+CONFIG_QCOM_SMD_RPM=m
+CONFIG_QCOM_WCNSS_CTRL=m
+CONFIG_ROCKCHIP_PM_DOMAINS=y
+CONFIG_ARCH_TEGRA_2x_SOC=y
+CONFIG_ARCH_TEGRA_3x_SOC=y
+CONFIG_ARCH_TEGRA_114_SOC=y
+CONFIG_ARCH_TEGRA_124_SOC=y
 CONFIG_PM_DEVFREQ=y
 CONFIG_ARM_TEGRA_DEVFREQ=m
-CONFIG_MEMORY=y
-CONFIG_EXTCON=y
 CONFIG_TI_AEMIF=y
 CONFIG_IIO=y
 CONFIG_IIO_SW_TRIGGER=y
@@ -947,56 +896,54 @@ CONFIG_VF610_ADC=m
 CONFIG_XILINX_XADC=y
 CONFIG_MPU3050_I2C=y
 CONFIG_CM36651=m
+CONFIG_SENSORS_ISL29018=y
+CONFIG_SENSORS_ISL29028=y
 CONFIG_AK8975=y
-CONFIG_RASPBERRYPI_POWER=y
 CONFIG_IIO_HRTIMER_TRIGGER=y
 CONFIG_PWM=y
 CONFIG_PWM_ATMEL=m
 CONFIG_PWM_ATMEL_HLCDC_PWM=m
 CONFIG_PWM_ATMEL_TCB=m
+CONFIG_PWM_BCM2835=y
+CONFIG_PWM_BRCMSTB=m
 CONFIG_PWM_FSL_FTM=m
 CONFIG_PWM_MESON=m
 CONFIG_PWM_RCAR=m
 CONFIG_PWM_RENESAS_TPU=y
 CONFIG_PWM_ROCKCHIP=m
 CONFIG_PWM_SAMSUNG=m
+CONFIG_PWM_STI=y
 CONFIG_PWM_SUN4I=y
 CONFIG_PWM_TEGRA=y
 CONFIG_PWM_VT8500=y
+CONFIG_KEYSTONE_IRQ=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_SUN9I_USB=y
 CONFIG_PHY_HIX5HD2_SATA=y
-CONFIG_E1000E=y
+CONFIG_PHY_BERLIN_SATA=y
-CONFIG_PWM_STI=y
+CONFIG_PHY_BERLIN_USB=y
-CONFIG_PWM_BCM2835=y
+CONFIG_PHY_CPCAP_USB=m
-CONFIG_PWM_BRCMSTB=m
+CONFIG_PHY_QCOM_APQ8064_SATA=m
+CONFIG_PHY_RCAR_GEN2=m
+CONFIG_PHY_ROCKCHIP_DP=m
+CONFIG_PHY_ROCKCHIP_USB=y
+CONFIG_PHY_SAMSUNG_USB2=m
+CONFIG_PHY_MIPHY28LP=y
+CONFIG_PHY_STIH407_USB=y
+CONFIG_PHY_STM32_USBPHYC=y
+CONFIG_PHY_TEGRA_XUSB=y
 CONFIG_PHY_DM816X_USB=m
 CONFIG_OMAP_USB2=y
 CONFIG_TI_PIPE3=y
 CONFIG_TWL4030_USB=m
-CONFIG_PHY_BERLIN_USB=y
-CONFIG_PHY_CPCAP_USB=m
-CONFIG_PHY_BERLIN_SATA=y
-CONFIG_PHY_ROCKCHIP_DP=m
-CONFIG_PHY_ROCKCHIP_USB=y
-CONFIG_PHY_QCOM_APQ8064_SATA=m
-CONFIG_PHY_MIPHY28LP=y
-CONFIG_PHY_RCAR_GEN2=m
-CONFIG_PHY_STIH407_USB=y
-CONFIG_PHY_STM32_USBPHYC=y
-CONFIG_PHY_SUN4I_USB=y
-CONFIG_PHY_SUN9I_USB=y
-CONFIG_PHY_SAMSUNG_USB2=m
-CONFIG_PHY_TEGRA_XUSB=y
-CONFIG_PHY_BRCM_SATA=y
-CONFIG_NVMEM=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_SUNXI_SID=y
 CONFIG_NVMEM_VF610_OCOTP=y
-CONFIG_BCM2835_MBOX=y
 CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_EFI_VARS=m
-CONFIG_EFI_CAPSULE_LOADER=m
 CONFIG_BCM47XX_NVRAM=y
 CONFIG_BCM47XX_SPROM=y
+CONFIG_EFI_VARS=m
+CONFIG_EFI_CAPSULE_LOADER=m
 CONFIG_EXT4_FS=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_MSDOS_FS=y
@@ -1004,7 +951,6 @@ CONFIG_VFAT_FS=y
 CONFIG_NTFS_FS=y
 CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_UBIFS_FS=y
-CONFIG_TMPFS=y
 CONFIG_SQUASHFS=y
 CONFIG_SQUASHFS_LZO=y
 CONFIG_SQUASHFS_XZ=y
@@ -1020,13 +966,7 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_LOCKUP_DETECTOR=y
-CONFIG_CPUFREQ_DT=y
-CONFIG_KEYSTONE_IRQ=y
-CONFIG_HW_RANDOM=y
-CONFIG_HW_RANDOM_ST=y
 CONFIG_CRYPTO_USER=m
 CONFIG_CRYPTO_USER_API_HASH=m
 CONFIG_CRYPTO_USER_API_SKCIPHER=m
@@ -1035,27 +975,19 @@ CONFIG_CRYPTO_USER_API_AEAD=m
 CONFIG_CRYPTO_DEV_MARVELL_CESA=m
 CONFIG_CRYPTO_DEV_EXYNOS_RNG=m
 CONFIG_CRYPTO_DEV_S5P=m
+CONFIG_CRYPTO_DEV_ATMEL_AES=m
+CONFIG_CRYPTO_DEV_ATMEL_TDES=m
+CONFIG_CRYPTO_DEV_ATMEL_SHA=m
 CONFIG_CRYPTO_DEV_SUN4I_SS=m
 CONFIG_CRYPTO_DEV_ROCKCHIP=m
 CONFIG_ARM_CRYPTO=y
-CONFIG_CRYPTO_SHA1_ARM=m
 CONFIG_CRYPTO_SHA1_ARM_NEON=m
 CONFIG_CRYPTO_SHA1_ARM_CE=m
 CONFIG_CRYPTO_SHA2_ARM_CE=m
-CONFIG_CRYPTO_SHA256_ARM=m
 CONFIG_CRYPTO_SHA512_ARM=m
 CONFIG_CRYPTO_AES_ARM=m
 CONFIG_CRYPTO_AES_ARM_BS=m
 CONFIG_CRYPTO_AES_ARM_CE=m
-CONFIG_CRYPTO_CHACHA20_NEON=m
-CONFIG_CRYPTO_CRC32_ARM_CE=m
-CONFIG_CRYPTO_CRCT10DIF_ARM_CE=m
 CONFIG_CRYPTO_GHASH_ARM_CE=m
-CONFIG_CRYPTO_DEV_ATMEL_AES=m
+CONFIG_CRYPTO_CRC32_ARM_CE=m
-CONFIG_CRYPTO_DEV_ATMEL_TDES=m
+CONFIG_CRYPTO_CHACHA20_NEON=m
-CONFIG_CRYPTO_DEV_ATMEL_SHA=m
-CONFIG_VIDEO_VIVID=m
-CONFIG_VIRTIO=y
-CONFIG_VIRTIO_PCI=y
-CONFIG_VIRTIO_PCI_LEGACY=y
-CONFIG_VIRTIO_MMIO=y

arch/arm/kernel/signal.c

@@ -544,7 +544,7 @@ static void handle_signal(struct ksignal *ksig, struct pt_regs *regs)
 	 * Increment event counter and perform fixup for the pre-signal
 	 * frame.
 	 */
-	rseq_signal_deliver(regs);
+	rseq_signal_deliver(ksig, regs);
 
 	/*
 	 * Set up the stack frame
@@ -666,7 +666,7 @@ do_work_pending(struct pt_regs *regs, unsigned int thread_flags, int syscall)
 			} else {
 				clear_thread_flag(TIF_NOTIFY_RESUME);
 				tracehook_notify_resume(regs);
-				rseq_handle_notify_resume(regs);
+				rseq_handle_notify_resume(NULL, regs);
 			}
 		}
 		local_irq_disable();

arch/arm/mach-bcm/Kconfig

@@ -20,6 +20,7 @@ config ARCH_BCM_IPROC
 	select GPIOLIB
 	select ARM_AMBA
 	select PINCTRL
+	select PCI_DOMAINS if PCI
 	help
 	  This enables support for systems based on Broadcom IPROC architected SoCs.
 	  The IPROC complex contains one or more ARM CPUs along with common

arch/arm/mach-davinci/board-da850-evm.c

@@ -774,7 +774,7 @@ static struct gpiod_lookup_table mmc_gpios_table = {
 		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd",
 			    GPIO_ACTIVE_LOW),
 		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp",
-			    GPIO_ACTIVE_LOW),
+			    GPIO_ACTIVE_HIGH),
 	},
 };
 

arch/arm/mach-socfpga/Kconfig

@@ -10,6 +10,7 @@ menuconfig ARCH_SOCFPGA
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
 	select MFD_SYSCON
+	select PCI_DOMAINS if PCI
 
 if ARCH_SOCFPGA
 config SOCFPGA_SUSPEND

arch/arm/xen/enlighten.c

@@ -59,6 +59,9 @@ struct xen_memory_region xen_extra_mem[XEN_EXTRA_MEM_MAX_REGIONS] __initdata;
 
 static __read_mostly unsigned int xen_events_irq;
 
