diff --git a/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt new file mode 100644 index 000000000000..6069b95a883d --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-lantiq-ssc.txt @@ -0,0 +1,29 @@ +Lantiq Synchronous Serial Controller (SSC) SPI master driver + +Required properties: +- compatible: "lantiq,ase-spi", "lantiq,falcon-spi", "lantiq,xrx100-spi" +- #address-cells: see spi-bus.txt +- #size-cells: see spi-bus.txt +- reg: address and length of the spi master registers +- interrupts: should contain the "spi_rx", "spi_tx" and "spi_err" interrupt. + + +Optional properties: +- clocks: spi clock phandle +- num-cs: see spi-bus.txt, set to 8 if unset +- base-cs: the number of the first chip select, set to 1 if unset. + +Example: + + +spi: spi@E100800 { + compatible = "lantiq,xrx200-spi", "lantiq,xrx100-spi"; + reg = <0xE100800 0x100>; + interrupt-parent = <&icu0>; + interrupts = <22 23 24>; + interrupt-names = "spi_rx", "spi_tx", "spi_err"; + #address-cells = <1>; + #size-cells = <1>; + num-cs = <6>; + base-cs = <1>; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index d2ca153614f9..83da4931d832 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -31,6 +31,10 @@ Optional Properties: - rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling Rx data (may need to be fine tuned for high capacitance lines). No delay (0) by default. +- pinctrl-names: Names for the pin configuration(s); may be "default" or + "sleep", where the "sleep" configuration may describe the state + the pins should be in during system suspend. See also + pinctrl/pinctrl-bindings.txt. Example: @@ -46,4 +50,7 @@ Example: interrupts = ; clocks = <&cru SCLK_SPI0>, <&cru PCLK_SPI0>; clock-names = "spiclk", "apb_pclk"; + pinctrl-0 = <&spi1_pins>; + pinctrl-1 = <&spi1_sleep>; + pinctrl-names = "default", "sleep"; }; diff --git a/Documentation/spi/ep93xx_spi b/Documentation/spi/ep93xx_spi deleted file mode 100644 index 832ddce6e5fb..000000000000 --- a/Documentation/spi/ep93xx_spi +++ /dev/null @@ -1,105 +0,0 @@ -Cirrus EP93xx SPI controller driver HOWTO -========================================= - -ep93xx_spi driver brings SPI master support for EP93xx SPI controller. Chip -selects are implemented with GPIO lines. - -NOTE: If possible, don't use SFRMOUT (SFRM1) signal as a chip select. It will -not work correctly (it cannot be controlled by software). Use GPIO lines -instead. - -Sample configuration -==================== - -Typically driver configuration is done in platform board files (the files under -arch/arm/mach-ep93xx/*.c). In this example we configure MMC over SPI through -this driver on TS-7260 board. You can adapt the code to suit your needs. - -This example uses EGPIO9 as SD/MMC card chip select (this is wired in DIO1 -header on the board). - -You need to select CONFIG_MMC_SPI to use mmc_spi driver. - -arch/arm/mach-ep93xx/ts72xx.c: - -... -#include -#include - -#include - -/* this is our GPIO line used for chip select */ -#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO9 - -static int ts72xx_mmc_spi_setup(struct spi_device *spi) -{ - int err; - - err = gpio_request(MMC_CHIP_SELECT_GPIO, spi->modalias); - if (err) - return err; - - gpio_direction_output(MMC_CHIP_SELECT_GPIO, 1); - - return 0; -} - -static void ts72xx_mmc_spi_cleanup(struct spi_device *spi) -{ - gpio_set_value(MMC_CHIP_SELECT_GPIO, 1); - gpio_direction_input(MMC_CHIP_SELECT_GPIO); - gpio_free(MMC_CHIP_SELECT_GPIO); -} - -static void ts72xx_mmc_spi_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(MMC_CHIP_SELECT_GPIO, value); -} - -static struct ep93xx_spi_chip_ops ts72xx_mmc_spi_ops = { - .setup = ts72xx_mmc_spi_setup, - .cleanup = ts72xx_mmc_spi_cleanup, - .cs_control = ts72xx_mmc_spi_cs_control, -}; - -static struct spi_board_info ts72xx_spi_devices[] __initdata = { - { - .modalias = "mmc_spi", - .controller_data = &ts72xx_mmc_spi_ops, - /* - * We use 10 MHz even though the maximum is 7.4 MHz. The driver - * will limit it automatically to max. frequency. - */ - .max_speed_hz = 10 * 1000 * 1000, - .bus_num = 0, - .chip_select = 0, - .mode = SPI_MODE_0, - }, -}; - -static struct ep93xx_spi_info ts72xx_spi_info = { - .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices), -}; - -static void __init ts72xx_init_machine(void) -{ - ... - ep93xx_register_spi(&ts72xx_spi_info, ts72xx_spi_devices, - ARRAY_SIZE(ts72xx_spi_devices)); -} - -The driver can use DMA for the transfers also. In this case ts72xx_spi_info -becomes: - -static struct ep93xx_spi_info ts72xx_spi_info = { - .num_chipselect = ARRAY_SIZE(ts72xx_spi_devices), - .use_dma = true; -}; - -Note that CONFIG_EP93XX_DMA should be enabled as well. - -Thanks to -========= -Martin Guy, H. Hartley Sweeten and others who helped me during development of -the driver. Simplemachines.it donated me a Sim.One board which I used testing -the driver on EP9307. diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c index ad92d9f7e4df..0ac176386789 100644 --- a/arch/arm/mach-ep93xx/edb93xx.c +++ b/arch/arm/mach-ep93xx/edb93xx.c @@ -27,7 +27,6 @@ #include #include #include -#include #include #include #include @@ -106,33 +105,10 @@ static struct cs4271_platform_data edb93xx_cs4271_data = { .gpio_nreset = -EINVAL, /* filled in later */ }; -static int edb93xx_cs4271_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6, - GPIOF_OUT_INIT_HIGH, spi->modalias); -} - -static void edb93xx_cs4271_hw_cleanup(struct spi_device *spi) -{ - gpio_free(EP93XX_GPIO_LINE_EGPIO6); -} - -static void edb93xx_cs4271_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value); -} - -static struct ep93xx_spi_chip_ops edb93xx_cs4271_hw = { - .setup = edb93xx_cs4271_hw_setup, - .cleanup = edb93xx_cs4271_hw_cleanup, - .cs_control = edb93xx_cs4271_hw_cs_control, -}; - static struct spi_board_info edb93xx_spi_board_info[] __initdata = { { .modalias = "cs4271", .platform_data = &edb93xx_cs4271_data, - .controller_data = &edb93xx_cs4271_hw, .max_speed_hz = 6000000, .bus_num = 0, .chip_select = 0, @@ -140,8 +116,13 @@ static struct spi_board_info edb93xx_spi_board_info[] __initdata = { }, }; +static int edb93xx_spi_chipselects[] __initdata = { + EP93XX_GPIO_LINE_EGPIO6, +}; + static struct ep93xx_spi_info edb93xx_spi_info __initdata = { - .num_chipselect = ARRAY_SIZE(edb93xx_spi_board_info), + .chipselect = edb93xx_spi_chipselects, + .num_chipselect = ARRAY_SIZE(edb93xx_spi_chipselects), }; static void __init edb93xx_register_spi(void) diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c index 7bb540c421ee..c7a40f245892 100644 --- a/arch/arm/mach-ep93xx/simone.c +++ b/arch/arm/mach-ep93xx/simone.c @@ -48,56 +48,6 @@ static struct ep93xxfb_mach_info __initdata simone_fb_info = { */ #define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0 -/* - * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes - * low between multi-message command blocks. From v1.4, it uses a GPIO instead. - * v1.3 parts will still work, since the signal on SFRMOUT is automatic. - */ -#define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO1 - -/* - * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal, - * you can leave these empty and pass NULL as .controller_data. - */ - -static int simone_mmc_spi_setup(struct spi_device *spi) -{ - unsigned int gpio = MMC_CHIP_SELECT_GPIO; - int err; - - err = gpio_request(gpio, spi->modalias); - if (err) - return err; - - err = gpio_direction_output(gpio, 1); - if (err) { - gpio_free(gpio); - return err; - } - - return 0; -} - -static void simone_mmc_spi_cleanup(struct spi_device *spi) -{ - unsigned int gpio = MMC_CHIP_SELECT_GPIO; - - gpio_set_value(gpio, 1); - gpio_direction_input(gpio); - gpio_free(gpio); -} - -static void simone_mmc_spi_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(MMC_CHIP_SELECT_GPIO, value); -} - -static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = { - .setup = simone_mmc_spi_setup, - .cleanup = simone_mmc_spi_cleanup, - .cs_control = simone_mmc_spi_cs_control, -}; - /* * MMC card detection GPIO setup. */ @@ -152,7 +102,6 @@ static struct mmc_spi_platform_data simone_mmc_spi_data = { static struct spi_board_info simone_spi_devices[] __initdata = { { .modalias = "mmc_spi", - .controller_data = &simone_mmc_spi_ops, .platform_data = &simone_mmc_spi_data, /* * We use 10 MHz even though the maximum is 3.7 MHz. The driver @@ -165,8 +114,18 @@ static struct spi_board_info simone_spi_devices[] __initdata = { }, }; +/* + * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes + * low between multi-message command blocks. From v1.4, it uses a GPIO instead. + * v1.3 parts will still work, since the signal on SFRMOUT is automatic. + */ +static int simone_spi_chipselects[] __initdata = { + EP93XX_GPIO_LINE_EGPIO1, +}; + static struct ep93xx_spi_info simone_spi_info __initdata = { - .num_chipselect = ARRAY_SIZE(simone_spi_devices), + .chipselect = simone_spi_chipselects, + .num_chipselect = ARRAY_SIZE(simone_spi_chipselects), .use_dma = 1, }; diff --git a/arch/arm/mach-ep93xx/vision_ep9307.c b/arch/arm/mach-ep93xx/vision_ep9307.c index 5cced5988498..1daf9441058c 100644 --- a/arch/arm/mach-ep93xx/vision_ep9307.c +++ b/arch/arm/mach-ep93xx/vision_ep9307.c @@ -175,33 +175,9 @@ static struct cs4271_platform_data vision_cs4271_data = { .gpio_nreset = EP93XX_GPIO_LINE_H(2), }; -static int vision_cs4271_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6, - GPIOF_OUT_INIT_HIGH, spi->modalias); -} - -static void vision_cs4271_hw_cleanup(struct spi_device *spi) -{ - gpio_free(EP93XX_GPIO_LINE_EGPIO6); -} - -static void vision_cs4271_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value); -} - -static struct ep93xx_spi_chip_ops vision_cs4271_hw = { - .setup = vision_cs4271_hw_setup, - .cleanup = vision_cs4271_hw_cleanup, - .cs_control = vision_cs4271_hw_cs_control, -}; - /************************************************************************* * SPI Flash *************************************************************************/ -#define VISION_SPI_FLASH_CS EP93XX_GPIO_LINE_EGPIO7 - static struct mtd_partition vision_spi_flash_partitions[] = { { .name = "SPI bootstrap", @@ -224,68 +200,20 @@ static struct flash_platform_data vision_spi_flash_data = { .nr_parts = ARRAY_SIZE(vision_spi_flash_partitions), }; -static int vision_spi_flash_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(VISION_SPI_FLASH_CS, GPIOF_INIT_HIGH, - spi->modalias); -} - -static void vision_spi_flash_hw_cleanup(struct spi_device *spi) -{ - gpio_free(VISION_SPI_FLASH_CS); -} - -static void vision_spi_flash_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(VISION_SPI_FLASH_CS, value); -} - -static struct ep93xx_spi_chip_ops vision_spi_flash_hw = { - .setup = vision_spi_flash_hw_setup, - .cleanup = vision_spi_flash_hw_cleanup, - .cs_control = vision_spi_flash_hw_cs_control, -}; - /************************************************************************* * SPI SD/MMC host *************************************************************************/ -#define VISION_SPI_MMC_CS EP93XX_GPIO_LINE_G(2) -#define VISION_SPI_MMC_WP EP93XX_GPIO_LINE_F(0) -#define VISION_SPI_MMC_CD EP93XX_GPIO_LINE_EGPIO15 - static struct mmc_spi_platform_data vision_spi_mmc_data = { .detect_delay = 100, .powerup_msecs = 100, .