+
+
+ Here as a first value the channel-index is taken to get/set the
+ corresponding mixer channel, where 0-63 are the input to output
+ fader and 64-127 the playback to outputs fader. Value 0
+ is channel muted 0 and 32768 an amplification of 1.
+
+ Chn 1-64
+
+ fast mixer for the ALSA-mixer utils. The diagonal of the
+ mixer-matrix is implemented from playback to output.
+
+
+ Line Out
+
+ Name -- "Line Out"
+
+ Access -- Read Write
+
+ Values -- 0 1
+
+ Switching on and off the analog out, which has nothing to do
+ with mixing or routing. the analog outs reflects channel 63,64.
+
+
+--- information (only read access):
+
+ Sample Rate
+
+ Name -- "System Sample Rate"
+
+ Access -- Read-only
+
+ getting the sample rate.
+
+
+ External Rate measured
+
+ Name -- "External Rate"
+
+ Access -- Read only
+
+
+ Should be "Autosync Rate", but Name used is
+ ALSA-Scheme. External Sample frequency liked used on Autosync is
+ reported.
+
+
+ MADI Sync Status
+
+ Name -- "MADI Sync Lock Status"
+
+ Access -- Read
+
+ Values -- 0,1,2
+
+ MADI-Input is 0=Unlocked, 1=Locked, or 2=Synced.
+
+
+ Word Clock Sync Status
+
+ Name -- "Word Clock Lock Status"
+
+ Access -- Read
+
+ Values -- 0,1,2
+
+ Word Clock Input is 0=Unlocked, 1=Locked, or 2=Synced.
+
+ AutoSync
+
+ Name -- "AutoSync Reference"
+
+ Access -- Read
+
+ Values -- "WordClock", "MADI", "None"
+
+ Sync-Reference is either "WordClock", "MADI" or none.
+
+ RX 64ch --- noch nicht implementiert
+
+ MADI-Receiver is in 64 channel mode oder 56 channel mode.
+
+
+ AB_inp --- not tested
+
+ Used input for Auto-Input.
+
+
+ actual Buffer Position --- not implemented
+
+ !!! this is a ALSA internal function, so no control is used !!!
+
+
+
+Calling Parameter:
+
+ index int array (min = 1, max = 8),
+ "Index value for RME HDSPM interface." card-index within ALSA
+
+ note: ALSA-standard
+
+ id string array (min = 1, max = 8),
+ "ID string for RME HDSPM interface."
+
+ note: ALSA-standard
+
+ enable int array (min = 1, max = 8),
+ "Enable/disable specific HDSPM sound-cards."
+
+ note: ALSA-standard
+
+ precise_ptr int array (min = 1, max = 8),
+ "Enable precise pointer, or disable."
+
+ note: Use only when the application supports this (which is a special case).
+
+ line_outs_monitor int array (min = 1, max = 8),
+ "Send playback streams to analog outs by default."
+
+
+ note: each playback channel is mixed to the same numbered output
+ channel (routed). This is against the ALSA-convention, where all
+ channels have to be muted on after loading the driver, but was
+ used before on other cards, so i historically use it again)
+
+
+
+ enable_monitor int array (min = 1, max = 8),
+ "Enable Analog Out on Channel 63/64 by default."
+
+ note: here the analog output is enabled (but not routed).
\ No newline at end of file
diff --git a/Documentation/sysctl/kernel.txt b/Documentation/sysctl/kernel.txt
index 35159176997b..9f11d36a8c10 100644
--- a/Documentation/sysctl/kernel.txt
+++ b/Documentation/sysctl/kernel.txt
@@ -49,6 +49,7 @@ show up in /proc/sys/kernel:
- shmmax [ sysv ipc ]
- shmmni
- stop-a [ SPARC only ]
+- suid_dumpable
- sysrq ==> Documentation/sysrq.txt
- tainted
- threads-max
@@ -300,6 +301,25 @@ kernel. This value defaults to SHMMAX.
==============================================================
+suid_dumpable:
+
+This value can be used to query and set the core dump mode for setuid
+or otherwise protected/tainted binaries. The modes are
+
+0 - (default) - traditional behaviour. Any process which has changed
+ privilege levels or is execute only will not be dumped
+1 - (debug) - all processes dump core when possible. The core dump is
+ owned by the current user and no security is applied. This is
+ intended for system debugging situations only. Ptrace is unchecked.
+2 - (suidsafe) - any binary which normally would not be dumped is dumped
+ readable by root only. This allows the end user to remove
+ such a dump but not access it directly. For security reasons
+ core dumps in this mode will not overwrite one another or
+ other files. This mode is appropriate when adminstrators are
+ attempting to debug problems in a normal environment.
+
+==============================================================
+
tainted:
Non-zero if the kernel has been tainted. Numeric values, which
diff --git a/Documentation/sysrq.txt b/Documentation/sysrq.txt
index f98c2e31c143..136d817c01ba 100644
--- a/Documentation/sysrq.txt
+++ b/Documentation/sysrq.txt
@@ -72,6 +72,8 @@ On all - write a character to /proc/sysrq-trigger. eg:
'b' - Will immediately reboot the system without syncing or unmounting
your disks.
+'c' - Will perform a kexec reboot in order to take a crashdump.
+
'o' - Will shut your system off (if configured and supported).
's' - Will attempt to sync all mounted filesystems.
@@ -122,6 +124,9 @@ useful when you want to exit a program that will not let you switch consoles.
re'B'oot is good when you're unable to shut down. But you should also 'S'ync
and 'U'mount first.
+'C'rashdump can be used to manually trigger a crashdump when the system is hung.
+The kernel needs to have been built with CONFIG_KEXEC enabled.
+
'S'ync is great when your system is locked up, it allows you to sync your
disks and will certainly lessen the chance of data loss and fscking. Note
that the sync hasn't taken place until you see the "OK" and "Done" appear
diff --git a/Documentation/tty.txt b/Documentation/tty.txt
index 3958cf746dde..8ff7bc2a0811 100644
--- a/Documentation/tty.txt
+++ b/Documentation/tty.txt
@@ -22,7 +22,7 @@ copy of the structure. You must not re-register over the top of the line
discipline even with the same data or your computer again will be eaten by
demons.
-In order to remove a line discipline call tty_register_ldisc passing NULL.
+In order to remove a line discipline call tty_unregister_ldisc().
In ancient times this always worked. In modern times the function will
return -EBUSY if the ldisc is currently in use. Since the ldisc referencing
code manages the module counts this should not usually be a concern.
diff --git a/Documentation/video4linux/API.html b/Documentation/video4linux/API.html
index 4b3d8f640a4a..441407b12a9f 100644
--- a/Documentation/video4linux/API.html
+++ b/Documentation/video4linux/API.html
@@ -1,399 +1,16 @@
-
-Video4Linux Kernel API Reference v0.1:19990430
-
-
-
-
-
-Devices
-Video4Linux provides the following sets of device files. These live on the
-character device formerly known as "/dev/bttv". /dev/bttv should be a
-symlink to /dev/video0 for most people.
