Merge remote-tracking branch 'regulator/for-next' into tmp
This commit is contained in:
commit
6dfae59d37
27
Documentation/devicetree/bindings/regulator/mp886x.txt
Normal file
27
Documentation/devicetree/bindings/regulator/mp886x.txt
Normal file
|
@ -0,0 +1,27 @@
|
|||
Monolithic Power Systems MP8867/MP8869 voltage regulator
|
||||
|
||||
Required properties:
|
||||
- compatible: Must be one of the following.
|
||||
"mps,mp8867"
|
||||
"mps,mp8869"
|
||||
- reg: I2C slave address.
|
||||
- enable-gpios: enable gpios.
|
||||
- mps,fb-voltage-divider: An array of two integers containing the resistor
|
||||
values R1 and R2 of the feedback voltage divider in kilo ohms.
|
||||
|
||||
Any property defined as part of the core regulator binding, defined in
|
||||
./regulator.txt, can also be used.
|
||||
|
||||
Example:
|
||||
|
||||
vcpu: regulator@62 {
|
||||
compatible = "mps,mp8869";
|
||||
regulator-name = "vcpu";
|
||||
regulator-min-microvolt = <700000>;
|
||||
regulator-max-microvolt = <850000>;
|
||||
regulator-always-on;
|
||||
regulator-boot-on;
|
||||
enable-gpios = <&porta 1 GPIO_ACTIVE_LOW>;
|
||||
mps,fb-voltage-divider = <80 240>;
|
||||
reg = <0x62>;
|
||||
};
|
|
@ -26,6 +26,7 @@ Regulator nodes are identified by their compatible:
|
|||
"qcom,rpm-pm8994-regulators"
|
||||
"qcom,rpm-pm8998-regulators"
|
||||
"qcom,rpm-pma8084-regulators"
|
||||
"qcom,rpm-pmi8994-regulators"
|
||||
"qcom,rpm-pmi8998-regulators"
|
||||
"qcom,rpm-pms405-regulators"
|
||||
|
||||
|
@ -143,6 +144,15 @@ Regulator nodes are identified by their compatible:
|
|||
Definition: reference to regulator supplying the input pin, as
|
||||
described in the data sheet
|
||||
|
||||
- vdd_s1-supply:
|
||||
- vdd_s2-supply:
|
||||
- vdd_s3-supply:
|
||||
- vdd_bst_byp-supply:
|
||||
Usage: optional (pmi8994 only)
|
||||
Value type: <phandle>
|
||||
Definition: reference to regulator supplying the input pin, as
|
||||
described in the data sheet
|
||||
|
||||
- vdd_s1-supply:
|
||||
- vdd_s2-supply:
|
||||
- vdd_s3-supply:
|
||||
|
@ -259,6 +269,9 @@ pma8084:
|
|||
l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20,
|
||||
l21, l22, l23, l24, l25, l26, l27, lvs1, lvs2, lvs3, lvs4, 5vs1
|
||||
|
||||
pmi8994:
|
||||
s1, s2, s3, boost-bypass
|
||||
|
||||
pmi8998:
|
||||
bob
|
||||
|
||||
|
|
|
@ -0,0 +1,42 @@
|
|||
# SPDX-License-Identifier: GPL-2.0
|
||||
%YAML 1.2
|
||||
---
|
||||
$id: http://devicetree.org/schemas/regulator/vqmmc-ipq4019-regulator.yaml#
|
||||
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||||
|
||||
title: Qualcomm IPQ4019 VQMMC SD LDO regulator
|
||||
|
||||
maintainers:
|
||||
- Robert Marko <robert.marko@sartura.hr>
|
||||
|
||||
description: |
|
||||
Qualcomm IPQ4019 SoC-s feature a built a build SD/EMMC controller,
|
||||
in order to support both 1.8 and 3V I/O voltage levels an LDO
|
||||
controller is also embedded.
