diff --git a/Documentation/devicetree/bindings/arm/sprd.txt b/Documentation/devicetree/bindings/arm/sprd.txt
index 31a629dc75b8..3df034b13e28 100644
--- a/Documentation/devicetree/bindings/arm/sprd.txt
+++ b/Documentation/devicetree/bindings/arm/sprd.txt
@@ -1,11 +1,14 @@
 Spreadtrum SoC Platforms Device Tree Bindings
 ----------------------------------------------------
 
-Sharkl64 is a Spreadtrum's SoC Platform which is based
-on ARM 64-bit processor.
-
-SC9836 openphone board with SC9836 SoC based on the
-Sharkl64 Platform shall have the following properties.
-
+SC9836 openphone Board
 Required root node properties:
-        - compatible = "sprd,sc9836-openphone", "sprd,sc9836";
+	- compatible = "sprd,sc9836-openphone", "sprd,sc9836";
+
+SC9860 SoC
+Required root node properties:
+	- compatible = "sprd,sc9860"
+
+SP9860G 3GFHD Board
+Required root node properties:
+	- compatible = "sprd,sp9860g-1h10", "sprd,sc9860";
diff --git a/Documentation/devicetree/bindings/serial/sprd-uart.txt b/Documentation/devicetree/bindings/serial/sprd-uart.txt
index 2aff0f22c9fa..cab40f0f6f49 100644
--- a/Documentation/devicetree/bindings/serial/sprd-uart.txt
+++ b/Documentation/devicetree/bindings/serial/sprd-uart.txt
@@ -1,7 +1,19 @@
 * Spreadtrum serial UART
 
 Required properties:
-- compatible: must be "sprd,sc9836-uart"
+- compatible: must be one of:
+  * "sprd,sc9836-uart"
+  * "sprd,sc9860-uart", "sprd,sc9836-uart"
+
 - reg: offset and length of the register set for the device
 - interrupts: exactly one interrupt specifier
 - clocks: phandles to input clocks.
+
+Example:
+	uart0: serial@0 {
+		compatible = "sprd,sc9860-uart",
+			     "sprd,sc9836-uart";
+		reg = <0x0 0x100>;
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&ext_26m>;
+	};
diff --git a/MAINTAINERS b/MAINTAINERS
index 08360bb0468b..56b1111cc9c1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8418,7 +8418,7 @@ MICROCHIP / ATMEL AT91 / AT32 SERIAL DRIVER
 M:	Richard Genoud <richard.genoud@gmail.com>
 S:	Maintained
 F:	drivers/tty/serial/atmel_serial.c
-F:	include/linux/atmel_serial.h
+F:	drivers/tty/serial/atmel_serial.h
 
 MICROCHIP / ATMEL DMA DRIVER
 M:	Ludovic Desroches <ludovic.desroches@microchip.com>
diff --git a/drivers/tty/Makefile b/drivers/tty/Makefile
index b95bed92da9f..f02becdb3e33 100644
--- a/drivers/tty/Makefile
+++ b/drivers/tty/Makefile
@@ -1,5 +1,6 @@
 obj-$(CONFIG_TTY)		+= tty_io.o n_tty.o tty_ioctl.o tty_ldisc.o \
-				   tty_buffer.o tty_port.o tty_mutex.o tty_ldsem.o
+				   tty_buffer.o tty_port.o tty_mutex.o \
+				   tty_ldsem.o tty_baudrate.o tty_jobctrl.o
 obj-$(CONFIG_LEGACY_PTYS)	+= pty.o
 obj-$(CONFIG_UNIX98_PTYS)	+= pty.o
 obj-$(CONFIG_AUDIT)		+= tty_audit.o
diff --git a/drivers/tty/hvc/hvc_console.c b/drivers/tty/hvc/hvc_console.c
index b19ae36a05ec..a8d399188242 100644
--- a/drivers/tty/hvc/hvc_console.c
+++ b/drivers/tty/hvc/hvc_console.c
@@ -920,17 +920,17 @@ int hvc_remove(struct hvc_struct *hp)
 
 	tty = tty_port_tty_get(&hp->port);
 
+	console_lock();
 	spin_lock_irqsave(&hp->lock, flags);
 	if (hp->index < MAX_NR_HVC_CONSOLES) {
-		console_lock();
 		vtermnos[hp->index] = -1;
 		cons_ops[hp->index] = NULL;
-		console_unlock();
 	}
 
 	/* Don't whack hp->irq because tty_hangup() will need to free the irq. */
 
 	spin_unlock_irqrestore(&hp->lock, flags);
+	console_unlock();
 
 	/*
 	 * We 'put' the instance that was grabbed when the kref instance
diff --git a/drivers/tty/hvc/hvcs.c b/drivers/tty/hvc/hvcs.c
index 7823d6d998cf..99bb875178d7 100644
--- a/drivers/tty/hvc/hvcs.c
+++ b/drivers/tty/hvc/hvcs.c
@@ -1575,7 +1575,7 @@ static int __init hvcs_module_init(void)
 	 */
 	rc = driver_create_file(&(hvcs_vio_driver.driver), &driver_attr_rescan);
 	if (rc)
-		pr_warning("HVCS: Failed to create rescan file (err %d)\n", rc);
+		pr_warn("HVCS: Failed to create rescan file (err %d)\n", rc);
 
 	return 0;
 }
diff --git a/drivers/tty/n_gsm.c b/drivers/tty/n_gsm.c
index 55577cf9b6a4..2667a205a5ab 100644
--- a/drivers/tty/n_gsm.c
+++ b/drivers/tty/n_gsm.c
@@ -89,18 +89,14 @@ module_param(debug, int, 0600);
 /**
  *	struct gsm_mux_net	-	network interface
  *	@struct gsm_dlci* dlci
- *	@struct net_device_stats stats;
  *
  *	Created when net interface is initialized.
  **/
 struct gsm_mux_net {
 	struct kref ref;
 	struct gsm_dlci *dlci;
-	struct net_device_stats stats;
 };
 
-#define STATS(net) (((struct gsm_mux_net *)netdev_priv(net))->stats)
-
 /*
  *	Each block of data we have queued to go out is in the form of
  *	a gsm_msg which holds everything we need in a link layer independent
@@ -2613,10 +2609,6 @@ static int gsm_mux_net_close(struct net_device *net)
 	return 0;
 }
 
-static struct net_device_stats *gsm_mux_net_get_stats(struct net_device *net)
-{
-	return &((struct gsm_mux_net *)netdev_priv(net))->stats;
-}
 static void dlci_net_free(struct gsm_dlci *dlci)
 {
 	if (!dlci->net) {
@@ -2660,8 +2652,8 @@ static int gsm_mux_net_start_xmit(struct sk_buff *skb,
 	muxnet_get(mux_net);
 
 	skb_queue_head(&dlci->skb_list, skb);
-	STATS(net).tx_packets++;
-	STATS(net).tx_bytes += skb->len;
+	net->stats.tx_packets++;
+	net->stats.tx_bytes += skb->len;
 	gsm_dlci_data_kick(dlci);
 	/* And tell the kernel when the last transmit started. */
 	netif_trans_update(net);
@@ -2676,7 +2668,7 @@ static void gsm_mux_net_tx_timeout(struct net_device *net)
 	dev_dbg(&net->dev, "Tx timed out.\n");
 
 	/* Update statistics */
-	STATS(net).tx_errors++;
+	net->stats.tx_errors++;
 }
 
 static void gsm_mux_rx_netchar(struct gsm_dlci *dlci,
@@ -2691,7 +2683,7 @@ static void gsm_mux_rx_netchar(struct gsm_dlci *dlci,
 	skb = dev_alloc_skb(size + NET_IP_ALIGN);
 	if (!skb) {
 		/* We got no receive buffer. */
-		STATS(net).rx_dropped++;
+		net->stats.rx_dropped++;
 		muxnet_put(mux_net);
 		return;
 	}
@@ -2705,8 +2697,8 @@ static void gsm_mux_rx_netchar(struct gsm_dlci *dlci,
 	netif_rx(skb);
 
 	/* update out statistics */
-	STATS(net).rx_packets++;
-	STATS(net).rx_bytes += size;
+	net->stats.rx_packets++;
+	net->stats.rx_bytes += size;
 	muxnet_put(mux_net);
 	return;
 }
@@ -2718,7 +2710,6 @@ static void gsm_mux_net_init(struct net_device *net)
 		.ndo_stop		= gsm_mux_net_close,
 		.ndo_start_xmit		= gsm_mux_net_start_xmit,
 		.ndo_tx_timeout		= gsm_mux_net_tx_timeout,
-		.ndo_get_stats		= gsm_mux_net_get_stats,
 	};
 
 	net->netdev_ops = &gsm_netdev_ops;
diff --git a/drivers/tty/pty.c b/drivers/tty/pty.c
index 66b59a15780d..65799575c666 100644
--- a/drivers/tty/pty.c
+++ b/drivers/tty/pty.c
@@ -216,16 +216,11 @@ static int pty_signal(struct tty_struct *tty, int sig)
 static void pty_flush_buffer(struct tty_struct *tty)
 {
 	struct tty_struct *to = tty->link;
-	struct tty_ldisc *ld;
 
 	if (!to)
 		return;
 
-	ld = tty_ldisc_ref(to);
-	tty_buffer_flush(to, ld);
-	if (ld)
-		tty_ldisc_deref(ld);
-
+	tty_buffer_flush(to, NULL);
 	if (to->packet) {
 		spin_lock_irq(&tty->ctrl_lock);
 		tty->ctrl_status |= TIOCPKT_FLUSHWRITE;
diff --git a/drivers/tty/serdev/core.c b/drivers/tty/serdev/core.c
index 1c4829a56351..433de5ea9b02 100644
--- a/drivers/tty/serdev/core.c
+++ b/drivers/tty/serdev/core.c
@@ -116,17 +116,41 @@ void serdev_device_close(struct serdev_device *serdev)
 }
 EXPORT_SYMBOL_GPL(serdev_device_close);
 
-int serdev_device_write_buf(struct serdev_device *serdev,
-			    const unsigned char *buf, size_t count)
+void serdev_device_write_wakeup(struct serdev_device *serdev)
+{
+	complete(&serdev->write_comp);
+}
+EXPORT_SYMBOL_GPL(serdev_device_write_wakeup);
+
+int serdev_device_write(struct serdev_device *serdev,
+			const unsigned char *buf, size_t count,
+			unsigned long timeout)
 {
 	struct serdev_controller *ctrl = serdev->ctrl;
+	int ret;
 
-	if (!ctrl || !ctrl->ops->write_buf)
+	if (!ctrl || !ctrl->ops->write_buf ||
+	    (timeout && !serdev->ops->write_wakeup))
 		return -EINVAL;
 
-	return ctrl->ops->write_buf(ctrl, buf, count);
+	mutex_lock(&serdev->write_lock);
+	do {
+		reinit_completion(&serdev->write_comp);
+
+		ret = ctrl->ops->write_buf(ctrl, buf, count);
+		if (ret < 0)
+			break;
+
+		buf += ret;
+		count -= ret;
+
+	} while (count &&
+		 (timeout = wait_for_completion_timeout(&serdev->write_comp,
+							timeout)));
+	mutex_unlock(&serdev->write_lock);
+	return ret < 0 ? ret : (count ? -ETIMEDOUT : 0);
 }
-EXPORT_SYMBOL_GPL(serdev_device_write_buf);
+EXPORT_SYMBOL_GPL(serdev_device_write);
 
 void serdev_device_write_flush(struct serdev_device *serdev)
 {
@@ -262,6 +286,8 @@ struct serdev_device *serdev_device_alloc(struct serdev_controller *ctrl)
 	serdev->dev.parent = &ctrl->dev;
 	serdev->dev.bus = &serdev_bus_type;
 	serdev->dev.type = &serdev_device_type;
+	init_completion(&serdev->write_comp);
+	mutex_init(&serdev->write_lock);
 	return serdev;
 }
 EXPORT_SYMBOL_GPL(serdev_device_alloc);
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 76e03a7de9cc..48a07e2f617f 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -218,7 +218,7 @@ static int serial_link_irq_chain(struct uart_8250_port *up)
 		spin_unlock_irq(&i->lock);
 		irq_flags |= up->port.irqflags;
 		ret = request_irq(up->port.irq, serial8250_interrupt,
-				  irq_flags, "serial", i);
+				  irq_flags, up->port.name, i);
 		if (ret < 0)
 			serial_do_unlink(i, up);
 	}
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index e65808c482f1..787b1160d3a5 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -530,12 +530,11 @@ static int dw8250_probe(struct platform_device *pdev)
 	}
 
 	data->rst = devm_reset_control_get_optional(dev, NULL);
-	if (IS_ERR(data->rst) && PTR_ERR(data->rst) == -EPROBE_DEFER) {
-		err = -EPROBE_DEFER;
+	if (IS_ERR(data->rst)) {
+		err = PTR_ERR(data->rst);
 		goto err_pclk;
 	}
-	if (!IS_ERR(data->rst))
-		reset_control_deassert(data->rst);
+	reset_control_deassert(data->rst);
 
 	dw8250_quirks(p, data);
 
@@ -567,8 +566,7 @@ static int dw8250_probe(struct platform_device *pdev)
 	return 0;
 
 err_reset:
-	if (!IS_ERR(data->rst))
-		reset_control_assert(data->rst);
+	reset_control_assert(data->rst);
 
 err_pclk:
 	if (!IS_ERR(data->pclk))
@@ -589,8 +587,7 @@ static int dw8250_remove(struct platform_device *pdev)
 
 	serial8250_unregister_port(data->line);
 
-	if (!IS_ERR(data->rst))
-		reset_control_assert(data->rst);
+	reset_control_assert(data->rst);
 
 	if (!IS_ERR(data->pclk))
 		clk_disable_unprepare(data->pclk);
diff --git a/drivers/tty/serial/8250/8250_early.c b/drivers/tty/serial/8250/8250_early.c
index 85a12f032402..82fc48eca1df 100644
--- a/drivers/tty/serial/8250/8250_early.c
+++ b/drivers/tty/serial/8250/8250_early.c
@@ -39,6 +39,7 @@
 
 static unsigned int __init serial8250_early_in(struct uart_port *port, int offset)
 {
+	int reg_offset = offset;
 	offset <<= port->regshift;
 
 	switch (port->iotype) {
@@ -52,6 +53,8 @@ static unsigned int __init serial8250_early_in(struct uart_port *port, int offse
 		return ioread32be(port->membase + offset);
 	case UPIO_PORT:
 		return inb(port->iobase + offset);
+	case UPIO_AU:
+		return port->serial_in(port, reg_offset);
 	default:
 		return 0;
 	}
@@ -59,6 +62,7 @@ static unsigned int __init serial8250_early_in(struct uart_port *port, int offse
 
 static void __init serial8250_early_out(struct uart_port *port, int offset, int value)
 {
+	int reg_offset = offset;
 	offset <<= port->regshift;
 
 	switch (port->iotype) {
@@ -77,6 +81,9 @@ static void __init serial8250_early_out(struct uart_port *port, int offset, int
 	case UPIO_PORT:
 		outb(value, port->iobase + offset);
 		break;
+	case UPIO_AU:
+		port->serial_out(port, reg_offset, value);
+		break;
 	}
 }
 
@@ -172,3 +179,20 @@ OF_EARLYCON_DECLARE(omap8250, "ti,omap3-uart", early_omap8250_setup);
 OF_EARLYCON_DECLARE(omap8250, "ti,omap4-uart", early_omap8250_setup);
 
 #endif
+
+#ifdef CONFIG_SERIAL_8250_RT288X
+
+unsigned int au_serial_in(struct uart_port *p, int offset);
+void au_serial_out(struct uart_port *p, int offset, int value);
+
+static int __init early_au_setup(struct earlycon_device *dev, const char *opt)
+{
+	dev->port.serial_in = au_serial_in;
+	dev->port.serial_out = au_serial_out;
+	dev->port.iotype = UPIO_AU;
+	dev->con->write = early_serial8250_write;
+	return 0;
+}
+OF_EARLYCON_DECLARE(palmchip, "ralink,rt2880-uart", early_au_setup);
+
+#endif
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index b89c4ffc0486..1270ff163f63 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -483,5 +483,5 @@ static struct pci_driver exar_pci_driver = {
 module_pci_driver(exar_pci_driver);
 
 MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("Exar Serial Dricer");
+MODULE_DESCRIPTION("Exar Serial Driver");
 MODULE_AUTHOR("Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>");
diff --git a/drivers/tty/serial/8250/8250_fintek.c b/drivers/tty/serial/8250/8250_fintek.c
index b67e7a544935..e500f7dd2470 100644
--- a/drivers/tty/serial/8250/8250_fintek.c
+++ b/drivers/tty/serial/8250/8250_fintek.c
@@ -61,6 +61,12 @@
  * The IRQ setting mode of F81866 is not the same with F81216 series.
  *	Level/Low: IRQ_MODE0:0, IRQ_MODE1:0
  *	Edge/High: IRQ_MODE0:1, IRQ_MODE1:0
+ *
+ * Clock speeds for UART (register F2h)
+ * 00: 1.8432MHz.
+ * 01: 18.432MHz.
+ * 10: 24MHz.
+ * 11: 14.769MHz.
  */
 #define F81866_IRQ_MODE		0xf0
 #define F81866_IRQ_SHARE	BIT(0)
@@ -72,6 +78,13 @@
 #define F81866_LDN_LOW		0x10
 #define F81866_LDN_HIGH		0x16
 
