hwmon: lochnagar: Add Lochnagar 2 hardware monitoring driver
Lochnagar is an evaluation and development board for Cirrus Logic Smart CODEC and Amp devices. It allows the connection of most Cirrus Logic devices on mini-cards, as well as allowing connection of various application processor systems to provide a full evaluation platform. This driver adds support for the hardware monitoring features of the Lochnagar 2 to the hwmon API. Monitoring is provided for the board voltages, currents and temperature supported by the board controller chip. Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net>hifive-unleashed-5.2
Lucas Tanure
Guenter Roeck
parent
5ad4d7ca21
commit
4cdb562147
|
|
@ -0,0 +1,80 @@
|
|||
Kernel Driver Lochnagar
|
||||
========================
|
||||
|
||||
Supported systems:
|
||||
* Cirrus Logic : Lochnagar 2
|
||||
|
||||
Author: Lucas A. Tanure Alves
|
||||
|
||||
Description
|
||||
-----------
|
||||
|
||||
Lochnagar 2 features built-in Current Monitor circuitry that allows for the
|
||||
measurement of both voltage and current on up to eight of the supply voltage
|
||||
rails provided to the minicards. The Current Monitor does not require any
|
||||
hardware modifications or external circuitry to operate.
|
||||
|
||||
The current and voltage measurements are obtained through the standard register
|
||||
map interface to the Lochnagar board controller, and can therefore be monitored
|
||||
by software.
|
||||
|
||||
Sysfs attributes
|
||||
----------------
|
||||
|
||||
temp1_input The Lochnagar board temperature (milliCelsius)
|
||||
in0_input Measured voltage for DBVDD1 (milliVolts)
|
||||
in0_label "DBVDD1"
|
||||
curr1_input Measured current for DBVDD1 (milliAmps)
|
||||
curr1_label "DBVDD1"
|
||||
power1_average Measured average power for DBVDD1 (microWatts)
|
||||
power1_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power1_label "DBVDD1"
|
||||
in1_input Measured voltage for 1V8 DSP (milliVolts)
|
||||
in1_label "1V8 DSP"
|
||||
curr2_input Measured current for 1V8 DSP (milliAmps)
|
||||
curr2_label "1V8 DSP"
|
||||
power2_average Measured average power for 1V8 DSP (microWatts)
|
||||
power2_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power2_label "1V8 DSP"
|
||||
in2_input Measured voltage for 1V8 CDC (milliVolts)
|
||||
in2_label "1V8 CDC"
|
||||
curr3_input Measured current for 1V8 CDC (milliAmps)
|
||||
curr3_label "1V8 CDC"
|
||||
power3_average Measured average power for 1V8 CDC (microWatts)
|
||||
power3_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power3_label "1V8 CDC"
|
||||
in3_input Measured voltage for VDDCORE DSP (milliVolts)
|
||||
in3_label "VDDCORE DSP"
|
||||
curr4_input Measured current for VDDCORE DSP (milliAmps)
|
||||
curr4_label "VDDCORE DSP"
|
||||
power4_average Measured average power for VDDCORE DSP (microWatts)
|
||||
power4_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power4_label "VDDCORE DSP"
|
||||
in4_input Measured voltage for AVDD 1V8 (milliVolts)
|
||||
in4_label "AVDD 1V8"
|
||||
curr5_input Measured current for AVDD 1V8 (milliAmps)
|
||||
curr5_label "AVDD 1V8"
|
||||
power5_average Measured average power for AVDD 1V8 (microWatts)
|
||||
power5_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power5_label "AVDD 1V8"
|
||||
curr6_input Measured current for SYSVDD (milliAmps)
|
||||
curr6_label "SYSVDD"
|
||||
power6_average Measured average power for SYSVDD (microWatts)
|
||||
power6_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power6_label "SYSVDD"
|
||||
in6_input Measured voltage for VDDCORE CDC (milliVolts)
|
||||
in6_label "VDDCORE CDC"
|
||||
curr7_input Measured current for VDDCORE CDC (milliAmps)
|
||||
curr7_label "VDDCORE CDC"
|
||||
power7_average Measured average power for VDDCORE CDC (microWatts)
|
||||
power7_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power7_label "VDDCORE CDC"
|
||||
in7_input Measured voltage for MICVDD (milliVolts)
|
||||
in7_label "MICVDD"
|
||||
curr8_input Measured current for MICVDD (milliAmps)
|
||||
curr8_label "MICVDD"
|
||||
power8_average Measured average power for MICVDD (microWatts)
|
||||
power8_average_interval Power averaging time input valid from 1 to 1708mS
|
||||
power8_label "MICVDD"
|
||||
|
||||
Note: It is not possible to measure voltage on the SYSVDD rail.