+uint32_t xen_start_flags;
+EXPORT_SYMBOL(xen_start_flags);
+
 int xen_remap_domain_gfn_array(struct vm_area_struct *vma,
 			       unsigned long addr,
 			       xen_pfn_t *gfn, int nr,
@@ -293,9 +296,7 @@ void __init xen_early_init(void)
 	xen_setup_features();
 
 	if (xen_feature(XENFEAT_dom0))
-		xen_start_info->flags |= SIF_INITDOMAIN|SIF_PRIVILEGED;
+		xen_start_flags |= SIF_INITDOMAIN|SIF_PRIVILEGED;
-	else
-		xen_start_info->flags &= ~(SIF_INITDOMAIN|SIF_PRIVILEGED);
 
 	if (!console_set_on_cmdline && !xen_initial_domain())
 		add_preferred_console("hvc", 0, NULL);

arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi

@@ -309,8 +309,7 @@
 			interrupts = <0 99 4>;
 			resets = <&rst SPIM0_RESET>;
 			reg-io-width = <4>;
-			num-chipselect = <4>;
+			num-cs = <4>;
-			bus-num = <0>;
 			status = "disabled";
 		};
 
@@ -322,8 +321,7 @@
 			interrupts = <0 100 4>;
 			resets = <&rst SPIM1_RESET>;
 			reg-io-width = <4>;
-			num-chipselect = <4>;
+			num-cs = <4>;
-			bus-num = <0>;
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/amlogic/meson-axg-s400.dts

@@ -66,9 +66,22 @@
 
 &ethmac {
 	status = "okay";
-	phy-mode = "rgmii";
 	pinctrl-0 = <&eth_rgmii_y_pins>;
 	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
+			reg = <0>;
+			eee-broken-1000t;
+		};
+	};
 };
 
 &uart_A {

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

@@ -132,7 +132,7 @@
 
 			sd_emmc_b: sd@5000 {
 				compatible = "amlogic,meson-axg-mmc";
-				reg = <0x0 0x5000 0x0 0x2000>;
+				reg = <0x0 0x5000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_B>,
@@ -144,7 +144,7 @@
 
 			sd_emmc_c: mmc@7000 {
 				compatible = "amlogic,meson-axg-mmc";
-				reg = <0x0 0x7000 0x0 0x2000>;
+				reg = <0x0 0x7000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_C>,

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -35,6 +35,12 @@
 			no-map;
 		};
 
+		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved_alt: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x300000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -457,21 +463,21 @@
 
 			sd_emmc_a: mmc@70000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x70000 0x0 0x2000>;
+				reg = <0x0 0x70000 0x0 0x800>;
 				interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_b: mmc@72000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x72000 0x0 0x2000>;
+				reg = <0x0 0x72000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_c: mmc@74000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x74000 0x0 0x2000>;
+				reg = <0x0 0x74000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};

arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi

@@ -6,7 +6,7 @@
 
 &apb {
 	mali: gpu@c0000 {
-		compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
+		compatible = "amlogic,meson-gxl-mali", "arm,mali-450";
 		reg = <0x0 0xc0000 0x0 0x40000>;
 		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts

@@ -234,9 +234,6 @@
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
 	max-frequency = <100000000>;
 	disable-wp;
 

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi

@@ -189,3 +189,10 @@
 &usb0 {
 	status = "okay";
 };
+
+&usb2_phy0 {
+	/*
+	 * HDMI_5V is also used as supply for the USB VBUS.
+	 */
+	phy-supply = <&hdmi_5v>;
+};

arch/arm64/boot/dts/amlogic/meson-gxl.dtsi

@@ -13,14 +13,6 @@
 / {
 	compatible = "amlogic,meson-gxl";
 
-	reserved-memory {
-		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
-		secmon_reserved_alt: secmon@5000000 {
-			reg = <0x0 0x05000000 0x0 0x300000>;
-			no-map;
-		};
-	};
-
 	soc {
 		usb0: usb@c9000000 {
 			status = "disabled";

arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi

@@ -118,7 +118,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -149,7 +149,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <4>;
 
@@ -566,7 +566,7 @@
 			reg = <0x66080000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 394 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -594,7 +594,7 @@
 			reg = <0x660b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 395 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts

@@ -43,6 +43,10 @@
 	enet-phy-lane-swap;
 };
 
+&sdio0 {
+	mmc-ddr-1_8v;
+};
+
 &uart2 {
 	status = "okay";
 };

arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts

@@ -42,3 +42,7 @@
 &gphy0 {
 	enet-phy-lane-swap;
 };
+
+&sdio0 {
+	mmc-ddr-1_8v;
+};

arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi

@@ -409,7 +409,7 @@
 			reg = <0x000b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 177 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -453,7 +453,7 @@
 			reg = <0x000e0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 178 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts

@@ -585,6 +585,8 @@
 	vmmc-supply = <&wlan_en>;
 	ti,non-removable;
 	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
 	#address-cells = <0x1>;
 	#size-cells = <0x0>;
 	status = "ok";

arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts

@@ -322,6 +322,8 @@
 		dwmmc_2: dwmmc2@f723f000 {
 			bus-width = <0x4>;
 			non-removable;
+			cap-power-off-card;
+			keep-power-in-suspend;
 			vmmc-supply = <&reg_vdd_3v3>;
 			mmc-pwrseq = <&wl1835_pwrseq>;
 

arch/arm64/boot/dts/marvell/armada-cp110.dtsi

@@ -149,7 +149,7 @@
 
 		CP110_LABEL(icu): interrupt-controller@1e0000 {
 			compatible = "marvell,cp110-icu";
-			reg = <0x1e0000 0x10>;
+			reg = <0x1e0000 0x440>;
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			msi-parent = <&gicp>;

arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi

@@ -75,7 +75,7 @@
 
 		serial@75b1000 {
 			label = "LS-UART0";
-			status = "okay";
+			status = "disabled";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_uart2_4pins_default>;
 			pinctrl-1 = <&blsp2_uart2_4pins_sleep>;

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -1191,14 +1191,14 @@
 
 				port@0 {
 					reg = <0>;
-					etf_out: endpoint {
+					etf_in: endpoint {
 						slave-mode;
 						remote-endpoint = <&funnel0_out>;
 					};
 				};
 				port@1 {
 					reg = <0>;
-					etf_in: endpoint {
+					etf_out: endpoint {
 						remote-endpoint = <&replicator_in>;
 					};
 				};

arch/arm64/boot/dts/socionext/uniphier-ld11-global.dts

@@ -54,7 +54,7 @@
 	sound {
 		compatible = "audio-graph-card";
 		label = "UniPhier LD11";
-		widgets = "Headphone", "Headphone Jack";
+		widgets = "Headphone", "Headphones";
 		dais = <&i2s_port2
 			&i2s_port3
 			&i2s_port4

arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts

@@ -54,7 +54,7 @@
 	sound {
 		compatible = "audio-graph-card";
 		label = "UniPhier LD20";
-		widgets = "Headphone", "Headphone Jack";
+		widgets = "Headphone", "Headphones";
 		dais = <&i2s_port2
 			&i2s_port3
 			&i2s_port4