|
||||
|
||||
allOf:
|
||||
- $ref: "regulator.yaml#"
|
||||
|
||||
properties:
|
||||
compatible:
|
||||
const: qcom,vqmmc-ipq4019-regulator
|
||||
|
||||
reg:
|
||||
maxItems: 1
|
||||
|
||||
required:
|
||||
- compatible
|
||||
- reg
|
||||
|
||||
examples:
|
||||
- |
|
||||
regulator@1948000 {
|
||||
compatible = "qcom,vqmmc-ipq4019-regulator";
|
||||
reg = <0x01948000 0x4>;
|
||||
regulator-name = "vqmmc";
|
||||
regulator-min-microvolt = <1500000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-always-on;
|
||||
status = "disabled";
|
||||
};
|
||||
...
|
|
@ -635,6 +635,13 @@ config REGULATOR_MP8859
|
|||
Say M here if you want to include support for the regulator as a
|
||||
module. The module will be named "mp8859".
|
||||
|
||||
config REGULATOR_MP886X
|
||||
tristate "MPS MP8869 regulator driver"
|
||||
depends on I2C && (OF || COMPILE_TEST)
|
||||
select REGMAP_I2C
|
||||
help
|
||||
This driver supports the MP8869 voltage regulator.
|
||||
|
||||
config REGULATOR_MPQ7920
|
||||
tristate "Monolithic MPQ7920 PMIC"
|
||||
depends on I2C && OF
|
||||
|
|
|
@ -80,6 +80,7 @@ obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
|
|||
obj-$(CONFIG_REGULATOR_MCP16502) += mcp16502.o
|
||||
obj-$(CONFIG_REGULATOR_MP5416) += mp5416.o
|
||||
obj-$(CONFIG_REGULATOR_MP8859) += mp8859.o
|
||||
obj-$(CONFIG_REGULATOR_MP886X) += mp886x.o
|
||||
obj-$(CONFIG_REGULATOR_MPQ7920) += mpq7920.o
|
||||
obj-$(CONFIG_REGULATOR_MT6311) += mt6311-regulator.o
|
||||
obj-$(CONFIG_REGULATOR_MT6323) += mt6323-regulator.o
|
||||
|
|
|
@ -1849,7 +1849,6 @@ struct regulator *_regulator_get(struct device *dev, const char *id,
|
|||
{
|
||||
struct regulator_dev *rdev;
|
||||
struct regulator *regulator;
|
||||
const char *devname = dev ? dev_name(dev) : "deviceless";
|
||||
struct device_link *link;
|
||||
int ret;
|
||||
|
||||
|
@ -1887,9 +1886,7 @@ struct regulator *_regulator_get(struct device *dev, const char *id,
|
|||
* enabled, even if it isn't hooked up, and just
|
||||
* provide a dummy.
|
||||
*/
|
||||
dev_warn(dev,
|
||||
"%s supply %s not found, using dummy regulator\n",
|
||||
devname, id);
|
||||
dev_warn(dev, "supply %s not found, using dummy regulator\n", id);
|
||||
rdev = dummy_regulator_rdev;
|
||||
get_device(&rdev->dev);
|
||||
break;
|
||||
|
|
|
@ -100,6 +100,7 @@ struct da9063_regulator_info {
|
|||
.desc.vsel_mask = DA9063_V##regl_name##_MASK, \
|
||||
.desc.linear_min_sel = DA9063_V##regl_name##_BIAS, \
|
||||
.sleep = BFIELD(DA9063_REG_V##regl_name##_A, DA9063_LDO_SL), \
|
||||
.suspend = BFIELD(DA9063_REG_##regl_name##_CONT, DA9063_LDO_CONF), \
|
||||
.suspend_sleep = BFIELD(DA9063_REG_V##regl_name##_B, DA9063_LDO_SL), \
|
||||
.suspend_vsel_reg = DA9063_REG_V##regl_name##_B
|
||||
|
||||
|
@ -124,6 +125,7 @@ struct da9063_regulator_info {
|
|||
.desc.vsel_mask = DA9063_VBUCK_MASK, \
|
||||
.desc.linear_min_sel = DA9063_VBUCK_BIAS, \
|
||||
.sleep = BFIELD(DA9063_REG_V##regl_name##_A, DA9063_BUCK_SL), \
|
||||
.suspend = BFIELD(DA9063_REG_##regl_name##_CONT, DA9063_BUCK_CONF), \
|
||||
.suspend_sleep = BFIELD(DA9063_REG_V##regl_name##_B, DA9063_BUCK_SL), \
|
||||
.suspend_vsel_reg = DA9063_REG_V##regl_name##_B, \
