phy: intel: Add Keem Bay eMMC PHY support
Add support for eMMC PHY on Intel Keem Bay SoC. Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20200913235522.4316-4-wan.ahmad.zainie.wan.mohamad@intel.com Signed-off-by: Vinod Koul <vkoul@kernel.org>
This commit is contained in:
parent
9580b22aca
commit
885c4f4d6c
|
@ -2,6 +2,18 @@
|
|||
#
|
||||
# Phy drivers for Intel platforms
|
||||
#
|
||||
config PHY_INTEL_KEEMBAY_EMMC
|
||||
tristate "Intel Keem Bay EMMC PHY driver"
|
||||
depends on (OF && ARM64) || COMPILE_TEST
|
||||
depends on HAS_IOMEM
|
||||
select GENERIC_PHY
|
||||
select REGMAP_MMIO
|
||||
help
|
||||
Choose this option if you have an Intel Keem Bay SoC.
|
||||
|
||||
To compile this driver as a module, choose M here: the module
|
||||
will be called phy-keembay-emmc.ko.
|
||||
|
||||
config PHY_INTEL_LGM_COMBO
|
||||
bool "Intel Lightning Mountain ComboPHY driver"
|
||||
depends on X86 || COMPILE_TEST
|
||||
|
|
|
@ -1,3 +1,4 @@
|
|||
# SPDX-License-Identifier: GPL-2.0
|
||||
obj-$(CONFIG_PHY_INTEL_KEEMBAY_EMMC) += phy-intel-keembay-emmc.o
|
||||
obj-$(CONFIG_PHY_INTEL_LGM_COMBO) += phy-intel-lgm-combo.o
|
||||
obj-$(CONFIG_PHY_INTEL_LGM_EMMC) += phy-intel-lgm-emmc.o
|
||||
|
|
307
drivers/phy/intel/phy-intel-keembay-emmc.c
Normal file
307
drivers/phy/intel/phy-intel-keembay-emmc.c
Normal file
|
@ -0,0 +1,307 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-only
|
||||
/*
|
||||
* Intel Keem Bay eMMC PHY driver
|
||||
* Copyright (C) 2020 Intel Corporation
|
||||
*/
|
||||
|
||||
#include <linux/bitfield.h>
|
||||
#include <linux/clk.h>
|
||||
#include <linux/delay.h>
|
||||
#include <linux/mfd/syscon.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/of.h>
|
||||
#include <linux/of_address.h>
|
||||
#include <linux/phy/phy.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/regmap.h>
|
||||
|
||||
/* eMMC/SD/SDIO core/phy configuration registers */
|
||||
#define PHY_CFG_0 0x24
|
||||
#define SEL_DLY_TXCLK_MASK BIT(29)
|
||||
#define OTAP_DLY_ENA_MASK BIT(27)
|
||||
#define OTAP_DLY_SEL_MASK GENMASK(26, 23)
|
||||
#define DLL_EN_MASK BIT(10)
|
||||
#define PWR_DOWN_MASK BIT(0)
|
||||
|
||||
#define PHY_CFG_2 0x2c
|
||||
#define SEL_FREQ_MASK GENMASK(12, 10)
|
||||
|
||||
#define PHY_STAT 0x40
|
||||
#define CAL_DONE_MASK BIT(6)
|
||||
#define IS_CALDONE(x) ((x) & CAL_DONE_MASK)
|
||||
#define DLL_RDY_MASK BIT(5)
|
||||
#define IS_DLLRDY(x) ((x) & DLL_RDY_MASK)
|
||||
|
||||
/* From ACS_eMMC51_16nFFC_RO1100_Userguide_v1p0.pdf p17 */
|
||||
#define FREQSEL_200M_170M 0x0
|
||||
#define FREQSEL_170M_140M 0x1
|
||||
#define FREQSEL_140M_110M 0x2
|
||||
#define FREQSEL_110M_80M 0x3
|
||||
#define FREQSEL_80M_50M 0x4
|
||||
|
||||
struct keembay_emmc_phy {
|
||||
struct regmap *syscfg;
|
||||
struct clk *emmcclk;
|
||||
};
|
||||
|
||||
static const struct regmap_config keembay_regmap_config = {
|
||||
.reg_bits = 32,
|
||||
.val_bits = 32,
|
||||
.reg_stride = 4,
|
||||
};
|
||||
|
||||
static int keembay_emmc_phy_power(struct phy *phy, bool on_off)
|
||||
{
|
||||
struct keembay_emmc_phy *priv = phy_get_drvdata(phy);
|
||||
unsigned int caldone;
|
||||
unsigned int dllrdy;
|
||||
unsigned int freqsel;
|
||||
unsigned int mhz;
|
||||
int ret;
|
||||
|
||||
/*
|
||||
* Keep phyctrl_pdb and phyctrl_endll low to allow
|
||||
* initialization of CALIO state M/C DFFs
|
||||
*/
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, PWR_DOWN_MASK,
|
||||
FIELD_PREP(PWR_DOWN_MASK, 0));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "CALIO power down bar failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, DLL_EN_MASK,
|
||||
FIELD_PREP(DLL_EN_MASK, 0));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "turn off the dll failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/* Already finish power off above */
|
||||
if (!on_off)
|
||||
return 0;
|
||||
|
||||
mhz = DIV_ROUND_CLOSEST(clk_get_rate(priv->emmcclk), 1000000);
|
||||
if (mhz <= 200 && mhz >= 170)
|
||||
freqsel = FREQSEL_200M_170M;
|
||||
else if (mhz <= 170 && mhz >= 140)