arch/arm64/configs/defconfig

@@ -47,6 +47,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_ARCH_QCOM=y
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_ARCH_SEATTLE=y
+CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_R8A7795=y
 CONFIG_ARCH_R8A7796=y
@@ -58,7 +59,6 @@ CONFIG_ARCH_R8A77995=y
 CONFIG_ARCH_STRATIX10=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_ARCH_SPRD=y
-CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_THUNDER=y
 CONFIG_ARCH_THUNDER2=y
 CONFIG_ARCH_UNIPHIER=y
@@ -67,25 +67,23 @@ CONFIG_ARCH_XGENE=y
 CONFIG_ARCH_ZX=y
 CONFIG_ARCH_ZYNQMP=y
 CONFIG_PCI=y
-CONFIG_HOTPLUG_PCI_PCIE=y
 CONFIG_PCI_IOV=y
 CONFIG_HOTPLUG_PCI=y
 CONFIG_HOTPLUG_PCI_ACPI=y
-CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCI_HISI=y
-CONFIG_PCIE_QCOM=y
-CONFIG_PCIE_KIRIN=y
-CONFIG_PCIE_ARMADA_8K=y
-CONFIG_PCIE_HISI_STB=y
 CONFIG_PCI_AARDVARK=y
 CONFIG_PCI_TEGRA=y
 CONFIG_PCIE_RCAR=y
-CONFIG_PCIE_ROCKCHIP=y
-CONFIG_PCIE_ROCKCHIP_HOST=m
 CONFIG_PCI_HOST_GENERIC=y
 CONFIG_PCI_XGENE=y
 CONFIG_PCI_HOST_THUNDER_PEM=y
 CONFIG_PCI_HOST_THUNDER_ECAM=y
+CONFIG_PCIE_ROCKCHIP_HOST=m
+CONFIG_PCI_LAYERSCAPE=y
+CONFIG_PCI_HISI=y
+CONFIG_PCIE_QCOM=y
+CONFIG_PCIE_ARMADA_8K=y
+CONFIG_PCIE_KIRIN=y
+CONFIG_PCIE_HISI_STB=y
 CONFIG_ARM64_VA_BITS_48=y
 CONFIG_SCHED_MC=y
 CONFIG_NUMA=y
@@ -104,8 +102,6 @@ CONFIG_HIBERNATION=y
 CONFIG_WQ_POWER_EFFICIENT_DEFAULT=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_GOV_ATTR_SET=y
-CONFIG_CPU_FREQ_GOV_COMMON=y
 CONFIG_CPU_FREQ_STAT=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
@@ -113,11 +109,11 @@ CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
+CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_ARM_ARMADA_37XX_CPUFREQ=y
 CONFIG_ARM_BIG_LITTLE_CPUFREQ=y
 CONFIG_ARM_SCPI_CPUFREQ=y
 CONFIG_ARM_TEGRA186_CPUFREQ=y
-CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -236,11 +232,6 @@ CONFIG_SMSC911X=y
 CONFIG_SNI_AVE=y
 CONFIG_SNI_NETSEC=y
 CONFIG_STMMAC_ETH=m
-CONFIG_DWMAC_IPQ806X=m
-CONFIG_DWMAC_MESON=m
-CONFIG_DWMAC_ROCKCHIP=m
-CONFIG_DWMAC_SUNXI=m
-CONFIG_DWMAC_SUN8I=m
 CONFIG_MDIO_BUS_MUX_MMIOREG=y
 CONFIG_AT803X_PHY=m
 CONFIG_MARVELL_PHY=m
@@ -269,8 +260,8 @@ CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_ADC=m
-CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=m
 CONFIG_INPUT_MISC=y
@@ -296,17 +287,13 @@ CONFIG_SERIAL_SAMSUNG=y
 CONFIG_SERIAL_SAMSUNG_CONSOLE=y
 CONFIG_SERIAL_TEGRA=y
 CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=11
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
 CONFIG_SERIAL_MSM=y
 CONFIG_SERIAL_MSM_CONSOLE=y
 CONFIG_SERIAL_XILINX_PS_UART=y
 CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
 CONFIG_SERIAL_MVEBU_UART=y
 CONFIG_SERIAL_DEV_BUS=y
-CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
 CONFIG_VIRTIO_CONSOLE=y
-CONFIG_I2C_HID=m
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_PCA954x=y
@@ -325,26 +312,26 @@ CONFIG_I2C_RCAR=y
 CONFIG_I2C_CROS_EC_TUNNEL=y
 CONFIG_SPI=y
 CONFIG_SPI_ARMADA_3700=y
-CONFIG_SPI_MESON_SPICC=m
-CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_BCM2835=m
 CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_MESON_SPICC=m
+CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
-CONFIG_SPI_QUP=y
 CONFIG_SPI_ROCKCHIP=y
+CONFIG_SPI_QUP=y
 CONFIG_SPI_S3C64XX=y
 CONFIG_SPI_SPIDEV=m
 CONFIG_SPMI=y
-CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_PINCTRL_MAX77620=y
+CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_MSM8916=y
 CONFIG_PINCTRL_MSM8994=y
 CONFIG_PINCTRL_MSM8996=y
-CONFIG_PINCTRL_MT7622=y
 CONFIG_PINCTRL_QDF2XXX=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
+CONFIG_PINCTRL_MT7622=y
 CONFIG_GPIO_DWAPB=y
 CONFIG_GPIO_MB86S7X=y
 CONFIG_GPIO_PL061=y
@@ -368,13 +355,13 @@ CONFIG_SENSORS_INA2XX=m
 CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
+CONFIG_ROCKCHIP_THERMAL=m
+CONFIG_RCAR_GEN3_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-CONFIG_RCAR_GEN3_THERMAL=y
-CONFIG_QCOM_TSENS=y
-CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_TEGRA_BPMP_THERMAL=m
+CONFIG_QCOM_TSENS=y
 CONFIG_UNIPHIER_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
@@ -395,9 +382,9 @@ CONFIG_MFD_MAX77620=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
 CONFIG_MFD_SEC_CORE=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_AXP20X=y
 CONFIG_REGULATOR_FAN53555=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_HI6421V530=y
 CONFIG_REGULATOR_HI655X=y
@@ -407,16 +394,15 @@ CONFIG_REGULATOR_QCOM_SMD_RPM=y
 CONFIG_REGULATOR_QCOM_SPMI=y
 CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_S2MPS11=y
+CONFIG_RC_CORE=m
+CONFIG_RC_DECODERS=y
+CONFIG_RC_DEVICES=y
+CONFIG_IR_MESON=m
 CONFIG_MEDIA_SUPPORT=m
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
 CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
 CONFIG_MEDIA_CONTROLLER=y
-CONFIG_MEDIA_RC_SUPPORT=y
-CONFIG_RC_CORE=m
-CONFIG_RC_DEVICES=y
-CONFIG_RC_DECODERS=y
-CONFIG_IR_MESON=m
 CONFIG_VIDEO_V4L2_SUBDEV_API=y
 # CONFIG_DVB_NET is not set
 CONFIG_V4L_MEM2MEM_DRIVERS=y
@@ -441,8 +427,7 @@ CONFIG_ROCKCHIP_DW_HDMI=y
 CONFIG_ROCKCHIP_DW_MIPI_DSI=y
 CONFIG_ROCKCHIP_INNO_HDMI=y
 CONFIG_DRM_RCAR_DU=m
-CONFIG_DRM_RCAR_LVDS=y
+CONFIG_DRM_RCAR_LVDS=m
-CONFIG_DRM_RCAR_VSP=y
 CONFIG_DRM_TEGRA=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_I2C_ADV7511=m
@@ -455,7 +440,6 @@ CONFIG_FB_ARMCLCD=y
 CONFIG_BACKLIGHT_GENERIC=m
 CONFIG_BACKLIGHT_PWM=m
 CONFIG_BACKLIGHT_LP855X=m
-CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
@@ -468,6 +452,7 @@ CONFIG_SND_SOC_RCAR=m
 CONFIG_SND_SOC_AK4613=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD=m
+CONFIG_I2C_HID=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
@@ -501,12 +486,12 @@ CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ACPI=y
-CONFIG_MMC_SDHCI_F_SDH30=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_OF_ARASAN=y
 CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_CADENCE=y
 CONFIG_MMC_SDHCI_TEGRA=y
+CONFIG_MMC_SDHCI_F_SDH30=y
 CONFIG_MMC_MESON_GX=y
 CONFIG_MMC_SDHCI_MSM=y
 CONFIG_MMC_SPI=y
@@ -524,11 +509,11 @@ CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_PWM=y
 CONFIG_LEDS_SYSCON=y
+CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
 CONFIG_LEDS_TRIGGER_PANIC=y
-CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_EDAC=y
 CONFIG_EDAC_GHES=y
 CONFIG_RTC_CLASS=y
@@ -537,13 +522,13 @@ CONFIG_RTC_DRV_RK808=m
 CONFIG_RTC_DRV_S5M=y
 CONFIG_RTC_DRV_DS3232=y
 CONFIG_RTC_DRV_EFI=y
+CONFIG_RTC_DRV_CROS_EC=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_RTC_DRV_PL031=y
 CONFIG_RTC_DRV_SUN6I=y
 CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_XGENE=y
-CONFIG_RTC_DRV_CROS_EC=y
 CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=m
 CONFIG_K3_DMA=y
@@ -579,7 +564,6 @@ CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_ARM_MHU=y
 CONFIG_PLATFORM_MHU=y
 CONFIG_BCM2835_MBOX=y
-CONFIG_HI6220_MBOX=y
 CONFIG_QCOM_APCS_IPC=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_SMMU=y
@@ -602,7 +586,6 @@ CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_EXTCON_USBC_CROS_EC=y
 CONFIG_MEMORY=y
-CONFIG_TEGRA_MC=y
 CONFIG_IIO=y
 CONFIG_EXYNOS_ADC=y
 CONFIG_ROCKCHIP_SARADC=m
@@ -618,27 +601,27 @@ CONFIG_PWM_RCAR=m
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_PWM_SAMSUNG=y
 CONFIG_PWM_TEGRA=m
+CONFIG_PHY_XGENE=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_HI6220_USB=y
 CONFIG_PHY_HISTB_COMBPHY=y
 CONFIG_PHY_HISI_INNO_USB2=y
-CONFIG_PHY_RCAR_GEN3_USB2=y
-CONFIG_PHY_RCAR_GEN3_USB3=m
-CONFIG_PHY_HI6220_USB=y
-CONFIG_PHY_QCOM_USB_HS=y
-CONFIG_PHY_SUN4I_USB=y
 CONFIG_PHY_MVEBU_CP110_COMPHY=y
 CONFIG_PHY_QCOM_QMP=m
-CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_QCOM_USB_HS=y
+CONFIG_PHY_RCAR_GEN3_USB2=y
+CONFIG_PHY_RCAR_GEN3_USB3=m
 CONFIG_PHY_ROCKCHIP_EMMC=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
 CONFIG_PHY_ROCKCHIP_PCIE=m
 CONFIG_PHY_ROCKCHIP_TYPEC=y
-CONFIG_PHY_XGENE=y
 CONFIG_PHY_TEGRA_XUSB=y
 CONFIG_QCOM_L2_PMU=y
 CONFIG_QCOM_L3_PMU=y
-CONFIG_MESON_EFUSE=m
 CONFIG_QCOM_QFPROM=y
 CONFIG_ROCKCHIP_EFUSE=y
 CONFIG_UNIPHIER_EFUSE=y
+CONFIG_MESON_EFUSE=m
 CONFIG_TEE=y
 CONFIG_OPTEE=y
 CONFIG_ARM_SCPI_PROTOCOL=y
@@ -647,7 +630,6 @@ CONFIG_EFI_CAPSULE_LOADER=y
 CONFIG_ACPI=y
 CONFIG_ACPI_APEI=y
 CONFIG_ACPI_APEI_GHES=y
-CONFIG_ACPI_APEI_PCIEAER=y
 CONFIG_ACPI_APEI_MEMORY_FAILURE=y
 CONFIG_ACPI_APEI_EINJ=y
 CONFIG_EXT2_FS=y
@@ -682,7 +664,6 @@ CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_LOCKUP_DETECTOR=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 # CONFIG_FTRACE is not set
@@ -691,20 +672,15 @@ CONFIG_SECURITY=y
 CONFIG_CRYPTO_ECHAINIV=y
 CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_ARM64_CRYPTO=y
-CONFIG_CRYPTO_SHA256_ARM64=m
-CONFIG_CRYPTO_SHA512_ARM64=m
 CONFIG_CRYPTO_SHA1_ARM64_CE=y
 CONFIG_CRYPTO_SHA2_ARM64_CE=y
-CONFIG_CRYPTO_GHASH_ARM64_CE=y
-CONFIG_CRYPTO_CRCT10DIF_ARM64_CE=m
-CONFIG_CRYPTO_CRC32_ARM64_CE=m
-CONFIG_CRYPTO_AES_ARM64=m
-CONFIG_CRYPTO_AES_ARM64_CE=m
-CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
-CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
-CONFIG_CRYPTO_AES_ARM64_NEON_BLK=m
-CONFIG_CRYPTO_CHACHA20_NEON=m
-CONFIG_CRYPTO_AES_ARM64_BS=m
 CONFIG_CRYPTO_SHA512_ARM64_CE=m
 CONFIG_CRYPTO_SHA3_ARM64=m
 CONFIG_CRYPTO_SM3_ARM64_CE=m
+CONFIG_CRYPTO_GHASH_ARM64_CE=y
+CONFIG_CRYPTO_CRCT10DIF_ARM64_CE=m
+CONFIG_CRYPTO_CRC32_ARM64_CE=m
+CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
+CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
+CONFIG_CRYPTO_CHACHA20_NEON=m
+CONFIG_CRYPTO_AES_ARM64_BS=m

