xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen implementation, including: - booting and setup - pagetable setup - privileged instructions - segmentation - interrupt flags - upcalls - multicall batching BOOTING AND SETUP The vmlinux image is decorated with ELF notes which tell the Xen domain builder what the kernel's requirements are; the domain builder then constructs the address space accordingly and starts the kernel. Xen has its own entrypoint for the kernel (contained in an ELF note). The ELF notes are set up by xen-head.S, which is included into head.S. In principle it could be linked separately, but it seems to provoke lots of binutils bugs. Because the domain builder starts the kernel in a fairly sane state (32-bit protected mode, paging enabled, flat segments set up), there's not a lot of setup needed before starting the kernel proper. The main steps are: 1. Install the Xen paravirt_ops, which is simply a matter of a structure assignment. 2. Set init_mm to use the Xen-supplied pagetables (analogous to the head.S generated pagetables in a native boot). 3. Reserve address space for Xen, since it takes a chunk at the top of the address space for its own use. 4. Call start_kernel() PAGETABLE SETUP Once we hit the main kernel boot sequence, it will end up calling back via paravirt_ops to set up various pieces of Xen specific state. One of the critical things which requires a bit of extra care is the construction of the initial init_mm pagetable. Because Xen places tight constraints on pagetables (an active pagetable must always be valid, and must always be mapped read-only to the guest domain), we need to be careful when constructing the new pagetable to keep these constraints in mind. It turns out that the easiest way to do this is use the initial Xen-provided pagetable as a template, and then just insert new mappings for memory where a mapping doesn't already exist. This means that during pagetable setup, it uses a special version of xen_set_pte which ignores any attempt to remap a read-only page as read-write (since Xen will map its own initial pagetable as RO), but lets other changes to the ptes happen, so that things like NX are set properly. PRIVILEGED INSTRUCTIONS AND SEGMENTATION When the kernel runs under Xen, it runs in ring 1 rather than ring 0. This means that it is more privileged than user-mode in ring 3, but it still can't run privileged instructions directly. Non-performance critical instructions are dealt with by taking a privilege exception and trapping into the hypervisor and emulating the instruction, but more performance-critical instructions have their own specific paravirt_ops. In many cases we can avoid having to do any hypercalls for these instructions, or the Xen implementation is quite different from the normal native version. The privileged instructions fall into the broad classes of: Segmentation: setting up the GDT and the GDT entries, LDT, TLS and so on. Xen doesn't allow the GDT to be directly modified; all GDT updates are done via hypercalls where the new entries can be validated. This is important because Xen uses segment limits to prevent the guest kernel from damaging the hypervisor itself. Traps and exceptions: Xen uses a special format for trap entrypoints, so when the kernel wants to set an IDT entry, it needs to be converted to the form Xen expects. Xen sets int 0x80 up specially so that the trap goes straight from userspace into the guest kernel without going via the hypervisor. sysenter isn't supported. Kernel stack: The esp0 entry is extracted from the tss and provided to Xen. TLB operations: the various TLB calls are mapped into corresponding Xen hypercalls. Control registers: all the control registers are privileged. The most important is cr3, which points to the base of the current pagetable, and we handle it specially. Another instruction we treat specially is CPUID, even though its not privileged. We want to control what CPU features are visible to the rest of the kernel, and so CPUID ends up going into a paravirt_op. Xen implements this mainly to disable the ACPI and APIC subsystems. INTERRUPT FLAGS Xen maintains its own separate flag for masking events, which is contained within the per-cpu vcpu_info structure. Because the guest kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely ignored (and must be, because even if a guest domain disables interrupts for itself, it can't disable them overall). (A note on terminology: "events" and interrupts are effectively synonymous. However, rather than using an "enable flag", Xen uses a "mask flag", which blocks event delivery when it is non-zero.) There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which are implemented to manage the Xen event mask state. The only thing worth noting is that when events are unmasked, we need to explicitly see if there's a pending event and call into the hypervisor to make sure it gets delivered. UPCALLS Xen needs a couple of upcall (or callback) functions to be implemented by each guest. One is the event upcalls, which is how events (interrupts, effectively) are delivered to the guests. The other is the failsafe callback, which is used to report errors in either reloading a segment register, or caused by iret. These are implemented in i386/kernel/entry.S so they can jump into the normal iret_exc path when necessary. MULTICALL BATCHING Xen provides a multicall mechanism, which allows multiple hypercalls to be issued at once in order to mitigate the cost of trapping into the hypervisor. This is particularly useful for context switches, since the 4-5 hypercalls they would normally need (reload cr3, update TLS, maybe update LDT) can be reduced to one. This patch implements a generic batching mechanism for hypercalls, which gets used in many places in the Xen code. Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Signed-off-by: Chris Wright <chrisw@sous-sol.org> Cc: Ian Pratt <ian.pratt@xensource.com> Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk> Cc: Adrian Bunk <bunk@stusta.de>
This commit is contained in:
parent
a42089dd35
commit
5ead97c84f
|
@ -93,6 +93,9 @@ mflags-$(CONFIG_X86_ES7000) := -Iinclude/asm-i386/mach-es7000
|
|||
mcore-$(CONFIG_X86_ES7000) := mach-default
|
||||
core-$(CONFIG_X86_ES7000) := arch/i386/mach-es7000/
|
||||
|
||||
# Xen paravirtualization support
|
||||
core-$(CONFIG_XEN) += arch/i386/xen/
|
||||
|
||||
# default subarch .h files
|
||||
mflags-y += -Iinclude/asm-i386/mach-default
|
||||
|
||||
|
|
|
@ -1023,6 +1023,77 @@ ENTRY(kernel_thread_helper)
|
|||
CFI_ENDPROC
|
||||
ENDPROC(kernel_thread_helper)
|
||||
|
||||
#ifdef CONFIG_XEN
|
||||
ENTRY(xen_hypervisor_callback)
|
||||
CFI_STARTPROC
|
||||
pushl $0
|
||||
CFI_ADJUST_CFA_OFFSET 4
|
||||
SAVE_ALL
|
||||
TRACE_IRQS_OFF
|
||||
mov %esp, %eax
|
||||
call xen_evtchn_do_upcall
|
||||
jmp ret_from_intr
|
||||
CFI_ENDPROC
|
||||
ENDPROC(xen_hypervisor_callback)