+#define F81866_UART_CLK 0xF2
+#define F81866_UART_CLK_MASK (BIT(1) | BIT(0))
+#define F81866_UART_CLK_1_8432MHZ 0
+#define F81866_UART_CLK_14_769MHZ (BIT(1) | BIT(0))
+#define F81866_UART_CLK_18_432MHZ BIT(0)
+#define F81866_UART_CLK_24MHZ BIT(1)
+
 struct fintek_8250 {
 	u16 pid;
 	u16 base_port;
@@ -256,8 +269,26 @@ static void fintek_8250_set_max_fifo(struct fintek_8250 *pdata)
 	}
 }
 
-static int probe_setup_port(struct fintek_8250 *pdata, u16 io_address,
-			  unsigned int irq)
+static void fintek_8250_goto_highspeed(struct uart_8250_port *uart,
+			      struct fintek_8250 *pdata)
+{
+	sio_write_reg(pdata, LDN, pdata->index);
+
+	switch (pdata->pid) {
+	case CHIP_ID_F81866: /* set uart clock for high speed serial mode */
+		sio_write_mask_reg(pdata, F81866_UART_CLK,
+			F81866_UART_CLK_MASK,
+			F81866_UART_CLK_14_769MHZ);
+
+			uart->port.uartclk = 921600 * 16;
+		break;
+	default: /* leave clock speed untouched */
+		break;
+	}
+}
+
+static int probe_setup_port(struct fintek_8250 *pdata,
+					struct uart_8250_port *uart)
 {
 	static const u16 addr[] = {0x4e, 0x2e};
 	static const u8 keys[] = {0x77, 0xa0, 0x87, 0x67};
@@ -284,18 +315,20 @@ static int probe_setup_port(struct fintek_8250 *pdata, u16 io_address,
 				sio_write_reg(pdata, LDN, k);
 				aux = sio_read_reg(pdata, IO_ADDR1);
 				aux |= sio_read_reg(pdata, IO_ADDR2) << 8;
-				if (aux != io_address)
+				if (aux != uart->port.iobase)
 					continue;
 
 				pdata->index = k;
 
-				irq_data = irq_get_irq_data(irq);
+				irq_data = irq_get_irq_data(uart->port.irq);
 				if (irq_data)
 					level_mode =
 						irqd_is_level_type(irq_data);
 
 				fintek_8250_set_irq_mode(pdata, level_mode);
 				fintek_8250_set_max_fifo(pdata);
+				fintek_8250_goto_highspeed(uart, pdata);
+
 				fintek_8250_exit_key(addr[i]);
 
 				return 0;
@@ -330,7 +363,7 @@ int fintek_8250_probe(struct uart_8250_port *uart)
 	struct fintek_8250 *pdata;
 	struct fintek_8250 probe_data;
 
-	if (probe_setup_port(&probe_data, uart->port.iobase, uart->port.irq))
+	if (probe_setup_port(&probe_data, uart))
 		return -ENODEV;
 
 	pdata = devm_kzalloc(uart->port.dev, sizeof(*pdata), GFP_KERNEL);
diff --git a/drivers/tty/serial/8250/8250_lpss.c b/drivers/tty/serial/8250/8250_lpss.c
index f3ea90f0e411..7dddd7e6a01c 100644
--- a/drivers/tty/serial/8250/8250_lpss.c
+++ b/drivers/tty/serial/8250/8250_lpss.c
@@ -183,7 +183,6 @@ static void qrk_serial_setup_dma(struct lpss8250 *lpss, struct uart_port *port)
 	if (ret)
 		return;
 
-	pci_set_master(pdev);
 	pci_try_set_mwi(pdev);
 
 	/* Special DMA address for UART */
@@ -216,6 +215,8 @@ static int qrk_serial_setup(struct lpss8250 *lpss, struct uart_port *port)
 	struct pci_dev *pdev = to_pci_dev(port->dev);
 	int ret;
 
+	pci_set_master(pdev);
+
 	ret = pci_alloc_irq_vectors(pdev, 1, 1, PCI_IRQ_ALL_TYPES);
 	if (ret < 0)
 		return ret;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 6119516ef5fc..09a65a3ec7f7 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -328,7 +328,7 @@ static const s8 au_io_out_map[8] = {
 	-1,	/* UART_SCR (unmapped) */
 };
 
-static unsigned int au_serial_in(struct uart_port *p, int offset)
+unsigned int au_serial_in(struct uart_port *p, int offset)
 {
 	if (offset >= ARRAY_SIZE(au_io_in_map))
 		return UINT_MAX;
@@ -338,7 +338,7 @@ static unsigned int au_serial_in(struct uart_port *p, int offset)
 	return __raw_readl(p->membase + (offset << p->regshift));
 }
 
-static void au_serial_out(struct uart_port *p, int offset, int value)
+void au_serial_out(struct uart_port *p, int offset, int value)
 {
 	if (offset >= ARRAY_SIZE(au_io_out_map))
 		return;
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 6117ac8da48f..5c8850f7a2a0 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -630,6 +630,15 @@ config SERIAL_UARTLITE_CONSOLE
 	  console (the system console is the device which receives all kernel
 	  messages and warnings and which allows logins in single user mode).
 
+config SERIAL_UARTLITE_NR_UARTS
+	int "Maximum number of uartlite serial ports"
+	depends on SERIAL_UARTLITE
+	range 1 256
+	default 1
+	help
+	  Set this to the number of uartlites in your system, or the number
+	  you think you might implement.
+
 config SERIAL_SUNCORE
 	bool
 	depends on SPARC
@@ -1343,6 +1352,7 @@ config SERIAL_ALTERA_JTAGUART_CONSOLE
 	bool "Altera JTAG UART console support"
 	depends on SERIAL_ALTERA_JTAGUART=y
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 	help
 	  Enable a Altera JTAG UART port to be the system console.
 
@@ -1382,6 +1392,7 @@ config SERIAL_ALTERA_UART_CONSOLE
 	bool "Altera UART console support"
 	depends on SERIAL_ALTERA_UART=y
 	select SERIAL_CORE_CONSOLE
+	select SERIAL_EARLYCON
 	help
 	  Enable a Altera UART port to be the system console.
 
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 2d6288bc4554..53c03e005132 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -3,7 +3,6 @@
 #
 
 obj-$(CONFIG_SERIAL_CORE) += serial_core.o
-obj-$(CONFIG_SERIAL_21285) += 21285.o
 
 obj-$(CONFIG_SERIAL_EARLYCON) += earlycon.o
 obj-$(CONFIG_SERIAL_EARLYCON_ARM_SEMIHOST) += earlycon-arm-semihost.o
@@ -17,6 +16,8 @@ obj-$(CONFIG_SERIAL_SUNZILOG) += sunzilog.o
 obj-$(CONFIG_SERIAL_SUNSU) += sunsu.o
 obj-$(CONFIG_SERIAL_SUNSAB) += sunsab.o
 
+obj-$(CONFIG_SERIAL_21285) += 21285.o
+
 # Now bring in any enabled 8250/16450/16550 type drivers.
 obj-$(CONFIG_SERIAL_8250) += 8250/
 
diff --git a/drivers/tty/serial/altera_jtaguart.c b/drivers/tty/serial/altera_jtaguart.c
index e409d7dac7ab..18e3f8342b85 100644
--- a/drivers/tty/serial/altera_jtaguart.c
+++ b/drivers/tty/serial/altera_jtaguart.c
@@ -383,6 +383,26 @@ console_initcall(altera_jtaguart_console_init);
 
 #define	ALTERA_JTAGUART_CONSOLE	(&altera_jtaguart_console)
 
+static void altera_jtaguart_earlycon_write(struct console *co, const char *s,
+					   unsigned int count)
+{
+	struct earlycon_device *dev = co->data;
+
+	uart_console_write(&dev->port, s, count, altera_jtaguart_console_putc);
+}
+
+static int __init altera_jtaguart_earlycon_setup(struct earlycon_device *dev,
+						 const char *options)
+{
+	if (!dev->port.membase)
+		return -ENODEV;
+
+	dev->con->write = altera_jtaguart_earlycon_write;
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(juart, "altr,juart-1.0", altera_jtaguart_earlycon_setup);
+
 #else
 
 #define	ALTERA_JTAGUART_CONSOLE	NULL
diff --git a/drivers/tty/serial/altera_uart.c b/drivers/tty/serial/altera_uart.c
index 820a74208696..46d3438a0d27 100644
--- a/drivers/tty/serial/altera_uart.c
+++ b/drivers/tty/serial/altera_uart.c
@@ -489,6 +489,38 @@ console_initcall(altera_uart_console_init);
 
 #define	ALTERA_UART_CONSOLE	(&altera_uart_console)
 
+static void altera_uart_earlycon_write(struct console *co, const char *s,
+				       unsigned int count)
+{
+	struct earlycon_device *dev = co->data;
+
+	uart_console_write(&dev->port, s, count, altera_uart_console_putc);
+}
+
+static int __init altera_uart_earlycon_setup(struct earlycon_device *dev,
+					     const char *options)
+{
+	struct uart_port *port = &dev->port;
+
+	if (!port->membase)
+		return -ENODEV;
+
+	/* Enable RX interrupts now */
+	writel(ALTERA_UART_CONTROL_RRDY_MSK,
+	       port->membase + ALTERA_UART_CONTROL_REG);
+
+	if (dev->baud) {
+		unsigned int baudclk = port->uartclk / dev->baud;
+
+		writel(baudclk, port->membase + ALTERA_UART_DIVISOR_REG);
+	}
+
+	dev->con->write = altera_uart_earlycon_write;
+	return 0;
+}
+
+OF_EARLYCON_DECLARE(uart, "altr,uart-1.0", altera_uart_earlycon_setup);
+
 #else
 
 #define	ALTERA_UART_CONSOLE	NULL
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index b0a377725d63..8a857bb34fbb 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1327,14 +1327,15 @@ static void pl011_stop_tx(struct uart_port *port)
 	pl011_dma_tx_stop(uap);
 }
 
-static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
+static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq);
 
 /* Start TX with programmed I/O only (no DMA) */
 static void pl011_start_tx_pio(struct uart_amba_port *uap)
 {
-	uap->im |= UART011_TXIM;
-	pl011_write(uap->im, uap, REG_IMSC);
-	pl011_tx_chars(uap, false);
+	if (pl011_tx_chars(uap, false)) {
+		uap->im |= UART011_TXIM;
+		pl011_write(uap->im, uap, REG_IMSC);
+	}
 }
 
 static void pl011_start_tx(struct uart_port *port)
@@ -1414,25 +1415,26 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
 	return true;
 }
 
-static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
+/* Returns true if tx interrupts have to be (kept) enabled  */
+static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 {
 	struct circ_buf *xmit = &uap->port.state->xmit;
 	int count = uap->fifosize >> 1;
 
 	if (uap->port.x_char) {
 		if (!pl011_tx_char(uap, uap->port.x_char, from_irq))
-			return;
+			return true;
 		uap->port.x_char = 0;
 		--count;
 	}
 	if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
 		pl011_stop_tx(&uap->port);
-		return;
+		return false;
 	}
 
 	/* If we are using DMA mode, try to send some characters. */
 	if (pl011_dma_tx_irq(uap))
-		return;
+		return true;
 
 	do {
 		if (likely(from_irq) && count-- == 0)
@@ -1447,8 +1449,11 @@ static void pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(&uap->port);
 
-	if (uart_circ_empty(xmit))
+	if (uart_circ_empty(xmit)) {
 		pl011_stop_tx(&uap->port);
+		return false;
+	}
+	return true;
 }
 
 static void pl011_modem_status(struct uart_amba_port *uap)
@@ -2470,19 +2475,34 @@ static int __init pl011_early_console_setup(struct earlycon_device *device,
 	if (!device->port.membase)
 		return -ENODEV;
 
-	/* On QDF2400 SOCs affected by Erratum 44, the "qdf2400_e44" must
-	 * also be specified, e.g. "earlycon=pl011,<address>,qdf2400_e44".
-	 */
-	if (!strcmp(device->options, "qdf2400_e44"))
-		device->con->write = qdf2400_e44_early_write;
-	else
-		device->con->write = pl011_early_write;
+	device->con->write = pl011_early_write;
 
 	return 0;
 }
 OF_EARLYCON_DECLARE(pl011, "arm,pl011", pl011_early_console_setup);
 OF_EARLYCON_DECLARE(pl011, "arm,sbsa-uart", pl011_early_console_setup);
-EARLYCON_DECLARE(qdf2400_e44, pl011_early_console_setup);
+
+/*
+ * On Qualcomm Datacenter Technologies QDF2400 SOCs affected by
+ * Erratum 44, traditional earlycon can be enabled by specifying
+ * "earlycon=qdf2400_e44,<address>".  Any options are ignored.
+ *
+ * Alternatively, you can just specify "earlycon", and the early console
+ * will be enabled with the information from the SPCR table.  In this
+ * case, the SPCR code will detect the need for the E44 work-around,
+ * and set the console name to "qdf2400_e44".
+ */
+static int __init
+qdf2400_e44_early_console_setup(struct earlycon_device *device,
+				const char *opt)
+{
+	if (!device->port.membase)
+		return -ENODEV;
+
+	device->con->write = qdf2400_e44_early_write;
+	return 0;
+}
+EARLYCON_DECLARE(qdf2400_e44, qdf2400_e44_early_console_setup);
 
 #else
 #define AMBA_CONSOLE	NULL
diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
index 1f50a83ef958..c355ac9abafc 100644
--- a/drivers/tty/serial/atmel_serial.c
+++ b/drivers/tty/serial/atmel_serial.c
@@ -38,7 +38,6 @@
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/atmel_pdc.h>
-#include <linux/atmel_serial.h>
 #include <linux/uaccess.h>
 #include <linux/platform_data/atmel.h>
 #include <linux/timer.h>
@@ -71,6 +70,7 @@
 #include <linux/serial_core.h>
 
 #include "serial_mctrl_gpio.h"
+#include "atmel_serial.h"
 
 static void atmel_start_rx(struct uart_port *port);
 static void atmel_stop_rx(struct uart_port *port);
@@ -119,8 +119,9 @@ struct atmel_uart_char {
 /*
  * at91: 6 USARTs and one DBGU port (SAM9260)
  * avr32: 4
+ * samx7: 3 USARTs and 5 UARTs
  */
-#define ATMEL_MAX_UART		7
+#define ATMEL_MAX_UART		8
 
 /*
  * We wrap our port structure around the generic uart_port.
@@ -175,6 +176,7 @@ struct atmel_uart_port {
 	unsigned int		pending_status;
 	spinlock_t		lock_suspended;
 
+#ifdef CONFIG_PM
 	struct {
 		u32		cr;
 		u32		mr;
@@ -185,6 +187,7 @@ struct atmel_uart_port {
 		u32		fmr;
 		u32		fimr;
 	} cache;
+#endif
 
 	int (*prepare_rx)(struct uart_port *port);
 	int (*prepare_tx)(struct uart_port *port);
diff --git a/include/linux/atmel_serial.h b/drivers/tty/serial/atmel_serial.h
similarity index 100%
rename from include/linux/atmel_serial.h
rename to drivers/tty/serial/atmel_serial.h
diff --git a/drivers/tty/serial/fsl_lpuart.c b/drivers/tty/serial/fsl_lpuart.c
index f02934ffb329..15df1ba78095 100644
--- a/drivers/tty/serial/fsl_lpuart.c
+++ b/drivers/tty/serial/fsl_lpuart.c
@@ -1705,6 +1705,13 @@ lpuart_console_write(struct console *co, const char *s, unsigned int count)
 {
 	struct lpuart_port *sport = lpuart_ports[co->index];
 	unsigned char  old_cr2, cr2;
+	unsigned long flags;
+	int locked = 1;
+
+	if (sport->port.sysrq || oops_in_progress)
+		locked = spin_trylock_irqsave(&sport->port.lock, flags);
+	else
+		spin_lock_irqsave(&sport->port.lock, flags);
 
 	/* first save CR2 and then disable interrupts */
 	cr2 = old_cr2 = readb(sport->port.membase + UARTCR2);
@@ -1719,6 +1726,9 @@ lpuart_console_write(struct console *co, const char *s, unsigned int count)
 		barrier();
 
 	writeb(old_cr2, sport->port.membase + UARTCR2);
+
+	if (locked)
+		spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
 static void
@@ -1726,6 +1736,13 @@ lpuart32_console_write(struct console *co, const char *s, unsigned int count)
 {
 	struct lpuart_port *sport = lpuart_ports[co->index];
 	unsigned long  old_cr, cr;
+	unsigned long flags;
+	int locked = 1;
+
+	if (sport->port.sysrq || oops_in_progress)
+		locked = spin_trylock_irqsave(&sport->port.lock, flags);
+	else
+		spin_lock_irqsave(&sport->port.lock, flags);
 
 	/* first save CR2 and then disable interrupts */
 	cr = old_cr = lpuart32_read(sport->port.membase + UARTCTRL);
@@ -1740,6 +1757,9 @@ lpuart32_console_write(struct console *co, const char *s, unsigned int count)
 		barrier();
 
 	lpuart32_write(old_cr, sport->port.membase + UARTCTRL);
+
+	if (locked)
+		spin_unlock_irqrestore(&sport->port.lock, flags);
 }
 
 /*
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index e3e152cbc75e..33509b4beaec 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -719,6 +719,27 @@ out:
 	return IRQ_HANDLED;
 }
 