|
||||
|
|
@ -3797,6 +3797,7 @@ M: Richard Fitzgerald <rf@opensource.cirrus.com>
|
|||
L: patches@opensource.cirrus.com
|
||||
S: Supported
|
||||
F: drivers/clk/clk-lochnagar.c
|
||||
F: drivers/hwmon/lochnagar-hwmon.c
|
||||
F: drivers/mfd/lochnagar-i2c.c
|
||||
F: drivers/pinctrl/cirrus/pinctrl-lochnagar.c
|
||||
F: drivers/regulator/lochnagar-regulator.c
|
||||
|
|
@ -3805,8 +3806,10 @@ F: include/dt-bindings/pinctrl/lochnagar.h
|
|||
F: include/linux/mfd/lochnagar*
|
||||
F: Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt
|
||||
F: Documentation/devicetree/bindings/clock/cirrus,lochnagar.txt
|
||||
F: Documentation/devicetree/bindings/hwmon/cirrus,lochnagar.txt
|
||||
F: Documentation/devicetree/bindings/pinctrl/cirrus,lochnagar.txt
|
||||
F: Documentation/devicetree/bindings/regulator/cirrus,lochnagar.txt
|
||||
F: Documentation/hwmon/lochnagar
|
||||
|
||||
CISCO FCOE HBA DRIVER
|
||||
M: Satish Kharat <satishkh@cisco.com>
|
||||
|
|
|
|||
|
|
@ -705,6 +705,16 @@ config SENSORS_LINEAGE
|
|||
This driver can also be built as a module. If so, the module
|
||||
will be called lineage-pem.
|
||||
|
||||
config SENSORS_LOCHNAGAR
|
||||
tristate "Lochnagar Hardware Monitor"
|
||||
depends on MFD_LOCHNAGAR
|
||||
help
|
||||
If you say yes here you get support for Lochnagar 2 temperature,
|
||||
voltage and current sensors abilities.
|
||||
|
||||
This driver can also be built as a module. If so, the module
|
||||
will be called lochnagar-hwmon.
|
||||
|
||||
config SENSORS_LTC2945
|
||||
tristate "Linear Technology LTC2945"
|
||||
depends on I2C
|
||||
|
|
|
|||
|
|
@ -89,6 +89,7 @@ obj-$(CONFIG_SENSORS_JZ4740) += jz4740-hwmon.o
|
|||
obj-$(CONFIG_SENSORS_K8TEMP) += k8temp.o
|
||||
obj-$(CONFIG_SENSORS_K10TEMP) += k10temp.o
|
||||
obj-$(CONFIG_SENSORS_LINEAGE) += lineage-pem.o
|
||||
obj-$(CONFIG_SENSORS_LOCHNAGAR) += lochnagar-hwmon.o
|
||||
obj-$(CONFIG_SENSORS_LM63) += lm63.o
|
||||
obj-$(CONFIG_SENSORS_LM70) += lm70.o
|
||||
obj-$(CONFIG_SENSORS_LM73) += lm73.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,412 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
/*
|
||||
* Lochnagar hardware monitoring features
|
||||
*
|
||||
* Copyright (c) 2016-2019 Cirrus Logic, Inc. and
|
||||
* Cirrus Logic International Semiconductor Ltd.
