gma500: begin adding CDV specific code
A lot of the intel_display stuff is duplicated, but we will add it first, clean it up and then investigate the best way to merge stuff. This first block integrates the various basic chunks of the CDV display setup. Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit is contained in:
parent
4bc5925315
commit
93b68b6773
|
@ -24,7 +24,10 @@ psb_gfx-y += gem_glue.o \
|
|||
psb_device.o \
|
||||
mid_bios.o
|
||||
|
||||
psb_gfx-$(CONFIG_DRM_PSB_CDV) += cdv_device.o
|
||||
psb_gfx-$(CONFIG_DRM_PSB_CDV) += cdv_device.o \
|
||||
cdv_intel_display.o \
|
||||
cdv_intel_crt.o \
|
||||
cdv_intel_lvds.o
|
||||
|
||||
psb_gfx-$(CONFIG_DRM_PSB_MRST) += mrst_device.o \
|
||||
mrst_crtc.o \
|
||||
|
|
|
@ -25,13 +25,42 @@
|
|||
#include "psb_reg.h"
|
||||
#include "psb_intel_reg.h"
|
||||
#include "intel_bios.h"
|
||||
#include "cdv_device.h"
|
||||
|
||||
#define VGA_SR_INDEX 0x3c4
|
||||
#define VGA_SR_DATA 0x3c5
|
||||
|
||||
/* FIXME: should check if we are the active VGA device ?? */
|
||||
static void cdv_disable_vga(struct drm_device *dev)
|
||||
{
|
||||
u8 sr1;
|
||||
u32 vga_reg;
|
||||
|
||||
vga_reg = VGACNTRL;
|
||||
|
||||
outb(1, VGA_SR_INDEX);
|
||||
sr1 = inb(VGA_SR_DATA);
|
||||
outb(sr1 | 1<<5, VGA_SR_DATA);
|
||||
udelay(300);
|
||||
|
||||
REG_WRITE(vga_reg, VGA_DISP_DISABLE);
|
||||
REG_READ(vga_reg);
|
||||
}
|
||||
|
||||
static int cdv_output_init(struct drm_device *dev)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
psb_intel_lvds_init(dev, &dev_priv->mode_dev);
|
||||
psb_intel_sdvo_init(dev, SDVOB);
|
||||
cdv_disable_vga(dev);
|
||||
|
||||
cdv_intel_crt_init(dev, &dev_priv->mode_dev);
|
||||
cdv_intel_lvds_init(dev, &dev_priv->mode_dev);
|
||||
|
||||
/* These bits indicate HDMI not SDVO on CDV, but we don't yet support
|
||||
the HDMI interface */
|
||||
if (REG_READ(SDVOB) & SDVO_DETECTED)
|
||||
DRM_ERROR("HDMI not supported yet\n");
|
||||
if (REG_READ(SDVOC) & SDVO_DETECTED)
|
||||
DRM_ERROR("HDMI not supported yet\n");
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
@ -148,19 +177,70 @@ static int cdv_backlight_init(struct drm_device *dev)
|
|||
#endif
|
||||
|
||||
/*
|
||||
* Provide the Poulsbo specific chip logic and low level methods
|
||||
* Provide the Cedarview specific chip logic and low level methods
|
||||
* for power management
|
||||
*
|
||||
* FIXME: we need to implement the apm/ospm base management bits
|
||||
* for this and the MID devices.
|
||||
*/
|
||||
|
||||
static inline u32 CDV_MSG_READ32(uint port, uint offset)
|
||||
{
|
||||
int mcr = (0x10<<24) | (port << 16) | (offset << 8);
|
||||
uint32_t ret_val = 0;
|
||||
struct pci_dev *pci_root = pci_get_bus_and_slot (0, 0);
|
||||
pci_write_config_dword (pci_root, 0xD0, mcr);
|
||||
pci_read_config_dword (pci_root, 0xD4, &ret_val);
|
||||
pci_dev_put(pci_root);
|
||||
return ret_val;
|
||||
}
|
||||
|
||||
static inline void CDV_MSG_WRITE32(uint port, uint offset, u32 value)
|
||||
{
|
||||
int mcr = (0x11<<24) | (port << 16) | (offset << 8) | 0xF0;
|
||||
struct pci_dev *pci_root = pci_get_bus_and_slot (0, 0);
|
||||
pci_write_config_dword (pci_root, 0xD4, value);
|
||||
pci_write_config_dword (pci_root, 0xD0, mcr);
|
||||
pci_dev_put(pci_root);
|
||||
}
|
||||
|
||||
#define PSB_APM_CMD 0x0
|
||||
#define PSB_APM_STS 0x04
|
||||
#define PSB_PM_SSC 0x20
|
||||
#define PSB_PM_SSS 0x30
|
||||
#define PSB_PWRGT_GFX_MASK 0x3
|
||||
#define CDV_PWRGT_DISPLAY_CNTR 0x000fc00c
|
||||
#define CDV_PWRGT_DISPLAY_STS 0x000fc00c
|
||||
|
||||
static void cdv_init_pm(struct drm_device *dev)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
u32 pwr_cnt;
|
||||
int i;
|
||||
|
||||
u32 gating = PSB_RSGX32(PSB_CR_CLKGATECTL);
|
||||
gating &= ~3; /* Disable 2D clock gating */
|
||||
gating |= 1;
|
||||
PSB_WSGX32(gating, PSB_CR_CLKGATECTL);
|
||||
PSB_RSGX32(PSB_CR_CLKGATECTL);
|
||||
dev_priv->apm_base = CDV_MSG_READ32(PSB_PUNIT_PORT, PSB_APMBA) & 0xFFFF;
|
||||
dev_priv->ospm_base = CDV_MSG_READ32(PSB_PUNIT_PORT, PSB_OSPMBA) & 0xFFFF;
|
||||
|
||||
/* Force power on for now */
|
||||
pwr_cnt = inl(dev_priv->apm_base + PSB_APM_CMD);
|
||||
pwr_cnt &= ~PSB_PWRGT_GFX_MASK;
|
||||
|
||||
outl(pwr_cnt, dev_priv->apm_base + PSB_APM_CMD);
|
||||
for (i = 0; i < 5; i++) {
|
||||
u32 pwr_sts = inl(dev_priv->apm_base + PSB_APM_STS);
|
||||
if ((pwr_sts & PSB_PWRGT_GFX_MASK) == 0)
|
||||
break;
|
||||
udelay(10);
|
||||
}
|
||||
pwr_cnt = inl(dev_priv->ospm_base + PSB_PM_SSC);
|
||||
pwr_cnt &= ~CDV_PWRGT_DISPLAY_CNTR;
|
||||
outl(pwr_cnt, dev_priv->ospm_base + PSB_PM_SSC);
|
||||
for (i = 0; i < 5; i++) {
|
||||
u32 pwr_sts = inl(dev_priv->ospm_base + PSB_PM_SSS);
|
||||
if ((pwr_sts & CDV_PWRGT_DISPLAY_STS) == 0)
|
||||
break;
|
||||
udelay(10);
|
||||
}
|
||||
}
|
||||
|
||||
/**
|
||||
|
@ -169,34 +249,11 @@ static void cdv_init_pm(struct drm_device *dev)
|
|||
*
|
||||
* Save the state we need in order to be able to restore the interface
|
||||
* upon resume from suspend
|
||||
*
|
||||
* FIXME: review
|
||||
*/
|
||||
static int cdv_save_display_registers(struct drm_device *dev)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
struct drm_crtc *crtc;
|
||||
struct drm_connector *connector;
|
||||
|
||||
/* Display arbitration control + watermarks */
|
||||
dev_priv->saveDSPARB = PSB_RVDC32(DSPARB);
|
||||
dev_priv->saveDSPFW1 = PSB_RVDC32(DSPFW1);
|
||||
dev_priv->saveDSPFW2 = PSB_RVDC32(DSPFW2);
|
||||
dev_priv->saveDSPFW3 = PSB_RVDC32(DSPFW3);
|
||||
dev_priv->saveDSPFW4 = PSB_RVDC32(DSPFW4);
|
||||
dev_priv->saveDSPFW5 = PSB_RVDC32(DSPFW5);
|
||||
dev_priv->saveDSPFW6 = PSB_RVDC32(DSPFW6);
|
||||
dev_priv->saveCHICKENBIT = PSB_RVDC32(DSPCHICKENBIT);
|
||||
|
||||
/* Save crtc and output state */
|
||||
mutex_lock(&dev->mode_config.mutex);
|
||||
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head) {
|
||||
if (drm_helper_crtc_in_use(crtc))
|
||||
crtc->funcs->save(crtc);
|
||||
}
|
||||
|
||||
list_for_each_entry(connector, &dev->mode_config.connector_list, head)
|
||||
connector->funcs->save(connector);
|
||||
|
||||
mutex_unlock(&dev->mode_config.mutex);
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
@ -205,67 +262,11 @@ static int cdv_save_display_registers(struct drm_device *dev)
|
|||
* @dev: our DRM device
|
||||
*
|
||||
* Restore register state that was lost during suspend and resume.