|
||||
|
||||
# Hypervisor uses this for application faults while it executes.
|
||||
# We get here for two reasons:
|
||||
# 1. Fault while reloading DS, ES, FS or GS
|
||||
# 2. Fault while executing IRET
|
||||
# Category 1 we fix up by reattempting the load, and zeroing the segment
|
||||
# register if the load fails.
|
||||
# Category 2 we fix up by jumping to do_iret_error. We cannot use the
|
||||
# normal Linux return path in this case because if we use the IRET hypercall
|
||||
# to pop the stack frame we end up in an infinite loop of failsafe callbacks.
|
||||
# We distinguish between categories by maintaining a status value in EAX.
|
||||
ENTRY(xen_failsafe_callback)
|
||||
CFI_STARTPROC
|
||||
pushl %eax
|
||||
CFI_ADJUST_CFA_OFFSET 4
|
||||
movl $1,%eax
|
||||
1: mov 4(%esp),%ds
|
||||
2: mov 8(%esp),%es
|
||||
3: mov 12(%esp),%fs
|
||||
4: mov 16(%esp),%gs
|
||||
testl %eax,%eax
|
||||
popl %eax
|
||||
CFI_ADJUST_CFA_OFFSET -4
|
||||
lea 16(%esp),%esp
|
||||
CFI_ADJUST_CFA_OFFSET -16
|
||||
jz 5f
|
||||
addl $16,%esp
|
||||
jmp iret_exc # EAX != 0 => Category 2 (Bad IRET)
|
||||
5: pushl $0 # EAX == 0 => Category 1 (Bad segment)
|
||||
CFI_ADJUST_CFA_OFFSET 4
|
||||
SAVE_ALL
|
||||
jmp ret_from_exception
|
||||
CFI_ENDPROC
|
||||
|
||||
.section .fixup,"ax"
|
||||
6: xorl %eax,%eax
|
||||
movl %eax,4(%esp)
|
||||
jmp 1b
|
||||
7: xorl %eax,%eax
|
||||
movl %eax,8(%esp)
|
||||
jmp 2b
|
||||
8: xorl %eax,%eax
|
||||
movl %eax,12(%esp)
|
||||
jmp 3b
|
||||
9: xorl %eax,%eax
|
||||
movl %eax,16(%esp)
|
||||
jmp 4b
|
||||
.previous
|
||||
.section __ex_table,"a"
|
||||
.align 4
|
||||
.long 1b,6b
|
||||
.long 2b,7b
|
||||
.long 3b,8b
|
||||
.long 4b,9b
|
||||
.previous
|
||||
ENDPROC(xen_failsafe_callback)
|
||||
|
||||
#endif /* CONFIG_XEN */
|
||||
|
||||
.section .rodata,"a"
|
||||
#include "syscall_table.S"
|
||||
|
||||
|
|
|
@ -510,7 +510,8 @@ ENTRY(_stext)
|
|||
/*
|
||||
* BSS section
|
||||
*/
|
||||
.section ".bss.page_aligned","w"
|
||||
.section ".bss.page_aligned","wa"
|
||||
.align PAGE_SIZE_asm
|
||||
ENTRY(swapper_pg_dir)
|
||||
.fill 1024,4,0
|
||||
ENTRY(swapper_pg_pmd)
|
||||
|
@ -538,6 +539,8 @@ fault_msg:
|
|||
.ascii "Int %d: CR2 %p err %p EIP %p CS %p flags %p\n"
|
||||
.asciz "Stack: %p %p %p %p %p %p %p %p\n"
|
||||
|
||||
#include "../xen/xen-head.S"
|
||||
|
||||
/*
|
||||
* The IDT and GDT 'descriptors' are a strange 48-bit object
|
||||
* only used by the lidt and lgdt instructions. They are not
|
||||
|
|
|
@ -88,6 +88,7 @@ SECTIONS
|
|||
|
||||
. = ALIGN(4096);
|
||||
.data.page_aligned : AT(ADDR(.data.page_aligned) - LOAD_OFFSET) {
|
||||
*(.data.page_aligned)
|
||||
*(.data.idt)
|
||||
}
|
||||
|
||||
|
|
1
arch/i386/xen/Makefile
Normal file
1
arch/i386/xen/Makefile
Normal file
|
@ -0,0 +1 @@
|
|||
obj-y := enlighten.o setup.o features.o multicalls.o
|
745
arch/i386/xen/enlighten.c
Normal file
745
arch/i386/xen/enlighten.c
Normal file
|
@ -0,0 +1,745 @@
|
|||
/*
|
||||
* Core of Xen paravirt_ops implementation.
|
||||
*
|
||||
* This file contains the xen_paravirt_ops structure itself, and the
|
||||
* implementations for:
|
||||
* - privileged instructions
|
||||
* - interrupt flags
|
||||
* - segment operations
|
||||
* - booting and setup
|
||||
*
|
||||
* Jeremy Fitzhardinge <jeremy@xensource.com>, XenSource Inc, 2007
|
||||
*/
|
||||
|
||||
#include <linux/kernel.h>
|
||||
#include <linux/init.h>
|
||||
#include <linux/smp.h>
|
||||
#include <linux/preempt.h>
|
||||
#include <linux/percpu.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/start_kernel.h>
|
||||
#include <linux/sched.h>
|
||||
#include <linux/bootmem.h>
|
||||
#include <linux/module.h>
|
||||
|
||||
#include <xen/interface/xen.h>
|
||||
#include <xen/interface/physdev.h>
|
||||
#include <xen/interface/vcpu.h>
|
||||
#include <xen/features.h>
|
||||
#include <xen/page.h>
|
||||
|
||||
#include <asm/paravirt.h>
|
||||
#include <asm/page.h>
|
||||
#include <asm/xen/hypercall.h>
|
||||
#include <asm/xen/hypervisor.h>
|
||||
#include <asm/fixmap.h>
|
||||
#include <asm/processor.h>
|
||||
#include <asm/setup.h>
|
||||
#include <asm/desc.h>
|
||||
#include <asm/pgtable.h>
|
||||
|
||||
#include "xen-ops.h"
|
||||
#include "multicalls.h"
|
||||
|
||||
EXPORT_SYMBOL_GPL(hypercall_page);
|
||||
|
||||
DEFINE_PER_CPU(enum paravirt_lazy_mode, xen_lazy_mode);
|
||||
|
||||
DEFINE_PER_CPU(struct vcpu_info *, xen_vcpu);
|
||||
DEFINE_PER_CPU(struct vcpu_info, xen_vcpu_info);
|
||||
DEFINE_PER_CPU(unsigned long, xen_cr3);
|
||||
|
||||
struct start_info *xen_start_info;
|
||||
EXPORT_SYMBOL_GPL(xen_start_info);
|
||||
|
||||
static void xen_vcpu_setup(int cpu)
|
||||
{
|
||||
per_cpu(xen_vcpu, cpu) = &HYPERVISOR_shared_info->vcpu_info[cpu];
|
||||
}
|
||||
|
||||
static void __init xen_banner(void)
|
||||
{
|
||||
printk(KERN_INFO "Booting paravirtualized kernel on %s\n",
|
||||
paravirt_ops.name);
|
||||
printk(KERN_INFO "Hypervisor signature: %s\n", xen_start_info->magic);
|
||||
}
|
||||
|
||||
static void xen_cpuid(unsigned int *eax, unsigned int *ebx,
|
||||
unsigned int *ecx, unsigned int *edx)
|
||||
{
|
||||
unsigned maskedx = ~0;
|
||||
|
||||
/*
|
||||
* Mask out inconvenient features, to try and disable as many
|
||||
* unsupported kernel subsystems as possible.
|
||||
*/
|
||||
if (*eax == 1)
|
||||
maskedx = ~((1 << X86_FEATURE_APIC) | /* disable APIC */
|
||||
(1 << X86_FEATURE_ACPI) | /* disable ACPI */
|
||||
(1 << X86_FEATURE_ACC)); /* thermal monitoring */
|
||||
|
||||
asm(XEN_EMULATE_PREFIX "cpuid"
|
||||
: "=a" (*eax),
|
||||
"=b" (*ebx),
|
||||
"=c" (*ecx),
|
||||
"=d" (*edx)
|
||||
: "0" (*eax), "2" (*ecx));
|
||||
*edx &= maskedx;
|
||||
}
|
||||
|
||||
static void xen_set_debugreg(int reg, unsigned long val)
|
||||
{
|
||||
HYPERVISOR_set_debugreg(reg, val);
|
||||
}
|
||||
|
||||
static unsigned long xen_get_debugreg(int reg)
|
||||
{
|
||||
return HYPERVISOR_get_debugreg(reg);
|
||||
}
|
||||
|
||||
static unsigned long xen_save_fl(void)
|
||||
{
|
||||
struct vcpu_info *vcpu;
|
||||
unsigned long flags;
|
||||
|
||||
preempt_disable();
|
||||
vcpu = x86_read_percpu(xen_vcpu);
|
||||
/* flag has opposite sense of mask */
|
||||
flags = !vcpu->evtchn_upcall_mask;
|
||||
preempt_enable();
|
||||
|
||||
/* convert to IF type flag
|
||||
-0 -> 0x00000000
|
||||
-1 -> 0xffffffff
|
||||
*/
|
||||
return (-flags) & X86_EFLAGS_IF;
|
||||
}
|
||||
|
||||
static void xen_restore_fl(unsigned long flags)
|
||||
{
|
||||
struct vcpu_info *vcpu;
|
||||
|
||||
preempt_disable();
|
||||
|
||||
/* convert from IF type flag */
