diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt new file mode 100644 index 000000000000..70c054a9a997 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt @@ -0,0 +1,20 @@ +* Freescale Low Power Inter IC (LPI2C) for i.MX + +Required properties: +- compatible : + - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc + - "fsl,imx8dv-lpi2c" for LPI2C compatible with the one integrated on i.MX8DV soc +- reg : address and length of the lpi2c master registers +- interrupt-parent : core interrupt controller +- interrupts : lpi2c interrupt +- clocks : lpi2c clock specifier + +Examples: + +lpi2c7: lpi2c7@40A50000 { + compatible = "fsl,imx8dv-lpi2c"; + reg = <0x40A50000 0x10000>; + interrupt-parent = <&intc>; + interrupts = ; + clocks = <&clks IMX7ULP_CLK_LPI2C7>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt index 12b78ac507e9..d30f0b11d853 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt @@ -7,6 +7,7 @@ Required properties : compatible processor, e.g. pxa168, pxa910, mmp2, mmp3. For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required as shown in the example below. + For the Armada 3700, the compatible should be "marvell,armada-3700-i2c". Recommended properties : diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt index 239632a0d709..2b8bd33dbf8d 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt @@ -1,17 +1,25 @@ I2C for R-Car platforms Required properties: -- compatible: Must be one of - "renesas,i2c-rcar" - "renesas,i2c-r8a7778" - "renesas,i2c-r8a7779" - "renesas,i2c-r8a7790" - "renesas,i2c-r8a7791" - "renesas,i2c-r8a7792" - "renesas,i2c-r8a7793" - "renesas,i2c-r8a7794" - "renesas,i2c-r8a7795" - "renesas,i2c-r8a7796" +- compatible: + "renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC. + "renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC. + "renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC. + "renesas,i2c-r8a7791" if the device is a part of a R8A7791 SoC. + "renesas,i2c-r8a7792" if the device is a part of a R8A7792 SoC. + "renesas,i2c-r8a7793" if the device is a part of a R8A7793 SoC. + "renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC. + "renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC. + "renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC. + "renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-i2c" for a generic R-Car Gen2 compatible device. + "renesas,rcar-gen3-i2c" for a generic R-Car Gen3 compatible device. + "renesas,i2c-rcar" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + - reg: physical base address of the controller and length of memory mapped region. - interrupts: interrupt specifier. @@ -33,7 +41,7 @@ Examples : i2c0: i2c@e6508000 { #address-cells = <1>; #size-cells = <0>; - compatible = "renesas,i2c-r8a7791"; + compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c"; reg = <0 0xe6508000 0 0x40>; interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7791_CLK_I2C0>; diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt index 214f94c25d37..7716acc55dec 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt @@ -1,8 +1,7 @@ Device tree configuration for Renesas IIC (sh_mobile) driver Required properties: -- compatible : "renesas,iic-". "renesas,rmobile-iic" as fallback - Examples with soctypes are: +- compatible : - "renesas,iic-r8a73a4" (R-Mobile APE6) - "renesas,iic-r8a7740" (R-Mobile A1) - "renesas,iic-r8a7790" (R-Car H2) @@ -12,6 +11,17 @@ Required properties: - "renesas,iic-r8a7794" (R-Car E2) - "renesas,iic-r8a7795" (R-Car H3) - "renesas,iic-sh73a0" (SH-Mobile AG5) + - "renesas,rcar-gen2-iic" (generic R-Car Gen2 compatible device) + - "renesas,rcar-gen3-iic" (generic R-Car Gen3 compatible device) + - "renesas,rmobile-iic" (generic device) + + When compatible with a generic R-Car version, nodes + must list the SoC-specific version corresponding to + the platform first followed by the generic R-Car + version. + + renesas,rmobile-iic must always follow. + - reg : address start and address range size of device - interrupts : interrupt of device - clocks : clock for device @@ -31,7 +41,8 @@ Pinctrl properties might be needed, too. See there. Example: iic0: i2c@e6500000 { - compatible = "renesas,iic-r8a7790", "renesas,rmobile-iic"; + compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic", + "renesas,rmobile-iic"; reg = <0 0xe6500000 0 0x425>; interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_IIC0>; diff --git a/Documentation/i2c/busses/i2c-mlxcpld b/Documentation/i2c/busses/i2c-mlxcpld new file mode 100644 index 000000000000..4e46c440b38d --- /dev/null +++ b/Documentation/i2c/busses/i2c-mlxcpld @@ -0,0 +1,47 @@ +Driver i2c-mlxcpld + +Author: Michael Shych + +This is the Mellanox I2C controller logic, implemented in Lattice CPLD +device. +Device supports: + - Master mode. + - One physical bus. + - Polling mode. + +This controller is equipped within the next Mellanox systems: +"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410", "msb7800", +"msn2740", "msn2100". + +The next transaction types are supported: + - Receive Byte/Block. + - Send Byte/Block. + - Read Byte/Block. + - Write Byte/Block. + +Registers: +CTRL 0x1 - control reg. + Resets all the registers. +HALF_CYC 0x4 - cycle reg. + Configure the width of I2C SCL half clock cycle (in 4 LPC_CLK + units). +I2C_HOLD 0x5 - hold reg. + OE (output enable) is delayed by value set to this register + (in LPC_CLK units) +CMD 0x6 - command reg. + Bit 0, 0 = write, 1 = read. + Bits [7:1] - the 7bit Address of the I2C device. + It should be written last as it triggers an I2C transaction. +NUM_DATA 0x7 - data size reg. + Number of data bytes to write in read transaction +NUM_ADDR 0x8 - address reg. + Number of address bytes to write in read transaction. +STATUS 0x9 - status reg. + Bit 0 - transaction is completed. + Bit 4 - ACK/NACK. +DATAx 0xa - 0x54 - 68 bytes data buffer regs. + For write transaction address is specified in four first bytes + (DATA1 - DATA4), data starting from DATA4. + For read transactions address is sent in a separate transaction and + specified in the four first bytes (DATA0 - DATA3). Data is read + starting from DATA0. diff --git a/Documentation/i2c/smbus-protocol b/Documentation/i2c/smbus-protocol index 14d4ec1be245..092d474f5843 100644 --- a/Documentation/i2c/smbus-protocol +++ b/Documentation/i2c/smbus-protocol @@ -200,10 +200,14 @@ alerting device's address. [S] [HostAddr] [Wr] A [DevAddr] A [DataLow] A [DataHigh] A [P] This is implemented in the following way in the Linux kernel: -* I2C bus drivers which support SMBus Host Notify should call - i2c_setup_smbus_host_notify() to setup SMBus Host Notify support. -* I2C drivers for devices which can trigger SMBus Host Notify should implement - the optional alert() callback. +* I2C bus drivers which support SMBus Host Notify should report + I2C_FUNC_SMBUS_HOST_NOTIFY. +* I2C bus drivers trigger SMBus Host Notify by a call to + i2c_handle_smbus_host_notify(). +* I2C drivers for devices which can trigger SMBus Host Notify will have + client->irq assigned to a Host Notify IRQ if noone else specified an other. + +There is currently no way to retrieve the data parameter from the client. Packet Error Checking (PEC) diff --git a/MAINTAINERS b/MAINTAINERS index 9c481470e277..86f9583393ba 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8023,6 +8023,15 @@ W: http://www.mellanox.com Q: http://patchwork.ozlabs.org/project/netdev/list/ F: drivers/net/ethernet/mellanox/mlxsw/ +MELLANOX MLXCPLD I2C AND MUX DRIVER +M: Vadim Pasternak +M: Michael Shych +L: linux-i2c@vger.kernel.org +S: Supported +F: drivers/i2c/busses/i2c-mlxcpld.c +F: drivers/i2c/muxes/i2c-mux-mlxcpld.c +F: Documentation/i2c/busses/i2c-mlxcpld + MELLANOX MLXCPLD LED DRIVER M: Vadim Pasternak L: linux-leds@vger.kernel.org diff --git a/drivers/i2c/Kconfig b/drivers/i2c/Kconfig index 11edabf425ae..efc3354d60ae 100644 --- a/drivers/i2c/Kconfig +++ b/drivers/i2c/Kconfig @@ -7,6 +7,7 @@ menu "I2C support" config I2C tristate "I2C support" select RT_MUTEXES + select IRQ_DOMAIN ---help--- I2C (pronounce: I-squared-C) is a slow serial bus protocol used in many micro controller applications and developed by Philips. SMBus, diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index d252276feadf..0cdc8443deab 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -426,7 +426,7 @@ config I2C_BLACKFIN_TWI_CLK_KHZ config I2C_CADENCE tristate "Cadence I2C Controller" - depends on ARCH_ZYNQ || ARM64 + depends on ARCH_ZYNQ || ARM64 || XTENSA help Say yes here to select Cadence I2C Host Controller. This controller is e.g. used by Xilinx Zynq. @@ -597,6 +597,16 @@ config I2C_IMX This driver can also be built as a module. If so, the module will be called i2c-imx. +config I2C_IMX_LPI2C + tristate "IMX Low Power I2C interface" + depends on ARCH_MXC || COMPILE_TEST + help + Say Y here if you want to use the Low Power IIC bus controller + on the Freescale i.MX processors. + + This driver can also be built as a module. If so, the module + will be called i2c-imx-lpi2c. + config I2C_IOP3XX tristate "Intel IOPx3xx and IXP4xx on-chip I2C interface" depends on ARCH_IOP32X || ARCH_IOP33X || ARCH_IXP4XX || ARCH_IOP13XX @@ -763,7 +773,7 @@ config I2C_PUV3 config I2C_PXA tristate "Intel PXA2XX I2C adapter" - depends on ARCH_PXA || ARCH_MMP || (X86_32 && PCI && OF) + depends on ARCH_PXA || ARCH_MMP || ARCH_MVEBU || (X86_32 && PCI && OF) help If you have devices in the PXA I2C bus, say yes to this option. This driver can also be built as a module. If so, the module @@ -1150,6 +1160,17 @@ config I2C_ELEKTOR This support is also available as a module. If so, the module will be called i2c-elektor. +config I2C_MLXCPLD + tristate "Mellanox I2C driver" + depends on X86_64 + help + This exposes the Mellanox platform I2C busses to the linux I2C layer + for X86 based systems. + Controller is implemented as CPLD logic. + + This driver can also be built as a module. If so, the module will be + called as i2c-mlxcpld. + config I2C_PCA_ISA tristate "PCA9564/PCA9665 on an ISA bus" depends on ISA diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index 29764cc20a44..1c1bac87a9db 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -56,6 +56,7 @@ obj-$(CONFIG_I2C_HIX5HD2) += i2c-hix5hd2.o obj-$(CONFIG_I2C_IBM_IIC) += i2c-ibm_iic.o obj-$(CONFIG_I2C_IMG) += i2c-img-scb.o obj-$(CONFIG_I2C_IMX) += i2c-imx.o +obj-$(CONFIG_I2C_IMX_LPI2C) += i2c-imx-lpi2c.o obj-$(CONFIG_I2C_IOP3XX) += i2c-iop3xx.o obj-$(CONFIG_I2C_JZ4780) += i2c-jz4780.o obj-$(CONFIG_I2C_KEMPLD) += i2c-kempld.o @@ -116,6 +117,7 @@ obj-$(CONFIG_I2C_BCM_KONA) += i2c-bcm-kona.o obj-$(CONFIG_I2C_BRCMSTB) += i2c-brcmstb.o obj-$(CONFIG_I2C_CROS_EC_TUNNEL) += i2c-cros-ec-tunnel.o obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o +obj-$(CONFIG_I2C_MLXCPLD) += i2c-mlxcpld.o obj-$(CONFIG_I2C_OPAL) += i2c-opal.o obj-$(CONFIG_I2C_PCA_ISA) += i2c-pca-isa.o obj-$(CONFIG_I2C_SIBYTE) += i2c-sibyte.o diff --git a/drivers/i2c/busses/i2c-axxia.c b/drivers/i2c/busses/i2c-axxia.c index 4351a9343058..13f07482ec68 100644 --- a/drivers/i2c/busses/i2c-axxia.c +++ b/drivers/i2c/busses/i2c-axxia.c @@ -489,7 +489,7 @@ static const struct i2c_algorithm axxia_i2c_algo = { .functionality = axxia_i2c_func, }; -static struct i2c_adapter_quirks axxia_i2c_quirks = { +static const struct i2c_adapter_quirks axxia_i2c_quirks = { .max_read_len = 255, .max_write_len = 255, }; diff --git a/drivers/i2c/busses/i2c-bcm-iproc.c b/drivers/i2c/busses/i2c-bcm-iproc.c index 326b3db02c48..318df559adc5 100644 --- a/drivers/i2c/busses/i2c-bcm-iproc.c +++ b/drivers/i2c/busses/i2c-bcm-iproc.c @@ -395,7 +395,7 @@ static const struct i2c_algorithm bcm_iproc_algo = { .functionality = bcm_iproc_i2c_functionality, }; -static struct i2c_adapter_quirks bcm_iproc_i2c_quirks = { +static const struct i2c_adapter_quirks bcm_iproc_i2c_quirks = { /* need to reserve one byte in the FIFO for the slave address */ .max_read_len = M_TX_RX_FIFO_SIZE - 1, }; diff --git a/drivers/i2c/busses/i2c-bcm2835.c b/drivers/i2c/busses/i2c-bcm2835.c index d4f3239b5686..c3436f627028 100644 --- a/drivers/i2c/busses/i2c-bcm2835.c +++ b/drivers/i2c/busses/i2c-bcm2835.c @@ -50,20 +50,19 @@ #define BCM2835_I2C_S_CLKT BIT(9) #define BCM2835_I2C_S_LEN BIT(10) /* Fake bit for SW error reporting */ -#define BCM2835_I2C_BITMSK_S 0x03FF - #define BCM2835_I2C_CDIV_MIN 0x0002 #define BCM2835_I2C_CDIV_MAX 0xFFFE -#define BCM2835_I2C_TIMEOUT (msecs_to_jiffies(1000)) - struct bcm2835_i2c_dev { struct device *dev; void __iomem *regs; struct clk *clk; int irq; + u32 bus_clk_rate; struct i2c_adapter adapter; struct completion completion; + struct i2c_msg *curr_msg; + int num_msgs; u32 msg_err; u8 *msg_buf; size_t msg_buf_remaining; @@ -80,6 +79,30 @@ static inline u32 bcm2835_i2c_readl(struct bcm2835_i2c_dev *i2c_dev, u32 reg) return readl(i2c_dev->regs + reg); } +static int bcm2835_i2c_set_divider(struct bcm2835_i2c_dev *i2c_dev) +{ + u32 divider; + + divider = DIV_ROUND_UP(clk_get_rate(i2c_dev->clk), + i2c_dev->bus_clk_rate); + /* + * Per the datasheet, the register is always interpreted as an even + * number, by rounding down. In other words, the LSB is ignored. So, + * if the LSB is set, increment the divider to avoid any issue. + */ + if (divider & 1) + divider++; + if ((divider < BCM2835_I2C_CDIV_MIN) || + (divider > BCM2835_I2C_CDIV_MAX)) { + dev_err_ratelimited(i2c_dev->dev, "Invalid