-
-
-Device Name | Minor Range | Function |
-
---|
/dev/video | 0-63 | Video Capture Interface |
-
/dev/radio | 64-127 | AM/FM Radio Devices |
-
/dev/vtx | 192-223 | Teletext Interface Chips |
-
/dev/vbi | 224-239 | Raw VBI Data (Intercast/teletext) |
-
-
-Video4Linux programs open and scan the devices to find what they are looking
-for. Capability queries define what each interface supports. The
-described API is only defined for video capture cards. The relevant subset
-applies to radio cards. Teletext interfaces talk the existing VTX API.
-
-
Capability Query Ioctl
-The VIDIOCGCAP ioctl call is used to obtain the capability
-information for a video device. The struct video_capability object
-passed to the ioctl is completed and returned. It contains the following
-information
-
-
-name[32] | Canonical name for this interface |
-
type | Type of interface |
-
channels | Number of radio/tv channels if appropriate |
-
audios | Number of audio devices if appropriate |
-
maxwidth | Maximum capture width in pixels |
-
maxheight | Maximum capture height in pixels |
-
minwidth | Minimum capture width in pixels |
-
minheight | Minimum capture height in pixels |
-
-
-The type field lists the capability flags for the device. These are
-as follows
-
-
-Name | Description |
-
---|
VID_TYPE_CAPTURE | Can capture to memory |
-
VID_TYPE_TUNER | Has a tuner of some form |
-
VID_TYPE_TELETEXT | Has teletext capability |
-
VID_TYPE_OVERLAY | Can overlay its image onto the frame buffer |
-
VID_TYPE_CHROMAKEY | Overlay is Chromakeyed |
-
VID_TYPE_CLIPPING | Overlay clipping is supported |
-
VID_TYPE_FRAMERAM | Overlay overwrites frame buffer memory |
-
VID_TYPE_SCALES | The hardware supports image scaling |
-
VID_TYPE_MONOCHROME | Image capture is grey scale only |
-
VID_TYPE_SUBCAPTURE | Capture can be of only part of the image |
-
-
-The minimum and maximum sizes listed for a capture device do not imply all
-that all height/width ratios or sizes within the range are possible. A
-request to set a size will be honoured by the largest available capture
-size whose capture is no large than the requested rectangle in either
-direction. For example the quickcam has 3 fixed settings.
-
-
Frame Buffer
-Capture cards that drop data directly onto the frame buffer must be told the
-base address of the frame buffer, its size and organisation. This is a
-privileged ioctl and one that eventually X itself should set.
-
-The VIDIOCSFBUF ioctl sets the frame buffer parameters for a capture
-card. If the card does not do direct writes to the frame buffer then this
-ioctl will be unsupported. The VIDIOCGFBUF ioctl returns the
-currently used parameters. The structure used in both cases is a
-struct video_buffer.
-
-
-void *base | Base physical address of the buffer |
-
int height | Height of the frame buffer |
-
int width | Width of the frame buffer |
-
int depth | Depth of the frame buffer |
-
int bytesperline | Number of bytes of memory between the start of two adjacent lines |
-
-
-Note that these values reflect the physical layout of the frame buffer.
-The visible area may be smaller. In fact under XFree86 this is commonly the
-case. XFree86 DGA can provide the parameters required to set up this ioctl.
-Setting the base address to NULL indicates there is no physical frame buffer
-access.
-
-
Capture Windows
-The capture area is described by a struct video_window. This defines
-a capture area and the clipping information if relevant. The
-VIDIOCGWIN ioctl recovers the current settings and the
-VIDIOCSWIN sets new values. A successful call to VIDIOCSWIN
-indicates that a suitable set of parameters have been chosen. They do not
-indicate that exactly what was requested was granted. The program should
-call VIDIOCGWIN to check if the nearest match was suitable. The
-struct video_window contains the following fields.
-
-
-x | The X co-ordinate specified in X windows format. |
-
y | The Y co-ordinate specified in X windows format. |
-
width | The width of the image capture. |
-
height | The height of the image capture. |
-
chromakey | A host order RGB32 value for the chroma key. |
-
flags | Additional capture flags. |
-
clips | A list of clipping rectangles. (Set only) |
-
clipcount | The number of clipping rectangles. (Set only) |
-
-
-Clipping rectangles are passed as an array. Each clip consists of the following
-fields available to the user.
-
-
-x | X co-ordinate of rectangle to skip |
-
y | Y co-ordinate of rectangle to skip |
-
width | Width of rectangle to skip |
-
height | Height of rectangle to skip |
-
-
-Merely setting the window does not enable capturing. Overlay capturing
-(i.e. PCI-PCI transfer to the frame buffer of the video card)
-is activated by passing the VIDIOCCAPTURE ioctl a value of 1, and
-disabled by passing it a value of 0.
-
-Some capture devices can capture a subfield of the image they actually see.
-This is indicated when VIDEO_TYPE_SUBCAPTURE is defined.
-The video_capture describes the time and special subfields to capture.
-The video_capture structure contains the following fields.
-
-
-x | X co-ordinate of source rectangle to grab |
-
y | Y co-ordinate of source rectangle to grab |
-
width | Width of source rectangle to grab |
-
height | Height of source rectangle to grab |
-
decimation | Decimation to apply |
-
flags | Flag settings for grabbing |
-
-The available flags are
-
-
-Name | Description |
-
---|
VIDEO_CAPTURE_ODD | Capture only odd frames |
-
VIDEO_CAPTURE_EVEN | Capture only even frames |
-
-
-
Video Sources
-Each video4linux video or audio device captures from one or more
-source channels. Each channel can be queries with the
-VDIOCGCHAN ioctl call. Before invoking this function the caller
-must set the channel field to the channel that is being queried. On return
-the struct video_channel is filled in with information about the
-nature of the channel itself.
-
-The VIDIOCSCHAN ioctl takes an integer argument and switches the
-capture to this input. It is not defined whether parameters such as colour
-settings or tuning are maintained across a channel switch. The caller should
-maintain settings as desired for each channel. (This is reasonable as
-different video inputs may have different properties).