|
||||
flags = !(flags & X86_EFLAGS_IF);
|
||||
vcpu = x86_read_percpu(xen_vcpu);
|
||||
vcpu->evtchn_upcall_mask = flags;
|
||||
|
||||
if (flags == 0) {
|
||||
/* Unmask then check (avoid races). We're only protecting
|
||||
against updates by this CPU, so there's no need for
|
||||
anything stronger. */
|
||||
barrier();
|
||||
|
||||
if (unlikely(vcpu->evtchn_upcall_pending))
|
||||
force_evtchn_callback();
|
||||
preempt_enable();
|
||||
} else
|
||||
preempt_enable_no_resched();
|
||||
}
|
||||
|
||||
static void xen_irq_disable(void)
|
||||
{
|
||||
struct vcpu_info *vcpu;
|
||||
preempt_disable();
|
||||
vcpu = x86_read_percpu(xen_vcpu);
|
||||
vcpu->evtchn_upcall_mask = 1;
|
||||
preempt_enable_no_resched();
|
||||
}
|
||||
|
||||
static void xen_irq_enable(void)
|
||||
{
|
||||
struct vcpu_info *vcpu;
|
||||
|
||||
preempt_disable();
|
||||
vcpu = x86_read_percpu(xen_vcpu);
|
||||
vcpu->evtchn_upcall_mask = 0;
|
||||
|
||||
/* Unmask then check (avoid races). We're only protecting
|
||||
against updates by this CPU, so there's no need for
|
||||
anything stronger. */
|
||||
barrier();
|
||||
|
||||
if (unlikely(vcpu->evtchn_upcall_pending))
|
||||
force_evtchn_callback();
|
||||
preempt_enable();
|
||||
}
|
||||
|
||||
static void xen_safe_halt(void)
|
||||
{
|
||||
/* Blocking includes an implicit local_irq_enable(). */
|
||||
if (HYPERVISOR_sched_op(SCHEDOP_block, 0) != 0)
|
||||
BUG();
|
||||
}
|
||||
|
||||
static void xen_halt(void)
|
||||
{
|
||||
if (irqs_disabled())
|
||||
HYPERVISOR_vcpu_op(VCPUOP_down, smp_processor_id(), NULL);
|
||||
else
|
||||
xen_safe_halt();
|
||||
}
|
||||
|
||||
static void xen_set_lazy_mode(enum paravirt_lazy_mode mode)
|
||||
{
|
||||
switch (mode) {
|
||||
case PARAVIRT_LAZY_NONE:
|
||||
BUG_ON(x86_read_percpu(xen_lazy_mode) == PARAVIRT_LAZY_NONE);
|
||||
break;
|
||||
|
||||
case PARAVIRT_LAZY_MMU:
|
||||
case PARAVIRT_LAZY_CPU:
|
||||
BUG_ON(x86_read_percpu(xen_lazy_mode) != PARAVIRT_LAZY_NONE);
|
||||
break;
|
||||
|
||||
case PARAVIRT_LAZY_FLUSH:
|
||||
/* flush if necessary, but don't change state */
|
||||
if (x86_read_percpu(xen_lazy_mode) != PARAVIRT_LAZY_NONE)
|
||||
xen_mc_flush();
|
||||
return;
|
||||
}
|
||||
|
||||
xen_mc_flush();
|
||||
x86_write_percpu(xen_lazy_mode, mode);
|
||||
}
|
||||
|
||||
static unsigned long xen_store_tr(void)
|
||||
{
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void xen_set_ldt(const void *addr, unsigned entries)
|
||||
{
|
||||
unsigned long linear_addr = (unsigned long)addr;
|
||||
struct mmuext_op *op;
|
||||
struct multicall_space mcs = xen_mc_entry(sizeof(*op));
|
||||
|
||||
op = mcs.args;
|
||||
op->cmd = MMUEXT_SET_LDT;
|
||||
if (linear_addr) {
|
||||
/* ldt my be vmalloced, use arbitrary_virt_to_machine */
|
||||
xmaddr_t maddr;
|
||||
maddr = arbitrary_virt_to_machine((unsigned long)addr);
|
||||
linear_addr = (unsigned long)maddr.maddr;
|
||||
}
|
||||
op->arg1.linear_addr = linear_addr;
|
||||
op->arg2.nr_ents = entries;
|
||||
|
||||
MULTI_mmuext_op(mcs.mc, op, 1, NULL, DOMID_SELF);
|
||||
|
||||
xen_mc_issue(PARAVIRT_LAZY_CPU);
|
||||
}
|
||||
|
||||
static void xen_load_gdt(const struct Xgt_desc_struct *dtr)
|
||||
{
|
||||
unsigned long *frames;
|
||||
unsigned long va = dtr->address;
|
||||
unsigned int size = dtr->size + 1;
|
||||
unsigned pages = (size + PAGE_SIZE - 1) / PAGE_SIZE;
|
||||
int f;
|
||||
struct multicall_space mcs;
|
||||
|
||||
/* A GDT can be up to 64k in size, which corresponds to 8192
|
||||
8-byte entries, or 16 4k pages.. */
|
||||
|
||||
BUG_ON(size > 65536);
|
||||
BUG_ON(va & ~PAGE_MASK);
|
||||
|
||||
mcs = xen_mc_entry(sizeof(*frames) * pages);
|
||||
frames = mcs.args;
|
||||
|
||||
for (f = 0; va < dtr->address + size; va += PAGE_SIZE, f++) {
|
||||
frames[f] = virt_to_mfn(va);
|
||||
make_lowmem_page_readonly((void *)va);
|
||||
}
|
||||
|
||||
MULTI_set_gdt(mcs.mc, frames, size / sizeof(struct desc_struct));
|
||||
|
||||
xen_mc_issue(PARAVIRT_LAZY_CPU);
|
||||
}
|
||||
|
||||
static void load_TLS_descriptor(struct thread_struct *t,
|
||||
unsigned int cpu, unsigned int i)
|
||||
{
|
||||
struct desc_struct *gdt = get_cpu_gdt_table(cpu);
|
||||
xmaddr_t maddr = virt_to_machine(&gdt[GDT_ENTRY_TLS_MIN+i]);
|
||||
struct multicall_space mc = __xen_mc_entry(0);
|
||||
|
||||
MULTI_update_descriptor(mc.mc, maddr.maddr, t->tls_array[i]);
|
||||
}
|
||||
|
||||
static void xen_load_tls(struct thread_struct *t, unsigned int cpu)
|
||||
{
|
||||
xen_mc_batch();
|
||||
|
||||
load_TLS_descriptor(t, cpu, 0);
|
||||
load_TLS_descriptor(t, cpu, 1);
|
||||
load_TLS_descriptor(t, cpu, 2);
|
||||
|
||||
xen_mc_issue(PARAVIRT_LAZY_CPU);
|
||||
}
|
||||
|
||||
static void xen_write_ldt_entry(struct desc_struct *dt, int entrynum,
|
||||
u32 low, u32 high)
|
||||
{
|
||||
unsigned long lp = (unsigned long)&dt[entrynum];
|
||||
xmaddr_t mach_lp = virt_to_machine(lp);
|
||||
u64 entry = (u64)high << 32 | low;
|
||||
|
||||
xen_mc_flush();
|
||||
if (HYPERVISOR_update_descriptor(mach_lp.maddr, entry))
|
||||
BUG();
|
||||
}
|
||||
|
||||
static int cvt_gate_to_trap(int vector, u32 low, u32 high,
|
||||
struct trap_info *info)
|
||||
{
|
||||
u8 type, dpl;
|
||||
|
||||
type = (high >> 8) & 0x1f;
|
||||
dpl = (high >> 13) & 3;
|
||||
|
||||
if (type != 0xf && type != 0xe)
|
||||
return 0;
|
||||
|
||||
info->vector = vector;
|
||||
info->address = (high & 0xffff0000) | (low & 0x0000ffff);
|
||||
info->cs = low >> 16;
|
||||
info->flags = dpl;
|
||||
/* interrupt gates clear IF */
|
||||
if (type == 0xe)
|
||||
info->flags |= 4;
|
||||
|
||||
return 1;
|
||||
}
|
||||
|
||||
/* Locations of each CPU's IDT */
|
||||
static DEFINE_PER_CPU(struct Xgt_desc_struct, idt_desc);
|
||||
|
||||
/* Set an IDT entry. If the entry is part of the current IDT, then
|
||||
also update Xen. */
|
||||
static void xen_write_idt_entry(struct desc_struct *dt, int entrynum,
|
||||
u32 low, u32 high)
|
||||
{
|
||||
|
||||
int cpu = smp_processor_id();
|
||||
unsigned long p = (unsigned long)&dt[entrynum];
|
||||
unsigned long start = per_cpu(idt_desc, cpu).address;
|
||||
unsigned long end = start + per_cpu(idt_desc, cpu).size + 1;
|
||||
|
||||
xen_mc_flush();
|
||||
|
||||
write_dt_entry(dt, entrynum, low, high);
|
||||
|
||||
if (p >= start && (p + 8) <= end) {
|
||||
struct trap_info info[2];
|
||||
|
||||
info[1].address = 0;
|
||||
|
||||
if (cvt_gate_to_trap(entrynum, low, high, &info[0]))
|
||||
if (HYPERVISOR_set_trap_table(info))
|
||||
BUG();
|
||||
}
|
||||
}
|
||||
|
||||
/* Load a new IDT into Xen. In principle this can be per-CPU, so we