clock-frequency\n"); + return -EINVAL; + } + + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DIV, divider); + + return 0; +} + static void bcm2835_fill_txfifo(struct bcm2835_i2c_dev *i2c_dev) { u32 val; @@ -110,106 +133,159 @@ static void bcm2835_drain_rxfifo(struct bcm2835_i2c_dev *i2c_dev) } } +/* + * Repeated Start Condition (Sr) + * The BCM2835 ARM Peripherals datasheet mentions a way to trigger a Sr when it + * talks about reading from a slave with 10 bit address. This is achieved by + * issuing a write, poll the I2CS.TA flag and wait for it to be set, and then + * issue a read. + * A comment in https://github.com/raspberrypi/linux/issues/254 shows how the + * firmware actually does it using polling and says that it's a workaround for + * a problem in the state machine. + * It turns out that it is possible to use the TXW interrupt to know when the + * transfer is active, provided the FIFO has not been prefilled. + */ + +static void bcm2835_i2c_start_transfer(struct bcm2835_i2c_dev *i2c_dev) +{ + u32 c = BCM2835_I2C_C_ST | BCM2835_I2C_C_I2CEN; + struct i2c_msg *msg = i2c_dev->curr_msg; + bool last_msg = (i2c_dev->num_msgs == 1); + + if (!i2c_dev->num_msgs) + return; + + i2c_dev->num_msgs--; + i2c_dev->msg_buf = msg->buf; + i2c_dev->msg_buf_remaining = msg->len; + + if (msg->flags & I2C_M_RD) + c |= BCM2835_I2C_C_READ | BCM2835_I2C_C_INTR; + else + c |= BCM2835_I2C_C_INTT; + + if (last_msg) + c |= BCM2835_I2C_C_INTD; + + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_A, msg->addr); + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DLEN, msg->len); + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, c); +} + +/* + * Note about I2C_C_CLEAR on error: + * The I2C_C_CLEAR on errors will take some time to resolve -- if you were in + * non-idle state and I2C_C_READ, it sets an abort_rx flag and runs through + * the state machine to send a NACK and a STOP. Since we're setting CLEAR + * without I2CEN, that NACK will be hanging around queued up for next time + * we start the engine. + */ + static irqreturn_t bcm2835_i2c_isr(int this_irq, void *data) { struct bcm2835_i2c_dev *i2c_dev = data; u32 val, err; val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S); - val &= BCM2835_I2C_BITMSK_S; - bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_S, val); err = val & (BCM2835_I2C_S_CLKT | BCM2835_I2C_S_ERR); if (err) { i2c_dev->msg_err = err; - complete(&i2c_dev->completion); - return IRQ_HANDLED; - } - - if (val & BCM2835_I2C_S_RXD) { - bcm2835_drain_rxfifo(i2c_dev); - if (!(val & BCM2835_I2C_S_DONE)) - return IRQ_HANDLED; + goto complete; } if (val & BCM2835_I2C_S_DONE) { - if (i2c_dev->msg_buf_remaining) + if (i2c_dev->curr_msg->flags & I2C_M_RD) { + bcm2835_drain_rxfifo(i2c_dev); + val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S); + } + + if ((val & BCM2835_I2C_S_RXD) || i2c_dev->msg_buf_remaining) i2c_dev->msg_err = BCM2835_I2C_S_LEN; else i2c_dev->msg_err = 0; - complete(&i2c_dev->completion); + goto complete; + } + + if (val & BCM2835_I2C_S_TXW) { + if (!i2c_dev->msg_buf_remaining) { + i2c_dev->msg_err = val | BCM2835_I2C_S_LEN; + goto complete; + } + + bcm2835_fill_txfifo(i2c_dev); + + if (i2c_dev->num_msgs && !i2c_dev->msg_buf_remaining) { + i2c_dev->curr_msg++; + bcm2835_i2c_start_transfer(i2c_dev); + } + return IRQ_HANDLED; } - if (val & BCM2835_I2C_S_TXD) { - bcm2835_fill_txfifo(i2c_dev); + if (val & BCM2835_I2C_S_RXR) { + if (!i2c_dev->msg_buf_remaining) { + i2c_dev->msg_err = val | BCM2835_I2C_S_LEN; + goto complete; + } + + bcm2835_drain_rxfifo(i2c_dev); return IRQ_HANDLED; } return IRQ_NONE; -} - -static int bcm2835_i2c_xfer_msg(struct bcm2835_i2c_dev *i2c_dev, - struct i2c_msg *msg) -{ - u32 c; - unsigned long time_left; - - i2c_dev->msg_buf = msg->buf; - i2c_dev->msg_buf_remaining = msg->len; - reinit_completion(&i2c_dev->completion); +complete: bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, BCM2835_I2C_C_CLEAR); + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_S, BCM2835_I2C_S_CLKT | + BCM2835_I2C_S_ERR | BCM2835_I2C_S_DONE); + complete(&i2c_dev->completion); - if (msg->flags & I2C_M_RD) { - c = BCM2835_I2C_C_READ | BCM2835_I2C_C_INTR; - } else { - c = BCM2835_I2C_C_INTT; - bcm2835_fill_txfifo(i2c_dev); - } - c |= BCM2835_I2C_C_ST | BCM2835_I2C_C_INTD | BCM2835_I2C_C_I2CEN; - - bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_A, msg->addr); - bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DLEN, msg->len); - bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, c); - - time_left = wait_for_completion_timeout(&i2c_dev->completion, - BCM2835_I2C_TIMEOUT); - bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, BCM2835_I2C_C_CLEAR); - if (!time_left) { - dev_err(i2c_dev->dev, "i2c transfer timed out\n"); - return -ETIMEDOUT; - } - - if (likely(!i2c_dev->msg_err)) - return 0; - - if ((i2c_dev->msg_err & BCM2835_I2C_S_ERR) && - (msg->flags & I2C_M_IGNORE_NAK)) - return 0; - - dev_err(i2c_dev->dev, "i2c transfer failed: %x\n", i2c_dev->msg_err); - - if (i2c_dev->msg_err & BCM2835_I2C_S_ERR) - return -EREMOTEIO; - else - return -EIO; + return IRQ_HANDLED; } static int bcm2835_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) { struct bcm2835_i2c_dev *i2c_dev = i2c_get_adapdata(adap); - int i; - int ret = 0; + unsigned long time_left; + int i, ret; - for (i = 0; i < num; i++) { - ret = bcm2835_i2c_xfer_msg(i2c_dev, &msgs[i]); - if (ret) - break; + for (i = 0; i < (num - 1); i++) + if (msgs[i].flags & I2C_M_RD) { + dev_warn_once(i2c_dev->dev, + "only one read message supported, has to be last\n"); + return -EOPNOTSUPP; + } + + ret = bcm2835_i2c_set_divider(i2c_dev); + if (ret) + return ret; + + i2c_dev->curr_msg = msgs; + i2c_dev->num_msgs = num; + reinit_completion(&i2c_dev->completion); + + bcm2835_i2c_start_transfer(i2c_dev); + + time_left = wait_for_completion_timeout(&i2c_dev->completion, + adap->timeout); + if (!time_left) { + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, + BCM2835_I2C_C_CLEAR); + dev_err(i2c_dev->dev, "i2c transfer timed out\n"); + return -ETIMEDOUT; } - return ret ?: i; + if (!i2c_dev->msg_err) + return num; + + dev_dbg(i2c_dev->dev, "i2c transfer failed: %x\n", i2c_dev->msg_err); + + if (i2c_dev->msg_err & BCM2835_I2C_S_ERR) + return -EREMOTEIO; + + return -EIO; } static u32 bcm2835_i2c_func(struct i2c_adapter *adap) @@ -235,7 +311,6 @@ static int bcm2835_i2c_probe(struct platform_device *pdev) { struct bcm2835_i2c_dev *i2c_dev; struct resource *mem, *irq; - u32 bus_clk_rate, divider; int ret; struct i2c_adapter *adap; @@ -259,28 +334,13 @@ static int bcm2835_i2c_probe(struct platform_device *pdev) } ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency", - &bus_clk_rate); + &i2c_dev->bus_clk_rate); if (ret < 0) { dev_warn(&pdev->dev, "Could not read clock-frequency property\n"); - bus_clk_rate = 100000; + i2c_dev->bus_clk_rate = 100000; } - divider = DIV_ROUND_UP(clk_get_rate(i2c_dev->clk), bus_clk_rate); - /* - * Per the datasheet, the register is always interpreted as an even - * number, by rounding down. In other words, the LSB is ignored. So, - * if the LSB is set, increment the divider to avoid any issue. - */ - if (divider & 1) - divider++; - if ((divider < BCM2835_I2C_CDIV_MIN) || - (divider > BCM2835_I2C_CDIV_MAX)) { - dev_err(&pdev->dev, "Invalid clock-frequency\n"); - return -ENODEV; - } - bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DIV, divider); - irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); if (!irq) { dev_err(&pdev->dev, "No IRQ resource\n"); diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index b403fa5ecf49..6d81c56184d3 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -536,6 +536,8 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) intr_mask = DW_IC_INTR_DEFAULT_MASK; for (; dev->msg_write_idx < dev->msgs_num; dev->msg_write_idx++) { + u32 flags = msgs[dev->msg_write_idx].flags; + /* * if target address has changed, we need to * reprogram the target address in the i2c @@ -581,8 +583,15 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) * detected from the registers so we set it always * when writing/reading the last byte. */ + + /* + * i2c-core.c always sets the buffer length of + * I2C_FUNC_SMBUS_BLOCK_DATA to 1. The length will + * be adjusted when receiving the first byte. + * Thus we can't stop the transaction here. + */ if (dev->msg_write_idx == dev->msgs_num - 1 && - buf_len == 1) + buf_len == 1 && !(flags & I2C_M_RECV_LEN)) cmd |= BIT(9); if (need_restart) { @@ -607,7 +616,12 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) dev->tx_buf = buf; dev->tx_buf_len = buf_len; - if (buf_len > 0) { + /* + * Because we don't know the buffer length in the + * I2C_FUNC_SMBUS_BLOCK_DATA case, we can't stop + * the transaction here. + */ + if (buf_len > 0 || flags & I2C_M_RECV_LEN) { /* more bytes to be written */ dev->status |= STATUS_WRITE_IN_PROGRESS; break; @@ -628,6 +642,24 @@ i2c_dw_xfer_msg(struct dw_i2c_dev *dev) dw_writel(dev, intr_mask, DW_IC_INTR_MASK); } +static u8 +i2c_dw_recv_len(struct dw_i2c_dev *dev, u8 len) +{ + struct i2c_msg *msgs = dev->msgs; + u32 flags = msgs[dev->msg_read_idx].flags; + + /* + * Adjust the buffer length and mask the flag + * after receiving the first byte. + */ + len += (flags & I2C_CLIENT_PEC) ? 2 : 1; + dev->tx_buf_len = len - min_t(u8, len, dev->rx_outstanding); + msgs[dev->msg_read_idx].len = len; + msgs[dev->msg_read_idx].flags &= ~I2C_M_RECV_LEN; + + return len; +} + static void i2c_dw_read(struct dw_i2c_dev *dev) { @@ -652,7 +684,15 @@ i2c_dw_read(struct dw_i2c_dev *dev) rx_valid = dw_readl(dev, DW_IC_RXFLR); for (; len > 0 && rx_valid > 0; len--, rx_valid--) { - *buf++ = dw_readl(dev, DW_IC_DATA_CMD); + u32 flags = msgs[dev->msg_read_idx].flags; + + *buf = dw_readl(dev, DW_IC_DATA_CMD); + /* Ensure length byte is a valid value */ + if (flags & I2C_M_RECV_LEN && + *buf <= I2C_SMBUS_BLOCK_MAX && *buf > 0) { + len = i2c_dw_recv_len(dev, *buf); + } + buf++; dev->rx_outstanding--; } diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index 0d44d2ae7d4c..26250b425e2f 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -22,6 +22,14 @@ * */ +#include + +#define DW_IC_DEFAULT_FUNCTIONALITY (I2C_FUNC_I2C | \ + I2C_FUNC_SMBUS_BYTE | \ + I2C_FUNC_SMBUS_BYTE_DATA | \ + I2C_FUNC_SMBUS_WORD_DATA | \ + I2C_FUNC_SMBUS_BLOCK_DATA | \ + I2C_FUNC_SMBUS_I2C_BLOCK) #define DW_IC_CON_MASTER 0x1 #define DW_IC_CON_SPEED_STD 0x2 diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c index 96f8230cd2d3..d6423cfac588 100644 --- a/drivers/i2c/busses/i2c-designware-pcidrv.c +++ b/drivers/i2c/busses/i2c-designware-pcidrv.c @@ -71,12 +71,6 @@ struct dw_pci_controller { DW_IC_CON_SLAVE_DISABLE | \ DW_IC_CON_RESTART_EN) -#define DW_DEFAULT_FUNCTIONALITY (I2C_FUNC_I2C | \ - I2C_FUNC_SMBUS_BYTE | \ - I2C_FUNC_SMBUS_BYTE_DATA | \ - I2C_FUNC_SMBUS_WORD_DATA | \ - I2C_FUNC_SMBUS_I2C_BLOCK) - /* Merrifield HCNT/LCNT/SDA hold time */ static struct dw_scl_sda_cfg mrfld_config = { .ss_hcnt = 0x2f8, @@ -147,6 +141,7 @@ static struct dw_pci_controller dw_pci_controllers[] = { .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, .tx_fifo_depth = 32, .rx_fifo_depth = 32, + .functionality = I2C_FUNC_10BIT_ADDR, .clk_khz = 25000, .setup = mfld_setup, }, @@ -155,6 +150,7 @@ static struct dw_pci_controller dw_pci_controllers[] = { .bus_cfg = INTEL_MID_STD_CFG | DW_IC_CON_SPEED_FAST, .tx_fifo_depth = 64, .rx_fifo_depth = 64, + .functionality = I2C_FUNC_10BIT_ADDR, .scl_sda_cfg = &mrfld_config, .setup = mrfld_setup, }, @@ -249,7 +245,7 @@ static int i2c_dw_pci_probe(struct pci_dev *pdev, } dev->functionality = controller->functionality | - DW_DEFAULT_FUNCTIONALITY; + DW_IC_DEFAULT_FUNCTIONALITY; dev->master_cfg = controller->bus_cfg; if (controller->scl_sda_cfg) { diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index 0b42a12171f3..08153ea4d848 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -176,9 +176,6 @@ static int dw_i2c_plat_probe(struct platform_device *pdev) dev->irq = irq; platform_set_drvdata(pdev, dev); - /* fast mode by default because of legacy reasons */ - dev->clk_freq = 400000; - if (pdata) { dev->clk_freq = pdata->i2c_scl_freq; } else { @@ -193,8 +190,16 @@ static int dw_i2c_plat_probe(struct platform_device *pdev) } acpi_speed = i2c_acpi_find_bus_speed(&pdev->dev); - if (acpi_speed) - dev->clk_freq = acpi_speed; + /* + * Find bus speed from the "clock-frequency" device property, ACPI + * or by using fast mode if neither is set. + */ + if (acpi_speed && dev->clk_freq) + dev->clk_freq = min(dev->clk_freq, acpi_speed); + else if (acpi_speed || dev->clk_freq) + dev->clk_freq = max(dev->clk_freq, acpi_speed); + else + dev->clk_freq = 400000; if (has_acpi_companion(&pdev->dev)) dw_i2c_acpi_configure(pdev); @@ -214,13 +219,7 @@ static int dw_i2c_plat_probe(struct platform_device *pdev) if (r) return r; - dev->functionality = - I2C_FUNC_I2C | - I2C_FUNC_10BIT_ADDR | - I2C_FUNC_SMBUS_BYTE | - I2C_FUNC_SMBUS_BYTE_DATA | - I2C_FUNC_SMBUS_WORD_DATA | - I2C_FUNC_SMBUS_I2C_BLOCK; + dev->functionality = I2C_FUNC_10BIT_ADDR | DW_IC_DEFAULT_FUNCTIONALITY; dev->master_cfg = DW_IC_CON_MASTER | DW_IC_CON_SLAVE_DISABLE | DW_IC_CON_RESTART_EN; diff --git a/drivers/i2c/busses/i2c-dln2.c b/drivers/i2c/busses/i2c-dln2.c index 8acda2aa1558..69075a32073e 100644 --- a/drivers/i2c/busses/i2c-dln2.c +++ b/drivers/i2c/busses/i2c-dln2.c @@ -182,7 +182,7 @@ static