-
-The struct video_channel consists of the following
-
-
-channel | The channel number |
-
name | The input name - preferably reflecting the label
-on the card input itself |
-
tuners | Number of tuners for this input |
-
flags | Properties the tuner has |
-
type | Input type (if known) |
-
norm | The norm for this channel |
-
-
-The flags defined are
-
-
-VIDEO_VC_TUNER | Channel has tuners. |
-
VIDEO_VC_AUDIO | Channel has audio. |
-
VIDEO_VC_NORM | Channel has norm setting. |
-
-
-The types defined are
-
-
-VIDEO_TYPE_TV | The input is a TV input. |
-
VIDEO_TYPE_CAMERA | The input is a camera. |
-
-
-
Image Properties
-The image properties of the picture can be queried with the VIDIOCGPICT
-ioctl which fills in a struct video_picture. The VIDIOCSPICT
-ioctl allows values to be changed. All values except for the palette type
-are scaled between 0-65535.
-
-The struct video_picture consists of the following fields
-
-
-brightness | Picture brightness |
-
hue | Picture hue (colour only) |
-
colour | Picture colour (colour only) |
-
contrast | Picture contrast |
-
whiteness | The whiteness (greyscale only) |
-
depth | The capture depth (may need to match the frame buffer depth) |
-
palette | Reports the palette that should be used for this image |
-
-
-The following palettes are defined
-
-
-VIDEO_PALETTE_GREY | Linear intensity grey scale (255 is brightest). |
-
VIDEO_PALETTE_HI240 | The BT848 8bit colour cube. |
-
VIDEO_PALETTE_RGB565 | RGB565 packed into 16 bit words. |
-
VIDEO_PALETTE_RGB555 | RGV555 packed into 16 bit words, top bit undefined. |
-
VIDEO_PALETTE_RGB24 | RGB888 packed into 24bit words. |
-
VIDEO_PALETTE_RGB32 | RGB888 packed into the low 3 bytes of 32bit words. The top 8bits are undefined. |
-
VIDEO_PALETTE_YUV422 | Video style YUV422 - 8bits packed 4bits Y 2bits U 2bits V |
-
VIDEO_PALETTE_YUYV | Describe me |
-
VIDEO_PALETTE_UYVY | Describe me |
-
VIDEO_PALETTE_YUV420 | YUV420 capture |
-
VIDEO_PALETTE_YUV411 | YUV411 capture |
-
VIDEO_PALETTE_RAW | RAW capture (BT848) |
-
VIDEO_PALETTE_YUV422P | YUV 4:2:2 Planar |
-
VIDEO_PALETTE_YUV411P | YUV 4:1:1 Planar |
-
-
-
Tuning
-Each video input channel can have one or more tuners associated with it. Many
-devices will not have tuners. TV cards and radio cards will have one or more
-tuners attached.
-
-Tuners are described by a struct video_tuner which can be obtained by
-the VIDIOCGTUNER ioctl. Fill in the tuner number in the structure
-then pass the structure to the ioctl to have the data filled in. The
-tuner can be switched using VIDIOCSTUNER which takes an integer argument
-giving the tuner to use. A struct tuner has the following fields
-
-
-tuner | Number of the tuner |
-
name | Canonical name for this tuner (eg FM/AM/TV) |
-
rangelow | Lowest tunable frequency |
-
rangehigh | Highest tunable frequency |
-
flags | Flags describing the tuner |
-
mode | The video signal mode if relevant |
-
signal | Signal strength if known - between 0-65535 |
-
-
-The following flags exist
-
-
-VIDEO_TUNER_PAL | PAL tuning is supported |
-
VIDEO_TUNER_NTSC | NTSC tuning is supported |
-
VIDEO_TUNER_SECAM | SECAM tuning is supported |
-
VIDEO_TUNER_LOW | Frequency is in a lower range |
-
VIDEO_TUNER_NORM | The norm for this tuner is settable |
-
VIDEO_TUNER_STEREO_ON | The tuner is seeing stereo audio |
-
VIDEO_TUNER_RDS_ON | The tuner is seeing a RDS datastream |
-
VIDEO_TUNER_MBS_ON | The tuner is seeing a MBS datastream |
-
-
-The following modes are defined
-
-
-VIDEO_MODE_PAL | The tuner is in PAL mode |
-
VIDEO_MODE_NTSC | The tuner is in NTSC mode |
-
VIDEO_MODE_SECAM | The tuner is in SECAM mode |
-
VIDEO_MODE_AUTO | The tuner auto switches, or mode does not apply |
-
-
-Tuning frequencies are an unsigned 32bit value in 1/16th MHz or if the
-VIDEO_TUNER_LOW flag is set they are in 1/16th KHz. The current
-frequency is obtained as an unsigned long via the VIDIOCGFREQ ioctl and
-set by the VIDIOCSFREQ ioctl.
-
-
Audio
-TV and Radio devices have one or more audio inputs that may be selected.
-The audio properties are queried by passing a struct video_audio to VIDIOCGAUDIO ioctl. The
-VIDIOCSAUDIO ioctl sets audio properties.
-
-The structure contains the following fields
-
-
-audio | The channel number |
-
volume | The volume level |
-
bass | The bass level |
-
treble | The treble level |
-
flags | Flags describing the audio channel |
-
name | Canonical name for the audio input |
-
mode | The mode the audio input is in |
-
balance | The left/right balance |
-
step | Actual step used by the hardware |
-
-
-The following flags are defined
-
-
-VIDEO_AUDIO_MUTE | The audio is muted |
-
VIDEO_AUDIO_MUTABLE | Audio muting is supported |
-
VIDEO_AUDIO_VOLUME | The volume is controllable |
-
VIDEO_AUDIO_BASS | The bass is controllable |
-
VIDEO_AUDIO_TREBLE | The treble is controllable |
-
VIDEO_AUDIO_BALANCE | The balance is controllable |
-
-
-The following decoding modes are defined
-
-
-VIDEO_SOUND_MONO | Mono signal |
-
VIDEO_SOUND_STEREO | Stereo signal (NICAM for TV) |
-
VIDEO_SOUND_LANG1 | European TV alternate language 1 |
-
VIDEO_SOUND_LANG2 | European TV alternate language 2 |
-
-
-
Reading Images
-Each call to the read syscall returns the next available image
-from the device. It is up to the caller to set format and size (using
-the VIDIOCSPICT and VIDIOCSWIN ioctls) and then to pass a suitable
-size buffer and length to the function. Not all devices will support
-read operations.
-
-A second way to handle image capture is via the mmap interface if supported.
-To use the mmap interface a user first sets the desired image size and depth
-properties. Next the VIDIOCGMBUF ioctl is issued. This reports the size
-of buffer to mmap and the offset within the buffer for each frame. The
-number of frames supported is device dependent and may only be one.
-
-The video_mbuf structure contains the following fields
-
-
-size | The number of bytes to map |
-
frames | The number of frames |
-
offsets | The offset of each frame |
-
-
-Once the mmap has been made the VIDIOCMCAPTURE ioctl starts the
-capture to a frame using the format and image size specified in the
-video_mmap (which should match or be below the initial query size).