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, .flags = MMC_SPI_USE_CD_GPIO | MMC_SPI_USE_RO_GPIO, - .cd_gpio = VISION_SPI_MMC_CD, + .cd_gpio = EP93XX_GPIO_LINE_EGPIO15, .cd_debounce = 1, - .ro_gpio = VISION_SPI_MMC_WP, + .ro_gpio = EP93XX_GPIO_LINE_F(0), .caps2 = MMC_CAP2_RO_ACTIVE_HIGH, }; -static int vision_spi_mmc_hw_setup(struct spi_device *spi) -{ - return gpio_request_one(VISION_SPI_MMC_CS, GPIOF_INIT_HIGH, - spi->modalias); -} - -static void vision_spi_mmc_hw_cleanup(struct spi_device *spi) -{ - gpio_free(VISION_SPI_MMC_CS); -} - -static void vision_spi_mmc_hw_cs_control(struct spi_device *spi, int value) -{ - gpio_set_value(VISION_SPI_MMC_CS, value); -} - -static struct ep93xx_spi_chip_ops vision_spi_mmc_hw = { - .setup = vision_spi_mmc_hw_setup, - .cleanup = vision_spi_mmc_hw_cleanup, - .cs_control = vision_spi_mmc_hw_cs_control, -}; - /************************************************************************* * SPI Bus *************************************************************************/ @@ -293,7 +221,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { { .modalias = "cs4271", .platform_data = &vision_cs4271_data, - .controller_data = &vision_cs4271_hw, .max_speed_hz = 6000000, .bus_num = 0, .chip_select = 0, @@ -301,7 +228,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, { .modalias = "sst25l", .platform_data = &vision_spi_flash_data, - .controller_data = &vision_spi_flash_hw, .max_speed_hz = 20000000, .bus_num = 0, .chip_select = 1, @@ -309,7 +235,6 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, { .modalias = "mmc_spi", .platform_data = &vision_spi_mmc_data, - .controller_data = &vision_spi_mmc_hw, .max_speed_hz = 20000000, .bus_num = 0, .chip_select = 2, @@ -317,8 +242,15 @@ static struct spi_board_info vision_spi_board_info[] __initdata = { }, }; +static int vision_spi_chipselects[] __initdata = { + EP93XX_GPIO_LINE_EGPIO6, + EP93XX_GPIO_LINE_EGPIO7, + EP93XX_GPIO_LINE_G(2), +}; + static struct ep93xx_spi_info vision_spi_master __initdata = { - .num_chipselect = ARRAY_SIZE(vision_spi_board_info), + .chipselect = vision_spi_chipselects, + .num_chipselect = ARRAY_SIZE(vision_spi_chipselects), .use_dma = 1, }; diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 2922a9908302..25ae7f2e44b5 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -162,7 +162,8 @@ config SPI_BCM63XX_HSSPI config SPI_BCM_QSPI tristate "Broadcom BSPI and MSPI controller support" - depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST + depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \ + BMIPS_GENERIC || COMPILE_TEST default ARCH_BCM_IPROC help Enables support for the Broadcom SPI flash and MSPI controller. @@ -263,7 +264,7 @@ config SPI_EP93XX mode. config SPI_FALCON - tristate "Falcon SPI controller support" + bool "Falcon SPI controller support" depends on SOC_FALCON help The external bus unit (EBU) found on the FALC-ON SoC has SPI @@ -416,6 +417,14 @@ config SPI_NUC900 help SPI driver for Nuvoton NUC900 series ARM SoCs +config SPI_LANTIQ_SSC + tristate "Lantiq SSC SPI controller" + depends on LANTIQ || COMPILE_TEST + help + This driver supports the Lantiq SSC SPI controller in master + mode. This controller is found on Intel (former Lantiq) SoCs like + the Danube, Falcon, xRX200, xRX300. + config SPI_OC_TINY tristate "OpenCores tiny SPI" depends on GPIOLIB || COMPILE_TEST diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 7a6b64662c82..b375a7a89216 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -49,6 +49,7 @@ obj-$(CONFIG_SPI_FSL_SPI) += spi-fsl-spi.o obj-$(CONFIG_SPI_GPIO) += spi-gpio.o obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o obj-$(CONFIG_SPI_IMX) += spi-imx.o +obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o obj-$(CONFIG_SPI_JCORE) += spi-jcore.o obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c index 0314c6b9e044..6c7d7a460689 100644 --- a/drivers/spi/spi-armada-3700.c +++ b/drivers/spi/spi-armada-3700.c @@ -170,12 +170,12 @@ static int a3700_spi_pin_mode_set(struct a3700_spi *a3700_spi, val &= ~(A3700_SPI_DATA_PIN0 | A3700_SPI_DATA_PIN1); switch (pin_mode) { - case 1: + case SPI_NBITS_SINGLE: break; - case 2: + case SPI_NBITS_DUAL: val |= A3700_SPI_DATA_PIN0; break; - case 4: + case SPI_NBITS_QUAD: val |= A3700_SPI_DATA_PIN1; break; default: @@ -340,8 +340,7 @@ static irqreturn_t a3700_spi_interrupt(int irq, void *dev_id) spireg_write(a3700_spi, A3700_SPI_INT_STAT_REG, cause); /* Wake up the transfer */ - if (a3700_spi->wait_mask & cause) - complete(&a3700_spi->done); + complete(&a3700_spi->done); return IRQ_HANDLED; } @@ -421,7 +420,7 @@ static void a3700_spi_fifo_thres_set(struct a3700_spi *a3700_spi, } static void a3700_spi_transfer_setup(struct spi_device *spi, - struct spi_transfer *xfer) + struct spi_transfer *xfer) { struct a3700_spi *a3700_spi; unsigned int byte_len; @@ -562,6 +561,7 @@ static int a3700_spi_fifo_read(struct a3700_spi *a3700_spi) val = spireg_read(a3700_spi, A3700_SPI_DATA_IN_REG); if (a3700_spi->buf_len >= 4) { u32 data = le32_to_cpu(val); + memcpy(a3700_spi->rx_buf, &data, 4); a3700_spi->buf_len -= 4; @@ -901,7 +901,6 @@ static int a3700_spi_remove(struct platform_device *pdev) struct a3700_spi *spi = spi_master_get_devdata(master); clk_unprepare(spi->clk); - spi_master_put(master); return 0; } @@ -909,7 +908,6 @@ static int a3700_spi_remove(struct platform_device *pdev) static struct platform_driver a3700_spi_driver = { .driver = { .name = DRIVER_NAME, - .owner = THIS_MODULE, .of_match_table = of_match_ptr(a3700_spi_dt_ids), }, .probe = a3700_spi_probe, diff --git a/drivers/spi/spi-ath79.c b/drivers/spi/spi-ath79.c index f369174fbd88..b89cee11f418 100644 --- a/drivers/spi/spi-ath79.c +++ b/drivers/spi/spi-ath79.c @@ -78,14 +78,16 @@ static void ath79_spi_chipselect(struct spi_device *spi, int is_active) ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base); } - if (spi->chip_select) { + if (gpio_is_valid(spi->cs_gpio)) { /* SPI is normally active-low */ - gpio_set_value(spi->cs_gpio, cs_high); + gpio_set_value_cansleep(spi->cs_gpio, cs_high); } else { + u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select); + if (cs_high) - sp->ioc_base |= AR71XX_SPI_IOC_CS0; + sp->ioc_base |= cs_bit; else - sp->ioc_base &= ~AR71XX_SPI_IOC_CS0; + sp->ioc_base &= ~cs_bit; ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base); } @@ -118,11 +120,8 @@ static int ath79_spi_setup_cs(struct spi_device *spi) struct ath79_spi *sp = ath79_spidev_to_sp(spi); int status; - if (spi->chip_select && !gpio_is_valid(spi->cs_gpio)) - return -EINVAL; - status = 0; - if (spi->chip_select) { + if (gpio_is_valid(spi->cs_gpio)) { unsigned long flags; flags = GPIOF_DIR_OUT; @@ -134,10 +133,12 @@ static int ath79_spi_setup_cs(struct spi_device *spi) status = gpio_request_one(spi->cs_gpio, flags, dev_name(&spi->dev)); } else { + u32 cs_bit = AR71XX_SPI_IOC_CS(spi->chip_select); + if (spi->mode & SPI_CS_HIGH) - sp->ioc_base &= ~AR71XX_SPI_IOC_CS0; + sp->ioc_base &= ~cs_bit; else - sp->ioc_base |= AR71XX_SPI_IOC_CS0; + sp->ioc_base |= cs_bit; ath79_spi_wr(sp, AR71XX_SPI_REG_IOC, sp->ioc_base); } @@ -147,7 +148,7 @@ static int ath79_spi_setup_cs(struct spi_device *spi) static void ath79_spi_cleanup_cs(struct spi_device *spi) { - if (spi->chip_select) { + if (gpio_is_valid(spi->cs_gpio)) { gpio_free(spi->cs_gpio); } } diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c index d7843fd8c610..b19722ba908c 100644 --- a/drivers/spi/spi-bcm-qspi.c +++ b/drivers/spi/spi-bcm-qspi.c @@ -89,7 +89,7 @@ #define BSPI_BPP_MODE_SELECT_MASK BIT(8) #define BSPI_BPP_ADDR_SELECT_MASK BIT(16) -#define BSPI_READ_LENGTH 256 +#define BSPI_READ_LENGTH 512 /* MSPI register offsets */ #define MSPI_SPCR0_LSB 0x000 @@ -192,9 +192,11 @@ struct bcm_qspi_dev_id { void *dev; }; + struct qspi_trans { struct spi_transfer *trans; int byte; + bool mspi_last_trans; }; struct bcm_qspi { @@ -616,6 +618,16 @@ static int bcm_qspi_setup(struct spi_device *spi) return 0; } +static bool bcm_qspi_mspi_transfer_is_last(struct bcm_qspi *qspi, + struct qspi_trans *qt) +{ + if (qt->mspi_last_trans && + spi_transfer_is_last(qspi->master, qt->trans)) + return true; + else + return false; +} + static int update_qspi_trans_byte_count(struct bcm_qspi *qspi, struct qspi_trans *qt, int flags) { @@ -629,7 +641,6 @@ static int update_qspi_trans_byte_count(struct bcm_qspi *qspi, if (qt->byte >= qt->trans->len) { /* we're at the end of the spi_transfer */ - /* in TX mode, need to pause for a delay or CS change */ if (qt->trans->delay_usecs && (flags & TRANS_STATUS_BREAK_DELAY)) @@ -641,7 +652,7 @@ static int update_qspi_trans_byte_count(struct bcm_qspi *qspi, goto done; dev_dbg(&qspi->pdev->dev, "advance msg exit\n"); - if (spi_transfer_is_last(qspi->master, qt->trans)) + if (bcm_qspi_mspi_transfer_is_last(qspi, qt)) ret = TRANS_STATUS_BREAK_EOM; else ret = TRANS_STATUS_BREAK_NO_BYTES; @@ -813,7 +824,7 @@ static int bcm_qspi_bspi_flash_read(struct spi_device *spi, struct spi_flash_read_message *msg) { struct bcm_qspi *qspi = spi_master_get_devdata(spi->master); - u32 addr = 0, len, len_words; + u32 addr = 0, len, rdlen, len_words; int ret = 0; unsigned long timeo = msecs_to_jiffies(100); struct bcm_qspi_soc_intc *soc_intc = qspi->soc_intc; @@ -826,7 +837,7 @@ static int bcm_qspi_bspi_flash_read(struct spi_device *spi, bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0); /* - * when using flex mode mode we need to send + * when using flex mode we need to send * the upper address byte to bspi */ if (bcm_qspi_bspi_ver_three(qspi) == false) { @@ -840,48 +851,127 @@ static int bcm_qspi_bspi_flash_read(struct spi_device *spi, else addr = msg->from & 0x00ffffff; - /* set BSPI RAF buffer max read length */ - len = msg->len; - if (len > BSPI_READ_LENGTH) - len = BSPI_READ_LENGTH; - if (bcm_qspi_bspi_ver_three(qspi) == true) addr = (addr + 0xc00000) & 0xffffff; - reinit_completion(&qspi->bspi_done); - bcm_qspi_enable_bspi(qspi); - len_words = (len + 3) >> 2; - qspi->bspi_rf_msg = msg; - qspi->bspi_rf_msg_status = 0; + /* + * read into the entire buffer by breaking the reads + * into RAF buffer read lengths + */ + len = msg->len; qspi->bspi_rf_msg_idx = 0; - qspi->bspi_rf_msg_len = len; - dev_dbg(&qspi->pdev->dev, "bspi xfr addr 0x%x len 0x%x", addr, len); - bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr); - bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words); - bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0); + do { + if (len > BSPI_READ_LENGTH) + rdlen = BSPI_READ_LENGTH; + else + rdlen = len; - if (qspi->soc_intc) { - /* - * clear soc MSPI and BSPI interrupts and enable - * BSPI interrupts. - */ - soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE); - soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true); + reinit_completion(&qspi->bspi_done); + bcm_qspi_enable_bspi(qspi); + len_words = (rdlen + 3) >> 2; + qspi->bspi_rf_msg = msg; + qspi->bspi_rf_msg_status = 0; + qspi->bspi_rf_msg_len = rdlen; + dev_dbg(&qspi->pdev->dev, + "bspi xfr addr 0x%x len 0x%x", addr, rdlen); + bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr); + bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words); + bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0); + if (qspi->soc_intc) { + /* + * clear soc MSPI and BSPI interrupts and enable + * BSPI interrupts. + */ + soc_intc->bcm_qspi_int_ack(soc_intc, MSPI_BSPI_DONE); + soc_intc->bcm_qspi_int_set(soc_intc, BSPI_DONE, true); + } + + /* Must