net: phy: realtek: fix rtl8211e rx/tx delay config
There are two chip pins named TXDLY and RXDLY which actually adds the 2ns
delays to TXC and RXC for TXD/RXD latching. These two pins can config via
4.7k-ohm resistor to 3.3V hw setting, but also config via software setting
(extension page 0xa4 register 0x1c bit13 12 and 11).
The configuration register definitions from table 13 official PHY datasheet:
PHYAD[2:0] = PHY Address
AN[1:0] = Auto-Negotiation
Mode = Interface Mode Select
RX Delay = RX Delay
TX Delay = TX Delay
SELRGV = RGMII/GMII Selection
This table describes how to config these hw pins via external pull-high or pull-
low resistor.
It is a misunderstanding that mapping it as register bits below:
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
So I removed these descriptions above and add related settings as below:
14 = reserved
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay
10:0 = Test && debug settings reserved by realtek
Test && debug settings are not recommend to modify by default.
Fixes: f81dadbcf7
("net: phy: realtek: Add rtl8211e rx/tx delays config")
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is contained in:
parent
1a03b8a35a
commit
bbc4d71d63
|
@ -1,6 +1,5 @@
|
||||||
// SPDX-License-Identifier: GPL-2.0+
|
// SPDX-License-Identifier: GPL-2.0+
|
||||||
/*
|
/* drivers/net/phy/realtek.c
|
||||||
* drivers/net/phy/realtek.c
|
|
||||||
*
|
*
|
||||||
* Driver for Realtek PHYs
|
* Driver for Realtek PHYs
|
||||||
*
|
*
|
||||||
|
@ -32,9 +31,9 @@
|
||||||
#define RTL8211F_TX_DELAY BIT(8)
|
#define RTL8211F_TX_DELAY BIT(8)
|
||||||
#define RTL8211F_RX_DELAY BIT(3)
|
#define RTL8211F_RX_DELAY BIT(3)
|
||||||
|
|
||||||
#define RTL8211E_TX_DELAY BIT(1)
|
#define RTL8211E_CTRL_DELAY BIT(13)
|
||||||
#define RTL8211E_RX_DELAY BIT(2)
|
#define RTL8211E_TX_DELAY BIT(12)
|
||||||
#define RTL8211E_MODE_MII_GMII BIT(3)
|
#define RTL8211E_RX_DELAY BIT(11)
|
||||||
|
|
||||||
#define RTL8201F_ISR 0x1e
|
#define RTL8201F_ISR 0x1e
|
||||||
#define RTL8201F_IER 0x13
|
#define RTL8201F_IER 0x13
|
||||||
|
@ -246,16 +245,16 @@ static int rtl8211e_config_init(struct phy_device *phydev)
|
||||||
/* enable TX/RX delay for rgmii-* modes, and disable them for rgmii. */
|
/* enable TX/RX delay for rgmii-* modes, and disable them for rgmii. */
|
||||||
switch (phydev->interface) {
|
switch (phydev->interface) {
|
||||||
case PHY_INTERFACE_MODE_RGMII:
|
case PHY_INTERFACE_MODE_RGMII:
|
||||||
val = 0;
|
val = RTL8211E_CTRL_DELAY | 0;
|
||||||
break;
|
break;
|
||||||
case PHY_INTERFACE_MODE_RGMII_ID:
|
case PHY_INTERFACE_MODE_RGMII_ID:
|
||||||
val = RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
|
val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
|
||||||
break;
|
break;
|
||||||
case PHY_INTERFACE_MODE_RGMII_RXID:
|
case PHY_INTERFACE_MODE_RGMII_RXID:
|
||||||
val = RTL8211E_RX_DELAY;
|
val = RTL8211E_CTRL_DELAY | RTL8211E_RX_DELAY;
|
||||||
break;
|
break;
|
||||||
case PHY_INTERFACE_MODE_RGMII_TXID:
|
case PHY_INTERFACE_MODE_RGMII_TXID:
|
||||||
val = RTL8211E_TX_DELAY;
|
val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY;
|
||||||
break;
|
break;
|
||||||
default: /* the rest of the modes imply leaving delays as is. */
|
default: /* the rest of the modes imply leaving delays as is. */
|
||||||
return 0;
|
return 0;
|
||||||
|
@ -263,11 +262,12 @@ static int rtl8211e_config_init(struct phy_device *phydev)
|
||||||
|
|
||||||
/* According to a sample driver there is a 0x1c config register on the
|
/* According to a sample driver there is a 0x1c config register on the
|
||||||
* 0xa4 extension page (0x7) layout. It can be used to disable/enable
|
* 0xa4 extension page (0x7) layout. It can be used to disable/enable
|
||||||
* the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
|
* the RX/TX delays otherwise controlled by RXDLY/TXDLY pins.
|
||||||
* also be used to customize the whole configuration register:
|
* The configuration register definition:
|
||||||
* 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
|
* 14 = reserved
|
||||||
* 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
|
* 13 = Force Tx RX Delay controlled by bit12 bit11,
|
||||||
* for details).
|
* 12 = RX Delay, 11 = TX Delay
|
||||||
|
* 10:0 = Test && debug settings reserved by realtek
|
||||||
*/
|
*/
|
||||||
oldpage = phy_select_page(phydev, 0x7);
|
oldpage = phy_select_page(phydev, 0x7);
|
||||||
if (oldpage < 0)
|
if (oldpage < 0)
|
||||||
|
@ -277,7 +277,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
|
||||||
if (ret)
|
if (ret)
|
||||||
goto err_restore_page;
|
goto err_restore_page;
|
||||||
|
|
||||||
ret = __phy_modify(phydev, 0x1c, RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
|
ret = __phy_modify(phydev, 0x1c, RTL8211E_CTRL_DELAY
|
||||||
|
| RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
|
||||||
val);
|
val);
|
||||||
|
|
||||||
err_restore_page:
|
err_restore_page:
|
||||||
|
|
Loading…
Reference in a new issue