|
||||
*
|
||||
* FIXME: review
|
||||
*/
|
||||
static int cdv_restore_display_registers(struct drm_device *dev)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
struct drm_crtc *crtc;
|
||||
struct drm_connector *connector;
|
||||
int pp_stat;
|
||||
|
||||
/* Display arbitration + watermarks */
|
||||
PSB_WVDC32(dev_priv->saveDSPARB, DSPARB);
|
||||
PSB_WVDC32(dev_priv->saveDSPFW1, DSPFW1);
|
||||
PSB_WVDC32(dev_priv->saveDSPFW2, DSPFW2);
|
||||
PSB_WVDC32(dev_priv->saveDSPFW3, DSPFW3);
|
||||
PSB_WVDC32(dev_priv->saveDSPFW4, DSPFW4);
|
||||
PSB_WVDC32(dev_priv->saveDSPFW5, DSPFW5);
|
||||
PSB_WVDC32(dev_priv->saveDSPFW6, DSPFW6);
|
||||
PSB_WVDC32(dev_priv->saveCHICKENBIT, DSPCHICKENBIT);
|
||||
|
||||
/*make sure VGA plane is off. it initializes to on after reset!*/
|
||||
PSB_WVDC32(0x80000000, VGACNTRL);
|
||||
|
||||
mutex_lock(&dev->mode_config.mutex);
|
||||
list_for_each_entry(crtc, &dev->mode_config.crtc_list, head)
|
||||
if (drm_helper_crtc_in_use(crtc))
|
||||
crtc->funcs->restore(crtc);
|
||||
|
||||
list_for_each_entry(connector, &dev->mode_config.connector_list, head)
|
||||
connector->funcs->restore(connector);
|
||||
|
||||
mutex_unlock(&dev->mode_config.mutex);
|
||||
|
||||
if (dev_priv->iLVDS_enable) {
|
||||
/*shutdown the panel*/
|
||||
PSB_WVDC32(0, PP_CONTROL);
|
||||
do {
|
||||
pp_stat = PSB_RVDC32(PP_STATUS);
|
||||
} while (pp_stat & 0x80000000);
|
||||
|
||||
/* Turn off the plane */
|
||||
PSB_WVDC32(0x58000000, DSPACNTR);
|
||||
PSB_WVDC32(0, DSPASURF);/*trigger the plane disable*/
|
||||
/* Wait ~4 ticks */
|
||||
msleep(4);
|
||||
/* Turn off pipe */
|
||||
PSB_WVDC32(0x0, PIPEACONF);
|
||||
/* Wait ~8 ticks */
|
||||
msleep(8);
|
||||
|
||||
/* Turn off PLLs */
|
||||
PSB_WVDC32(0, MRST_DPLL_A);
|
||||
} else {
|
||||
PSB_WVDC32(DPI_SHUT_DOWN, DPI_CONTROL_REG);
|
||||
PSB_WVDC32(0x0, PIPEACONF);
|
||||
PSB_WVDC32(0x2faf0000, BLC_PWM_CTL);
|
||||
while (REG_READ(0x70008) & 0x40000000)
|
||||
cpu_relax();
|
||||
while ((PSB_RVDC32(GEN_FIFO_STAT_REG) & DPI_FIFO_EMPTY)
|
||||
!= DPI_FIFO_EMPTY)
|
||||
cpu_relax();
|
||||
PSB_WVDC32(0, DEVICE_READY_REG);
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
@ -286,9 +287,6 @@ static void cdv_get_core_freq(struct drm_device *dev)
|
|||
struct pci_dev *pci_root = pci_get_bus_and_slot(0, 0);
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
|
||||
/*pci_write_config_dword(pci_root, 0xD4, 0x00C32004);*/
|
||||
/*pci_write_config_dword(pci_root, 0xD0, 0xE0033000);*/
|
||||
|
||||
pci_write_config_dword(pci_root, 0xD0, 0xD0050300);
|
||||
pci_read_config_dword(pci_root, 0xD4, &clock);
|
||||
pci_dev_put(pci_root);
|
||||
|
@ -326,7 +324,7 @@ static int cdv_chip_setup(struct drm_device *dev)
|
|||
return 0;
|
||||
}
|
||||
|
||||
/* CDV is much like Poulsbo but has MID like SGX offsets */
|
||||
/* CDV is much like Poulsbo but has MID like SGX offsets and PM */
|
||||
|
||||
const struct psb_ops cdv_chip_ops = {
|
||||
.name = "Cedartrail",
|
||||
|
@ -335,8 +333,8 @@ const struct psb_ops cdv_chip_ops = {
|
|||
.sgx_offset = MRST_SGX_OFFSET,
|
||||
.chip_setup = cdv_chip_setup,
|
||||
|
||||
.crtc_helper = &psb_intel_helper_funcs,
|
||||
.crtc_funcs = &psb_intel_crtc_funcs,
|
||||
.crtc_helper = &cdv_intel_helper_funcs,
|
||||
.crtc_funcs = &cdv_intel_crtc_funcs,
|
||||
|
||||
.output_init = cdv_output_init,
|
||||
|
||||
|
@ -350,4 +348,3 @@ const struct psb_ops cdv_chip_ops = {
|
|||
.power_down = cdv_power_down,
|
||||
.power_up = cdv_power_up,
|
||||
};
|
||||
|
||||
|
|
1513
drivers/staging/gma500/cdv_intel_display.c
Normal file
1513
drivers/staging/gma500/cdv_intel_display.c
Normal file
File diff suppressed because it is too large
Load diff
718
drivers/staging/gma500/cdv_intel_lvds.c
Normal file
718
drivers/staging/gma500/cdv_intel_lvds.c
Normal file
|
@ -0,0 +1,718 @@
|
|||
/*
|
||||
* Copyright © 2006-2011 Intel Corporation
|
||||
*
|
||||
* This program is free software; you can redistribute it and/or modify it
|
||||
* under the terms and conditions of the GNU General Public License,
|
||||
* version 2, as published by the Free Software Foundation.