+static void imx_disable_rx_int(struct imx_port *sport)
+{
+	unsigned long temp;
+
+	sport->dma_is_rxing = 1;
+
+	/* disable the receiver ready and aging timer interrupts */
+	temp = readl(sport->port.membase + UCR1);
+	temp &= ~(UCR1_RRDYEN);
+	writel(temp, sport->port.membase + UCR1);
+
+	temp = readl(sport->port.membase + UCR2);
+	temp &= ~(UCR2_ATEN);
+	writel(temp, sport->port.membase + UCR2);
+
+	/* disable the rx errors interrupts */
+	temp = readl(sport->port.membase + UCR4);
+	temp &= ~UCR4_OREN;
+	writel(temp, sport->port.membase + UCR4);
+}
+
 static void clear_rx_errors(struct imx_port *sport);
 static int start_rx_dma(struct imx_port *sport);
 /*
@@ -734,21 +755,8 @@ static void imx_dma_rxint(struct imx_port *sport)
 
 	temp = readl(sport->port.membase + USR2);
 	if ((temp & USR2_RDR) && !sport->dma_is_rxing) {
-		sport->dma_is_rxing = 1;
 
-		/* disable the receiver ready and aging timer interrupts */
-		temp = readl(sport->port.membase + UCR1);
-		temp &= ~(UCR1_RRDYEN);
-		writel(temp, sport->port.membase + UCR1);
-
-		temp = readl(sport->port.membase + UCR2);
-		temp &= ~(UCR2_ATEN);
-		writel(temp, sport->port.membase + UCR2);
-
-		/* disable the rx errors interrupts */
-		temp = readl(sport->port.membase + UCR4);
-		temp &= ~UCR4_OREN;
-		writel(temp, sport->port.membase + UCR4);
+		imx_disable_rx_int(sport);
 
 		/* tell the DMA to receive the data. */
 		start_rx_dma(sport);
@@ -1317,19 +1325,10 @@ static int imx_startup(struct uart_port *port)
 	if (!is_imx1_uart(sport)) {
 		temp = readl(sport->port.membase + UCR3);
 
-		/*
-		 * The effect of RI and DCD differs depending on the UFCR_DCEDTE
-		 * bit. In DCE mode they control the outputs, in DTE mode they
-		 * enable the respective irqs. At least the DCD irq cannot be
-		 * cleared on i.MX25 at least, so it's not usable and must be
-		 * disabled. I don't have test hardware to check if RI has the
-		 * same problem but I consider this likely so it's disabled for
-		 * now, too.
-		 */
-		temp |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP |
-			UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
+		temp |= UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
 
 		if (sport->dte_mode)
+			/* disable broken interrupts */
 			temp &= ~(UCR3_RI | UCR3_DCD);
 
 		writel(temp, sport->port.membase + UCR3);
@@ -1339,6 +1338,33 @@ static int imx_startup(struct uart_port *port)
 	 * Enable modem status interrupts
 	 */
 	imx_enable_ms(&sport->port);
+
+	/*
+	 * If the serial port is opened for reading start RX DMA immediately
+	 * instead of waiting for RX FIFO interrupts. In our iMX53 the average
+	 * delay for the first reception dropped from approximately 35000
+	 * microseconds to 1000 microseconds.
+	 */
+	if (sport->dma_is_enabled) {
+		struct tty_struct *tty = sport->port.state->port.tty;
+		struct tty_file_private *file_priv;
+		int readcnt = 0;
+
+		spin_lock(&tty->files_lock);
+
+		if (!list_empty(&tty->tty_files))
+			list_for_each_entry(file_priv, &tty->tty_files, list)
+				if (!(file_priv->file->f_flags & O_WRONLY))
+					readcnt++;
+
+		spin_unlock(&tty->files_lock);
+
+		if (readcnt > 0) {
+			imx_disable_rx_int(sport);
+			start_rx_dma(sport);
+		}
+	}
+
 	spin_unlock_irqrestore(&sport->port.lock, flags);
 
 	return 0;
@@ -1584,8 +1610,6 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	ufcr = readl(sport->port.membase + UFCR);
 	ufcr = (ufcr & (~UFCR_RFDIV)) | UFCR_RFDIV_REG(div);
-	if (sport->dte_mode)
-		ufcr |= UFCR_DCEDTE;
 	writel(ufcr, sport->port.membase + UFCR);
 
 	writel(num, sport->port.membase + UBIR);
@@ -2153,6 +2177,27 @@ static int serial_imx_probe(struct platform_device *pdev)
 		 UCR1_TXMPTYEN | UCR1_RTSDEN);
 	writel_relaxed(reg, sport->port.membase + UCR1);
 
+	if (!is_imx1_uart(sport) && sport->dte_mode) {
+		/*
+		 * The DCEDTE bit changes the direction of DSR, DCD, DTR and RI
+		 * and influences if UCR3_RI and UCR3_DCD changes the level of RI
+		 * and DCD (when they are outputs) or enables the respective
+		 * irqs. So set this bit early, i.e. before requesting irqs.
+		 */
+		writel(UFCR_DCEDTE, sport->port.membase + UFCR);
+
+		/*
+		 * Disable UCR3_RI and UCR3_DCD irqs. They are also not
+		 * enabled later because they cannot be cleared
+		 * (confirmed on i.MX25) which makes them unusable.
+		 */
+		writel(IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP | UCR3_DSR,
+		       sport->port.membase + UCR3);
+
+	} else {
+		writel(0, sport->port.membase + UFCR);
+	}
+
 	clk_disable_unprepare(sport->clk_ipg);
 
 	/*
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index a4734649a0f0..1ea05ac57aa7 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1770,7 +1770,8 @@ static int serial_omap_probe(struct platform_device *pdev)
 	return 0;
 
 err_add_port:
-	pm_runtime_put(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	pm_runtime_put_sync(&pdev->dev);
 	pm_runtime_disable(&pdev->dev);
 	pm_qos_remove_request(&up->pm_qos_request);
 	device_init_wakeup(up->dev, false);
@@ -1783,9 +1784,13 @@ static int serial_omap_remove(struct platform_device *dev)
 {
 	struct uart_omap_port *up = platform_get_drvdata(dev);
 
+	pm_runtime_get_sync(up->dev);
+
+	uart_remove_one_port(&serial_omap_reg, &up->port);
+
+	pm_runtime_dont_use_autosuspend(up->dev);
 	pm_runtime_put_sync(up->dev);
 	pm_runtime_disable(up->dev);
-	uart_remove_one_port(&serial_omap_reg, &up->port);
 	pm_qos_remove_request(&up->pm_qos_request);
 	device_init_wakeup(&dev->dev, false);
 
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index 7a17aedbf902..8aca18c4cdea 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -859,7 +859,7 @@ static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state)
 static int s3c24xx_serial_request_dma(struct s3c24xx_uart_port *p)
 {
 	struct s3c24xx_uart_dma	*dma = p->dma;
-	unsigned long flags;
+	int ret;
 
 	/* Default slave configuration parameters */
 	dma->rx_conf.direction		= DMA_DEV_TO_MEM;
@@ -884,8 +884,8 @@ static int s3c24xx_serial_request_dma(struct s3c24xx_uart_port *p)
 
 	dma->tx_chan = dma_request_chan(p->port.dev, "tx");
 	if (IS_ERR(dma->tx_chan)) {
-		dma_release_channel(dma->rx_chan);
-		return PTR_ERR(dma->tx_chan);
+		ret = PTR_ERR(dma->tx_chan);
+		goto err_release_rx;
 	}
 
 	dmaengine_slave_config(dma->tx_chan, &dma->tx_conf);
@@ -894,26 +894,38 @@ static int s3c24xx_serial_request_dma(struct s3c24xx_uart_port *p)
 	dma->rx_size = PAGE_SIZE;
 
 	dma->rx_buf = kmalloc(dma->rx_size, GFP_KERNEL);
-
 	if (!dma->rx_buf) {
-		dma_release_channel(dma->rx_chan);
-		dma_release_channel(dma->tx_chan);
-		return -ENOMEM;
+		ret = -ENOMEM;
+		goto err_release_tx;
 	}
 
-	dma->rx_addr = dma_map_single(dma->rx_chan->device->dev, dma->rx_buf,
+	dma->rx_addr = dma_map_single(p->port.dev, dma->rx_buf,
 				dma->rx_size, DMA_FROM_DEVICE);
-
-	spin_lock_irqsave(&p->port.lock, flags);
+	if (dma_mapping_error(p->port.dev, dma->rx_addr)) {
+		ret = -EIO;
+		goto err_free_rx;
+	}
 
 	/* TX buffer */
-	dma->tx_addr = dma_map_single(dma->tx_chan->device->dev,
-				p->port.state->xmit.buf,
+	dma->tx_addr = dma_map_single(p->port.dev, p->port.state->xmit.buf,
 				UART_XMIT_SIZE, DMA_TO_DEVICE);
-
-	spin_unlock_irqrestore(&p->port.lock, flags);
+	if (dma_mapping_error(p->port.dev, dma->tx_addr)) {
+		ret = -EIO;
+		goto err_unmap_rx;
+	}
 
 	return 0;
+
+err_unmap_rx:
+	dma_unmap_single(p->port.dev, dma->rx_addr, dma->rx_size,
+			 DMA_FROM_DEVICE);
+err_free_rx:
+	kfree(dma->rx_buf);
+err_release_tx:
+	dma_release_channel(dma->tx_chan);
+err_release_rx:
+	dma_release_channel(dma->rx_chan);
+	return ret;
 }
 
 static void s3c24xx_serial_release_dma(struct s3c24xx_uart_port *p)
@@ -922,7 +934,7 @@ static void s3c24xx_serial_release_dma(struct s3c24xx_uart_port *p)
 
 	if (dma->rx_chan) {
 		dmaengine_terminate_all(dma->rx_chan);
-		dma_unmap_single(dma->rx_chan->device->dev, dma->rx_addr,
+		dma_unmap_single(p->port.dev, dma->rx_addr,
 				dma->rx_size, DMA_FROM_DEVICE);
 		kfree(dma->rx_buf);
 		dma_release_channel(dma->rx_chan);
@@ -931,7 +943,7 @@ static void s3c24xx_serial_release_dma(struct s3c24xx_uart_port *p)
 
 	if (dma->tx_chan) {
 		dmaengine_terminate_all(dma->tx_chan);
-		dma_unmap_single(dma->tx_chan->device->dev, dma->tx_addr,
+		dma_unmap_single(p->port.dev, dma->tx_addr,
 				UART_XMIT_SIZE, DMA_TO_DEVICE);
 		dma_release_channel(dma->tx_chan);
 		dma->tx_chan = NULL;
diff --git a/drivers/tty/serial/sb1250-duart.c b/drivers/tty/serial/sb1250-duart.c
index 771f361c47ea..041625cc24bb 100644
--- a/drivers/tty/serial/sb1250-duart.c
+++ b/drivers/tty/serial/sb1250-duart.c
@@ -41,7 +41,7 @@
 #include <linux/tty_flip.h>
 #include <linux/types.h>
 
-#include <linux/atomic.h>
+#include <linux/refcount.h>
 #include <asm/io.h>
 #include <asm/war.h>
 
@@ -103,7 +103,7 @@ struct sbd_port {
 struct sbd_duart {
 	struct sbd_port		sport[2];
 	unsigned long		mapctrl;
-	atomic_t		map_guard;
+	refcount_t		map_guard;
 };
 
 #define to_sport(uport) container_of(uport, struct sbd_port, port)
@@ -654,15 +654,13 @@ static void sbd_release_port(struct uart_port *uport)
 {
 	struct sbd_port *sport = to_sport(uport);
 	struct sbd_duart *duart = sport->duart;
-	int map_guard;
 
 	iounmap(sport->memctrl);
 	sport->memctrl = NULL;
 	iounmap(uport->membase);
 	uport->membase = NULL;
 
-	map_guard = atomic_add_return(-1, &duart->map_guard);
-	if (!map_guard)
+	if(refcount_dec_and_test(&duart->map_guard))
 		release_mem_region(duart->mapctrl, DUART_CHANREG_SPACING);
 	release_mem_region(uport->mapbase, DUART_CHANREG_SPACING);
 }
@@ -698,7 +696,6 @@ static int sbd_request_port(struct uart_port *uport)
 {
 	const char *err = KERN_ERR "sbd: Unable to reserve MMIO resource\n";
 	struct sbd_duart *duart = to_sport(uport)->duart;
-	int map_guard;
 	int ret = 0;
 
 	if (!request_mem_region(uport->mapbase, DUART_CHANREG_SPACING,
@@ -706,11 +703,11 @@ static int sbd_request_port(struct uart_port *uport)
 		printk(err);
 		return -EBUSY;
 	}
-	map_guard = atomic_add_return(1, &duart->map_guard);
-	if (map_guard == 1) {
+	refcount_inc(&duart->map_guard);
+	if (refcount_read(&duart->map_guard) == 1) {
 		if (!request_mem_region(duart->mapctrl, DUART_CHANREG_SPACING,
 					"sb1250-duart")) {
-			atomic_add(-1, &duart->map_guard);
+			refcount_dec(&duart->map_guard);
 			printk(err);
 			ret = -EBUSY;
 		}
@@ -718,8 +715,7 @@ static int sbd_request_port(struct uart_port *uport)
 	if (!ret) {
 		ret = sbd_map_port(uport);
 		if (ret) {
-			map_guard = atomic_add_return(-1, &duart->map_guard);
-			if (!map_guard)
+			if (refcount_dec_and_test(&duart->map_guard))
 				release_mem_region(duart->mapctrl,
 						   DUART_CHANREG_SPACING);
 		}
diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 3fe56894974a..0f45b7884a2c 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -2117,9 +2117,8 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport)
 		for (tries = 3; !ops->tx_empty(uport) && tries; tries--)
 			msleep(10);
 		if (!tries)
-			dev_err(uport->dev, "%s%d: Unable to drain transmitter\n",
-				drv->dev_name,
-				drv->tty_driver->name_base + uport->line);
+			dev_err(uport->dev, "%s: Unable to drain transmitter\n",
+				uport->name);
 
 		ops->shutdown(uport);
 	}
@@ -2248,11 +2247,10 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
 		break;
 	}
 
-	printk(KERN_INFO "%s%s%s%d at %s (irq = %d, base_baud = %d) is a %s\n",
+	pr_info("%s%s%s at %s (irq = %d, base_baud = %d) is a %s\n",
 	       port->dev ? dev_name(port->dev) : "",
 	       port->dev ? ": " : "",
-	       drv->dev_name,
-	       drv->tty_driver->name_base + port->line,
+	       port->name,
 	       address, port->irq, port->uartclk / 16, uart_type(port));
 }
 
@@ -2331,9 +2329,6 @@ static int uart_poll_init(struct tty_driver *driver, int line, char *options)
 	int flow = 'n';
 	int ret = 0;
 
-	if (!state)
-		return -1;
-
 	tport = &state->port;
 	mutex_lock(&tport->mutex);
 
@@ -2368,13 +2363,12 @@ static int uart_poll_get_char(struct tty_driver *driver, int line)
 	struct uart_port *port;
 	int ret = -1;
 
-	if (state) {
-		port = uart_port_ref(state);
-		if (port) {
-			ret = port->ops->poll_get_char(port);
-			uart_port_deref(port);
-		}
+	port = uart_port_ref(state);
+	if (port) {
+		ret = port->ops->poll_get_char(port);
+		uart_port_deref(port);
 	}
+
 	return ret;
 }
 
@@ -2384,9 +2378,6 @@ static void uart_poll_put_char(struct tty_driver *driver, int line, char ch)
 	struct uart_state *state = drv->state + line;
 	struct uart_port *port;
 
-	if (!state)
-		return;
-
 	port = uart_port_ref(state);
 	if (!port)
 		return;
@@ -2751,6 +2742,12 @@ int uart_add_one_port(struct uart_driver *drv, struct uart_port *uport)
 	state->pm_state = UART_PM_STATE_UNDEFINED;
 	uport->cons = drv->cons;
 	uport->minor = drv->tty_driver->minor_start + uport->line;
+	uport->name = kasprintf(GFP_KERNEL, "%s%d", drv->dev_name,
+				drv->tty_driver->name_base + uport->line);
+	if (!uport->name) {
+		ret = -ENOMEM;
+		goto out;
+	}
 
 	/*
 	 * If this port is a console, then the spinlock is already
@@ -2868,6 +2865,7 @@ int uart_remove_one_port(struct uart_driver *drv, struct uart_port *uport)
 	if (uport->type != PORT_UNKNOWN && uport->ops->release_port)
 		uport->ops->release_port(uport);
 	kfree(uport->tty_groups);
+	kfree(uport->name);
 
 	/*
 	 * Indicate that there isn't a port here anymore.
diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index 9a47cc4f16a2..71707e8e6e3f 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -683,24 +683,37 @@ static void sci_init_pins(struct uart_port *port, unsigned int cflag)
 	}
 
 	if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
+		u16 data = serial_port_in(port, SCPDR);
 		u16 ctrl = serial_port_in(port, SCPCR);
 
