diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
index 2ddd86ddf649..383f057b8fc3 100644
--- a/drivers/media/i2c/ov5640.c
+++ b/drivers/media/i2c/ov5640.c
@@ -287,10 +287,10 @@ static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
 	{0x3a0d, 0x04, 0, 0}, {0x3a14, 0x03, 0, 0}, {0x3a15, 0xd8, 0, 0},
 	{0x4001, 0x02, 0, 0}, {0x4004, 0x02, 0, 0}, {0x3000, 0x00, 0, 0},
 	{0x3002, 0x1c, 0, 0}, {0x3004, 0xff, 0, 0}, {0x3006, 0xc3, 0, 0},
-	{0x300e, 0x45, 0, 0}, {0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
+	{0x302e, 0x08, 0, 0}, {0x4300, 0x3f, 0, 0},
 	{0x501f, 0x00, 0, 0}, {0x4713, 0x03, 0, 0}, {0x4407, 0x04, 0, 0},
 	{0x440e, 0x00, 0, 0}, {0x460b, 0x35, 0, 0}, {0x460c, 0x22, 0, 0},
-	{0x4837, 0x0a, 0, 0}, {0x4800, 0x04, 0, 0}, {0x3824, 0x02, 0, 0},
+	{0x4837, 0x0a, 0, 0}, {0x3824, 0x02, 0, 0},
 	{0x5000, 0xa7, 0, 0}, {0x5001, 0xa3, 0, 0}, {0x5180, 0xff, 0, 0},
 	{0x5181, 0xf2, 0, 0}, {0x5182, 0x00, 0, 0}, {0x5183, 0x14, 0, 0},
 	{0x5184, 0x25, 0, 0}, {0x5185, 0x24, 0, 0}, {0x5186, 0x09, 0, 0},
@@ -1103,12 +1103,25 @@ static int ov5640_set_stream_mipi(struct ov5640_dev *sensor, bool on)
 {
 	int ret;
 
-	ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
-			     on ? 0 : BIT(5));
-	if (ret)
-		return ret;
-	ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
-			       on ? 0x00 : 0x70);
+	/*
+	 * Enable/disable the MIPI interface
+	 *
+	 * 0x300e = on ? 0x45 : 0x40
+	 *
+	 * FIXME: the sensor manual (version 2.03) reports
+	 * [7:5] = 000  : 1 data lane mode
+	 * [7:5] = 001  : 2 data lanes mode
+	 * But this settings do not work, while the following ones
+	 * have been validated for 2 data lanes mode.
+	 *
+	 * [7:5] = 010	: 2 data lanes mode
+	 * [4] = 0	: Power up MIPI HS Tx
+	 * [3] = 0	: Power up MIPI LS Rx
+	 * [2] = 1/0	: MIPI interface enable/disable
+	 * [1:0] = 01/00: FIXME: 'debug'
+	 */
+	ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00,
+			       on ? 0x45 : 0x40);
 	if (ret)
 		return ret;
 
@@ -1787,23 +1800,69 @@ static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
 		if (ret)
 			goto power_off;
 
+		/* We're done here for DVP bus, while CSI-2 needs setup. */
+		if (sensor->ep.bus_type != V4L2_MBUS_CSI2)
+			return 0;
+
+		/*
+		 * Power up MIPI HS Tx and LS Rx; 2 data lanes mode
+		 *
+		 * 0x300e = 0x40
+		 * [7:5] = 010	: 2 data lanes mode (see FIXME note in
+		 *		  "ov5640_set_stream_mipi()")
+		 * [4] = 0	: Power up MIPI HS Tx
+		 * [3] = 0	: Power up MIPI LS Rx
+		 * [2] = 0	: MIPI interface disabled
+		 */
+		ret = ov5640_write_reg(sensor,
+				       OV5640_REG_IO_MIPI_CTRL00, 0x40);
+		if (ret)
+			goto power_off;
+
+		/*
+		 * Gate clock and set LP11 in 'no packets mode' (idle)
+		 *
+		 * 0x4800 = 0x24
+		 * [5] = 1	: Gate clock when 'no packets'
+		 * [2] = 1	: MIPI bus in LP11 when 'no packets'
+		 */
+		ret = ov5640_write_reg(sensor,
+				       OV5640_REG_MIPI_CTRL00, 0x24);
+		if (ret)
+			goto power_off;
+
+		/*
+		 * Set data lanes and clock in LP11 when 'sleeping'
+		 *
+		 * 0x3019 = 0x70
+		 * [6] = 1	: MIPI data lane 2 in LP11 when 'sleeping'
+		 * [5] = 1	: MIPI data lane 1 in LP11 when 'sleeping'
+		 * [4] = 1	: MIPI clock lane in LP11 when 'sleeping'
+		 */
+		ret = ov5640_write_reg(sensor,
+				       OV5640_REG_PAD_OUTPUT00, 0x70);
+		if (ret)
+			goto power_off;
+
+		/* Give lanes some time to coax into LP11 state. */
+		usleep_range(500, 1000);
+
+	} else {
 		if (sensor->ep.bus_type == V4L2_MBUS_CSI2) {
-			/*
-			 * start streaming briefly followed by stream off in
-			 * order to coax the clock lane into LP-11 state.
-			 */
-			ret = ov5640_set_stream_mipi(sensor, true);
-			if (ret)
-				goto power_off;
-			usleep_range(1000, 2000);
-			ret = ov5640_set_stream_mipi(sensor, false);
-			if (ret)
-				goto power_off;
+			/* Reset MIPI bus settings to their default values. */
+			ov5640_write_reg(sensor,
+					 OV5640_REG_IO_MIPI_CTRL00, 0x58);
+			ov5640_write_reg(sensor,
+					 OV5640_REG_MIPI_CTRL00, 0x04);
+			ov5640_write_reg(sensor,
+					 OV5640_REG_PAD_OUTPUT00, 0x00);
 		}
 
-		return 0;
+		ov5640_set_power_off(sensor);
 	}
 
+	return 0;
+
 power_off:
 	ov5640_set_power_off(sensor);
 	return ret;