pwm: add pca9685 driver
Add pwm driver for the NXP pca9685 16 channel pwm-led controller. The driver is really barebones at this stage. E.g. the OE' pin and therefore the corresponding registers are not supported. The driver was tested on a HW where this pin is tied to GND. Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de> [thierry.reding@gmail.com: style and whitespace cleanups] Signed-off-by: Thierry Reding <thierry.reding@gmail.com>hifive-unleashed-5.1
Steffen Trumtrar
Thierry Reding
parent
8796f9c565
commit
88b613e623
|
|
@ -0,0 +1,27 @@
|
|||
NXP PCA9685 16-channel 12-bit PWM LED controller
|
||||
================================================
|
||||
|
||||
Required properties:
|
||||
- compatible: "nxp,pca9685-pwm"
|
||||
- #pwm-cells: should be 2. The first cell specifies the per-chip index
|
||||
of the PWM to use and the second cell is the period in nanoseconds.
|
||||
The index 16 is the ALLCALL channel, that sets all PWM channels at the same
|
||||
time.
|
||||
|
||||
Optional properties:
|
||||
- invert (bool): boolean to enable inverted logic
|
||||
- open-drain (bool): boolean to configure outputs with open-drain structure;
|
||||
if omitted use totem-pole structure
|
||||
|
||||
Example:
|
||||
|
||||
For LEDs that are directly connected to the PCA, the following setting is
|
||||
applicable:
|
||||
|
||||
pca: pca@41 {
|
||||
compatible = "nxp,pca9685-pwm";
|
||||
#pwm-cells = <2>;
|
||||
reg = <0x41>;
|
||||
invert;
|
||||
open-drain;
|
||||
};
|
||||
|
|
@ -97,6 +97,15 @@ config PWM_MXS
|
|||
To compile this driver as a module, choose M here: the module
|
||||
will be called pwm-mxs.
|
||||
|
||||
config PWM_PCA9685
|
||||
tristate "NXP PCA9685 PWM driver"
|
||||
depends on OF && REGMAP_I2C
|
||||
help
|
||||
Generic PWM framework driver for NXP PCA9685 LED controller.
|
||||
|
||||
To compile this driver as a module, choose M here: the module
|
||||
will be called pwm-pca9685.
|
||||
|
||||
config PWM_PUV3
|
||||
tristate "PKUnity NetBook-0916 PWM support"
|
||||
depends on ARCH_PUV3
|
||||
|
|
|
|||
|
|
@ -6,6 +6,7 @@ obj-$(CONFIG_PWM_IMX) += pwm-imx.o
|
|||
obj-$(CONFIG_PWM_JZ4740) += pwm-jz4740.o
|
||||
obj-$(CONFIG_PWM_LPC32XX) += pwm-lpc32xx.o
|
||||
obj-$(CONFIG_PWM_MXS) += pwm-mxs.o
|
||||
obj-$(CONFIG_PWM_PCA9685) += pwm-pca9685.o
|
||||
obj-$(CONFIG_PWM_PUV3) += pwm-puv3.o
|
||||
obj-$(CONFIG_PWM_PXA) += pwm-pxa.o
|
||||
obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,298 @@
|
|||
/*
|
||||
* Driver for PCA9685 16-channel 12-bit PWM LED controller
|
||||
*
|
||||
* Copyright (C) 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de>
|
||||
*
|
||||
* based on the pwm-twl-led.c driver
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms of the GNU General Public License version 2 as published by
|
||||
* the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope that it will be useful, but WITHOUT
|
||||
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
|
||||
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
|
||||
* more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License along with
|
||||
* this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
*/
|
||||
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/module.h>
|
||||
#include <linux/platform_device.h>
|
||||
#include <linux/pwm.h>
|
||||
#include <linux/regmap.h>
|
||||
#include <linux/slab.h>
|
||||
|
||||
#define PCA9685_MODE1 0x00
|
||||
#define PCA9685_MODE2 0x01
|
||||
#define PCA9685_SUBADDR1 0x02
|
||||
#define PCA9685_SUBADDR2 0x03
|
||||
#define PCA9685_SUBADDR3 0x04
|
||||
#define PCA9685_ALLCALLADDR 0x05
|
||||
#define PCA9685_LEDX_ON_L 0x06
|
||||
#define PCA9685_LEDX_ON_H 0x07
|
||||
#define PCA9685_LEDX_OFF_L 0x08
|
||||