|
||||
*
|
||||
* This program is distributed in the hope it will be useful, but WITHOUT
|
||||
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
|
||||
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
|
||||
* more details.
|
||||
*
|
||||
* You should have received a copy of the GNU General Public License along with
|
||||
* this program; if not, write to the Free Software Foundation, Inc.,
|
||||
* 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
|
||||
*
|
||||
* Authors:
|
||||
* Eric Anholt <eric@anholt.net>
|
||||
* Dave Airlie <airlied@linux.ie>
|
||||
* Jesse Barnes <jesse.barnes@intel.com>
|
||||
*/
|
||||
|
||||
#include <linux/i2c.h>
|
||||
#include <linux/dmi.h>
|
||||
#include <drm/drmP.h>
|
||||
|
||||
#include "intel_bios.h"
|
||||
#include "psb_drv.h"
|
||||
#include "psb_intel_drv.h"
|
||||
#include "psb_intel_reg.h"
|
||||
#include "power.h"
|
||||
#include <linux/pm_runtime.h>
|
||||
#include "cdv_device.h"
|
||||
|
||||
/**
|
||||
* LVDS I2C backlight control macros
|
||||
*/
|
||||
#define BRIGHTNESS_MAX_LEVEL 100
|
||||
#define BRIGHTNESS_MASK 0xFF
|
||||
#define BLC_I2C_TYPE 0x01
|
||||
#define BLC_PWM_TYPT 0x02
|
||||
|
||||
#define BLC_POLARITY_NORMAL 0
|
||||
#define BLC_POLARITY_INVERSE 1
|
||||
|
||||
#define PSB_BLC_MAX_PWM_REG_FREQ (0xFFFE)
|
||||
#define PSB_BLC_MIN_PWM_REG_FREQ (0x2)
|
||||
#define PSB_BLC_PWM_PRECISION_FACTOR (10)
|
||||
#define PSB_BACKLIGHT_PWM_CTL_SHIFT (16)
|
||||
#define PSB_BACKLIGHT_PWM_POLARITY_BIT_CLEAR (0xFFFE)
|
||||
|
||||
struct cdv_intel_lvds_priv {
|
||||
/**
|
||||
* Saved LVDO output states
|
||||
*/
|
||||
uint32_t savePP_ON;
|
||||
uint32_t savePP_OFF;
|
||||
uint32_t saveLVDS;
|
||||
uint32_t savePP_CONTROL;
|
||||
uint32_t savePP_CYCLE;
|
||||
uint32_t savePFIT_CONTROL;
|
||||
uint32_t savePFIT_PGM_RATIOS;
|
||||
uint32_t saveBLC_PWM_CTL;
|
||||
};
|
||||
|
||||
/*
|
||||
* Returns the maximum level of the backlight duty cycle field.
|
||||
*/
|
||||
static u32 cdv_intel_lvds_get_max_backlight(struct drm_device *dev)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
u32 retval;
|
||||
|
||||
if (gma_power_begin(dev, false)) {
|
||||
retval = ((REG_READ(BLC_PWM_CTL) &
|
||||
BACKLIGHT_MODULATION_FREQ_MASK) >>
|
||||
BACKLIGHT_MODULATION_FREQ_SHIFT) * 2;
|
||||
|
||||
gma_power_end(dev);
|
||||
} else
|
||||
retval = ((dev_priv->saveBLC_PWM_CTL &
|
||||
BACKLIGHT_MODULATION_FREQ_MASK) >>
|
||||
BACKLIGHT_MODULATION_FREQ_SHIFT) * 2;
|
||||
|
||||
return retval;
|
||||
}
|
||||
|
||||
/*
|
||||
* Set LVDS backlight level by I2C command
|
||||
*/
|
||||
static int cdv_lvds_i2c_set_brightness(struct drm_device *dev,
|
||||
unsigned int level)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
struct psb_intel_i2c_chan *lvds_i2c_bus = dev_priv->lvds_i2c_bus;
|
||||
u8 out_buf[2];
|
||||
unsigned int blc_i2c_brightness;
|
||||
|
||||
struct i2c_msg msgs[] = {
|
||||
{
|
||||
.addr = lvds_i2c_bus->slave_addr,
|
||||
.flags = 0,
|
||||
.len = 2,
|
||||
.buf = out_buf,
|
||||
}
|
||||
};
|
||||
|
||||
blc_i2c_brightness = BRIGHTNESS_MASK & ((unsigned int)level *
|
||||
BRIGHTNESS_MASK /
|
||||
BRIGHTNESS_MAX_LEVEL);
|
||||
|
||||
if (dev_priv->lvds_bl->pol == BLC_POLARITY_INVERSE)
|
||||
blc_i2c_brightness = BRIGHTNESS_MASK - blc_i2c_brightness;
|
||||
|
||||
out_buf[0] = dev_priv->lvds_bl->brightnesscmd;
|
||||
out_buf[1] = (u8)blc_i2c_brightness;
|
||||
|
||||
if (i2c_transfer(&lvds_i2c_bus->adapter, msgs, 1) == 1)
|
||||
return 0;
|
||||
|
||||
DRM_ERROR("I2C transfer error\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
|
||||
static int cdv_lvds_pwm_set_brightness(struct drm_device *dev, int level)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
|
||||
u32 max_pwm_blc;
|
||||
u32 blc_pwm_duty_cycle;
|
||||
|
||||
max_pwm_blc = cdv_intel_lvds_get_max_backlight(dev);
|
||||
|
||||
/*BLC_PWM_CTL Should be initiated while backlight device init*/
|
||||
BUG_ON((max_pwm_blc & PSB_BLC_MAX_PWM_REG_FREQ) == 0);
|
||||
|
||||
blc_pwm_duty_cycle = level * max_pwm_blc / BRIGHTNESS_MAX_LEVEL;
|
||||
|
||||
if (dev_priv->lvds_bl->pol == BLC_POLARITY_INVERSE)
|
||||
blc_pwm_duty_cycle = max_pwm_blc - blc_pwm_duty_cycle;
|
||||
|
||||
blc_pwm_duty_cycle &= PSB_BACKLIGHT_PWM_POLARITY_BIT_CLEAR;
|
||||
REG_WRITE(BLC_PWM_CTL,
|
||||
(max_pwm_blc << PSB_BACKLIGHT_PWM_CTL_SHIFT) |
|
||||
(blc_pwm_duty_cycle));
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/*
|
||||
* Set LVDS backlight level either by I2C or PWM
|
||||
*/
|
||||
void cdv_intel_lvds_set_brightness(struct drm_device *dev, int level)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
|
||||
if (!dev_priv->lvds_bl) {
|
||||
DRM_ERROR("NO LVDS Backlight Info\n");
|
||||
return;
|
||||
}
|
||||
|
||||
if (dev_priv->lvds_bl->type == BLC_I2C_TYPE)
|
||||
cdv_lvds_i2c_set_brightness(dev, level);
|
||||
else
|
||||
cdv_lvds_pwm_set_brightness(dev, level);
|
||||
}
|
||||
|
||||
/**
|
||||
* Sets the backlight level.
|
||||
*
|
||||
* level backlight level, from 0 to cdv_intel_lvds_get_max_backlight().