-When the VIDIOCMCAPTURE ioctl returns the frame is not
-captured yet, the driver just instructed the hardware to start the
-capture. The application has to use the VIDIOCSYNC ioctl to wait
-until the capture of a frame is finished. VIDIOCSYNC takes the frame
-number you want to wait for as argument.
-
-It is allowed to call VIDIOCMCAPTURE multiple times (with different
-frame numbers in video_mmap->frame of course) and thus have multiple
-outstanding capture requests. A simple way do to double-buffering
-using this feature looks like this:
-
-/* setup everything */
-VIDIOCMCAPTURE(0)
-while (whatever) {
- VIDIOCMCAPTURE(1)
- VIDIOCSYNC(0)
- /* process frame 0 while the hardware captures frame 1 */
- VIDIOCMCAPTURE(0)
- VIDIOCSYNC(1)
- /* process frame 1 while the hardware captures frame 0 */
-}
-
-Note that you are not limited to only two frames. The API
-allows up to 32 frames, the VIDIOCGMBUF ioctl returns the number of
-frames the driver granted. Thus it is possible to build deeper queues
-to avoid loosing frames on load peaks.
-
-While capturing to memory the driver will make a "best effort" attempt
-to capture to screen as well if requested. This normally means all
-frames that "miss" memory mapped capture will go to the display.
-
-A final ioctl exists to allow a device to obtain related devices if a
-driver has multiple components (for example video0 may not be associated
-with vbi0 which would cause an intercast display program to make a bad
-mistake). The VIDIOCGUNIT ioctl reports the unit numbers of the associated
-devices if any exist. The video_unit structure has the following fields.
-
-
-video | Video capture device |
-
vbi | VBI capture device |
-
radio | Radio device |
-
audio | Audio mixer |
-
teletext | Teletext device |
-
-
-
RDS Datastreams
-For radio devices that support it, it is possible to receive Radio Data
-System (RDS) data by means of a read() on the device. The data is packed in
-groups of three, as follows:
-
-First Octet | Least Significant Byte of RDS Block |
-Second Octet | Most Significant Byte of RDS Block
- |
Third Octet | Bit 7: | Error bit. Indicates that
-an uncorrectable error occurred during reception of this block. |
- | Bit 6: | Corrected bit. Indicates that
-an error was corrected for this data block. |
- | Bits 5-3: | Received Offset. Indicates the
-offset received by the sync system. |
- | Bits 2-0: | Offset Name. Indicates the
-offset applied to this data. |
-
-
-
+V4L API
+Video For Linux APIs
+
diff --git a/Documentation/video4linux/CARDLIST.bttv b/Documentation/video4linux/CARDLIST.bttv
index e46761c39e3f..aeeafec0594c 100644
--- a/Documentation/video4linux/CARDLIST.bttv
+++ b/Documentation/video4linux/CARDLIST.bttv
@@ -119,3 +119,17 @@ card=117 - NGS NGSTV+
card=118 - LMLBT4
card=119 - Tekram M205 PRO
card=120 - Conceptronic CONTVFMi
+card=121 - Euresys Picolo Tetra
+card=122 - Spirit TV Tuner
+card=123 - AVerMedia AVerTV DVB-T 771
+card=124 - AverMedia AverTV DVB-T 761
+card=125 - MATRIX Vision Sigma-SQ
+card=126 - MATRIX Vision Sigma-SLC
+card=127 - APAC Viewcomp 878(AMAX)
+card=128 - DVICO FusionHDTV DVB-T Lite
+card=129 - V-Gear MyVCD
+card=130 - Super TV Tuner
+card=131 - Tibet Systems 'Progress DVR' CS16
+card=132 - Kodicom 4400R (master)
+card=133 - Kodicom 4400R (slave)
+card=134 - Adlink RTV24
diff --git a/Documentation/video4linux/CARDLIST.cx88 b/Documentation/video4linux/CARDLIST.cx88
new file mode 100644
index 000000000000..4377aa11f567
--- /dev/null
+++ b/Documentation/video4linux/CARDLIST.cx88
@@ -0,0 +1,29 @@
+card=0 - UNKNOWN/GENERIC
+card=1 - Hauppauge WinTV 34xxx models
+card=2 - GDI Black Gold
+card=3 - PixelView
+card=4 - ATI TV Wonder Pro
+card=5 - Leadtek Winfast 2000XP Expert
+card=6 - AverTV Studio 303 (M126)
+card=7 - MSI TV-@nywhere Master
+card=8 - Leadtek Winfast DV2000
+card=9 - Leadtek PVR 2000
+card=10 - IODATA GV-VCP3/PCI
+card=11 - Prolink PlayTV PVR
+card=12 - ASUS PVR-416
+card=13 - MSI TV-@nywhere
+card=14 - KWorld/VStream XPert DVB-T
+card=15 - DViCO FusionHDTV DVB-T1
+card=16 - KWorld LTV883RF
+card=17 - DViCO FusionHDTV 3 Gold-Q
+card=18 - Hauppauge Nova-T DVB-T
+card=19 - Conexant DVB-T reference design
+card=20 - Provideo PV259
+card=21 - DViCO FusionHDTV DVB-T Plus
+card=22 - digitalnow DNTV Live! DVB-T
+card=23 - pcHDTV HD3000 HDTV
+card=24 - Hauppauge WinTV 28xxx (Roslyn) models
+card=25 - Digital-Logic MICROSPACE Entertainment Center (MEC)
+card=26 - IODATA GV/BCTV7E
+card=27 - PixelView PlayTV Ultra Pro (Stereo)
+card=28 - DViCO FusionHDTV 3 Gold-T
diff --git a/Documentation/video4linux/CARDLIST.saa7134 b/Documentation/video4linux/CARDLIST.saa7134
index a6c82fa4de02..735e8ba02d9f 100644
--- a/Documentation/video4linux/CARDLIST.saa7134
+++ b/Documentation/video4linux/CARDLIST.saa7134
@@ -20,16 +20,43 @@
19 -> Compro VideoMate TV [185b:c100]
20 -> Matrox CronosPlus [102B:48d0]
21 -> 10MOONS PCI TV CAPTURE CARD [1131:2001]
- 22 -> Medion 2819/ AverMedia M156 [1461:a70b,1461:2115]