flush previous writes before starting BSPI operation */ + mb(); + bcm_qspi_bspi_lr_start(qspi); + if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) { + dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n"); + ret = -ETIMEDOUT; + break; + } + + /* set msg return length */ + msg->retlen += rdlen; + addr += rdlen; + len -= rdlen; + } while (len); + + return ret; +} + +static int bcm_qspi_transfer_one(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *trans) +{ + struct bcm_qspi *qspi = spi_master_get_devdata(master); + int slots; + unsigned long timeo = msecs_to_jiffies(100); + + bcm_qspi_chip_select(qspi, spi->chip_select); + qspi->trans_pos.trans = trans; + qspi->trans_pos.byte = 0; + + while (qspi->trans_pos.byte < trans->len) { + reinit_completion(&qspi->mspi_done); + + slots = write_to_hw(qspi, spi); + if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) { + dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n"); + return -ETIMEDOUT; + } + + read_from_hw(qspi, slots); } - /* Must flush previous writes before starting BSPI operation */ - mb(); + return 0; +} - bcm_qspi_bspi_lr_start(qspi); - if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) { - dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n"); - ret = -ETIMEDOUT; - } else { - /* set the return length for the caller */ - msg->retlen = len; +static int bcm_qspi_mspi_flash_read(struct spi_device *spi, + struct spi_flash_read_message *msg) +{ + struct bcm_qspi *qspi = spi_master_get_devdata(spi->master); + struct spi_transfer t[2]; + u8 cmd[6]; + int ret; + + memset(cmd, 0, sizeof(cmd)); + memset(t, 0, sizeof(t)); + + /* tx */ + /* opcode is in cmd[0] */ + cmd[0] = msg->read_opcode; + cmd[1] = msg->from >> (msg->addr_width * 8 - 8); + cmd[2] = msg->from >> (msg->addr_width * 8 - 16); + cmd[3] = msg->from >> (msg->addr_width * 8 - 24); + cmd[4] = msg->from >> (msg->addr_width * 8 - 32); + t[0].tx_buf = cmd; + t[0].len = msg->addr_width + msg->dummy_bytes + 1; + t[0].bits_per_word = spi->bits_per_word; + t[0].tx_nbits = msg->opcode_nbits; + /* lets mspi know that this is not last transfer */ + qspi->trans_pos.mspi_last_trans = false; + ret = bcm_qspi_transfer_one(spi->master, spi, &t[0]); + + /* rx */ + qspi->trans_pos.mspi_last_trans = true; + if (!ret) { + /* rx */ + t[1].rx_buf = msg->buf; + t[1].len = msg->len; + t[1].rx_nbits = msg->data_nbits; + t[1].bits_per_word = spi->bits_per_word; + ret = bcm_qspi_transfer_one(spi->master, spi, &t[1]); } + if (!ret) + msg->retlen = msg->len; + return ret; } @@ -918,8 +1008,7 @@ static int bcm_qspi_flash_read(struct spi_device *spi, mspi_read = true; if (mspi_read) - /* this will make the m25p80 read to fallback to mspi read */ - return -EAGAIN; + return bcm_qspi_mspi_flash_read(spi, msg); io_width = msg->data_nbits ? msg->data_nbits : SPI_NBITS_SINGLE; addrlen = msg->addr_width; @@ -931,33 +1020,6 @@ static int bcm_qspi_flash_read(struct spi_device *spi, return ret; } -static int bcm_qspi_transfer_one(struct spi_master *master, - struct spi_device *spi, - struct spi_transfer *trans) -{ - struct bcm_qspi *qspi = spi_master_get_devdata(master); - int slots; - unsigned long timeo = msecs_to_jiffies(100); - - bcm_qspi_chip_select(qspi, spi->chip_select); - qspi->trans_pos.trans = trans; - qspi->trans_pos.byte = 0; - - while (qspi->trans_pos.byte < trans->len) { - reinit_completion(&qspi->mspi_done); - - slots = write_to_hw(qspi, spi); - if (!wait_for_completion_timeout(&qspi->mspi_done, timeo)) { - dev_err(&qspi->pdev->dev, "timeout waiting for MSPI\n"); - return -ETIMEDOUT; - } - - read_from_hw(qspi, slots); - } - - return 0; -} - static void bcm_qspi_cleanup(struct spi_device *spi) { struct bcm_qspi_parms *xp = spi_get_ctldata(spi); @@ -1187,6 +1249,7 @@ int bcm_qspi_probe(struct platform_device *pdev, qspi->pdev = pdev; qspi->trans_pos.trans = NULL; qspi->trans_pos.byte = 0; + qspi->trans_pos.mspi_last_trans = true; qspi->master = master; master->bus_num = -1; @@ -1345,7 +1408,6 @@ int bcm_qspi_remove(struct platform_device *pdev) { struct bcm_qspi *qspi = platform_get_drvdata(pdev); - platform_set_drvdata(pdev, NULL); bcm_qspi_hw_uninit(qspi); clk_disable_unprepare(qspi->clk); kfree(qspi->dev_ids); diff --git a/drivers/spi/spi-bcm53xx.c b/drivers/spi/spi-bcm53xx.c index afb51699dbb5..6e409eabe1c9 100644 --- a/drivers/spi/spi-bcm53xx.c +++ b/drivers/spi/spi-bcm53xx.c @@ -1,3 +1,11 @@ +/* + * Copyright (C) 2014-2016 Rafał Miłecki + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include @@ -275,10 +283,6 @@ static int bcm53xxspi_flash_read(struct spi_device *spi, * BCMA **************************************************/ -static struct spi_board_info bcm53xx_info = { - .modalias = "bcm53xxspiflash", -}; - static const struct bcma_device_id bcm53xxspi_bcma_tbl[] = { BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_QSPI, BCMA_ANY_REV, BCMA_ANY_CLASS), {}, @@ -311,6 +315,7 @@ static int bcm53xxspi_bcma_probe(struct bcma_device *core) b53spi->bspi = true; bcm53xxspi_disable_bspi(b53spi); + master->dev.of_node = dev->of_node; master->transfer_one = bcm53xxspi_transfer_one; if (b53spi->mmio_base) master->spi_flash_read = bcm53xxspi_flash_read; @@ -324,9 +329,6 @@ static int bcm53xxspi_bcma_probe(struct bcma_device *core) return err; } - /* Broadcom SoCs (at least with the CC rev 42) use SPI for flash only */ - spi_new_device(master, &bcm53xx_info); - return 0; } @@ -361,4 +363,4 @@ module_exit(bcm53xxspi_module_exit); MODULE_DESCRIPTION("Broadcom BCM53xx SPI Controller driver"); MODULE_AUTHOR("Rafał Miłecki "); -MODULE_LICENSE("GPL"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c index 054012f87567..b217c22ff72f 100644 --- a/drivers/spi/spi-dw.c +++ b/drivers/spi/spi-dw.c @@ -107,9 +107,9 @@ static const struct file_operations dw_spi_regs_ops = { static int dw_spi_debugfs_init(struct dw_spi *dws) { - char name[128]; + char name[32]; - snprintf(name, 128, "dw_spi-%s", dev_name(&dws->master->dev)); + snprintf(name, 32, "dw_spi%d", dws->master->bus_num); dws->debugfs = debugfs_create_dir(name, NULL); if (!dws->debugfs) return -ENOMEM; @@ -486,9 +486,9 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws) dws->type = SSI_MOTO_SPI; dws->dma_inited = 0; dws->dma_addr = (dma_addr_t)(dws->paddr + DW_SPI_DR); - snprintf(dws->name, sizeof(dws->name), "dw_spi%d", dws->bus_num); - ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dws->name, master); + ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dev_name(dev), + master); if (ret < 0) { dev_err(dev, "can not get IRQ\n"); goto err_free_master; diff --git a/drivers/spi/spi-dw.h b/drivers/spi/spi-dw.h index c21ca02f8ec5..da5eab62df34 100644 --- a/drivers/spi/spi-dw.h +++ b/drivers/spi/spi-dw.h @@ -101,7 +101,6 @@ struct dw_spi_dma_ops { struct dw_spi { struct spi_master *master; enum dw_ssi_type type; - char name[16]; void __iomem *regs; unsigned long paddr; diff --git a/drivers/spi/spi-ep93xx.c b/drivers/spi/spi-ep93xx.c index 17a6387e20b5..b5d766064b7b 100644 --- a/drivers/spi/spi-ep93xx.c +++ b/drivers/spi/spi-ep93xx.c @@ -28,6 +28,7 @@ #include #include #include +#include #include #include @@ -107,16 +108,6 @@ struct ep93xx_spi { void *zeropage; }; -/** - * struct ep93xx_spi_chip - SPI device hardware settings - * @spi: back pointer to the SPI device - * @ops: private chip operations - */ -struct ep93xx_spi_chip { - const struct spi_device *spi; - struct ep93xx_spi_chip_ops *ops; -}; - /* converts bits per word to CR0.DSS value */ #define bits_per_word_to_dss(bpw) ((bpw) - 1) @@ -229,104 +220,36 @@ static int ep93xx_spi_calc_divisors(const struct ep93xx_spi *espi, return -EINVAL; } -static void ep93xx_spi_cs_control(struct spi_device *spi, bool control) +static void ep93xx_spi_cs_control(struct spi_device *spi, bool enable) { - struct ep93xx_spi_chip *chip = spi_get_ctldata(spi); - int value = (spi->mode & SPI_CS_HIGH) ? control : !control; + if (spi->mode & SPI_CS_HIGH) + enable = !enable; - if (chip->ops && chip->ops->cs_control) - chip->ops->cs_control(spi, value); + if (gpio_is_valid(spi->cs_gpio)) + gpio_set_value(spi->cs_gpio, !enable); } -/** - * ep93xx_spi_setup() - setup an SPI device - * @spi: SPI device to setup - * - * This function sets up SPI device mode, speed etc. Can be called multiple - * times for a single device. Returns %0 in case of success, negative error in - * case of failure. When this function returns success, the device is - * deselected. - */ -static int ep93xx_spi_setup(struct spi_device *spi) -{ - struct ep93xx_spi *espi = spi_master_get_devdata(spi->master); - struct ep93xx_spi_chip *chip; - - chip = spi_get_ctldata(spi); - if (!chip) { - dev_dbg(&espi->pdev->dev, "initial setup for %s\n", - spi->modalias); - - chip = kzalloc(sizeof(*chip), GFP_KERNEL); - if (!chip) - return -ENOMEM; - - chip->spi = spi; - chip->ops = spi->controller_data; - - if (chip->ops && chip->ops->setup) { - int ret = chip->ops->setup(spi); - - if (ret) { - kfree(chip); - return ret; - } - } - - spi_set_ctldata(spi, chip); - } - - ep93xx_spi_cs_control(spi, false); - return 0; -} - -/** - * ep93xx_spi_cleanup() - cleans up master controller specific state - * @spi: SPI device to cleanup - * - * This function releases master controller specific state for given @spi - * device. - */ -static void ep93xx_spi_cleanup(struct spi_device *spi) -{ - struct ep93xx_spi_chip *chip; - - chip = spi_get_ctldata(spi); - if (chip) { - if (chip->ops && chip->ops->cleanup) - chip->ops->cleanup(spi); - spi_set_ctldata(spi, NULL); - kfree(chip); - } -} - -/** - * ep93xx_spi_chip_setup() - configures hardware according to given @chip - * @espi: ep93xx SPI controller struct - * @chip: chip specific settings - * @speed_hz: transfer speed - * @bits_per_word: transfer bits_per_word - */ static int ep93xx_spi_chip_setup(const struct ep93xx_spi *espi, - const struct ep93xx_spi_chip *chip, - u32 speed_hz, u8 bits_per_word) + struct spi_device *spi, + struct spi_transfer *xfer) { - u8 dss = bits_per_word_to_dss(bits_per_word); + u8 dss = bits_per_word_to_dss(xfer->bits_per_word); u8 div_cpsr = 0; u8 div_scr = 0; u16 cr0; int err; - err = ep93xx_spi_calc_divisors(espi, speed_hz, &div_cpsr, &div_scr); + err = ep93xx_spi_calc_divisors(espi, xfer->speed_hz, + &div_cpsr, &div_scr); if (err) return err; cr0 = div_scr << SSPCR0_SCR_SHIFT; - cr0 |= (chip->spi->mode & (SPI_CPHA|SPI_CPOL)) << SSPCR0_MODE_SHIFT; + cr0 |= (spi->mode & (SPI_CPHA | SPI_CPOL)) << SSPCR0_MODE_SHIFT; cr0 |= dss; dev_dbg(&espi->pdev->dev, "setup: mode %d, cpsr %d, scr %d, dss %d\n", - chip->spi->mode, div_cpsr, div_scr, dss); + spi->mode, div_cpsr, div_scr, dss); dev_dbg(&espi->pdev->dev, "setup: cr0 %#x\n", cr0); ep93xx_spi_write_u8(espi, SSPCPSR, div_cpsr); @@ -603,12 +526,11 @@ static void ep93xx_spi_process_transfer(struct ep93xx_spi *espi, struct spi_message *msg, struct spi_transfer *t) { - struct ep93xx_spi_chip *chip = spi_get_ctldata(msg->spi); int err; msg->state = t; - err = ep93xx_spi_chip_setup(espi, chip, t->speed_hz, t->bits_per_word); + err = ep93xx_spi_chip_setup(espi, msg->spi, t); if (err) { dev_err(&espi->pdev->dev, "failed to setup chip for transfer\n"); @@ -863,8 +785,13 @@ static int ep93xx_spi_probe(struct platform_device *pdev) struct resource *res; int irq; int error; + int i; info = dev_get_platdata(&pdev->dev); + if (!info) { + dev_err(&pdev->dev, "missing platform data\n"); + return -EINVAL; + } irq = platform_get_irq(pdev, 0); if (irq < 0) { @@ -882,14 +809,36 @@ static int ep93xx_spi_probe(struct platform_device *pdev) if (!master) return -ENOMEM; - master->setup = ep93xx_spi_setup; master->transfer_one_message = ep93xx_spi_transfer_one_message; - master->cleanup = ep93xx_spi_cleanup; master->bus_num = pdev->id; - master->num_chipselect = info->num_chipselect; master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 16); + master->num_chipselect = info->num_chipselect; + master->cs_gpios = devm_kzalloc(&master->dev, + sizeof(int) * master->num_chipselect, + GFP_KERNEL); + if (!master->cs_gpios) { + error = -ENOMEM; + goto fail_release_master; + } + + for (i = 0; i < master->num_chipselect; i++) { + master->cs_gpios[i] = info->chipselect[i]; + + if (!gpio_is_valid(master->cs_gpios[i])) + continue; + + error = devm_gpio_request_one(&pdev->dev, master->cs_gpios[i], + GPIOF_OUT_INIT_HIGH, + "ep93xx-spi"); + if (error) { + dev_err(&pdev->dev, "could not request cs gpio %d\n", + master->cs_gpios[i]); + goto fail_release_master; + } + } + platform_set_drvdata(pdev, master); espi = spi_master_get_devdata(master); diff --git a/drivers/spi/spi-fsl-lpspi.c b/drivers/spi/spi-fsl-lpspi.c index 52551f6d0c7d..cb3c73007ca1 100644 --- a/drivers/spi/spi-fsl-lpspi.c +++ b/drivers/spi/spi-fsl-lpspi.c @@ -366,7 +366,7 @@ static int fsl_lpspi_transfer_one_msg(struct spi_master *master, struct spi_transfer *xfer; bool is_first_xfer = true; u32 temp; - int ret; + int ret = 0; msg->status = 0; msg->actual_length = 0; @@ -512,9 +512,9 @@ static int fsl_lpspi_remove(struct platform_device *pdev) static struct platform_driver fsl_lpspi_driver = { .driver = { - .name = DRIVER_NAME, - .of_match_table = fsl_lpspi_dt_ids, - }, + .name = DRIVER_NAME, + .of_match_table = fsl_lpspi_dt_ids, + }, .probe = fsl_lpspi_probe, .remove = fsl_lpspi_remove, }; diff --git a/drivers/spi/spi-fsl-spi.c b/drivers/spi/spi-fsl-spi.c index 8b290d9d7935..0fc3452652ae 100644 --- a/drivers/spi/spi-fsl-spi.c +++ b/drivers/spi/spi-fsl-spi.c @@ -267,10 +267,9 @@ static int fsl_spi_setup_transfer(struct spi_device *spi, if ((mpc8xxx_spi->spibrg / hz) > 64) { cs->hw_mode |= SPMODE_DIV16; pm = (mpc8xxx_spi->spibrg - 1) / (hz * 64) + 1; - - WARN_ONCE(pm > 16, "%s: Requested speed is too low: %d Hz. " - "Will use %d Hz instead.\n", dev_name(&spi->dev), - hz, mpc8xxx_spi->spibrg / 1024); + WARN_ONCE(pm > 16, + "%s: Requested speed is too low: %d Hz. Will use %d Hz instead.\n", + dev_name(&spi->dev), hz, mpc8xxx_spi->spibrg / 1024); if (pm > 16) pm = 16; } else { @@ -727,12 +726,13 @@ static int of_fsl_spi_get_chipselects(struct device *dev) return 0; } - pinfo->gpios = kmalloc(ngpios * sizeof(*pinfo->gpios), GFP_KERNEL); + pinfo->gpios = kmalloc_array(ngpios, sizeof(*pinfo->gpios), + GFP_KERNEL); if (!pinfo->gpios) return -ENOMEM; memset(pinfo->gpios, -1, ngpios * sizeof(*pinfo->gpios)); - pinfo->alow_flags = kzalloc(ngpios * sizeof(*pinfo->alow_flags), + pinfo->alow_flags = kcalloc(ngpios, sizeof(*pinfo->alow_flags), GFP_KERNEL); if (!pinfo->alow_flags) { ret = -ENOMEM; @@ -762,8 +762,9 @@ static int of_fsl_spi_get_chipselects(struct device *dev) ret = gpio_direction_output(pinfo->gpios[i], pinfo->alow_flags[i]); if (ret) { - dev_err(dev, "can't set output direction for gpio " - "#%d: %d\n", i, ret); + dev_err(dev, + "can't set output direction for gpio #%d: %d\n", + i, ret); goto err_loop; } } diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c index 32ced64a5bb9..9a7c62f471dc 100644 --- a/drivers/spi/spi-imx.c +++ b/drivers/spi/spi-imx.c @@ -211,7 +211,7 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi, struct spi_transfer *transfer) { struct spi_imx_data *spi_imx = spi_master_get_devdata(master); - unsigned int bpw; + unsigned int bpw, i; if (!master->dma_rx) return false; @@ -228,11 +228,15 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi, if (bpw != 1 && bpw != 2 && bpw != 4) return false; - if (transfer->len < spi_imx->wml * bpw) + for (i = spi_imx_get_fifosize(spi_imx) / 2; i > 0; i--) { + if (!(transfer->len % (i * bpw))) + break; + } + + if (i == 0) return false; - if (transfer->len % (spi_imx->wml * bpw)) - return false; + spi_imx->wml = i; return true; } @@ -837,10 +841,6 @@ static int spi_imx_dma_configure(struct spi_master *master, struct dma_slave_config rx = {}, tx = {}; struct spi_imx_data *spi_imx = spi_master_get_devdata(master); - if (bytes_per_word == spi_imx->bytes_per_word) - /* Same as last time */ - return 0; - switch (bytes_per_word) { case 4: buswidth = DMA_SLAVE_BUSWIDTH_4_BYTES; diff --git a/drivers/spi/spi-lantiq-ssc.c b/drivers/spi/spi-lantiq-ssc.c new file mode 100644 index 000000000000..8a626f7fccea --- /dev/null +++ b/drivers/spi/spi-lantiq-ssc.c @@ -0,0 +1,983 @@ +/* + * Copyright (C) 2011-2015 Daniel Schwierzeck + * Copyright (C) 2016 Hauke Mehrtens + * + * This program is free software; you can distribute it and/or modify it + * under the terms of the GNU General Public License (Version 2) as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_LANTIQ +#include +#endif + +#define SPI_RX_IRQ_NAME "spi_rx" +#define SPI_TX_IRQ_NAME "spi_tx" +#define SPI_ERR_IRQ_NAME "spi_err" +#define SPI_FRM_IRQ_NAME "spi_frm" + +#define SPI_CLC 0x00 +#define SPI_PISEL 0x04 +#define SPI_ID 0x08 +#define SPI_CON 0x10 +#define SPI_STAT 0x14 +#define SPI_WHBSTATE 0x18 +#define SPI_TB 0x20 +#define SPI_RB 0x24 +#define SPI_RXFCON 0x30 +#define SPI_TXFCON 0x34 +#define SPI_FSTAT 0x38 +#define SPI_BRT 0x40 +#define SPI_BRSTAT 0x44 +#define SPI_SFCON 0x60 +#define SPI_SFSTAT 0x64 +#define SPI_GPOCON 0x70 +#define SPI_GPOSTAT 0x74 +#define SPI_FPGO 0x78 +#define SPI_RXREQ 0x80 +#define SPI_RXCNT 0x84 +#define SPI_DMACON 0xec +#define SPI_IRNEN 0xf4 +#define SPI_IRNICR 0xf8 +#define SPI_IRNCR 0xfc + +#define SPI_CLC_SMC_S 16 /* Clock divider for sleep mode */ +#define SPI_CLC_SMC_M (0xFF << SPI_CLC_SMC_S) +#define SPI_CLC_RMC_S 8 /* Clock divider for normal run mode */ +#define SPI_CLC_RMC_M (0xFF << SPI_CLC_RMC_S) +#define SPI_CLC_DISS BIT(1) /* Disable status bit */ +#define SPI_CLC_DISR BIT(0) /* Disable request bit */ + +#define SPI_ID_TXFS_S 24 /* Implemented TX FIFO size */ +#define SPI_ID_TXFS_M (0x3F << SPI_ID_TXFS_S) +#define SPI_ID_RXFS_S 16 /* Implemented RX FIFO size */ +#define SPI_ID_RXFS_M (0x3F << SPI_ID_RXFS_S) +#define SPI_ID_MOD_S 8 /* Module ID */ +#define SPI_ID_MOD_M (0xff << SPI_ID_MOD_S) +#define SPI_ID_CFG_S 5 /* DMA interface support */ +#define SPI_ID_CFG_M (1 << SPI_ID_CFG_S) +#define SPI_ID_REV_M 0x1F /* Hardware revision number */ + +#define SPI_CON_BM_S 16 /* Data width selection */ +#define SPI_CON_BM_M (0x1F << SPI_CON_BM_S) +#define SPI_CON_EM BIT(24) /* Echo mode */ +#define SPI_CON_IDLE BIT(23) /* Idle bit value */ +#define SPI_CON_ENBV BIT(22) /* Enable byte valid control */ +#define SPI_CON_RUEN BIT(12) /* Receive underflow error enable */ +#define SPI_CON_TUEN BIT(11) /* Transmit underflow error enable */ +#define SPI_CON_AEN BIT(10) /* Abort error enable */ +#define SPI_CON_REN BIT(9) /* Receive overflow error enable */ +#define SPI_CON_TEN BIT(8) /* Transmit overflow error enable */ +#define SPI_CON_LB BIT(7) /* Loopback control */ +#define SPI_CON_PO BIT(6) /* Clock polarity control */ +#define SPI_CON_PH BIT(5) /* Clock phase control */ +#define SPI_CON_HB BIT(4) /* Heading control */ +#define SPI_CON_RXOFF BIT(1) /* Switch receiver off */ +#define SPI_CON_TXOFF BIT(0) /* Switch transmitter off */ + +#define SPI_STAT_RXBV_S 28 +#define SPI_STAT_RXBV_M (0x7 << SPI_STAT_RXBV_S) +#define SPI_STAT_BSY BIT(13) /* Busy flag */ +#define SPI_STAT_RUE BIT(12) /* Receive underflow error flag */ +#define SPI_STAT_TUE BIT(11) /* Transmit underflow error flag */ +#define SPI_STAT_AE BIT(10) /* Abort error flag */ +#define SPI_STAT_RE BIT(9) /* Receive error flag */ +#define SPI_STAT_TE BIT(8) /* Transmit error flag */ +#define SPI_STAT_ME BIT(7) /* Mode error flag */ +#define SPI_STAT_MS BIT(1) /* Master/slave select bit */ +#define SPI_STAT_EN BIT(0) /* Enable bit */ +#define SPI_STAT_ERRORS (SPI_STAT_ME | SPI_STAT_TE | SPI_STAT_RE | \ + SPI_STAT_AE | SPI_STAT_TUE | SPI_STAT_RUE) + +#define SPI_WHBSTATE_SETTUE BIT(15) /* Set transmit underflow error flag */ +#define SPI_WHBSTATE_SETAE BIT(14) /* Set abort error flag */ +#define SPI_WHBSTATE_SETRE BIT(13) /* Set receive error flag */ +#define SPI_WHBSTATE_SETTE BIT(12) /* Set transmit error flag */ +#define SPI_WHBSTATE_CLRTUE BIT(11) /* Clear transmit underflow error flag */ +#define SPI_WHBSTATE_CLRAE BIT(10) /* Clear abort error flag */ +#define SPI_WHBSTATE_CLRRE BIT(9) /* Clear receive error flag */ +#define SPI_WHBSTATE_CLRTE BIT(8) /* Clear transmit error flag */ +#define SPI_WHBSTATE_SETME BIT(7) /* Set mode error flag */ +#define SPI_WHBSTATE_CLRME BIT(6) /* Clear mode error flag */ +#define SPI_WHBSTATE_SETRUE BIT(5) /* Set receive underflow error flag */ +#define SPI_WHBSTATE_CLRRUE BIT(4) /* Clear receive underflow error flag */ +#define SPI_WHBSTATE_SETMS BIT(3) /* Set master select bit */ +#define SPI_WHBSTATE_CLRMS BIT(2) /* Clear master select bit */ +#define SPI_WHBSTATE_SETEN BIT(1) /* Set enable bit (operational mode) */ +#define SPI_WHBSTATE_CLREN BIT(0) /* Clear enable bit (config mode */ +#define SPI_WHBSTATE_CLR_ERRORS (SPI_WHBSTATE_CLRRUE | SPI_WHBSTATE_CLRME | \ + SPI_WHBSTATE_CLRTE | SPI_WHBSTATE_CLRRE | \ + SPI_WHBSTATE_CLRAE | SPI_WHBSTATE_CLRTUE) + +#define SPI_RXFCON_RXFITL_S 8 /* FIFO interrupt trigger level */ +#define SPI_RXFCON_RXFITL_M (0x3F << SPI_RXFCON_RXFITL_S) +#define SPI_RXFCON_RXFLU BIT(1) /* FIFO flush */ +#define SPI_RXFCON_RXFEN BIT(0) /* FIFO enable */ + +#define SPI_TXFCON_TXFITL_S 8 /* FIFO interrupt trigger level */ +#define SPI_TXFCON_TXFITL_M (0x3F << SPI_TXFCON_TXFITL_S) +#define SPI_TXFCON_TXFLU BIT(1) /* FIFO flush */ +#define SPI_TXFCON_TXFEN BIT(0) /* FIFO enable */ + +#define SPI_FSTAT_RXFFL_S 0 +#define SPI_FSTAT_RXFFL_M (0x3f << SPI_FSTAT_RXFFL_S) +#define SPI_FSTAT_TXFFL_S 8 +#define SPI_FSTAT_TXFFL_M (0x3f << SPI_FSTAT_TXFFL_S) + +#define SPI_GPOCON_ISCSBN_S 8 +#define SPI_GPOCON_INVOUTN_S 0 + +#define SPI_FGPO_SETOUTN_S 8 +#define SPI_FGPO_CLROUTN_S 0 + +#define SPI_RXREQ_RXCNT_M 0xFFFF /* Receive count value */ +#define SPI_RXCNT_TODO_M 0xFFFF /* Recevie to-do value */ + +#define SPI_IRNEN_TFI BIT(4) /* TX finished interrupt */ +#define SPI_IRNEN_F BIT(3) /* Frame end interrupt request */ +#define SPI_IRNEN_E BIT(2) /* Error end interrupt request */ +#define SPI_IRNEN_T_XWAY BIT(1) /* Transmit end interrupt request */ +#define SPI_IRNEN_R_XWAY BIT(0) /* Receive end interrupt request */ +#define SPI_IRNEN_R_XRX BIT(1) /* Transmit end interrupt request */ +#define SPI_IRNEN_T_XRX BIT(0) /* Receive end interrupt request */ +#define SPI_IRNEN_ALL 0x1F + +struct lantiq_ssc_hwcfg { + unsigned int irnen_r; + unsigned int irnen_t; +}; + +struct lantiq_ssc_spi { + struct spi_master *master; + struct device *dev; + void __iomem *regbase; + struct clk *spi_clk; + struct clk *fpi_clk; + const struct lantiq_ssc_hwcfg *hwcfg; + + spinlock_t lock; + struct workqueue_struct *wq; + struct work_struct work; + + const u8 *tx; + u8 *rx; + unsigned int tx_todo; + unsigned int rx_todo; + unsigned int bits_per_word; + unsigned