const struct i2c_algorithm dln2_i2c_usb_algorithm = { .functionality = dln2_i2c_func, }; -static struct i2c_adapter_quirks dln2_i2c_quirks = { +static const struct i2c_adapter_quirks dln2_i2c_quirks = { .max_read_len = DLN2_I2C_MAX_XFER_SIZE, .max_write_len = DLN2_I2C_MAX_XFER_SIZE, }; diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index eb3627f35d12..e242db43774b 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -118,7 +118,6 @@ #define SMBSLVSTS(p) (16 + (p)->smba) /* ICH3 and later */ #define SMBSLVCMD(p) (17 + (p)->smba) /* ICH3 and later */ #define SMBNTFDADD(p) (20 + (p)->smba) /* ICH3 and later */ -#define SMBNTFDDAT(p) (22 + (p)->smba) /* ICH3 and later */ /* PCI Address Constants */ #define SMBBAR 4 @@ -137,27 +136,27 @@ #define SBREG_SMBCTRL 0xc6000c /* Host status bits for SMBPCISTS */ -#define SMBPCISTS_INTS 0x08 +#define SMBPCISTS_INTS BIT(3) /* Control bits for SMBPCICTL */ -#define SMBPCICTL_INTDIS 0x0400 +#define SMBPCICTL_INTDIS BIT(10) /* Host configuration bits for SMBHSTCFG */ -#define SMBHSTCFG_HST_EN 1 -#define SMBHSTCFG_SMB_SMI_EN 2 -#define SMBHSTCFG_I2C_EN 4 -#define SMBHSTCFG_SPD_WD 0x10 +#define SMBHSTCFG_HST_EN BIT(0) +#define SMBHSTCFG_SMB_SMI_EN BIT(1) +#define SMBHSTCFG_I2C_EN BIT(2) +#define SMBHSTCFG_SPD_WD BIT(4) /* TCO configuration bits for TCOCTL */ -#define TCOCTL_EN 0x0100 +#define TCOCTL_EN BIT(8) /* Auxiliary status register bits, ICH4+ only */ -#define SMBAUXSTS_CRCE 1 -#define SMBAUXSTS_STCO 2 +#define SMBAUXSTS_CRCE BIT(0) +#define SMBAUXSTS_STCO BIT(1) /* Auxiliary control register bits, ICH4+ only */ -#define SMBAUXCTL_CRC 1 -#define SMBAUXCTL_E32B 2 +#define SMBAUXCTL_CRC BIT(0) +#define SMBAUXCTL_E32B BIT(1) /* Other settings */ #define MAX_RETRIES 400 @@ -172,27 +171,27 @@ #define I801_I2C_BLOCK_DATA 0x18 /* ICH5 and later */ /* I801 Host Control register bits */ -#define SMBHSTCNT_INTREN 0x01 -#define SMBHSTCNT_KILL 0x02 -#define SMBHSTCNT_LAST_BYTE 0x20 -#define SMBHSTCNT_START 0x40 -#define SMBHSTCNT_PEC_EN 0x80 /* ICH3 and later */ +#define SMBHSTCNT_INTREN BIT(0) +#define SMBHSTCNT_KILL BIT(1) +#define SMBHSTCNT_LAST_BYTE BIT(5) +#define SMBHSTCNT_START BIT(6) +#define SMBHSTCNT_PEC_EN BIT(7) /* ICH3 and later */ /* I801 Hosts Status register bits */ -#define SMBHSTSTS_BYTE_DONE 0x80 -#define SMBHSTSTS_INUSE_STS 0x40 -#define SMBHSTSTS_SMBALERT_STS 0x20 -#define SMBHSTSTS_FAILED 0x10 -#define SMBHSTSTS_BUS_ERR 0x08 -#define SMBHSTSTS_DEV_ERR 0x04 -#define SMBHSTSTS_INTR 0x02 -#define SMBHSTSTS_HOST_BUSY 0x01 +#define SMBHSTSTS_BYTE_DONE BIT(7) +#define SMBHSTSTS_INUSE_STS BIT(6) +#define SMBHSTSTS_SMBALERT_STS BIT(5) +#define SMBHSTSTS_FAILED BIT(4) +#define SMBHSTSTS_BUS_ERR BIT(3) +#define SMBHSTSTS_DEV_ERR BIT(2) +#define SMBHSTSTS_INTR BIT(1) +#define SMBHSTSTS_HOST_BUSY BIT(0) -/* Host Notify Status registers bits */ -#define SMBSLVSTS_HST_NTFY_STS 1 +/* Host Notify Status register bits */ +#define SMBSLVSTS_HST_NTFY_STS BIT(0) -/* Host Notify Command registers bits */ -#define SMBSLVCMD_HST_NTFY_INTREN 0x01 +/* Host Notify Command register bits */ +#define SMBSLVCMD_HST_NTFY_INTREN BIT(0) #define STATUS_ERROR_FLAGS (SMBHSTSTS_FAILED | SMBHSTSTS_BUS_ERR | \ SMBHSTSTS_DEV_ERR) @@ -243,6 +242,7 @@ struct i801_priv { struct i2c_adapter adapter; unsigned long smba; unsigned char original_hstcfg; + unsigned char original_slvcmd; struct pci_dev *pci_dev; unsigned int features; @@ -269,20 +269,17 @@ struct i801_priv { */ bool acpi_reserved; struct mutex acpi_lock; - struct smbus_host_notify *host_notify; }; -#define SMBHSTNTFY_SIZE 8 - -#define FEATURE_SMBUS_PEC (1 << 0) -#define FEATURE_BLOCK_BUFFER (1 << 1) -#define FEATURE_BLOCK_PROC (1 << 2) -#define FEATURE_I2C_BLOCK_READ (1 << 3) -#define FEATURE_IRQ (1 << 4) -#define FEATURE_HOST_NOTIFY (1 << 5) +#define FEATURE_SMBUS_PEC BIT(0) +#define FEATURE_BLOCK_BUFFER BIT(1) +#define FEATURE_BLOCK_PROC BIT(2) +#define FEATURE_I2C_BLOCK_READ BIT(3) +#define FEATURE_IRQ BIT(4) +#define FEATURE_HOST_NOTIFY BIT(5) /* Not really a feature, but it's convenient to handle it as such */ -#define FEATURE_IDF (1 << 15) -#define FEATURE_TCO (1 << 16) +#define FEATURE_IDF BIT(15) +#define FEATURE_TCO BIT(16) static const char *i801_feature_names[] = { "SMBus PEC", @@ -582,12 +579,15 @@ static void i801_isr_byte_done(struct i801_priv *priv) static irqreturn_t i801_host_notify_isr(struct i801_priv *priv) { unsigned short addr; - unsigned int data; addr = inb_p(SMBNTFDADD(priv)) >> 1; - data = inw_p(SMBNTFDDAT(priv)); - i2c_handle_smbus_host_notify(priv->host_notify, addr, data); + /* + * With the tested platforms, reading SMBNTFDDAT (22 + (p)->smba) + * always returns 0. Our current implementation doesn't provide + * data, so we just ignore it. + */ + i2c_handle_smbus_host_notify(&priv->adapter, addr); /* clear Host Notify bit and return */ outb_p(SMBSLVSTS_HST_NTFY_STS, SMBSLVSTS(priv)); @@ -950,23 +950,29 @@ static u32 i801_func(struct i2c_adapter *adapter) I2C_FUNC_SMBUS_HOST_NOTIFY : 0); } -static int i801_enable_host_notify(struct i2c_adapter *adapter) +static void i801_enable_host_notify(struct i2c_adapter *adapter) { struct i801_priv *priv = i2c_get_adapdata(adapter); if (!(priv->features & FEATURE_HOST_NOTIFY)) - return -ENOTSUPP; + return; - if (!priv->host_notify) - priv->host_notify = i2c_setup_smbus_host_notify(adapter); - if (!priv->host_notify) - return -ENOMEM; + priv->original_slvcmd = inb_p(SMBSLVCMD(priv)); + + if (!(SMBSLVCMD_HST_NTFY_INTREN & priv->original_slvcmd)) + outb_p(SMBSLVCMD_HST_NTFY_INTREN | priv->original_slvcmd, + SMBSLVCMD(priv)); - outb_p(SMBSLVCMD_HST_NTFY_INTREN, SMBSLVCMD(priv)); /* clear Host Notify bit to allow a new notification */ outb_p(SMBSLVSTS_HST_NTFY_STS, SMBSLVSTS(priv)); +} - return 0; +static void i801_disable_host_notify(struct i801_priv *priv) +{ + if (!(priv->features & FEATURE_HOST_NOTIFY)) + return; + + outb_p(priv->original_slvcmd, SMBSLVCMD(priv)); } static const struct i2c_algorithm smbus_algorithm = { @@ -1633,14 +1639,7 @@ static int i801_probe(struct pci_dev *dev, const struct pci_device_id *id) return err; } - /* - * Enable Host Notify for chips that supports it. - * It is done after i2c_add_adapter() so that we are sure the work queue - * is not used if i2c_add_adapter() fails. - */ - err = i801_enable_host_notify(&priv->adapter); - if (err && err != -ENOTSUPP) - dev_warn(&dev->dev, "Unable to enable SMBus Host Notify\n"); + i801_enable_host_notify(&priv->adapter); i801_probe_optional_slaves(priv); /* We ignore errors - multiplexing is optional */ @@ -1663,6 +1662,7 @@ static void i801_remove(struct pci_dev *dev) pm_runtime_forbid(&dev->dev); pm_runtime_get_noresume(&dev->dev); + i801_disable_host_notify(priv); i801_del_mux(priv); i2c_del_adapter(&priv->adapter); i801_acpi_remove(priv); @@ -1690,11 +1690,8 @@ static int i801_resume(struct device *dev) { struct pci_dev *pci_dev = to_pci_dev(dev); struct i801_priv *priv = pci_get_drvdata(pci_dev); - int err; - err = i801_enable_host_notify(&priv->adapter); - if (err && err != -ENOTSUPP) - dev_warn(dev, "Unable to enable SMBus Host Notify\n"); + i801_enable_host_notify(&priv->adapter); return 0; } diff --git a/drivers/i2c/busses/i2c-imx-lpi2c.c b/drivers/i2c/busses/i2c-imx-lpi2c.c new file mode 100644 index 000000000000..c62b7cd475f8 --- /dev/null +++ b/drivers/i2c/busses/i2c-imx-lpi2c.c @@ -0,0 +1,652 @@ +/* + * This is i.MX low power i2c controller driver. + * + * Copyright 2016 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRIVER_NAME "imx-lpi2c" + +#define LPI2C_PARAM 0x04 /* i2c RX/TX FIFO size */ +#define LPI2C_MCR 0x10 /* i2c contrl register */ +#define LPI2C_MSR 0x14 /* i2c status register */ +#define LPI2C_MIER 0x18 /* i2c interrupt enable */ +#define LPI2C_MCFGR0 0x20 /* i2c master configuration */ +#define LPI2C_MCFGR1 0x24 /* i2c master configuration */ +#define LPI2C_MCFGR2 0x28 /* i2c master configuration */ +#define LPI2C_MCFGR3 0x2C /* i2c master configuration */ +#define LPI2C_MCCR0 0x48 /* i2c master clk configuration */ +#define LPI2C_MCCR1 0x50 /* i2c master clk configuration */ +#define LPI2C_MFCR 0x58 /* i2c master FIFO control */ +#define LPI2C_MFSR 0x5C /* i2c master FIFO status */ +#define LPI2C_MTDR 0x60 /* i2c master TX data register */ +#define LPI2C_MRDR 0x70 /* i2c master RX data register */ + +/* i2c command */ +#define TRAN_DATA 0X00 +#define RECV_DATA 0X01 +#define GEN_STOP 0X02 +#define RECV_DISCARD 0X03 +#define GEN_START 0X04 +#define START_NACK 0X05 +#define START_HIGH 0X06 +#define START_HIGH_NACK 0X07 + +#define MCR_MEN BIT(0) +#define MCR_RST BIT(1) +#define MCR_DOZEN BIT(2) +#define MCR_DBGEN BIT(3) +#define MCR_RTF BIT(8) +#define MCR_RRF BIT(9) +#define MSR_TDF BIT(0) +#define MSR_RDF BIT(1) +#define MSR_SDF BIT(9) +#define MSR_NDF BIT(10) +#define MSR_ALF BIT(11) +#define MSR_MBF BIT(24) +#define MSR_BBF BIT(25) +#define MIER_TDIE BIT(0) +#define MIER_RDIE BIT(1) +#define MIER_SDIE BIT(9) +#define MIER_NDIE BIT(10) +#define MCFGR1_AUTOSTOP BIT(8) +#define MCFGR1_IGNACK BIT(9) +#define MRDR_RXEMPTY BIT(14) + +#define I2C_CLK_RATIO 2 +#define CHUNK_DATA 256 + +#define LPI2C_DEFAULT_RATE 100000 +#define STARDARD_MAX_BITRATE 400000 +#define FAST_MAX_BITRATE 1000000 +#define FAST_PLUS_MAX_BITRATE 3400000 +#define HIGHSPEED_MAX_BITRATE 5000000 + +enum lpi2c_imx_mode { + STANDARD, /* 100+Kbps */ + FAST, /* 400+Kbps */ + FAST_PLUS, /* 1.0+Mbps */ + HS, /* 3.4+Mbps */ + ULTRA_FAST, /* 5.0+Mbps */ +}; + +enum lpi2c_imx_pincfg { + TWO_PIN_OD, + TWO_PIN_OO, + TWO_PIN_PP, + FOUR_PIN_PP, +}; + +struct lpi2c_imx_struct { + struct i2c_adapter adapter; + struct clk *clk; + void __iomem *base; + __u8 *rx_buf; + __u8 *tx_buf; + struct completion complete; + unsigned int msglen; + unsigned int delivered; + unsigned int block_data; + unsigned int bitrate; + unsigned int txfifosize; + unsigned int rxfifosize; + enum lpi2c_imx_mode mode; +}; + +static void lpi2c_imx_intctrl(struct lpi2c_imx_struct *lpi2c_imx, + unsigned int enable) +{ + writel(enable, lpi2c_imx->base + LPI2C_MIER); +} + +static int lpi2c_imx_bus_busy(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned long orig_jiffies = jiffies; + unsigned int temp; + + while (1) { + temp = readl(lpi2c_imx->base + LPI2C_MSR); + + /* check for arbitration lost, clear if set */ + if (temp & MSR_ALF) { + writel(temp, lpi2c_imx->base + LPI2C_MSR); + return -EAGAIN; + } + + if (temp & (MSR_BBF | MSR_MBF)) + break; + + if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) { + dev_dbg(&lpi2c_imx->adapter.dev, "bus not work\n"); + return -ETIMEDOUT; + } + schedule(); + } + + return 0; +} + +static void lpi2c_imx_set_mode(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned int bitrate = lpi2c_imx->bitrate; + enum lpi2c_imx_mode mode; + + if (bitrate < STARDARD_MAX_BITRATE) + mode = STANDARD; + else if (bitrate < FAST_MAX_BITRATE) + mode = FAST; + else if (bitrate < FAST_PLUS_MAX_BITRATE) + mode = FAST_PLUS; + else if (bitrate < HIGHSPEED_MAX_BITRATE) + mode = HS; + else + mode = ULTRA_FAST; + + lpi2c_imx->mode = mode; +} + +static int lpi2c_imx_start(struct lpi2c_imx_struct *lpi2c_imx, + struct i2c_msg *msgs) +{ + unsigned int temp; + u8 read; + + temp = readl(lpi2c_imx->base + LPI2C_MCR); + temp |= MCR_RRF | MCR_RTF; + writel(temp, lpi2c_imx->base + LPI2C_MCR); + writel(0x7f00, lpi2c_imx->base + LPI2C_MSR); + + read = msgs->flags & I2C_M_RD; + temp = (msgs->addr << 1 | read) | (GEN_START << 8); + writel(temp, lpi2c_imx->base + LPI2C_MTDR); + + return lpi2c_imx_bus_busy(lpi2c_imx); +} + +static void lpi2c_imx_stop(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned long orig_jiffies = jiffies; + unsigned int temp; + + writel(GEN_STOP << 8, lpi2c_imx->base + LPI2C_MTDR); + + do { + temp = readl(lpi2c_imx->base + LPI2C_MSR); + if (temp & MSR_SDF) + break; + + if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) { + dev_dbg(&lpi2c_imx->adapter.dev, "stop timeout\n"); + break; + } + schedule(); + + } while (1); +} + +/* CLKLO = I2C_CLK_RATIO * CLKHI, SETHOLD = CLKHI, DATAVD = CLKHI/2 */ +static int lpi2c_imx_config(struct lpi2c_imx_struct *lpi2c_imx) +{ + u8 prescale, filt, sethold, clkhi, clklo, datavd; + unsigned int clk_rate, clk_cycle; + enum lpi2c_imx_pincfg pincfg; + unsigned int temp; + + lpi2c_imx_set_mode(lpi2c_imx); + + clk_rate = clk_get_rate(lpi2c_imx->clk); + if (lpi2c_imx->mode == HS || lpi2c_imx->mode == ULTRA_FAST) + filt = 0; + else + filt = 2; + + for (prescale = 0; prescale <= 7; prescale++) { + clk_cycle = clk_rate / ((1 << prescale) * lpi2c_imx->bitrate) + - 3 - (filt >> 1); + clkhi = (clk_cycle + I2C_CLK_RATIO) / (I2C_CLK_RATIO + 1); + clklo = clk_cycle - clkhi; + if (clklo < 64) + break; + } + + if (prescale > 7) + return -EINVAL; + + /* set MCFGR1: PINCFG, PRESCALE, IGNACK */ + if (lpi2c_imx->mode == ULTRA_FAST) + pincfg = TWO_PIN_OO; + else + pincfg = TWO_PIN_OD; + temp = prescale | pincfg << 24; + + if (lpi2c_imx->mode == ULTRA_FAST) + temp |= MCFGR1_IGNACK; + + writel(temp, lpi2c_imx->base + LPI2C_MCFGR1); + + /* set MCFGR2: FILTSDA, FILTSCL */ + temp = (filt << 16) | (filt << 24); + writel(temp, lpi2c_imx->base + LPI2C_MCFGR2); + + /* set MCCR: DATAVD, SETHOLD, CLKHI, CLKLO */ + sethold = clkhi; + datavd = clkhi >> 1; + temp = datavd << 24 | sethold << 16 | clkhi << 8 | clklo; + + if (lpi2c_imx->mode == HS) + writel(temp, lpi2c_imx->base + LPI2C_MCCR1); + else + writel(temp, lpi2c_imx->base + LPI2C_MCCR0); + + return 0; +} + +static int lpi2c_imx_master_enable(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned int temp; + int ret; + + ret = clk_enable(lpi2c_imx->clk); + if (ret) + return ret; + + temp = MCR_RST; + writel(temp, lpi2c_imx->base + LPI2C_MCR); + writel(0, lpi2c_imx->base + LPI2C_MCR); + + ret = lpi2c_imx_config(lpi2c_imx); + if (ret) + goto clk_disable; + + temp = readl(lpi2c_imx->base + LPI2C_MCR); + temp |= MCR_MEN; + writel(temp, lpi2c_imx->base + LPI2C_MCR); + + return 0; + +clk_disable: + clk_disable(lpi2c_imx->clk); + + return ret; +} + +static int lpi2c_imx_master_disable(struct lpi2c_imx_struct *lpi2c_imx) +{ + u32 temp; + + temp = readl(lpi2c_imx->base + LPI2C_MCR); + temp &= ~MCR_MEN; + writel(temp, lpi2c_imx->base + LPI2C_MCR); + + clk_disable(lpi2c_imx->clk); + + return 0; +} + +static int lpi2c_imx_msg_complete(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned long timeout; + + timeout = wait_for_completion_timeout(&lpi2c_imx->complete, HZ); + + return timeout ? 