+ 22 -> AverMedia M156 / Medion 2819 [1461:a70b]
23 -> BMK MPEX Tuner
24 -> KNC One TV-Station DVR [1894:a006]
25 -> ASUS TV-FM 7133 [1043:4843]
26 -> Pinnacle PCTV Stereo (saa7134) [11bd:002b]
- 27 -> Manli MuchTV M-TV002
- 28 -> Manli MuchTV M-TV001
+ 27 -> Manli MuchTV M-TV002/Behold TV 403 FM
+ 28 -> Manli MuchTV M-TV001/Behold TV 401
29 -> Nagase Sangyo TransGear 3000TV [1461:050c]
30 -> Elitegroup ECS TVP3XP FM1216 Tuner Card(PAL-BG,FM) [1019:4cb4]
31 -> Elitegroup ECS TVP3XP FM1236 Tuner Card (NTSC,FM) [1019:4cb5]
32 -> AVACS SmartTV
33 -> AVerMedia DVD EZMaker [1461:10ff]
- 34 -> LifeView FlyTV Platinum33 mini [5168:0212]
+ 34 -> Noval Prime TV 7133
+ 35 -> AverMedia AverTV Studio 305 [1461:2115]
+ 37 -> Items MuchTV Plus / IT-005
+ 38 -> Terratec Cinergy 200 TV [153B:1152]
+ 39 -> LifeView FlyTV Platinum Mini [5168:0212]
+ 40 -> Compro VideoMate TV PVR/FM [185b:c100]
+ 41 -> Compro VideoMate TV Gold+ [185b:c100]
+ 42 -> Sabrent SBT-TVFM (saa7130)
+ 43 -> :Zolid Xpert TV7134
+ 44 -> Empire PCI TV-Radio LE
+ 45 -> Avermedia AVerTV Studio 307 [1461:9715]
+ 46 -> AVerMedia Cardbus TV/Radio [1461:d6ee]
+ 47 -> Terratec Cinergy 400 mobile [153b:1162]
+ 48 -> Terratec Cinergy 600 TV MK3 [153B:1158]
+ 49 -> Compro VideoMate Gold+ Pal [185b:c200]
+ 50 -> Pinnacle PCTV 300i DVB-T + PAL [11bd:002d]
+ 51 -> ProVideo PV952 [1540:9524]
+ 52 -> AverMedia AverTV/305 [1461:2108]
+ 54 -> LifeView FlyTV Platinum FM [5168:0214,1489:0214]
+ 55 -> LifeView FlyDVB-T DUO [5168:0306]
+ 56 -> Avermedia AVerTV 307 [1461:a70a]
+ 57 -> Avermedia AVerTV GO 007 FM [1461:f31f]
+ 58 -> ADS Tech Instant TV (saa7135) [1421:0350,1421:0370]
+ 59 -> Kworld/Tevion V-Stream Xpert TV PVR7134
+ 60 -> Typhoon DVB-T Duo Digital/Analog Cardbus
+ 61 -> Philips TOUGH DVB-T reference design
+ 62 -> Compro VideoMate TV Gold+II
+ 63 -> Kworld Xpert TV PVR7134
diff --git a/Documentation/video4linux/CARDLIST.tuner b/Documentation/video4linux/CARDLIST.tuner
index f7bafe862ba0..e78020f68b2e 100644
--- a/Documentation/video4linux/CARDLIST.tuner
+++ b/Documentation/video4linux/CARDLIST.tuner
@@ -44,3 +44,21 @@ tuner=42 - Philips 1236D ATSC/NTSC daul in
tuner=43 - Philips NTSC MK3 (FM1236MK3 or FM1236/F)
tuner=44 - Philips 4 in 1 (ATI TV Wonder Pro/Conexant)
tuner=45 - Microtune 4049 FM5
+tuner=46 - Panasonic VP27s/ENGE4324D
+tuner=47 - LG NTSC (TAPE series)
+tuner=48 - Tenna TNF 8831 BGFF)
+tuner=49 - Microtune 4042 FI5 ATSC/NTSC dual in
+tuner=50 - TCL 2002N
+tuner=51 - Philips PAL/SECAM_D (FM 1256 I-H3)
+tuner=52 - Thomson DDT 7610 (ATSC/NTSC)
+tuner=53 - Philips FQ1286
+tuner=54 - tda8290+75
+tuner=55 - LG PAL (TAPE series)
+tuner=56 - Philips PAL/SECAM multi (FQ1216AME MK4)
+tuner=57 - Philips FQ1236A MK4
+tuner=58 - Ymec TVision TVF-8531MF
+tuner=59 - Ymec TVision TVF-5533MF
+tuner=60 - Thomson DDT 7611 (ATSC/NTSC)
+tuner=61 - Tena TNF9533-D/IF
+tuner=62 - Philips TEA5767HN FM Radio
+tuner=63 - Philips FMD1216ME MK3 Hybrid Tuner
diff --git a/Documentation/video4linux/README.saa7134 b/Documentation/video4linux/README.saa7134
index 1a446c65365e..1f788e498eff 100644
--- a/Documentation/video4linux/README.saa7134
+++ b/Documentation/video4linux/README.saa7134
@@ -57,6 +57,15 @@ Cards can use either of these two crystals (xtal):
- 24.576MHz -> .audio_clock=0x200000
(xtal * .audio_clock = 51539600)
+Some details about 30/34/35:
+
+ - saa7130 - low-price chip, doesn't have mute, that is why all those
+ cards should have .mute field defined in their tuner structure.
+
+ - saa7134 - usual chip
+
+ - saa7133/35 - saa7135 is probably a marketing decision, since all those
+ chips identifies itself as 33 on pci.
Credits
=======
diff --git a/Documentation/video4linux/hauppauge-wintv-cx88-ir.txt b/Documentation/video4linux/hauppauge-wintv-cx88-ir.txt
new file mode 100644
index 000000000000..93fec32a1188
--- /dev/null
+++ b/Documentation/video4linux/hauppauge-wintv-cx88-ir.txt
@@ -0,0 +1,54 @@
+The controls for the mux are GPIO [0,1] for source, and GPIO 2 for muting.
+
+GPIO0 GPIO1
+ 0 0 TV Audio
+ 1 0 FM radio
+ 0 1 Line-In
+ 1 1 Mono tuner bypass or CD passthru (tuner specific)
+
+GPIO 16(i believe) is tied to the IR port (if present).
+
+------------------------------------------------------------------------------------
+
+>From the data sheet:
+ Register 24'h20004 PCI Interrupt Status
+ bit [18] IR_SMP_INT Set when 32 input samples have been collected over
+ gpio[16] pin into GP_SAMPLE register.
+
+What's missing from the data sheet:
+
+Setup 4KHz sampling rate (roughly 2x oversampled; good enough for our RC5
+compat remote)
+set register 0x35C050 to 0xa80a80
+
+enable sampling
+set register 0x35C054 to 0x5
+
+Of course, enable the IRQ bit 18 in the interrupt mask register .(and
+provide for a handler)
+
+GP_SAMPLE register is at 0x35C058
+
+Bits are then right shifted into the GP_SAMPLE register at the specified
+rate; you get an interrupt when a full DWORD is recieved.