arch/arm64/crypto/aes-glue.c

@@ -223,8 +223,8 @@ static int ctr_encrypt(struct skcipher_request *req)
 		kernel_neon_begin();
 		aes_ctr_encrypt(walk.dst.virt.addr, walk.src.virt.addr,
 				(u8 *)ctx->key_enc, rounds, blocks, walk.iv);
-		err = skcipher_walk_done(&walk, walk.nbytes % AES_BLOCK_SIZE);
 		kernel_neon_end();
+		err = skcipher_walk_done(&walk, walk.nbytes % AES_BLOCK_SIZE);
 	}
 	if (walk.nbytes) {
 		u8 __aligned(8) tail[AES_BLOCK_SIZE];

arch/arm64/include/asm/alternative.h

@@ -28,7 +28,12 @@ typedef void (*alternative_cb_t)(struct alt_instr *alt,
 				 __le32 *origptr, __le32 *updptr, int nr_inst);
 
 void __init apply_alternatives_all(void);
-void apply_alternatives(void *start, size_t length);
+
+#ifdef CONFIG_MODULES
+void apply_alternatives_module(void *start, size_t length);
+#else
+static inline void apply_alternatives_module(void *start, size_t length) { }
+#endif
 
 #define ALTINSTR_ENTRY(feature,cb)					      \
 	" .word 661b - .\n"				/* label           */ \

arch/arm64/include/asm/kvm_host.h

@@ -306,6 +306,7 @@ struct kvm_vcpu_arch {
 #define KVM_ARM64_FP_ENABLED		(1 << 1) /* guest FP regs loaded */
 #define KVM_ARM64_FP_HOST		(1 << 2) /* host FP regs loaded */
 #define KVM_ARM64_HOST_SVE_IN_USE	(1 << 3) /* backup for host TIF_SVE */
+#define KVM_ARM64_HOST_SVE_ENABLED	(1 << 4) /* SVE enabled for EL0 */
 
 #define vcpu_gp_regs(v)		(&(v)->arch.ctxt.gp_regs)
 

arch/arm64/include/asm/pgtable.h

@@ -224,10 +224,8 @@ static inline void set_pte(pte_t *ptep, pte_t pte)
 	 * Only if the new pte is valid and kernel, otherwise TLB maintenance
 	 * or update_mmu_cache() have the necessary barriers.
 	 */
-	if (pte_valid_not_user(pte)) {
+	if (pte_valid_not_user(pte))
 		dsb(ishst);
-		isb();
-	}
 }
 
 extern void __sync_icache_dcache(pte_t pteval);
@@ -434,7 +432,6 @@ static inline void set_pmd(pmd_t *pmdp, pmd_t pmd)
 {
 	WRITE_ONCE(*pmdp, pmd);
 	dsb(ishst);
-	isb();
 }
 
 static inline void pmd_clear(pmd_t *pmdp)
@@ -485,7 +482,6 @@ static inline void set_pud(pud_t *pudp, pud_t pud)
 {
 	WRITE_ONCE(*pudp, pud);
 	dsb(ishst);
-	isb();
 }
 
 static inline void pud_clear(pud_t *pudp)

arch/arm64/include/asm/sysreg.h

@@ -728,6 +728,17 @@ asm(
 	asm volatile("msr_s " __stringify(r) ", %x0" : : "rZ" (__val));	\
 } while (0)
 
+/*
+ * Modify bits in a sysreg. Bits in the clear mask are zeroed, then bits in the
+ * set mask are set. Other bits are left as-is.
+ */
+#define sysreg_clear_set(sysreg, clear, set) do {			\
+	u64 __scs_val = read_sysreg(sysreg);				\
+	u64 __scs_new = (__scs_val & ~(u64)(clear)) | (set);		\
+	if (__scs_new != __scs_val)					\
+		write_sysreg(__scs_new, sysreg);			\
+} while (0)
+
 static inline void config_sctlr_el1(u32 clear, u32 set)
 {
 	u32 val;

arch/arm64/kernel/alternative.c

@@ -122,7 +122,30 @@ static void patch_alternative(struct alt_instr *alt,
 	}
 }
 
-static void __apply_alternatives(void *alt_region, bool use_linear_alias)
+/*
+ * We provide our own, private D-cache cleaning function so that we don't
+ * accidentally call into the cache.S code, which is patched by us at
+ * runtime.
+ */
+static void clean_dcache_range_nopatch(u64 start, u64 end)
+{
+	u64 cur, d_size, ctr_el0;
+
+	ctr_el0 = read_sanitised_ftr_reg(SYS_CTR_EL0);
+	d_size = 4 << cpuid_feature_extract_unsigned_field(ctr_el0,
+							   CTR_DMINLINE_SHIFT);
+	cur = start & ~(d_size - 1);
+	do {
+		/*
+		 * We must clean+invalidate to the PoC in order to avoid
+		 * Cortex-A53 errata 826319, 827319, 824069 and 819472
+		 * (this corresponds to ARM64_WORKAROUND_CLEAN_CACHE)
+		 */
+		asm volatile("dc civac, %0" : : "r" (cur) : "memory");
+	} while (cur += d_size, cur < end);
+}
+
+static void __apply_alternatives(void *alt_region, bool is_module)
 {
 	struct alt_instr *alt;
 	struct alt_region *region = alt_region;
@@ -145,7 +168,7 @@ static void __apply_alternatives(void *alt_region, bool use_linear_alias)
 		pr_info_once("patching kernel code\n");
 
 		origptr = ALT_ORIG_PTR(alt);
-		updptr = use_linear_alias ? lm_alias(origptr) : origptr;
+		updptr = is_module ? origptr : lm_alias(origptr);
 		nr_inst = alt->orig_len / AARCH64_INSN_SIZE;
 
 		if (alt->cpufeature < ARM64_CB_PATCH)
@@ -155,8 +178,20 @@ static void __apply_alternatives(void *alt_region, bool use_linear_alias)
 
 		alt_cb(alt, origptr, updptr, nr_inst);
 