#define PCA9685_LEDX_OFF_H 0x09
|
||||
|
||||
#define PCA9685_ALL_LED_ON_L 0xFA
|
||||
#define PCA9685_ALL_LED_ON_H 0xFB
|
||||
#define PCA9685_ALL_LED_OFF_L 0xFC
|
||||
#define PCA9685_ALL_LED_OFF_H 0xFD
|
||||
#define PCA9685_PRESCALE 0xFE
|
||||
|
||||
#define PCA9685_NUMREGS 0xFF
|
||||
#define PCA9685_MAXCHAN 0x10
|
||||
|
||||
#define LED_FULL (1 << 4)
|
||||
#define MODE1_SLEEP (1 << 4)
|
||||
#define MODE2_INVRT (1 << 4)
|
||||
#define MODE2_OUTDRV (1 << 2)
|
||||
|
||||
#define LED_N_ON_H(N) (PCA9685_LEDX_ON_H + (4 * (N)))
|
||||
#define LED_N_ON_L(N) (PCA9685_LEDX_ON_L + (4 * (N)))
|
||||
#define LED_N_OFF_H(N) (PCA9685_LEDX_OFF_H + (4 * (N)))
|
||||
#define LED_N_OFF_L(N) (PCA9685_LEDX_OFF_L + (4 * (N)))
|
||||
|
||||
struct pca9685 {
|
||||
struct pwm_chip chip;
|
||||
struct regmap *regmap;
|
||||
int active_cnt;
|
||||
};
|
||||
|
||||
static inline struct pca9685 *to_pca(struct pwm_chip *chip)
|
||||
{
|
||||
return container_of(chip, struct pca9685, chip);
|
||||
}
|
||||
|
||||
static int pca9685_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
|
||||
int duty_ns, int period_ns)
|
||||
{
|
||||
struct pca9685 *pca = to_pca(chip);
|
||||
unsigned long long duty;
|
||||
unsigned int reg;
|
||||
|
||||
if (duty_ns < 1) {
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_OFF_H;
|
||||
else
|
||||
reg = LED_N_OFF_H(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, LED_FULL);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
if (duty_ns == period_ns) {
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_ON_H;
|
||||
else
|
||||
reg = LED_N_ON_H(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, LED_FULL);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
duty = 4096 * (unsigned long long)duty_ns;
|
||||
duty = DIV_ROUND_UP_ULL(duty, period_ns);
|
||||
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_OFF_L;
|
||||
else
|
||||
reg = LED_N_OFF_L(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, (int)duty & 0xff);
|
||||
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_OFF_H;
|
||||
else
|
||||
reg = LED_N_OFF_H(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, ((int)duty >> 8) & 0xf);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int pca9685_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
|
||||
{
|
||||
struct pca9685 *pca = to_pca(chip);
|
||||
unsigned int reg;
|
||||
|
||||
/*
|
||||
* The PWM subsystem does not support a pre-delay.
|
||||
* So, set the ON-timeout to 0
|
||||
*/
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_ON_L;
|
||||
else
|
||||
reg = LED_N_ON_L(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, 0);
|
||||
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_ON_H;
|
||||
else
|
||||
reg = LED_N_ON_H(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, 0);
|
||||
|
||||
/*
|
||||
* Clear the full-off bit.
|
||||
* It has precedence over the others and must be off.
|
||||
*/
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_OFF_H;
|
||||
else
|
||||
reg = LED_N_OFF_H(pwm->hwpwm);
|
||||
|
||||
regmap_update_bits(pca->regmap, reg, LED_FULL, 0x0);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void pca9685_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
|
||||
{
|
||||
struct pca9685 *pca = to_pca(chip);
|
||||
unsigned int reg;
|
||||
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_OFF_H;
|
||||
else
|
||||
reg = LED_N_OFF_H(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, LED_FULL);
|
||||
|
||||
/* Clear the LED_OFF counter. */
|
||||
if (pwm->hwpwm >= PCA9685_MAXCHAN)
|
||||
reg = PCA9685_ALL_LED_OFF_L;
|
||||
else
|
||||
reg = LED_N_OFF_L(pwm->hwpwm);
|
||||
|
||||
regmap_write(pca->regmap, reg, 0x0);
|
||||
}
|
||||
|
||||