|
||||
hold a spinlock to protect the static traps[] array (static because
|
||||
it avoids allocation, and saves stack space). */
|
||||
static void xen_load_idt(const struct Xgt_desc_struct *desc)
|
||||
{
|
||||
static DEFINE_SPINLOCK(lock);
|
||||
static struct trap_info traps[257];
|
||||
|
||||
int cpu = smp_processor_id();
|
||||
unsigned in, out, count;
|
||||
|
||||
per_cpu(idt_desc, cpu) = *desc;
|
||||
|
||||
count = (desc->size+1) / 8;
|
||||
BUG_ON(count > 256);
|
||||
|
||||
spin_lock(&lock);
|
||||
for (in = out = 0; in < count; in++) {
|
||||
const u32 *entry = (u32 *)(desc->address + in * 8);
|
||||
|
||||
if (cvt_gate_to_trap(in, entry[0], entry[1], &traps[out]))
|
||||
out++;
|
||||
}
|
||||
traps[out].address = 0;
|
||||
|
||||
xen_mc_flush();
|
||||
if (HYPERVISOR_set_trap_table(traps))
|
||||
BUG();
|
||||
|
||||
spin_unlock(&lock);
|
||||
}
|
||||
|
||||
/* Write a GDT descriptor entry. Ignore LDT descriptors, since
|
||||
they're handled differently. */
|
||||
static void xen_write_gdt_entry(struct desc_struct *dt, int entry,
|
||||
u32 low, u32 high)
|
||||
{
|
||||
switch ((high >> 8) & 0xff) {
|
||||
case DESCTYPE_LDT:
|
||||
case DESCTYPE_TSS:
|
||||
/* ignore */
|
||||
break;
|
||||
|
||||
default: {
|
||||
xmaddr_t maddr = virt_to_machine(&dt[entry]);
|
||||
u64 desc = (u64)high << 32 | low;
|
||||
|
||||
xen_mc_flush();
|
||||
if (HYPERVISOR_update_descriptor(maddr.maddr, desc))
|
||||
BUG();
|
||||
}
|
||||
|
||||
}
|
||||
}
|
||||
|
||||
static void xen_load_esp0(struct tss_struct *tss,
|
||||
struct thread_struct *thread)
|
||||
{
|
||||
struct multicall_space mcs = xen_mc_entry(0);
|
||||
MULTI_stack_switch(mcs.mc, __KERNEL_DS, thread->esp0);
|
||||
xen_mc_issue(PARAVIRT_LAZY_CPU);
|
||||
}
|
||||
|
||||
static void xen_set_iopl_mask(unsigned mask)
|
||||
{
|
||||
struct physdev_set_iopl set_iopl;
|
||||
|
||||
/* Force the change at ring 0. */
|
||||
set_iopl.iopl = (mask == 0) ? 1 : (mask >> 12) & 3;
|
||||
HYPERVISOR_physdev_op(PHYSDEVOP_set_iopl, &set_iopl);
|
||||
}
|
||||
|
||||
static void xen_io_delay(void)
|
||||
{
|
||||
}
|
||||
|
||||
#ifdef CONFIG_X86_LOCAL_APIC
|
||||
static unsigned long xen_apic_read(unsigned long reg)
|
||||
{
|
||||
return 0;
|
||||
}
|
||||
#endif
|
||||
|
||||
static void xen_flush_tlb(void)
|
||||
{
|
||||
struct mmuext_op op;
|
||||
|
||||
op.cmd = MMUEXT_TLB_FLUSH_LOCAL;
|
||||
if (HYPERVISOR_mmuext_op(&op, 1, NULL, DOMID_SELF))
|
||||
BUG();
|
||||
}
|
||||
|
||||
static void xen_flush_tlb_single(unsigned long addr)
|
||||
{
|
||||
struct mmuext_op op;
|
||||
|
||||
op.cmd = MMUEXT_INVLPG_LOCAL;
|
||||
op.arg1.linear_addr = addr & PAGE_MASK;
|
||||
if (HYPERVISOR_mmuext_op(&op, 1, NULL, DOMID_SELF))
|
||||
BUG();
|
||||
}
|
||||
|
||||
static unsigned long xen_read_cr2(void)
|
||||
{
|
||||
return x86_read_percpu(xen_vcpu)->arch.cr2;
|
||||
}
|
||||
|
||||
static void xen_write_cr4(unsigned long cr4)
|
||||
{
|
||||
/* never allow TSC to be disabled */
|
||||
native_write_cr4(cr4 & ~X86_CR4_TSD);
|
||||
}
|
||||
|
||||
/*
|
||||
* Page-directory addresses above 4GB do not fit into architectural %cr3.
|
||||
* When accessing %cr3, or equivalent field in vcpu_guest_context, guests
|
||||
* must use the following accessor macros to pack/unpack valid MFNs.
|
||||
*
|
||||
* Note that Xen is using the fact that the pagetable base is always
|
||||
* page-aligned, and putting the 12 MSB of the address into the 12 LSB
|
||||
* of cr3.
|
||||
*/
|
||||
#define xen_pfn_to_cr3(pfn) (((unsigned)(pfn) << 12) | ((unsigned)(pfn) >> 20))
|
||||
#define xen_cr3_to_pfn(cr3) (((unsigned)(cr3) >> 12) | ((unsigned)(cr3) << 20))
|
||||
|
||||
static unsigned long xen_read_cr3(void)
|
||||
{
|
||||
return x86_read_percpu(xen_cr3);
|
||||
}
|
||||
|
||||
static void xen_write_cr3(unsigned long cr3)
|
||||
{
|
||||
if (cr3 == x86_read_percpu(xen_cr3)) {
|
||||
/* just a simple tlb flush */
|
||||
xen_flush_tlb();
|
||||
return;
|
||||
}
|
||||
|
||||
x86_write_percpu(xen_cr3, cr3);
|
||||
|
||||
|
||||
{
|
||||
struct mmuext_op *op;
|
||||
struct multicall_space mcs = xen_mc_entry(sizeof(*op));
|
||||
unsigned long mfn = pfn_to_mfn(PFN_DOWN(cr3));
|
||||
|
||||
op = mcs.args;
|
||||
op->cmd = MMUEXT_NEW_BASEPTR;
|
||||
op->arg1.mfn = mfn;
|
||||
|
||||
MULTI_mmuext_op(mcs.mc, op, 1, NULL, DOMID_SELF);
|
||||
|
||||
xen_mc_issue(PARAVIRT_LAZY_CPU);
|
||||
}
|
||||
}
|
||||
|
||||
static void xen_alloc_pt(struct mm_struct *mm, u32 pfn)
|
||||
{
|
||||
/* XXX pfn isn't necessarily a lowmem page */
|
||||
make_lowmem_page_readonly(__va(PFN_PHYS(pfn)));
|
||||
}
|
||||
|
||||
static void xen_alloc_pd(u32 pfn)
|
||||
{
|
||||
make_lowmem_page_readonly(__va(PFN_PHYS(pfn)));
|
||||
}
|
||||
|
||||
static void xen_release_pd(u32 pfn)
|
||||
{
|
||||
make_lowmem_page_readwrite(__va(PFN_PHYS(pfn)));
|
||||
}
|
||||
|
||||
static void xen_release_pt(u32 pfn)
|
||||
{
|
||||
make_lowmem_page_readwrite(__va(PFN_PHYS(pfn)));
|
||||
}
|
||||
|
||||
static void xen_alloc_pd_clone(u32 pfn, u32 clonepfn,
|
||||
u32 start, u32 count)
|
||||
{
|
||||
xen_alloc_pd(pfn);
|
||||
}
|
||||
|
||||
static __init void xen_pagetable_setup_start(pgd_t *base)
|
||||
{
|
||||
pgd_t *xen_pgd = (pgd_t *)xen_start_info->pt_base;
|
||||
|
||||
init_mm.pgd = base;
|
||||
/*
|
||||
* copy top-level of Xen-supplied pagetable into place. For
|
||||
* !PAE we can use this as-is, but for PAE it is a stand-in
|
||||
* while we copy the pmd pages.
|
||||
*/
|
||||
memcpy(base, xen_pgd, PTRS_PER_PGD * sizeof(pgd_t));
|
||||
|
||||
if (PTRS_PER_PMD > 1) {
|
||||
int i;
|
||||
/*
|
||||
* For PAE, need to allocate new pmds, rather than
|
||||
* share Xen's, since Xen doesn't like pmd's being
|
||||
* shared between address spaces.
|
||||
*/
|
||||
for (i = 0; i < PTRS_PER_PGD; i++) {
|
||||
if (pgd_val_ma(xen_pgd[i]) & _PAGE_PRESENT) {
|
||||
pmd_t *pmd = (pmd_t *)alloc_bootmem_low_pages(PAGE_SIZE);
|
||||
|
||||
memcpy(pmd, (void *)pgd_page_vaddr(xen_pgd[i]),
|
||||
PAGE_SIZE);
|
||||
|
||||
xen_alloc_pd(PFN_DOWN(__pa(pmd)));
|
||||
|
||||
set_pgd(&base[i], __pgd(1 + __pa(pmd)));
|
||||
} else
|
||||
pgd_clear(&base[i]);
|
||||
}
|
||||
}
|
||||
|
||||
/* make sure zero_page is mapped RO so we can use it in pagetables */
|
||||
make_lowmem_page_readonly(empty_zero_page);
|
||||
make_lowmem_page_readonly(base);
|
||||
/*
|
||||
* Switch to new pagetable. This is done before
|
||||
* pagetable_init has done anything so that the new pages
|
||||
* added to the table can be prepared properly for Xen.