int speed_hz; + unsigned int tx_fifo_size; + unsigned int rx_fifo_size; + unsigned int base_cs; +}; + +static u32 lantiq_ssc_readl(const struct lantiq_ssc_spi *spi, u32 reg) +{ + return __raw_readl(spi->regbase + reg); +} + +static void lantiq_ssc_writel(const struct lantiq_ssc_spi *spi, u32 val, + u32 reg) +{ + __raw_writel(val, spi->regbase + reg); +} + +static void lantiq_ssc_maskl(const struct lantiq_ssc_spi *spi, u32 clr, + u32 set, u32 reg) +{ + u32 val = __raw_readl(spi->regbase + reg); + + val &= ~clr; + val |= set; + __raw_writel(val, spi->regbase + reg); +} + +static unsigned int tx_fifo_level(const struct lantiq_ssc_spi *spi) +{ + u32 fstat = lantiq_ssc_readl(spi, SPI_FSTAT); + + return (fstat & SPI_FSTAT_TXFFL_M) >> SPI_FSTAT_TXFFL_S; +} + +static unsigned int rx_fifo_level(const struct lantiq_ssc_spi *spi) +{ + u32 fstat = lantiq_ssc_readl(spi, SPI_FSTAT); + + return fstat & SPI_FSTAT_RXFFL_M; +} + +static unsigned int tx_fifo_free(const struct lantiq_ssc_spi *spi) +{ + return spi->tx_fifo_size - tx_fifo_level(spi); +} + +static void rx_fifo_reset(const struct lantiq_ssc_spi *spi) +{ + u32 val = spi->rx_fifo_size << SPI_RXFCON_RXFITL_S; + + val |= SPI_RXFCON_RXFEN | SPI_RXFCON_RXFLU; + lantiq_ssc_writel(spi, val, SPI_RXFCON); +} + +static void tx_fifo_reset(const struct lantiq_ssc_spi *spi) +{ + u32 val = 1 << SPI_TXFCON_TXFITL_S; + + val |= SPI_TXFCON_TXFEN | SPI_TXFCON_TXFLU; + lantiq_ssc_writel(spi, val, SPI_TXFCON); +} + +static void rx_fifo_flush(const struct lantiq_ssc_spi *spi) +{ + lantiq_ssc_maskl(spi, 0, SPI_RXFCON_RXFLU, SPI_RXFCON); +} + +static void tx_fifo_flush(const struct lantiq_ssc_spi *spi) +{ + lantiq_ssc_maskl(spi, 0, SPI_TXFCON_TXFLU, SPI_TXFCON); +} + +static void hw_enter_config_mode(const struct lantiq_ssc_spi *spi) +{ + lantiq_ssc_writel(spi, SPI_WHBSTATE_CLREN, SPI_WHBSTATE); +} + +static void hw_enter_active_mode(const struct lantiq_ssc_spi *spi) +{ + lantiq_ssc_writel(spi, SPI_WHBSTATE_SETEN, SPI_WHBSTATE); +} + +static void hw_setup_speed_hz(const struct lantiq_ssc_spi *spi, + unsigned int max_speed_hz) +{ + u32 spi_clk, brt; + + /* + * SPI module clock is derived from FPI bus clock dependent on + * divider value in CLC.RMS which is always set to 1. + * + * f_SPI + * baudrate = -------------- + * 2 * (BR + 1) + */ + spi_clk = clk_get_rate(spi->fpi_clk) / 2; + + if (max_speed_hz > spi_clk) + brt = 0; + else + brt = spi_clk / max_speed_hz - 1; + + if (brt > 0xFFFF) + brt = 0xFFFF; + + dev_dbg(spi->dev, "spi_clk %u, max_speed_hz %u, brt %u\n", + spi_clk, max_speed_hz, brt); + + lantiq_ssc_writel(spi, brt, SPI_BRT); +} + +static void hw_setup_bits_per_word(const struct lantiq_ssc_spi *spi, + unsigned int bits_per_word) +{ + u32 bm; + + /* CON.BM value = bits_per_word - 1 */ + bm = (bits_per_word - 1) << SPI_CON_BM_S; + + lantiq_ssc_maskl(spi, SPI_CON_BM_M, bm, SPI_CON); +} + +static void hw_setup_clock_mode(const struct lantiq_ssc_spi *spi, + unsigned int mode) +{ + u32 con_set = 0, con_clr = 0; + + /* + * SPI mode mapping in CON register: + * Mode CPOL CPHA CON.PO CON.PH + * 0 0 0 0 1 + * 1 0 1 0 0 + * 2 1 0 1 1 + * 3 1 1 1 0 + */ + if (mode & SPI_CPHA) + con_clr |= SPI_CON_PH; + else + con_set |= SPI_CON_PH; + + if (mode & SPI_CPOL) + con_set |= SPI_CON_PO | SPI_CON_IDLE; + else + con_clr |= SPI_CON_PO | SPI_CON_IDLE; + + /* Set heading control */ + if (mode & SPI_LSB_FIRST) + con_clr |= SPI_CON_HB; + else + con_set |= SPI_CON_HB; + + /* Set loopback mode */ + if (mode & SPI_LOOP) + con_set |= SPI_CON_LB; + else + con_clr |= SPI_CON_LB; + + lantiq_ssc_maskl(spi, con_clr, con_set, SPI_CON); +} + +static void lantiq_ssc_hw_init(const struct lantiq_ssc_spi *spi) +{ + const struct lantiq_ssc_hwcfg *hwcfg = spi->hwcfg; + + /* + * Set clock divider for run mode to 1 to + * run at same frequency as FPI bus + */ + lantiq_ssc_writel(spi, 1 << SPI_CLC_RMC_S, SPI_CLC); + + /* Put controller into config mode */ + hw_enter_config_mode(spi); + + /* Clear error flags */ + lantiq_ssc_maskl(spi, 0, SPI_WHBSTATE_CLR_ERRORS, SPI_WHBSTATE); + + /* Enable error checking, disable TX/RX */ + lantiq_ssc_writel(spi, SPI_CON_RUEN | SPI_CON_AEN | SPI_CON_TEN | + SPI_CON_REN | SPI_CON_TXOFF | SPI_CON_RXOFF, SPI_CON); + + /* Setup default SPI mode */ + hw_setup_bits_per_word(spi, spi->bits_per_word); + hw_setup_clock_mode(spi, SPI_MODE_0); + + /* Enable master mode and clear error flags */ + lantiq_ssc_writel(spi, SPI_WHBSTATE_SETMS | SPI_WHBSTATE_CLR_ERRORS, + SPI_WHBSTATE); + + /* Reset GPIO/CS registers */ + lantiq_ssc_writel(spi, 0, SPI_GPOCON); + lantiq_ssc_writel(spi, 0xFF00, SPI_FPGO); + + /* Enable and flush FIFOs */ + rx_fifo_reset(spi); + tx_fifo_reset(spi); + + /* Enable interrupts */ + lantiq_ssc_writel(spi, hwcfg->irnen_t | hwcfg->irnen_r | SPI_IRNEN_E, + SPI_IRNEN); +} + +static int lantiq_ssc_setup(struct spi_device *spidev) +{ + struct spi_master *master = spidev->master; + struct lantiq_ssc_spi *spi = spi_master_get_devdata(master); + unsigned int cs = spidev->chip_select; + u32 gpocon; + + /* GPIOs are used for CS */ + if (gpio_is_valid(spidev->cs_gpio)) + return 0; + + dev_dbg(spi->dev, "using internal chipselect %u\n", cs); + + if (cs < spi->base_cs) { + dev_err(spi->dev, + "chipselect %i too small (min %i)\n", cs, spi->base_cs); + return -EINVAL; + } + + /* set GPO pin to CS mode */ + gpocon = 1 << ((cs - spi->base_cs) + SPI_GPOCON_ISCSBN_S); + + /* invert GPO pin */ + if (spidev->mode & SPI_CS_HIGH) + gpocon |= 1 << (cs - spi->base_cs); + + lantiq_ssc_maskl(spi, 0, gpocon, SPI_GPOCON); + + return 0; +} + +static int lantiq_ssc_prepare_message(struct spi_master *master, + struct spi_message *message) +{ + struct lantiq_ssc_spi *spi = spi_master_get_devdata(master); + + hw_enter_config_mode(spi); + hw_setup_clock_mode(spi, message->spi->mode); + hw_enter_active_mode(spi); + + return 0; +} + +static void hw_setup_transfer(struct lantiq_ssc_spi *spi, + struct spi_device *spidev, struct spi_transfer *t) +{ + unsigned int speed_hz = t->speed_hz; + unsigned int bits_per_word = t->bits_per_word; + u32 con; + + if (bits_per_word != spi->bits_per_word || + speed_hz != spi->speed_hz) { + hw_enter_config_mode(spi); + hw_setup_speed_hz(spi, speed_hz); + hw_setup_bits_per_word(spi, bits_per_word); + hw_enter_active_mode(spi); + + spi->speed_hz = speed_hz; + spi->bits_per_word = bits_per_word; + } + + /* Configure transmitter and receiver */ + con = lantiq_ssc_readl(spi, SPI_CON); + if (t->tx_buf) + con &= ~SPI_CON_TXOFF; + else + con |= SPI_CON_TXOFF; + + if (t->rx_buf) + con &= ~SPI_CON_RXOFF; + else + con |= SPI_CON_RXOFF; + + lantiq_ssc_writel(spi, con, SPI_CON); +} + +static int lantiq_ssc_unprepare_message(struct spi_master *master, + struct spi_message *message) +{ + struct lantiq_ssc_spi *spi = spi_master_get_devdata(master); + + flush_workqueue(spi->wq); + + /* Disable transmitter and receiver while idle */ + lantiq_ssc_maskl(spi, 0, SPI_CON_TXOFF | SPI_CON_RXOFF, SPI_CON); + + return 0; +} + +static void tx_fifo_write(struct lantiq_ssc_spi *spi) +{ + const u8 *tx8; + const u16 *tx16; + const u32 *tx32; + u32 data; + unsigned int tx_free = tx_fifo_free(spi); + + while (spi->tx_todo && tx_free) { + switch (spi->bits_per_word) { + case 2 ... 8: + tx8 = spi->tx; + data = *tx8; + spi->tx_todo--; + spi->tx++; + break; + case 16: + tx16 = (u16 *) spi->tx; + data = *tx16; + spi->tx_todo -= 2; + spi->tx += 2; + break; + case 32: + tx32 = (u32 *) spi->tx; + data = *tx32; + spi->tx_todo -= 4; + spi->tx += 4; + break; + default: + WARN_ON(1); + data = 0; + break; + } + + lantiq_ssc_writel(spi, data, SPI_TB); + tx_free--; + } +} + +static void rx_fifo_read_full_duplex(struct lantiq_ssc_spi *spi) +{ + u8 *rx8; + u16 *rx16; + u32 *rx32; + u32 data; + unsigned int rx_fill = rx_fifo_level(spi); + + while (rx_fill) { + data = lantiq_ssc_readl(spi, SPI_RB); + + switch (spi->bits_per_word) { + case 2 ... 8: + rx8 = spi->rx; + *rx8 = data; + spi->rx_todo--; + spi->rx++; + break; + case 16: + rx16 = (u16 *) spi->rx; + *rx16 = data; + spi->rx_todo -= 2; + spi->rx += 2; + break; + case 32: + rx32 = (u32 *) spi->rx; + *rx32 = data; + spi->rx_todo -= 4; + spi->rx += 4; + break; + default: + WARN_ON(1); + break; + } + + rx_fill--; + } +} + +static void rx_fifo_read_half_duplex(struct lantiq_ssc_spi *spi) +{ + u32 data, *rx32; + u8 *rx8; + unsigned int rxbv, shift; + unsigned int rx_fill = rx_fifo_level(spi); + + /* + * In RX-only mode the bits per word value is ignored by HW. A value + * of 32 is used instead. Thus all 4 bytes per FIFO must be read. + * If remaining RX bytes are less than 4, the FIFO must be read + * differently. The amount of received and valid bytes is indicated + * by STAT.RXBV register value. + */ + while (rx_fill) { + if (spi->rx_todo < 4) { + rxbv = (lantiq_ssc_readl(spi, SPI_STAT) & + SPI_STAT_RXBV_M) >> SPI_STAT_RXBV_S; + data = lantiq_ssc_readl(spi, SPI_RB); + + shift = (rxbv - 1) * 8; + rx8 = spi->rx; + + while (rxbv) { + *rx8++ = (data >> shift) & 0xFF; + rxbv--; + shift -= 8; + spi->rx_todo--; + spi->rx++; + } + } else { + data = lantiq_ssc_readl(spi, SPI_RB); + rx32 = (u32 *) spi->rx; + + *rx32++ = data; + spi->rx_todo -= 4; + spi->rx += 4; + } + rx_fill--; + } +} + +static void rx_request(struct lantiq_ssc_spi *spi) +{ + unsigned int rxreq, rxreq_max; + + /* + * To avoid receive overflows at high clocks it is better to request + * only the amount of bytes that fits into all FIFOs. This value + * depends on the FIFO size implemented in hardware. + */ + rxreq = spi->rx_todo; + rxreq_max = spi->rx_fifo_size * 4; + if (rxreq > rxreq_max) + rxreq = rxreq_max; + + lantiq_ssc_writel(spi, rxreq, SPI_RXREQ); +} + +static irqreturn_t lantiq_ssc_xmit_interrupt(int irq, void *data) +{ + struct lantiq_ssc_spi *spi = data; + + if (spi->tx) { + if (spi->rx && spi->rx_todo) + rx_fifo_read_full_duplex(spi); + + if (spi->tx_todo) + tx_fifo_write(spi); + else if (!tx_fifo_level(spi)) + goto completed; + } else if (spi->rx) { + if (spi->rx_todo) { + rx_fifo_read_half_duplex(spi); + + if (spi->rx_todo) + rx_request(spi); + else + goto completed; + } else { + goto completed; + } + } + + return IRQ_HANDLED; + +completed: + queue_work(spi->wq, &spi->work); + + return IRQ_HANDLED; +} + +static irqreturn_t lantiq_ssc_err_interrupt(int irq, void *data) +{ + struct lantiq_ssc_spi *spi = data; + u32 stat = lantiq_ssc_readl(spi, SPI_STAT); + + if (!