 		/* Enable RXD and TXD pin functions */
 		ctrl &= ~(SCPCR_RXDC | SCPCR_TXDC);
 		if (to_sci_port(port)->has_rtscts) {
-			/* RTS# is output, driven 1 */
-			ctrl |= SCPCR_RTSC;
-			serial_port_out(port, SCPDR,
-				serial_port_in(port, SCPDR) | SCPDR_RTSD);
+			/* RTS# is output, active low, unless autorts */
+			if (!(port->mctrl & TIOCM_RTS)) {
+				ctrl |= SCPCR_RTSC;
+				data |= SCPDR_RTSD;
+			} else if (!s->autorts) {
+				ctrl |= SCPCR_RTSC;
+				data &= ~SCPDR_RTSD;
+			} else {
+				/* Enable RTS# pin function */
+				ctrl &= ~SCPCR_RTSC;
+			}
 			/* Enable CTS# pin function */
 			ctrl &= ~SCPCR_CTSC;
 		}
+		serial_port_out(port, SCPDR, data);
 		serial_port_out(port, SCPCR, ctrl);
 	} else if (sci_getreg(port, SCSPTR)->size) {
 		u16 status = serial_port_in(port, SCSPTR);
 
-		/* RTS# is output, driven 1 */
-		status |= SCSPTR_RTSIO | SCSPTR_RTSDT;
+		/* RTS# is always output; and active low, unless autorts */
+		status |= SCSPTR_RTSIO;
+		if (!(port->mctrl & TIOCM_RTS))
+			status |= SCSPTR_RTSDT;
+		else if (!s->autorts)
+			status &= ~SCSPTR_RTSDT;
 		/* CTS# and SCK are inputs */
 		status &= ~(SCSPTR_CTSIO | SCSPTR_SCKIO);
 		serial_port_out(port, SCSPTR, status);
@@ -1985,12 +1998,14 @@ static int sci_startup(struct uart_port *port)
 
 	dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
 
-	ret = sci_request_irq(s);
-	if (unlikely(ret < 0))
-		return ret;
-
 	sci_request_dma(port);
 
+	ret = sci_request_irq(s);
+	if (unlikely(ret < 0)) {
+		sci_free_dma(port);
+		return ret;
+	}
+
 	return 0;
 }
 
@@ -2021,8 +2036,8 @@ static void sci_shutdown(struct uart_port *port)
 	}
 #endif
 
-	sci_free_dma(port);
 	sci_free_irq(s);
+	sci_free_dma(port);
 }
 
 static int sci_sck_calc(struct sci_port *s, unsigned int bps,
@@ -2157,10 +2172,6 @@ static void sci_reset(struct uart_port *port)
 	unsigned int status;
 	struct sci_port *s = to_sci_port(port);
 
-	do {
-		status = serial_port_in(port, SCxSR);
-	} while (!(status & SCxSR_TEND(port)));
-
 	serial_port_out(port, SCSCR, 0x00);	/* TE=0, RE=0, CKE1=0 */
 
 	reg = sci_getreg(port, SCFCR);
@@ -2374,6 +2385,10 @@ done:
 
 		serial_port_out(port, SCFCR, ctrl);
 	}
+	if (port->flags & UPF_HARD_FLOW) {
+		/* Refresh (Auto) RTS */
+		sci_set_mctrl(port, port->mctrl);
+	}
 
 	scr_val |= SCSCR_RE | SCSCR_TE |
 		   (s->cfg->scscr & ~(SCSCR_CKE1 | SCSCR_CKE0));
diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c
index d98e3dc4838e..90996ad97b37 100644
--- a/drivers/tty/serial/sprd_serial.c
+++ b/drivers/tty/serial/sprd_serial.c
@@ -36,7 +36,7 @@
 #define SPRD_FIFO_SIZE		128
 #define SPRD_DEF_RATE		26000000
 #define SPRD_BAUD_IO_LIMIT	3000000
-#define SPRD_TIMEOUT		256
+#define SPRD_TIMEOUT		256000
 
 /* the offset of serial registers and BITs for them */
 /* data registers */
diff --git a/drivers/tty/serial/st-asc.c b/drivers/tty/serial/st-asc.c
index a93a3167a9c6..f5335be344f6 100644
--- a/drivers/tty/serial/st-asc.c
+++ b/drivers/tty/serial/st-asc.c
@@ -887,13 +887,12 @@ static void asc_console_write(struct console *co, const char *s, unsigned count)
 	int locked = 1;
 	u32 intenable;
 
-	local_irq_save(flags);
 	if (port->sysrq)
 		locked = 0; /* asc_interrupt has already claimed the lock */
 	else if (oops_in_progress)
-		locked = spin_trylock(&port->lock);
+		locked = spin_trylock_irqsave(&port->lock, flags);
 	else
-		spin_lock(&port->lock);
+		spin_lock_irqsave(&port->lock, flags);
 
 	/*
 	 * Disable interrupts so we don't get the IRQ line bouncing
@@ -911,14 +910,13 @@ static void asc_console_write(struct console *co, const char *s, unsigned count)
 	asc_out(port, ASC_INTEN, intenable);
 
 	if (locked)
-		spin_unlock(&port->lock);
-	local_irq_restore(flags);
+		spin_unlock_irqrestore(&port->lock, flags);
 }
 
 static int asc_console_setup(struct console *co, char *options)
 {
 	struct asc_port *ascport;
-	int baud = 9600;
+	int baud = 115200;
 	int bits = 8;
 	int parity = 'n';
 	int flow = 'n';
diff --git a/drivers/tty/serial/uartlite.c b/drivers/tty/serial/uartlite.c
index 817bb0d3f326..c9b8d702dadc 100644
--- a/drivers/tty/serial/uartlite.c
+++ b/drivers/tty/serial/uartlite.c
@@ -28,7 +28,7 @@
 #define ULITE_NAME		"ttyUL"
 #define ULITE_MAJOR		204
 #define ULITE_MINOR		187
-#define ULITE_NR_UARTS		16
+#define ULITE_NR_UARTS		CONFIG_SERIAL_UARTLITE_NR_UARTS
 
 /* ---------------------------------------------------------------------
  * Register definitions
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index ad77d0ed0c46..c0539950f8d7 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -30,6 +30,7 @@
 #include <linux/io.h>
 #include <linux/of.h>
 #include <linux/module.h>
+#include <linux/pm_runtime.h>
 
 #define CDNS_UART_TTY_NAME	"ttyPS"
 #define CDNS_UART_NAME		"xuartps"
@@ -176,6 +177,7 @@ MODULE_PARM_DESC(rx_timeout, "Rx timeout, 1-255");
 #define CDNS_UART_BDIV_MIN	4
 #define CDNS_UART_BDIV_MAX	255
 #define CDNS_UART_CD_MAX	65535
+#define UART_AUTOSUSPEND_TIMEOUT	3000
 
 /**
  * struct cdns_uart - device data
@@ -1065,16 +1067,13 @@ static void cdns_uart_poll_put_char(struct uart_port *port, unsigned char c)
 static void cdns_uart_pm(struct uart_port *port, unsigned int state,
 		   unsigned int oldstate)
 {
-	struct cdns_uart *cdns_uart = port->private_data;
-
 	switch (state) {
 	case UART_PM_STATE_OFF:
-		clk_disable(cdns_uart->uartclk);
-		clk_disable(cdns_uart->pclk);
+		pm_runtime_mark_last_busy(port->dev);
+		pm_runtime_put_autosuspend(port->dev);
 		break;
 	default:
-		clk_enable(cdns_uart->pclk);
-		clk_enable(cdns_uart->uartclk);
+		pm_runtime_get_sync(port->dev);
 		break;
 	}
 }
@@ -1353,12 +1352,7 @@ static int cdns_uart_suspend(struct device *device)
 	 * the suspend.
 	 */
 	uart_suspend_port(&cdns_uart_uart_driver, port);
-	if (console_suspend_enabled && !may_wake) {
-		struct cdns_uart *cdns_uart = port->private_data;
-
-		clk_disable(cdns_uart->uartclk);
-		clk_disable(cdns_uart->pclk);
-	} else {
+	if (!(console_suspend_enabled && !may_wake)) {
 		unsigned long flags = 0;
 
 		spin_lock_irqsave(&port->lock, flags);
@@ -1423,6 +1417,8 @@ static int cdns_uart_resume(struct device *device)
 		ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
 		writel(ctrl_reg, port->membase + CDNS_UART_CR);
 
+		clk_disable(cdns_uart->uartclk);
+		clk_disable(cdns_uart->pclk);
 		spin_unlock_irqrestore(&port->lock, flags);
 	} else {
 		spin_lock_irqsave(&port->lock, flags);
@@ -1436,9 +1432,33 @@ static int cdns_uart_resume(struct device *device)
 	return uart_resume_port(&cdns_uart_uart_driver, port);
 }
 #endif /* ! CONFIG_PM_SLEEP */
+static int __maybe_unused cdns_runtime_suspend(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct uart_port *port = platform_get_drvdata(pdev);
+	struct cdns_uart *cdns_uart = port->private_data;
 
-static SIMPLE_DEV_PM_OPS(cdns_uart_dev_pm_ops, cdns_uart_suspend,
-		cdns_uart_resume);
+	clk_disable(cdns_uart->uartclk);
+	clk_disable(cdns_uart->pclk);
+	return 0;
+};
+
+static int __maybe_unused cdns_runtime_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct uart_port *port = platform_get_drvdata(pdev);
+	struct cdns_uart *cdns_uart = port->private_data;
+
+	clk_enable(cdns_uart->pclk);
+	clk_enable(cdns_uart->uartclk);
+	return 0;
+};
+
+static const struct dev_pm_ops cdns_uart_dev_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(cdns_uart_suspend, cdns_uart_resume)
+	SET_RUNTIME_PM_OPS(cdns_runtime_suspend,
+			   cdns_runtime_resume, NULL)
+};
 
 static const struct cdns_platform_data zynqmp_uart_def = {
 				.quirks = CDNS_UART_RXBS_SUPPORT, };
@@ -1501,12 +1521,12 @@ static int cdns_uart_probe(struct platform_device *pdev)
 		return PTR_ERR(cdns_uart_data->uartclk);
 	}
 
-	rc = clk_prepare(cdns_uart_data->pclk);
+	rc = clk_prepare_enable(cdns_uart_data->pclk);
 	if (rc) {
 		dev_err(&pdev->dev, "Unable to enable pclk clock.\n");
 		return rc;
 	}
-	rc = clk_prepare(cdns_uart_data->uartclk);
+	rc = clk_prepare_enable(cdns_uart_data->uartclk);
 	if (rc) {
 		dev_err(&pdev->dev, "Unable to enable device clock.\n");
 		goto err_out_clk_dis_pclk;
@@ -1558,6 +1578,11 @@ static int cdns_uart_probe(struct platform_device *pdev)
 	cdns_uart_data->port = port;
 	platform_set_drvdata(pdev, port);
 
+	pm_runtime_use_autosuspend(&pdev->dev);
+	pm_runtime_set_autosuspend_delay(&pdev->dev, UART_AUTOSUSPEND_TIMEOUT);
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
 	rc = uart_add_one_port(&cdns_uart_uart_driver, port);
 	if (rc) {
 		dev_err(&pdev->dev,
@@ -1573,9 +1598,12 @@ err_out_notif_unreg:
 			&cdns_uart_data->clk_rate_change_nb);
 #endif
 err_out_clk_disable:
-	clk_unprepare(cdns_uart_data->uartclk);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
+	clk_disable_unprepare(cdns_uart_data->uartclk);
 err_out_clk_dis_pclk:
-	clk_unprepare(cdns_uart_data->pclk);
+	clk_disable_unprepare(cdns_uart_data->pclk);
 
 	return rc;
 }
@@ -1599,8 +1627,11 @@ static int cdns_uart_remove(struct platform_device *pdev)
 #endif
 	rc = uart_remove_one_port(&cdns_uart_uart_driver, port);
 	port->mapbase = 0;
-	clk_unprepare(cdns_uart_data->uartclk);
-	clk_unprepare(cdns_uart_data->pclk);
+	clk_disable_unprepare(cdns_uart_data->uartclk);
+	clk_disable_unprepare(cdns_uart_data->pclk);
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_set_suspended(&pdev->dev);
+	pm_runtime_dont_use_autosuspend(&pdev->dev);
 	return rc;
 }
 
diff --git a/drivers/tty/tty_baudrate.c b/drivers/tty/tty_baudrate.c
new file mode 100644
index 000000000000..5c33fd25676d
--- /dev/null
+++ b/drivers/tty/tty_baudrate.c
@@ -0,0 +1,232 @@
+/*
+ *  Copyright (C) 1991, 1992, 1993, 1994  Linus Torvalds
+ */
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/termios.h>
+#include <linux/tty.h>
+#include <linux/export.h>
+
+
+/*
+ * Routine which returns the baud rate of the tty
+ *
+ * Note that the baud_table needs to be kept in sync with the
+ * include/asm/termbits.h file.
+ */
+static const speed_t baud_table[] = {
+	0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
+	9600, 19200, 38400, 57600, 115200, 230400, 460800,
+#ifdef __sparc__
+	76800, 153600, 307200, 614400, 921600
+#else
+	500000, 576000, 921600, 1000000, 1152000, 1500000, 2000000,
+	2500000, 3000000, 3500000, 4000000
+#endif
+};
+
+#ifndef __sparc__
+static const tcflag_t baud_bits[] = {
+	B0, B50, B75, B110, B134, B150, B200, B300, B600,
+	B1200, B1800, B2400, B4800, B9600, B19200, B38400,
+	B57600, B115200, B230400, B460800, B500000, B576000,
+	B921600, B1000000, B1152000, B1500000, B2000000, B2500000,
+	B3000000, B3500000, B4000000
+};
+#else
+static const tcflag_t baud_bits[] = {
+	B0, B50, B75, B110, B134, B150, B200, B300, B600,
+	B1200, B1800, B2400, B4800, B9600, B19200, B38400,
+	B57600, B115200, B230400, B460800, B76800, B153600,
+	B307200, B614400, B921600
+};
+#endif
+
+static int n_baud_table = ARRAY_SIZE(baud_table);
+
+/**
+ *	tty_termios_baud_rate
+ *	@termios: termios structure
+ *
+ *	Convert termios baud rate data into a speed. This should be called
+ *	with the termios lock held if this termios is a terminal termios
+ *	structure. May change the termios data. Device drivers can call this
+ *	function but should use ->c_[io]speed directly as they are updated.
+ *
+ *	Locking: none
+ */
+
+speed_t tty_termios_baud_rate(struct ktermios *termios)
+{
+	unsigned int cbaud;
+
+	cbaud = termios->c_cflag & CBAUD;
+
+#ifdef BOTHER
+	/* Magic token for arbitrary speed via c_ispeed/c_ospeed */
+	if (cbaud == BOTHER)
+		return termios->c_ospeed;
+#endif
+	if (cbaud & CBAUDEX) {
+		cbaud &= ~CBAUDEX;
+
+		if (cbaud < 1 || cbaud + 15 > n_baud_table)
+			termios->c_cflag &= ~CBAUDEX;
+		else
+			cbaud += 15;
+	}
+	return baud_table[cbaud];
+}
+EXPORT_SYMBOL(tty_termios_baud_rate);
+
+/**
+ *	tty_termios_input_baud_rate
+ *	@termios: termios structure
+ *
+ *	Convert termios baud rate data into a speed. This should be called
+ *	with the termios lock held if this termios is a terminal termios
+ *	structure. May change the termios data. Device drivers can call this
+ *	function but should use ->c_[io]speed directly as they are updated.
+ *
+ *	Locking: none
+ */
+
+speed_t tty_termios_input_baud_rate(struct ktermios *termios)
+{
+#ifdef IBSHIFT
+	unsigned int cbaud = (termios->c_cflag >> IBSHIFT) & CBAUD;
+
+	if (cbaud == B0)
+		return tty_termios_baud_rate(termios);
+
+	/* Magic token for arbitrary speed via c_ispeed*/
+	if (cbaud == BOTHER)
+		return termios->c_ispeed;
+
+	if (cbaud & CBAUDEX) {
+		cbaud &= ~CBAUDEX;
+
+		if (cbaud < 1 || cbaud + 15 > n_baud_table)
+			termios->c_cflag &= ~(CBAUDEX << IBSHIFT);
+		else
+			cbaud += 15;
+	}
+	return baud_table[cbaud];
+#else
+	return tty_termios_baud_rate(termios);
+#endif
+}
+EXPORT_SYMBOL(tty_termios_input_baud_rate);
+
+/**
+ *	tty_termios_encode_baud_rate
+ *	@termios: ktermios structure holding user requested state
+ *	@ispeed: input speed
+ *	@ospeed: output speed
+ *
+ *	Encode the speeds set into the passed termios structure. This is
+ *	used as a library helper for drivers so that they can report back
+ *	the actual speed selected when it differs from the speed requested
+ *
+ *	For maximal back compatibility with legacy SYS5/POSIX *nix behaviour
+ *	we need to carefully set the bits when the user does not get the
+ *	desired speed. We allow small margins and preserve as much of possible
+ *	of the input intent to keep compatibility.
+ *
+ *	Locking: Caller should hold termios lock. This is already held
+ *	when calling this function from the driver termios handler.
+ *
+ *	The ifdefs deal with platforms whose owners have yet to update them
+ *	and will all go away once this is done.
+ */
+
+void tty_termios_encode_baud_rate(struct ktermios *termios,
+				  speed_t ibaud, speed_t obaud)
+{
+	int i = 0;
+	int ifound = -1, ofound = -1;
+	int iclose = ibaud/50, oclose = obaud/50;
+	int ibinput = 0;
+
+	if (obaud == 0)			/* CD dropped 		  */
+		ibaud = 0;		/* Clear ibaud to be sure */
+
+	termios->c_ispeed = ibaud;
+	termios->c_ospeed = obaud;
+
+#ifdef BOTHER
+	/* If the user asked for a precise weird speed give a precise weird
+	   answer. If they asked for a Bfoo speed they may have problems
+	   digesting non-exact replies so fuzz a bit */
+
+	if ((termios->c_cflag & CBAUD) == BOTHER)
+		oclose = 0;
+	if (((termios->c_cflag >> IBSHIFT) & CBAUD) == BOTHER)
+		iclose = 0;
+	if ((termios->c_cflag >> IBSHIFT) & CBAUD)
+		ibinput = 1;	/* An input speed was specified */
+#endif
+	termios->c_cflag &= ~CBAUD;
+
+	/*
+	 *	Our goal is to find a close match to the standard baud rate
+	 *	returned. Walk the baud rate table and if we get a very close
+	 *	match then report back the speed as a POSIX Bxxxx value by
+	 *	preference
+	 */
+
+	do {
+		if (obaud - oclose <= baud_table[i] &&
+		    obaud + oclose >= baud_table[i]) {
+			termios->c_cflag |= baud_bits[i];
+			ofound = i;
+		}
+		if (ibaud - iclose <= baud_table[i] &&
+		    ibaud + iclose >= baud_table[i]) {
+			/* For the case input == output don't set IBAUD bits
+			   if the user didn't do so */
+			if (ofound == i && !ibinput)
+				ifound  = i;
+#ifdef IBSHIFT
+			else {
+				ifound = i;
+				termios->c_cflag |= (baud_bits[i] << IBSHIFT);
+			}
+#endif
+		}
+	} while (++i < n_baud_table);
+
+	/*
+	 *	If we found no match then use BOTHER if provided or warn
+	 *	the user their platform maintainer needs to wake up if not.
+	 */
+#ifdef BOTHER
+	if (ofound == -1)
+		termios->c_cflag |= BOTHER;
+	/* Set exact input bits only if the input and output differ or the
+	   user already did */
+	if (ifound == -1 && (ibaud != obaud || ibinput))
+		termios->c_cflag |= (BOTHER << IBSHIFT);
+#else
+	if (ifound == -1 || ofound == -1)
+		pr_warn_once("tty: Unable to return correct speed data as your architecture needs updating.\n");
+#endif
+}
+EXPORT_SYMBOL_GPL(tty_termios_encode_baud_rate);
+
+/**
+ *	tty_encode_baud_rate		-	set baud rate of the tty
+ *	@ibaud: input baud rate
+ *	@obad: output baud rate
+ *
+ *	Update the current termios data for the tty with the new speed
+ *	settings. The caller must hold the termios_rwsem for the tty in
+ *	question.
+ */
+
+void tty_encode_baud_rate(struct tty_struct *tty, speed_t ibaud, speed_t obaud)
+{
+	tty_termios_encode_baud_rate(&tty->termios, ibaud, obaud);
+}
+EXPORT_SYMBOL_GPL(tty_encode_baud_rate);
diff --git a/drivers/tty/tty_io.c b/drivers/tty/tty_io.c
index 309d25065bb6..0c150b5a9dd6 100644
--- a/drivers/tty/tty_io.c
+++ b/drivers/tty/tty_io.c
@@ -377,65 +377,6 @@ struct tty_driver *tty_find_polling_driver(char *name, int *line)
 EXPORT_SYMBOL_GPL(tty_find_polling_driver);
 #endif
 