|
||||
*/
|
||||
xen_write_cr3(__pa(base));
|
||||
}
|
||||
|
||||
static __init void xen_pagetable_setup_done(pgd_t *base)
|
||||
{
|
||||
if (!xen_feature(XENFEAT_auto_translated_physmap)) {
|
||||
/*
|
||||
* Create a mapping for the shared info page.
|
||||
* Should be set_fixmap(), but shared_info is a machine
|
||||
* address with no corresponding pseudo-phys address.
|
||||
*/
|
||||
#if 0
|
||||
set_pte_mfn(fix_to_virt(FIX_PARAVIRT_BOOTMAP),
|
||||
PFN_DOWN(xen_start_info->shared_info),
|
||||
PAGE_KERNEL);
|
||||
#endif
|
||||
|
||||
HYPERVISOR_shared_info =
|
||||
(struct shared_info *)fix_to_virt(FIX_PARAVIRT_BOOTMAP);
|
||||
|
||||
} else
|
||||
HYPERVISOR_shared_info =
|
||||
(struct shared_info *)__va(xen_start_info->shared_info);
|
||||
|
||||
#if 0
|
||||
xen_pgd_pin(base);
|
||||
#endif
|
||||
|
||||
xen_vcpu_setup(smp_processor_id());
|
||||
}
|
||||
|
||||
static const struct paravirt_ops xen_paravirt_ops __initdata = {
|
||||
.paravirt_enabled = 1,
|
||||
.shared_kernel_pmd = 0,
|
||||
|
||||
.name = "Xen",
|
||||
.banner = xen_banner,
|
||||
|
||||
.patch = paravirt_patch_default,
|
||||
|
||||
.memory_setup = xen_memory_setup,
|
||||
.arch_setup = xen_arch_setup,
|
||||
|
||||
.cpuid = xen_cpuid,
|
||||
|
||||
.set_debugreg = xen_set_debugreg,
|
||||
.get_debugreg = xen_get_debugreg,
|
||||
|
||||
.clts = native_clts,
|
||||
|
||||
.read_cr0 = native_read_cr0,
|
||||
.write_cr0 = native_write_cr0,
|
||||
|
||||
.read_cr2 = xen_read_cr2,
|
||||
.write_cr2 = native_write_cr2,
|
||||
|
||||
.read_cr3 = xen_read_cr3,
|
||||
.write_cr3 = xen_write_cr3,
|
||||
|
||||
.read_cr4 = native_read_cr4,
|
||||
.read_cr4_safe = native_read_cr4_safe,
|
||||
.write_cr4 = xen_write_cr4,
|
||||
|
||||
.save_fl = xen_save_fl,
|
||||
.restore_fl = xen_restore_fl,
|
||||
.irq_disable = xen_irq_disable,
|
||||
.irq_enable = xen_irq_enable,
|
||||
.safe_halt = xen_safe_halt,
|
||||
.halt = xen_halt,
|
||||
.wbinvd = native_wbinvd,
|
||||
|
||||
.read_msr = native_read_msr_safe,
|
||||
.write_msr = native_write_msr_safe,
|
||||
.read_tsc = native_read_tsc,
|
||||
.read_pmc = native_read_pmc,
|
||||
|
||||
.iret = (void *)&hypercall_page[__HYPERVISOR_iret],
|
||||
.irq_enable_sysexit = NULL, /* never called */
|
||||
|
||||
.load_tr_desc = paravirt_nop,
|
||||
.set_ldt = xen_set_ldt,
|
||||
.load_gdt = xen_load_gdt,
|
||||
.load_idt = xen_load_idt,
|
||||
.load_tls = xen_load_tls,
|
||||
|
||||
.store_gdt = native_store_gdt,
|
||||
.store_idt = native_store_idt,
|
||||
.store_tr = xen_store_tr,
|
||||
|
||||
.write_ldt_entry = xen_write_ldt_entry,
|
||||
.write_gdt_entry = xen_write_gdt_entry,
|
||||
.write_idt_entry = xen_write_idt_entry,
|
||||
.load_esp0 = xen_load_esp0,
|
||||
|
||||
.set_iopl_mask = xen_set_iopl_mask,
|
||||
.io_delay = xen_io_delay,
|
||||
|
||||
#ifdef CONFIG_X86_LOCAL_APIC
|
||||
.apic_write = paravirt_nop,
|
||||
.apic_write_atomic = paravirt_nop,
|
||||
.apic_read = xen_apic_read,
|
||||
.setup_boot_clock = paravirt_nop,
|
||||
.setup_secondary_clock = paravirt_nop,
|
||||
.startup_ipi_hook = paravirt_nop,
|
||||
#endif
|
||||
|
||||
.flush_tlb_user = xen_flush_tlb,
|
||||
.flush_tlb_kernel = xen_flush_tlb,
|
||||
.flush_tlb_single = xen_flush_tlb_single,
|
||||
|
||||
.pte_update = paravirt_nop,
|
||||
.pte_update_defer = paravirt_nop,
|
||||
|
||||
.pagetable_setup_start = xen_pagetable_setup_start,
|
||||
.pagetable_setup_done = xen_pagetable_setup_done,
|
||||
|
||||
.alloc_pt = xen_alloc_pt,
|
||||
.alloc_pd = xen_alloc_pd,
|
||||
.alloc_pd_clone = xen_alloc_pd_clone,
|
||||
.release_pd = xen_release_pd,
|
||||
.release_pt = xen_release_pt,
|
||||
|
||||
.set_lazy_mode = xen_set_lazy_mode,
|
||||
};
|
||||
|
||||
/* First C function to be called on Xen boot */
|
||||
asmlinkage void __init xen_start_kernel(void)
|
||||
{
|
||||
pgd_t *pgd;
|
||||
|
||||
if (!xen_start_info)
|
||||
return;
|
||||
|
||||
BUG_ON(memcmp(xen_start_info->magic, "xen-3.0", 7) != 0);
|
||||
|
||||
/* Install Xen paravirt ops */
|
||||
paravirt_ops = xen_paravirt_ops;
|
||||
|
||||
xen_setup_features();
|
||||
|
||||
/* Get mfn list */
|
||||
if (!xen_feature(XENFEAT_auto_translated_physmap))
|
||||
phys_to_machine_mapping = (unsigned long *)xen_start_info->mfn_list;
|
||||
|
||||
pgd = (pgd_t *)xen_start_info->pt_base;
|
||||
|
||||
init_pg_tables_end = __pa(pgd) + xen_start_info->nr_pt_frames*PAGE_SIZE;
|
||||
|
||||
init_mm.pgd = pgd; /* use the Xen pagetables to start */
|
||||
|
||||
/* keep using Xen gdt for now; no urgent need to change it */
|
||||
|
||||
x86_write_percpu(xen_cr3, __pa(pgd));
|
||||
xen_vcpu_setup(0);
|
||||
|
||||
paravirt_ops.kernel_rpl = 1;
|
||||
if (xen_feature(XENFEAT_supervisor_mode_kernel))
|
||||
paravirt_ops.kernel_rpl = 0;
|
||||
|
||||
/* set the limit of our address space */
|
||||
reserve_top_address(-HYPERVISOR_VIRT_START + 2 * PAGE_SIZE);
|
||||
|
||||
/* set up basic CPUID stuff */
|
||||
cpu_detect(&new_cpu_data);
|
||||
new_cpu_data.hard_math = 1;
|
||||
new_cpu_data.x86_capability[0] = cpuid_edx(1);
|
||||
|
||||
/* Poke various useful things into boot_params */
|
||||
LOADER_TYPE = (9 << 4) | 0;
|
||||
INITRD_START = xen_start_info->mod_start ? __pa(xen_start_info->mod_start) : 0;
|
||||
INITRD_SIZE = xen_start_info->mod_len;
|
||||
|
||||
/* Start the world */
|
||||
start_kernel();
|
||||
}
|
29
arch/i386/xen/features.c
Normal file
29
arch/i386/xen/features.c
Normal file
|
@ -0,0 +1,29 @@
|
|||
/******************************************************************************
|
||||
* features.c
|
||||
*
|
||||
* Xen feature flags.
|
||||
*
|
||||
* Copyright (c) 2006, Ian Campbell, XenSource Inc.