(stat & SPI_STAT_ERRORS)) + return IRQ_NONE; + + if (stat & SPI_STAT_RUE) + dev_err(spi->dev, "receive underflow error\n"); + if (stat & SPI_STAT_TUE) + dev_err(spi->dev, "transmit underflow error\n"); + if (stat & SPI_STAT_AE) + dev_err(spi->dev, "abort error\n"); + if (stat & SPI_STAT_RE) + dev_err(spi->dev, "receive overflow error\n"); + if (stat & SPI_STAT_TE) + dev_err(spi->dev, "transmit overflow error\n"); + if (stat & SPI_STAT_ME) + dev_err(spi->dev, "mode error\n"); + + /* Clear error flags */ + lantiq_ssc_maskl(spi, 0, SPI_WHBSTATE_CLR_ERRORS, SPI_WHBSTATE); + + /* set bad status so it can be retried */ + if (spi->master->cur_msg) + spi->master->cur_msg->status = -EIO; + queue_work(spi->wq, &spi->work); + + return IRQ_HANDLED; +} + +static int transfer_start(struct lantiq_ssc_spi *spi, struct spi_device *spidev, + struct spi_transfer *t) +{ + unsigned long flags; + + spin_lock_irqsave(&spi->lock, flags); + + spi->tx = t->tx_buf; + spi->rx = t->rx_buf; + + if (t->tx_buf) { + spi->tx_todo = t->len; + + /* initially fill TX FIFO */ + tx_fifo_write(spi); + } + + if (spi->rx) { + spi->rx_todo = t->len; + + /* start shift clock in RX-only mode */ + if (!spi->tx) + rx_request(spi); + } + + spin_unlock_irqrestore(&spi->lock, flags); + + return t->len; +} + +/* + * The driver only gets an interrupt when the FIFO is empty, but there + * is an additional shift register from which the data is written to + * the wire. We get the last interrupt when the controller starts to + * write the last word to the wire, not when it is finished. Do busy + * waiting till it finishes. + */ +static void lantiq_ssc_bussy_work(struct work_struct *work) +{ + struct lantiq_ssc_spi *spi; + unsigned long long timeout = 8LL * 1000LL; + unsigned long end; + + spi = container_of(work, typeof(*spi), work); + + do_div(timeout, spi->speed_hz); + timeout += timeout + 100; /* some tolerance */ + + end = jiffies + msecs_to_jiffies(timeout); + do { + u32 stat = lantiq_ssc_readl(spi, SPI_STAT); + + if (!(stat & SPI_STAT_BSY)) { + spi_finalize_current_transfer(spi->master); + return; + } + + cond_resched(); + } while (!time_after_eq(jiffies, end)); + + if (spi->master->cur_msg) + spi->master->cur_msg->status = -EIO; + spi_finalize_current_transfer(spi->master); +} + +static void lantiq_ssc_handle_err(struct spi_master *master, + struct spi_message *message) +{ + struct lantiq_ssc_spi *spi = spi_master_get_devdata(master); + + /* flush FIFOs on timeout */ + rx_fifo_flush(spi); + tx_fifo_flush(spi); +} + +static void lantiq_ssc_set_cs(struct spi_device *spidev, bool enable) +{ + struct lantiq_ssc_spi *spi = spi_master_get_devdata(spidev->master); + unsigned int cs = spidev->chip_select; + u32 fgpo; + + if (!!(spidev->mode & SPI_CS_HIGH) == enable) + fgpo = (1 << (cs - spi->base_cs)); + else + fgpo = (1 << (cs - spi->base_cs + SPI_FGPO_SETOUTN_S)); + + lantiq_ssc_writel(spi, fgpo, SPI_FPGO); +} + +static int lantiq_ssc_transfer_one(struct spi_master *master, + struct spi_device *spidev, + struct spi_transfer *t) +{ + struct lantiq_ssc_spi *spi = spi_master_get_devdata(master); + + hw_setup_transfer(spi, spidev, t); + + return transfer_start(spi, spidev, t); +} + +static const struct lantiq_ssc_hwcfg lantiq_ssc_xway = { + .irnen_r = SPI_IRNEN_R_XWAY, + .irnen_t = SPI_IRNEN_T_XWAY, +}; + +static const struct lantiq_ssc_hwcfg lantiq_ssc_xrx = { + .irnen_r = SPI_IRNEN_R_XRX, + .irnen_t = SPI_IRNEN_T_XRX, +}; + +static const struct of_device_id lantiq_ssc_match[] = { + { .compatible = "lantiq,ase-spi", .data = &lantiq_ssc_xway, }, + { .compatible = "lantiq,falcon-spi", .data = &lantiq_ssc_xrx, }, + { .compatible = "lantiq,xrx100-spi", .data = &lantiq_ssc_xrx, }, + {}, +}; +MODULE_DEVICE_TABLE(of, lantiq_ssc_match); + +static int lantiq_ssc_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct spi_master *master; + struct resource *res; + struct lantiq_ssc_spi *spi; + const struct lantiq_ssc_hwcfg *hwcfg; + const struct of_device_id *match; + int err, rx_irq, tx_irq, err_irq; + u32 id, supports_dma, revision; + unsigned int num_cs; + + match = of_match_device(lantiq_ssc_match, dev); + if (!match) { + dev_err(dev, "no device match\n"); + return -EINVAL; + } + hwcfg = match->data; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(dev, "failed to get resources\n"); + return -ENXIO; + } + + rx_irq = platform_get_irq_byname(pdev, SPI_RX_IRQ_NAME); + if (rx_irq < 0) { + dev_err(dev, "failed to get %s\n", SPI_RX_IRQ_NAME); + return -ENXIO; + } + + tx_irq = platform_get_irq_byname(pdev, SPI_TX_IRQ_NAME); + if (tx_irq < 0) { + dev_err(dev, "failed to get %s\n", SPI_TX_IRQ_NAME); + return -ENXIO; + } + + err_irq = platform_get_irq_byname(pdev, SPI_ERR_IRQ_NAME); + if (err_irq < 0) { + dev_err(dev, "failed to get %s\n", SPI_ERR_IRQ_NAME); + return -ENXIO; + } + + master = spi_alloc_master(dev, sizeof(struct lantiq_ssc_spi)); + if (!master) + return -ENOMEM; + + spi = spi_master_get_devdata(master); + spi->master = master; + spi->dev = dev; + spi->hwcfg = hwcfg; + platform_set_drvdata(pdev, spi); + + spi->regbase = devm_ioremap_resource(dev, res); + if (IS_ERR(spi->regbase)) { + err = PTR_ERR(spi->regbase); + goto err_master_put; + } + + err = devm_request_irq(dev, rx_irq, lantiq_ssc_xmit_interrupt, + 0, SPI_RX_IRQ_NAME, spi); + if (err) + goto err_master_put; + + err = devm_request_irq(dev, tx_irq, lantiq_ssc_xmit_interrupt, + 0, SPI_TX_IRQ_NAME, spi); + if (err) + goto err_master_put; + + err = devm_request_irq(dev, err_irq, lantiq_ssc_err_interrupt, + 0, SPI_ERR_IRQ_NAME, spi); + if (err) + goto err_master_put; + + spi->spi_clk = devm_clk_get(dev, "gate"); + if (IS_ERR(spi->spi_clk)) { + err = PTR_ERR(spi->spi_clk); + goto err_master_put; + } + err = clk_prepare_enable(spi->spi_clk); + if (err) + goto err_master_put; + + /* + * Use the old clk_get_fpi() function on Lantiq platform, till it + * supports common clk. + */ +#if defined(CONFIG_LANTIQ) && !defined(CONFIG_COMMON_CLK) + spi->fpi_clk = clk_get_fpi(); +#else + spi->fpi_clk = clk_get(dev, "freq"); +#endif + if (IS_ERR(spi->fpi_clk)) { + err = PTR_ERR(spi->fpi_clk); + goto err_clk_disable; + } + + num_cs = 8; + of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs); + + spi->base_cs = 1; + of_property_read_u32(pdev->dev.of_node, "base-cs", &spi->base_cs); + + spin_lock_init(&spi->lock); + spi->bits_per_word = 8; + spi->speed_hz = 0; + + master->dev.of_node = pdev->dev.of_node; + master->num_chipselect = num_cs; + master->setup = lantiq_ssc_setup; + master->set_cs = lantiq_ssc_set_cs; + master->handle_err = lantiq_ssc_handle_err; + master->prepare_message = lantiq_ssc_prepare_message; + master->unprepare_message = lantiq_ssc_unprepare_message; + master->transfer_one = lantiq_ssc_transfer_one; + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST | SPI_CS_HIGH | + SPI_LOOP; + master->bits_per_word_mask = SPI_BPW_RANGE_MASK(2, 8) | + SPI_BPW_MASK(16) | SPI_BPW_MASK(32); + + spi->wq = alloc_ordered_workqueue(dev_name(dev), 0); + if (!spi->wq) { + err = -ENOMEM; + goto err_clk_put; + } + INIT_WORK(&spi->work, lantiq_ssc_bussy_work); + + id = lantiq_ssc_readl(spi, SPI_ID); + spi->tx_fifo_size = (id & SPI_ID_TXFS_M) >> SPI_ID_TXFS_S; + spi->rx_fifo_size = (id & SPI_ID_RXFS_M) >> SPI_ID_RXFS_S; + supports_dma = (id & SPI_ID_CFG_M) >> SPI_ID_CFG_S; + revision = id & SPI_ID_REV_M; + + lantiq_ssc_hw_init(spi); + + dev_info(dev, + "Lantiq SSC SPI controller (Rev %i, TXFS %u, RXFS %u, DMA %u)\n", + revision, spi->tx_fifo_size, spi->rx_fifo_size, supports_dma); + + err = devm_spi_register_master(dev, master); + if (err) { + dev_err(dev, "failed to register spi_master\n"); + goto err_wq_destroy; + } + + return 0; + +err_wq_destroy: + destroy_workqueue(spi->wq); +err_clk_put: + clk_put(spi->fpi_clk); +err_clk_disable: + clk_disable_unprepare(spi->spi_clk); +err_master_put: + spi_master_put(master); + + return err; +} + +static int lantiq_ssc_remove(struct platform_device *pdev) +{ + struct lantiq_ssc_spi *spi = platform_get_drvdata(pdev); + + lantiq_ssc_writel(spi, 0, SPI_IRNEN); + lantiq_ssc_writel(spi, 0, SPI_CLC); + rx_fifo_flush(spi); + tx_fifo_flush(spi); + hw_enter_config_mode(spi); + + destroy_workqueue(spi->wq); + clk_disable_unprepare(spi->spi_clk); + clk_put(spi->fpi_clk); + + return 0; +} + +static struct platform_driver lantiq_ssc_driver = { + .probe = lantiq_ssc_probe, + .remove = lantiq_ssc_remove, + .driver = { + .name = "spi-lantiq-ssc", + .owner = THIS_MODULE, + .of_match_table = lantiq_ssc_match, + }, +}; +module_platform_driver(lantiq_ssc_driver); + +MODULE_DESCRIPTION("Lantiq SSC SPI controller driver"); +MODULE_AUTHOR("Daniel Schwierzeck "); +MODULE_AUTHOR("Hauke Mehrtens "); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:spi-lantiq-ssc"); diff --git a/drivers/spi/spi-mpc52xx.c b/drivers/spi/spi-mpc52xx.c index c36002110c30..e8b59ce4dc3a 100644 --- a/drivers/spi/spi-mpc52xx.c +++ b/drivers/spi/spi-mpc52xx.c @@ -437,8 +437,9 @@ static int mpc52xx_spi_probe(struct platform_device *op) ms->gpio_cs_count = of_gpio_count(op->dev.of_node); if (ms->gpio_cs_count > 0) { master->num_chipselect = ms->gpio_cs_count; - ms->gpio_cs = kmalloc(ms->gpio_cs_count * sizeof(unsigned int), - GFP_KERNEL); + ms->gpio_cs = kmalloc_array(ms->gpio_cs_count, + sizeof(*ms->gpio_cs), + GFP_KERNEL); if (!ms->gpio_cs) { rc = -ENOMEM; goto err_alloc_gpio; @@ -448,8 +449,7 @@ static int mpc52xx_spi_probe(struct platform_device *op) gpio_cs = of_get_gpio(op->dev.of_node, i); if (gpio_cs < 0) { dev_err(&op->dev, - "could not parse the gpio field " - "in oftree\n"); + "could not parse the gpio field in oftree\n"); rc = -ENODEV; goto err_gpio; } @@ -457,8 +457,8 @@ static int mpc52xx_spi_probe(struct platform_device *op) rc = gpio_request(gpio_cs, dev_name(&op->dev)); if (rc) { dev_err(&op->dev, - "can't request spi cs gpio #%d " - "on gpio line %d\n", i, gpio_cs); + "can't request spi cs gpio #%d on gpio line %d\n", + i, gpio_cs); goto err_gpio; } diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c index 899d7a8f0889..278867a31950 100644 --- a/drivers/spi/spi-mt65xx.c +++ b/drivers/spi/spi-mt65xx.c @@ -73,7 +73,7 @@ #define MTK_SPI_IDLE 0 #define MTK_SPI_PAUSED 1 -#define MTK_SPI_MAX_FIFO_SIZE 32 +#define MTK_SPI_MAX_FIFO_SIZE 32U #define MTK_SPI_PACKET_SIZE 1024 struct mtk_spi_compatible { @@ -333,7 +333,7 @@ static int mtk_spi_fifo_transfer(struct spi_master *master, struct mtk_spi *mdata = spi_master_get_devdata(master); mdata->cur_transfer = xfer; - mdata->xfer_len = xfer->len; + mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, xfer->len); mtk_spi_prepare_transfer(master, xfer); mtk_spi_setup_packet(master); @@ -410,7 +410,10 @@ static bool mtk_spi_can_dma(struct spi_master *master, struct spi_device *spi, struct spi_transfer *xfer) { - return xfer->len > MTK_SPI_MAX_FIFO_SIZE; + /* Buffers for DMA transactions must be 4-byte aligned */ + return (xfer->len > MTK_SPI_MAX_FIFO_SIZE && + (unsigned long)xfer->tx_buf % 4 == 0 && + (unsigned long)xfer->rx_buf % 4 == 0); } static int mtk_spi_setup(struct spi_device *spi) @@ -451,7 +454,33 @@ static irqreturn_t mtk_spi_interrupt(int irq, void *dev_id) ®_val, remainder); } } - spi_finalize_current_transfer(master); + + trans->len -= mdata->xfer_len; + if (!trans->len) { + spi_finalize_current_transfer(master); + return IRQ_HANDLED; + } + + if (trans->tx_buf) + trans->tx_buf += mdata->xfer_len; + if (trans->rx_buf) + trans->rx_buf += mdata->xfer_len; + + mdata->xfer_len = min(MTK_SPI_MAX_FIFO_SIZE, trans->len); + mtk_spi_setup_packet(master); + + cnt = trans->len / 4; + iowrite32_rep(mdata->base + SPI_TX_DATA_REG, trans->tx_buf, cnt); + + remainder = trans->len % 4; + if (remainder > 0) { + reg_val = 0; + memcpy(®_val, trans->tx_buf + (cnt * 4), remainder); + writel(reg_val, mdata->base + SPI_TX_DATA_REG); + } + + mtk_spi_enable_transfer(master); + return IRQ_HANDLED; } diff --git a/drivers/spi/spi-ppc4xx.c b/drivers/spi/spi-ppc4xx.c index dd3d0a218d8b..967d94844b30 100644 --- a/drivers/spi/spi-ppc4xx.c +++ b/drivers/spi/spi-ppc4xx.c @@ -411,7 +411,7 @@ static int spi_ppc4xx_of_probe(struct platform_device *op) if (num_gpios > 0) { int i; - hw->gpios = kzalloc(sizeof(int) * num_gpios, GFP_KERNEL); + hw->gpios = kcalloc(num_gpios, sizeof(*hw->gpios), GFP_KERNEL); if (!hw->gpios) { ret = -ENOMEM; goto