|
||||
*/
|
||||
static void cdv_intel_lvds_set_backlight(struct drm_device *dev, int level)
|
||||
{
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
u32 blc_pwm_ctl;
|
||||
|
||||
if (gma_power_begin(dev, false)) {
|
||||
blc_pwm_ctl =
|
||||
REG_READ(BLC_PWM_CTL) & ~BACKLIGHT_DUTY_CYCLE_MASK;
|
||||
REG_WRITE(BLC_PWM_CTL,
|
||||
(blc_pwm_ctl |
|
||||
(level << BACKLIGHT_DUTY_CYCLE_SHIFT)));
|
||||
gma_power_end(dev);
|
||||
} else {
|
||||
blc_pwm_ctl = dev_priv->saveBLC_PWM_CTL &
|
||||
~BACKLIGHT_DUTY_CYCLE_MASK;
|
||||
dev_priv->saveBLC_PWM_CTL = (blc_pwm_ctl |
|
||||
(level << BACKLIGHT_DUTY_CYCLE_SHIFT));
|
||||
}
|
||||
}
|
||||
|
||||
/**
|
||||
* Sets the power state for the panel.
|
||||
*/
|
||||
static void cdv_intel_lvds_set_power(struct drm_device *dev,
|
||||
struct psb_intel_output *output, bool on)
|
||||
{
|
||||
u32 pp_status;
|
||||
|
||||
if (!gma_power_begin(dev, true))
|
||||
return;
|
||||
|
||||
if (on) {
|
||||
REG_WRITE(PP_CONTROL, REG_READ(PP_CONTROL) |
|
||||
POWER_TARGET_ON);
|
||||
do {
|
||||
pp_status = REG_READ(PP_STATUS);
|
||||
} while ((pp_status & PP_ON) == 0);
|
||||
|
||||
cdv_intel_lvds_set_backlight(dev,
|
||||
output->
|
||||
mode_dev->backlight_duty_cycle);
|
||||
} else {
|
||||
cdv_intel_lvds_set_backlight(dev, 0);
|
||||
|
||||
REG_WRITE(PP_CONTROL, REG_READ(PP_CONTROL) &
|
||||
~POWER_TARGET_ON);
|
||||
do {
|
||||
pp_status = REG_READ(PP_STATUS);
|
||||
} while (pp_status & PP_ON);
|
||||
}
|
||||
gma_power_end(dev);
|
||||
}
|
||||
|
||||
static void cdv_intel_lvds_encoder_dpms(struct drm_encoder *encoder, int mode)
|
||||
{
|
||||
struct drm_device *dev = encoder->dev;
|
||||
struct psb_intel_output *output = enc_to_psb_intel_output(encoder);
|
||||
if (mode == DRM_MODE_DPMS_ON)
|
||||
cdv_intel_lvds_set_power(dev, output, true);
|
||||
else
|
||||
cdv_intel_lvds_set_power(dev, output, false);
|
||||
/* XXX: We never power down the LVDS pairs. */
|
||||
}
|
||||
|
||||
static void cdv_intel_lvds_save(struct drm_connector *connector)
|
||||
{
|
||||
}
|
||||
|
||||
static void cdv_intel_lvds_restore(struct drm_connector *connector)
|
||||
{
|
||||
}
|
||||
|
||||
int cdv_intel_lvds_mode_valid(struct drm_connector *connector,
|
||||
struct drm_display_mode *mode)
|
||||
{
|
||||
struct psb_intel_output *psb_intel_output =
|
||||
to_psb_intel_output(connector);
|
||||
struct drm_display_mode *fixed_mode =
|
||||
psb_intel_output->mode_dev->panel_fixed_mode;
|
||||
|
||||
/* just in case */
|
||||
if (mode->flags & DRM_MODE_FLAG_DBLSCAN)
|
||||
return MODE_NO_DBLESCAN;
|
||||
|
||||
/* just in case */
|
||||
if (mode->flags & DRM_MODE_FLAG_INTERLACE)
|
||||
return MODE_NO_INTERLACE;
|
||||
|
||||
if (fixed_mode) {
|
||||
if (mode->hdisplay > fixed_mode->hdisplay)
|
||||
return MODE_PANEL;
|
||||
if (mode->vdisplay > fixed_mode->vdisplay)
|
||||
return MODE_PANEL;
|
||||
}
|
||||
return MODE_OK;
|
||||
}
|
||||
|
||||
bool cdv_intel_lvds_mode_fixup(struct drm_encoder *encoder,
|
||||
struct drm_display_mode *mode,
|
||||
struct drm_display_mode *adjusted_mode)
|
||||
{
|
||||
struct psb_intel_mode_device *mode_dev =
|
||||
enc_to_psb_intel_output(encoder)->mode_dev;
|
||||
struct drm_device *dev = encoder->dev;
|
||||
struct drm_encoder *tmp_encoder;
|
||||
struct drm_display_mode *panel_fixed_mode = mode_dev->panel_fixed_mode;
|
||||
|
||||
/* Should never happen!! */
|
||||
list_for_each_entry(tmp_encoder, &dev->mode_config.encoder_list,
|
||||
head) {
|
||||
if (tmp_encoder != encoder
|
||||
&& tmp_encoder->crtc == encoder->crtc) {
|
||||
printk(KERN_ERR "Can't enable LVDS and another "
|
||||
"encoder on the same pipe\n");
|
||||
return false;
|
||||
}
|
||||
}
|
||||
|
||||
/*
|
||||
* If we have timings from the BIOS for the panel, put them in
|
||||
* to the adjusted mode. The CRTC will be set up for this mode,
|
||||
* with the panel scaling set up to source from the H/VDisplay
|
||||
* of the original mode.
|
||||
*/
|
||||
if (panel_fixed_mode != NULL) {
|
||||
adjusted_mode->hdisplay = panel_fixed_mode->hdisplay;
|
||||
adjusted_mode->hsync_start = panel_fixed_mode->hsync_start;
|
||||
adjusted_mode->hsync_end = panel_fixed_mode->hsync_end;
|
||||
adjusted_mode->htotal = panel_fixed_mode->htotal;
|
||||
adjusted_mode->vdisplay = panel_fixed_mode->vdisplay;
|
||||
adjusted_mode->vsync_start = panel_fixed_mode->vsync_start;
|
||||
adjusted_mode->vsync_end = panel_fixed_mode->vsync_end;
|
||||
adjusted_mode->vtotal = panel_fixed_mode->vtotal;
|
||||
adjusted_mode->clock = panel_fixed_mode->clock;
|
||||
drm_mode_set_crtcinfo(adjusted_mode,
|
||||
CRTC_INTERLACE_HALVE_V);
|
||||
}
|
||||
|
||||
/*
|
||||
* XXX: It would be nice to support lower refresh rates on the
|
||||
* panels to reduce power consumption, and perhaps match the
|
||||
* user's requested refresh rate.