|
||||
*/
|
||||
#include <linux/types.h>
|
||||
#include <linux/cache.h>
|
||||
#include <linux/module.h>
|
||||
#include <asm/xen/hypervisor.h>
|
||||
#include <xen/features.h>
|
||||
|
||||
u8 xen_features[XENFEAT_NR_SUBMAPS * 32] __read_mostly;
|
||||
EXPORT_SYMBOL_GPL(xen_features);
|
||||
|
||||
void xen_setup_features(void)
|
||||
{
|
||||
struct xen_feature_info fi;
|
||||
int i, j;
|
||||
|
||||
for (i = 0; i < XENFEAT_NR_SUBMAPS; i++) {
|
||||
fi.submap_idx = i;
|
||||
if (HYPERVISOR_xen_version(XENVER_get_features, &fi) < 0)
|
||||
break;
|
||||
for (j = 0; j < 32; j++)
|
||||
xen_features[i * 32 + j] = !!(fi.submap & 1<<j);
|
||||
}
|
||||
}
|
89
arch/i386/xen/multicalls.c
Normal file
89
arch/i386/xen/multicalls.c
Normal file
|
@ -0,0 +1,89 @@
|
|||
/*
|
||||
* Xen hypercall batching.
|
||||
*
|
||||
* Xen allows multiple hypercalls to be issued at once, using the
|
||||
* multicall interface. This allows the cost of trapping into the
|
||||
* hypervisor to be amortized over several calls.
|
||||
*
|
||||
* This file implements a simple interface for multicalls. There's a
|
||||
* per-cpu buffer of outstanding multicalls. When you want to queue a
|
||||
* multicall for issuing, you can allocate a multicall slot for the
|
||||
* call and its arguments, along with storage for space which is
|
||||
* pointed to by the arguments (for passing pointers to structures,
|
||||
* etc). When the multicall is actually issued, all the space for the
|
||||
* commands and allocated memory is freed for reuse.
|
||||
*
|
||||
* Multicalls are flushed whenever any of the buffers get full, or
|
||||
* when explicitly requested. There's no way to get per-multicall
|
||||
* return results back. It will BUG if any of the multicalls fail.
|
||||
*
|
||||
* Jeremy Fitzhardinge <jeremy@xensource.com>, XenSource Inc, 2007
|
||||
*/
|
||||
#include <linux/percpu.h>
|
||||
|
||||
#include <asm/xen/hypercall.h>
|
||||
|
||||
#include "multicalls.h"
|
||||
|
||||
#define MC_BATCH 8
|
||||
#define MC_ARGS (MC_BATCH * 32 / sizeof(u64))
|
||||
|
||||
struct mc_buffer {
|
||||
struct multicall_entry entries[MC_BATCH];
|
||||
u64 args[MC_ARGS];
|
||||
unsigned mcidx, argidx;
|
||||
};
|
||||
|
||||
static DEFINE_PER_CPU(struct mc_buffer, mc_buffer);
|
||||
DEFINE_PER_CPU(unsigned long, xen_mc_irq_flags);
|
||||
|
||||
void xen_mc_flush(void)
|
||||
{
|
||||
struct mc_buffer *b = &get_cpu_var(mc_buffer);
|
||||
int ret = 0;
|
||||
unsigned long flags;
|
||||
|
||||
/* Disable interrupts in case someone comes in and queues
|
||||
something in the middle */
|
||||
local_irq_save(flags);
|
||||
|
||||
if (b->mcidx) {
|
||||
int i;
|
||||
|
||||
if (HYPERVISOR_multicall(b->entries, b->mcidx) != 0)
|
||||
BUG();
|
||||
for (i = 0; i < b->mcidx; i++)
|
||||
if (b->entries[i].result < 0)
|
||||
ret++;
|
||||
b->mcidx = 0;
|
||||
b->argidx = 0;
|
||||
} else
|
||||
BUG_ON(b->argidx != 0);
|
||||
|
||||
put_cpu_var(mc_buffer);
|
||||
local_irq_restore(flags);
|
||||
|
||||
BUG_ON(ret);
|
||||
}
|
||||
|
||||
struct multicall_space __xen_mc_entry(size_t args)
|
||||
{
|
||||
struct mc_buffer *b = &get_cpu_var(mc_buffer);
|
||||
struct multicall_space ret;
|
||||
unsigned argspace = (args + sizeof(u64) - 1) / sizeof(u64);
|
||||
|
||||
BUG_ON(argspace > MC_ARGS);
|
||||
|
||||
if (b->mcidx == MC_BATCH ||
|
||||
(b->argidx + argspace) > MC_ARGS)
|
||||
xen_mc_flush();
|
||||
|
||||
ret.mc = &b->entries[b->mcidx];
|
||||
b->mcidx++;
|
||||
ret.args = &b->args[b->argidx];
|
||||
b->argidx += argspace;
|
||||
|
||||
put_cpu_var(mc_buffer);
|
||||
|
||||
return ret;
|
||||
}
|
45
arch/i386/xen/multicalls.h
Normal file
45
arch/i386/xen/multicalls.h
Normal file
|
@ -0,0 +1,45 @@
|
|||
#ifndef _XEN_MULTICALLS_H
|
||||
#define _XEN_MULTICALLS_H
|
||||
|
||||
#include "xen-ops.h"
|
||||
|
||||
/* Multicalls */
|
||||
struct multicall_space
|
||||
{
|
||||
struct multicall_entry *mc;
|
||||
void *args;
|
||||
};
|
||||
|
||||
/* Allocate room for a multicall and its args */
|
||||
struct multicall_space __xen_mc_entry(size_t args);
|
||||
|
||||
DECLARE_PER_CPU(unsigned long, xen_mc_irq_flags);
|
||||
|
||||
/* Call to start a batch of multiple __xen_mc_entry()s. Must be
|
||||
paired with xen_mc_issue() */
|
||||
static inline void xen_mc_batch(void)
|
||||
{
|
||||
/* need to disable interrupts until this entry is complete */
|
||||
local_irq_save(__get_cpu_var(xen_mc_irq_flags));
|
||||
}
|
||||
|
||||
static inline struct multicall_space xen_mc_entry(size_t args)
|
||||
{
|
||||
xen_mc_batch();
|
||||
return __xen_mc_entry(args);
|
||||
}
|
||||
|
||||
/* Flush all pending multicalls */
|
||||
void xen_mc_flush(void);
|
||||
|
||||
/* Issue a multicall if we're not in a lazy mode */
|
||||
static inline void xen_mc_issue(unsigned mode)
|
||||
{
|
||||
if ((xen_get_lazy_mode() & mode) == 0)
|
||||
xen_mc_flush();
|
||||
|
||||
/* restore flags saved in xen_mc_batch */
|
||||
local_irq_restore(x86_read_percpu(xen_mc_irq_flags));
|
||||
}
|
||||
|
||||
#endif /* _XEN_MULTICALLS_H */
|
97
arch/i386/xen/setup.c
Normal file
97
arch/i386/xen/setup.c
Normal file
|
@ -0,0 +1,97 @@
|
|||
/*
|
||||
* Machine specific setup for xen
|
||||
*
|
||||
* Jeremy Fitzhardinge <jeremy@xensource.com>, XenSource Inc, 2007
|
||||
*/
|
||||
|
||||
#include <linux/module.h>
|
||||
#include <linux/sched.h>
|
||||
#include <linux/mm.h>
|
||||
#include <linux/pm.h>
|
||||
|
||||
#include <asm/elf.h>
|
||||
#include <asm/e820.h>
|
||||
#include <asm/setup.h>
|
||||
#include <asm/xen/hypervisor.h>
|
||||
#include <asm/xen/hypercall.h>
|
||||
|
||||
#include <xen/interface/physdev.h>
|
||||
#include <xen/features.h>
|
||||
|
||||
#include "xen-ops.h"
|
||||
|
||||
/* These are code, but not functions. Defined in entry.S */
|
||||
extern const char xen_hypervisor_callback[];
|
||||
extern const char xen_failsafe_callback[];
|
||||
|
||||
static __initdata struct shared_info init_shared;
|
||||
|
||||
/*
|
||||
* Point at some empty memory to start with. We map the real shared_info
|
||||
* page as soon as fixmap is up and running.
|
||||
*/
|
||||
struct shared_info *HYPERVISOR_shared_info = &init_shared;
|
||||
|
||||
unsigned long *phys_to_machine_mapping;
|
||||
EXPORT_SYMBOL(phys_to_machine_mapping);
|
||||
|
||||
/**
|
||||
* machine_specific_memory_setup - Hook for machine specific memory setup.