|
||||
.mode = BFIELD(DA9063_REG_##regl_name##_CFG, DA9063_BUCK_MODE_MASK)
|
||||
|
@ -232,7 +234,6 @@ static int da9063_buck_set_mode(struct regulator_dev *rdev, unsigned int mode)
|
|||
static unsigned int da9063_buck_get_mode(struct regulator_dev *rdev)
|
||||
{
|
||||
struct da9063_regulator *regl = rdev_get_drvdata(rdev);
|
||||
struct regmap_field *field;
|
||||
unsigned int val;
|
||||
int ret;
|
||||
|
||||
|
@ -253,18 +254,7 @@ static unsigned int da9063_buck_get_mode(struct regulator_dev *rdev)
|
|||
return REGULATOR_MODE_NORMAL;
|
||||
}
|
||||
|
||||
/* Detect current regulator state */
|
||||
ret = regmap_field_read(regl->suspend, &val);
|
||||
if (ret < 0)
|
||||
return 0;
|
||||
|
||||
/* Read regulator mode from proper register, depending on state */
|
||||
if (val)
|
||||
field = regl->suspend_sleep;
|
||||
else
|
||||
field = regl->sleep;
|
||||
|
||||
ret = regmap_field_read(field, &val);
|
||||
ret = regmap_field_read(regl->sleep, &val);
|
||||
if (ret < 0)
|
||||
return 0;
|
||||
|
||||
|
@ -301,21 +291,9 @@ static int da9063_ldo_set_mode(struct regulator_dev *rdev, unsigned int mode)
|
|||
static unsigned int da9063_ldo_get_mode(struct regulator_dev *rdev)
|
||||
{
|
||||
struct da9063_regulator *regl = rdev_get_drvdata(rdev);
|
||||
struct regmap_field *field;
|
||||
int ret, val;
|
||||
|
||||
/* Detect current regulator state */
|
||||
ret = regmap_field_read(regl->suspend, &val);
|
||||
if (ret < 0)
|
||||
return 0;
|
||||
|
||||
/* Read regulator mode from proper register, depending on state */
|
||||
if (val)
|
||||
field = regl->suspend_sleep;
|
||||
else
|
||||
field = regl->sleep;
|
||||
|
||||
ret = regmap_field_read(field, &val);
|
||||
ret = regmap_field_read(regl->sleep, &val);
|
||||
if (ret < 0)
|
||||
return 0;
|
||||
|
||||
|
@ -475,42 +453,36 @@ static const struct da9063_regulator_info da9063_regulator_info[] = {
|
|||
da9063_buck_a_limits,
|
||||
DA9063_REG_BUCK_ILIM_C, DA9063_BCORE1_ILIM_MASK),
|
||||
DA9063_BUCK_COMMON_FIELDS(BCORE1),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE1_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BCORE2, 300, 10, 1570,
|
||||
da9063_buck_a_limits,
|
||||
DA9063_REG_BUCK_ILIM_C, DA9063_BCORE2_ILIM_MASK),
|
||||
DA9063_BUCK_COMMON_FIELDS(BCORE2),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE2_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BPRO, 530, 10, 1800,
|
||||
da9063_buck_a_limits,
|
||||
DA9063_REG_BUCK_ILIM_B, DA9063_BPRO_ILIM_MASK),
|
||||
DA9063_BUCK_COMMON_FIELDS(BPRO),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBPRO_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BMEM, 800, 20, 3340,
|
||||
da9063_buck_b_limits,
|
||||
DA9063_REG_BUCK_ILIM_A, DA9063_BMEM_ILIM_MASK),
|
||||
DA9063_BUCK_COMMON_FIELDS(BMEM),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBMEM_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BIO, 800, 20, 3340,
|
||||
da9063_buck_b_limits,
|
||||
DA9063_REG_BUCK_ILIM_A, DA9063_BIO_ILIM_MASK),
|
||||
DA9063_BUCK_COMMON_FIELDS(BIO),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_2, DA9063_VBIO_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BPERI, 800, 20, 3340,
