From ab60075f2a4eebca1abb04f712569963fb4d9d6c Mon Sep 17 00:00:00 2001 From: "Ji-Ze Hong (Peter Hong)" Date: Thu, 15 Nov 2018 10:58:44 +0800 Subject: [PATCH] USB: serial: f81534: fix reading old/new IC config The F81532/534 had a internal configuration space to save & control IC state with address F81534_CUSTOM_ADDRESS_START (0x2f00). Layout as following: +00h: to indicate the section is valid +01h~04h: UART Mode & port availability +05h~08h: Output pin control on IC power on +09h~12h: Output pin control on working <-- New added Old driver will use +05~08h as default on working, but newer IC will configed with shutdown mode(7) in 05h~08h and working mode with RS232(1) in 09h~12h. It'll make mainstream driver not working. This patch will make mainstream driver compatible older and newer IC. If using a old IC, the +05h~08h will be 00h~06h, we'll direct apply it. If using a new IC, the +05h~08h will be 07h or larger, we'll read +09h~12h to apply newer configuration. Signed-off-by: Ji-Ze Hong (Peter Hong) Signed-off-by: Johan Hovold --- drivers/usb/serial/f81534.c | 20 +++++++++++++++++--- 1 file changed, 17 insertions(+), 3 deletions(-) diff --git a/drivers/usb/serial/f81534.c b/drivers/usb/serial/f81534.c index 380933db34dd..2b39bda035c7 100644 --- a/drivers/usb/serial/f81534.c +++ b/drivers/usb/serial/f81534.c @@ -45,14 +45,17 @@ #define F81534_CONFIG1_REG (0x09 + F81534_UART_BASE_ADDRESS) #define F81534_DEF_CONF_ADDRESS_START 0x3000 -#define F81534_DEF_CONF_SIZE 8 +#define F81534_DEF_CONF_SIZE 12 #define F81534_CUSTOM_ADDRESS_START 0x2f00 #define F81534_CUSTOM_DATA_SIZE 0x10 #define F81534_CUSTOM_NO_CUSTOM_DATA 0xff #define F81534_CUSTOM_VALID_TOKEN 0xf0 #define F81534_CONF_OFFSET 1 -#define F81534_CONF_GPIO_OFFSET 4 +#define F81534_CONF_INIT_GPIO_OFFSET 4 +#define F81534_CONF_WORK_GPIO_OFFSET 8 +#define F81534_CONF_GPIO_SHUTDOWN 7 +#define F81534_CONF_GPIO_RS232 1 #define F81534_MAX_DATA_BLOCK 64 #define F81534_MAX_BUS_RETRY 20 @@ -1337,8 +1340,19 @@ static int f81534_set_port_output_pin(struct usb_serial_port *port) serial_priv = usb_get_serial_data(serial); port_priv = usb_get_serial_port_data(port); - idx = F81534_CONF_GPIO_OFFSET + port_priv->phy_num; + idx = F81534_CONF_INIT_GPIO_OFFSET + port_priv->phy_num; value = serial_priv->conf_data[idx]; + if (value >= F81534_CONF_GPIO_SHUTDOWN) { + /* + * Newer IC configure will make transceiver in shutdown mode on + * initial power on. We need enable it before using UARTs. + */ + idx = F81534_CONF_WORK_GPIO_OFFSET + port_priv->phy_num; + value = serial_priv->conf_data[idx]; + if (value >= F81534_CONF_GPIO_SHUTDOWN) + value = F81534_CONF_GPIO_RS232; + } + pins = &f81534_port_out_pins[port_priv->phy_num]; for (i = 0; i < ARRAY_SIZE(pins->pin); ++i) {