|
||||
*/
|
||||
|
||||
return true;
|
||||
}
|
||||
|
||||
static void cdv_intel_lvds_prepare(struct drm_encoder *encoder)
|
||||
{
|
||||
struct drm_device *dev = encoder->dev;
|
||||
struct psb_intel_output *output = enc_to_psb_intel_output(encoder);
|
||||
struct psb_intel_mode_device *mode_dev = output->mode_dev;
|
||||
|
||||
if (!gma_power_begin(dev, true))
|
||||
return;
|
||||
|
||||
mode_dev->saveBLC_PWM_CTL = REG_READ(BLC_PWM_CTL);
|
||||
mode_dev->backlight_duty_cycle = (mode_dev->saveBLC_PWM_CTL &
|
||||
BACKLIGHT_DUTY_CYCLE_MASK);
|
||||
|
||||
cdv_intel_lvds_set_power(dev, output, false);
|
||||
|
||||
gma_power_end(dev);
|
||||
}
|
||||
|
||||
static void cdv_intel_lvds_commit(struct drm_encoder *encoder)
|
||||
{
|
||||
struct drm_device *dev = encoder->dev;
|
||||
struct psb_intel_output *output = enc_to_psb_intel_output(encoder);
|
||||
struct psb_intel_mode_device *mode_dev = output->mode_dev;
|
||||
|
||||
if (mode_dev->backlight_duty_cycle == 0)
|
||||
mode_dev->backlight_duty_cycle =
|
||||
cdv_intel_lvds_get_max_backlight(dev);
|
||||
|
||||
cdv_intel_lvds_set_power(dev, output, true);
|
||||
}
|
||||
|
||||
static void cdv_intel_lvds_mode_set(struct drm_encoder *encoder,
|
||||
struct drm_display_mode *mode,
|
||||
struct drm_display_mode *adjusted_mode)
|
||||
{
|
||||
struct psb_intel_mode_device *mode_dev =
|
||||
enc_to_psb_intel_output(encoder)->mode_dev;
|
||||
struct drm_device *dev = encoder->dev;
|
||||
u32 pfit_control;
|
||||
|
||||
/*
|
||||
* The LVDS pin pair will already have been turned on in the
|
||||
* cdv_intel_crtc_mode_set since it has a large impact on the DPLL
|
||||
* settings.
|
||||
*/
|
||||
|
||||
/*
|
||||
* Enable automatic panel scaling so that non-native modes fill the
|
||||
* screen. Should be enabled before the pipe is enabled, according to
|
||||
* register description and PRM.
|
||||
*/
|
||||
if (mode->hdisplay != adjusted_mode->hdisplay ||
|
||||
mode->vdisplay != adjusted_mode->vdisplay)
|
||||
pfit_control = (PFIT_ENABLE | VERT_AUTO_SCALE |
|
||||
HORIZ_AUTO_SCALE | VERT_INTERP_BILINEAR |
|
||||
HORIZ_INTERP_BILINEAR);
|
||||
else
|
||||
pfit_control = 0;
|
||||
|
||||
if (mode_dev->panel_wants_dither)
|
||||
pfit_control |= PANEL_8TO6_DITHER_ENABLE;
|
||||
|
||||
REG_WRITE(PFIT_CONTROL, pfit_control);
|
||||
}
|
||||
|
||||
/**
|
||||
* Detect the LVDS connection.
|
||||
*
|
||||
* This always returns CONNECTOR_STATUS_CONNECTED.
|
||||
* This connector should only have
|
||||
* been set up if the LVDS was actually connected anyway.
|
||||
*/
|
||||
static enum drm_connector_status cdv_intel_lvds_detect(struct drm_connector *connector, bool force)
|
||||
{
|
||||
return connector_status_connected;
|
||||
}
|
||||
|
||||
/**
|
||||
* Return the list of DDC modes if available, or the BIOS fixed mode otherwise.
|
||||
*/
|
||||
static int cdv_intel_lvds_get_modes(struct drm_connector *connector)
|
||||
{
|
||||
struct drm_device *dev = connector->dev;
|
||||
struct psb_intel_output *psb_intel_output =
|
||||
to_psb_intel_output(connector);
|
||||
struct psb_intel_mode_device *mode_dev =
|
||||
psb_intel_output->mode_dev;
|
||||
int ret;
|
||||
|
||||
ret = psb_intel_ddc_get_modes(psb_intel_output);
|
||||
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
/* Didn't get an EDID, so
|
||||
* Set wide sync ranges so we get all modes
|
||||
* handed to valid_mode for checking
|
||||
*/
|
||||
connector->display_info.min_vfreq = 0;
|
||||
connector->display_info.max_vfreq = 200;
|
||||
connector->display_info.min_hfreq = 0;
|
||||
connector->display_info.max_hfreq = 200;
|
||||
if (mode_dev->panel_fixed_mode != NULL) {
|
||||
struct drm_display_mode *mode =
|
||||
drm_mode_duplicate(dev, mode_dev->panel_fixed_mode);
|
||||
drm_mode_probed_add(connector, mode);
|
||||
return 1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
/**
|
||||
* cdv_intel_lvds_destroy - unregister and free LVDS structures
|
||||
* @connector: connector to free
|
||||
*
|
||||
* Unregister the DDC bus for this connector then free the driver private
|
||||
* structure.
|
||||
*/
|
||||
void cdv_intel_lvds_destroy(struct drm_connector *connector)
|
||||
{
|
||||
struct psb_intel_output *psb_intel_output =
|
||||
to_psb_intel_output(connector);
|
||||
|
||||
if (psb_intel_output->ddc_bus)
|
||||
psb_intel_i2c_destroy(psb_intel_output->ddc_bus);
|
||||
drm_sysfs_connector_remove(connector);
|
||||
drm_connector_cleanup(connector);
|
||||
kfree(connector);
|
||||
}
|
||||
|
||||
int cdv_intel_lvds_set_property(struct drm_connector *connector,
|
||||
struct drm_property *property,
|
||||
uint64_t value)
|
||||
{
|
||||
struct drm_encoder *encoder = connector->encoder;
|
||||
|
||||
if (!strcmp(property->name, "scaling mode") && encoder) {
|
||||
struct psb_intel_crtc *crtc =
|
||||
to_psb_intel_crtc(encoder->crtc);
|
||||
uint64_t curValue;
|
||||
|
||||
if (!crtc)
|
||||
return -1;
|
||||
|
||||
switch (value) {
|
||||
case DRM_MODE_SCALE_FULLSCREEN:
|
||||
break;
|
||||
case DRM_MODE_SCALE_NO_SCALE:
|
||||
break;
|
||||
case DRM_MODE_SCALE_ASPECT:
|
||||
break;
|
||||
default:
|
||||
return -1;
|
||||
}
|
||||
|
||||
if (drm_connector_property_get_value(connector,
|
||||
property,
|
||||
&curValue))
|
||||
return -1;
|
||||
|
||||
if (curValue == value)
|
||||
return 0;
|
||||
|
||||
if (drm_connector_property_set_value(connector,
|
||||
property,
|
||||
value))
|
||||
return -1;
|
||||
|
||||
if (crtc->saved_mode.hdisplay != 0 &&
|
||||
crtc->saved_mode.vdisplay != 0) {
|
||||
if (!drm_crtc_helper_set_mode(encoder->crtc,
|
||||
&crtc->saved_mode,
|
||||
encoder->crtc->x,
|
||||
encoder->crtc->y,
|
||||
encoder->crtc->fb))
|
||||
return -1;
|
||||
}
|
||||
} else if (!strcmp(property->name, "backlight") && encoder) {
|
||||
if (drm_connector_property_set_value(connector,
|
||||
property,
|
||||
value))
|
||||
return -1;
|
||||
else {
|
||||
#ifdef CONFIG_BACKLIGHT_CLASS_DEVICE
|
||||
struct drm_psb_private *dev_priv =
|
||||
encoder->dev->dev_private;
|
||||
struct backlight_device *bd = dev_priv->backlight_device;
|
||||
bd->props.brightness = value;
|
||||
backlight_update_status(bd);
|
||||
#endif
|
||||
}
|
||||
} else if (!strcmp(property->name, "DPMS") && encoder) {
|
||||
struct drm_encoder_helper_funcs *helpers = encoder->helper_private;
|
||||
helpers->dpms(encoder, value);
|
||||
}
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct drm_encoder_helper_funcs cdv_intel_lvds_helper_funcs = {
|
||||
.dpms = cdv_intel_lvds_encoder_dpms,
|
||||
.mode_fixup = cdv_intel_lvds_mode_fixup,
|
||||
.prepare = cdv_intel_lvds_prepare,
|
||||
.mode_set = cdv_intel_lvds_mode_set,
|
||||
.commit = cdv_intel_lvds_commit,
|
||||
};
|
||||
|
||||
static const struct drm_connector_helper_funcs
|
||||
cdv_intel_lvds_connector_helper_funcs = {
|
||||
.get_modes = cdv_intel_lvds_get_modes,
|
||||
.mode_valid = cdv_intel_lvds_mode_valid,
|
||||
.best_encoder = psb_intel_best_encoder,
|
||||
};
|
||||
|
||||
static const struct drm_connector_funcs cdv_intel_lvds_connector_funcs = {
|
||||
.dpms = drm_helper_connector_dpms,
|
||||
.save = cdv_intel_lvds_save,
|
||||
.restore = cdv_intel_lvds_restore,
|
||||
.detect = cdv_intel_lvds_detect,
|
||||
.fill_modes = drm_helper_probe_single_connector_modes,
|
||||
.set_property = cdv_intel_lvds_set_property,
|
||||
.destroy = cdv_intel_lvds_destroy,
|
||||
};
|
||||
|
||||
|
||||
static void cdv_intel_lvds_enc_destroy(struct drm_encoder *encoder)
|
||||
{
|
||||
drm_encoder_cleanup(encoder);
|
||||
}
|
||||
|
||||
const struct drm_encoder_funcs cdv_intel_lvds_enc_funcs = {
|
||||
.destroy = cdv_intel_lvds_enc_destroy,
|
||||
};
|
||||
|
||||
/**
|
||||
* cdv_intel_lvds_init - setup LVDS connectors on this device
|
||||
* @dev: drm device
|
||||
*
|
||||
* Create the connector, register the LVDS DDC bus, and try to figure out what
|
||||
* modes we can display on the LVDS panel (if present).