static int pca9685_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
|
||||
{
|
||||
struct pca9685 *pca = to_pca(chip);
|
||||
|
||||
if (pca->active_cnt++ == 0)
|
||||
return regmap_update_bits(pca->regmap, PCA9685_MODE1,
|
||||
MODE1_SLEEP, 0x0);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void pca9685_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
|
||||
{
|
||||
struct pca9685 *pca = to_pca(chip);
|
||||
|
||||
if (--pca->active_cnt == 0)
|
||||
regmap_update_bits(pca->regmap, PCA9685_MODE1, MODE1_SLEEP,
|
||||
0x1);
|
||||
}
|
||||
|
||||
static const struct pwm_ops pca9685_pwm_ops = {
|
||||
.enable = pca9685_pwm_enable,
|
||||
.disable = pca9685_pwm_disable,
|
||||
.config = pca9685_pwm_config,
|
||||
.request = pca9685_pwm_request,
|
||||
.free = pca9685_pwm_free,
|
||||
};
|
||||
|
||||
static struct regmap_config pca9685_regmap_i2c_config = {
|
||||
.reg_bits = 8,
|
||||
.val_bits = 8,
|
||||
.max_register = PCA9685_NUMREGS,
|
||||
.cache_type = REGCACHE_NONE,
|
||||
};
|
||||
|
||||
static int pca9685_pwm_probe(struct i2c_client *client,
|
||||
const struct i2c_device_id *id)
|
||||
{
|
||||
struct device_node *np = client->dev.of_node;
|
||||
struct pca9685 *pca;
|
||||
int ret;
|
||||
int mode2;
|
||||
|
||||
pca = devm_kzalloc(&client->dev, sizeof(*pca), GFP_KERNEL);
|
||||
if (!pca)
|
||||
return -ENOMEM;
|
||||
|
||||
pca->regmap = devm_regmap_init_i2c(client, &pca9685_regmap_i2c_config);
|
||||
if (IS_ERR(pca->regmap)) {
|
||||
ret = PTR_ERR(pca->regmap);
|
||||
dev_err(&client->dev, "Failed to initialize register map: %d\n",
|
||||
ret);
|
||||
return ret;
|
||||
}
|
||||
|
||||
i2c_set_clientdata(client, pca);
|
||||
|
||||
regmap_read(pca->regmap, PCA9685_MODE2, &mode2);
|
||||
|
||||
if (of_property_read_bool(np, "invert"))
|
||||
mode2 |= MODE2_INVRT;
|
||||
else
|
||||
mode2 &= ~MODE2_INVRT;
|
||||
|
||||
if (of_property_read_bool(np, "open-drain"))
|
||||
mode2 &= ~MODE2_OUTDRV;
|
||||
else
|
||||
mode2 |= MODE2_OUTDRV;
|
||||
|
||||
regmap_write(pca->regmap, PCA9685_MODE2, mode2);
|
||||
|
||||
/* clear all "full off" bits */
|
||||
regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_L, 0);
|
||||
regmap_write(pca->regmap, PCA9685_ALL_LED_OFF_H, 0);
|
||||
|
||||
pca->chip.ops = &pca9685_pwm_ops;
|
||||
/* add an extra channel for ALL_LED */
|
||||
pca->chip.npwm = PCA9685_MAXCHAN + 1;
|
||||
|
||||
pca->chip.dev = &client->dev;
|
||||
pca->chip.base = -1;
|
||||
pca->chip.can_sleep = true;
|
||||
|
||||
return pwmchip_add(&pca->chip);
|
||||
}
|
||||
|
||||
static int pca9685_pwm_remove(struct i2c_client *client)
|
||||
{
|
||||
struct pca9685 *pca = i2c_get_clientdata(client);
|
||||
|
||||
regmap_update_bits(pca->regmap, PCA9685_MODE1, MODE1_SLEEP, 0x1);
|
||||
|
||||
return pwmchip_remove(&pca->chip);
|
||||
}
|
||||
|
||||
static const struct i2c_device_id pca9685_id[] = {
|
||||
{ "pca9685", 0 },
|
||||
{ /* sentinel */ },
|
||||
};
|
||||
MODULE_DEVICE_TABLE(i2c, pca9685_id);
|
||||
|
||||
static const struct of_device_id pca9685_dt_ids[] = {
|
||||
{ .compatible = "nxp,pca9685-pwm", },
|
||||
{ /* sentinel */ }
|
||||
};
|
||||
MODULE_DEVICE_TABLE(of, pca9685_dt_ids);
|
||||
|
||||
static struct i2c_driver pca9685_i2c_driver = {
|
||||
.driver = {
|
||||
.name = "pca9685-pwm",
|
||||
.owner = THIS_MODULE,
|
||||
.of_match_table = pca9685_dt_ids,
|
||||
},
|
||||
.probe = pca9685_pwm_probe,
|
||||
.remove = pca9685_pwm_remove,
|
||||
.id_table = pca9685_id,
|
||||
};
|
||||
|
||||
module_i2c_driver(pca9685_i2c_driver);
|
||||
|
||||
MODULE_AUTHOR("Steffen Trumtrar <s.trumtrar@pengutronix.de>");
|
||||
MODULE_DESCRIPTION("PWM driver for PCA9685");
|
||||
MODULE_LICENSE("GPL");
|
||||
Loading…
Reference in New Issue