|
||||
*
|
||||
* Author: Lucas Tanure <tanureal@opensource.cirrus.com>
|
||||
*/
|
||||
|
||||
#include <linux/delay.h>
|
||||
#include <linux/hwmon.h>
|
||||
#include <linux/hwmon-sysfs.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/math64.h>
|
||||
#include <linux/mfd/lochnagar.h>
|
||||
#include <linux/mfd/lochnagar2_regs.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_device.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/regmap.h>
|
||||
|
||||
#define LN2_MAX_NSAMPLE 1023
|
||||
#define LN2_SAMPLE_US 1670
|
||||
|
||||
#define LN2_CURR_UNITS 1000
|
||||
#define LN2_VOLT_UNITS 1000
|
||||
#define LN2_TEMP_UNITS 1000
|
||||
#define LN2_PWR_UNITS 1000000
|
||||
|
||||
static const char * const lochnagar_chan_names[] = {
|
||||
"DBVDD1",
|
||||
"1V8 DSP",
|
||||
"1V8 CDC",
|
||||
"VDDCORE DSP",
|
||||
"AVDD 1V8",
|
||||
"SYSVDD",
|
||||
"VDDCORE CDC",
|
||||
"MICVDD",
|
||||
};
|
||||
|
||||
struct lochnagar_hwmon {
|
||||
struct regmap *regmap;
|
||||
|
||||
long power_nsamples[ARRAY_SIZE(lochnagar_chan_names)];
|
||||
|
||||
/* Lock to ensure only a single sensor is read at a time */
|
||||
struct mutex sensor_lock;
|
||||
};
|
||||
|
||||
enum lochnagar_measure_mode {
|
||||
LN2_CURR = 0,
|
||||
LN2_VOLT,
|
||||
LN2_TEMP,
|
||||
};
|
||||
|
||||
/**
|
||||
* float_to_long - Convert ieee754 reading from hardware to an integer
|
||||
*
|
||||
* @data: Value read from the hardware
|
||||
* @precision: Units to multiply up to eg. 1000 = milli, 1000000 = micro
|
||||
*
|
||||
* Return: Converted integer reading
|
||||
*
|
||||
* Depending on the measurement type the hardware returns an ieee754
|
||||
* floating point value in either volts, amps or celsius. This function
|
||||
* will convert that into an integer in a smaller unit such as micro-amps
|
||||
* or milli-celsius. The hardware does not return NaN, so consideration of
|
||||
* that is not required.
|
||||
*/
|
||||
static long float_to_long(u32 data, u32 precision)
|
||||
{
|
||||
u64 man = data & 0x007FFFFF;
|
||||
int exp = ((data & 0x7F800000) >> 23) - 127 - 23;
|
||||
bool negative = data & 0x80000000;
|
||||
long result;
|
||||
|
||||
man = (man + (1 << 23)) * precision;
|
||||
|
||||
if (fls64(man) + exp > (int)sizeof(long) * 8 - 1)
|
||||
result = LONG_MAX;
|
||||
else if (exp < 0)
|
||||
result = (man + (1ull << (-exp - 1))) >> -exp;
|
||||
else
|
||||
result = man << exp;
|
||||
|
||||
return negative ? -result : result;
|
||||
}
|
||||
|
||||
static int do_measurement(struct regmap *regmap, int chan,
|
||||
enum lochnagar_measure_mode mode, int nsamples)
|
||||
{
|
||||
unsigned int val;
|
||||
int ret;
|
||||
|
||||
chan = 1 << (chan + LOCHNAGAR2_IMON_MEASURED_CHANNELS_SHIFT);
|
||||
|
||||
ret = regmap_write(regmap, LOCHNAGAR2_IMON_CTRL1,
|
||||
LOCHNAGAR2_IMON_ENA_MASK | chan | mode);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = regmap_write(regmap, LOCHNAGAR2_IMON_CTRL2, nsamples);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = regmap_write(regmap, LOCHNAGAR2_IMON_CTRL3,
|
||||
LOCHNAGAR2_IMON_CONFIGURE_MASK);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = regmap_read_poll_timeout(regmap, LOCHNAGAR2_IMON_CTRL3, val,
|
||||
val & LOCHNAGAR2_IMON_DONE_MASK,
|
||||
1000, 10000);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = regmap_write(regmap, LOCHNAGAR2_IMON_CTRL3,
|
||||
LOCHNAGAR2_IMON_MEASURE_MASK);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
/*
|
||||
* Actual measurement time is ~1.67mS per sample, approximate this
|
||||
* with a 1.5mS per sample msleep and then poll for success up to
|
||||
* ~0.17mS * 1023 (LN2_MAX_NSAMPLES). Normally for smaller values
|
||||
* of nsamples the poll will complete on the first loop due to
|
||||
* other latency in the system.