|
||||
*/
|
||||
void cdv_intel_lvds_init(struct drm_device *dev,
|
||||
struct psb_intel_mode_device *mode_dev)
|
||||
{
|
||||
struct psb_intel_output *psb_intel_output;
|
||||
struct cdv_intel_lvds_priv *lvds_priv;
|
||||
struct drm_connector *connector;
|
||||
struct drm_encoder *encoder;
|
||||
struct drm_display_mode *scan;
|
||||
struct drm_crtc *crtc;
|
||||
struct drm_psb_private *dev_priv = dev->dev_private;
|
||||
u32 lvds;
|
||||
int pipe;
|
||||
|
||||
psb_intel_output = kzalloc(sizeof(struct psb_intel_output) +
|
||||
sizeof(struct cdv_intel_lvds_priv), GFP_KERNEL);
|
||||
if (!psb_intel_output)
|
||||
return;
|
||||
|
||||
lvds_priv = (struct cdv_intel_lvds_priv *)(psb_intel_output + 1);
|
||||
|
||||
psb_intel_output->dev_priv = lvds_priv;
|
||||
|
||||
psb_intel_output->mode_dev = mode_dev;
|
||||
connector = &psb_intel_output->base;
|
||||
encoder = &psb_intel_output->enc;
|
||||
|
||||
|
||||
drm_connector_init(dev, &psb_intel_output->base,
|
||||
&cdv_intel_lvds_connector_funcs,
|
||||
DRM_MODE_CONNECTOR_LVDS);
|
||||
|
||||
drm_encoder_init(dev, &psb_intel_output->enc,
|
||||
&cdv_intel_lvds_enc_funcs,
|
||||
DRM_MODE_ENCODER_LVDS);
|
||||
|
||||
|
||||
drm_mode_connector_attach_encoder(&psb_intel_output->base,
|
||||
&psb_intel_output->enc);
|
||||
psb_intel_output->type = INTEL_OUTPUT_LVDS;
|
||||
|
||||
drm_encoder_helper_add(encoder, &cdv_intel_lvds_helper_funcs);
|
||||
drm_connector_helper_add(connector,
|
||||
&cdv_intel_lvds_connector_helper_funcs);
|
||||
connector->display_info.subpixel_order = SubPixelHorizontalRGB;
|
||||
connector->interlace_allowed = false;
|
||||
connector->doublescan_allowed = false;
|
||||
|
||||
/*Attach connector properties*/
|
||||
drm_connector_attach_property(connector,
|
||||
dev->mode_config.scaling_mode_property,
|
||||
DRM_MODE_SCALE_FULLSCREEN);
|
||||
drm_connector_attach_property(connector,
|
||||
dev_priv->backlight_property,
|
||||
BRIGHTNESS_MAX_LEVEL);
|
||||
|
||||
/**
|
||||
* Set up I2C bus
|
||||
* FIXME: distroy i2c_bus when exit
|
||||
*/
|
||||
psb_intel_output->i2c_bus = psb_intel_i2c_create(dev,
|
||||
GPIOB,
|
||||
"LVDSBLC_B");
|
||||
if (!psb_intel_output->i2c_bus) {
|
||||
dev_printk(KERN_ERR,
|
||||
&dev->pdev->dev, "I2C bus registration failed.\n");
|
||||
goto failed_blc_i2c;
|
||||
}
|
||||
psb_intel_output->i2c_bus->slave_addr = 0x2C;
|
||||
dev_priv->lvds_i2c_bus = psb_intel_output->i2c_bus;
|
||||
|
||||
/*
|
||||
* LVDS discovery:
|
||||
* 1) check for EDID on DDC
|
||||
* 2) check for VBT data
|
||||
* 3) check to see if LVDS is already on
|
||||
* if none of the above, no panel
|
||||
* 4) make sure lid is open
|
||||
* if closed, act like it's not there for now
|
||||
*/
|
||||
|
||||
/* Set up the DDC bus. */
|
||||
psb_intel_output->ddc_bus = psb_intel_i2c_create(dev,
|
||||
GPIOC,
|
||||
"LVDSDDC_C");
|
||||
if (!psb_intel_output->ddc_bus) {
|
||||
dev_printk(KERN_ERR, &dev->pdev->dev,
|
||||
"DDC bus registration " "failed.\n");
|
||||
goto failed_ddc;
|
||||
}
|
||||
|
||||
/*
|
||||
* Attempt to get the fixed panel mode from DDC. Assume that the
|
||||
* preferred mode is the right one.
|
||||
*/
|
||||
psb_intel_ddc_get_modes(psb_intel_output);
|
||||
list_for_each_entry(scan, &connector->probed_modes, head) {
|
||||
if (scan->type & DRM_MODE_TYPE_PREFERRED) {
|
||||
mode_dev->panel_fixed_mode =
|
||||
drm_mode_duplicate(dev, scan);
|
||||
goto out; /* FIXME: check for quirks */
|
||||
}
|
||||
}
|
||||
|
||||
/* Failed to get EDID, what about VBT? do we need this?*/
|
||||
if (dev_priv->lfp_lvds_vbt_mode) {
|
||||
mode_dev->panel_fixed_mode =
|
||||
drm_mode_duplicate(dev, dev_priv->lfp_lvds_vbt_mode);
|
||||
if (mode_dev->panel_fixed_mode) {
|
||||
mode_dev->panel_fixed_mode->type |=
|
||||
DRM_MODE_TYPE_PREFERRED;
|
||||
goto out; /* FIXME: check for quirks */
|
||||
}
|
||||
}
|
||||
/*
|
||||
* If we didn't get EDID, try checking if the panel is already turned
|
||||
* on. If so, assume that whatever is currently programmed is the
|
||||
* correct mode.