-static int is_ignored(int sig)
-{
-	return (sigismember(&current->blocked, sig) ||
-		current->sighand->action[sig-1].sa.sa_handler == SIG_IGN);
-}
-
-/**
- *	tty_check_change	-	check for POSIX terminal changes
- *	@tty: tty to check
- *
- *	If we try to write to, or set the state of, a terminal and we're
- *	not in the foreground, send a SIGTTOU.  If the signal is blocked or
- *	ignored, go ahead and perform the operation.  (POSIX 7.2)
- *
- *	Locking: ctrl_lock
- */
-
-int __tty_check_change(struct tty_struct *tty, int sig)
-{
-	unsigned long flags;
-	struct pid *pgrp, *tty_pgrp;
-	int ret = 0;
-
-	if (current->signal->tty != tty)
-		return 0;
-
-	rcu_read_lock();
-	pgrp = task_pgrp(current);
-
-	spin_lock_irqsave(&tty->ctrl_lock, flags);
-	tty_pgrp = tty->pgrp;
-	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
-
-	if (tty_pgrp && pgrp != tty->pgrp) {
-		if (is_ignored(sig)) {
-			if (sig == SIGTTIN)
-				ret = -EIO;
-		} else if (is_current_pgrp_orphaned())
-			ret = -EIO;
-		else {
-			kill_pgrp(pgrp, sig, 1);
-			set_thread_flag(TIF_SIGPENDING);
-			ret = -ERESTARTSYS;
-		}
-	}
-	rcu_read_unlock();
-
-	if (!tty_pgrp)
-		tty_warn(tty, "sig=%d, tty->pgrp == NULL!\n", sig);
-
-	return ret;
-}
-
-int tty_check_change(struct tty_struct *tty)
-{
-	return __tty_check_change(tty, SIGTTOU);
-}
-EXPORT_SYMBOL(tty_check_change);
-
 static ssize_t hung_up_tty_read(struct file *file, char __user *buf,
 				size_t count, loff_t *ppos)
 {
@@ -509,79 +450,6 @@ static const struct file_operations hung_up_tty_fops = {
 static DEFINE_SPINLOCK(redirect_lock);
 static struct file *redirect;
 
-
-void proc_clear_tty(struct task_struct *p)
-{
-	unsigned long flags;
-	struct tty_struct *tty;
-	spin_lock_irqsave(&p->sighand->siglock, flags);
-	tty = p->signal->tty;
-	p->signal->tty = NULL;
-	spin_unlock_irqrestore(&p->sighand->siglock, flags);
-	tty_kref_put(tty);
-}
-
-/**
- * proc_set_tty -  set the controlling terminal
- *
- * Only callable by the session leader and only if it does not already have
- * a controlling terminal.
- *
- * Caller must hold:  tty_lock()
- *		      a readlock on tasklist_lock
- *		      sighand lock
- */
-static void __proc_set_tty(struct tty_struct *tty)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&tty->ctrl_lock, flags);
-	/*
-	 * The session and fg pgrp references will be non-NULL if
-	 * tiocsctty() is stealing the controlling tty
-	 */
-	put_pid(tty->session);
-	put_pid(tty->pgrp);
-	tty->pgrp = get_pid(task_pgrp(current));
-	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
-	tty->session = get_pid(task_session(current));
-	if (current->signal->tty) {
-		tty_debug(tty, "current tty %s not NULL!!\n",
-			  current->signal->tty->name);
-		tty_kref_put(current->signal->tty);
-	}
-	put_pid(current->signal->tty_old_pgrp);
-	current->signal->tty = tty_kref_get(tty);
-	current->signal->tty_old_pgrp = NULL;
-}
-
-static void proc_set_tty(struct tty_struct *tty)
-{
-	spin_lock_irq(&current->sighand->siglock);
-	__proc_set_tty(tty);
-	spin_unlock_irq(&current->sighand->siglock);
-}
-
-struct tty_struct *get_current_tty(void)
-{
-	struct tty_struct *tty;
-	unsigned long flags;
-
-	spin_lock_irqsave(&current->sighand->siglock, flags);
-	tty = tty_kref_get(current->signal->tty);
-	spin_unlock_irqrestore(&current->sighand->siglock, flags);
-	return tty;
-}
-EXPORT_SYMBOL_GPL(get_current_tty);
-
-static void session_clear_tty(struct pid *session)
-{
-	struct task_struct *p;
-	do_each_pid_task(session, PIDTYPE_SID, p) {
-		proc_clear_tty(p);
-	} while_each_pid_task(session, PIDTYPE_SID, p);
-}
-
 /**
  *	tty_wakeup	-	request more data
  *	@tty: terminal
@@ -608,60 +476,6 @@ void tty_wakeup(struct tty_struct *tty)
 
 EXPORT_SYMBOL_GPL(tty_wakeup);
 
-/**
- *	tty_signal_session_leader	- sends SIGHUP to session leader
- *	@tty		controlling tty
- *	@exit_session	if non-zero, signal all foreground group processes
- *
- *	Send SIGHUP and SIGCONT to the session leader and its process group.
- *	Optionally, signal all processes in the foreground process group.
- *
- *	Returns the number of processes in the session with this tty
- *	as their controlling terminal. This value is used to drop
- *	tty references for those processes.
- */
-static int tty_signal_session_leader(struct tty_struct *tty, int exit_session)
-{
-	struct task_struct *p;
-	int refs = 0;
-	struct pid *tty_pgrp = NULL;
-
-	read_lock(&tasklist_lock);
-	if (tty->session) {
-		do_each_pid_task(tty->session, PIDTYPE_SID, p) {
-			spin_lock_irq(&p->sighand->siglock);
-			if (p->signal->tty == tty) {
-				p->signal->tty = NULL;
-				/* We defer the dereferences outside fo
-				   the tasklist lock */
-				refs++;
-			}
-			if (!p->signal->leader) {
-				spin_unlock_irq(&p->sighand->siglock);
-				continue;
-			}
-			__group_send_sig_info(SIGHUP, SEND_SIG_PRIV, p);
-			__group_send_sig_info(SIGCONT, SEND_SIG_PRIV, p);
-			put_pid(p->signal->tty_old_pgrp);  /* A noop */
-			spin_lock(&tty->ctrl_lock);
-			tty_pgrp = get_pid(tty->pgrp);
-			if (tty->pgrp)
-				p->signal->tty_old_pgrp = get_pid(tty->pgrp);
-			spin_unlock(&tty->ctrl_lock);
-			spin_unlock_irq(&p->sighand->siglock);
-		} while_each_pid_task(tty->session, PIDTYPE_SID, p);
-	}
-	read_unlock(&tasklist_lock);
-
-	if (tty_pgrp) {
-		if (exit_session)
-			kill_pgrp(tty_pgrp, SIGHUP, exit_session);
-		put_pid(tty_pgrp);
-	}
-
-	return refs;
-}
-
 /**
  *	__tty_hangup		-	actual handler for hangup events
  *	@work: tty device
@@ -840,7 +654,7 @@ void tty_vhangup_self(void)
  *	is complete. That guarantee is necessary for security reasons.
  */
 
-static void tty_vhangup_session(struct tty_struct *tty)
+void tty_vhangup_session(struct tty_struct *tty)
 {
 	tty_debug_hangup(tty, "session hangup\n");
 	__tty_hangup(tty, 1);
@@ -861,106 +675,6 @@ int tty_hung_up_p(struct file *filp)
 
 EXPORT_SYMBOL(tty_hung_up_p);
 
-/**
- *	disassociate_ctty	-	disconnect controlling tty
- *	@on_exit: true if exiting so need to "hang up" the session
- *
- *	This function is typically called only by the session leader, when
- *	it wants to disassociate itself from its controlling tty.
- *
- *	It performs the following functions:
- * 	(1)  Sends a SIGHUP and SIGCONT to the foreground process group
- * 	(2)  Clears the tty from being controlling the session
- * 	(3)  Clears the controlling tty for all processes in the
- * 		session group.
- *
- *	The argument on_exit is set to 1 if called when a process is
- *	exiting; it is 0 if called by the ioctl TIOCNOTTY.
- *
- *	Locking:
- *		BTM is taken for hysterical raisins, and held when
- *		  called from no_tty().
- *		  tty_mutex is taken to protect tty
- *		  ->siglock is taken to protect ->signal/->sighand
- *		  tasklist_lock is taken to walk process list for sessions
- *		    ->siglock is taken to protect ->signal/->sighand
- */
-
-void disassociate_ctty(int on_exit)
-{
-	struct tty_struct *tty;
-
-	if (!current->signal->leader)
-		return;
-
-	tty = get_current_tty();
-	if (tty) {
-		if (on_exit && tty->driver->type != TTY_DRIVER_TYPE_PTY) {
-			tty_vhangup_session(tty);
-		} else {
-			struct pid *tty_pgrp = tty_get_pgrp(tty);
-			if (tty_pgrp) {
-				kill_pgrp(tty_pgrp, SIGHUP, on_exit);
-				if (!on_exit)
-					kill_pgrp(tty_pgrp, SIGCONT, on_exit);
-				put_pid(tty_pgrp);
-			}
-		}
-		tty_kref_put(tty);
-
-	} else if (on_exit) {
-		struct pid *old_pgrp;
-		spin_lock_irq(&current->sighand->siglock);
-		old_pgrp = current->signal->tty_old_pgrp;
-		current->signal->tty_old_pgrp = NULL;
-		spin_unlock_irq(&current->sighand->siglock);
-		if (old_pgrp) {
-			kill_pgrp(old_pgrp, SIGHUP, on_exit);
-			kill_pgrp(old_pgrp, SIGCONT, on_exit);
-			put_pid(old_pgrp);
-		}
-		return;
-	}
-
-	spin_lock_irq(&current->sighand->siglock);
-	put_pid(current->signal->tty_old_pgrp);
-	current->signal->tty_old_pgrp = NULL;
-
-	tty = tty_kref_get(current->signal->tty);
-	if (tty) {
-		unsigned long flags;
-		spin_lock_irqsave(&tty->ctrl_lock, flags);
-		put_pid(tty->session);
-		put_pid(tty->pgrp);
-		tty->session = NULL;
-		tty->pgrp = NULL;
-		spin_unlock_irqrestore(&tty->ctrl_lock, flags);
-		tty_kref_put(tty);
-	} else
-		tty_debug_hangup(tty, "no current tty\n");
-
-	spin_unlock_irq(&current->sighand->siglock);
-	/* Now clear signal->tty under the lock */
-	read_lock(&tasklist_lock);
-	session_clear_tty(task_session(current));
-	read_unlock(&tasklist_lock);
-}
-
-/**
- *
- *	no_tty	- Ensure the current process does not have a controlling tty
- */
-void no_tty(void)
-{
-	/* FIXME: Review locking here. The tty_lock never covered any race
-	   between a new association and proc_clear_tty but possible we need
-	   to protect against this anyway */
-	struct task_struct *tsk = current;
-	disassociate_ctty(0);
-	proc_clear_tty(tsk);
-}
-
-
 /**
  *	stop_tty	-	propagate flow control
  *	@tty: tty to stop
@@ -1520,7 +1234,7 @@ struct tty_struct *tty_init_dev(struct tty_driver *driver, int idx)
 	 * This code guarantees that either everything succeeds and the
 	 * TTY is ready for operation, or else the table slots are vacated
 	 * and the allocated memory released.  (Except that the termios
-	 * and locked termios may be retained.)
+	 * may be retained.)
 	 */
 
 	if (!try_module_get(driver->owner))
@@ -2163,38 +1877,13 @@ retry_open:
 	}
 	clear_bit(TTY_HUPPED, &tty->flags);
 
-
-	read_lock(&tasklist_lock);
-	spin_lock_irq(&current->sighand->siglock);
 	noctty = (filp->f_flags & O_NOCTTY) ||
-			(IS_ENABLED(CONFIG_VT) && device == MKDEV(TTY_MAJOR, 0)) ||
-			device == MKDEV(TTYAUX_MAJOR, 1) ||
-			(tty->driver->type == TTY_DRIVER_TYPE_PTY &&
-			 tty->driver->subtype == PTY_TYPE_MASTER);
-
-	if (!noctty &&
-	    current->signal->leader &&
-	    !current->signal->tty &&
-	    tty->session == NULL) {
-		/*
-		 * Don't let a process that only has write access to the tty
-		 * obtain the privileges associated with having a tty as
-		 * controlling terminal (being able to reopen it with full
-		 * access through /dev/tty, being able to perform pushback).
-		 * Many distributions set the group of all ttys to "tty" and
-		 * grant write-only access to all terminals for setgid tty
-		 * binaries, which should not imply full privileges on all ttys.
-		 *
-		 * This could theoretically break old code that performs open()
-		 * on a write-only file descriptor. In that case, it might be
-		 * necessary to also permit this if
-		 * inode_permission(inode, MAY_READ) == 0.
-		 */
-		if (filp->f_mode & FMODE_READ)
-			__proc_set_tty(tty);
-	}
-	spin_unlock_irq(&current->sighand->siglock);
-	read_unlock(&tasklist_lock);
+		 (IS_ENABLED(CONFIG_VT) && device == MKDEV(TTY_MAJOR, 0)) ||
+		 device == MKDEV(TTYAUX_MAJOR, 1) ||
+		 (tty->driver->type == TTY_DRIVER_TYPE_PTY &&
+		  tty->driver->subtype == PTY_TYPE_MASTER);
+	if (!noctty)
+		tty_open_proc_set_tty(filp, tty);
 	tty_unlock(tty);
 	return 0;
 }
@@ -2456,211 +2145,6 @@ static int fionbio(struct file *file, int __user *p)
 	return 0;
 }
 