free_master; @@ -428,8 +428,9 @@ static int spi_ppc4xx_of_probe(struct platform_device *op) /* Real CS - set the initial state. */ ret = gpio_request(gpio, np->name); if (ret < 0) { - dev_err(dev, "can't request gpio " - "#%d: %d\n", i, ret); + dev_err(dev, + "can't request gpio #%d: %d\n", + i, ret); goto free_gpios; } diff --git a/drivers/spi/spi-pxa2xx-pci.c b/drivers/spi/spi-pxa2xx-pci.c index 58d2d48e16a5..869f188b02eb 100644 --- a/drivers/spi/spi-pxa2xx-pci.c +++ b/drivers/spi/spi-pxa2xx-pci.c @@ -41,6 +41,13 @@ struct pxa_spi_info { static struct dw_dma_slave byt_tx_param = { .dst_id = 0 }; static struct dw_dma_slave byt_rx_param = { .src_id = 1 }; +static struct dw_dma_slave mrfld3_tx_param = { .dst_id = 15 }; +static struct dw_dma_slave mrfld3_rx_param = { .src_id = 14 }; +static struct dw_dma_slave mrfld5_tx_param = { .dst_id = 13 }; +static struct dw_dma_slave mrfld5_rx_param = { .src_id = 12 }; +static struct dw_dma_slave mrfld6_tx_param = { .dst_id = 11 }; +static struct dw_dma_slave mrfld6_rx_param = { .src_id = 10 }; + static struct dw_dma_slave bsw0_tx_param = { .dst_id = 0 }; static struct dw_dma_slave bsw0_rx_param = { .src_id = 1 }; static struct dw_dma_slave bsw1_tx_param = { .dst_id = 6 }; @@ -93,22 +100,39 @@ static int lpss_spi_setup(struct pci_dev *dev, struct pxa_spi_info *c) static int mrfld_spi_setup(struct pci_dev *dev, struct pxa_spi_info *c) { + struct pci_dev *dma_dev = pci_get_slot(dev->bus, PCI_DEVFN(21, 0)); + struct dw_dma_slave *tx, *rx; + switch (PCI_FUNC(dev->devfn)) { case 0: c->port_id = 3; c->num_chipselect = 1; + c->tx_param = &mrfld3_tx_param; + c->rx_param = &mrfld3_rx_param; break; case 1: c->port_id = 5; c->num_chipselect = 4; + c->tx_param = &mrfld5_tx_param; + c->rx_param = &mrfld5_rx_param; break; case 2: c->port_id = 6; c->num_chipselect = 1; + c->tx_param = &mrfld6_tx_param; + c->rx_param = &mrfld6_rx_param; break; default: return -ENODEV; } + + tx = c->tx_param; + tx->dma_dev = &dma_dev->dev; + + rx = c->rx_param; + rx->dma_dev = &dma_dev->dev; + + c->dma_filter = lpss_dma_filter; return 0; } @@ -203,10 +227,16 @@ static int pxa2xx_spi_pci_probe(struct pci_dev *dev, ssp = &spi_pdata.ssp; ssp->phys_base = pci_resource_start(dev, 0); ssp->mmio_base = pcim_iomap_table(dev)[0]; - ssp->irq = dev->irq; ssp->port_id = (c->port_id >= 0) ? c->port_id : dev->devfn; ssp->type = c->type; + pci_set_master(dev); + + ret = pci_alloc_irq_vectors(dev, 1, 1, PCI_IRQ_ALL_TYPES); + if (ret < 0) + return ret; + ssp->irq = pci_irq_vector(dev, 0); + snprintf(buf, sizeof(buf), "pxa2xx-spi.%d", ssp->port_id); ssp->clk = clk_register_fixed_rate(&dev->dev, buf , NULL, 0, c->max_clk_rate); diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c index d6239fa718be..47b65d7c4072 100644 --- a/drivers/spi/spi-pxa2xx.c +++ b/drivers/spi/spi-pxa2xx.c @@ -732,6 +732,20 @@ static irqreturn_t interrupt_transfer(struct driver_data *drv_data) return IRQ_HANDLED; } +static void handle_bad_msg(struct driver_data *drv_data) +{ + pxa2xx_spi_write(drv_data, SSCR0, + pxa2xx_spi_read(drv_data, SSCR0) & ~SSCR0_SSE); + pxa2xx_spi_write(drv_data, SSCR1, + pxa2xx_spi_read(drv_data, SSCR1) & ~drv_data->int_cr1); + if (!pxa25x_ssp_comp(drv_data)) + pxa2xx_spi_write(drv_data, SSTO, 0); + write_SSSR_CS(drv_data, drv_data->clear_sr); + + dev_err(&drv_data->pdev->dev, + "bad message state in interrupt handler\n"); +} + static irqreturn_t ssp_int(int irq, void *dev_id) { struct driver_data *drv_data = dev_id; @@ -771,21 +785,11 @@ static irqreturn_t ssp_int(int irq, void *dev_id) if (!(status & mask)) return IRQ_NONE; + pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg & ~drv_data->int_cr1); + pxa2xx_spi_write(drv_data, SSCR1, sccr1_reg); + if (!drv_data->master->cur_msg) { - - pxa2xx_spi_write(drv_data, SSCR0, - pxa2xx_spi_read(drv_data, SSCR0) - & ~SSCR0_SSE); - pxa2xx_spi_write(drv_data, SSCR1, - pxa2xx_spi_read(drv_data, SSCR1) - & ~drv_data->int_cr1); - if (!pxa25x_ssp_comp(drv_data)) - pxa2xx_spi_write(drv_data, SSTO, 0); - write_SSSR_CS(drv_data, drv_data->clear_sr); - - dev_err(&drv_data->pdev->dev, - "bad message state in interrupt handler\n"); - + handle_bad_msg(drv_data); /* Never fail */ return IRQ_HANDLED; } @@ -1458,6 +1462,10 @@ static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = { { PCI_VDEVICE(INTEL, 0x1ac2), LPSS_BXT_SSP }, { PCI_VDEVICE(INTEL, 0x1ac4), LPSS_BXT_SSP }, { PCI_VDEVICE(INTEL, 0x1ac6), LPSS_BXT_SSP }, + /* GLK */ + { PCI_VDEVICE(INTEL, 0x31c2), LPSS_BXT_SSP }, + { PCI_VDEVICE(INTEL, 0x31c4), LPSS_BXT_SSP }, + { PCI_VDEVICE(INTEL, 0x31c6), LPSS_BXT_SSP }, /* APL */ { PCI_VDEVICE(INTEL, 0x5ac2), LPSS_BXT_SSP }, { PCI_VDEVICE(INTEL, 0x5ac4), LPSS_BXT_SSP }, diff --git a/drivers/spi/spi-rockchip.c b/drivers/spi/spi-rockchip.c index 0f89c2169c24..acf31f36b898 100644 --- a/drivers/spi/spi-rockchip.c +++ b/drivers/spi/spi-rockchip.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include #include @@ -843,6 +844,8 @@ static int rockchip_spi_suspend(struct device *dev) clk_disable_unprepare(rs->apb_pclk); } + pinctrl_pm_select_sleep_state(dev); + return ret; } @@ -852,6 +855,8 @@ static int rockchip_spi_resume(struct device *dev) struct spi_master *master = dev_get_drvdata(dev); struct rockchip_spi *rs = spi_master_get_devdata(master); + pinctrl_pm_select_default_state(dev); + if (!pm_runtime_suspended(dev)) { ret = clk_prepare_enable(rs->apb_pclk); if (ret < 0) diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 9daf50031737..2a10b3f94ff7 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -808,7 +808,7 @@ static int qspi_transfer_out(struct rspi_data *rspi, struct spi_transfer *xfer) for (i = 0; i < len; i++) rspi_write_data(rspi, *tx++); } else { - ret = rspi_pio_transfer(rspi, tx, NULL, n); + ret = rspi_pio_transfer(rspi, tx, NULL, len); if (ret < 0) return ret; } @@ -845,10 +845,9 @@ static int qspi_transfer_in(struct rspi_data *rspi, struct spi_transfer *xfer) for (i = 0; i < len; i++) *rx++ = rspi_read_data(rspi); } else { - ret = rspi_pio_transfer(rspi, NULL, rx, n); + ret = rspi_pio_transfer(rspi, NULL, rx, len); if (ret < 0) return ret; - *rx++ = ret; } n -= len; } @@ -1227,10 +1226,8 @@ static int rspi_probe(struct platform_device *pdev) const struct spi_ops *ops; master = spi_alloc_master(&pdev->dev, sizeof(struct rspi_data)); - if (master == NULL) { - dev_err(&pdev->dev, "spi_alloc_master error.\n"); + if (master == NULL) return -ENOMEM; - } of_id = of_match_device(rspi_of_match, &pdev->dev); if (of_id) { diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index 28dfdce4beae..b392cca8fa4f 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -341,43 +341,16 @@ static void s3c64xx_spi_set_cs(struct spi_device *spi, bool enable) static int s3c64xx_spi_prepare_transfer(struct spi_master *spi) { struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi); - struct device *dev = &sdd->pdev->dev; if (is_polling(sdd)) return 0; - /* Acquire DMA channels */ - sdd->rx_dma.ch = dma_request_slave_channel(dev, "rx"); - if (!sdd->rx_dma.ch) { - dev_err(dev, "Failed to get RX DMA channel\n"); - return -EBUSY; - } spi->dma_rx = sdd->rx_dma.ch; - - sdd->tx_dma.ch = dma_request_slave_channel(dev, "tx"); - if (!sdd->tx_dma.ch) { - dev_err(dev, "Failed to get TX DMA channel\n"); - dma_release_channel(sdd->rx_dma.ch); - return -EBUSY; - } spi->dma_tx = sdd->tx_dma.ch; return 0; } -static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi) -{ - struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi); - - /* Free DMA channels */ - if (!is_polling(sdd)) { - dma_release_channel(sdd->rx_dma.ch); - dma_release_channel(sdd->tx_dma.ch); - } - - return 0; -} - static bool s3c64xx_spi_can_dma(struct spi_master *master, struct spi_device *spi, struct spi_transfer *xfer) @@ -996,7 +969,7 @@ static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) sci->num_cs = temp; } - sci->no_cs = of_property_read_bool(dev->of_node, "broken-cs"); + sci->no_cs = of_property_read_bool(dev->of_node, "no-cs-readback"); return sci; } @@ -1094,7 +1067,6 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer; master->prepare_message = s3c64xx_spi_prepare_message; master->transfer_one = s3c64xx_spi_transfer_one; - master->unprepare_transfer_hardware = s3c64xx_spi_unprepare_transfer; master->num_chipselect = sci->num_cs; master->dma_alignment = 8; master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) | @@ -1161,6 +1133,24 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) } } + if (!is_polling(sdd)) { + /* Acquire DMA channels */ + sdd->rx_dma.ch = dma_request_slave_channel_reason(&pdev->dev, + "rx"); + if (IS_ERR(sdd->rx_dma.ch)) { + dev_err(&pdev->dev, "Failed to get RX DMA channel\n"); + ret = PTR_ERR(sdd->rx_dma.ch); + goto err_disable_io_clk; + } + sdd->tx_dma.ch = dma_request_slave_channel_reason(&pdev->dev, + "tx"); + if (IS_ERR(sdd->tx_dma.ch)) { + dev_err(&pdev->dev, "Failed to get TX DMA channel\n"); + ret = PTR_ERR(sdd->tx_dma.ch); + goto err_release_rx_dma; + } + } + pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_TIMEOUT); pm_runtime_use_autosuspend(&pdev->dev); pm_runtime_set_active(&pdev->dev); @@ -1206,6 +1196,12 @@ err_pm_put: pm_runtime_disable(&pdev->dev); pm_runtime_set_suspended(&pdev->dev); + if (!is_polling(sdd)) + dma_release_channel(sdd->tx_dma.ch); +err_release_rx_dma: + if (!is_polling(sdd)) + dma_release_channel(sdd->rx_dma.ch); +err_disable_io_clk: clk_disable_unprepare(sdd->ioclk); err_disable_src_clk: clk_disable_unprepare(sdd->src_clk); @@ -1226,6 +1222,11 @@ static int s3c64xx_spi_remove(struct platform_device *pdev) writel(0, sdd->regs + S3C64XX_SPI_INT_EN); + if (!is_polling(sdd)) { + dma_release_channel(sdd->rx_dma.ch); + dma_release_channel(sdd->tx_dma.ch); + } + clk_disable_unprepare(sdd->ioclk); clk_disable_unprepare(sdd->src_clk); diff --git a/drivers/spi/spi-sh-msiof.c b/drivers/spi/spi-sh-msiof.c index 1f00eeb0b5a3..2ce15ca97782 100644 --- a/drivers/spi/spi-sh-msiof.c +++ b/drivers/spi/spi-sh-msiof.c @@ -1164,10 +1164,8 @@ static int sh_msiof_spi_probe(struct platform_device *pdev) int ret; master = spi_alloc_master(&pdev->dev, sizeof(struct sh_msiof_spi_priv)); - if (master == NULL) { - dev_err(&pdev->dev, "failed to allocate spi master\n"); + if (master == NULL) return -ENOMEM; - } p = spi_master_get_devdata(master); diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index ec6fb09e2e17..ad76a44fee6f 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -652,7 +652,8 @@ static int ti_qspi_probe(struct platform_device *pdev) r = platform_get_resource(pdev, IORESOURCE_MEM, 0); if (r == NULL) { dev_err(&pdev->dev, "missing platform data\n"); - return -ENODEV; + ret = -ENODEV; + goto free_master; } } @@ -669,7 +670,8 @@ static int ti_qspi_probe(struct platform_device *pdev) irq = platform_get_irq(pdev, 0); if (irq < 0) { dev_err(&pdev->dev, "no irq resource?