redonkable/alistair23-linux
redonkable/alistair23-linux
1
0
Fork 0
Code Releases Activity

i.MX fixes for 5.5:

Browse source 
- Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
    so that SPI NOR device can be probed.
  - Fix power button of E60K02 board by removing LDORTC2 regulator.
  - A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
    remove the boot regression caused by 8267ff89b7 ("ARM: imx: Add
    serial number support for i.MX6/7 SoCs").
  - A couple of fixes on LS1028A SoC TMU regarding to calibration data
    and reboot register configuration.
  - Fix a regression seen on imx6ul-evk board by marking always-on for
    the regulator that is shared by many peripherals.
  - Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQEcBAABAgAGBQJd8i+oAAoJEFBXWFqHsHzOSDYH/2clV9RTidg9hYqWV5nuMHry
 16+S4LYyWEkKgSZwheMbX13+f0UEMLZxQ1/c/oTlJGa95GppEzNq0ydmfZ22mScH
 1I1L1t/AfmxiVB6z3HRS0GZk8uIn7CVPe/PBf8tOm+95qEznOOXljykmB2SHLBP3
 KVRSx4OIJ1Nb/IBWmPar7tEkNnLAmI77dTvCZFWbaxep5QTmHX4/dff78eghKmwL
 CyYJeINpsZt6a+sXOMbD7UBUx4zWKv50QDFToCRdGWJ4o+e1vp6FM+s/D82vC+3A
 ZA8cCt9oRxiDAWiwx7gvlpzNVMyLLW3ork7z+a6shtD2Q4BAbStaSNpIXcVKbtI=
 =3SH8
 -----END PGP SIGNATURE-----

Merge tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.5:
 - Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
   so that SPI NOR device can be probed.
 - Fix power button of E60K02 board by removing LDORTC2 regulator.
 - A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
   remove the boot regression caused by 8267ff89b7 ("ARM: imx: Add
   serial number support for i.MX6/7 SoCs").
 - A couple of fixes on LS1028A SoC TMU regarding to calibration data
   and reboot register configuration.
 - Fix a regression seen on imx6ul-evk board by marking always-on for
   the regulator that is shared by many peripherals.
 - Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.

* tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: Fix boot crash if ocotp is not found
  ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
  ARM: dts: imx6ul-evk: Fix peripheral regulator
  arm64: dts: ls1028a: fix reboot node
  arm64: dts: ls1028a: fix typo in TMU calibration data
  ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
  ARM: dts: e60k02: fix power button
  ARM: dts: imx6ul: imx6ul-14x14-evk.dtsi: Fix SPI NOR probing

Link: https://lore.kernel.org/r/20191212122427.GK15858@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit is contained in:
Olof Johansson 2019-12-12 09:38:22 -08:00
parent 9103bb419a 7947e3238b
commit 89f33b984a
5 changed files with 35 additions and 17 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

5
arch/arm/boot/dts/e60k02.dtsi
View file

@ -265,11 +265,6 @@
regulator-name = "LDORTC1";
regulator-boot-on;
};
ldortc2_reg: LDORTC2 {
regulator-name = "LDORTC2";
regulator-boot-on;
};
};
};
};