-/**
- *	tiocsctty	-	set controlling tty
- *	@tty: tty structure
- *	@arg: user argument
- *
- *	This ioctl is used to manage job control. It permits a session
- *	leader to set this tty as the controlling tty for the session.
- *
- *	Locking:
- *		Takes tty_lock() to serialize proc_set_tty() for this tty
- *		Takes tasklist_lock internally to walk sessions
- *		Takes ->siglock() when updating signal->tty
- */
-
-static int tiocsctty(struct tty_struct *tty, struct file *file, int arg)
-{
-	int ret = 0;
-
-	tty_lock(tty);
-	read_lock(&tasklist_lock);
-
-	if (current->signal->leader && (task_session(current) == tty->session))
-		goto unlock;
-
-	/*
-	 * The process must be a session leader and
-	 * not have a controlling tty already.
-	 */
-	if (!current->signal->leader || current->signal->tty) {
-		ret = -EPERM;
-		goto unlock;
-	}
-
-	if (tty->session) {
-		/*
-		 * This tty is already the controlling
-		 * tty for another session group!
-		 */
-		if (arg == 1 && capable(CAP_SYS_ADMIN)) {
-			/*
-			 * Steal it away
-			 */
-			session_clear_tty(tty->session);
-		} else {
-			ret = -EPERM;
-			goto unlock;
-		}
-	}
-
-	/* See the comment in tty_open(). */
-	if ((file->f_mode & FMODE_READ) == 0 && !capable(CAP_SYS_ADMIN)) {
-		ret = -EPERM;
-		goto unlock;
-	}
-
-	proc_set_tty(tty);
-unlock:
-	read_unlock(&tasklist_lock);
-	tty_unlock(tty);
-	return ret;
-}
-
-/**
- *	tty_get_pgrp	-	return a ref counted pgrp pid
- *	@tty: tty to read
- *
- *	Returns a refcounted instance of the pid struct for the process
- *	group controlling the tty.
- */
-
-struct pid *tty_get_pgrp(struct tty_struct *tty)
-{
-	unsigned long flags;
-	struct pid *pgrp;
-
-	spin_lock_irqsave(&tty->ctrl_lock, flags);
-	pgrp = get_pid(tty->pgrp);
-	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
-
-	return pgrp;
-}
-EXPORT_SYMBOL_GPL(tty_get_pgrp);
-
-/*
- * This checks not only the pgrp, but falls back on the pid if no
- * satisfactory pgrp is found. I dunno - gdb doesn't work correctly
- * without this...
- *
- * The caller must hold rcu lock or the tasklist lock.
- */
-static struct pid *session_of_pgrp(struct pid *pgrp)
-{
-	struct task_struct *p;
-	struct pid *sid = NULL;
-
-	p = pid_task(pgrp, PIDTYPE_PGID);
-	if (p == NULL)
-		p = pid_task(pgrp, PIDTYPE_PID);
-	if (p != NULL)
-		sid = task_session(p);
-
-	return sid;
-}
-
-/**
- *	tiocgpgrp		-	get process group
- *	@tty: tty passed by user
- *	@real_tty: tty side of the tty passed by the user if a pty else the tty
- *	@p: returned pid
- *
- *	Obtain the process group of the tty. If there is no process group
- *	return an error.
- *
- *	Locking: none. Reference to current->signal->tty is safe.
- */
-
-static int tiocgpgrp(struct tty_struct *tty, struct tty_struct *real_tty, pid_t __user *p)
-{
-	struct pid *pid;
-	int ret;
-	/*
-	 * (tty == real_tty) is a cheap way of
-	 * testing if the tty is NOT a master pty.
-	 */
-	if (tty == real_tty && current->signal->tty != real_tty)
-		return -ENOTTY;
-	pid = tty_get_pgrp(real_tty);
-	ret =  put_user(pid_vnr(pid), p);
-	put_pid(pid);
-	return ret;
-}
-
-/**
- *	tiocspgrp		-	attempt to set process group
- *	@tty: tty passed by user
- *	@real_tty: tty side device matching tty passed by user
- *	@p: pid pointer
- *
- *	Set the process group of the tty to the session passed. Only
- *	permitted where the tty session is our session.
- *
- *	Locking: RCU, ctrl lock
- */
-
-static int tiocspgrp(struct tty_struct *tty, struct tty_struct *real_tty, pid_t __user *p)
-{
-	struct pid *pgrp;
-	pid_t pgrp_nr;
-	int retval = tty_check_change(real_tty);
-
-	if (retval == -EIO)
-		return -ENOTTY;
-	if (retval)
-		return retval;
-	if (!current->signal->tty ||
-	    (current->signal->tty != real_tty) ||
-	    (real_tty->session != task_session(current)))
-		return -ENOTTY;
-	if (get_user(pgrp_nr, p))
-		return -EFAULT;
-	if (pgrp_nr < 0)
-		return -EINVAL;
-	rcu_read_lock();
-	pgrp = find_vpid(pgrp_nr);
-	retval = -ESRCH;
-	if (!pgrp)
-		goto out_unlock;
-	retval = -EPERM;
-	if (session_of_pgrp(pgrp) != task_session(current))
-		goto out_unlock;
-	retval = 0;
-	spin_lock_irq(&tty->ctrl_lock);
-	put_pid(real_tty->pgrp);
-	real_tty->pgrp = get_pid(pgrp);
-	spin_unlock_irq(&tty->ctrl_lock);
-out_unlock:
-	rcu_read_unlock();
-	return retval;
-}
-
-/**
- *	tiocgsid		-	get session id
- *	@tty: tty passed by user
- *	@real_tty: tty side of the tty passed by the user if a pty else the tty
- *	@p: pointer to returned session id
- *
- *	Obtain the session id of the tty. If there is no session
- *	return an error.
- *
- *	Locking: none. Reference to current->signal->tty is safe.
- */
-
-static int tiocgsid(struct tty_struct *tty, struct tty_struct *real_tty, pid_t __user *p)
-{
-	/*
-	 * (tty == real_tty) is a cheap way of
-	 * testing if the tty is NOT a master pty.
-	*/
-	if (tty == real_tty && current->signal->tty != real_tty)
-		return -ENOTTY;
-	if (!real_tty->session)
-		return -ENOTTY;
-	return put_user(pid_vnr(real_tty->session), p);
-}
-
 /**
  *	tiocsetd	-	set line discipline
  *	@tty: tty device
@@ -2843,8 +2327,8 @@ static void tty_warn_deprecated_flags(struct serial_struct __user *ss)
 	flags &= ASYNC_DEPRECATED;
 
 	if (flags && __ratelimit(&depr_flags))
-		pr_warning("%s: '%s' is using deprecated serial flags (with no effect): %.8x\n",
-				__func__, get_task_comm(comm, current), flags);
+		pr_warn("%s: '%s' is using deprecated serial flags (with no effect): %.8x\n",
+			__func__, get_task_comm(comm, current), flags);
 }
 
 /*
@@ -2920,19 +2404,6 @@ long tty_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 		int excl = test_bit(TTY_EXCLUSIVE, &tty->flags);
 		return put_user(excl, (int __user *)p);
 	}
-	case TIOCNOTTY:
-		if (current->signal->tty != tty)
-			return -ENOTTY;
-		no_tty();
-		return 0;
-	case TIOCSCTTY:
-		return tiocsctty(real_tty, file, arg);
-	case TIOCGPGRP:
-		return tiocgpgrp(tty, real_tty, p);
-	case TIOCSPGRP:
-		return tiocspgrp(tty, real_tty, p);
-	case TIOCGSID:
-		return tiocgsid(tty, real_tty, p);
 	case TIOCGETD:
 		return tiocgetd(tty, p);
 	case TIOCSETD:
@@ -2993,6 +2464,10 @@ long tty_ioctl(struct file *file, unsigned int cmd, unsigned long arg)
 	case TIOCSSERIAL:
 		tty_warn_deprecated_flags(p);
 		break;
+	default:
+		retval = tty_jobctrl_ioctl(tty, real_tty, file, cmd, arg);
+		if (retval != -ENOIOCTLCMD)
+			return retval;
 	}
 	if (tty->ops->ioctl) {
 		retval = tty->ops->ioctl(tty, cmd, arg);
@@ -3293,9 +2768,9 @@ struct device *tty_register_device_attr(struct tty_driver *driver,
 {
 	char name[64];
 	dev_t devt = MKDEV(driver->major, driver->minor_start) + index;
-	struct device *dev = NULL;
-	int retval = -ENODEV;
-	bool cdev = false;
+	struct ktermios *tp;
+	struct device *dev;
+	int retval;
 
 	if (index >= driver->num) {
 		pr_err("%s: Attempt to register invalid tty line number (%d)\n",
@@ -3308,18 +2783,9 @@ struct device *tty_register_device_attr(struct tty_driver *driver,
 	else
 		tty_line_name(driver, index, name);
 
-	if (!(driver->flags & TTY_DRIVER_DYNAMIC_ALLOC)) {
-		retval = tty_cdev_add(driver, devt, index, 1);
-		if (retval)
-			goto error;
-		cdev = true;
-	}
-
 	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
-	if (!dev) {
-		retval = -ENOMEM;
-		goto error;
-	}
+	if (!dev)
+		return ERR_PTR(-ENOMEM);
 
 	dev->devt = devt;
 	dev->class = tty_class;
@@ -3329,18 +2795,38 @@ struct device *tty_register_device_attr(struct tty_driver *driver,
 	dev->groups = attr_grp;
 	dev_set_drvdata(dev, drvdata);
 
+	dev_set_uevent_suppress(dev, 1);
+
 	retval = device_register(dev);
 	if (retval)
-		goto error;
+		goto err_put;
+
+	if (!(driver->flags & TTY_DRIVER_DYNAMIC_ALLOC)) {
+		/*
+		 * Free any saved termios data so that the termios state is
+		 * reset when reusing a minor number.
+		 */
+		tp = driver->termios[index];
+		if (tp) {
+			driver->termios[index] = NULL;
+			kfree(tp);
+		}
+
+		retval = tty_cdev_add(driver, devt, index, 1);
+		if (retval)
+			goto err_del;
+	}
+
+	dev_set_uevent_suppress(dev, 0);
+	kobject_uevent(&dev->kobj, KOBJ_ADD);
 
 	return dev;
 
-error:
+err_del:
+	device_del(dev);
+err_put:
 	put_device(dev);
-	if (cdev) {
-		cdev_del(driver->cdevs[index]);
-		driver->cdevs[index] = NULL;
-	}
+
 	return ERR_PTR(retval);
 }
 EXPORT_SYMBOL_GPL(tty_register_device_attr);
@@ -3441,11 +2927,6 @@ static void destruct_tty_driver(struct kref *kref)
 	struct ktermios *tp;
 
 	if (driver->flags & TTY_DRIVER_INSTALLED) {
-		/*
-		 * Free the termios and termios_locked structures because
-		 * we don't want to get memory leaks when modular tty
-		 * drivers are removed from the kernel.
-		 */
 		for (i = 0; i < driver->num; i++) {
 			tp = driver->termios[i];
 			if (tp) {
@@ -3578,30 +3059,6 @@ void tty_default_fops(struct file_operations *fops)
 	*fops = tty_fops;
 }
 
-/*
- * Initialize the console device. This is called *early*, so
- * we can't necessarily depend on lots of kernel help here.
- * Just do some early initializations, and do the complex setup
- * later.
- */
-void __init console_init(void)
-{
-	initcall_t *call;
-
-	/* Setup the default TTY line discipline. */
-	n_tty_init();
-
-	/*
-	 * set up the console device so that later boot sequences can
-	 * inform about problems etc..
-	 */
-	call = __con_initcall_start;
-	while (call < __con_initcall_end) {
-		(*call)();
-		call++;
-	}
-}
-
 static char *tty_devnode(struct device *dev, umode_t *mode)
 {
 	if (!mode)
diff --git a/drivers/tty/tty_ioctl.c b/drivers/tty/tty_ioctl.c
index a9a978731c5b..efa96e6c4c1b 100644
--- a/drivers/tty/tty_ioctl.c
+++ b/drivers/tty/tty_ioctl.c
@@ -258,228 +258,6 @@ static void unset_locked_termios(struct tty_struct *tty, struct ktermios *old)
 	/* FIXME: What should we do for i/ospeed */
 }
 