+You need to recover the actual RC5 bits out of the (oversampled) IR sensor
+bits. (Hint: look for the 0/1and 1/0 crossings of the RC5 bi-phase data) An
+actual raw RC5 code will span 2-3 DWORDS, depending on the actual alignment.
+
+I'm pretty sure when no IR signal is present the receiver is always in a
+marking state(1); but stray light, etc can cause intermittent noise values
+as well. Remember, this is a free running sample of the IR receiver state
+over time, so don't assume any sample starts at any particular place.
+
+http://www.atmel.com/dyn/resources/prod_documents/doc2817.pdf
+This data sheet (google search) seems to have a lovely description of the
+RC5 basics
+
+http://users.pandora.be/nenya/electronics/rc5/ and more data
+
+http://www.ee.washington.edu/circuit_archive/text/ir_decode.txt
+and even a reference to how to decode a bi-phase data stream.
+
+http://www.xs4all.nl/~sbp/knowledge/ir/rc5.htm
+still more info
+
diff --git a/Documentation/video4linux/lifeview.txt b/Documentation/video4linux/lifeview.txt
new file mode 100644
index 000000000000..b07ea79c2b7e
--- /dev/null
+++ b/Documentation/video4linux/lifeview.txt
@@ -0,0 +1,42 @@
+collecting data about the lifeview models and the config coding on
+gpio pins 0-9 ...
+==================================================================
+
+bt878:
+ LR50 rev. Q ("PARTS: 7031505116), Tuner wurde als Nr. 5 erkannt, Eingänge
+ SVideo, TV, Composite, Audio, Remote. CP9..1=100001001 (1: 0-Ohm-Widerstand
+ gegen GND unbestückt; 0: bestückt)
+
+------------------------------------------------------------------------------
+
+saa7134:
+ /* LifeView FlyTV Platinum FM (LR214WF) */
+ /* "Peter Missel */
+ .name = "LifeView FlyTV Platinum FM",
+ /* GP27 MDT2005 PB4 pin 10 */
+ /* GP26 MDT2005 PB3 pin 9 */
+ /* GP25 MDT2005 PB2 pin 8 */
+ /* GP23 MDT2005 PB1 pin 7 */
+ /* GP22 MDT2005 PB0 pin 6 */
+ /* GP21 MDT2005 PB5 pin 11 */
+ /* GP20 MDT2005 PB6 pin 12 */
+ /* GP19 MDT2005 PB7 pin 13 */
+ /* nc MDT2005 PA3 pin 2 */
+ /* Remote MDT2005 PA2 pin 1 */
+ /* GP18 MDT2005 PA1 pin 18 */
+ /* nc MDT2005 PA0 pin 17 strap low */
+
+ /* GP17 Strap "GP7"=High */
+ /* GP16 Strap "GP6"=High
+ 0=Radio 1=TV
+ Drives SA630D ENCH1 and HEF4052 A1 pins
+ to do FM radio through SIF input */
+ /* GP15 nc */
+ /* GP14 nc */
+ /* GP13 nc */
+ /* GP12 Strap "GP5" = High */
+ /* GP11 Strap "GP4" = High */
+ /* GP10 Strap "GP3" = High */
+ /* GP09 Strap "GP2" = Low */
+ /* GP08 Strap "GP1" = Low */
+ /* GP07.00 nc */
diff --git a/Documentation/video4linux/not-in-cx2388x-datasheet.txt b/Documentation/video4linux/not-in-cx2388x-datasheet.txt
new file mode 100644
index 000000000000..96b638b5ba1d
--- /dev/null
+++ b/Documentation/video4linux/not-in-cx2388x-datasheet.txt
@@ -0,0 +1,37 @@
+=================================================================================
+MO_OUTPUT_FORMAT (0x310164)
+
+ Previous default from DScaler: 0x1c1f0008
+ Digit 8: 31-28
+ 28: PREVREMOD = 1
+
+ Digit 7: 27-24 (0xc = 12 = b1100 )
+ 27: COMBALT = 1
+ 26: PAL_INV_PHASE
+ (DScaler apparently set this to 1, resulted in sucky picture)
+
+ Digits 6,5: 23-16
+ 25-16: COMB_RANGE = 0x1f [default] (9 bits -> max 512)
+
+ Digit 4: 15-12
+ 15: DISIFX = 0
+ 14: INVCBF = 0
+ 13: DISADAPT = 0
+ 12: NARROWADAPT = 0
+
+ Digit 3: 11-8
+ 11: FORCE2H
+ 10: FORCEREMD
+ 9: NCHROMAEN
+ 8: NREMODEN
+
+ Digit 2: 7-4
+ 7-6: YCORE
+ 5-4: CCORE
+
+ Digit 1: 3-0
+ 3: RANGE = 1
+ 2: HACTEXT
+ 1: HSFMT
+
+=================================================================================
diff --git a/Documentation/w1/w1.generic b/Documentation/w1/w1.generic
index eace3046a858..f937fbe1cacb 100644
--- a/Documentation/w1/w1.generic
+++ b/Documentation/w1/w1.generic
@@ -1,19 +1,92 @@
-Any w1 device must be connected to w1 bus master device - for example
-ds9490 usb device or w1-over-GPIO or RS232 converter.
-Driver for w1 bus master must provide several functions(you can find
-them in struct w1_bus_master definition in w1.h) which then will be
-called by w1 core to send various commands over w1 bus(by default it is
-reset and search commands). When some device is found on the bus, w1 core
-checks if driver for it's family is loaded.
-If driver is loaded w1 core creates new w1_slave object and registers it
-in the system(creates some generic sysfs files(struct w1_family_ops in
-w1_family.h), notifies any registered listener and so on...).
-It is device driver's business to provide any communication method
-upstream.
-For example w1_therm driver(ds18?20 thermal sensor family driver)
-provides temperature reading function which is bound to ->rbin() method
-of the above w1_family_ops structure.
-w1_smem - driver for simple 64bit memory cell provides ID reading
-method.
+The 1-wire (w1) subsystem
+------------------------------------------------------------------
+The 1-wire bus is a simple master-slave bus that communicates via a single
+signal wire (plus ground, so two wires).
+
+Devices communicate on the bus by pulling the signal to ground via an open
+drain output and by sampling the logic level of the signal line.
+
+The w1 subsystem provides the framework for managing w1 masters and
+communication with slaves.
+
+All w1 slave devices must be connected to a w1 bus master device.
+
+Example w1 master devices:
+ DS9490 usb device
+ W1-over-GPIO
+ DS2482 (i2c to w1 bridge)
+ Emulated devices, such as a RS232 converter, parallel port adapter, etc
+
+
+What does the w1 subsystem do?