|
||||
**/
|
||||
|
||||
char * __init xen_memory_setup(void)
|
||||
{
|
||||
unsigned long max_pfn = xen_start_info->nr_pages;
|
||||
|
||||
e820.nr_map = 0;
|
||||
add_memory_region(0, PFN_PHYS(max_pfn), E820_RAM);
|
||||
|
||||
return "Xen";
|
||||
}
|
||||
|
||||
static void xen_idle(void)
|
||||
{
|
||||
local_irq_disable();
|
||||
|
||||
if (need_resched())
|
||||
local_irq_enable();
|
||||
else {
|
||||
current_thread_info()->status &= ~TS_POLLING;
|
||||
smp_mb__after_clear_bit();
|
||||
safe_halt();
|
||||
current_thread_info()->status |= TS_POLLING;
|
||||
}
|
||||
}
|
||||
|
||||
void __init xen_arch_setup(void)
|
||||
{
|
||||
struct physdev_set_iopl set_iopl;
|
||||
int rc;
|
||||
|
||||
HYPERVISOR_vm_assist(VMASST_CMD_enable, VMASST_TYPE_4gb_segments);
|
||||
HYPERVISOR_vm_assist(VMASST_CMD_enable, VMASST_TYPE_writable_pagetables);
|
||||
|
||||
if (!xen_feature(XENFEAT_auto_translated_physmap))
|
||||
HYPERVISOR_vm_assist(VMASST_CMD_enable, VMASST_TYPE_pae_extended_cr3);
|
||||
|
||||
HYPERVISOR_set_callbacks(__KERNEL_CS, (unsigned long)xen_hypervisor_callback,
|
||||
__KERNEL_CS, (unsigned long)xen_failsafe_callback);
|
||||
|
||||
set_iopl.iopl = 1;
|
||||
rc = HYPERVISOR_physdev_op(PHYSDEVOP_set_iopl, &set_iopl);
|
||||
if (rc != 0)
|
||||
printk(KERN_INFO "physdev_op failed %d\n", rc);
|
||||
|
||||
#ifdef CONFIG_ACPI
|
||||
if (!(xen_start_info->flags & SIF_INITDOMAIN)) {
|
||||
printk(KERN_INFO "ACPI in unprivileged domain disabled\n");
|
||||
disable_acpi();
|
||||
}
|
||||
#endif
|
||||
|
||||
memcpy(boot_command_line, xen_start_info->cmd_line,
|
||||
MAX_GUEST_CMDLINE > COMMAND_LINE_SIZE ?
|
||||
COMMAND_LINE_SIZE : MAX_GUEST_CMDLINE);
|
||||
|
||||
pm_idle = xen_idle;
|
||||
}
|
36
arch/i386/xen/xen-head.S
Normal file
36
arch/i386/xen/xen-head.S
Normal file
|
@ -0,0 +1,36 @@
|
|||
/* Xen-specific pieces of head.S, intended to be included in the right
|
||||
place in head.S */
|
||||
|
||||
#ifdef CONFIG_XEN
|
||||
|
||||
#include <linux/elfnote.h>
|
||||
#include <asm/boot.h>
|
||||
#include <xen/interface/elfnote.h>
|
||||
|
||||
ENTRY(startup_xen)
|
||||
movl %esi,xen_start_info
|
||||
cld
|
||||
movl $(init_thread_union+THREAD_SIZE),%esp
|
||||
jmp xen_start_kernel
|
||||
|
||||
.pushsection ".bss.page_aligned"
|
||||
.align PAGE_SIZE_asm
|
||||
ENTRY(hypercall_page)
|
||||
.skip 0x1000
|
||||
.popsection
|
||||
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_GUEST_OS, .asciz "linux")
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_GUEST_VERSION, .asciz "2.6")
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_XEN_VERSION, .asciz "xen-3.0")
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_VIRT_BASE, .long __PAGE_OFFSET)
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_ENTRY, .long startup_xen)
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_HYPERCALL_PAGE, .long hypercall_page)
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_FEATURES, .asciz "!writable_page_tables|pae_pgdir_above_4gb")
|
||||
#ifdef CONFIG_X86_PAE
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_PAE_MODE, .asciz "yes")
|
||||
#else
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_PAE_MODE, .asciz "no")
|
||||
#endif
|
||||
ELFNOTE(Xen, XEN_ELFNOTE_LOADER, .asciz "generic")
|
||||
|
||||
#endif /*CONFIG_XEN */
|
31
arch/i386/xen/xen-ops.h
Normal file
31
arch/i386/xen/xen-ops.h
Normal file
|
@ -0,0 +1,31 @@
|
|||
#ifndef XEN_OPS_H
|
||||
#define XEN_OPS_H
|
||||
|
||||
#include <linux/init.h>
|
||||
#include <linux/clocksource.h>
|
||||
|
||||
DECLARE_PER_CPU(struct vcpu_info *, xen_vcpu);
|
||||
DECLARE_PER_CPU(unsigned long, xen_cr3);
|
||||
|
||||
extern struct start_info *xen_start_info;
|
||||
extern struct shared_info *HYPERVISOR_shared_info;
|
||||
|
||||
char * __init xen_memory_setup(void);
|
||||
void __init xen_arch_setup(void);
|
||||
void __init xen_init_IRQ(void);
|
||||
|
||||
unsigned long xen_cpu_khz(void);
|
||||
void __init xen_time_init(void);
|
||||
unsigned long xen_get_wallclock(void);
|
||||
int xen_set_wallclock(unsigned long time);
|
||||
cycle_t xen_clocksource_read(void);
|
||||
|
||||
DECLARE_PER_CPU(enum paravirt_lazy_mode, xen_lazy_mode);
|
||||
|
||||
static inline unsigned xen_get_lazy_mode(void)
|
||||
{
|
||||
return x86_read_percpu(xen_lazy_mode);
|
||||
}
|
||||
|
||||
|
||||
#endif /* XEN_OPS_H */
|
|
@ -41,6 +41,7 @@ extern int irqbalance_disable(char *str);
|
|||
extern void fixup_irqs(cpumask_t map);
|
||||
#endif
|
||||
|
||||
unsigned int do_IRQ(struct pt_regs *regs);
|
||||
void init_IRQ(void);
|
||||
void __init native_init_IRQ(void);
|
||||
|
||||
|
|
|
@ -392,4 +392,22 @@ MULTI_mmuext_op(struct multicall_entry *mcl, struct mmuext_op *op, int count,
|
|||
mcl->args[2] = (unsigned long)success_count;
|
||||
mcl->args[3] = domid;
|
||||
}
|
||||
|
||||
static inline void
|
||||
MULTI_set_gdt(struct multicall_entry *mcl, unsigned long *frames, int entries)
|
||||
{
|
||||
mcl->op = __HYPERVISOR_set_gdt;
|
||||
mcl->args[0] = (unsigned long)frames;
|
||||
mcl->args[1] = entries;
|
||||
}
|
||||
|
||||
static inline void
|
||||
MULTI_stack_switch(struct multicall_entry *mcl,
|
||||
unsigned long ss, unsigned long esp)
|
||||
{
|
||||
mcl->op = __HYPERVISOR_stack_switch;
|
||||
mcl->args[0] = ss;
|
||||
mcl->args[1] = esp;
|
||||
}
|
||||
|
||||
#endif /* __HYPERCALL_H__ */
|
||||
|
|
23
include/xen/features.h
Normal file
23
include/xen/features.h
Normal file
|
@ -0,0 +1,23 @@
|
|||
/******************************************************************************
|
||||
* features.h
|
||||
*
|
||||
* Query the features reported by Xen.