|
||||
*/
|
||||
lvds = REG_READ(LVDS);
|
||||
pipe = (lvds & LVDS_PIPEB_SELECT) ? 1 : 0;
|
||||
crtc = psb_intel_get_crtc_from_pipe(dev, pipe);
|
||||
|
||||
if (crtc && (lvds & LVDS_PORT_EN)) {
|
||||
mode_dev->panel_fixed_mode =
|
||||
cdv_intel_crtc_mode_get(dev, crtc);
|
||||
if (mode_dev->panel_fixed_mode) {
|
||||
mode_dev->panel_fixed_mode->type |=
|
||||
DRM_MODE_TYPE_PREFERRED;
|
||||
goto out; /* FIXME: check for quirks */
|
||||
}
|
||||
}
|
||||
|
||||
/* If we still don't have a mode after all that, give up. */
|
||||
if (!mode_dev->panel_fixed_mode) {
|
||||
DRM_DEBUG
|
||||
("Found no modes on the lvds, ignoring the LVDS\n");
|
||||
goto failed_find;
|
||||
}
|
||||
|
||||
out:
|
||||
drm_sysfs_connector_add(connector);
|
||||
return;
|
||||
|
||||
failed_find:
|
||||
printk(KERN_ERR "Failed find\n");
|
||||
if (psb_intel_output->ddc_bus)
|
||||
psb_intel_i2c_destroy(psb_intel_output->ddc_bus);
|
||||
failed_ddc:
|
||||
printk(KERN_ERR "Failed DDC\n");
|
||||
if (psb_intel_output->i2c_bus)
|
||||
psb_intel_i2c_destroy(psb_intel_output->i2c_bus);
|
||||
failed_blc_i2c:
|
||||
printk(KERN_ERR "Failed BLC\n");
|
||||
drm_encoder_cleanup(encoder);
|
||||
drm_connector_cleanup(connector);
|
||||
kfree(connector);
|
||||
}
|
|
@ -732,6 +732,10 @@ static void psb_setup_outputs(struct drm_device *dev)
|
|||
|
||||
/* valid crtcs */
|
||||
switch (psb_intel_output->type) {
|
||||
case INTEL_OUTPUT_ANALOG:
|
||||
crtc_mask = (1 << 0);
|
||||
clone_mask = (1 << INTEL_OUTPUT_ANALOG);
|
||||
break;
|
||||
case INTEL_OUTPUT_SDVO:
|
||||
crtc_mask = ((1 << 0) | (1 << 1));
|
||||
clone_mask = (1 << INTEL_OUTPUT_SDVO);
|
||||
|
@ -752,7 +756,10 @@ static void psb_setup_outputs(struct drm_device *dev)
|
|||
clone_mask = (1 << INTEL_OUTPUT_MIPI2);
|
||||
break;
|
||||
case INTEL_OUTPUT_HDMI:
|
||||
crtc_mask = (1 << 1);
|
||||
if (IS_MFLD(dev))
|
||||
crtc_mask = (1 << 1);
|
||||
else /* FIXME: review Oaktrail */
|
||||
crtc_mask = (1 << 0); /* Cedarview */
|
||||
clone_mask = (1 << INTEL_OUTPUT_HDMI);
|
||||
break;
|
||||
}
|
||||
|
|
|
@ -395,12 +395,10 @@ int psb_gtt_init(struct drm_device *dev, int resume)
|
|||
(void) PSB_RVDC32(PSB_PGETBL_CTL);
|
||||
|
||||
/* The root resource we allocate address space from */
|
||||
dev_priv->gtt_mem = &dev->pdev->resource[PSB_GATT_RESOURCE];
|
||||
dev_priv->gtt_initialized = 1;
|
||||
|
||||
pg->gtt_phys_start = dev_priv->pge_ctl & PAGE_MASK;
|
||||
|
||||
pg->gatt_start = pci_resource_start(dev->pdev, PSB_GATT_RESOURCE);
|
||||
pg->gtt_phys_start = dev_priv->pge_ctl;
|
||||
|
||||
/*
|
||||
* FIXME: video mmu has hw bug to access 0x0D0000000,
|
||||
* then make gatt start at 0x0e000,0000
|
||||
|
@ -410,8 +408,33 @@ int psb_gtt_init(struct drm_device *dev, int resume)
|
|||
pg->gtt_start = pci_resource_start(dev->pdev, PSB_GTT_RESOURCE);
|
||||
gtt_pages = pci_resource_len(dev->pdev, PSB_GTT_RESOURCE)
|
||||
>> PAGE_SHIFT;
|
||||
/* CDV workaround */
|
||||
if (pg->gtt_start == 0 || gtt_pages == 0) {
|
||||
dev_err(dev->dev, "GTT PCI BAR not initialized.\n");
|
||||
gtt_pages = 64;
|
||||
pg->gtt_start = dev_priv->pge_ctl;
|
||||
}
|
||||
|
||||
pg->gatt_start = pci_resource_start(dev->pdev, PSB_GATT_RESOURCE);
|
||||
pg->gatt_pages = pci_resource_len(dev->pdev, PSB_GATT_RESOURCE)
|
||||
>> PAGE_SHIFT;
|
||||
dev_priv->gtt_mem = &dev->pdev->resource[PSB_GATT_RESOURCE];
|
||||
|
||||
if (pg->gatt_pages == 0 || pg->gatt_start == 0) {
|
||||
static struct resource fudge; /* Preferably peppermint */
|
||||
|
||||
/* This can occur on CDV SDV systems. Fudge it in this case.
|
||||
We really don't care what imaginary space is being allocated
|
||||
at this point */
|
||||
dev_err(dev->dev, "GATT PCI BAR not initialized.\n");
|
||||
pg->gatt_start = 0x40000000;
|
||||
pg->gatt_pages = (128 * 1024 * 1024) >> PAGE_SHIFT;
|
||||
fudge.start = 0x40000000;
|
||||
fudge.end = 0x40000000 + 128 * 1024 * 1024 - 1;
|
||||
fudge.name = "fudge";
|
||||
fudge.flags = IORESOURCE_MEM;
|
||||
dev_priv->gtt_mem = &fudge;
|
||||
}
|
||||
|
||||
pci_read_config_dword(dev->pdev, PSB_BSM, &dev_priv->stolen_base);
|
||||
vram_stolen_size = pg->gtt_phys_start - dev_priv->stolen_base
|
||||
|
@ -463,7 +486,7 @@ int psb_gtt_init(struct drm_device *dev, int resume)
|
|||
pfn_base = dev_priv->stolen_base >> PAGE_SHIFT;
|
||||
vram_pages = num_pages = vram_stolen_size >> PAGE_SHIFT;
|
||||
printk(KERN_INFO"Set up %d stolen pages starting at 0x%08x, GTT offset %dK\n",
|
||||
num_pages, pfn_base, 0);
|
||||
num_pages, pfn_base << PAGE_SHIFT, 0);
|
||||
for (i = 0; i < num_pages; ++i) {
|
||||
pte = psb_gtt_mask_pte(pfn_base + i, 0);
|
||||
iowrite32(pte, dev_priv->gtt_map + i);
|
||||
|
|
|
@ -1039,14 +1039,13 @@ static int psb_intel_crtc_cursor_set(struct drm_crtc *crtc,
|
|||
}
|
||||
|
||||
/* unpin the old bo */
|
||||
if (psb_intel_crtc->cursor_obj && psb_intel_crtc->cursor_obj != obj) {
|
||||
if (psb_intel_crtc->cursor_obj) {
|
||||
gt = container_of(psb_intel_crtc->cursor_obj,
|
||||
struct gtt_range, gem);
|
||||
psb_gtt_unpin(gt);
|
||||
drm_gem_object_unreference(psb_intel_crtc->cursor_obj);
|
||||
psb_intel_crtc->cursor_obj = obj;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
|
|
|
@ -142,6 +142,8 @@
|
|||
#define DPLLB_LVDS_P2_CLOCK_DIV_7 (1 << 24) /* i915 */
|
||||
#define DPLL_P2_CLOCK_DIV_MASK 0x03000000 /* i915 */
|
||||
#define DPLL_FPA01_P1_POST_DIV_MASK 0x00ff0000 /* i915 */
|
||||
#define DPLL_LOCK (1 << 15) /* CDV */
|
||||
|
||||
/*
|
||||
* The i830 generation, in DAC/serial mode, defines p1 as two plus this
|
||||
* bitfield, or just 2 if PLL_P1_DIVIDE_BY_TWO is set.