|
||||
da9063_buck_b_limits,
|
||||
DA9063_REG_BUCK_ILIM_B, DA9063_BPERI_ILIM_MASK),
|
||||
DA9063_BUCK_COMMON_FIELDS(BPERI),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBPERI_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BCORES_MERGED, 300, 10, 1570,
|
||||
|
@ -518,7 +490,6 @@ static const struct da9063_regulator_info da9063_regulator_info[] = {
|
|||
DA9063_REG_BUCK_ILIM_C, DA9063_BCORE1_ILIM_MASK),
|
||||
/* BCORES_MERGED uses the same register fields as BCORE1 */
|
||||
DA9063_BUCK_COMMON_FIELDS(BCORE1),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBCORE1_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_BUCK(DA9063, BMEM_BIO_MERGED, 800, 20, 3340,
|
||||
|
@ -526,21 +497,17 @@ static const struct da9063_regulator_info da9063_regulator_info[] = {
|
|||
DA9063_REG_BUCK_ILIM_A, DA9063_BMEM_ILIM_MASK),
|
||||
/* BMEM_BIO_MERGED uses the same register fields as BMEM */
|
||||
DA9063_BUCK_COMMON_FIELDS(BMEM),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VBMEM_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO3, 900, 20, 3440),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO3_SEL),
|
||||
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO3_LIM),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO7, 900, 50, 3600),
|
||||
.suspend = BFIELD(DA9063_REG_LDO7_CONT, DA9063_VLDO7_SEL),
|
||||
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO7_LIM),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO8, 900, 50, 3600),
|
||||
.suspend = BFIELD(DA9063_REG_LDO8_CONT, DA9063_VLDO8_SEL),
|
||||
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO8_LIM),
|
||||
},
|
||||
{
|
||||
|
@ -549,36 +516,29 @@ static const struct da9063_regulator_info da9063_regulator_info[] = {
|
|||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO11, 900, 50, 3600),
|
||||
.suspend = BFIELD(DA9063_REG_LDO11_CONT, DA9063_VLDO11_SEL),
|
||||
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO11_LIM),
|
||||
},
|
||||
|
||||
/* The following LDOs are present only on DA9063, not on DA9063L */
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO1, 600, 20, 1860),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO1_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO2, 600, 20, 1860),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_1, DA9063_VLDO2_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO4, 900, 20, 3440),
|
||||
.suspend = BFIELD(DA9063_REG_DVC_2, DA9063_VLDO4_SEL),
|
||||
.oc_event = BFIELD(DA9063_REG_STATUS_D, DA9063_LDO4_LIM),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO5, 900, 50, 3600),
|
||||
.suspend = BFIELD(DA9063_REG_LDO5_CONT, DA9063_VLDO5_SEL),
|
||||
},
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO6, 900, 50, 3600),
|
||||
.suspend = BFIELD(DA9063_REG_LDO6_CONT, DA9063_VLDO6_SEL),
|
||||
},
|
||||
|
||||
{
|
||||
DA9063_LDO(DA9063, LDO10, 900, 50, 3600),
|
||||
.suspend = BFIELD(DA9063_REG_LDO10_CONT, DA9063_VLDO10_SEL),
|
||||
},
|
||||
};
|
||||
|
||||
|
|
290
drivers/regulator/mp886x.c
Normal file
290
drivers/regulator/mp886x.c
Normal file
|
@ -0,0 +1,290 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