0 : -ETIMEDOUT; +} + +static int lpi2c_imx_txfifo_empty(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned long orig_jiffies = jiffies; + u32 txcnt; + + do { + txcnt = readl(lpi2c_imx->base + LPI2C_MFSR) & 0xff; + + if (readl(lpi2c_imx->base + LPI2C_MSR) & MSR_NDF) { + dev_dbg(&lpi2c_imx->adapter.dev, "NDF detected\n"); + return -EIO; + } + + if (time_after(jiffies, orig_jiffies + msecs_to_jiffies(500))) { + dev_dbg(&lpi2c_imx->adapter.dev, "txfifo empty timeout\n"); + return -ETIMEDOUT; + } + schedule(); + + } while (txcnt); + + return 0; +} + +static void lpi2c_imx_set_tx_watermark(struct lpi2c_imx_struct *lpi2c_imx) +{ + writel(lpi2c_imx->txfifosize >> 1, lpi2c_imx->base + LPI2C_MFCR); +} + +static void lpi2c_imx_set_rx_watermark(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned int temp, remaining; + + remaining = lpi2c_imx->msglen - lpi2c_imx->delivered; + + if (remaining > (lpi2c_imx->rxfifosize >> 1)) + temp = lpi2c_imx->rxfifosize >> 1; + else + temp = 0; + + writel(temp << 16, lpi2c_imx->base + LPI2C_MFCR); +} + +static void lpi2c_imx_write_txfifo(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned int data, txcnt; + + txcnt = readl(lpi2c_imx->base + LPI2C_MFSR) & 0xff; + + while (txcnt < lpi2c_imx->txfifosize) { + if (lpi2c_imx->delivered == lpi2c_imx->msglen) + break; + + data = lpi2c_imx->tx_buf[lpi2c_imx->delivered++]; + writel(data, lpi2c_imx->base + LPI2C_MTDR); + txcnt++; + } + + if (lpi2c_imx->delivered < lpi2c_imx->msglen) + lpi2c_imx_intctrl(lpi2c_imx, MIER_TDIE | MIER_NDIE); + else + complete(&lpi2c_imx->complete); +} + +static void lpi2c_imx_read_rxfifo(struct lpi2c_imx_struct *lpi2c_imx) +{ + unsigned int blocklen, remaining; + unsigned int temp, data; + + do { + data = readl(lpi2c_imx->base + LPI2C_MRDR); + if (data & MRDR_RXEMPTY) + break; + + lpi2c_imx->rx_buf[lpi2c_imx->delivered++] = data & 0xff; + } while (1); + + /* + * First byte is the length of remaining packet in the SMBus block + * data read. Add it to msgs->len. + */ + if (lpi2c_imx->block_data) { + blocklen = lpi2c_imx->rx_buf[0]; + lpi2c_imx->msglen += blocklen; + } + + remaining = lpi2c_imx->msglen - lpi2c_imx->delivered; + + if (!remaining) { + complete(&lpi2c_imx->complete); + return; + } + + /* not finished, still waiting for rx data */ + lpi2c_imx_set_rx_watermark(lpi2c_imx); + + /* multiple receive commands */ + if (lpi2c_imx->block_data) { + lpi2c_imx->block_data = 0; + temp = remaining; + temp |= (RECV_DATA << 8); + writel(temp, lpi2c_imx->base + LPI2C_MTDR); + } else if (!(lpi2c_imx->delivered & 0xff)) { + temp = (remaining > CHUNK_DATA ? CHUNK_DATA : remaining) - 1; + temp |= (RECV_DATA << 8); + writel(temp, lpi2c_imx->base + LPI2C_MTDR); + } + + lpi2c_imx_intctrl(lpi2c_imx, MIER_RDIE); +} + +static void lpi2c_imx_write(struct lpi2c_imx_struct *lpi2c_imx, + struct i2c_msg *msgs) +{ + lpi2c_imx->tx_buf = msgs->buf; + lpi2c_imx_set_tx_watermark(lpi2c_imx); + lpi2c_imx_write_txfifo(lpi2c_imx); +} + +static void lpi2c_imx_read(struct lpi2c_imx_struct *lpi2c_imx, + struct i2c_msg *msgs) +{ + unsigned int temp; + + lpi2c_imx->rx_buf = msgs->buf; + lpi2c_imx->block_data = msgs->flags & I2C_M_RECV_LEN; + + lpi2c_imx_set_rx_watermark(lpi2c_imx); + temp = msgs->len > CHUNK_DATA ? CHUNK_DATA - 1 : msgs->len - 1; + temp |= (RECV_DATA << 8); + writel(temp, lpi2c_imx->base + LPI2C_MTDR); + + lpi2c_imx_intctrl(lpi2c_imx, MIER_RDIE | MIER_NDIE); +} + +static int lpi2c_imx_xfer(struct i2c_adapter *adapter, + struct i2c_msg *msgs, int num) +{ + struct lpi2c_imx_struct *lpi2c_imx = i2c_get_adapdata(adapter); + unsigned int temp; + int i, result; + + result = lpi2c_imx_master_enable(lpi2c_imx); + if (result) + return result; + + for (i = 0; i < num; i++) { + result = lpi2c_imx_start(lpi2c_imx, &msgs[i]); + if (result) + goto disable; + + /* quick smbus */ + if (num == 1 && msgs[0].len == 0) + goto stop; + + lpi2c_imx->delivered = 0; + lpi2c_imx->msglen = msgs[i].len; + init_completion(&lpi2c_imx->complete); + + if (msgs[i].flags & I2C_M_RD) + lpi2c_imx_read(lpi2c_imx, &msgs[i]); + else + lpi2c_imx_write(lpi2c_imx, &msgs[i]); + + result = lpi2c_imx_msg_complete(lpi2c_imx); + if (result) + goto stop; + + if (!(msgs[i].flags & I2C_M_RD)) { + result = lpi2c_imx_txfifo_empty(lpi2c_imx); + if (result) + goto stop; + } + } + +stop: + lpi2c_imx_stop(lpi2c_imx); + + temp = readl(lpi2c_imx->base + LPI2C_MSR); + if ((temp & MSR_NDF) && !result) + result = -EIO; + +disable: + lpi2c_imx_master_disable(lpi2c_imx); + + dev_dbg(&lpi2c_imx->adapter.dev, "<%s> exit with: %s: %d\n", __func__, + (result < 0) ? "error" : "success msg", + (result < 0) ? result : num); + + return (result < 0) ? result : num; +} + +static irqreturn_t lpi2c_imx_isr(int irq, void *dev_id) +{ + struct lpi2c_imx_struct *lpi2c_imx = dev_id; + unsigned int temp; + + lpi2c_imx_intctrl(lpi2c_imx, 0); + temp = readl(lpi2c_imx->base + LPI2C_MSR); + + if (temp & MSR_RDF) + lpi2c_imx_read_rxfifo(lpi2c_imx); + + if (temp & MSR_TDF) + lpi2c_imx_write_txfifo(lpi2c_imx); + + if (temp & MSR_NDF) + complete(&lpi2c_imx->complete); + + return IRQ_HANDLED; +} + +static u32 lpi2c_imx_func(struct i2c_adapter *adapter) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | + I2C_FUNC_SMBUS_READ_BLOCK_DATA; +} + +static struct i2c_algorithm lpi2c_imx_algo = { + .master_xfer = lpi2c_imx_xfer, + .functionality = lpi2c_imx_func, +}; + +static const struct of_device_id lpi2c_imx_of_match[] = { + { .compatible = "fsl,imx7ulp-lpi2c" }, + { .compatible = "fsl,imx8dv-lpi2c" }, + { }, +}; +MODULE_DEVICE_TABLE(of, lpi2c_imx_of_match); + +static int lpi2c_imx_probe(struct platform_device *pdev) +{ + struct lpi2c_imx_struct *lpi2c_imx; + struct resource *res; + unsigned int temp; + int irq, ret; + + lpi2c_imx = devm_kzalloc(&pdev->dev, sizeof(*lpi2c_imx), GFP_KERNEL); + if (!lpi2c_imx) + return -ENOMEM; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + lpi2c_imx->base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(lpi2c_imx->base)) + return PTR_ERR(lpi2c_imx->base); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "can't get irq number\n"); + return irq; + } + + lpi2c_imx->adapter.owner = THIS_MODULE; + lpi2c_imx->adapter.algo = &lpi2c_imx_algo; + lpi2c_imx->adapter.dev.parent = &pdev->dev; + lpi2c_imx->adapter.dev.of_node = pdev->dev.of_node; + strlcpy(lpi2c_imx->adapter.name, pdev->name, + sizeof(lpi2c_imx->adapter.name)); + + lpi2c_imx->clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(lpi2c_imx->clk)) { + dev_err(&pdev->dev, "can't get I2C peripheral clock\n"); + return PTR_ERR(lpi2c_imx->clk); + } + + ret = of_property_read_u32(pdev->dev.of_node, + "clock-frequency", &lpi2c_imx->bitrate); + if (ret) + lpi2c_imx->bitrate = LPI2C_DEFAULT_RATE; + + ret = devm_request_irq(&pdev->dev, irq, lpi2c_imx_isr, 0, + pdev->name, lpi2c_imx); + if (ret) { + dev_err(&pdev->dev, "can't claim irq %d\n", irq); + return ret; + } + + i2c_set_adapdata(&lpi2c_imx->adapter, lpi2c_imx); + platform_set_drvdata(pdev, lpi2c_imx); + + ret = clk_prepare_enable(lpi2c_imx->clk); + if (ret) { + dev_err(&pdev->dev, "clk enable failed %d\n", ret); + return ret; + } + + temp = readl(lpi2c_imx->base + LPI2C_PARAM); + lpi2c_imx->txfifosize = 1 << (temp & 0x0f); + lpi2c_imx->rxfifosize = 1 << ((temp >> 8) & 0x0f); + + clk_disable(lpi2c_imx->clk); + + ret = i2c_add_adapter(&lpi2c_imx->adapter); + if (ret) + goto clk_unprepare; + + dev_info(&lpi2c_imx->adapter.dev, "LPI2C adapter registered\n"); + + return 0; + +clk_unprepare: + clk_unprepare(lpi2c_imx->clk); + + return ret; +} + +static int lpi2c_imx_remove(struct platform_device *pdev) +{ + struct lpi2c_imx_struct *lpi2c_imx = platform_get_drvdata(pdev); + + i2c_del_adapter(&lpi2c_imx->adapter); + + clk_unprepare(lpi2c_imx->clk); + + return 0; +} + +static struct platform_driver lpi2c_imx_driver = { + .probe = lpi2c_imx_probe, + .remove = lpi2c_imx_remove, + .driver = { + .name = DRIVER_NAME, + .of_match_table = lpi2c_imx_of_match, + }, +}; + +module_platform_driver(lpi2c_imx_driver); + +MODULE_AUTHOR("Gao Pan "); +MODULE_DESCRIPTION("I2C adapter driver for LPI2C bus"); +MODULE_LICENSE("GPL"); diff --git a/drivers/i2c/busses/i2c-mlxcpld.c b/drivers/i2c/busses/i2c-mlxcpld.c new file mode 100644 index 000000000000..d271e6a0954c --- /dev/null +++ b/drivers/i2c/busses/i2c-mlxcpld.c @@ -0,0 +1,504 @@ +/* + * Copyright (c) 2016 Mellanox Technologies. All rights reserved. + * Copyright (c) 2016 Michael Shych + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the names of the copyright holders nor the names of its + * contributors may be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + */ + +#include +#include +#include +#include +#include +#include +#include + +/* General defines */ +#define MLXPLAT_CPLD_LPC_I2C_BASE_ADDR 0x2000 +#define MLXCPLD_I2C_DEVICE_NAME "i2c_mlxcpld" +#define MLXCPLD_I2C_VALID_FLAG (I2C_M_RECV_LEN | I2C_M_RD) +#define MLXCPLD_I2C_BUS_NUM 1 +#define MLXCPLD_I2C_DATA_REG_SZ 36 +#define MLXCPLD_I2C_MAX_ADDR_LEN 4 +#define MLXCPLD_I2C_RETR_NUM 2 +#define MLXCPLD_I2C_XFER_TO 500000 /* usec */ +#define MLXCPLD_I2C_POLL_TIME 2000 /* usec */ + +/* LPC I2C registers */ +#define MLXCPLD_LPCI2C_LPF_REG 0x0 +#define MLXCPLD_LPCI2C_CTRL_REG 0x1 +#define MLXCPLD_LPCI2C_HALF_CYC_REG 0x4 +#define MLXCPLD_LPCI2C_I2C_HOLD_REG 0x5 +#define MLXCPLD_LPCI2C_CMD_REG 0x6 +#define MLXCPLD_LPCI2C_NUM_DAT_REG 0x7 +#define MLXCPLD_LPCI2C_NUM_ADDR_REG 0x8 +#define MLXCPLD_LPCI2C_STATUS_REG 0x9 +#define MLXCPLD_LPCI2C_DATA_REG 0xa + +/* LPC I2C masks and parametres */ +#define MLXCPLD_LPCI2C_RST_SEL_MASK 0x1 +#define MLXCPLD_LPCI2C_TRANS_END 0x1 +#define MLXCPLD_LPCI2C_STATUS_NACK 0x10 +#define MLXCPLD_LPCI2C_NO_IND 0 +#define MLXCPLD_LPCI2C_ACK_IND 1 +#define MLXCPLD_LPCI2C_NACK_IND 2 + +struct mlxcpld_i2c_curr_xfer { + u8 cmd; + u8 addr_width; + u8 data_len; + u8 msg_num; + struct i2c_msg *msg; +}; + +struct mlxcpld_i2c_priv { + struct i2c_adapter adap; + u32 base_addr; + struct mutex lock; + struct mlxcpld_i2c_curr_xfer xfer; + struct device *dev; +}; + +static void mlxcpld_i2c_lpc_write_buf(u8 *data, u8 len, u32 addr) +{ + int i; + + for (i = 0; i < len - len % 4; i += 4) + outl(*(u32 *)(data + i), addr + i); + for (; i < len; ++i) + outb(*(data + i), addr + i); +} + +static void mlxcpld_i2c_lpc_read_buf(u8 *data, u8 len, u32 addr) +{ + int i; + + for (i = 0; i < len - len % 4; i += 4) + *(u32 *)(data + i) = inl(addr + i); + for (; i < len; ++i) + *(data + i) = inb(addr + i); +} + +static void mlxcpld_i2c_read_comm(struct mlxcpld_i2c_priv *priv, u8 offs, + u8 *data, u8 datalen) +{ + u32 addr = priv->base_addr + offs; + + switch (datalen) { + case 1: + *(data) = inb(addr); + break; + case 2: + *((u16 *)data) = inw(addr); + break; + case 3: + *((u16 *)data) = inw(addr); + *(data + 2) = inb(addr + 2); + break; + case 4: + *((u32 *)data) = inl(addr); + break; + default: + mlxcpld_i2c_lpc_read_buf(data, datalen, addr); + break; + } +} + +static void mlxcpld_i2c_write_comm(struct mlxcpld_i2c_priv *priv, u8 offs, + u8 *data, u8 datalen) +{ + u32 addr = priv->base_addr + offs; + + switch (datalen) { + case 1: + outb(*(data), addr); + break; + case 2: + outw(*((u16 *)data), addr); + break; + case 3: + outw(*((u16 *)data), addr); + outb(*(data + 2), addr + 2); + break; + case 4: + outl(*((u32 *)data), addr); + break; + default: + mlxcpld_i2c_lpc_write_buf(data, datalen, addr); + break; + } +} + +/* + * Check validity of received i2c messages parameters. + * Returns 0 if OK, other - in case of invalid parameters. + */ +static int mlxcpld_i2c_check_msg_params(struct mlxcpld_i2c_priv *priv, + struct i2c_msg *msgs, int num) +{ + int i; + + if (!num) { + dev_err(priv->dev, "Incorrect 0 num of messages\n"); + return -EINVAL; + } + + if (unlikely(msgs[0].addr > 0x7f)) { + dev_err(priv->dev, "Invalid address 0x%03x\n", + msgs[0].addr); + return -EINVAL; + } + + for (i = 0; i < num; ++i) { + if (unlikely(!msgs[i].buf)) { + dev_err(priv->dev, "Invalid buf in msg[%d]\n", + i); + return -EINVAL; + } + if (unlikely(msgs[0].addr != msgs[i].addr)) { + dev_err(priv->dev, "Invalid addr in msg[%d]\n", + i); + return -EINVAL; + } + } + + return 0; +} + +/* + * Check if transfer is completed and status of operation. + * Returns 0 - transfer completed (both ACK or NACK), + * negative - transfer isn't finished. + */ +static int mlxcpld_i2c_check_status(struct mlxcpld_i2c_priv *priv, int *status) +{ + u8 