-		flush_icache_range((uintptr_t)origptr,
+		if (!is_module) {
-				   (uintptr_t)(origptr + nr_inst));
+			clean_dcache_range_nopatch((u64)origptr,
+						   (u64)(origptr + nr_inst));
+		}
+	}
+
+	/*
+	 * The core module code takes care of cache maintenance in
+	 * flush_module_icache().
+	 */
+	if (!is_module) {
+		dsb(ish);
+		__flush_icache_all();
+		isb();
 	}
 }
 
@@ -178,7 +213,7 @@ static int __apply_alternatives_multi_stop(void *unused)
 		isb();
 	} else {
 		BUG_ON(alternatives_applied);
-		__apply_alternatives(&region, true);
+		__apply_alternatives(&region, false);
 		/* Barriers provided by the cache flushing */
 		WRITE_ONCE(alternatives_applied, 1);
 	}
@@ -192,12 +227,14 @@ void __init apply_alternatives_all(void)
 	stop_machine(__apply_alternatives_multi_stop, NULL, cpu_online_mask);
 }
 
-void apply_alternatives(void *start, size_t length)
+#ifdef CONFIG_MODULES
+void apply_alternatives_module(void *start, size_t length)
 {
 	struct alt_region region = {
 		.begin	= start,
 		.end	= start + length,
 	};
 
-	__apply_alternatives(&region, false);
+	__apply_alternatives(&region, true);
 }
+#endif

arch/arm64/kernel/cpufeature.c

@@ -937,7 +937,7 @@ static int __init parse_kpti(char *str)
 	__kpti_forced = enabled ? 1 : -1;
 	return 0;
 }
-__setup("kpti=", parse_kpti);
+early_param("kpti", parse_kpti);
 #endif	/* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 #ifdef CONFIG_ARM64_HW_AFDBM

arch/arm64/kernel/module.c

@@ -448,9 +448,8 @@ int module_finalize(const Elf_Ehdr *hdr,
 	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
 
 	for (s = sechdrs, se = sechdrs + hdr->e_shnum; s < se; s++) {
-		if (strcmp(".altinstructions", secstrs + s->sh_name) == 0) {
+		if (strcmp(".altinstructions", secstrs + s->sh_name) == 0)
-			apply_alternatives((void *)s->sh_addr, s->sh_size);
+			apply_alternatives_module((void *)s->sh_addr, s->sh_size);
-		}
 #ifdef CONFIG_ARM64_MODULE_PLTS
 		if (IS_ENABLED(CONFIG_DYNAMIC_FTRACE) &&
 		    !strcmp(".text.ftrace_trampoline", secstrs + s->sh_name))

arch/arm64/kernel/smp.c

@@ -179,7 +179,7 @@ int __cpu_up(unsigned int cpu, struct task_struct *idle)
  * This is the secondary CPU boot entry.  We're using this CPUs
  * idle thread stack, but a set of temporary page tables.
  */
-asmlinkage void secondary_start_kernel(void)
+asmlinkage notrace void secondary_start_kernel(void)
 {
 	u64 mpidr = read_cpuid_mpidr() & MPIDR_HWID_BITMASK;
 	struct mm_struct *mm = &init_mm;

arch/arm64/kvm/fpsimd.c

@@ -5,13 +5,14 @@
  * Copyright 2018 Arm Limited
  * Author: Dave Martin <Dave.Martin@arm.com>
  */
-#include <linux/bottom_half.h>
+#include <linux/irqflags.h>
 #include <linux/sched.h>
 #include <linux/thread_info.h>
 #include <linux/kvm_host.h>
 #include <asm/kvm_asm.h>
 #include <asm/kvm_host.h>
 #include <asm/kvm_mmu.h>
+#include <asm/sysreg.h>
 
 /*
  * Called on entry to KVM_RUN unless this vcpu previously ran at least
@@ -61,10 +62,16 @@ void kvm_arch_vcpu_load_fp(struct kvm_vcpu *vcpu)
 {
 	BUG_ON(!current->mm);
 
-	vcpu->arch.flags &= ~(KVM_ARM64_FP_ENABLED | KVM_ARM64_HOST_SVE_IN_USE);
+	vcpu->arch.flags &= ~(KVM_ARM64_FP_ENABLED |
+			      KVM_ARM64_HOST_SVE_IN_USE |
+			      KVM_ARM64_HOST_SVE_ENABLED);
 	vcpu->arch.flags |= KVM_ARM64_FP_HOST;
+
 	if (test_thread_flag(TIF_SVE))
 		vcpu->arch.flags |= KVM_ARM64_HOST_SVE_IN_USE;
+
+	if (read_sysreg(cpacr_el1) & CPACR_EL1_ZEN_EL0EN)
+		vcpu->arch.flags |= KVM_ARM64_HOST_SVE_ENABLED;
 }
 
 /*
@@ -92,19 +99,30 @@ void kvm_arch_vcpu_ctxsync_fp(struct kvm_vcpu *vcpu)
  */
 void kvm_arch_vcpu_put_fp(struct kvm_vcpu *vcpu)
 {
-	local_bh_disable();
+	unsigned long flags;
 
-	update_thread_flag(TIF_SVE,
+	local_irq_save(flags);
-			   vcpu->arch.flags & KVM_ARM64_HOST_SVE_IN_USE);
 
 	if (vcpu->arch.flags & KVM_ARM64_FP_ENABLED) {
 		/* Clean guest FP state to memory and invalidate cpu view */
 		fpsimd_save();
 		fpsimd_flush_cpu_state();
-	} else if (!test_thread_flag(TIF_FOREIGN_FPSTATE)) {
+	} else if (system_supports_sve()) {
-		/* Ensure user trap controls are correctly restored */
+		/*
-		fpsimd_bind_task_to_cpu();
+		 * The FPSIMD/SVE state in the CPU has not been touched, and we
+		 * have SVE (and VHE): CPACR_EL1 (alias CPTR_EL2) has been
+		 * reset to CPACR_EL1_DEFAULT by the Hyp code, disabling SVE
+		 * for EL0.  To avoid spurious traps, restore the trap state
+		 * seen by kvm_arch_vcpu_load_fp():
+		 */
+		if (vcpu->arch.flags & KVM_ARM64_HOST_SVE_ENABLED)
+			sysreg_clear_set(CPACR_EL1, 0, CPACR_EL1_ZEN_EL0EN);
+		else
+			sysreg_clear_set(CPACR_EL1, CPACR_EL1_ZEN_EL0EN, 0);
 	}
 
-	local_bh_enable();
+	update_thread_flag(TIF_SVE,
+			   vcpu->arch.flags & KVM_ARM64_HOST_SVE_IN_USE);
+
+	local_irq_restore(flags);
 }

arch/arm64/mm/dma-mapping.c

@@ -583,13 +583,14 @@ static void *__iommu_alloc_attrs(struct device *dev, size_t size,
 						    size >> PAGE_SHIFT);
 			return NULL;
 		}
-		if (!coherent)
-			__dma_flush_area(page_to_virt(page), iosize);
-
 		addr = dma_common_contiguous_remap(page, size, VM_USERMAP,
 						   prot,
 						   __builtin_return_address(0));
-		if (!addr) {
+		if (addr) {
+			memset(addr, 0, size);
+			if (!coherent)
+				__dma_flush_area(page_to_virt(page), iosize);
+		} else {
 			iommu_dma_unmap_page(dev, *handle, iosize, 0, attrs);
 			dma_release_from_contiguous(dev, page,
 						    size >> PAGE_SHIFT);

arch/arm64/mm/proc.S

@@ -217,8 +217,9 @@ ENDPROC(idmap_cpu_replace_ttbr1)
 
 	.macro __idmap_kpti_put_pgtable_ent_ng, type
 	orr	\type, \type, #PTE_NG		// Same bit for blocks and pages
-	str	\type, [cur_\()\type\()p]	// Update the entry and ensure it
+	str	\type, [cur_\()\type\()p]	// Update the entry and ensure
-	dc	civac, cur_\()\type\()p		// is visible to all CPUs.
+	dmb	sy				// that it is visible to all
+	dc	civac, cur_\()\type\()p		// CPUs.
 	.endm
 
 /*

arch/microblaze/Kconfig.debug

@@ -8,11 +8,4 @@ config TRACE_IRQFLAGS_SUPPORT
 
 source "lib/Kconfig.debug"
 