-/*
- * Routine which returns the baud rate of the tty
- *
- * Note that the baud_table needs to be kept in sync with the
- * include/asm/termbits.h file.
- */
-static const speed_t baud_table[] = {
-	0, 50, 75, 110, 134, 150, 200, 300, 600, 1200, 1800, 2400, 4800,
-	9600, 19200, 38400, 57600, 115200, 230400, 460800,
-#ifdef __sparc__
-	76800, 153600, 307200, 614400, 921600
-#else
-	500000, 576000, 921600, 1000000, 1152000, 1500000, 2000000,
-	2500000, 3000000, 3500000, 4000000
-#endif
-};
-
-#ifndef __sparc__
-static const tcflag_t baud_bits[] = {
-	B0, B50, B75, B110, B134, B150, B200, B300, B600,
-	B1200, B1800, B2400, B4800, B9600, B19200, B38400,
-	B57600, B115200, B230400, B460800, B500000, B576000,
-	B921600, B1000000, B1152000, B1500000, B2000000, B2500000,
-	B3000000, B3500000, B4000000
-};
-#else
-static const tcflag_t baud_bits[] = {
-	B0, B50, B75, B110, B134, B150, B200, B300, B600,
-	B1200, B1800, B2400, B4800, B9600, B19200, B38400,
-	B57600, B115200, B230400, B460800, B76800, B153600,
-	B307200, B614400, B921600
-};
-#endif
-
-static int n_baud_table = ARRAY_SIZE(baud_table);
-
-/**
- *	tty_termios_baud_rate
- *	@termios: termios structure
- *
- *	Convert termios baud rate data into a speed. This should be called
- *	with the termios lock held if this termios is a terminal termios
- *	structure. May change the termios data. Device drivers can call this
- *	function but should use ->c_[io]speed directly as they are updated.
- *
- *	Locking: none
- */
-
-speed_t tty_termios_baud_rate(struct ktermios *termios)
-{
-	unsigned int cbaud;
-
-	cbaud = termios->c_cflag & CBAUD;
-
-#ifdef BOTHER
-	/* Magic token for arbitrary speed via c_ispeed/c_ospeed */
-	if (cbaud == BOTHER)
-		return termios->c_ospeed;
-#endif
-	if (cbaud & CBAUDEX) {
-		cbaud &= ~CBAUDEX;
-
-		if (cbaud < 1 || cbaud + 15 > n_baud_table)
-			termios->c_cflag &= ~CBAUDEX;
-		else
-			cbaud += 15;
-	}
-	return baud_table[cbaud];
-}
-EXPORT_SYMBOL(tty_termios_baud_rate);
-
-/**
- *	tty_termios_input_baud_rate
- *	@termios: termios structure
- *
- *	Convert termios baud rate data into a speed. This should be called
- *	with the termios lock held if this termios is a terminal termios
- *	structure. May change the termios data. Device drivers can call this
- *	function but should use ->c_[io]speed directly as they are updated.
- *
- *	Locking: none
- */
-
-speed_t tty_termios_input_baud_rate(struct ktermios *termios)
-{
-#ifdef IBSHIFT
-	unsigned int cbaud = (termios->c_cflag >> IBSHIFT) & CBAUD;
-
-	if (cbaud == B0)
-		return tty_termios_baud_rate(termios);
-
-	/* Magic token for arbitrary speed via c_ispeed*/
-	if (cbaud == BOTHER)
-		return termios->c_ispeed;
-
-	if (cbaud & CBAUDEX) {
-		cbaud &= ~CBAUDEX;
-
-		if (cbaud < 1 || cbaud + 15 > n_baud_table)
-			termios->c_cflag &= ~(CBAUDEX << IBSHIFT);
-		else
-			cbaud += 15;
-	}
-	return baud_table[cbaud];
-#else
-	return tty_termios_baud_rate(termios);
-#endif
-}
-EXPORT_SYMBOL(tty_termios_input_baud_rate);
-
-/**
- *	tty_termios_encode_baud_rate
- *	@termios: ktermios structure holding user requested state
- *	@ispeed: input speed
- *	@ospeed: output speed
- *
- *	Encode the speeds set into the passed termios structure. This is
- *	used as a library helper for drivers so that they can report back
- *	the actual speed selected when it differs from the speed requested
- *
- *	For maximal back compatibility with legacy SYS5/POSIX *nix behaviour
- *	we need to carefully set the bits when the user does not get the
- *	desired speed. We allow small margins and preserve as much of possible
- *	of the input intent to keep compatibility.
- *
- *	Locking: Caller should hold termios lock. This is already held
- *	when calling this function from the driver termios handler.
- *
- *	The ifdefs deal with platforms whose owners have yet to update them
- *	and will all go away once this is done.
- */
-
-void tty_termios_encode_baud_rate(struct ktermios *termios,
-				  speed_t ibaud, speed_t obaud)
-{
-	int i = 0;
-	int ifound = -1, ofound = -1;
-	int iclose = ibaud/50, oclose = obaud/50;
-	int ibinput = 0;
-
-	if (obaud == 0)			/* CD dropped 		  */
-		ibaud = 0;		/* Clear ibaud to be sure */
-
-	termios->c_ispeed = ibaud;
-	termios->c_ospeed = obaud;
-
-#ifdef BOTHER
-	/* If the user asked for a precise weird speed give a precise weird
-	   answer. If they asked for a Bfoo speed they may have problems
-	   digesting non-exact replies so fuzz a bit */
-
-	if ((termios->c_cflag & CBAUD) == BOTHER)
-		oclose = 0;
-	if (((termios->c_cflag >> IBSHIFT) & CBAUD) == BOTHER)
-		iclose = 0;
-	if ((termios->c_cflag >> IBSHIFT) & CBAUD)
-		ibinput = 1;	/* An input speed was specified */
-#endif
-	termios->c_cflag &= ~CBAUD;
-
-	/*
-	 *	Our goal is to find a close match to the standard baud rate
-	 *	returned. Walk the baud rate table and if we get a very close
-	 *	match then report back the speed as a POSIX Bxxxx value by
-	 *	preference
-	 */
-
-	do {
-		if (obaud - oclose <= baud_table[i] &&
-		    obaud + oclose >= baud_table[i]) {
-			termios->c_cflag |= baud_bits[i];
-			ofound = i;
-		}
-		if (ibaud - iclose <= baud_table[i] &&
-		    ibaud + iclose >= baud_table[i]) {
-			/* For the case input == output don't set IBAUD bits
-			   if the user didn't do so */
-			if (ofound == i && !ibinput)
-				ifound  = i;
-#ifdef IBSHIFT
-			else {
-				ifound = i;
-				termios->c_cflag |= (baud_bits[i] << IBSHIFT);
-			}
-#endif
-		}
-	} while (++i < n_baud_table);
-
-	/*
-	 *	If we found no match then use BOTHER if provided or warn
-	 *	the user their platform maintainer needs to wake up if not.
-	 */
-#ifdef BOTHER
-	if (ofound == -1)
-		termios->c_cflag |= BOTHER;
-	/* Set exact input bits only if the input and output differ or the
-	   user already did */
-	if (ifound == -1 && (ibaud != obaud || ibinput))
-		termios->c_cflag |= (BOTHER << IBSHIFT);
-#else
-	if (ifound == -1 || ofound == -1)
-		pr_warn_once("tty: Unable to return correct speed data as your architecture needs updating.\n");
-#endif
-}
-EXPORT_SYMBOL_GPL(tty_termios_encode_baud_rate);
-
-/**
- *	tty_encode_baud_rate		-	set baud rate of the tty
- *	@ibaud: input baud rate
- *	@obad: output baud rate
- *
- *	Update the current termios data for the tty with the new speed
- *	settings. The caller must hold the termios_rwsem for the tty in
- *	question.
- */
-
-void tty_encode_baud_rate(struct tty_struct *tty, speed_t ibaud, speed_t obaud)
-{
-	tty_termios_encode_baud_rate(&tty->termios, ibaud, obaud);
-}
-EXPORT_SYMBOL_GPL(tty_encode_baud_rate);
-
 /**
  *	tty_termios_copy_hw	-	copy hardware settings
  *	@new: New termios
diff --git a/drivers/tty/tty_jobctrl.c b/drivers/tty/tty_jobctrl.c
new file mode 100644
index 000000000000..e7032309ee87
--- /dev/null
+++ b/drivers/tty/tty_jobctrl.c
@@ -0,0 +1,554 @@
+/*
+ *  Copyright (C) 1991, 1992  Linus Torvalds
+ */
+
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/signal.h>
+#include <linux/sched/signal.h>
+#include <linux/sched/task.h>
+#include <linux/tty.h>
+#include <linux/fcntl.h>
+#include <linux/uaccess.h>
+
+static int is_ignored(int sig)
+{
+	return (sigismember(&current->blocked, sig) ||
+		current->sighand->action[sig-1].sa.sa_handler == SIG_IGN);
+}
+
+/**
+ *	tty_check_change	-	check for POSIX terminal changes
+ *	@tty: tty to check
+ *
+ *	If we try to write to, or set the state of, a terminal and we're
+ *	not in the foreground, send a SIGTTOU.  If the signal is blocked or
+ *	ignored, go ahead and perform the operation.  (POSIX 7.2)
+ *
+ *	Locking: ctrl_lock
+ */
+int __tty_check_change(struct tty_struct *tty, int sig)
+{
+	unsigned long flags;
+	struct pid *pgrp, *tty_pgrp;
+	int ret = 0;
+
+	if (current->signal->tty != tty)
+		return 0;
+
+	rcu_read_lock();
+	pgrp = task_pgrp(current);
+
+	spin_lock_irqsave(&tty->ctrl_lock, flags);
+	tty_pgrp = tty->pgrp;
+	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+
+	if (tty_pgrp && pgrp != tty->pgrp) {
+		if (is_ignored(sig)) {
+			if (sig == SIGTTIN)
+				ret = -EIO;
+		} else if (is_current_pgrp_orphaned())
+			ret = -EIO;
+		else {
+			kill_pgrp(pgrp, sig, 1);
+			set_thread_flag(TIF_SIGPENDING);
+			ret = -ERESTARTSYS;
+		}
+	}
+	rcu_read_unlock();
+
+	if (!tty_pgrp)
+		tty_warn(tty, "sig=%d, tty->pgrp == NULL!\n", sig);
+
+	return ret;
+}
+
+int tty_check_change(struct tty_struct *tty)
+{
+	return __tty_check_change(tty, SIGTTOU);
+}
+EXPORT_SYMBOL(tty_check_change);
+
+void proc_clear_tty(struct task_struct *p)
+{
+	unsigned long flags;
+	struct tty_struct *tty;
+	spin_lock_irqsave(&p->sighand->siglock, flags);
+	tty = p->signal->tty;
+	p->signal->tty = NULL;
+	spin_unlock_irqrestore(&p->sighand->siglock, flags);
+	tty_kref_put(tty);
+}
+
+/**
+ * proc_set_tty -  set the controlling terminal
+ *
+ * Only callable by the session leader and only if it does not already have
+ * a controlling terminal.
+ *
+ * Caller must hold:  tty_lock()
+ *		      a readlock on tasklist_lock
+ *		      sighand lock
+ */
+static void __proc_set_tty(struct tty_struct *tty)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&tty->ctrl_lock, flags);
+	/*
+	 * The session and fg pgrp references will be non-NULL if
+	 * tiocsctty() is stealing the controlling tty
+	 */
+	put_pid(tty->session);
+	put_pid(tty->pgrp);
+	tty->pgrp = get_pid(task_pgrp(current));
+	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+	tty->session = get_pid(task_session(current));
+	if (current->signal->tty) {
+		tty_debug(tty, "current tty %s not NULL!!\n",
+			  current->signal->tty->name);
+		tty_kref_put(current->signal->tty);
+	}
+	put_pid(current->signal->tty_old_pgrp);
+	current->signal->tty = tty_kref_get(tty);
+	current->signal->tty_old_pgrp = NULL;
+}
+
+static void proc_set_tty(struct tty_struct *tty)
+{
+	spin_lock_irq(&current->sighand->siglock);
+	__proc_set_tty(tty);
+	spin_unlock_irq(&current->sighand->siglock);
+}
+
+/*
+ * Called by tty_open() to set the controlling tty if applicable.
+ */
+void tty_open_proc_set_tty(struct file *filp, struct tty_struct *tty)
+{
+	read_lock(&tasklist_lock);
+	spin_lock_irq(&current->sighand->siglock);
+	if (current->signal->leader &&
+	    !current->signal->tty &&
+	    tty->session == NULL) {
+		/*
+		 * Don't let a process that only has write access to the tty
+		 * obtain the privileges associated with having a tty as
+		 * controlling terminal (being able to reopen it with full
+		 * access through /dev/tty, being able to perform pushback).
+		 * Many distributions set the group of all ttys to "tty" and
+		 * grant write-only access to all terminals for setgid tty
+		 * binaries, which should not imply full privileges on all ttys.
+		 *
+		 * This could theoretically break old code that performs open()
+		 * on a write-only file descriptor. In that case, it might be
+		 * necessary to also permit this if
+		 * inode_permission(inode, MAY_READ) == 0.
+		 */
+		if (filp->f_mode & FMODE_READ)
+			__proc_set_tty(tty);
+	}
+	spin_unlock_irq(&current->sighand->siglock);
+	read_unlock(&tasklist_lock);
+}
+
+struct tty_struct *get_current_tty(void)
+{
+	struct tty_struct *tty;
+	unsigned long flags;
+
+	spin_lock_irqsave(&current->sighand->siglock, flags);
+	tty = tty_kref_get(current->signal->tty);
+	spin_unlock_irqrestore(&current->sighand->siglock, flags);
+	return tty;
+}
+EXPORT_SYMBOL_GPL(get_current_tty);
+
+/*
+ * Called from tty_release().
+ */
+void session_clear_tty(struct pid *session)
+{
+	struct task_struct *p;
+	do_each_pid_task(session, PIDTYPE_SID, p) {
+		proc_clear_tty(p);
+	} while_each_pid_task(session, PIDTYPE_SID, p);
+}
+
+/**
+ *	tty_signal_session_leader	- sends SIGHUP to session leader
+ *	@tty		controlling tty
+ *	@exit_session	if non-zero, signal all foreground group processes
+ *
+ *	Send SIGHUP and SIGCONT to the session leader and its process group.
+ *	Optionally, signal all processes in the foreground process group.
+ *
+ *	Returns the number of processes in the session with this tty
+ *	as their controlling terminal. This value is used to drop
+ *	tty references for those processes.
+ */
+int tty_signal_session_leader(struct tty_struct *tty, int exit_session)
+{
+	struct task_struct *p;
+	int refs = 0;
+	struct pid *tty_pgrp = NULL;
+
+	read_lock(&tasklist_lock);
+	if (tty->session) {
+		do_each_pid_task(tty->session, PIDTYPE_SID, p) {
+			spin_lock_irq(&p->sighand->siglock);
+			if (p->signal->tty == tty) {
+				p->signal->tty = NULL;
+				/* We defer the dereferences outside fo
+				   the tasklist lock */
+				refs++;
+			}
+			if (!p->signal->leader) {
+				spin_unlock_irq(&p->sighand->siglock);
+				continue;
+			}
+			__group_send_sig_info(SIGHUP, SEND_SIG_PRIV, p);
+			__group_send_sig_info(SIGCONT, SEND_SIG_PRIV, p);
+			put_pid(p->signal->tty_old_pgrp);  /* A noop */
+			spin_lock(&tty->ctrl_lock);
+			tty_pgrp = get_pid(tty->pgrp);
+			if (tty->pgrp)
+				p->signal->tty_old_pgrp = get_pid(tty->pgrp);
+			spin_unlock(&tty->ctrl_lock);
+			spin_unlock_irq(&p->sighand->siglock);
+		} while_each_pid_task(tty->session, PIDTYPE_SID, p);
+	}
+	read_unlock(&tasklist_lock);
+
+	if (tty_pgrp) {
+		if (exit_session)
+			kill_pgrp(tty_pgrp, SIGHUP, exit_session);
+		put_pid(tty_pgrp);
+	}
+
+	return refs;
+}
+
+/**
+ *	disassociate_ctty	-	disconnect controlling tty
+ *	@on_exit: true if exiting so need to "hang up" the session
+ *
+ *	This function is typically called only by the session leader, when
+ *	it wants to disassociate itself from its controlling tty.
+ *
+ *	It performs the following functions:
+ * 	(1)  Sends a SIGHUP and SIGCONT to the foreground process group
+ * 	(2)  Clears the tty from being controlling the session
+ * 	(3)  Clears the controlling tty for all processes in the
+ * 		session group.
+ *
+ *	The argument on_exit is set to 1 if called when a process is
+ *	exiting; it is 0 if called by the ioctl TIOCNOTTY.
+ *
+ *	Locking:
+ *		BTM is taken for hysterical raisons, and held when
+ *		  called from no_tty().
+ *		  tty_mutex is taken to protect tty
+ *		  ->siglock is taken to protect ->signal/->sighand
+ *		  tasklist_lock is taken to walk process list for sessions
+ *		    ->siglock is taken to protect ->signal/->sighand
+ */
+void disassociate_ctty(int on_exit)
+{
+	struct tty_struct *tty;
+
+	if (!current->signal->leader)
+		return;
+
+	tty = get_current_tty();
+	if (tty) {
+		if (on_exit && tty->driver->type != TTY_DRIVER_TYPE_PTY) {
+			tty_vhangup_session(tty);
+		} else {
+			struct pid *tty_pgrp = tty_get_pgrp(tty);
+			if (tty_pgrp) {
+				kill_pgrp(tty_pgrp, SIGHUP, on_exit);
+				if (!on_exit)
+					kill_pgrp(tty_pgrp, SIGCONT, on_exit);
+				put_pid(tty_pgrp);
+			}
+		}
+		tty_kref_put(tty);
+
+	} else if (on_exit) {
+		struct pid *old_pgrp;
+		spin_lock_irq(&current->sighand->siglock);
+		old_pgrp = current->signal->tty_old_pgrp;
+		current->signal->tty_old_pgrp = NULL;
+		spin_unlock_irq(&current->sighand->siglock);
+		if (old_pgrp) {
+			kill_pgrp(old_pgrp, SIGHUP, on_exit);
+			kill_pgrp(old_pgrp, SIGCONT, on_exit);
+			put_pid(old_pgrp);
+		}
+		return;
+	}
+
+	spin_lock_irq(&current->sighand->siglock);
+	put_pid(current->signal->tty_old_pgrp);
+	current->signal->tty_old_pgrp = NULL;
+
+	tty = tty_kref_get(current->signal->tty);
+	if (tty) {
+		unsigned long flags;
+		spin_lock_irqsave(&tty->ctrl_lock, flags);
+		put_pid(tty->session);
+		put_pid(tty->pgrp);
+		tty->session = NULL;
+		tty->pgrp = NULL;
+		spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+		tty_kref_put(tty);
+	}
+
+	spin_unlock_irq(&current->sighand->siglock);
+	/* Now clear signal->tty under the lock */
+	read_lock(&tasklist_lock);
+	session_clear_tty(task_session(current));
+	read_unlock(&tasklist_lock);
+}
+
+/**
+ *
+ *	no_tty	- Ensure the current process does not have a controlling tty
+ */
+void no_tty(void)
+{
+	/* FIXME: Review locking here. The tty_lock never covered any race
+	   between a new association and proc_clear_tty but possible we need
+	   to protect against this anyway */
+	struct task_struct *tsk = current;
+	disassociate_ctty(0);
+	proc_clear_tty(tsk);
+}
+
+/**
+ *	tiocsctty	-	set controlling tty
+ *	@tty: tty structure
+ *	@arg: user argument
+ *
+ *	This ioctl is used to manage job control. It permits a session
+ *	leader to set this tty as the controlling tty for the session.
+ *
+ *	Locking:
+ *		Takes tty_lock() to serialize proc_set_tty() for this tty
+ *		Takes tasklist_lock internally to walk sessions
+ *		Takes ->siglock() when updating signal->tty
+ */
+static int tiocsctty(struct tty_struct *tty, struct file *file, int arg)
+{
+	int ret = 0;
+
+	tty_lock(tty);
+	read_lock(&tasklist_lock);
+
+	if (current->signal->leader && (task_session(current) == tty->session))
+		goto unlock;
+
+	/*
+	 * The process must be a session leader and
+	 * not have a controlling tty already.
+	 */
+	if (!current->signal->leader || current->signal->tty) {
+		ret = -EPERM;
+		goto unlock;
+	}
+
+	if (tty->session) {
+		/*
+		 * This tty is already the controlling
+		 * tty for another session group!
+		 */
+		if (arg == 1 && capable(CAP_SYS_ADMIN)) {
+			/*
+			 * Steal it away
+			 */
+			session_clear_tty(tty->session);
+		} else {
+			ret = -EPERM;
+			goto unlock;
+		}
+	}
+
+	/* See the comment in tty_open_proc_set_tty(). */
+	if ((file->f_mode & FMODE_READ) == 0 && !capable(CAP_SYS_ADMIN)) {
+		ret = -EPERM;
+		goto unlock;
+	}
+
+	proc_set_tty(tty);
+unlock:
+	read_unlock(&tasklist_lock);
+	tty_unlock(tty);
+	return ret;
+}
+
+/**
+ *	tty_get_pgrp	-	return a ref counted pgrp pid
+ *	@tty: tty to read
+ *
+ *	Returns a refcounted instance of the pid struct for the process
+ *	group controlling the tty.
+ */
+struct pid *tty_get_pgrp(struct tty_struct *tty)
+{
+	unsigned long flags;
+	struct pid *pgrp;
+
+	spin_lock_irqsave(&tty->ctrl_lock, flags);
+	pgrp = get_pid(tty->pgrp);
+	spin_unlock_irqrestore(&tty->ctrl_lock, flags);
+
+	return pgrp;
+}
+EXPORT_SYMBOL_GPL(tty_get_pgrp);
+
+/*
+ * This checks not only the pgrp, but falls back on the pid if no
+ * satisfactory pgrp is found. I dunno - gdb doesn't work correctly
+ * without this...
+ *
+ * The caller must hold rcu lock or the tasklist lock.
+ */
+static struct pid *session_of_pgrp(struct pid *pgrp)
+{
+	struct task_struct *p;
+	struct pid *sid = NULL;
+
+	p = pid_task(pgrp, PIDTYPE_PGID);
+	if (p == NULL)
+		p = pid_task(pgrp, PIDTYPE_PID);
+	if (p != NULL)
+		sid = task_session(p);
+
+	return sid;
+}
+
+/**
+ *	tiocgpgrp		-	get process group
+ *	@tty: tty passed by user
+ *	@real_tty: tty side of the tty passed by the user if a pty else the tty
+ *	@p: returned pid
+ *
+ *	Obtain the process group of the tty. If there is no process group
+ *	return an error.
+ *
+ *	Locking: none. Reference to current->signal->tty is safe.
+ */
+static int tiocgpgrp(struct tty_struct *tty, struct tty_struct *real_tty, pid_t __user *p)
+{
+	struct pid *pid;
+	int ret;
+	/*
+	 * (tty == real_tty) is a cheap way of
+	 * testing if the tty is NOT a master pty.
+	 */
+	if (tty == real_tty && current->signal->tty != real_tty)
+		return -ENOTTY;
+	pid = tty_get_pgrp(real_tty);
+	ret =  put_user(pid_vnr(pid), p);
+	put_pid(pid);
+	return ret;
+}
+
+/**
+ *	tiocspgrp		-	attempt to set process group
+ *	@tty: tty passed by user
+ *	@real_tty: tty side device matching tty passed by user
+ *	@p: pid pointer
+ *
+ *	Set the process group of the tty to the session passed. Only
+ *	permitted where the tty session is our session.
+ *
+ *	Locking: RCU, ctrl lock
+ */
+static int tiocspgrp(struct tty_struct *tty, struct tty_struct *real_tty, pid_t __user *p)
+{
+	struct pid *pgrp;
+	pid_t pgrp_nr;
+	int retval = tty_check_change(real_tty);
+
+	if (retval == -EIO)
+		return -ENOTTY;
+	if (retval)
+		return retval;
+	if (!current->signal->tty ||
+	    (current->signal->tty != real_tty) ||
+	    (real_tty->session != task_session(current)))
+		return -ENOTTY;
+	if (get_user(pgrp_nr, p))
+		return -EFAULT;
+	if (pgrp_nr < 0)
+		return -EINVAL;
+	rcu_read_lock();
+	pgrp = find_vpid(pgrp_nr);
+	retval = -ESRCH;
+	if (!pgrp)
+		goto out_unlock;
+	retval = -EPERM;
+	if (session_of_pgrp(pgrp) != task_session(current))
+		goto out_unlock;
+	retval = 0;
+	spin_lock_irq(&tty->ctrl_lock);
+	put_pid(real_tty->pgrp);
+	real_tty->pgrp = get_pid(pgrp);
+	spin_unlock_irq(&tty->ctrl_lock);
+out_unlock:
+	rcu_read_unlock();
+	return retval;
+}
+
+/**
+ *	tiocgsid		-	get session id
+ *	@tty: tty passed by user
+ *	@real_tty: tty side of the tty passed by the user if a pty else the tty
+ *	@p: pointer to returned session id
+ *
+ *	Obtain the session id of the tty. If there is no session
+ *	return an error.
+ *
+ *	Locking: none. Reference to current->signal->tty is safe.
+ */
+static int tiocgsid(struct tty_struct *tty, struct tty_struct *real_tty, pid_t __user *p)
+{
+	/*
+	 * (tty == real_tty) is a cheap way of
+	 * testing if the tty is NOT a master pty.
+	*/
+	if (tty == real_tty && current->signal->tty != real_tty)
+		return -ENOTTY;
+	if (!real_tty->session)
+		return -ENOTTY;
+	return put_user(pid_vnr(real_tty->session), p);
+}
+
+/*
+ * Called from tty_ioctl(). If tty is a pty then real_tty is the slave side,
+ * if not then tty == real_tty.
+ */
+long tty_jobctrl_ioctl(struct tty_struct *tty, struct tty_struct *real_tty,
+		       struct file *file, unsigned int cmd, unsigned long arg)
+{
+	void __user *p = (void __user *)arg;
+
+	switch (cmd) {
+	case TIOCNOTTY:
+		if (current->signal->tty != tty)
+			return -ENOTTY;
+		no_tty();
+		return 0;
+	case TIOCSCTTY:
+		return tiocsctty(real_tty, file, arg);
+	case TIOCGPGRP:
+		return tiocgpgrp(tty, real_tty, p);
+	case TIOCSPGRP:
+		return tiocspgrp(tty, real_tty, p);
+	case TIOCGSID:
+		return tiocgsid(tty, real_tty, p);
+	}
+	return -ENOIOCTLCMD;
+}
diff --git a/drivers/tty/vt/selection.c b/drivers/tty/vt/selection.c
index 36e1b8c7680f..accbd1257bc4 100644
--- a/drivers/tty/vt/selection.c
+++ b/drivers/tty/vt/selection.c
@@ -80,21 +80,17 @@ void clear_selection(void)
 