val; + + mlxcpld_i2c_read_comm(priv, MLXCPLD_LPCI2C_STATUS_REG, &val, 1); + + if (val & MLXCPLD_LPCI2C_TRANS_END) { + if (val & MLXCPLD_LPCI2C_STATUS_NACK) + /* + * The slave is unable to accept the data. No such + * slave, command not understood, or unable to accept + * any more data. + */ + *status = MLXCPLD_LPCI2C_NACK_IND; + else + *status = MLXCPLD_LPCI2C_ACK_IND; + return 0; + } + *status = MLXCPLD_LPCI2C_NO_IND; + + return -EIO; +} + +static void mlxcpld_i2c_set_transf_data(struct mlxcpld_i2c_priv *priv, + struct i2c_msg *msgs, int num, + u8 comm_len) +{ + priv->xfer.msg = msgs; + priv->xfer.msg_num = num; + + /* + * All upper layers currently are never use transfer with more than + * 2 messages. Actually, it's also not so relevant in Mellanox systems + * because of HW limitation. Max size of transfer is not more than 32 + * bytes in the current x86 LPCI2C bridge. + */ + priv->xfer.cmd = msgs[num - 1].flags & I2C_M_RD; + + if (priv->xfer.cmd == I2C_M_RD && comm_len != msgs[0].len) { + priv->xfer.addr_width = msgs[0].len; + priv->xfer.data_len = comm_len - priv->xfer.addr_width; + } else { + priv->xfer.addr_width = 0; + priv->xfer.data_len = comm_len; + } +} + +/* Reset CPLD LPCI2C block */ +static void mlxcpld_i2c_reset(struct mlxcpld_i2c_priv *priv) +{ + u8 val; + + mutex_lock(&priv->lock); + + mlxcpld_i2c_read_comm(priv, MLXCPLD_LPCI2C_CTRL_REG, &val, 1); + val &= ~MLXCPLD_LPCI2C_RST_SEL_MASK; + mlxcpld_i2c_write_comm(priv, MLXCPLD_LPCI2C_CTRL_REG, &val, 1); + + mutex_unlock(&priv->lock); +} + +/* Make sure the CPLD is ready to start transmitting. */ +static int mlxcpld_i2c_check_busy(struct mlxcpld_i2c_priv *priv) +{ + u8 val; + + mlxcpld_i2c_read_comm(priv, MLXCPLD_LPCI2C_STATUS_REG, &val, 1); + + if (val & MLXCPLD_LPCI2C_TRANS_END) + return 0; + + return -EIO; +} + +static int mlxcpld_i2c_wait_for_free(struct mlxcpld_i2c_priv *priv) +{ + int timeout = 0; + + do { + if (!mlxcpld_i2c_check_busy(priv)) + break; + usleep_range(MLXCPLD_I2C_POLL_TIME / 2, MLXCPLD_I2C_POLL_TIME); + timeout += MLXCPLD_I2C_POLL_TIME; + } while (timeout <= MLXCPLD_I2C_XFER_TO); + + if (timeout > MLXCPLD_I2C_XFER_TO) + return -ETIMEDOUT; + + return 0; +} + +/* + * Wait for master transfer to complete. + * It puts current process to sleep until we get interrupt or timeout expires. + * Returns the number of transferred or read bytes or error (<0). + */ +static int mlxcpld_i2c_wait_for_tc(struct mlxcpld_i2c_priv *priv) +{ + int status, i, timeout = 0; + u8 datalen; + + do { + usleep_range(MLXCPLD_I2C_POLL_TIME / 2, MLXCPLD_I2C_POLL_TIME); + if (!mlxcpld_i2c_check_status(priv, &status)) + break; + timeout += MLXCPLD_I2C_POLL_TIME; + } while (status == 0 && timeout < MLXCPLD_I2C_XFER_TO); + + switch (status) { + case MLXCPLD_LPCI2C_NO_IND: + return -ETIMEDOUT; + + case MLXCPLD_LPCI2C_ACK_IND: + if (priv->xfer.cmd != I2C_M_RD) + return (priv->xfer.addr_width + priv->xfer.data_len); + + if (priv->xfer.msg_num == 1) + i = 0; + else + i = 1; + + if (!priv->xfer.msg[i].buf) + return -EINVAL; + + /* + * Actual read data len will be always the same as + * requested len. 0xff (line pull-up) will be returned + * if slave has no data to return. Thus don't read + * MLXCPLD_LPCI2C_NUM_DAT_REG reg from CPLD. + */ + datalen = priv->xfer.data_len; + + mlxcpld_i2c_read_comm(priv, MLXCPLD_LPCI2C_DATA_REG, + priv->xfer.msg[i].buf, datalen); + + return datalen; + + case MLXCPLD_LPCI2C_NACK_IND: + return -ENXIO; + + default: + return -EINVAL; + } +} + +static void mlxcpld_i2c_xfer_msg(struct mlxcpld_i2c_priv *priv) +{ + int i, len = 0; + u8 cmd; + + mlxcpld_i2c_write_comm(priv, MLXCPLD_LPCI2C_NUM_DAT_REG, + &priv->xfer.data_len, 1); + mlxcpld_i2c_write_comm(priv, MLXCPLD_LPCI2C_NUM_ADDR_REG, + &priv->xfer.addr_width, 1); + + for (i = 0; i < priv->xfer.msg_num; i++) { + if ((priv->xfer.msg[i].flags & I2C_M_RD) != I2C_M_RD) { + /* Don't write to CPLD buffer in read transaction */ + mlxcpld_i2c_write_comm(priv, MLXCPLD_LPCI2C_DATA_REG + + len, priv->xfer.msg[i].buf, + priv->xfer.msg[i].len); + len += priv->xfer.msg[i].len; + } + } + + /* + * Set target slave address with command for master transfer. + * It should be latest executed function before CPLD transaction. + */ + cmd = (priv->xfer.msg[0].addr << 1) | priv->xfer.cmd; + mlxcpld_i2c_write_comm(priv, MLXCPLD_LPCI2C_CMD_REG, &cmd, 1); +} + +/* + * Generic lpc-i2c transfer. + * Returns the number of processed messages or error (<0). + */ +static int mlxcpld_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, + int num) +{ + struct mlxcpld_i2c_priv *priv = i2c_get_adapdata(adap); + u8 comm_len = 0; + int i, err; + + err = mlxcpld_i2c_check_msg_params(priv, msgs, num); + if (err) { + dev_err(priv->dev, "Incorrect message\n"); + return err; + } + + for (i = 0; i < num; ++i) + comm_len += msgs[i].len; + + /* Check bus state */ + if (mlxcpld_i2c_wait_for_free(priv)) { + dev_err(priv->dev, "LPCI2C bridge is busy\n"); + + /* + * Usually it means something serious has happened. + * We can not have unfinished previous transfer + * so it doesn't make any sense to try to stop it. + * Probably we were not able to recover from the + * previous error. + * The only reasonable thing - is soft reset. + */ + mlxcpld_i2c_reset(priv); + if (mlxcpld_i2c_check_busy(priv)) { + dev_err(priv->dev, "LPCI2C bridge is busy after reset\n"); + return -EIO; + } + } + + mlxcpld_i2c_set_transf_data(priv, msgs, num, comm_len); + + mutex_lock(&priv->lock); + + /* Do real transfer. Can't fail */ + mlxcpld_i2c_xfer_msg(priv); + + /* Wait for transaction complete */ + err = mlxcpld_i2c_wait_for_tc(priv); + + mutex_unlock(&priv->lock); + + return err < 0 ? err : num; +} + +static u32 mlxcpld_i2c_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL | I2C_FUNC_SMBUS_BLOCK_DATA; +} + +static const struct i2c_algorithm mlxcpld_i2c_algo = { + .master_xfer = mlxcpld_i2c_xfer, + .functionality = mlxcpld_i2c_func +}; + +static struct i2c_adapter_quirks mlxcpld_i2c_quirks = { + .flags = I2C_AQ_COMB_WRITE_THEN_READ, + .max_read_len = MLXCPLD_I2C_DATA_REG_SZ - MLXCPLD_I2C_MAX_ADDR_LEN, + .max_write_len = MLXCPLD_I2C_DATA_REG_SZ, + .max_comb_1st_msg_len = 4, +}; + +static struct i2c_adapter mlxcpld_i2c_adapter = { + .owner = THIS_MODULE, + .name = "i2c-mlxcpld", + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, + .algo = &mlxcpld_i2c_algo, + .quirks = &mlxcpld_i2c_quirks, + .retries = MLXCPLD_I2C_RETR_NUM, + .nr = MLXCPLD_I2C_BUS_NUM, +}; + +static int mlxcpld_i2c_probe(struct platform_device *pdev) +{ + struct mlxcpld_i2c_priv *priv; + int err; + + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + mutex_init(&priv->lock); + platform_set_drvdata(pdev, priv); + + priv->dev = &pdev->dev; + + /* Register with i2c layer */ + mlxcpld_i2c_adapter.timeout = usecs_to_jiffies(MLXCPLD_I2C_XFER_TO); + priv->adap = mlxcpld_i2c_adapter; + priv->adap.dev.parent = &pdev->dev; + priv->base_addr = MLXPLAT_CPLD_LPC_I2C_BASE_ADDR; + i2c_set_adapdata(&priv->adap, priv); + + err = i2c_add_numbered_adapter(&priv->adap); + if (err) + mutex_destroy(&priv->lock); + + return err; +} + +static int mlxcpld_i2c_remove(struct platform_device *pdev) +{ + struct mlxcpld_i2c_priv *priv = platform_get_drvdata(pdev); + + i2c_del_adapter(&priv->adap); + mutex_destroy(&priv->lock); + + return 0; +} + +static struct platform_driver mlxcpld_i2c_driver = { + .probe = mlxcpld_i2c_probe, + .remove = mlxcpld_i2c_remove, + .driver = { + .name = MLXCPLD_I2C_DEVICE_NAME, + }, +}; + +module_platform_driver(mlxcpld_i2c_driver); + +MODULE_AUTHOR("Michael Shych "); +MODULE_DESCRIPTION("Mellanox I2C-CPLD controller driver"); +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_ALIAS("platform:i2c-mlxcpld"); diff --git a/drivers/i2c/busses/i2c-octeon-core.c b/drivers/i2c/busses/i2c-octeon-core.c index 5e63b17f935d..3d10f1a802be 100644 --- a/drivers/i2c/busses/i2c-octeon-core.c +++ b/drivers/i2c/busses/i2c-octeon-core.c @@ -36,24 +36,6 @@ static bool octeon_i2c_test_iflg(struct octeon_i2c *i2c) return (octeon_i2c_ctl_read(i2c) & TWSI_CTL_IFLG); } -static bool octeon_i2c_test_ready(struct octeon_i2c *i2c, bool *first) -{ - if (octeon_i2c_test_iflg(i2c)) - return true; - - if (*first) { - *first = false; - return false; - } - - /* - * IRQ has signaled an event but IFLG hasn't changed. - * Sleep and retry once. - */ - usleep_range(I2C_OCTEON_EVENT_WAIT, 2 * I2C_OCTEON_EVENT_WAIT); - return octeon_i2c_test_iflg(i2c); -} - /** * octeon_i2c_wait - wait for the IFLG to be set * @i2c: The struct octeon_i2c @@ -63,7 +45,6 @@ static bool octeon_i2c_test_ready(struct octeon_i2c *i2c, bool *first) static int octeon_i2c_wait(struct octeon_i2c *i2c) { long time_left; - bool first = true; /* * Some chip revisions don't assert the irq in the interrupt @@ -80,7 +61,7 @@ static int octeon_i2c_wait(struct octeon_i2c *i2c) } i2c->int_enable(i2c); - time_left = wait_event_timeout(i2c->queue, octeon_i2c_test_ready(i2c, &first), + time_left = wait_event_timeout(i2c->queue, octeon_i2c_test_iflg(i2c), i2c->adap.timeout); i2c->int_disable(i2c); @@ -102,25 +83,6 @@ static bool octeon_i2c_hlc_test_valid(struct octeon_i2c *i2c) return (__raw_readq(i2c->twsi_base + SW_TWSI(i2c)) & SW_TWSI_V) == 0; } -static bool octeon_i2c_hlc_test_ready(struct octeon_i2c *i2c, bool *first) -{ - /* check if valid bit is cleared */ - if (octeon_i2c_hlc_test_valid(i2c)) - return true; - - if (*first) { - *first = false; - return false; - } - - /* - * IRQ has signaled an event but valid bit isn't cleared. - * Sleep and retry once. - */ - usleep_range(I2C_OCTEON_EVENT_WAIT, 2 * I2C_OCTEON_EVENT_WAIT); - return octeon_i2c_hlc_test_valid(i2c); -} - static void octeon_i2c_hlc_int_clear(struct octeon_i2c *i2c) { /* clear ST/TS events, listen for neither */ @@ -176,7 +138,6 @@ static void octeon_i2c_hlc_disable(struct octeon_i2c *i2c) */ static int octeon_i2c_hlc_wait(struct octeon_i2c *i2c) { - bool first = true; int time_left; /* @@ -195,7 +156,7 @@ static int octeon_i2c_hlc_wait(struct octeon_i2c *i2c) i2c->hlc_int_enable(i2c); time_left = wait_event_timeout(i2c->queue, - octeon_i2c_hlc_test_ready(i2c, &first), + octeon_i2c_hlc_test_valid(i2c), i2c->adap.timeout); i2c->hlc_int_disable(i2c); if (!time_left) @@ -789,6 +750,9 @@ static void octeon_i2c_prepare_recovery(struct i2c_adapter *adap) struct octeon_i2c *i2c = i2c_get_adapdata(adap); octeon_i2c_hlc_disable(i2c); + octeon_i2c_reg_write(i2c, SW_TWSI_EOP_TWSI_RST, 0); + /* wait for software reset to settle */ + udelay(5); /* * Bring control register to a good state regardless diff --git a/drivers/i2c/busses/i2c-pxa-pci.c b/drivers/i2c/busses/i2c-pxa-pci.c index 417464e9ea2a..004deb96afe3 100644 --- a/drivers/i2c/busses/i2c-pxa-pci.c +++ b/drivers/i2c/busses/i2c-pxa-pci.c @@ -1,9 +1,13 @@ /* + * CE4100 PCI-I2C glue code for PXA's driver + * Author: Sebastian Andrzej Siewior + * License: GPL v2 + * * The CE4100's I2C device is more or less the same one as found on PXA. * It does not support slave mode, the register slightly moved. This PCI * device provides three bars, every contains a single I2C controller. */ -#include +#include #include #include #include @@ -134,35 +138,17 @@ err_mem: return ret; } -static void ce4100_i2c_remove(struct pci_dev *dev) -{ - struct ce4100_devices *sds; - unsigned int i; - - sds = pci_get_drvdata(dev); - - for (i = 0; i < ARRAY_SIZE(sds->pdev); i++) - platform_device_unregister(sds->pdev[i]); - - pci_disable_device(dev); - kfree(sds); -} - static const struct pci_device_id ce4100_i2c_devices[] = { { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x2e68)}, { }, }; -MODULE_DEVICE_TABLE(pci, ce4100_i2c_devices); static struct pci_driver ce4100_i2c_driver = { + .driver = { + .suppress_bind_attrs = true, + }, .name = "ce4100_i2c", .id_table = ce4100_i2c_devices, .probe = ce4100_i2c_probe, - .remove = ce4100_i2c_remove, }; - -module_pci_driver(ce4100_i2c_driver); - -MODULE_DESCRIPTION("CE4100 PCI-I2C glue code for PXA's driver"); -MODULE_LICENSE("GPL v2"); -MODULE_AUTHOR("Sebastian Andrzej Siewior "); +builtin_pci_driver(ce4100_i2c_driver); diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c index e28b825b0433..6cf333ecc8b8 100644 --- a/drivers/i2c/busses/i2c-pxa.c +++ b/drivers/i2c/busses/i2c-pxa.c @@ -48,6 +48,8 @@ struct pxa_reg_layout { u32 isar; u32 ilcr; u32 iwcr; + u32 fm; + u32 hs; }; enum pxa_i2c_types { @@ -55,8 +57,12 @@ enum pxa_i2c_types { REGS_PXA3XX, REGS_CE4100, REGS_PXA910, + REGS_A3700, }; +#define ICR_BUSMODE_FM (1 << 16) /* shifted fast mode for armada-3700 */ +#define ICR_BUSMODE_HS (1 << 17) /* shifted high speed mode for armada-3700 */ + /* * I2C registers definitions */ @@ -91,6 +97,15 @@ static struct pxa_reg_layout pxa_reg_layout[] = { .ilcr = 0x28, .iwcr = 0x30, }, + [REGS_A3700] = { + .ibmr = 0x00, + .idbr = 0x04, + .icr = 0x08, + .isr = 0x0c, + .isar = 0x10, + .fm = ICR_BUSMODE_FM, + .hs = ICR_BUSMODE_HS, + }, }; static const struct platform_device_id i2c_pxa_id_table[] = { @@ -98,6 +113,7 @@ static const struct platform_device_id i2c_pxa_id_table[] = { { "pxa3xx-pwri2c", REGS_PXA3XX }, { "ce4100-i2c", REGS_CE4100 }, { "pxa910-i2c", REGS_PXA910 }, + { "armada-3700-i2c", REGS_A3700 }, { }, }; MODULE_DEVICE_TABLE(platform, i2c_pxa_id_table); @@ -193,6 +209,8 @@ struct pxa_i2c { unsigned char master_code; unsigned long rate; bool highmode_enter; + u32 fm_mask; + u32 hs_mask; }; #define _IBMR(i2c) ((i2c)->reg_ibmr) @@ -503,8 +521,8 @@ static