//
|
||||
// MP8867/MP8869 regulator driver
|
||||
//
|
||||
// Copyright (C) 2020 Synaptics Incorporated
|
||||
//
|
||||
// Author: Jisheng Zhang <jszhang@kernel.org>
|
||||
|
||||
#include <linux/gpio/consumer.h>
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of_device.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/regulator/driver.h>
|
||||
#include <linux/regulator/of_regulator.h>
|
||||
|
||||
#define MP886X_VSEL 0x00
|
||||
#define MP886X_V_BOOT (1 << 7)
|
||||
#define MP886X_SYSCNTLREG1 0x01
|
||||
#define MP886X_MODE (1 << 0)
|
||||
#define MP886X_GO (1 << 6)
|
||||
#define MP886X_EN (1 << 7)
|
||||
|
||||
struct mp886x_device_info {
|
||||
struct device *dev;
|
||||
struct regulator_desc desc;
|
||||
struct regulator_init_data *regulator;
|
||||
struct gpio_desc *en_gpio;
|
||||
u32 r[2];
|
||||
unsigned int sel;
|
||||
};
|
||||
|
||||
static int mp886x_set_mode(struct regulator_dev *rdev, unsigned int mode)
|
||||
{
|
||||
switch (mode) {
|
||||
case REGULATOR_MODE_FAST:
|
||||
regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
|
||||
MP886X_MODE, MP886X_MODE);
|
||||
break;
|
||||
case REGULATOR_MODE_NORMAL:
|
||||
regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
|
||||
MP886X_MODE, 0);
|
||||
break;
|
||||
default:
|
||||
return -EINVAL;
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
static unsigned int mp886x_get_mode(struct regulator_dev *rdev)
|
||||
{
|
||||
u32 val;
|
||||
int ret;
|
||||
|
||||
ret = regmap_read(rdev->regmap, MP886X_SYSCNTLREG1, &val);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
if (val & MP886X_MODE)
|
||||
return REGULATOR_MODE_FAST;
|
||||
else
|
||||
return REGULATOR_MODE_NORMAL;
|
||||
}
|
||||
|
||||
static int mp8869_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
|
||||
{
|
||||
int ret;
|
||||
|
||||
ret = regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
|
||||
MP886X_GO, MP886X_GO);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
sel <<= ffs(rdev->desc->vsel_mask) - 1;
|
||||
return regmap_update_bits(rdev->regmap, rdev->desc->vsel_reg,
|
||||
MP886X_V_BOOT | rdev->desc->vsel_mask, sel);
|
||||
}
|
||||
|
||||
static inline unsigned int mp8869_scale(unsigned int uv, u32 r1, u32 r2)
|
||||
{
|
||||
u32 tmp = uv * r1 / r2;
|
||||
|
||||
return uv + tmp;
|
||||
}
|
||||
|
||||
static int mp8869_get_voltage_sel(struct regulator_dev *rdev)
|
||||
{
|
||||
struct mp886x_device_info *di = rdev_get_drvdata(rdev);
|
||||
int ret, uv;
|
||||
unsigned int val;
|
||||
bool fbloop;
|
||||
|
||||
ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
fbloop = val & MP886X_V_BOOT;
|
||||
if (fbloop) {
|
||||
uv = rdev->desc->min_uV;
|
||||
uv = mp8869_scale(uv, di->r[0], di->r[1]);
|
||||
return regulator_map_voltage_linear(rdev, uv, uv);
|
||||
}
|
||||
|
||||
val &= rdev->desc->vsel_mask;
|
||||
val >>= ffs(rdev->desc->vsel_mask) - 1;
|
||||
|
||||
return val;
|
||||
}
|
||||
|
||||
static const struct regulator_ops mp8869_regulator_ops = {
|
||||
.set_voltage_sel = mp8869_set_voltage_sel,
|
||||
.get_voltage_sel = mp8869_get_voltage_sel,
|
||||
.set_voltage_time_sel = regulator_set_voltage_time_sel,
|
||||