|
||||
freqsel = FREQSEL_170M_140M;
|
||||
else if (mhz <= 140 && mhz >= 110)
|
||||
freqsel = FREQSEL_140M_110M;
|
||||
else if (mhz <= 110 && mhz >= 80)
|
||||
freqsel = FREQSEL_110M_80M;
|
||||
else if (mhz <= 80 && mhz >= 50)
|
||||
freqsel = FREQSEL_80M_50M;
|
||||
else
|
||||
freqsel = 0x0;
|
||||
|
||||
if (mhz < 50 || mhz > 200)
|
||||
dev_warn(&phy->dev, "Unsupported rate: %d MHz\n", mhz);
|
||||
|
||||
/*
|
||||
* According to the user manual, calpad calibration
|
||||
* cycle takes more than 2us without the minimal recommended
|
||||
* value, so we may need a little margin here
|
||||
*/
|
||||
udelay(5);
|
||||
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, PWR_DOWN_MASK,
|
||||
FIELD_PREP(PWR_DOWN_MASK, 1));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "CALIO power down bar failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/*
|
||||
* According to the user manual, it asks driver to wait 5us for
|
||||
* calpad busy trimming. However it is documented that this value is
|
||||
* PVT(A.K.A. process, voltage and temperature) relevant, so some
|
||||
* failure cases are found which indicates we should be more tolerant
|
||||
* to calpad busy trimming.
|
||||
*/
|
||||
ret = regmap_read_poll_timeout(priv->syscfg, PHY_STAT,
|
||||
caldone, IS_CALDONE(caldone),
|
||||
0, 50);
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "caldone failed, ret=%d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/* Set the frequency of the DLL operation */
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_2, SEL_FREQ_MASK,
|
||||
FIELD_PREP(SEL_FREQ_MASK, freqsel));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "set the frequency of dll failed:%d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/* Turn on the DLL */
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, DLL_EN_MASK,
|
||||
FIELD_PREP(DLL_EN_MASK, 1));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "turn on the dll failed: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/*
|
||||
* We turned on the DLL even though the rate was 0 because we the
|
||||
* clock might be turned on later. ...but we can't wait for the DLL
|
||||
* to lock when the rate is 0 because it will never lock with no
|
||||
* input clock.
|
||||
*
|
||||
* Technically we should be checking the lock later when the clock
|
||||
* is turned on, but for now we won't.
|
||||
*/
|
||||
if (mhz == 0)
|
||||
return 0;
|
||||
|
||||
/*
|
||||
* After enabling analog DLL circuits docs say that we need 10.2 us if
|
||||
* our source clock is at 50 MHz and that lock time scales linearly
|
||||
* with clock speed. If we are powering on the PHY and the card clock
|
||||
* is super slow (like 100kHz) this could take as long as 5.1 ms as
|
||||
* per the math: 10.2 us * (50000000 Hz / 100000 Hz) => 5.1 ms
|
||||
* hopefully we won't be running at 100 kHz, but we should still make
|
||||
* sure we wait long enough.
|
||||
*
|
||||
* NOTE: There appear to be corner cases where the DLL seems to take
|
||||
* extra long to lock for reasons that aren't understood. In some
|
||||
* extreme cases we've seen it take up to over 10ms (!). We'll be
|
||||
* generous and give it 50ms.
|
||||
*/
|
||||
ret = regmap_read_poll_timeout(priv->syscfg, PHY_STAT,
|
||||
dllrdy, IS_DLLRDY(dllrdy),
|
||||
0, 50 * USEC_PER_MSEC);
|
||||
if (ret)
|
||||
dev_err(&phy->dev, "dllrdy failed, ret=%d\n", ret);
|
||||
|
||||
return ret;
|
||||
}
|
||||
|
||||
static int keembay_emmc_phy_init(struct phy *phy)
|
||||
{
|
||||
struct keembay_emmc_phy *priv = phy_get_drvdata(phy);
|
||||
|
||||
/*
|
||||
* We purposely get the clock here and not in probe to avoid the
|
||||
* circular dependency problem. We expect:
|
||||
* - PHY driver to probe
|
||||
* - SDHCI driver to start probe
|
||||
* - SDHCI driver to register it's clock
|
||||
* - SDHCI driver to get the PHY
|
||||
* - SDHCI driver to init the PHY
|
||||
*
|
||||
* The clock is optional, so upon any error just return it like
|
||||
* any other error to user.