-config HEART_BEAT
-	bool "Heart beat function for kernel"
-	default n
-	help
-	  This option turns on/off heart beat kernel functionality.
-	  First GPIO node is taken.
-
 endmenu

arch/microblaze/include/asm/setup.h

@@ -19,15 +19,10 @@ extern char cmd_line[COMMAND_LINE_SIZE];
 
 extern char *klimit;
 
-void microblaze_heartbeat(void);
-void microblaze_setup_heartbeat(void);
-
 #   ifdef CONFIG_MMU
 extern void mmu_reset(void);
 #   endif /* CONFIG_MMU */
 
-extern void of_platform_reset_gpio_probe(void);
-
 void time_init(void);
 void init_IRQ(void);
 void machine_early_init(const char *cmdline, unsigned int ram,

arch/microblaze/include/asm/unistd.h

@@ -38,6 +38,6 @@
 
 #endif /* __ASSEMBLY__ */
 
-#define __NR_syscalls         399
+#define __NR_syscalls         401
 
 #endif /* _ASM_MICROBLAZE_UNISTD_H */

arch/microblaze/include/uapi/asm/unistd.h

@@ -415,5 +415,7 @@
 #define __NR_pkey_alloc		396
 #define __NR_pkey_free		397
 #define __NR_statx		398
+#define __NR_io_pgetevents	399
+#define __NR_rseq		400
 
 #endif /* _UAPI_ASM_MICROBLAZE_UNISTD_H */

arch/microblaze/kernel/Makefile

@@ -8,7 +8,6 @@ ifdef CONFIG_FUNCTION_TRACER
 CFLAGS_REMOVE_timer.o = -pg
 CFLAGS_REMOVE_intc.o = -pg
 CFLAGS_REMOVE_early_printk.o = -pg
-CFLAGS_REMOVE_heartbeat.o = -pg
 CFLAGS_REMOVE_ftrace.o = -pg
 CFLAGS_REMOVE_process.o = -pg
 endif
@@ -17,12 +16,11 @@ extra-y := head.o vmlinux.lds
 
 obj-y += dma.o exceptions.o \
 	hw_exception_handler.o irq.o \
-	platform.o process.o prom.o ptrace.o \
+	process.o prom.o ptrace.o \
 	reset.o setup.o signal.o sys_microblaze.o timer.o traps.o unwind.o
 
 obj-y += cpu/
 
-obj-$(CONFIG_HEART_BEAT)	+= heartbeat.o
 obj-$(CONFIG_MODULES)		+= microblaze_ksyms.o module.o
 obj-$(CONFIG_MMU)		+= misc.o
 obj-$(CONFIG_STACKTRACE)	+= stacktrace.o

arch/microblaze/kernel/heartbeat.c

@@ -1,72 +0,0 @@
-/*
- * Copyright (C) 2007-2009 Michal Simek <monstr@monstr.eu>
- * Copyright (C) 2007-2009 PetaLogix
- * Copyright (C) 2006 Atmark Techno, Inc.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/sched.h>
-#include <linux/sched/loadavg.h>
-#include <linux/io.h>
-
-#include <asm/setup.h>
-#include <asm/page.h>
-#include <asm/prom.h>
-
-static unsigned int base_addr;
-
-void microblaze_heartbeat(void)
-{
-	static unsigned int cnt, period, dist;
-
-	if (base_addr) {
-		if (cnt == 0 || cnt == dist)
-			out_be32(base_addr, 1);
-		else if (cnt == 7 || cnt == dist + 7)
-			out_be32(base_addr, 0);
-
-		if (++cnt > period) {
-			cnt = 0;
-			/*
-			 * The hyperbolic function below modifies the heartbeat
-			 * period length in dependency of the current (5min)
-			 * load. It goes through the points f(0)=126, f(1)=86,
-			 * f(5)=51, f(inf)->30.
-			 */
-			period = ((672 << FSHIFT) / (5 * avenrun[0] +
-						(7 << FSHIFT))) + 30;
-			dist = period / 4;
-		}
-	}
-}
-
-void microblaze_setup_heartbeat(void)
-{
-	struct device_node *gpio = NULL;
-	int *prop;
-	int j;
-	const char * const gpio_list[] = {
-		"xlnx,xps-gpio-1.00.a",
-		NULL
-	};
-
-	for (j = 0; gpio_list[j] != NULL; j++) {
-		gpio = of_find_compatible_node(NULL, NULL, gpio_list[j]);
-		if (gpio)
-			break;
-	}
-
-	if (gpio) {
-		base_addr = be32_to_cpup(of_get_property(gpio, "reg", NULL));
-		base_addr = (unsigned long) ioremap(base_addr, PAGE_SIZE);
-		pr_notice("Heartbeat GPIO at 0x%x\n", base_addr);
-
-		/* GPIO is configured as output */
-		prop = (int *) of_get_property(gpio, "xlnx,is-bidir", NULL);
-		if (prop)
-			out_be32(base_addr + 4, 0);
-	}
-}

arch/microblaze/kernel/platform.c

@@ -1,29 +0,0 @@
-/*
- * Copyright 2008 Michal Simek <monstr@monstr.eu>
- *
- * based on virtex.c file
- *
- * Copyright 2007 Secret Lab Technologies Ltd.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/init.h>
-#include <linux/of_platform.h>
-#include <asm/setup.h>
-
-static struct of_device_id xilinx_of_bus_ids[] __initdata = {
-	{ .compatible = "simple-bus", },
-	{ .compatible = "xlnx,compound", },
-	{}
-};
-
-static int __init microblaze_device_probe(void)
-{
-	of_platform_bus_probe(NULL, xilinx_of_bus_ids, NULL);
-	of_platform_reset_gpio_probe();
-	return 0;
-}
-device_initcall(microblaze_device_probe);

arch/microblaze/kernel/reset.c

@@ -18,7 +18,7 @@
 static int handle; /* reset pin handle */
 static unsigned int reset_val;
 
-void of_platform_reset_gpio_probe(void)
+static int of_platform_reset_gpio_probe(void)
 {
 	int ret;
 	handle = of_get_named_gpio(of_find_node_by_path("/"),
@@ -27,13 +27,13 @@ void of_platform_reset_gpio_probe(void)
 	if (!gpio_is_valid(handle)) {
 		pr_info("Skipping unavailable RESET gpio %d (%s)\n",
 				handle, "reset");
-		return;
+		return -ENODEV;
 	}
 
 	ret = gpio_request(handle, "reset");
 	if (ret < 0) {
 		pr_info("GPIO pin is already allocated\n");
-		return;
+		return ret;
 	}
 
 	/* get current setup value */
@@ -51,11 +51,12 @@ void of_platform_reset_gpio_probe(void)
 
 	pr_info("RESET: Registered gpio device: %d, current val: %d\n",
 							handle, reset_val);
-	return;
+	return 0;
 err:
 	gpio_free(handle);
-	return;
+	return ret;
 }
+device_initcall(of_platform_reset_gpio_probe);
 
 
 static void gpio_system_reset(void)

arch/microblaze/kernel/syscall_table.S

@@ -400,3 +400,5 @@ ENTRY(sys_call_table)
 	.long sys_pkey_alloc
 	.long sys_pkey_free
 	.long sys_statx
+	.long sys_io_pgetevents
+	.long sys_rseq

arch/microblaze/kernel/timer.c

@@ -156,9 +156,6 @@ static inline void timer_ack(void)
 static irqreturn_t timer_interrupt(int irq, void *dev_id)
 {
 	struct clock_event_device *evt = &clockevent_xilinx_timer;
-#ifdef CONFIG_HEART_BEAT
-	microblaze_heartbeat();
-#endif
 	timer_ack();
 	evt->event_handler(evt);
 	return IRQ_HANDLED;
@@ -318,10 +315,6 @@ static int __init xilinx_timer_init(struct device_node *timer)
 		return ret;
 	}
 