.map_voltage = regulator_map_voltage_linear,
|
||||
.list_voltage = regulator_list_voltage_linear,
|
||||
.enable = regulator_enable_regmap,
|
||||
.disable = regulator_disable_regmap,
|
||||
.is_enabled = regulator_is_enabled_regmap,
|
||||
.set_mode = mp886x_set_mode,
|
||||
.get_mode = mp886x_get_mode,
|
||||
};
|
||||
|
||||
static int mp8867_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
|
||||
{
|
||||
struct mp886x_device_info *di = rdev_get_drvdata(rdev);
|
||||
int ret, delta;
|
||||
|
||||
ret = mp8869_set_voltage_sel(rdev, sel);
|
||||
if (ret < 0)
|
||||
return ret;
|
||||
|
||||
delta = di->sel - sel;
|
||||
if (abs(delta) <= 5)
|
||||
ret = regmap_update_bits(rdev->regmap, MP886X_SYSCNTLREG1,
|
||||
MP886X_GO, 0);
|
||||
di->sel = sel;
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int mp8867_get_voltage_sel(struct regulator_dev *rdev)
|
||||
{
|
||||
struct mp886x_device_info *di = rdev_get_drvdata(rdev);
|
||||
int ret, uv;
|
||||
unsigned int val;
|
||||
bool fbloop;
|
||||
|
||||
ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
fbloop = val & MP886X_V_BOOT;
|
||||
|
||||
val &= rdev->desc->vsel_mask;
|
||||
val >>= ffs(rdev->desc->vsel_mask) - 1;
|
||||
|
||||
if (fbloop) {
|
||||
uv = regulator_list_voltage_linear(rdev, val);
|
||||
uv = mp8869_scale(uv, di->r[0], di->r[1]);
|
||||
return regulator_map_voltage_linear(rdev, uv, uv);
|
||||
}
|
||||
|
||||
return val;
|
||||
}
|
||||
|
||||
static const struct regulator_ops mp8867_regulator_ops = {
|
||||
.set_voltage_sel = mp8867_set_voltage_sel,
|
||||
.get_voltage_sel = mp8867_get_voltage_sel,
|
||||
.set_voltage_time_sel = regulator_set_voltage_time_sel,
|
||||
.map_voltage = regulator_map_voltage_linear,
|
||||
.list_voltage = regulator_list_voltage_linear,
|
||||
.enable = regulator_enable_regmap,
|
||||
.disable = regulator_disable_regmap,
|
||||
.is_enabled = regulator_is_enabled_regmap,
|
||||
.set_mode = mp886x_set_mode,
|
||||
.get_mode = mp886x_get_mode,
|
||||
};
|
||||
|
||||
static int mp886x_regulator_register(struct mp886x_device_info *di,
|
||||
struct regulator_config *config)
|
||||
{
|
||||
struct regulator_desc *rdesc = &di->desc;
|
||||
struct regulator_dev *rdev;
|
||||
|
||||
rdesc->name = "mp886x-reg";
|
||||
rdesc->supply_name = "vin";
|
||||
rdesc->ops = of_device_get_match_data(di->dev);
|
||||
rdesc->type = REGULATOR_VOLTAGE;
|
||||
rdesc->n_voltages = 128;
|
||||
rdesc->enable_reg = MP886X_SYSCNTLREG1;
|
||||
rdesc->enable_mask = MP886X_EN;
|
||||
rdesc->min_uV = 600000;
|
||||
rdesc->uV_step = 10000;
|
||||
rdesc->vsel_reg = MP886X_VSEL;
|
||||
rdesc->vsel_mask = 0x3f;
|
||||
rdesc->owner = THIS_MODULE;
|
||||
|
||||
rdev = devm_regulator_register(di->dev, &di->desc, config);
|
||||
if (IS_ERR(rdev))
|
||||
return PTR_ERR(rdev);
|
||||
di->sel = rdesc->ops->get_voltage_sel(rdev);
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct regmap_config mp886x_regmap_config = {
|
||||
.reg_bits = 8,
|
||||
.val_bits = 8,
|
||||
};
|
||||
|
||||
static int mp886x_i2c_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
struct device *dev = &client->dev;
|
||||
struct device_node *np = dev->of_node;
|
||||