|
||||
*/
|
||||
msleep((nsamples * 3) / 2);
|
||||
|
||||
ret = regmap_read_poll_timeout(regmap, LOCHNAGAR2_IMON_CTRL3, val,
|
||||
val & LOCHNAGAR2_IMON_DONE_MASK,
|
||||
5000, 200000);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
return regmap_write(regmap, LOCHNAGAR2_IMON_CTRL3, 0);
|
||||
}
|
||||
|
||||
static int request_data(struct regmap *regmap, int chan, u32 *data)
|
||||
{
|
||||
unsigned int val;
|
||||
int ret;
|
||||
|
||||
ret = regmap_write(regmap, LOCHNAGAR2_IMON_CTRL4,
|
||||
LOCHNAGAR2_IMON_DATA_REQ_MASK |
|
||||
chan << LOCHNAGAR2_IMON_CH_SEL_SHIFT);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = regmap_read_poll_timeout(regmap, LOCHNAGAR2_IMON_CTRL4, val,
|
||||
val & LOCHNAGAR2_IMON_DATA_RDY_MASK,
|
||||
1000, 10000);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
ret = regmap_read(regmap, LOCHNAGAR2_IMON_DATA1, &val);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
*data = val << 16;
|
||||
|
||||
ret = regmap_read(regmap, LOCHNAGAR2_IMON_DATA2, &val);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
*data |= val;
|
||||
|
||||
return regmap_write(regmap, LOCHNAGAR2_IMON_CTRL4, 0);
|
||||
}
|
||||
|
||||
static int read_sensor(struct device *dev, int chan,
|
||||
enum lochnagar_measure_mode mode, int nsamples,
|
||||
unsigned int precision, long *val)
|
||||
{
|
||||
struct lochnagar_hwmon *priv = dev_get_drvdata(dev);
|
||||
struct regmap *regmap = priv->regmap;
|
||||
u32 data;
|
||||
int ret;
|
||||
|
||||
mutex_lock(&priv->sensor_lock);
|
||||
|
||||
ret = do_measurement(regmap, chan, mode, nsamples);
|
||||
if (ret < 0) {
|
||||
dev_err(dev, "Failed to perform measurement: %d\n", ret);
|
||||
goto error;
|
||||
}
|
||||
|
||||
ret = request_data(regmap, chan, &data);
|
||||
if (ret < 0) {
|
||||
dev_err(dev, "Failed to read measurement: %d\n", ret);
|
||||
goto error;
|
||||
}
|
||||
|
||||
*val = float_to_long(data, precision);
|
||||
|
||||
error:
|
||||
mutex_unlock(&priv->sensor_lock);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int read_power(struct device *dev, int chan, long *val)
|
||||
{
|
||||
struct lochnagar_hwmon *priv = dev_get_drvdata(dev);
|
||||
int nsamples = priv->power_nsamples[chan];
|
||||
u64 power;
|
||||
int ret;
|
||||
|
||||
if (!strcmp("SYSVDD", lochnagar_chan_names[chan])) {
|
||||
power = 5 * LN2_PWR_UNITS;
|
||||
} else {
|
||||
ret = read_sensor(dev, chan, LN2_VOLT, 1, LN2_PWR_UNITS, val);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
power = abs(*val);
|
||||
}
|
||||
|
||||
ret = read_sensor(dev, chan, LN2_CURR, nsamples, LN2_PWR_UNITS, val);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
power *= abs(*val);
|
||||
power = DIV_ROUND_CLOSEST_ULL(power, LN2_PWR_UNITS);
|
||||
|
||||
if (power > LONG_MAX)
|
||||
*val = LONG_MAX;
|
||||
else
|
||||
*val = power;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static umode_t lochnagar_is_visible(const void *drvdata,
|
||||
enum hwmon_sensor_types type,
|
||||
u32 attr, int chan)
|
||||
{
|
||||
switch (type) {
|
||||
case hwmon_in:
|
||||
if (!strcmp("SYSVDD", lochnagar_chan_names[chan]))
|
||||
return 0;
|
||||
break;
|
||||
case hwmon_power:
|
||||
if (attr == hwmon_power_average_interval)
|
||||
return 0644;
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
|
||||
return 0444;
|
||||
}
|
||||
|
||||
static int lochnagar_read(struct device *dev, enum hwmon_sensor_types type,
|
||||
u32 attr, int chan, long *val)
|
||||
{
|
||||
struct lochnagar_hwmon *priv = dev_get_drvdata(dev);
|
||||
int interval;
|
||||
|
||||
switch (type) {
|
||||
case hwmon_in:
|
||||
return read_sensor(dev, chan, LN2_VOLT, 1, LN2_VOLT_UNITS, val);
|
||||
case hwmon_curr:
|
||||
return read_sensor(dev, chan, LN2_CURR, 1, LN2_CURR_UNITS, val);
|
||||
case hwmon_temp:
|