-#ifdef CONFIG_HEART_BEAT
-	microblaze_setup_heartbeat();
-#endif
-
 	ret = xilinx_clocksource_init();
 	if (ret)
 		return ret;

arch/mips/Kconfig

@@ -65,6 +65,7 @@ config MIPS
 	select HAVE_OPROFILE
 	select HAVE_PERF_EVENTS
 	select HAVE_REGS_AND_STACK_ACCESS_API
+	select HAVE_RSEQ
 	select HAVE_STACKPROTECTOR
 	select HAVE_SYSCALL_TRACEPOINTS
 	select HAVE_VIRT_CPU_ACCOUNTING_GEN if 64BIT || !SMP

arch/mips/ath79/mach-pb44.c

@@ -34,7 +34,7 @@
 #define PB44_KEYS_DEBOUNCE_INTERVAL	(3 * PB44_KEYS_POLL_INTERVAL)
 
 static struct gpiod_lookup_table pb44_i2c_gpiod_table = {
-	.dev_id = "i2c-gpio",
+	.dev_id = "i2c-gpio.0",
 	.table = {
 		GPIO_LOOKUP_IDX("ath79-gpio", PB44_GPIO_I2C_SDA,
 				NULL, 0, GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),

arch/mips/bcm47xx/setup.c

@@ -212,6 +212,12 @@ static int __init bcm47xx_cpu_fixes(void)
 		 */
 		if (bcm47xx_bus.bcma.bus.chipinfo.id == BCMA_CHIP_ID_BCM4706)
 			cpu_wait = NULL;
+
+		/*
+		 * BCM47XX Erratum "R10: PCIe Transactions Periodically Fail"
+		 * Enable ExternalSync for sync instruction to take effect
+		 */
+		set_c0_config7(MIPS_CONF7_ES);
 		break;
 #endif
 	}

arch/mips/include/asm/io.h

@@ -414,6 +414,8 @@ static inline type pfx##in##bwlq##p(unsigned long port)			\
 	__val = *__addr;						\
 	slow;								\
 									\
+	/* prevent prefetching of coherent DMA data prematurely */	\
+	rmb();								\
 	return pfx##ioswab##bwlq(__addr, __val);			\
 }
 

arch/mips/include/asm/mipsregs.h

@@ -681,6 +681,8 @@
 #define MIPS_CONF7_WII		(_ULCAST_(1) << 31)
 
 #define MIPS_CONF7_RPS		(_ULCAST_(1) << 2)
+/* ExternalSync */
+#define MIPS_CONF7_ES		(_ULCAST_(1) << 8)
 
 #define MIPS_CONF7_IAR		(_ULCAST_(1) << 10)
 #define MIPS_CONF7_AR		(_ULCAST_(1) << 16)
@@ -2765,6 +2767,7 @@ __BUILD_SET_C0(status)
 __BUILD_SET_C0(cause)
 __BUILD_SET_C0(config)
 __BUILD_SET_C0(config5)
+__BUILD_SET_C0(config7)
 __BUILD_SET_C0(intcontrol)
 __BUILD_SET_C0(intctl)
 __BUILD_SET_C0(srsmap)

arch/mips/include/uapi/asm/unistd.h

@@ -388,17 +388,19 @@
 #define __NR_pkey_alloc			(__NR_Linux + 364)
 #define __NR_pkey_free			(__NR_Linux + 365)
 #define __NR_statx			(__NR_Linux + 366)
+#define __NR_rseq			(__NR_Linux + 367)
+#define __NR_io_pgetevents		(__NR_Linux + 368)
 
 
 /*
  * Offset of the last Linux o32 flavoured syscall
  */
-#define __NR_Linux_syscalls		366
+#define __NR_Linux_syscalls		368
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
 
 #define __NR_O32_Linux			4000
-#define __NR_O32_Linux_syscalls		366
+#define __NR_O32_Linux_syscalls		368
 
 #if _MIPS_SIM == _MIPS_SIM_ABI64
 
@@ -733,16 +735,18 @@
 #define __NR_pkey_alloc			(__NR_Linux + 324)
 #define __NR_pkey_free			(__NR_Linux + 325)
 #define __NR_statx			(__NR_Linux + 326)
+#define __NR_rseq			(__NR_Linux + 327)
+#define __NR_io_pgetevents		(__NR_Linux + 328)
 
 /*
  * Offset of the last Linux 64-bit flavoured syscall
  */
-#define __NR_Linux_syscalls		326
+#define __NR_Linux_syscalls		328
 
 #endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
 
 #define __NR_64_Linux			5000
-#define __NR_64_Linux_syscalls		326
+#define __NR_64_Linux_syscalls		328
 
 #if _MIPS_SIM == _MIPS_SIM_NABI32
 
@@ -1081,15 +1085,17 @@
 #define __NR_pkey_alloc			(__NR_Linux + 328)
 #define __NR_pkey_free			(__NR_Linux + 329)
 #define __NR_statx			(__NR_Linux + 330)
+#define __NR_rseq			(__NR_Linux + 331)
+#define __NR_io_pgetevents		(__NR_Linux + 332)
 
 /*
  * Offset of the last N32 flavoured syscall
  */
-#define __NR_Linux_syscalls		330
+#define __NR_Linux_syscalls		332
 
 #endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */
 
 #define __NR_N32_Linux			6000
-#define __NR_N32_Linux_syscalls		330
+#define __NR_N32_Linux_syscalls		332
 
 #endif /* _UAPI_ASM_UNISTD_H */

arch/mips/kernel/entry.S

@@ -79,6 +79,10 @@ FEXPORT(ret_from_fork)
 	jal	schedule_tail		# a0 = struct task_struct *prev
 
 FEXPORT(syscall_exit)
+#ifdef CONFIG_DEBUG_RSEQ
+	move	a0, sp
+	jal	rseq_syscall
+#endif
 	local_irq_disable		# make sure need_resched and
 					# signals dont change between
 					# sampling and return
@@ -141,6 +145,10 @@ work_notifysig:				# deal with pending signals and
 	j	resume_userspace_check
 
 FEXPORT(syscall_exit_partial)
+#ifdef CONFIG_DEBUG_RSEQ
+	move	a0, sp
+	jal	rseq_syscall
+#endif
 	local_irq_disable		# make sure need_resched doesn't
 					# change between and return
 	LONG_L	a2, TI_FLAGS($28)	# current->work

arch/mips/kernel/mcount.S

@@ -119,10 +119,20 @@ NESTED(_mcount, PT_SIZE, ra)
 EXPORT_SYMBOL(_mcount)
 	PTR_LA	t1, ftrace_stub
 	PTR_L	t2, ftrace_trace_function /* Prepare t2 for (1) */
-	bne	t1, t2, static_trace
+	beq	t1, t2, fgraph_trace
 	 nop
 
+	MCOUNT_SAVE_REGS
+
+	move	a0, ra		/* arg1: self return address */
+	jalr	t2		/* (1) call *ftrace_trace_function */
+	 move	a1, AT		/* arg2: parent's return address */
+
+	MCOUNT_RESTORE_REGS
+
+fgraph_trace:
 #ifdef	CONFIG_FUNCTION_GRAPH_TRACER
+	PTR_LA	t1, ftrace_stub
 	PTR_L	t3, ftrace_graph_return
 	bne	t1, t3, ftrace_graph_caller
 	 nop
@@ -131,24 +141,11 @@ EXPORT_SYMBOL(_mcount)
 	bne	t1, t3, ftrace_graph_caller
 	 nop
 #endif
-	b	ftrace_stub
-#ifdef CONFIG_32BIT
-	 addiu sp, sp, 8
-#else
-	 nop
-#endif
 
-static_trace:
-	MCOUNT_SAVE_REGS
-
-	move	a0, ra		/* arg1: self return address */
-	jalr	t2		/* (1) call *ftrace_trace_function */
-	 move	a1, AT		/* arg2: parent's return address */
-
-	MCOUNT_RESTORE_REGS
 #ifdef CONFIG_32BIT
 	addiu sp, sp, 8
 #endif
+
 	.globl ftrace_stub
 ftrace_stub:
 	RETURN_BACK

arch/mips/kernel/scall32-o32.S

@@ -590,3 +590,5 @@ EXPORT(sys_call_table)
 	PTR	sys_pkey_alloc
 	PTR	sys_pkey_free			/* 4365 */
 	PTR	sys_statx
+	PTR	sys_rseq
+	PTR	sys_io_pgetevents

arch/mips/kernel/scall64-64.S

@@ -439,4 +439,6 @@ EXPORT(sys_call_table)
 	PTR	sys_pkey_alloc
 	PTR	sys_pkey_free			/* 5325 */
 	PTR	sys_statx
+	PTR	sys_rseq
+	PTR	sys_io_pgetevents
 	.size	sys_call_table,.-sys_call_table

arch/mips/kernel/scall64-n32.S

@@ -434,4 +434,6 @@ EXPORT(sysn32_call_table)
 	PTR	sys_pkey_alloc
 	PTR	sys_pkey_free
 	PTR	sys_statx			/* 6330 */
+	PTR	sys_rseq
+	PTR	compat_sys_io_pgetevents
 	.size	sysn32_call_table,.-sysn32_call_table

arch/mips/kernel/scall64-o32.S

@@ -583,4 +583,6 @@ EXPORT(sys32_call_table)
 	PTR	sys_pkey_alloc
 	PTR	sys_pkey_free			/* 4365 */
 	PTR	sys_statx
+	PTR	sys_rseq
+	PTR	compat_sys_io_pgetevents
 	.size	sys32_call_table,.-sys32_call_table

arch/mips/kernel/signal.c

@@ -801,6 +801,8 @@ static void handle_signal(struct ksignal *ksig, struct pt_regs *regs)
 		regs->regs[0] = 0;		/* Don't deal with this again.	*/
 	}
 