struct mp886x_device_info *di;
|
||||
struct regulator_config config = { };
|
||||
struct regmap *regmap;
|
||||
int ret;
|
||||
|
||||
di = devm_kzalloc(dev, sizeof(struct mp886x_device_info), GFP_KERNEL);
|
||||
if (!di)
|
||||
return -ENOMEM;
|
||||
|
||||
di->regulator = of_get_regulator_init_data(dev, np, &di->desc);
|
||||
if (!di->regulator) {
|
||||
dev_err(dev, "Platform data not found!\n");
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
ret = of_property_read_u32_array(np, "mps,fb-voltage-divider",
|
||||
di->r, 2);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
di->en_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_HIGH);
|
||||
if (IS_ERR(di->en_gpio))
|
||||
return PTR_ERR(di->en_gpio);
|
||||
|
||||
di->dev = dev;
|
||||
|
||||
regmap = devm_regmap_init_i2c(client, &mp886x_regmap_config);
|
||||
if (IS_ERR(regmap)) {
|
||||
dev_err(dev, "Failed to allocate regmap!\n");
|
||||
return PTR_ERR(regmap);
|
||||
}
|
||||
i2c_set_clientdata(client, di);
|
||||
|
||||
config.dev = di->dev;
|
||||
config.init_data = di->regulator;
|
||||
config.regmap = regmap;
|
||||
config.driver_data = di;
|
||||
config.of_node = np;
|
||||
|
||||
ret = mp886x_regulator_register(di, &config);
|
||||
if (ret < 0)
|
||||
dev_err(dev, "Failed to register regulator!\n");
|
||||
return ret;
|
||||
}
|
||||
|
||||
static const struct of_device_id mp886x_dt_ids[] = {
|
||||
{
|
||||
.compatible = "mps,mp8867",
|
||||
.data = &mp8867_regulator_ops
|
||||
},
|
||||
{
|
||||
.compatible = "mps,mp8869",
|
||||
.data = &mp8869_regulator_ops
|
||||
},
|
||||
{ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, mp886x_dt_ids);
|
||||
|
||||
static const struct i2c_device_id mp886x_id[] = {
|
||||
{ "mp886x", },
|
||||
{ },
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, mp886x_id);
|
||||
|
||||
static struct i2c_driver mp886x_regulator_driver = {
|
||||
.driver = {
|
||||
.name = "mp886x-regulator",
|
||||
.of_match_table = of_match_ptr(mp886x_dt_ids),
|
||||
},
|
||||
.probe = mp886x_i2c_probe,
|
||||
.id_table = mp886x_id,
|
||||
};
|
||||
module_i2c_driver(mp886x_regulator_driver);
|
||||
|
||||
MODULE_AUTHOR("Jisheng Zhang <jszhang@kernel.org>");
|
||||
MODULE_DESCRIPTION("MP886x regulator driver");
|
||||
MODULE_LICENSE("GPL v2");
|
|
@ -445,6 +445,44 @@ static const struct regulator_desc pm8994_lnldo = {
|
|||
.ops = &rpm_smps_ldo_ops_fixed,
|
||||
};
|
||||
|
||||
static const struct regulator_desc pmi8994_ftsmps = {
|
||||
.linear_ranges = (struct regulator_linear_range[]) {
|
||||
REGULATOR_LINEAR_RANGE(350000, 0, 199, 5000),
|
||||
REGULATOR_LINEAR_RANGE(700000, 200, 349, 10000),
|
||||
},
|
||||
.n_linear_ranges = 2,
|
||||
.n_voltages = 350,
|
||||
.ops = &rpm_smps_ldo_ops,
|
||||
};
|
||||
|
||||
static const struct regulator_desc pmi8994_hfsmps = {
|
||||
.linear_ranges = (struct regulator_linear_range[]) {
|
||||
REGULATOR_LINEAR_RANGE(350000, 0, 80, 12500),
|
||||
REGULATOR_LINEAR_RANGE(700000, 81, 141, 25000),
|
||||
},
|
||||
.n_linear_ranges = 2,
|
||||
.n_voltages = 142,
|
||||
.ops = &rpm_smps_ldo_ops,
|
||||
};
|
||||
|
||||
static const struct regulator_desc pmi8994_bby = {
|
||||