+------------------------------------------------------------------
+When a w1 master driver registers with the w1 subsystem, the following occurs:
+
+ - sysfs entries for that w1 master are created
+ - the w1 bus is periodically searched for new slave devices
+
+When a device is found on the bus, w1 core checks if driver for it's family is
+loaded. If so, the family driver is attached to the slave.
+If there is no driver for the family, a simple sysfs entry is created
+for the slave device.
+
+
+W1 device families
+------------------------------------------------------------------
+Slave devices are handled by a driver written for a family of w1 devices.
+
+A family driver populates a struct w1_family_ops (see w1_family.h) and
+registers with the w1 subsystem.
+
+Current family drivers:
+w1_therm - (ds18?20 thermal sensor family driver)
+ provides temperature reading function which is bound to ->rbin() method
+ of the above w1_family_ops structure.
+
+w1_smem - driver for simple 64bit memory cell provides ID reading method.
You can call above methods by reading appropriate sysfs files.
+
+
+What does a w1 master driver need to implement?
+------------------------------------------------------------------
+
+The driver for w1 bus master must provide at minimum two functions.
+
+Emulated devices must provide the ability to set the output signal level
+(write_bit) and sample the signal level (read_bit).
+
+Devices that support the 1-wire natively must provide the ability to write and
+sample a bit (touch_bit) and reset the bus (reset_bus).
+
+Most hardware provides higher-level functions that offload w1 handling.
+See struct w1_bus_master definition in w1.h for details.
+
+
+w1 master sysfs interface
+------------------------------------------------------------------
+ - a directory for a found device. The format is family-serial
+bus - (standard) symlink to the w1 bus
+driver - (standard) symlink to the w1 driver
+w1_master_attempts - the number of times a search was attempted
+w1_master_max_slave_count
+ - the maximum slaves that may be attached to a master
+w1_master_name - the name of the device (w1_bus_masterX)
+w1_master_search - the number of searches left to do, -1=continual (default)
+w1_master_slave_count
+ - the number of slaves found
+w1_master_slaves - the names of the slaves, one per line
+w1_master_timeout - the delay in seconds between searches
+
+If you have a w1 bus that never changes (you don't add or remove devices),
+you can set w1_master_search to a positive value to disable searches.
+
+
+w1 slave sysfs interface
+------------------------------------------------------------------
+bus - (standard) symlink to the w1 bus
+driver - (standard) symlink to the w1 driver
+name - the device name, usually the same as the directory name
+w1_slave - (optional) a binary file whose meaning depends on the
+ family driver
+
diff --git a/MAINTAINERS b/MAINTAINERS
index 10ca899693db..aa1d9d702e2d 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -194,7 +194,7 @@ S: Maintained
ADM1025 HARDWARE MONITOR DRIVER
P: Jean Delvare
M: khali@linux-fr.org
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Maintained
ADT746X FAN DRIVER
@@ -242,7 +242,7 @@ S: Maintained
ALI1563 I2C DRIVER
P: Rudolf Marek
M: r.marek@sh.cvut.cz
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Maintained
ALPHA PORT
@@ -265,6 +265,11 @@ P: Arnaldo Carvalho de Melo
M: acme@conectiva.com.br
S: Maintained
+ARC FRAMEBUFFER DRIVER
+P: Jaya Kumar
+M: jayalk@intworks.biz
+S: Maintained
+
ARM26 ARCHITECTURE
P: Ian Molton
M: spyro@f2s.com
@@ -299,7 +304,7 @@ S: Maintained
ARM/PT DIGITAL BOARD PORT
P: Stefan Eletzhofer
M: stefan.eletzhofer@eletztrick.de
-L: linux-arm-kernel@lists.arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
W: http://www.arm.linux.org.uk/
S: Maintained
@@ -312,21 +317,21 @@ S: Maintained
ARM/STRONGARM110 PORT
P: Russell King
M: rmk@arm.linux.org.uk
-L: linux-arm-kernel@lists.arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
W: http://www.arm.linux.org.uk/
S: Maintained
ARM/S3C2410 ARM ARCHITECTURE
P: Ben Dooks
M: ben-s3c2410@fluff.org
-L: linux-arm-kernel@lists.arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
W: http://www.fluff.org/ben/linux/
S: Maintained
ARM/S3C2440 ARM ARCHITECTURE
P: Ben Dooks
M: ben-s3c2440@fluff.org
-L: linux-arm-kernel@lists.arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
W: http://www.fluff.org/ben/linux/
S: Maintained
@@ -506,12 +511,19 @@ L: bonding-devel@lists.sourceforge.net
W: http://sourceforge.net/projects/bonding/
S: Supported
+BROADBAND PROCESSOR ARCHITECTURE
+P: Arnd Bergmann
+M: arnd@arndb.de
+L: linuxppc64-dev@ozlabs.org
+W: http://linuxppc64.org
+S: Supported
+
BTTV VIDEO4LINUX DRIVER
-P: Gerd Knorr
-M: kraxel@bytesex.org
+P: Mauro Carvalho Chehab
+M: mchehab@brturbo.com.br
L: video4linux-list@redhat.com
-W: http://bytesex.org/bttv/
-S: Orphan
+W: http://linuxtv.org
+S: Maintained
BUSLOGIC SCSI DRIVER
P: Leonard N. Zubkoff
@@ -571,10 +583,9 @@ S: Supported
COMPUTONE INTELLIPORT MULTIPORT CARD
P: Michael H. Warfield
-M: Michael H. Warfield
+M: mhw@wittsend.com
W: http://www.wittsend.com/computone.html
-L: linux-computone@lazuli.wittsend.com
-S: Orphaned
+S: Maintained
COSA/SRP SYNC SERIAL DRIVER
P: Jan "Yenya" Kasprzak