+	rseq_signal_deliver(ksig, regs);
+
 	if (sig_uses_siginfo(&ksig->ka, abi))
 		ret = abi->setup_rt_frame(vdso + abi->vdso->off_rt_sigreturn,
 					  ksig, regs, oldset);
@@ -868,6 +870,7 @@ asmlinkage void do_notify_resume(struct pt_regs *regs, void *unused,
 	if (thread_info_flags & _TIF_NOTIFY_RESUME) {
 		clear_thread_flag(TIF_NOTIFY_RESUME);
 		tracehook_notify_resume(regs);
+		rseq_handle_notify_resume(NULL, regs);
 	}
 
 	user_enter();

arch/parisc/Kconfig

@@ -244,11 +244,11 @@ config PARISC_PAGE_SIZE_4KB
 
 config PARISC_PAGE_SIZE_16KB
 	bool "16KB"
-	depends on PA8X00
+	depends on PA8X00 && BROKEN
 
 config PARISC_PAGE_SIZE_64KB
 	bool "64KB"
-	depends on PA8X00
+	depends on PA8X00 && BROKEN
 
 endchoice
 
@@ -347,7 +347,7 @@ config NR_CPUS
 	int "Maximum number of CPUs (2-32)"
 	range 2 32
 	depends on SMP
-	default "32"
+	default "4"
 
 endmenu
 

arch/parisc/Makefile

@@ -65,10 +65,6 @@ endif
 # kernel.
 cflags-y	+= -mdisable-fpregs
 
-# Without this, "ld -r" results in .text sections that are too big
-# (> 0x40000) for branches to reach stubs.
-cflags-y	+= -ffunction-sections
-
 # Use long jumps instead of long branches (needed if your linker fails to
 # link a too big vmlinux executable). Not enabled for building modules.
 ifdef CONFIG_MLONGCALLS

arch/parisc/include/asm/signal.h

@@ -21,14 +21,6 @@ typedef struct {
 	unsigned long sig[_NSIG_WORDS];
 } sigset_t;
 
-#ifndef __KERNEL__
-struct sigaction {
-	__sighandler_t sa_handler;
-	unsigned long sa_flags;
-	sigset_t sa_mask;		/* mask last for extensibility */
-};
-#endif
-
 #include <asm/sigcontext.h>
 
 #endif /* !__ASSEMBLY */

arch/parisc/include/uapi/asm/unistd.h

@@ -364,8 +364,9 @@
 #define __NR_preadv2		(__NR_Linux + 347)
 #define __NR_pwritev2		(__NR_Linux + 348)
 #define __NR_statx		(__NR_Linux + 349)
+#define __NR_io_pgetevents	(__NR_Linux + 350)
 
-#define __NR_Linux_syscalls	(__NR_statx + 1)
+#define __NR_Linux_syscalls	(__NR_io_pgetevents + 1)
 
 
 #define __IGNORE_select		/* newselect */

arch/parisc/kernel/drivers.c

@@ -154,17 +154,14 @@ int register_parisc_driver(struct parisc_driver *driver)
 {
 	/* FIXME: we need this because apparently the sti
 	 * driver can be registered twice */
-	if(driver->drv.name) {
+	if (driver->drv.name) {
-		printk(KERN_WARNING 
+		pr_warn("BUG: skipping previously registered driver %s\n",
-		       "BUG: skipping previously registered driver %s\n",
+			driver->name);
-		       driver->name);
 		return 1;
 	}
 
 	if (!driver->probe) {
-		printk(KERN_WARNING 
+		pr_warn("BUG: driver %s has no probe routine\n", driver->name);
-		       "BUG: driver %s has no probe routine\n",
-		       driver->name);
 		return 1;
 	}
 
@@ -491,12 +488,9 @@ alloc_pa_dev(unsigned long hpa, struct hardware_path *mod_path)
 
 	dev = create_parisc_device(mod_path);
 	if (dev->id.hw_type != HPHW_FAULTY) {
-		printk(KERN_ERR "Two devices have hardware path [%s].  "
+		pr_err("Two devices have hardware path [%s].  IODC data for second device: %7phN\n"
-				"IODC data for second device: "
+		       "Rearranging GSC cards sometimes helps\n",
-				"%02x%02x%02x%02x%02x%02x\n"
+			parisc_pathname(dev), iodc_data);
-				"Rearranging GSC cards sometimes helps\n",
-			parisc_pathname(dev), iodc_data[0], iodc_data[1],
-			iodc_data[3], iodc_data[4], iodc_data[5], iodc_data[6]);
 		return NULL;
 	}
 
@@ -528,8 +522,7 @@ alloc_pa_dev(unsigned long hpa, struct hardware_path *mod_path)
 	 * the keyboard controller
 	 */
 	if ((hpa & 0xfff) == 0 && insert_resource(&iomem_resource, &dev->hpa))
-		printk("Unable to claim HPA %lx for device %s\n",
+		pr_warn("Unable to claim HPA %lx for device %s\n", hpa, name);
-				hpa, name);
 
 	return dev;
 }
@@ -875,7 +868,7 @@ static void print_parisc_device(struct parisc_device *dev)
 	static int count;
 
 	print_pa_hwpath(dev, hw_path);
-	printk(KERN_INFO "%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
+	pr_info("%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
 		++count, dev->name, (void*) dev->hpa.start, hw_path, dev->id.hw_type,
 		dev->id.hversion_rev, dev->id.hversion, dev->id.sversion);
 

arch/parisc/kernel/syscall_table.S

@@ -445,6 +445,7 @@
 	ENTRY_COMP(preadv2)
 	ENTRY_COMP(pwritev2)
 	ENTRY_SAME(statx)
+	ENTRY_COMP(io_pgetevents)	/* 350 */
 
 
 .ifne (. - 90b) - (__NR_Linux_syscalls * (91b - 90b))

arch/parisc/kernel/unwind.c

@@ -25,7 +25,7 @@
 
 /* #define DEBUG 1 */
 #ifdef DEBUG
-#define dbg(x...) printk(x)
+#define dbg(x...) pr_debug(x)
 #else
 #define dbg(x...)
 #endif
@@ -182,7 +182,7 @@ int __init unwind_init(void)
 	start = (long)&__start___unwind[0];
 	stop = (long)&__stop___unwind[0];
 
-	printk("unwind_init: start = 0x%lx, end = 0x%lx, entries = %lu\n", 
+	dbg("unwind_init: start = 0x%lx, end = 0x%lx, entries = %lu\n",
 	    start, stop,
 	    (stop - start) / sizeof(struct unwind_table_entry));
 

arch/powerpc/Makefile

@@ -244,6 +244,7 @@ cpu-as-$(CONFIG_4xx)		+= -Wa,-m405
 cpu-as-$(CONFIG_ALTIVEC)	+= $(call as-option,-Wa$(comma)-maltivec)
 cpu-as-$(CONFIG_E200)		+= -Wa,-me200
 cpu-as-$(CONFIG_PPC_BOOK3S_64)	+= -Wa,-mpower4
+cpu-as-$(CONFIG_PPC_E500MC)	+= $(call as-option,-Wa$(comma)-me500mc)
 
 KBUILD_AFLAGS += $(cpu-as-y)
 KBUILD_CFLAGS += $(cpu-as-y)

arch/powerpc/include/asm/book3s/32/pgalloc.h

@@ -108,6 +108,7 @@ static inline void pgtable_free(void *table, unsigned index_size)
 }
 
 #define check_pgt_cache()	do { } while (0)
+#define get_hugepd_cache_index(x)  (x)
 
 #ifdef CONFIG_SMP
 static inline void pgtable_free_tlb(struct mmu_gather *tlb,
@@ -137,7 +138,6 @@ static inline void pgtable_free_tlb(struct mmu_gather *tlb,
 static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t table,
 				  unsigned long address)
 {
-	pgtable_page_dtor(table);
 	pgtable_free_tlb(tlb, page_address(table), 0);
 }
 #endif /* _ASM_POWERPC_BOOK3S_32_PGALLOC_H */

arch/powerpc/include/asm/book3s/64/pgtable-4k.h

@@ -49,6 +49,27 @@ static inline int hugepd_ok(hugepd_t hpd)
 }
 #define is_hugepd(hpd)		(hugepd_ok(hpd))
 
+/*
+ * 16M and 16G huge page directory tables are allocated from slab cache
+ *
+ */
+#define H_16M_CACHE_INDEX (PAGE_SHIFT + H_PTE_INDEX_SIZE + H_PMD_INDEX_SIZE - 24)
+#define H_16G_CACHE_INDEX                                                      \
+	(PAGE_SHIFT + H_PTE_INDEX_SIZE + H_PMD_INDEX_SIZE + H_PUD_INDEX_SIZE - 34)
+
+static inline int get_hugepd_cache_index(int index)
+{
+	switch (index) {
+	case H_16M_CACHE_INDEX:
+		return HTLB_16M_INDEX;
+	case H_16G_CACHE_INDEX:
+		return HTLB_16G_INDEX;
+	default:
+		BUG();
+	}
+	/* should not reach */
+}
+
 #else /* !CONFIG_HUGETLB_PAGE */
 static inline int pmd_huge(pmd_t pmd) { return 0; }
 static inline int pud_huge(pud_t pud) { return 0; }