28
arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
View file

@ -30,14 +30,26 @@
enable-active-high;
};
reg_sensors: regulator-sensors {
reg_peri_3v3: regulator-peri-3v3 {
compatible = "regulator-fixed";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_sensors_reg>;
regulator-name = "sensors-supply";
pinctrl-0 = <&pinctrl_peri_3v3>;
regulator-name = "VPERI_3V3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 2 GPIO_ACTIVE_LOW>;
/*
* If you want to want to make this dynamic please
* check schematics and test all affected peripherals:
*
* - sensors
* - ethernet phy
* - can
* - bluetooth
* - wm8960 audio codec
* - ov5640 camera
*/
regulator-always-on;
};
reg_can_3v3: regulator-can-3v3 {
@ -140,6 +152,7 @@
pinctrl-0 = <&pinctrl_enet1>;
phy-mode = "rmii";
phy-handle = <&ethphy0>;
phy-supply = <&reg_peri_3v3>;
status = "okay";
};
@ -148,6 +161,7 @@
pinctrl-0 = <&pinctrl_enet2>;
phy-mode = "rmii";
phy-handle = <&ethphy1>;
phy-supply = <&reg_peri_3v3>;
status = "okay";
mdio {
@ -193,8 +207,8 @@
magnetometer@e {
compatible = "fsl,mag3110";
reg = <0x0e>;
vdd-supply = <&reg_sensors>;
vddio-supply = <&reg_sensors>;
vdd-supply = <&reg_peri_3v3>;
vddio-supply = <&reg_peri_3v3>;
};
};
@ -227,7 +241,7 @@
flash0: n25q256a@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "micron,n25q256a";
compatible = "micron,n25q256a", "jedec,spi-nor";
spi-max-frequency = <29000000>;
spi-rx-bus-width = <4>;
spi-tx-bus-width = <4>;
@ -462,7 +476,7 @@
>;
};
pinctrl_sensors_reg: sensorsreggrp {
pinctrl_peri_3v3: peri3v3grp {
fsl,pins = <
MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0
>;

1
arch/arm/configs/imx_v6_v7_defconfig
View file

@ -462,6 +462,7 @@ CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_FS=y
# CONFIG_SCHED_DEBUG is not set
CONFIG_PROVE_LOCKING=y
# CONFIG_DEBUG_BUGVERBOSE is not set

8
arch/arm/mach-imx/cpu.c
View file

@ -84,7 +84,7 @@ struct device * __init imx_soc_device_init(void)
const char *ocotp_compat = NULL;
struct soc_device *soc_dev;
struct device_node *root;
struct regmap *ocotp;
struct regmap *ocotp = NULL;
const char *soc_id;
u64 soc_uid = 0;
u32 val;
@ -148,11 +148,11 @@ struct device * __init imx_soc_device_init(void)
soc_id = "i.MX6UL";
break;
case MXC_CPU_IMX6ULL:
ocotp_compat = "fsl,imx6ul-ocotp";
ocotp_compat = "fsl,imx6ull-ocotp";
soc_id = "i.MX6ULL";
break;
case MXC_CPU_IMX6ULZ:
ocotp_compat = "fsl,imx6ul-ocotp";
ocotp_compat = "fsl,imx6ull-ocotp";
soc_id = "i.MX6ULZ";
break;
case MXC_CPU_IMX6SLL:
@ -175,7 +175,9 @@ struct device * __init imx_soc_device_init(void)
ocotp = syscon_regmap_lookup_by_compatible(ocotp_compat);
if (IS_ERR(ocotp))
pr_err("%s: failed to find %s regmap!\n", __func__, ocotp_compat);
}
if (!IS_ERR_OR_NULL(ocotp)) {
regmap_read(ocotp, OCOTP_UID_H, &val);
soc_uid = val;
regmap_read(ocotp, OCOTP_UID_L, &val);

10
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
View file

@ -88,7 +88,7 @@
reboot {
compatible ="syscon-reboot";
regmap = <&dcfg>;
regmap = <&rst>;
offset = <0xb0>;
mask = <0x02>;
};
@ -178,6 +178,12 @@
big-endian;
};
rst: syscon@1e60000 {
compatible = "syscon";
reg = <0x0 0x1e60000 0x0 0x10000>;
little-endian;
};
scfg: syscon@1fc0000 {
compatible = "fsl,ls1028a-scfg", "syscon";
reg = <0x0 0x1fc0000 0x0 0x10000>;
@ -584,7 +590,7 @@
0x00010004 0x0000003d
0x00010005 0x00000045
0x00010006 0x0000004d
0x00010007 0x00000045
0x00010007 0x00000055
0x00010008 0x0000005e
0x00010009 0x00000066
0x0001000a 0x0000006e