void i2c_pxa_reset(struct pxa_i2c *i2c) writel(i2c->slave_addr, _ISAR(i2c)); /* set control register values */ - writel(I2C_ICR_INIT | (i2c->fast_mode ? ICR_FM : 0), _ICR(i2c)); - writel(readl(_ICR(i2c)) | (i2c->high_mode ? ICR_HS : 0), _ICR(i2c)); + writel(I2C_ICR_INIT | (i2c->fast_mode ? i2c->fm_mask : 0), _ICR(i2c)); + writel(readl(_ICR(i2c)) | (i2c->high_mode ? i2c->hs_mask : 0), _ICR(i2c)); #ifdef CONFIG_I2C_PXA_SLAVE dev_info(&i2c->adap.dev, "Enabling slave mode\n"); @@ -1137,6 +1155,7 @@ static const struct of_device_id i2c_pxa_dt_ids[] = { { .compatible = "mrvl,pxa-i2c", .data = (void *)REGS_PXA2XX }, { .compatible = "mrvl,pwri2c", .data = (void *)REGS_PXA3XX }, { .compatible = "mrvl,mmp-twsi", .data = (void *)REGS_PXA910 }, + { .compatible = "marvell,armada-3700-i2c", .data = (void *)REGS_A3700 }, {} }; MODULE_DEVICE_TABLE(of, i2c_pxa_dt_ids); @@ -1234,6 +1253,9 @@ static int i2c_pxa_probe(struct platform_device *dev) i2c->reg_idbr = i2c->reg_base + pxa_reg_layout[i2c_type].idbr; i2c->reg_icr = i2c->reg_base + pxa_reg_layout[i2c_type].icr; i2c->reg_isr = i2c->reg_base + pxa_reg_layout[i2c_type].isr; + i2c->fm_mask = pxa_reg_layout[i2c_type].fm ? : ICR_FM; + i2c->hs_mask = pxa_reg_layout[i2c_type].hs ? : ICR_HS; + if (i2c_type != REGS_CE4100) i2c->reg_isar = i2c->reg_base + pxa_reg_layout[i2c_type].isar; diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c index a8497cfdae6f..1902d8ac9753 100644 --- a/drivers/i2c/busses/i2c-qup.c +++ b/drivers/i2c/busses/i2c-qup.c @@ -14,6 +14,7 @@ * */ +#include #include #include #include @@ -132,6 +133,10 @@ /* Max timeout in ms for 32k bytes */ #define TOUT_MAX 300 +/* Default values. Use these if FW query fails */ +#define DEFAULT_CLK_FREQ 100000 +#define DEFAULT_SRC_CLK 20000000 + struct qup_i2c_block { int count; int pos; @@ -525,6 +530,33 @@ static int qup_i2c_get_data_len(struct qup_i2c_dev *qup) return data_len; } +static bool qup_i2c_check_msg_len(struct i2c_msg *msg) +{ + return ((msg->flags & I2C_M_RD) && (msg->flags & I2C_M_RECV_LEN)); +} + +static int qup_i2c_set_tags_smb(u16 addr, u8 *tags, struct qup_i2c_dev *qup, + struct i2c_msg *msg) +{ + int len = 0; + + if (msg->len > 1) { + tags[len++] = QUP_TAG_V2_DATARD_STOP; + tags[len++] = qup_i2c_get_data_len(qup) - 1; + } else { + tags[len++] = QUP_TAG_V2_START; + tags[len++] = addr & 0xff; + + if (msg->flags & I2C_M_TEN) + tags[len++] = addr >> 8; + + tags[len++] = QUP_TAG_V2_DATARD; + /* Read 1 byte indicating the length of the SMBus message */ + tags[len++] = 1; + } + return len; +} + static int qup_i2c_set_tags(u8 *tags, struct qup_i2c_dev *qup, struct i2c_msg *msg, int is_dma) { @@ -534,6 +566,10 @@ static int qup_i2c_set_tags(u8 *tags, struct qup_i2c_dev *qup, int last = (qup->blk.pos == (qup->blk.count - 1)) && (qup->is_last); + /* Handle tags for SMBus block read */ + if (qup_i2c_check_msg_len(msg)) + return qup_i2c_set_tags_smb(addr, tags, qup, msg); + if (qup->blk.pos == 0) { tags[len++] = QUP_TAG_V2_START; tags[len++] = addr & 0xff; @@ -1056,9 +1092,17 @@ static int qup_i2c_read_fifo_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg) { u32 val; - int idx, pos = 0, ret = 0, total; + int idx, pos = 0, ret = 0, total, msg_offset = 0; + /* + * If the message length is already read in + * the first byte of the buffer, account for + * that by setting the offset + */ + if (qup_i2c_check_msg_len(msg) && (msg->len > 1)) + msg_offset = 1; total = qup_i2c_get_data_len(qup); + total -= msg_offset; /* 2 extra bytes for read tags */ while (pos < (total + 2)) { @@ -1078,8 +1122,8 @@ static int qup_i2c_read_fifo_v2(struct qup_i2c_dev *qup, if (pos >= (total + 2)) goto out; - - msg->buf[qup->pos++] = val & 0xff; + msg->buf[qup->pos + msg_offset] = val & 0xff; + qup->pos++; } } @@ -1119,6 +1163,20 @@ static int qup_i2c_read_one_v2(struct qup_i2c_dev *qup, struct i2c_msg *msg) goto err; qup->blk.pos++; + + /* Handle SMBus block read length */ + if (qup_i2c_check_msg_len(msg) && (msg->len == 1)) { + if (msg->buf[0] > I2C_SMBUS_BLOCK_MAX) { + ret = -EPROTO; + goto err; + } + msg->len += msg->buf[0]; + qup->pos = 0; + qup_i2c_set_blk_data(qup, msg); + /* set tag length for block read */ + qup->blk.tx_tag_len = 2; + qup_i2c_set_read_mode_v2(qup, msg->buf[0]); + } } while (qup->blk.pos < qup->blk.count); err: @@ -1204,6 +1262,11 @@ static int qup_i2c_xfer(struct i2c_adapter *adap, goto out; } + if (qup_i2c_check_msg_len(&msgs[idx])) { + ret = -EINVAL; + goto out; + } + if (msgs[idx].flags & I2C_M_RD) ret = qup_i2c_read_one(qup, &msgs[idx]); else @@ -1358,14 +1421,13 @@ static void qup_i2c_disable_clocks(struct qup_i2c_dev *qup) static int qup_i2c_probe(struct platform_device *pdev) { static const int blk_sizes[] = {4, 16, 32}; - struct device_node *node = pdev->dev.of_node; struct qup_i2c_dev *qup; unsigned long one_bit_t; struct resource *res; u32 io_mode, hw_ver, size; int ret, fs_div, hs_div; - int src_clk_freq; - u32 clk_freq = 100000; + u32 src_clk_freq = DEFAULT_SRC_CLK; + u32 clk_freq = DEFAULT_CLK_FREQ; int blocks; qup = devm_kzalloc(&pdev->dev, sizeof(*qup), GFP_KERNEL); @@ -1376,7 +1438,11 @@ static int qup_i2c_probe(struct platform_device *pdev) init_completion(&qup->xfer); platform_set_drvdata(pdev, qup); - of_property_read_u32(node, "clock-frequency", &clk_freq); + ret = device_property_read_u32(qup->dev, "clock-frequency", &clk_freq); + if (ret) { + dev_notice(qup->dev, "using default clock-frequency %d", + DEFAULT_CLK_FREQ); + } if (of_device_is_compatible(pdev->dev.of_node, "qcom,i2c-qup-v1.1.1")) { qup->adap.algo = &qup_i2c_algo; @@ -1452,20 +1518,30 @@ nodma: return qup->irq; } - qup->clk = devm_clk_get(qup->dev, "core"); - if (IS_ERR(qup->clk)) { - dev_err(qup->dev, "Could not get core clock\n"); - return PTR_ERR(qup->clk); - } + if (has_acpi_companion(qup->dev)) { + ret = device_property_read_u32(qup->dev, + "src-clock-hz", &src_clk_freq); + if (ret) { + dev_notice(qup->dev, "using default src-clock-hz %d", + DEFAULT_SRC_CLK); + } + ACPI_COMPANION_SET(&qup->adap.dev, ACPI_COMPANION(qup->dev)); + } else { + qup->clk = devm_clk_get(qup->dev, "core"); + if (IS_ERR(qup->clk)) { + dev_err(qup->dev, "Could not get core clock\n"); + return PTR_ERR(qup->clk); + } - qup->pclk = devm_clk_get(qup->dev, "iface"); - if (IS_ERR(qup->pclk)) { - dev_err(qup->dev, "Could not get iface clock\n"); - return PTR_ERR(qup->pclk); + qup->pclk = devm_clk_get(qup->dev, "iface"); + if (IS_ERR(qup->pclk)) { + dev_err(qup->dev, "Could not get iface clock\n"); + return PTR_ERR(qup->pclk); + } + qup_i2c_enable_clocks(qup); + src_clk_freq = clk_get_rate(qup->clk); } - qup_i2c_enable_clocks(qup); - /* * Bootloaders might leave a pending interrupt on certain QUP's, * so we reset the core before registering for interrupts. @@ -1512,7 +1588,6 @@ nodma: size = QUP_INPUT_FIFO_SIZE(io_mode); qup->in_fifo_sz = qup->in_blk_sz * (2 << size); - src_clk_freq = clk_get_rate(qup->clk); fs_div = ((src_clk_freq / clk_freq) / 2) - 3; hs_div = 3; qup->clk_ctl = (hs_div << 8) | (fs_div & 0xff); @@ -1631,6 +1706,14 @@ static const struct of_device_id qup_i2c_dt_match[] = { }; MODULE_DEVICE_TABLE(of, qup_i2c_dt_match); +#if IS_ENABLED(CONFIG_ACPI) +static const struct acpi_device_id qup_i2c_acpi_match[] = { + { "QCOM8010"}, + { }, +}; +MODULE_DEVICE_TABLE(acpi, qup_i2c_acpi_match); +#endif + static struct platform_driver qup_i2c_driver = { .probe = qup_i2c_probe, .remove = qup_i2c_remove, @@ -1638,6 +1721,7 @@ static struct platform_driver qup_i2c_driver = { .name = "i2c_qup", .pm = &qup_i2c_qup_pm_ops, .of_match_table = qup_i2c_dt_match, + .acpi_match_table = ACPI_PTR(qup_i2c_acpi_match), }, }; diff --git a/drivers/i2c/busses/i2c-rcar.c b/drivers/i2c/busses/i2c-rcar.c index 726615e54f2a..26f2ff22e97e 100644 --- a/drivers/i2c/busses/i2c-rcar.c +++ b/drivers/i2c/busses/i2c-rcar.c @@ -793,7 +793,6 @@ static const struct i2c_algorithm rcar_i2c_algo = { }; static const struct of_device_id rcar_i2c_dt_ids[] = { - { .compatible = "renesas,i2c-rcar", .data = (void *)I2C_RCAR_GEN1 }, { .compatible = "renesas,i2c-r8a7778", .data = (void *)I2C_RCAR_GEN1 }, { .compatible = "renesas,i2c-r8a7779", .data = (void *)I2C_RCAR_GEN1 }, { .compatible = "renesas,i2c-r8a7790", .data = (void *)I2C_RCAR_GEN2 }, @@ -803,6 +802,10 @@ static const struct of_device_id rcar_i2c_dt_ids[] = { { .compatible = "renesas,i2c-r8a7794", .data = (void *)I2C_RCAR_GEN2 }, { .compatible = "renesas,i2c-r8a7795", .data = (void *)I2C_RCAR_GEN3 }, { .compatible = "renesas,i2c-r8a7796", .data = (void *)I2C_RCAR_GEN3 }, + { .compatible = "renesas,i2c-rcar", .data = (void *)I2C_RCAR_GEN1 }, /* Deprecated */ + { .compatible = "renesas,rcar-gen1-i2c", .data = (void *)I2C_RCAR_GEN1 }, + { .compatible = "renesas,rcar-gen2-i2c", .data = (void *)I2C_RCAR_GEN2 }, + { .compatible = "renesas,rcar-gen3-i2c", .data = (void *)I2C_RCAR_GEN3 }, {}, }; MODULE_DEVICE_TABLE(of, rcar_i2c_dt_ids); diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 192f36f00e4d..3d9ebe6e5716 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -827,7 +827,6 @@ static const struct sh_mobile_dt_config r8a7740_dt_config = { }; static const struct of_device_id sh_mobile_i2c_dt_ids[] = { - { .compatible = "renesas,rmobile-iic", .data = &default_dt_config }, { .compatible = "renesas,iic-r8a73a4", .data = &fast_clock_dt_config }, { .compatible = "renesas,iic-r8a7740", .data = &r8a7740_dt_config }, { .compatible = "renesas,iic-r8a7790", .data = &fast_clock_dt_config }, @@ -835,8 +834,11 @@ static const struct of_device_id sh_mobile_i2c_dt_ids[] = { { .compatible = "renesas,iic-r8a7792", .data = &fast_clock_dt_config }, { .compatible = "renesas,iic-r8a7793", .data = &fast_clock_dt_config }, { .compatible = "renesas,iic-r8a7794", .data = &fast_clock_dt_config }, + { .compatible = "renesas,rcar-gen2-iic", .data = &fast_clock_dt_config }, { .compatible = "renesas,iic-r8a7795", .data = &fast_clock_dt_config }, + { .compatible = "renesas,rcar-gen3-iic", .data = &fast_clock_dt_config }, { .compatible = "renesas,iic-sh73a0", .data = &fast_clock_dt_config }, + { .compatible = "renesas,rmobile-iic", .data = &default_dt_config }, {}, }; MODULE_DEVICE_TABLE(of, sh_mobile_i2c_dt_ids); diff --git a/drivers/i2c/busses/i2c-uniphier-f.c b/drivers/i2c/busses/i2c-uniphier-f.c index db9105e52c79..beee31892295 100644 --- a/drivers/i2c/busses/i2c-uniphier-f.c +++ b/drivers/i2c/busses/i2c-uniphier-f.c @@ -528,7 +528,7 @@ static int uniphier_fi2c_probe(struct platform_device *pdev) if (!clk_rate) { dev_err(dev, "input clock rate should not be zero\n"); ret = -EINVAL; - goto err; + goto disable_clk; } init_completion(&priv->comp); @@ -547,11 +547,11 @@ static int uniphier_fi2c_probe(struct platform_device *pdev) pdev->name, priv); if (ret) { dev_err(dev, "failed to request irq %d\n", irq); - goto err; + goto disable_clk; } ret = i2c_add_adapter(&priv->adap); -err: +disable_clk: if (ret) clk_disable_unprepare(priv->clk); diff --git a/drivers/i2c/busses/i2c-uniphier.c b/drivers/i2c/busses/i2c-uniphier.c index 56e92af46ddc..777c0fe93653 100644 --- a/drivers/i2c/busses/i2c-uniphier.c +++ b/drivers/i2c/busses/i2c-uniphier.c @@ -373,7 +373,7 @@ static int uniphier_i2c_probe(struct platform_device *pdev) if (!clk_rate) { dev_err(dev, "input clock rate should not be zero\n"); ret = -EINVAL; - goto err; + goto disable_clk; } init_completion(&priv->comp); @@ -392,11 +392,11 @@ static int uniphier_i2c_probe(struct platform_device *pdev) priv); if (ret) { dev_err(dev, "failed to request irq %d\n", irq); - goto err; + goto disable_clk; } ret = i2c_add_adapter(&priv->adap); -err: +disable_clk: if (ret) clk_disable_unprepare(priv->clk); diff --git a/drivers/i2c/busses/i2c-viperboard.c b/drivers/i2c/busses/i2c-viperboard.c index 543456a0a338..e4be86b3de9a 100644 --- a/drivers/i2c/busses/i2c-viperboard.c +++ b/drivers/i2c/busses/i2c-viperboard.c @@ -354,7 +354,7 @@ static const struct i2c_algorithm vprbrd_algorithm = { .functionality = vprbrd_i2c_func, }; -static struct i2c_adapter_quirks vprbrd_quirks = { +static const struct i2c_adapter_quirks vprbrd_quirks = { .max_read_len = 2048, .max_write_len = 2048, }; diff --git a/drivers/i2c/busses/i2c-xlp9xx.c b/drivers/i2c/busses/i2c-xlp9xx.c index e29ff37a43bd..84a8b2eccffb 100644 --- a/drivers/i2c/busses/i2c-xlp9xx.c +++ b/drivers/i2c/busses/i2c-xlp9xx.c @@ -393,6 +393,7 @@ static int xlp9xx_i2c_probe(struct platform_device *pdev) init_completion(&priv->msg_complete); priv->adapter.dev.parent = &pdev->dev; priv->adapter.algo = &xlp9xx_i2c_algo; + ACPI_COMPANION_SET(&priv->adapter.dev, ACPI_COMPANION(&pdev->dev)); priv->adapter.dev.of_node = pdev->dev.of_node; priv->dev = &pdev->dev; diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index b432b64e307a..3a1bc9c4efc7 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -65,6 +65,9 @@ #define I2C_ADDR_OFFSET_TEN_BIT 0xa000 #define I2C_ADDR_OFFSET_SLAVE 0x1000 +#define I2C_ADDR_7BITS_MAX 0x77 +#define I2C_ADDR_7BITS_COUNT (I2C_ADDR_7BITS_MAX + 1) + /* core_lock protects i2c_adapter_idr, and guarantees that device detection, deletion of detected devices, and attach_adapter calls are serialized */ @@ -676,9 +679,12 @@ static inline int i2c_acpi_install_space_handler(struct i2c_adapter *adapter) /* ------------------------------------------------------------------------- */ -static const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id, +const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id, const struct i2c_client *client) { + if (!