|
||||
|
@ -271,6 +273,20 @@
|
|||
#define TV_HOTPLUG_INT_EN (1 << 18)
|
||||
#define CRT_HOTPLUG_INT_EN (1 << 9)
|
||||
#define CRT_HOTPLUG_FORCE_DETECT (1 << 3)
|
||||
/* CDV.. */
|
||||
#define CRT_HOTPLUG_ACTIVATION_PERIOD_64 (1 << 8)
|
||||
#define CRT_HOTPLUG_DAC_ON_TIME_2M (0 << 7)
|
||||
#define CRT_HOTPLUG_DAC_ON_TIME_4M (1 << 7)
|
||||
#define CRT_HOTPLUG_VOLTAGE_COMPARE_40 (0 << 5)
|
||||
#define CRT_HOTPLUG_VOLTAGE_COMPARE_50 (1 << 5)
|
||||
#define CRT_HOTPLUG_VOLTAGE_COMPARE_60 (2 << 5)
|
||||
#define CRT_HOTPLUG_VOLTAGE_COMPARE_70 (3 << 5)
|
||||
#define CRT_HOTPLUG_VOLTAGE_COMPARE_MASK (3 << 5)
|
||||
#define CRT_HOTPLUG_DETECT_DELAY_1G (0 << 4)
|
||||
#define CRT_HOTPLUG_DETECT_DELAY_2G (1 << 4)
|
||||
#define CRT_HOTPLUG_DETECT_VOLTAGE_325MV (0 << 2)
|
||||
#define CRT_HOTPLUG_DETECT_VOLTAGE_475MV (1 << 2)
|
||||
#define CRT_HOTPLUG_DETECT_MASK 0x000000F8
|
||||
|
||||
#define PORT_HOTPLUG_STAT 0x61114
|
||||
#define CRT_HOTPLUG_INT_STATUS (1 << 11)
|
||||
|
@ -1141,4 +1157,79 @@ No status bits are changed.
|
|||
#define SKU_100L 0x04
|
||||
#define SKU_BYPASS 0x08
|
||||
|
||||
/* Some handy macros for playing with bitfields. */
|
||||
#define PSB_MASK(high, low) (((1<<((high)-(low)+1))-1)<<(low))
|
||||
#define SET_FIELD(value, field) (((value) << field ## _SHIFT) & field ## _MASK)
|
||||
#define GET_FIELD(word, field) (((word) & field ## _MASK) >> field ## _SHIFT)
|
||||
|
||||
#define _PIPE(pipe, a, b) ((a) + (pipe)*((b)-(a)))
|
||||
|
||||
/* PCI config space */
|
||||
|
||||
#define SB_PCKT 0x02100 /* cedarview */
|
||||
# define SB_OPCODE_MASK PSB_MASK(31, 16)
|
||||
# define SB_OPCODE_SHIFT 16
|
||||
# define SB_OPCODE_READ 0
|
||||
# define SB_OPCODE_WRITE 1
|
||||
# define SB_DEST_MASK PSB_MASK(15, 8)
|
||||
# define SB_DEST_SHIFT 8
|
||||
# define SB_DEST_DPLL 0x88
|
||||
# define SB_BYTE_ENABLE_MASK PSB_MASK(7, 4)
|
||||
# define SB_BYTE_ENABLE_SHIFT 4
|
||||
# define SB_BUSY (1 << 0)
|
||||
|
||||
|
||||
/* 32-bit value read/written from the DPIO reg. */
|
||||
#define SB_DATA 0x02104 /* cedarview */
|
||||
/* 32-bit address of the DPIO reg to be read/written. */
|
||||
#define SB_ADDR 0x02108 /* cedarview */
|
||||
#define DPIO_CFG 0x02110 /* cedarview */
|
||||
# define DPIO_MODE_SELECT_1 (1 << 3)
|
||||
# define DPIO_MODE_SELECT_0 (1 << 2)
|
||||
# define DPIO_SFR_BYPASS (1 << 1)
|
||||
/* reset is active low */
|
||||
# define DPIO_CMN_RESET_N (1 << 0)
|
||||
|
||||
/* Cedarview sideband registers */
|
||||
#define _SB_M_A 0x8008
|
||||
#define _SB_M_B 0x8028
|
||||
#define SB_M(pipe) _PIPE(pipe, _SB_M_A, _SB_M_B)
|
||||
# define SB_M_DIVIDER_MASK (0xFF << 24)
|
||||
# define SB_M_DIVIDER_SHIFT 24
|
||||
|
||||
#define _SB_N_VCO_A 0x8014
|
||||
#define _SB_N_VCO_B 0x8034
|
||||
#define SB_N_VCO(pipe) _PIPE(pipe, _SB_N_VCO_A, _SB_N_VCO_B)
|
||||
#define SB_N_VCO_SEL_MASK PSB_MASK(31, 30)
|
||||
#define SB_N_VCO_SEL_SHIFT 30
|
||||
#define SB_N_DIVIDER_MASK PSB_MASK(29, 26)
|
||||
#define SB_N_DIVIDER_SHIFT 26
|
||||
#define SB_N_CB_TUNE_MASK PSB_MASK(25, 24)
|
||||
#define SB_N_CB_TUNE_SHIFT 24
|
||||
|
||||
#define _SB_REF_A 0x8018
|
||||
#define _SB_REF_B 0x8038
|
||||
#define SB_REF_SFR(pipe) _PIPE(pipe, _SB_REF_A, _SB_REF_B)
|
||||
|
||||
#define _SB_P_A 0x801c
|
||||
#define _SB_P_B 0x803c
|
||||
#define SB_P(pipe) _PIPE(pipe, _SB_P_A, _SB_P_B)
|
||||
#define SB_P2_DIVIDER_MASK PSB_MASK(31, 30)
|
||||
#define SB_P2_DIVIDER_SHIFT 30
|
||||
#define SB_P2_10 0 /* HDMI, DP, DAC */
|
||||
#define SB_P2_5 1 /* DAC */
|
||||
#define SB_P2_14 2 /* LVDS single */
|
||||
#define SB_P2_7 3 /* LVDS double */
|
||||
#define SB_P1_DIVIDER_MASK PSB_MASK(15, 12)
|
||||
#define SB_P1_DIVIDER_SHIFT 12
|
||||
|
||||
#define PSB_LANE0 0x120
|
||||
#define PSB_LANE1 0x220
|
||||
#define PSB_LANE2 0x2320
|
||||
#define PSB_LANE3 0x2420
|
||||
|
||||
#define LANE_PLL_MASK (0x7 << 20)
|
||||
#define LANE_PLL_ENABLE (0x3 << 20)
|
||||
|
||||
|
||||
#endif
|
||||
|
|
Loading…
Reference in a new issue