.linear_ranges = (struct regulator_linear_range[]) {
|
||||
REGULATOR_LINEAR_RANGE(3000000, 0, 44, 50000),
|
||||
},
|
||||
.n_linear_ranges = 1,
|
||||
.n_voltages = 45,
|
||||
.ops = &rpm_bob_ops,
|
||||
};
|
||||
|
||||
static const struct regulator_desc pmi8994_boost = {
|
||||
.linear_ranges = (struct regulator_linear_range[]) {
|
||||
REGULATOR_LINEAR_RANGE(4000000, 0, 30, 50000),
|
||||
},
|
||||
.n_linear_ranges = 1,
|
||||
.n_voltages = 31,
|
||||
.ops = &rpm_smps_ldo_ops,
|
||||
};
|
||||
|
||||
static const struct regulator_desc pm8998_ftsmps = {
|
||||
.linear_ranges = (struct regulator_linear_range[]) {
|
||||
REGULATOR_LINEAR_RANGE(320000, 0, 258, 4000),
|
||||
|
@ -780,6 +818,14 @@ static const struct rpm_regulator_data rpm_pm8994_regulators[] = {
|
|||
{}
|
||||
};
|
||||
|
||||
static const struct rpm_regulator_data rpm_pmi8994_regulators[] = {
|
||||
{ "s1", QCOM_SMD_RPM_SMPB, 1, &pmi8994_ftsmps, "vdd_s1" },
|
||||
{ "s2", QCOM_SMD_RPM_SMPB, 2, &pmi8994_hfsmps, "vdd_s2" },
|
||||
{ "s2", QCOM_SMD_RPM_SMPB, 3, &pmi8994_hfsmps, "vdd_s3" },
|
||||
{ "boost-bypass", QCOM_SMD_RPM_BBYB, 1, &pmi8994_bby, "vdd_bst_byp" },
|
||||
{}
|
||||
};
|
||||
|
||||
static const struct rpm_regulator_data rpm_pm8998_regulators[] = {
|
||||
{ "s1", QCOM_SMD_RPM_SMPA, 1, &pm8998_ftsmps, "vdd_s1" },
|
||||
{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8998_ftsmps, "vdd_s2" },
|
||||
|
@ -862,6 +908,7 @@ static const struct of_device_id rpm_of_match[] = {
|
|||
{ .compatible = "qcom,rpm-pm8994-regulators", .data = &rpm_pm8994_regulators },
|
||||
{ .compatible = "qcom,rpm-pm8998-regulators", .data = &rpm_pm8998_regulators },
|
||||
{ .compatible = "qcom,rpm-pma8084-regulators", .data = &rpm_pma8084_regulators },
|
||||
{ .compatible = "qcom,rpm-pmi8994-regulators", .data = &rpm_pmi8994_regulators },
|
||||
{ .compatible = "qcom,rpm-pmi8998-regulators", .data = &rpm_pmi8998_regulators },
|
||||
{ .compatible = "qcom,rpm-pms405-regulators", .data = &rpm_pms405_regulators },
|
||||
{}
|
||||
|
|
|
@ -277,9 +277,9 @@ enum regulator_type {
|
|||
* @curr_table: Current limit mapping table (if table based mapping)
|
||||
*
|
||||
* @vsel_range_reg: Register for range selector when using pickable ranges
|
||||
* and regulator_regmap_X_voltage_X_pickable functions.
|
||||
* and ``regulator_map_*_voltage_*_pickable`` functions.
|
||||
* @vsel_range_mask: Mask for register bitfield used for range selector
|
||||
* @vsel_reg: Register for selector when using regulator_regmap_X_voltage_
|
||||
* @vsel_reg: Register for selector when using ``regulator_map_*_voltage_*``
|
||||
* @vsel_mask: Mask for register bitfield used for selector
|
||||
* @vsel_step: Specify the resolution of selector stepping when setting
|
||||
* voltage. If 0, then no stepping is done (requested selector is
|
||||
|
|
|
@ -10,6 +10,7 @@ struct qcom_smd_rpm;
|
|||
/*
|
||||
* Constants used for addressing resources in the RPM.
|
||||
*/
|
||||
#define QCOM_SMD_RPM_BBYB 0x62796262
|
||||
#define QCOM_SMD_RPM_BOBB 0x62626f62
|
||||
#define QCOM_SMD_RPM_BOOST 0x61747362
|
||||
#define QCOM_SMD_RPM_BUS_CLK 0x316b6c63
|
||||
|
|
Loading…
Reference in a new issue