\n"); - return irq; + ret = irq; + goto free_master; } mutex_init(&qspi->list_lock); @@ -685,15 +687,17 @@ static int ti_qspi_probe(struct platform_device *pdev) qspi->ctrl_base = syscon_regmap_lookup_by_phandle(np, "syscon-chipselects"); - if (IS_ERR(qspi->ctrl_base)) - return PTR_ERR(qspi->ctrl_base); + if (IS_ERR(qspi->ctrl_base)) { + ret = PTR_ERR(qspi->ctrl_base); + goto free_master; + } ret = of_property_read_u32_index(np, "syscon-chipselects", 1, &qspi->ctrl_reg); if (ret) { dev_err(&pdev->dev, "couldn't get ctrl_mod reg index\n"); - return ret; + goto free_master; } } @@ -714,9 +718,10 @@ static int ti_qspi_probe(struct platform_device *pdev) dma_cap_set(DMA_MEMCPY, mask); qspi->rx_chan = dma_request_chan_by_mask(&mask); - if (!qspi->rx_chan) { + if (IS_ERR(qspi->rx_chan)) { dev_err(qspi->dev, "No Rx DMA available, trying mmap mode\n"); + qspi->rx_chan = NULL; ret = 0; goto no_dma; } @@ -742,6 +747,7 @@ no_dma: if (!ret) return 0; + pm_runtime_disable(&pdev->dev); free_master: spi_master_put(master); return ret; diff --git a/drivers/spi/spi-topcliff-pch.c b/drivers/spi/spi-topcliff-pch.c index fcb991034c3d..97d137591b18 100644 --- a/drivers/spi/spi-topcliff-pch.c +++ b/drivers/spi/spi-topcliff-pch.c @@ -591,7 +591,6 @@ static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw) if (!data->pkt_rx_buff) { /* flush queue and set status of all transfers to -ENOMEM */ - dev_err(&data->master->dev, "%s :kzalloc failed\n", __func__); list_for_each_entry_safe(pmsg, tmp, data->queue.next, queue) { pmsg->status = -ENOMEM; @@ -622,8 +621,9 @@ static void pch_spi_set_tx(struct pch_spi_data *data, int *bpw) if (n_writes > PCH_MAX_FIFO_DEPTH) n_writes = PCH_MAX_FIFO_DEPTH; - dev_dbg(&data->master->dev, "\n%s:Pulling down SSN low - writing " - "0x2 to SSNXCR\n", __func__); + dev_dbg(&data->master->dev, + "\n%s:Pulling down SSN low - writing 0x2 to SSNXCR\n", + __func__); pch_spi_writereg(data->master, PCH_SSNXCR, SSN_LOW); for (j = 0; j < n_writes; j++) @@ -915,7 +915,6 @@ static void pch_spi_release_dma(struct pch_spi_data *data) dma_release_channel(dma->chan_rx); dma->chan_rx = NULL; } - return; } static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw) @@ -1008,7 +1007,7 @@ static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw) spin_unlock_irqrestore(&data->lock, flags); /* RX */ - dma->sg_rx_p = kzalloc(sizeof(struct scatterlist)*num, GFP_ATOMIC); + dma->sg_rx_p = kcalloc(num, sizeof(*dma->sg_rx_p), GFP_ATOMIC); sg_init_table(dma->sg_rx_p, num); /* Initialize SG table */ /* offset, length setting */ sg = dma->sg_rx_p; @@ -1068,7 +1067,7 @@ static void pch_spi_handle_dma(struct pch_spi_data *data, int *bpw) head = 0; } - dma->sg_tx_p = kzalloc(sizeof(struct scatterlist)*num, GFP_ATOMIC); + dma->sg_tx_p = kcalloc(num, sizeof(*dma->sg_tx_p), GFP_ATOMIC); sg_init_table(dma->sg_tx_p, num); /* Initialize SG table */ /* offset, length setting */ sg = dma->sg_tx_p; @@ -1181,14 +1180,16 @@ static void pch_spi_process_messages(struct work_struct *pwork) data->cur_trans = list_entry(data->current_msg->transfers.next, struct spi_transfer, transfer_list); - dev_dbg(&data->master->dev, "%s " - ":Getting 1st transfer message\n", __func__); + dev_dbg(&data->master->dev, + "%s :Getting 1st transfer message\n", + __func__); } else { data->cur_trans = list_entry(data->cur_trans->transfer_list.next, struct spi_transfer, transfer_list); - dev_dbg(&data->master->dev, "%s " - ":Getting next transfer message\n", __func__); + dev_dbg(&data->master->dev, + "%s :Getting next transfer message\n", + __func__); } spin_unlock(&data->lock); @@ -1233,9 +1234,8 @@ static void pch_spi_process_messages(struct work_struct *pwork) /* check for delay */ if (data->cur_trans->delay_usecs) { - dev_dbg(&data->master->dev, "%s:" - "delay in usec=%d\n", __func__, - data->cur_trans->delay_usecs); + dev_dbg(&data->master->dev, "%s:delay in usec=%d\n", + __func__, data->cur_trans->delay_usecs); udelay(data->cur_trans->delay_usecs); } @@ -1292,7 +1292,6 @@ static void pch_free_dma_buf(struct pch_spi_board_data *board_dat, if (dma->rx_buf_dma) dma_free_coherent(&board_dat->pdev->dev, PCH_BUF_SIZE, dma->rx_buf_virt, dma->rx_buf_dma); - return; } static void pch_alloc_dma_buf(struct pch_spi_board_data *board_dat, @@ -1541,11 +1540,11 @@ static int pch_spi_probe(struct pci_dev *pdev, const struct pci_device_id *id) int i; struct pch_pd_dev_save *pd_dev_save; - pd_dev_save = kzalloc(sizeof(struct pch_pd_dev_save), GFP_KERNEL); + pd_dev_save = kzalloc(sizeof(*pd_dev_save), GFP_KERNEL); if (!pd_dev_save) return -ENOMEM; - board_dat = kzalloc(sizeof(struct pch_spi_board_data), GFP_KERNEL); + board_dat = kzalloc(sizeof(*board_dat), GFP_KERNEL); if (!board_dat) { retval = -ENOMEM; goto err_no_mem; diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 656dd3e3220c..f274df9e0e3e 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -621,8 +621,10 @@ void spi_unregister_device(struct spi_device *spi) if (!spi) return; - if (spi->dev.of_node) + if (spi->dev.of_node) { of_node_clear_flag(spi->dev.of_node, OF_POPULATED); + of_node_put(spi->dev.of_node); + } if (ACPI_COMPANION(&spi->dev)) acpi_device_clear_enumerated(ACPI_COMPANION(&spi->dev)); device_unregister(&spi->dev); @@ -672,7 +674,7 @@ int spi_register_board_info(struct spi_board_info const *info, unsigned n) if (!n) return -EINVAL; - bi = kzalloc(n * sizeof(*bi), GFP_KERNEL); + bi = kcalloc(n, sizeof(*bi), GFP_KERNEL); if (!bi) return -ENOMEM; @@ -805,12 +807,12 @@ static int __spi_map_msg(struct spi_master *master, struct spi_message *msg) if (master->dma_tx) tx_dev = master->dma_tx->device->dev; else - tx_dev = &master->dev; + tx_dev = master->dev.parent; if (master->dma_rx) rx_dev = master->dma_rx->device->dev; else - rx_dev = &master->dev; + rx_dev = master->dev.parent; list_for_each_entry(xfer, &msg->transfers, transfer_list) { if (!master->can_dma(master, msg->spi, xfer)) @@ -852,12 +854,12 @@ static int __spi_unmap_msg(struct spi_master *master, struct spi_message *msg) if (master->dma_tx) tx_dev = master->dma_tx->device->dev; else - tx_dev = &master->dev; + tx_dev = master->dev.parent; if (master->dma_rx) rx_dev = master->dma_rx->device->dev; else - rx_dev = &master->dev; + rx_dev = master->dev.parent; list_for_each_entry(xfer, &msg->transfers, transfer_list) { if (!master->can_dma(master, msg->spi, xfer)) @@ -1502,37 +1504,18 @@ err_init_queue: /*-------------------------------------------------------------------------*/ #if defined(CONFIG_OF) -static struct spi_device * -of_register_spi_device(struct spi_master *master, struct device_node *nc) +static int of_spi_parse_dt(struct spi_master *master, struct spi_device *spi, + struct device_node *nc) { - struct spi_device *spi; - int rc; u32 value; - - /* Alloc an spi_device */ - spi = spi_alloc_device(master); - if (!spi) { - dev_err(&master->dev, "spi_device alloc error for %s\n", - nc->full_name); - rc = -ENOMEM; - goto err_out; - } - - /* Select device driver */ - rc = of_modalias_node(nc, spi->modalias, - sizeof(spi->modalias)); - if (rc < 0) { - dev_err(&master->dev, "cannot find modalias for %s\n", - nc->full_name); - goto err_out; - } + int rc; /* Device address */ rc = of_property_read_u32(nc, "reg", &value); if (rc) { dev_err(&master->dev, "%s has no valid 'reg' property (%d)\n", nc->full_name, rc); - goto err_out; + return rc; } spi->chip_select = value; @@ -1590,10 +1573,41 @@ of_register_spi_device(struct spi_master *master, struct device_node *nc) if (rc) { dev_err(&master->dev, "%s has no valid 'spi-max-frequency' property (%d)\n", nc->full_name, rc); - goto err_out; + return rc; } spi->max_speed_hz = value; + return 0; +} + +static struct spi_device * +of_register_spi_device(struct spi_master *master, struct device_node *nc) +{ + struct spi_device *spi; + int rc; + + /* Alloc an spi_device */ + spi = spi_alloc_device(master); + if (!spi) { + dev_err(&master->dev, "spi_device alloc error for %s\n", + nc->full_name); + rc = -ENOMEM; + goto err_out; + } + + /* Select device driver */ + rc = of_modalias_node(nc, spi->modalias, + sizeof(spi->modalias)); + if (rc < 0) { + dev_err(&master->dev, "cannot find modalias for %s\n", + nc->full_name); + goto err_out; + } + + rc = of_spi_parse_dt(master, spi, nc); + if (rc) + goto err_out; + /* Store a pointer to the node in the device structure */ of_node_get(nc); spi->dev.of_node = nc; @@ -1603,11 +1617,13 @@ of_register_spi_device(struct spi_master *master, struct device_node *nc) if (rc) { dev_err(&master->dev, "spi_device register error %s\n", nc->full_name); - goto err_out; + goto err_of_node_put; } return spi; +err_of_node_put: + of_node_put(nc); err_out: spi_dev_put(spi); return ERR_PTR(rc); diff --git a/include/linux/platform_data/spi-ep93xx.h b/include/linux/platform_data/spi-ep93xx.h index 9bb63ac13f04..171a271c2cbd 100644 --- a/include/linux/platform_data/spi-ep93xx.h +++ b/include/linux/platform_data/spi-ep93xx.h @@ -5,25 +5,14 @@ struct spi_device; /** * struct ep93xx_spi_info - EP93xx specific SPI descriptor - * @num_chipselect: number of chip selects on this board, must be - * at least one + * @chipselect: array of gpio numbers to use as chip selects + * @num_chipselect: ARRAY_SIZE(chipselect) * @use_dma: use DMA for the transfers */ struct ep93xx_spi_info { + int *chipselect; int num_chipselect; bool use_dma; }; -/** - * struct ep93xx_spi_chip_ops - operation callbacks for SPI slave device - * @setup: setup the chip select mechanism - * @cleanup: cleanup the chip select mechanism - * @cs_control: control the device chip select - */ -struct ep93xx_spi_chip_ops { - int (*setup)(struct spi_device *spi); - void (*cleanup)(struct spi_device *spi); - void (*cs_control)(struct spi_device *spi, int value); -}; - #endif /* __ASM_MACH_EP93XX_SPI_H */ diff --git a/include/linux/pxa2xx_ssp.h b/include/linux/pxa2xx_ssp.h index 2d6f0c39ed68..a0522328d7aa 100644 --- a/include/linux/pxa2xx_ssp.h +++ b/include/linux/pxa2xx_ssp.h @@ -90,9 +90,9 @@ #define SSSR_RFL_MASK (0xf << 12) /* Receive FIFO Level mask */ #define SSCR1_TFT (0x000003c0) /* Transmit FIFO Threshold (mask) */ -#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */ +#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */ #define SSCR1_RFT (0x00003c00) /* Receive FIFO Threshold (mask) */ -#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */ +#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */ #define RX_THRESH_CE4100_DFLT 2 #define TX_THRESH_CE4100_DFLT 2 @@ -106,9 +106,9 @@ #define CE4100_SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..4] */ /* QUARK_X1000 SSCR0 bit definition */ -#define QUARK_X1000_SSCR0_DSS (0x1F) /* Data Size Select (mask) */ -#define QUARK_X1000_SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..32] */ -#define QUARK_X1000_SSCR0_FRF (0x3 << 5) /* FRame Format (mask) */ +#define QUARK_X1000_SSCR0_DSS (0x1F << 0) /* Data Size Select (mask) */ +#define QUARK_X1000_SSCR0_DataSize(x) ((x) - 1) /* Data Size Select [4..32] */ +#define QUARK_X1000_SSCR0_FRF (0x3 << 5) /* FRame Format (mask) */ #define QUARK_X1000_SSCR0_Motorola (0x0 << 5) /* Motorola's Serial Peripheral Interface (SPI) */ #define RX_THRESH_QUARK_X1000_DFLT 1 @@ -121,8 +121,8 @@ #define QUARK_X1000_SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..32] */ #define QUARK_X1000_SSCR1_RFT (0x1F << 11) /* Receive FIFO Threshold (mask) */ #define QUARK_X1000_SSCR1_RxTresh(x) (((x) - 1) << 11) /* level [1..32] */ -#define QUARK_X1000_SSCR1_STRF (1 << 17) /* Select FIFO or EFWR */ -#define QUARK_X1000_SSCR1_EFWR (1 << 16) /* Enable FIFO Write/Read */ +#define QUARK_X1000_SSCR1_STRF (1 << 17) /* Select FIFO or EFWR */ +#define QUARK_X1000_SSCR1_EFWR (1 << 16) /* Enable FIFO Write/Read */ /* extra bits in PXA255, PXA26x and PXA27x SSP ports */ #define SSCR0_TISSP (1 << 4) /* TI Sync Serial Protocol */