|
||||
*
|
||||
* Copyright (c) 2006, Ian Campbell
|
||||
*/
|
||||
|
||||
#ifndef __XEN_FEATURES_H__
|
||||
#define __XEN_FEATURES_H__
|
||||
|
||||
#include <xen/interface/features.h>
|
||||
|
||||
void xen_setup_features(void);
|
||||
|
||||
extern u8 xen_features[XENFEAT_NR_SUBMAPS * 32];
|
||||
|
||||
static inline int xen_feature(int flag)
|
||||
{
|
||||
return xen_features[flag];
|
||||
}
|
||||
|
||||
#endif /* __ASM_XEN_FEATURES_H__ */
|
179
include/xen/page.h
Normal file
179
include/xen/page.h
Normal file
|
@ -0,0 +1,179 @@
|
|||
#ifndef __XEN_PAGE_H
|
||||
#define __XEN_PAGE_H
|
||||
|
||||
#include <linux/pfn.h>
|
||||
|
||||
#include <asm/uaccess.h>
|
||||
|
||||
#include <xen/features.h>
|
||||
|
||||
#ifdef CONFIG_X86_PAE
|
||||
/* Xen machine address */
|
||||
typedef struct xmaddr {
|
||||
unsigned long long maddr;
|
||||
} xmaddr_t;
|
||||
|
||||
/* Xen pseudo-physical address */
|
||||
typedef struct xpaddr {
|
||||
unsigned long long paddr;
|
||||
} xpaddr_t;
|
||||
#else
|
||||
/* Xen machine address */
|
||||
typedef struct xmaddr {
|
||||
unsigned long maddr;
|
||||
} xmaddr_t;
|
||||
|
||||
/* Xen pseudo-physical address */
|
||||
typedef struct xpaddr {
|
||||
unsigned long paddr;
|
||||
} xpaddr_t;
|
||||
#endif
|
||||
|
||||
#define XMADDR(x) ((xmaddr_t) { .maddr = (x) })
|
||||
#define XPADDR(x) ((xpaddr_t) { .paddr = (x) })
|
||||
|
||||
/**** MACHINE <-> PHYSICAL CONVERSION MACROS ****/
|
||||
#define INVALID_P2M_ENTRY (~0UL)
|
||||
#define FOREIGN_FRAME_BIT (1UL<<31)
|
||||
#define FOREIGN_FRAME(m) ((m) | FOREIGN_FRAME_BIT)
|
||||
|
||||
extern unsigned long *phys_to_machine_mapping;
|
||||
|
||||
static inline unsigned long pfn_to_mfn(unsigned long pfn)
|
||||
{
|
||||
if (xen_feature(XENFEAT_auto_translated_physmap))
|
||||
return pfn;
|
||||
|
||||
return phys_to_machine_mapping[(unsigned int)(pfn)] &
|
||||
~FOREIGN_FRAME_BIT;
|
||||
}
|
||||
|
||||
static inline int phys_to_machine_mapping_valid(unsigned long pfn)
|
||||
{
|
||||
if (xen_feature(XENFEAT_auto_translated_physmap))
|
||||
return 1;
|
||||
|
||||
return (phys_to_machine_mapping[pfn] != INVALID_P2M_ENTRY);
|
||||
}
|
||||
|
||||
static inline unsigned long mfn_to_pfn(unsigned long mfn)
|
||||
{
|
||||
unsigned long pfn;
|
||||
|
||||
if (xen_feature(XENFEAT_auto_translated_physmap))
|
||||
return mfn;
|
||||
|
||||
#if 0
|
||||
if (unlikely((mfn >> machine_to_phys_order) != 0))
|
||||
return max_mapnr;
|
||||
#endif
|
||||
|
||||
pfn = 0;
|
||||
/*
|
||||
* The array access can fail (e.g., device space beyond end of RAM).
|
||||
* In such cases it doesn't matter what we return (we return garbage),
|
||||
* but we must handle the fault without crashing!
|
||||
*/
|
||||
__get_user(pfn, &machine_to_phys_mapping[mfn]);
|
||||
|
||||
return pfn;
|
||||
}
|
||||
|
||||
static inline xmaddr_t phys_to_machine(xpaddr_t phys)
|
||||
{
|
||||
unsigned offset = phys.paddr & ~PAGE_MASK;
|
||||
return XMADDR(PFN_PHYS((u64)pfn_to_mfn(PFN_DOWN(phys.paddr))) | offset);
|
||||
}
|
||||
|
||||
static inline xpaddr_t machine_to_phys(xmaddr_t machine)
|
||||
{
|
||||
unsigned offset = machine.maddr & ~PAGE_MASK;
|
||||
return XPADDR(PFN_PHYS((u64)mfn_to_pfn(PFN_DOWN(machine.maddr))) | offset);
|
||||
}
|
||||
|
||||
/*
|
||||
* We detect special mappings in one of two ways:
|
||||
* 1. If the MFN is an I/O page then Xen will set the m2p entry
|
||||
* to be outside our maximum possible pseudophys range.
|
||||
* 2. If the MFN belongs to a different domain then we will certainly
|
||||
* not have MFN in our p2m table. Conversely, if the page is ours,
|
||||
* then we'll have p2m(m2p(MFN))==MFN.
|
||||
* If we detect a special mapping then it doesn't have a 'struct page'.
|
||||
* We force !pfn_valid() by returning an out-of-range pointer.
|
||||
*
|
||||
* NB. These checks require that, for any MFN that is not in our reservation,
|
||||
* there is no PFN such that p2m(PFN) == MFN. Otherwise we can get confused if
|
||||
* we are foreign-mapping the MFN, and the other domain as m2p(MFN) == PFN.
|
||||
* Yikes! Various places must poke in INVALID_P2M_ENTRY for safety.
|
||||
*
|
||||
* NB2. When deliberately mapping foreign pages into the p2m table, you *must*
|
||||
* use FOREIGN_FRAME(). This will cause pte_pfn() to choke on it, as we
|
||||
* require. In all the cases we care about, the FOREIGN_FRAME bit is
|
||||
* masked (e.g., pfn_to_mfn()) so behaviour there is correct.
|
||||
*/
|
||||
static inline unsigned long mfn_to_local_pfn(unsigned long mfn)
|
||||
{
|
||||
extern unsigned long max_mapnr;
|
||||
unsigned long pfn = mfn_to_pfn(mfn);
|
||||
if ((pfn < max_mapnr)
|
||||
&& !xen_feature(XENFEAT_auto_translated_physmap)
|
||||
&& (phys_to_machine_mapping[pfn] != mfn))
|
||||
return max_mapnr; /* force !pfn_valid() */
|
||||
return pfn;
|
||||
}
|
||||
|
||||
static inline void set_phys_to_machine(unsigned long pfn, unsigned long mfn)
|
||||
{
|
||||
if (xen_feature(XENFEAT_auto_translated_physmap)) {
|
||||
BUG_ON(pfn != mfn && mfn != INVALID_P2M_ENTRY);
|
||||
return;
|
||||
}
|
||||
phys_to_machine_mapping[pfn] = mfn;
|
||||
}
|
||||
|
||||
/* VIRT <-> MACHINE conversion */
|
||||
#define virt_to_machine(v) (phys_to_machine(XPADDR(__pa(v))))
|
||||
#define virt_to_mfn(v) (pfn_to_mfn(PFN_DOWN(__pa(v))))
|
||||
#define mfn_to_virt(m) (__va(mfn_to_pfn(m) << PAGE_SHIFT))
|
||||
|
||||
#ifdef CONFIG_X86_PAE
|
||||
#define pte_mfn(_pte) (((_pte).pte_low >> PAGE_SHIFT) | \
|
||||
(((_pte).pte_high & 0xfff) << (32-PAGE_SHIFT)))
|
||||
|
||||
static inline pte_t mfn_pte(unsigned long page_nr, pgprot_t pgprot)
|
||||
{
|
||||
pte_t pte;
|
||||
|
||||
pte.pte_high = (page_nr >> (32 - PAGE_SHIFT)) |
|
||||
(pgprot_val(pgprot) >> 32);
|
||||
pte.pte_high &= (__supported_pte_mask >> 32);
|
||||
pte.pte_low = ((page_nr << PAGE_SHIFT) | pgprot_val(pgprot));
|
||||
pte.pte_low &= __supported_pte_mask;
|
||||
|
||||
return pte;
|
||||
}
|
||||
|
||||
static inline unsigned long long pte_val_ma(pte_t x)
|
||||
{
|
||||
return ((unsigned long long)x.pte_high << 32) | x.pte_low;
|
||||
}
|
||||
#define pmd_val_ma(v) ((v).pmd)
|
||||
#define pud_val_ma(v) ((v).pgd.pgd)
|
||||
#define __pte_ma(x) ((pte_t) { .pte_low = (x), .pte_high = (x)>>32 } )
|
||||
#define __pmd_ma(x) ((pmd_t) { (x) } )
|
||||
#else /* !X86_PAE */
|
||||
#define pte_mfn(_pte) ((_pte).pte_low >> PAGE_SHIFT)
|
||||
#define mfn_pte(pfn, prot) __pte_ma(((pfn) << PAGE_SHIFT) | pgprot_val(prot))
|
||||
#define pte_val_ma(x) ((x).pte_low)
|
||||
#define pmd_val_ma(v) ((v).pud.pgd.pgd)
|
||||
#define __pte_ma(x) ((pte_t) { (x) } )
|
||||
#endif /* CONFIG_X86_PAE */
|
||||
|
||||
#define pgd_val_ma(x) ((x).pgd)
|
||||
|
||||
|
||||
xmaddr_t arbitrary_virt_to_machine(unsigned long address);
|
||||
void make_lowmem_page_readonly(void *vaddr);
|
||||
void make_lowmem_page_readwrite(void *vaddr);
|
||||
|
||||
#endif /* __XEN_PAGE_H */
|
Loading…
Reference in a new issue