||||
return read_sensor(dev, chan, LN2_TEMP, 1, LN2_TEMP_UNITS, val);
|
||||
case hwmon_power:
|
||||
switch (attr) {
|
||||
case hwmon_power_average:
|
||||
return read_power(dev, chan, val);
|
||||
case hwmon_power_average_interval:
|
||||
interval = priv->power_nsamples[chan] * LN2_SAMPLE_US;
|
||||
*val = DIV_ROUND_CLOSEST(interval, 1000);
|
||||
return 0;
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
}
|
||||
|
||||
static int lochnagar_read_string(struct device *dev,
|
||||
enum hwmon_sensor_types type, u32 attr,
|
||||
int chan, const char **str)
|
||||
{
|
||||
switch (type) {
|
||||
case hwmon_in:
|
||||
case hwmon_curr:
|
||||
case hwmon_power:
|
||||
*str = lochnagar_chan_names[chan];
|
||||
return 0;
|
||||
default:
|
||||
return -EOPNOTSUPP;
|
||||
}
|
||||
}
|
||||
|
||||
static int lochnagar_write(struct device *dev, enum hwmon_sensor_types type,
|
||||
u32 attr, int chan, long val)
|
||||
{
|
||||
struct lochnagar_hwmon *priv = dev_get_drvdata(dev);
|
||||
|
||||
if (type != hwmon_power || attr != hwmon_power_average_interval)
|
||||
return -EOPNOTSUPP;
|
||||
|
||||
val = clamp_t(long, val, 1, (LN2_MAX_NSAMPLE * LN2_SAMPLE_US) / 1000);
|
||||
val = DIV_ROUND_CLOSEST(val * 1000, LN2_SAMPLE_US);
|
||||
|
||||
priv->power_nsamples[chan] = val;
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct hwmon_ops lochnagar_ops = {
|
||||
.is_visible = lochnagar_is_visible,
|
||||
.read = lochnagar_read,
|
||||
.read_string = lochnagar_read_string,
|
||||
.write = lochnagar_write,
|
||||
};
|
||||
|
||||
static const struct hwmon_channel_info *lochnagar_info[] = {
|
||||
HWMON_CHANNEL_INFO(temp, HWMON_T_INPUT),
|
||||
HWMON_CHANNEL_INFO(in, HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL,
|
||||
HWMON_I_INPUT | HWMON_I_LABEL),
|
||||
HWMON_CHANNEL_INFO(curr, HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL,
|
||||
HWMON_C_INPUT | HWMON_C_LABEL),
|
||||
HWMON_CHANNEL_INFO(power, HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL,
|
||||
HWMON_P_AVERAGE | HWMON_P_AVERAGE_INTERVAL |
|
||||
HWMON_P_LABEL),
|
||||
NULL
|
||||
};
|
||||
|
||||
static const struct hwmon_chip_info lochnagar_chip_info = {
|
||||
.ops = &lochnagar_ops,
|
||||
.info = lochnagar_info,
|
||||
};
|
||||
|
||||
static const struct of_device_id lochnagar_of_match[] = {
|
||||
{ .compatible = "cirrus,lochnagar2-hwmon" },
|
||||
{}
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, lochnagar_of_match);
|
||||
|
||||
static int lochnagar_hwmon_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct device *dev = &pdev->dev;
|
||||
struct device *hwmon_dev;
|
||||
struct lochnagar_hwmon *priv;
|
||||
int i;
|
||||
|
||||
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
||||
if (!priv)
|
||||
return -ENOMEM;
|
||||
|
||||
mutex_init(&priv->sensor_lock);
|
||||
|
||||
priv->regmap = dev_get_regmap(dev->parent, NULL);
|
||||
if (!priv->regmap) {
|
||||
dev_err(dev, "No register map found\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
for (i = 0; i < ARRAY_SIZE(priv->power_nsamples); i++)
|
||||
priv->power_nsamples[i] = 96;
|
||||
|
||||
hwmon_dev = devm_hwmon_device_register_with_info(dev, "Lochnagar", priv,
|
||||
&lochnagar_chip_info,
|
||||
NULL);
|
||||
|
||||
return PTR_ERR_OR_ZERO(hwmon_dev);
|
||||
}
|
||||
|
||||
static struct platform_driver lochnagar_hwmon_driver = {
|
||||
.driver = {
|
||||
.name = "lochnagar-hwmon",
|
||||
.of_match_table = lochnagar_of_match,
|
||||
},
|
||||
.probe = lochnagar_hwmon_probe,
|
||||
};
|
||||
module_platform_driver(lochnagar_hwmon_driver);
|
||||
|
||||
MODULE_AUTHOR("Lucas Tanure <tanureal@opensource.cirrus.com>");
|
||||
MODULE_DESCRIPTION("Lochnagar hardware monitoring features");
|
||||
MODULE_LICENSE("GPL");
|
||||
Loading…
Reference in New Issue