|
||||
*/
|
||||
priv->emmcclk = clk_get_optional(&phy->dev, "emmcclk");
|
||||
|
||||
return PTR_ERR_OR_ZERO(priv->emmcclk);
|
||||
}
|
||||
|
||||
static int keembay_emmc_phy_exit(struct phy *phy)
|
||||
{
|
||||
struct keembay_emmc_phy *priv = phy_get_drvdata(phy);
|
||||
|
||||
clk_put(priv->emmcclk);
|
||||
|
||||
return 0;
|
||||
};
|
||||
|
||||
static int keembay_emmc_phy_power_on(struct phy *phy)
|
||||
{
|
||||
struct keembay_emmc_phy *priv = phy_get_drvdata(phy);
|
||||
int ret;
|
||||
|
||||
/* Delay chain based txclk: enable */
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, SEL_DLY_TXCLK_MASK,
|
||||
FIELD_PREP(SEL_DLY_TXCLK_MASK, 1));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "ERROR: delay chain txclk set: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/* Output tap delay: enable */
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, OTAP_DLY_ENA_MASK,
|
||||
FIELD_PREP(OTAP_DLY_ENA_MASK, 1));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "ERROR: output tap delay set: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/* Output tap delay */
|
||||
ret = regmap_update_bits(priv->syscfg, PHY_CFG_0, OTAP_DLY_SEL_MASK,
|
||||
FIELD_PREP(OTAP_DLY_SEL_MASK, 2));
|
||||
if (ret) {
|
||||
dev_err(&phy->dev, "ERROR: output tap delay select: %d\n", ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
/* Power up eMMC phy analog blocks */
|
||||
return keembay_emmc_phy_power(phy, true);
|
||||
}
|
||||
|
||||
static int keembay_emmc_phy_power_off(struct phy *phy)
|
||||
{
|
||||
/* Power down eMMC phy analog blocks */
|
||||
return keembay_emmc_phy_power(phy, false);
|
||||
}
|
||||
|
||||
static const struct phy_ops ops = {
|
||||
.init = keembay_emmc_phy_init,
|
||||
.exit = keembay_emmc_phy_exit,
|
||||
.power_on = keembay_emmc_phy_power_on,
|
||||
.power_off = keembay_emmc_phy_power_off,
|
||||
.owner = THIS_MODULE,
|
||||
};
|
||||
|
||||
static int keembay_emmc_phy_probe(struct platform_device *pdev)
|
||||
{
|
||||
struct device *dev = &pdev->dev;
|
||||
struct device_node *np = dev->of_node;
|
||||
struct keembay_emmc_phy *priv;
|
||||
struct phy *generic_phy;
|
||||
struct phy_provider *phy_provider;
|
||||
void __iomem *base;
|
||||
|
||||
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
|
||||
if (!priv)
|
||||
return -ENOMEM;
|
||||
|
||||
base = devm_platform_ioremap_resource(pdev, 0);
|
||||
if (IS_ERR(base))
|
||||
return PTR_ERR(base);
|
||||
|
||||
priv->syscfg = devm_regmap_init_mmio(dev, base, &keembay_regmap_config);
|
||||
if (IS_ERR(priv->syscfg))
|
||||
return PTR_ERR(priv->syscfg);
|
||||
|
||||
generic_phy = devm_phy_create(dev, np, &ops);
|
||||
if (IS_ERR(generic_phy))
|
||||
return dev_err_probe(dev, PTR_ERR(generic_phy),
|
||||
"failed to create PHY\n");
|
||||
|
||||
phy_set_drvdata(generic_phy, priv);
|
||||
phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
|
||||
|
||||
return PTR_ERR_OR_ZERO(phy_provider);
|
||||
}
|
||||
|
||||
static const struct of_device_id keembay_emmc_phy_dt_ids[] = {
|
||||
{ .compatible = "intel,keembay-emmc-phy" },
|
||||
{}
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, keembay_emmc_phy_dt_ids);
|
||||
|
||||
static struct platform_driver keembay_emmc_phy_driver = {
|
||||
.probe = keembay_emmc_phy_probe,
|
||||
.driver = {
|
||||
.name = "keembay-emmc-phy",
|
||||
.of_match_table = keembay_emmc_phy_dt_ids,
|
||||
},
|
||||
};
|
||||
module_platform_driver(keembay_emmc_phy_driver);
|
||||
|
||||
MODULE_AUTHOR("Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>");
|
||||
MODULE_DESCRIPTION("Intel Keem Bay eMMC PHY driver");
|
||||
MODULE_LICENSE("GPL v2");
|
Loading…
Reference in a new issue