 /*
  * User settable table: what characters are to be considered alphabetic?
- * 256 bits. Locked by the console lock.
+ * 128 bits. Locked by the console lock.
  */
-static u32 inwordLut[8]={
+static u32 inwordLut[]={
   0x00000000, /* control chars     */
-  0x03FF0000, /* digits            */
+  0x03FFE000, /* digits and "-./"  */
   0x87FFFFFE, /* uppercase and '_' */
   0x07FFFFFE, /* lowercase         */
-  0x00000000,
-  0x00000000,
-  0xFF7FFFFF, /* latin-1 accented letters, not multiplication sign */
-  0xFF7FFFFF  /* latin-1 accented letters, not division sign */
 };
 
 static inline int inword(const u16 c) {
-	return c > 0xff || (( inwordLut[c>>5] >> (c & 0x1F) ) & 1);
+	return c > 0x7f || (( inwordLut[c>>5] >> (c & 0x1F) ) & 1);
 }
 
 /**
@@ -106,10 +102,10 @@ static inline int inword(const u16 c) {
  */
 int sel_loadlut(char __user *p)
 {
-	u32 tmplut[8];
-	if (copy_from_user(tmplut, (u32 __user *)(p+4), 32))
+	u32 tmplut[ARRAY_SIZE(inwordLut)];
+	if (copy_from_user(tmplut, (u32 __user *)(p+4), sizeof(inwordLut)))
 		return -EFAULT;
-	memcpy(inwordLut, tmplut, 32);
+	memcpy(inwordLut, tmplut, sizeof(inwordLut));
 	return 0;
 }
 
diff --git a/drivers/tty/vt/vt.c b/drivers/tty/vt/vt.c
index 5c4933bb4b53..9c9945284bcf 100644
--- a/drivers/tty/vt/vt.c
+++ b/drivers/tty/vt/vt.c
@@ -181,7 +181,7 @@ int console_blanked;
 
 static int vesa_blank_mode; /* 0:none 1:suspendV 2:suspendH 3:powerdown */
 static int vesa_off_interval;
-static int blankinterval = 10*60;
+static int blankinterval;
 core_param(consoleblank, blankinterval, int, 0444);
 
 static DECLARE_WORK(console_work, console_callback);
diff --git a/include/linux/console.h b/include/linux/console.h
index 5949d1855589..b8920a031a3e 100644
--- a/include/linux/console.h
+++ b/include/linux/console.h
@@ -212,4 +212,6 @@ extern bool vgacon_text_force(void);
 static inline bool vgacon_text_force(void) { return false; }
 #endif
 
+extern void console_init(void);
+
 #endif /* _LINUX_CONSOLE_H */
diff --git a/include/linux/serdev.h b/include/linux/serdev.h
index 37395b8eb8f1..cda76c6506ca 100644
--- a/include/linux/serdev.h
+++ b/include/linux/serdev.h
@@ -41,12 +41,16 @@ struct serdev_device_ops {
  * @nr:		Device number on serdev bus.
  * @ctrl:	serdev controller managing this device.
  * @ops:	Device operations.
+ * @write_comp	Completion used by serdev_device_write() internally
+ * @write_lock	Lock to serialize access when writing data
  */
 struct serdev_device {
 	struct device dev;
 	int nr;
 	struct serdev_controller *ctrl;
 	const struct serdev_device_ops *ops;
+	struct completion write_comp;
+	struct mutex write_lock;
 };
 
 static inline struct serdev_device *to_serdev_device(struct device *d)
@@ -170,7 +174,7 @@ static inline void serdev_controller_write_wakeup(struct serdev_controller *ctrl
 	if (!serdev || !serdev->ops->write_wakeup)
 		return;
 
-	serdev->ops->write_wakeup(ctrl->serdev);
+	serdev->ops->write_wakeup(serdev);
 }
 
 static inline int serdev_controller_receive_buf(struct serdev_controller *ctrl,
@@ -182,7 +186,7 @@ static inline int serdev_controller_receive_buf(struct serdev_controller *ctrl,
 	if (!serdev || !serdev->ops->receive_buf)
 		return -EINVAL;
 
-	return serdev->ops->receive_buf(ctrl->serdev, data, count);
+	return serdev->ops->receive_buf(serdev, data, count);
 }
 
 #if IS_ENABLED(CONFIG_SERIAL_DEV_BUS)
@@ -194,7 +198,8 @@ void serdev_device_set_flow_control(struct serdev_device *, bool);
 void serdev_device_wait_until_sent(struct serdev_device *, long);
 int serdev_device_get_tiocm(struct serdev_device *);
 int serdev_device_set_tiocm(struct serdev_device *, int, int);
-int serdev_device_write_buf(struct serdev_device *, const unsigned char *, size_t);
+void serdev_device_write_wakeup(struct serdev_device *);
+int serdev_device_write(struct serdev_device *, const unsigned char *, size_t, unsigned long);
 void serdev_device_write_flush(struct serdev_device *);
 int serdev_device_write_room(struct serdev_device *);
 
@@ -240,7 +245,8 @@ static inline int serdev_device_set_tiocm(struct serdev_device *serdev, int set,
 {
 	return -ENOTSUPP;
 }
-static inline int serdev_device_write_buf(struct serdev_device *sdev, const unsigned char *buf, size_t count)
+static inline int serdev_device_write(struct serdev_device *sdev, const unsigned char *buf,
+				      size_t count, unsigned long timeout)
 {
 	return -ENODEV;
 }
@@ -306,4 +312,11 @@ static inline struct device *serdev_tty_port_register(struct tty_port *port,
 static inline void serdev_tty_port_unregister(struct tty_port *port) {}
 #endif /* CONFIG_SERIAL_DEV_CTRL_TTYPORT */
 
+static inline int serdev_device_write_buf(struct serdev_device *serdev,
+					  const unsigned char *data,
+					  size_t count)
+{
+	return serdev_device_write(serdev, data, count, 0);
+}
+
 #endif /*_LINUX_SERDEV_H */
diff --git a/include/linux/serial_core.h b/include/linux/serial_core.h
index 58484fb35cc8..64d892f1e5cd 100644
--- a/include/linux/serial_core.h
+++ b/include/linux/serial_core.h
@@ -247,6 +247,7 @@ struct uart_port {
 	unsigned char		suspended;
 	unsigned char		irq_wake;
 	unsigned char		unused[2];
+	const char		*name;			/* port name */
 	struct attribute_group	*attr_group;		/* port specific attributes */
 	const struct attribute_group **tty_groups;	/* all attributes (serial core use only) */
 	struct serial_rs485     rs485;
diff --git a/include/linux/tty.h b/include/linux/tty.h
index 1017e904c0a3..d07cd2105a6c 100644
--- a/include/linux/tty.h
+++ b/include/linux/tty.h
@@ -390,7 +390,6 @@ static inline bool tty_throttled(struct tty_struct *tty)
 }
 
 #ifdef CONFIG_TTY
-extern void console_init(void);
 extern void tty_kref_put(struct tty_struct *tty);
 extern struct pid *tty_get_pgrp(struct tty_struct *tty);
 extern void tty_vhangup_self(void);
@@ -402,8 +401,6 @@ extern struct tty_struct *get_current_tty(void);
 extern int __init tty_init(void);
 extern const char *tty_name(const struct tty_struct *tty);
 #else
-static inline void console_init(void)
-{ }
 static inline void tty_kref_put(struct tty_struct *tty)
 { }
 static inline struct pid *tty_get_pgrp(struct tty_struct *tty)
@@ -478,9 +475,13 @@ extern int tty_do_resize(struct tty_struct *tty, struct winsize *ws);
 extern int is_current_pgrp_orphaned(void);
 extern void tty_hangup(struct tty_struct *tty);
 extern void tty_vhangup(struct tty_struct *tty);
+extern void tty_vhangup_session(struct tty_struct *tty);
 extern int tty_hung_up_p(struct file *filp);
 extern void do_SAK(struct tty_struct *tty);
 extern void __do_SAK(struct tty_struct *tty);
+extern void tty_open_proc_set_tty(struct file *filp, struct tty_struct *tty);
+extern int tty_signal_session_leader(struct tty_struct *tty, int exit_session);
+extern void session_clear_tty(struct pid *session);
 extern void no_tty(void);
 extern void tty_buffer_free_all(struct tty_port *port);
 extern void tty_buffer_flush(struct tty_struct *tty, struct tty_ldisc *ld);
@@ -528,6 +529,8 @@ extern void tty_ldisc_flush(struct tty_struct *tty);
 extern long tty_ioctl(struct file *file, unsigned int cmd, unsigned long arg);
 extern int tty_mode_ioctl(struct tty_struct *tty, struct file *file,
 			unsigned int cmd, unsigned long arg);
+extern long tty_jobctrl_ioctl(struct tty_struct *tty, struct tty_struct *real_tty,
+			      struct file *file, unsigned int cmd, unsigned long arg);
 extern int tty_perform_flush(struct tty_struct *tty, unsigned long arg);
 extern void tty_default_fops(struct file_operations *fops);
 extern struct tty_struct *alloc_tty_struct(struct tty_driver *driver, int idx);
@@ -669,7 +672,11 @@ extern int tty_ldisc_receive_buf(struct tty_ldisc *ld, const unsigned char *p,
 
 /* n_tty.c */
 extern void n_tty_inherit_ops(struct tty_ldisc_ops *ops);
+#ifdef CONFIG_TTY
 extern void __init n_tty_init(void);
+#else
+static inline void n_tty_init(void) { }
+#endif
 
 /* tty_audit.c */
 #ifdef CONFIG_AUDIT
diff --git a/init/main.c b/init/main.c
index cc48053bb39f..f866510472d7 100644
--- a/init/main.c
+++ b/init/main.c
@@ -27,7 +27,7 @@
 #include <linux/initrd.h>
 #include <linux/bootmem.h>
 #include <linux/acpi.h>
-#include <linux/tty.h>
+#include <linux/console.h>
 #include <linux/nmi.h>
 #include <linux/percpu.h>
 #include <linux/kmod.h>
diff --git a/kernel/printk/braille.c b/kernel/printk/braille.c
index d5760c42f042..61d41ca41844 100644
--- a/kernel/printk/braille.c
+++ b/kernel/printk/braille.c
@@ -2,12 +2,13 @@
 
 #include <linux/kernel.h>
 #include <linux/console.h>
+#include <linux/errno.h>
 #include <linux/string.h>
 
 #include "console_cmdline.h"
 #include "braille.h"
 
-char *_braille_console_setup(char **str, char **brl_options)
+int _braille_console_setup(char **str, char **brl_options)
 {
 	if (!strncmp(*str, "brl,", 4)) {
 		*brl_options = "";
@@ -15,14 +16,14 @@ char *_braille_console_setup(char **str, char **brl_options)
 	} else if (!strncmp(*str, "brl=", 4)) {
 		*brl_options = *str + 4;
 		*str = strchr(*brl_options, ',');
-		if (!*str)
+		if (!*str) {
 			pr_err("need port name after brl=\n");
-		else
-			*((*str)++) = 0;
-	} else
-		return NULL;
+			return -EINVAL;
+		}
+		*((*str)++) = 0;
+	}
 
-	return *str;
+	return 0;
 }
 
 int
diff --git a/kernel/printk/braille.h b/kernel/printk/braille.h
index 769d771145c8..749a6756843a 100644
--- a/kernel/printk/braille.h
+++ b/kernel/printk/braille.h
@@ -9,7 +9,14 @@ braille_set_options(struct console_cmdline *c, char *brl_options)
 	c->brl_options = brl_options;
 }
 
-char *
+/*
+ * Setup console according to braille options.
+ * Return -EINVAL on syntax error, 0 on success (or no braille option was
+ * actually given).
+ * Modifies str to point to the serial options
+ * Sets brl_options to the parsed braille options.
+ */
+int
 _braille_console_setup(char **str, char **brl_options);
 
 int
@@ -25,10 +32,10 @@ braille_set_options(struct console_cmdline *c, char *brl_options)
 {
 }
 
-static inline char *
+static inline int
 _braille_console_setup(char **str, char **brl_options)
 {
-	return NULL;
+	return 0;
 }
 
 static inline int
diff --git a/kernel/printk/printk.c b/kernel/printk/printk.c
index fb2d1591f671..a1aecf44ab07 100644
--- a/kernel/printk/printk.c
+++ b/kernel/printk/printk.c
@@ -2641,6 +2641,30 @@ int unregister_console(struct console *console)
 }
 EXPORT_SYMBOL(unregister_console);
 
+/*
+ * Initialize the console device. This is called *early*, so
+ * we can't necessarily depend on lots of kernel help here.
+ * Just do some early initializations, and do the complex setup
+ * later.
+ */
+void __init console_init(void)
+{
+	initcall_t *call;
+
+	/* Setup the default TTY line discipline. */
+	n_tty_init();
+
+	/*
+	 * set up the console device so that later boot sequences can
+	 * inform about problems etc..
+	 */
+	call = __con_initcall_start;
+	while (call < __con_initcall_end) {
+		(*call)();
+		call++;
+	}
+}
+
 /*
  * Some boot consoles access data that is in the init section and which will
  * be discarded after the initcalls have been run. To make sure that no code