(id && client)) + return NULL; + while (id->name[0]) { if (strcmp(client->name, id->name) == 0) return id; @@ -686,17 +692,16 @@ static const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id, } return NULL; } +EXPORT_SYMBOL_GPL(i2c_match_id); static int i2c_device_match(struct device *dev, struct device_driver *drv) { struct i2c_client *client = i2c_verify_client(dev); struct i2c_driver *driver; - if (!client) - return 0; /* Attempt an OF style match */ - if (of_driver_match_device(dev, drv)) + if (i2c_of_match_device(drv->of_match_table, client)) return 1; /* Then ACPI style match */ @@ -704,9 +709,10 @@ static int i2c_device_match(struct device *dev, struct device_driver *drv) return 1; driver = to_i2c_driver(drv); - /* match on an id table if there is one */ - if (driver->id_table) - return i2c_match_id(driver->id_table, client) != NULL; + + /* Finally an I2C match */ + if (i2c_match_id(driver->id_table, client)) + return 1; return 0; } @@ -893,6 +899,25 @@ static void i2c_init_recovery(struct i2c_adapter *adap) adap->bus_recovery_info = NULL; } +static int i2c_smbus_host_notify_to_irq(const struct i2c_client *client) +{ + struct i2c_adapter *adap = client->adapter; + unsigned int irq; + + if (!adap->host_notify_domain) + return -ENXIO; + + if (client->flags & I2C_CLIENT_TEN) + return -EINVAL; + + irq = irq_find_mapping(adap->host_notify_domain, client->addr); + if (!irq) + irq = irq_create_mapping(adap->host_notify_domain, + client->addr); + + return irq > 0 ? irq : -ENXIO; +} + static int i2c_device_probe(struct device *dev) { struct i2c_client *client = i2c_verify_client(dev); @@ -914,6 +939,14 @@ static int i2c_device_probe(struct device *dev) } if (irq == -EPROBE_DEFER) return irq; + /* + * ACPI and OF did not find any useful IRQ, try to see + * if Host Notify can be used. + */ + if (irq < 0) { + dev_dbg(dev, "Using Host Notify IRQ\n"); + irq = i2c_smbus_host_notify_to_irq(client); + } if (irq < 0) irq = 0; @@ -921,7 +954,13 @@ static int i2c_device_probe(struct device *dev) } driver = to_i2c_driver(dev->driver); - if (!driver->probe || !driver->id_table) + + /* + * An I2C ID table is not mandatory, if and only if, a suitable Device + * Tree match table entry is supplied for the probing device. + */ + if (!driver->id_table && + !i2c_of_match_device(dev->driver->of_match_table, client)) return -ENODEV; if (client->flags & I2C_CLIENT_WAKE) { @@ -956,7 +995,18 @@ static int i2c_device_probe(struct device *dev) if (status == -EPROBE_DEFER) goto err_clear_wakeup_irq; - status = driver->probe(client, i2c_match_id(driver->id_table, client)); + /* + * When there are no more users of probe(), + * rename probe_new to probe. + */ + if (driver->probe_new) + status = driver->probe_new(client); + else if (driver->probe) + status = driver->probe(client, + i2c_match_id(driver->id_table, client)); + else + status = -EINVAL; + if (status) goto err_detach_pm_domain; @@ -1767,6 +1817,52 @@ struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node) return adapter; } EXPORT_SYMBOL(of_get_i2c_adapter_by_node); + +static const struct of_device_id* +i2c_of_match_device_sysfs(const struct of_device_id *matches, + struct i2c_client *client) +{ + const char *name; + + for (; matches->compatible[0]; matches++) { + /* + * Adding devices through the i2c sysfs interface provides us + * a string to match which may be compatible with the device + * tree compatible strings, however with no actual of_node the + * of_match_device() will not match + */ + if (sysfs_streq(client->name, matches->compatible)) + return matches; + + name = strchr(matches->compatible, ','); + if (!name) + name = matches->compatible; + else + name++; + + if (sysfs_streq(client->name, name)) + return matches; + } + + return NULL; +} + +const struct of_device_id +*i2c_of_match_device(const struct of_device_id *matches, + struct i2c_client *client) +{ + const struct of_device_id *match; + + if (!(client && matches)) + return NULL; + + match = of_match_device(matches, &client->dev); + if (match) + return match; + + return i2c_of_match_device_sysfs(matches, client); +} +EXPORT_SYMBOL_GPL(i2c_of_match_device); #else static void of_i2c_register_devices(struct i2c_adapter *adap) { } #endif /* CONFIG_OF */ @@ -1800,6 +1896,79 @@ static const struct i2c_lock_operations i2c_adapter_lock_ops = { .unlock_bus = i2c_adapter_unlock_bus, }; +static void i2c_host_notify_irq_teardown(struct i2c_adapter *adap) +{ + struct irq_domain *domain = adap->host_notify_domain; + irq_hw_number_t hwirq; + + if (!domain) + return; + + for (hwirq = 0 ; hwirq < I2C_ADDR_7BITS_COUNT ; hwirq++) + irq_dispose_mapping(irq_find_mapping(domain, hwirq)); + + irq_domain_remove(domain); + adap->host_notify_domain = NULL; +} + +static int i2c_host_notify_irq_map(struct irq_domain *h, + unsigned int virq, + irq_hw_number_t hw_irq_num) +{ + irq_set_chip_and_handler(virq, &dummy_irq_chip, handle_simple_irq); + + return 0; +} + +static const struct irq_domain_ops i2c_host_notify_irq_ops = { + .map = i2c_host_notify_irq_map, +}; + +static int i2c_setup_host_notify_irq_domain(struct i2c_adapter *adap) +{ + struct irq_domain *domain; + + if (!i2c_check_functionality(adap, I2C_FUNC_SMBUS_HOST_NOTIFY)) + return 0; + + domain = irq_domain_create_linear(adap->dev.fwnode, + I2C_ADDR_7BITS_COUNT, + &i2c_host_notify_irq_ops, adap); + if (!domain) + return -ENOMEM; + + adap->host_notify_domain = domain; + + return 0; +} + +/** + * i2c_handle_smbus_host_notify - Forward a Host Notify event to the correct + * I2C client. + * @adap: the adapter + * @addr: the I2C address of the notifying device + * Context: can't sleep + * + * Helper function to be called from an I2C bus driver's interrupt + * handler. It will schedule the Host Notify IRQ. + */ +int i2c_handle_smbus_host_notify(struct i2c_adapter *adap, unsigned short addr) +{ + int irq; + + if (!adap) + return -EINVAL; + + irq = irq_find_mapping(adap->host_notify_domain, addr); + if (irq <= 0) + return -ENXIO; + + generic_handle_irq(irq); + + return 0; +} +EXPORT_SYMBOL_GPL(i2c_handle_smbus_host_notify); + static int i2c_register_adapter(struct i2c_adapter *adap) { int res = -EINVAL; @@ -1831,6 +2000,14 @@ static int i2c_register_adapter(struct i2c_adapter *adap) if (adap->timeout == 0) adap->timeout = HZ; + /* register soft irqs for Host Notify */ + res = i2c_setup_host_notify_irq_domain(adap); + if (res) { + pr_err("adapter '%s': can't create Host Notify IRQs (%d)\n", + adap->name, res); + goto out_list; + } + dev_set_name(&adap->dev, "i2c-%d", adap->nr); adap->dev.bus = &i2c_bus_type; adap->dev.type = &i2c_adapter_type; @@ -2068,6 +2245,8 @@ void i2c_del_adapter(struct i2c_adapter *adap) pm_runtime_disable(&adap->dev); + i2c_host_notify_irq_teardown(adap); + /* wait until all references to the device are gone * * FIXME: This is old code and should ideally be replaced by an diff --git a/drivers/i2c/i2c-smbus.c b/drivers/i2c/i2c-smbus.c index b0d2679c60d1..f9271c713d20 100644 --- a/drivers/i2c/i2c-smbus.c +++ b/drivers/i2c/i2c-smbus.c @@ -241,108 +241,6 @@ int i2c_handle_smbus_alert(struct i2c_client *ara) } EXPORT_SYMBOL_GPL(i2c_handle_smbus_alert); -static void smbus_host_notify_work(struct work_struct *work) -{ - struct alert_data alert; - struct i2c_adapter *adapter; - unsigned long flags; - u16 payload; - u8 addr; - struct smbus_host_notify *data; - - data = container_of(work, struct smbus_host_notify, work); - - spin_lock_irqsave(&data->lock, flags); - payload = data->payload; - addr = data->addr; - adapter = data->adapter; - - /* clear the pending bit and release the spinlock */ - data->pending = false; - spin_unlock_irqrestore(&data->lock, flags); - - if (!adapter || !addr) - return; - - alert.type = I2C_PROTOCOL_SMBUS_HOST_NOTIFY; - alert.addr = addr; - alert.data = payload; - - device_for_each_child(&adapter->dev, &alert, smbus_do_alert); -} - -/** - * i2c_setup_smbus_host_notify - Allocate a new smbus_host_notify for the given - * I2C adapter. - * @adapter: the adapter we want to associate a Host Notify function - * - * Returns a struct smbus_host_notify pointer on success, and NULL on failure. - * The resulting smbus_host_notify must not be freed afterwards, it is a - * managed resource already. - */ -struct smbus_host_notify *i2c_setup_smbus_host_notify(struct i2c_adapter *adap) -{ - struct smbus_host_notify *host_notify; - - host_notify = devm_kzalloc(&adap->dev, sizeof(struct smbus_host_notify), - GFP_KERNEL); - if (!host_notify) - return NULL; - - host_notify->adapter = adap; - - spin_lock_init(&host_notify->lock); - INIT_WORK(&host_notify->work, smbus_host_notify_work); - - return host_notify; -} -EXPORT_SYMBOL_GPL(i2c_setup_smbus_host_notify); - -/** - * i2c_handle_smbus_host_notify - Forward a Host Notify event to the correct - * I2C client. - * @host_notify: the struct host_notify attached to the relevant adapter - * @addr: the I2C address of the notifying device - * @data: the payload of the notification - * Context: can't sleep - * - * Helper function to be called from an I2C bus driver's interrupt - * handler. It will schedule the Host Notify work, in turn calling the - * corresponding I2C device driver's alert function. - * - * host_notify should be a valid pointer previously returned by - * i2c_setup_smbus_host_notify(). - */ -int i2c_handle_smbus_host_notify(struct smbus_host_notify *host_notify, - unsigned short addr, unsigned int data) -{ - unsigned long flags; - struct i2c_adapter *adapter; - - if (!host_notify || !host_notify->adapter) - return -EINVAL; - - adapter = host_notify->adapter; - - spin_lock_irqsave(&host_notify->lock, flags); - - if (host_notify->pending) { - spin_unlock_irqrestore(&host_notify->lock, flags); - dev_warn(&adapter->dev, "Host Notify already scheduled.\n"); - return -EBUSY; - } - - host_notify->payload = data; - host_notify->addr = addr; - - /* Mark that there is a pending notification and release the lock */ - host_notify->pending = true; - spin_unlock_irqrestore(&host_notify->lock, flags); - - return schedule_work(&host_notify->work); -} -EXPORT_SYMBOL_GPL(i2c_handle_smbus_host_notify); - module_i2c_driver(smbalert_driver); MODULE_AUTHOR("Jean Delvare "); diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig index 96de9ce5669b..10b3d17ae3ea 100644 --- a/drivers/i2c/muxes/Kconfig +++ b/drivers/i2c/muxes/Kconfig @@ -82,4 +82,15 @@ config I2C_DEMUX_PINCTRL demultiplexer that uses the pinctrl subsystem. This is useful if you want to change the I2C master at run-time depending on features. +config I2C_MUX_MLXCPLD + tristate "Mellanox CPLD based I2C multiplexer" + help + If you say yes to this option, support will be included for a + CPLD based I2C multiplexer. This driver provides access to + I2C busses connected through a MUX, which is controlled + by a CPLD register. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-mlxcpld. + endmenu diff --git a/drivers/i2c/muxes/Makefile b/drivers/i2c/muxes/Makefile index 7c267c29b191..9948fa45037f 100644 --- a/drivers/i2c/muxes/Makefile +++ b/drivers/i2c/muxes/Makefile @@ -6,6 +6,7 @@ obj-$(CONFIG_I2C_ARB_GPIO_CHALLENGE) += i2c-arb-gpio-challenge.o obj-$(CONFIG_I2C_DEMUX_PINCTRL) += i2c-demux-pinctrl.o obj-$(CONFIG_I2C_MUX_GPIO) += i2c-mux-gpio.o +obj-$(CONFIG_I2C_MUX_MLXCPLD) += i2c-mux-mlxcpld.o obj-$(CONFIG_I2C_MUX_PCA9541) += i2c-mux-pca9541.o obj-$(CONFIG_I2C_MUX_PCA954x) += i2c-mux-pca954x.o obj-$(CONFIG_I2C_MUX_PINCTRL) += i2c-mux-pinctrl.o diff --git a/drivers/i2c/muxes/i2c-mux-gpio.c b/drivers/i2c/muxes/i2c-mux-gpio.c index e5cf26eefa97..655684d621a4 100644 --- a/drivers/i2c/muxes/i2c-mux-gpio.c +++ b/drivers/i2c/muxes/i2c-mux-gpio.c @@ -21,6 +21,8 @@ struct gpiomux { struct i2c_mux_gpio_platform_data data; unsigned gpio_base; + struct gpio_desc **gpios; + int *values; }; static void i2c_mux_gpio_set(const struct gpiomux *mux, unsigned val) @@ -28,8 +30,10 @@ static void i2c_mux_gpio_set(const struct gpiomux *mux, unsigned val) int i; for (i = 0; i < mux->data.n_gpios; i++) - gpio_set_value_cansleep(mux->gpio_base + mux->data.gpios[i], - val & (1 << i)); + mux->values[i] = (val >> i) & 1; + + gpiod_set_array_value_cansleep(mux->data.n_gpios, + mux->gpios, mux->values); } static int i2c_mux_gpio_select(struct i2c_mux_core *muxc, u32 chan) @@ -176,12 +180,16 @@ static int i2c_mux_gpio_probe(struct platform_device *pdev) if (!parent) return -EPROBE_DEFER; - muxc = i2c_mux_alloc(parent, &pdev->dev, mux->data.n_values, 0, 0, + muxc = i2c_mux_alloc(parent, &pdev->dev, mux->data.n_values, + mux->data.n_gpios * sizeof(*mux->gpios) + + mux->data.n_gpios * sizeof(*mux->values), 0, i2c_mux_gpio_select, NULL); if (!muxc) { ret = -ENOMEM; goto alloc_failed; } + mux->gpios = muxc->priv; + mux->values = (int *)(mux->gpios + mux->data.n_gpios); muxc->priv = mux; platform_set_drvdata(pdev, muxc); @@ -219,10 +227,12 @@ static int i2c_mux_gpio_probe(struct platform_device *pdev) goto err_request_gpio; } + gpio_desc = gpio_to_desc(gpio_base + mux->data.gpios[i]); + mux->gpios[i] = gpio_desc; + if (!muxc->mux_locked) continue; - gpio_desc = gpio_to_desc(gpio_base + mux->data.gpios[i]); gpio_dev = &gpio_desc->gdev->dev; muxc->mux_locked = i2c_root_adapter(gpio_dev) == root; } diff --git a/drivers/i2c/muxes/i2c-mux-mlxcpld.c b/drivers/i2c/muxes/i2c-mux-mlxcpld.c new file mode 100644 index 000000000000..3ab654bbfab5 --- /dev/null +++ b/drivers/i2c/muxes/i2c-mux-mlxcpld.c @@ -0,0 +1,220 @@ +/* + * drivers/i2c/muxes/i2c-mux-mlxcpld.c + * Copyright (c) 2016 Mellanox Technologies. All rights reserved. + * Copyright (c) 2016 Michael Shych + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the names of the copyright holders nor the names of its + * contributors may be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#define CPLD_MUX_MAX_NCHANS 8 + +/* mlxcpld_mux - mux control structure: + * @last_chan - last register value + * @client - I2C device client + */ +struct mlxcpld_mux { + u8 last_chan; + struct i2c_client *client; +}; + +/* MUX logic description. + * Driver can support different mux control logic, according to CPLD + * implementation. + * + * Connectivity schema. + * + * i2c-mlxcpld Digital Analog + * driver + * *--------* * -> mux1 (virt bus2) -> mux -> | + * | I2CLPC | i2c physical * -> mux2 (virt bus3) -> mux -> | + * | bridge | bus 1 *---------* | + * | logic |---------------------> * mux reg * | + * | in CPLD| *---------* | + * *--------* i2c-mux-mlxpcld ^ * -> muxn (virt busn) -> mux -> | + * | driver | | + * | *---------------* | Devices + * | * CPLD (i2c bus)* select | + * | * registers for *--------* + * | * mux selection * deselect + * | *---------------* + * | | + * <--------> <-----------> + * i2c cntrl Board cntrl reg + * reg space space (mux select, + * IO, LED, WD, info) + * + */ + +static const struct i2c_device_id mlxcpld_mux_id[] = { + { "mlxcpld_mux_module", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, mlxcpld_mux_id); + +/* Write to mux register. Don't use i2c_transfer() and i2c_smbus_xfer() + * for this as they will try to lock adapter a second time. + */ +static int mlxcpld_mux_reg_write(struct i2c_adapter *adap, + struct i2c_client *client, u8 val) +{ + struct mlxcpld_mux_plat_data *pdata = dev_get_platdata(&client->dev); + + if (adap->algo->master_xfer) { + struct i2c_msg msg; + u8 msgbuf[] = {pdata->sel_reg_addr, val}; + + msg.addr = client->addr; + msg.flags = 0; + msg.len = 2; + msg.buf = msgbuf; + return __i2c_transfer(adap, &msg, 1); + } else if (adap->algo->smbus_xfer) { + union i2c_smbus_data data; + + data.byte = val; + return adap->algo->smbus_xfer(adap, client->addr, + client->flags, I2C_SMBUS_WRITE, + pdata->sel_reg_addr, + I2C_SMBUS_BYTE_DATA, &data); + } else + return -ENODEV; +} + +static int mlxcpld_mux_select_chan(struct i2c_mux_core *muxc, u32 chan) +{ + struct mlxcpld_mux *data = i2c_mux_priv(muxc); + struct i2c_client *client = data->client; + u8 regval = chan + 1; + int err = 0; + + /* Only select the channel if its different from the last channel */ + if (data->last_chan != regval) { + err = mlxcpld_mux_reg_write(muxc->parent, client, regval); + if (err) + data->last_chan = 0; + else + data->last_chan = regval; + } + + return err; +} + +static int mlxcpld_mux_deselect(struct i2c_mux_core *muxc, u32 chan) +{ + struct mlxcpld_mux *data = i2c_mux_priv(muxc); + struct i2c_client *client = data->client; + + /* Deselect active channel */ + data->last_chan = 0; + + return mlxcpld_mux_reg_write(muxc->parent, client, data->last_chan); +} + +/* Probe/reomove functions */ +static int mlxcpld_mux_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct i2c_adapter *adap = to_i2c_adapter(client->dev.parent); + struct mlxcpld_mux_plat_data *pdata = dev_get_platdata(&client->dev); + struct i2c_mux_core *muxc; + int num, force; + struct mlxcpld_mux *data; + int err; + + if (!pdata) + return -EINVAL; + + if (!i2c_check_functionality(adap, I2C_FUNC_SMBUS_WRITE_BYTE_DATA)) + return -ENODEV; + + muxc = i2c_mux_alloc(adap, &client->dev, CPLD_MUX_MAX_NCHANS, + sizeof(*data), 0, mlxcpld_mux_select_chan, + mlxcpld_mux_deselect); + if (!muxc) + return -ENOMEM; + + data = i2c_mux_priv(muxc); + i2c_set_clientdata(client, muxc); + data->client = client; + data->last_chan = 0; /* force the first selection */ + + /* Create an adapter for each channel. */ + for (num = 0; num < CPLD_MUX_MAX_NCHANS; num++) { + if (num >= pdata->num_adaps) + /* discard unconfigured channels */ + break; + + force = pdata->adap_ids[num]; + + err = i2c_mux_add_adapter(muxc, force, num, 0); + if (err) + goto virt_reg_failed; + } + + return 0; + +virt_reg_failed: + i2c_mux_del_adapters(muxc); + return err; +} + +static int mlxcpld_mux_remove(struct i2c_client *client) +{ + struct i2c_mux_core *muxc = i2c_get_clientdata(client); + + i2c_mux_del_adapters(muxc); + return 0; +} + +static struct i2c_driver mlxcpld_mux_driver = { + .driver = { + .name = "mlxcpld-mux", + }, + .probe = mlxcpld_mux_probe, + .remove = mlxcpld_mux_remove, + .id_table = mlxcpld_mux_id, +}; + +module_i2c_driver(mlxcpld_mux_driver); + +MODULE_AUTHOR("Michael Shych (michaels@mellanox.com)"); +MODULE_DESCRIPTION("Mellanox I2C-CPLD-MUX driver"); +MODULE_LICENSE("Dual BSD/GPL"); +MODULE_ALIAS("platform:i2c-mux-mlxcpld"); diff --git a/drivers/i2c/muxes/i2c-mux-pca954x.c b/drivers/i2c/muxes/i2c-mux-pca954x.c index 8bc3d36d2837..9a348ee4dc14 100644 --- a/drivers/i2c/muxes/i2c-mux-pca954x.c +++ b/drivers/i2c/muxes/i2c-mux-pca954x.c @@ -35,6 +35,7 @@ * warranty of any kind, whether express or implied. */ +#include #include #include #include @@ -120,6 +121,21 @@ static const struct i2c_device_id pca954x_id[] = { }; MODULE_DEVICE_TABLE(i2c, pca954x_id); +#ifdef CONFIG_ACPI +static const struct acpi_device_id pca954x_acpi_ids[] = { + { .id = "PCA9540", .driver_data = pca_9540 }, + { .id = "PCA9542", .driver_data = pca_9540 }, + { .id = "PCA9543", .driver_data = pca_9543 }, + { .id = "PCA9544", .driver_data = pca_9544 }, + { .id = "PCA9545", .driver_data = pca_9545 }, + { .id = "PCA9546", .driver_data = pca_9545 }, + { .id = "PCA9547", .driver_data = pca_9547 }, + { .id = "PCA9548", .driver_data = pca_9548 }, + { } +}; +MODULE_DEVICE_TABLE(acpi, pca954x_acpi_ids); +#endif + #ifdef CONFIG_OF static const struct of_device_id pca954x_of_match[] = { { .compatible = "nxp,pca9540", .data = &chips[pca_9540] }, @@ -245,8 +261,17 @@ static int pca954x_probe(struct i2c_client *client, match = of_match_device(of_match_ptr(pca954x_of_match), &client->dev); if (match) data->chip = of_device_get_match_data(&client->dev); - else + else if (id) data->chip = &chips[id->driver_data]; + else { + const struct acpi_device_id *acpi_id; + + acpi_id = acpi_match_device(ACPI_PTR(pca954x_acpi_ids), + &client->dev); + if (!acpi_id) + return -ENODEV; + data->chip = &chips[acpi_id->driver_data]; + } data->last_chan = 0; /* force the first selection */ @@ -321,6 +346,7 @@ static struct i2c_driver pca954x_driver = { .name = "pca954x", .pm = &pca954x_pm, .of_match_table = of_match_ptr(pca954x_of_match), + .acpi_match_table = ACPI_PTR(pca954x_acpi_ids), }, .probe = pca954x_probe, .remove = pca954x_remove, diff --git a/drivers/mfd/88pm860x-core.c b/drivers/mfd/88pm860x-core.c index 25e1aafae60c..227b99018657 100644 --- a/drivers/mfd/88pm860x-core.c +++ b/drivers/mfd/88pm860x-core.c @@ -1132,8 +1132,7 @@ static int pm860x_dt_init(struct device_node *np, return 0; } -static int pm860x_probe(struct i2c_client *client, - const struct i2c_device_id *id) +static int pm860x_probe(struct i2c_client *client) { struct pm860x_platform_data *pdata = dev_get_platdata(&client->dev); struct device_node *node = client->dev.of_node; @@ -1259,7 +1258,7 @@ static struct i2c_driver pm860x_driver = { .pm = &pm860x_pm_ops, .of_match_table = pm860x_dt_ids, }, - .probe = pm860x_probe, + .probe_new = pm860x_probe, .remove = pm860x_remove, .id_table = pm860x_id_table, }; diff --git a/include/linux/i2c-smbus.h b/include/linux/i2c-smbus.h index c2e3324f9468..a1385023a29b 100644 --- a/include/linux/i2c-smbus.h +++ b/include/linux/i2c-smbus.h @@ -50,31 +50,4 @@ struct i2c_client *i2c_setup_smbus_alert(struct i2c_adapter *adapter, struct i2c_smbus_alert_setup *setup); int i2c_handle_smbus_alert(struct i2c_client *ara); -/** - * smbus_host_notify - internal structure used by the Host Notify mechanism. - * @adapter: the I2C adapter associated with this struct - * @work: worker used to schedule the IRQ in the slave device - * @lock: spinlock to check if a notification is already pending - * @pending: flag set when a notification is pending (any new notification will - * be rejected if pending is true) - * @payload: the actual payload of the Host Notify event - * @addr: the address of the slave device which raised the notification - * - * This struct needs to be allocated by i2c_setup_smbus_host_notify() and does - * not need to be freed. Internally, i2c_setup_smbus_host_notify() uses a - * managed resource to clean this up when the adapter get released. - */ -struct smbus_host_notify { - struct i2c_adapter *adapter; - struct work_struct work; - spinlock_t lock; - bool pending; - u16 payload; - u8 addr; -}; - -struct smbus_host_notify *i2c_setup_smbus_host_notify(struct i2c_adapter *adap); -int i2c_handle_smbus_host_notify(struct smbus_host_notify *host_notify, - unsigned short addr, unsigned int data); - #endif /* _LINUX_I2C_SMBUS_H */ diff --git a/include/linux/i2c.h b/include/linux/i2c.h index 6422eef428c4..b2109c522dec 100644 --- a/include/linux/i2c.h +++ b/include/linux/i2c.h @@ -30,6 +30,7 @@ #include /* for struct device */ #include /* for completion */ #include +#include /* for Host Notify IRQ */ #include /* for struct device_node */ #include /* for swab16 */ #include @@ -135,7 +136,8 @@ enum i2c_alert_protocol { * struct i2c_driver - represent an I2C device driver * @class: What kind of i2c device we instantiate (for detect) * @attach_adapter: Callback for bus addition (deprecated) - * @probe: Callback for device binding + * @probe: Callback for device binding - soon to be deprecated + * @probe_new: New callback for device binding * @remove: Callback for device unbinding * @shutdown: Callback for device shutdown * @alert: Alert callback, for example for the SMBus alert protocol @@ -178,6 +180,11 @@ struct i2c_driver { int (*probe)(struct i2c_client *, const struct i2c_device_id *); int (*remove)(struct i2c_client *); + /* New driver model interface to aid the seamless removal of the + * current probe()'s, more commonly unused than used second parameter. + */ + int (*probe_new)(struct i2c_client *); + /* driver model interfaces that don't relate to enumeration */ void (*shutdown)(struct i2c_client *); @@ -243,6 +250,8 @@ struct i2c_client { extern struct i2c_client *i2c_verify_client(struct device *dev); extern struct i2c_adapter *i2c_verify_adapter(struct device *dev); +extern const struct i2c_device_id *i2c_match_id(const struct i2c_device_id *id, + const struct i2c_client *client); static inline struct i2c_client *kobj_to_i2c_client(struct kobject *kobj) { @@ -567,6 +576,8 @@ struct i2c_adapter { struct i2c_bus_recovery_info *bus_recovery_info; const struct i2c_adapter_quirks *quirks; + + struct irq_domain *host_notify_domain; }; #define to_i2c_adapter(d) container_of(d, struct i2c_adapter, dev) @@ -739,6 +750,7 @@ static inline u8 i2c_8bit_addr_from_msg(const struct i2c_msg *msg) return (msg->addr << 1) | (msg->flags & I2C_M_RD ? 1 : 0); } +int i2c_handle_smbus_host_notify(struct i2c_adapter *adap, unsigned short addr); /** * module_i2c_driver() - Helper macro for registering a modular I2C driver * @__i2c_driver: i2c_driver struct @@ -774,6 +786,10 @@ extern struct i2c_adapter *of_find_i2c_adapter_by_node(struct device_node *node) /* must call i2c_put_adapter() when done with returned i2c_adapter device */ struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node *node); +extern const struct of_device_id +*i2c_of_match_device(const struct of_device_id *matches, + struct i2c_client *client); + #else static inline struct i2c_client *of_find_i2c_device_by_node(struct device_node *node) @@ -790,6 +806,14 @@ static inline struct i2c_adapter *of_get_i2c_adapter_by_node(struct device_node { return NULL; } + +static inline const struct of_device_id +*i2c_of_match_device(const struct of_device_id *matches, + struct i2c_client *client) +{ + return NULL; +} + #endif /* CONFIG_OF */ #if IS_ENABLED(CONFIG_ACPI) diff --git a/include/linux/i2c/mlxcpld.h b/include/linux/i2c/mlxcpld.h new file mode 100644 index 000000000000..b08dcb183fca --- /dev/null +++ b/include/linux/i2c/mlxcpld.h @@ -0,0 +1,52 @@ +/* + * mlxcpld.h - Mellanox I2C multiplexer support in CPLD + * + * Copyright (c) 2016 Mellanox Technologies. All rights reserved. + * Copyright (c) 2016 Michael Shych + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * 3. Neither the names of the copyright holders nor the names of its + * contributors may be used to endorse or promote products derived from + * this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE + * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR + * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF + * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS + * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN + * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGE. + */ + +#ifndef _LINUX_I2C_MLXCPLD_H +#define _LINUX_I2C_MLXCPLD_H + +/* Platform data for the CPLD I2C multiplexers */ + +/* mlxcpld_mux_plat_data - per mux data, used with i2c_register_board_info + * @adap_ids - adapter array + * @num_adaps - number of adapters + * @sel_reg_addr - mux select register offset in CPLD space + */ +struct mlxcpld_mux_plat_data { + int *adap_ids; + int num_adaps; + int sel_reg_addr; +}; + +#endif /* _LINUX_I2C_MLXCPLD_H */