@@ -1004,7 +1015,7 @@ P: Greg Kroah-Hartman
M: greg@kroah.com
P: Jean Delvare
M: khali@linux-fr.org
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
W: http://www.lm-sensors.nu/
S: Maintained
@@ -1145,7 +1156,7 @@ S: Maintained
INFINIBAND SUBSYSTEM
P: Roland Dreier
-M: roland@topspin.com
+M: rolandd@cisco.com
P: Sean Hefty
M: mshefty@ichips.intel.com
P: Hal Rosenstock
@@ -1325,6 +1336,16 @@ M: rml@novell.com
L: linux-kernel@vger.kernel.org
S: Maintained
+KEXEC
+P: Eric Biederman
+P: Randy Dunlap
+M: ebiederm@xmission.com
+M: rddunlap@osdl.org
+W: http://www.xmission.com/~ebiederm/files/kexec/
+L: linux-kernel@vger.kernel.org
+L: fastboot@osdl.org
+S: Maintained
+
LANMEDIA WAN CARD DRIVER
P: Andrew Stanley-Jones
M: asj@lanmedia.com
@@ -1432,13 +1453,13 @@ S: Supported
LM83 HARDWARE MONITOR DRIVER
P: Jean Delvare
M: khali@linux-fr.org
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Maintained
LM90 HARDWARE MONITOR DRIVER
P: Jean Delvare
M: khali@linux-fr.org
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Maintained
LOGICAL DISK MANAGER SUPPORT (LDM, Windows 2000/XP Dynamic Disks)
@@ -1855,7 +1876,7 @@ S: Maintained
PXA2xx SUPPORT
P: Nicolas Pitre
M: nico@cam.org
-L: linux-arm-kernel@lists.arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
QLOGIC QLA2XXX FC-SCSI DRIVER
@@ -2077,7 +2098,7 @@ S: Maintained
SMSC47M1 HARDWARE MONITOR DRIVER
P: Jean Delvare
M: khali@linux-fr.org
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Odd Fixes
SMB FILESYSTEM
@@ -2110,9 +2131,7 @@ S: Maintained
SOFTWARE SUSPEND:
P: Pavel Machek
M: pavel@suse.cz
-M: pavel@ucw.cz
-L: http://lister.fornax.hu/mailman/listinfo/swsusp
-W: http://swsusp.sf.net/
+L: linux-pm@osdl.org
S: Maintained
SONIC NETWORK DRIVER
@@ -2140,6 +2159,11 @@ W: http://tpmdd.sourceforge.net
L: tpmdd-devel@lists.sourceforge.net
S: Maintained
+TENSILICA XTENSA PORT (xtensa):
+P: Chris Zankel
+M: chris@zankel.net
+S: Maintained
+
UltraSPARC (sparc64):
P: David S. Miller
M: davem@davemloft.net
@@ -2157,7 +2181,7 @@ SHARP LH SUPPORT (LH7952X & LH7A40X)
P: Marc Singer
M: elf@buici.com
W: http://projects.buici.com/arm
-L: linux-arm-kernel@lists.arm.linux.org.uk
+L: linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
S: Maintained
SPARC (sparc32):
@@ -2584,7 +2608,7 @@ M: davidm@snapgear.com
P: D. Jeff Dionne (created first uClinux port)
M: jeff@uclinux.org
W: http://www.uclinux.org/
-L: uclinux-dev@uclinux.org
+L: uclinux-dev@uclinux.org (subscribers-only)
S: Maintained
UCLINUX FOR NEC V850
@@ -2608,15 +2632,16 @@ W: http://rio500.sourceforge.net
S: Maintained
VIDEO FOR LINUX
-P: Gerd Knorr
-M: kraxel@bytesex.org
+P: Mauro Carvalho Chehab
+M: mchehab@brturbo.com.br
L: video4linux-list@redhat.com
-S: Orphan
+W: http://linuxtv.org
+S: Maintained
W1 DALLAS'S 1-WIRE BUS
P: Evgeniy Polyakov
M: johnpol@2ka.mipt.ru
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Maintained
W83L51xD SD/MMC CARD INTERFACE DRIVER
@@ -2629,7 +2654,7 @@ S: Maintained
W83L785TS HARDWARE MONITOR DRIVER
P: Jean Delvare
M: khali@linux-fr.org
-L: sensors@stimpy.netroedge.com
+L: lm-sensors@lm-sensors.org
S: Odd Fixes
WAN ROUTER & SANGOMA WANPIPE DRIVERS & API (X.25, FRAME RELAY, PPP, CISCO HDLC)
diff --git a/Makefile b/Makefile
index 0d1e74d50067..77aab7bdde01 100644
--- a/Makefile
+++ b/Makefile
@@ -1,7 +1,7 @@
VERSION = 2
PATCHLEVEL = 6
-SUBLEVEL = 12
-EXTRAVERSION =
+SUBLEVEL = 13
+EXTRAVERSION =-rc1
NAME=Woozy Numbat
# *DOCUMENTATION*
@@ -281,7 +281,7 @@ export quiet Q KBUILD_VERBOSE
# See documentation in Documentation/kbuild/makefiles.txt
# cc-option
-# Usage: cflags-y += $(call gcc-option, -march=winchip-c6, -march=i586)
+# Usage: cflags-y += $(call cc-option, -march=winchip-c6, -march=i586)
cc-option = $(shell if $(CC) $(CFLAGS) $(1) -S -o /dev/null -xc /dev/null \
> /dev/null 2>&1; then echo "$(1)"; else echo "$(2)"; fi ;)
@@ -518,7 +518,7 @@ CFLAGS += $(call add-align,CONFIG_CC_ALIGN_LOOPS,-loops)
CFLAGS += $(call add-align,CONFIG_CC_ALIGN_JUMPS,-jumps)
ifdef CONFIG_FRAME_POINTER
-CFLAGS += -fno-omit-frame-pointer
+CFLAGS += -fno-omit-frame-pointer $(call cc-option,-fno-optimize-sibling-calls,)
else
CFLAGS += -fomit-frame-pointer
endif
diff --git a/arch/alpha/Kconfig b/arch/alpha/Kconfig
index f7c96635d3b4..c5739d6309df 100644
--- a/arch/alpha/Kconfig
+++ b/arch/alpha/Kconfig
@@ -509,7 +509,7 @@ config NR_CPUS
depends on SMP
default "64"
-config DISCONTIGMEM
+config ARCH_DISCONTIGMEM_ENABLE
bool "Discontiguous Memory Support (EXPERIMENTAL)"
depends on EXPERIMENTAL
help
@@ -518,6 +518,8 @@ config DISCONTIGMEM
or have huge holes in the physical address space for other reasons.
See for more.
+source "mm/Kconfig"
+
config NUMA
bool "NUMA Support (EXPERIMENTAL)"
depends on DISCONTIGMEM
diff --git a/arch/alpha/defconfig b/arch/alpha/defconfig
index 5e39b7a7c8f4..6da9c3dbde44 100644
--- a/arch/alpha/defconfig
+++ b/arch/alpha/defconfig
@@ -96,7 +96,7 @@ CONFIG_ALPHA_CORE_AGP=y
CONFIG_ALPHA_BROKEN_IRQ_MASK=y
CONFIG_EISA=y
# CONFIG_SMP is not set
-# CONFIG_DISCONTIGMEM is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
CONFIG_VERBOSE_MCHECK=y
CONFIG_VERBOSE_MCHECK_ON=1
CONFIG_PCI_LEGACY_PROC=y
diff --git a/arch/alpha/kernel/irq_alpha.c b/arch/alpha/kernel/irq_alpha.c
index e6ded33c6e22..9d34ce26e5ef 100644
--- a/arch/alpha/kernel/irq_alpha.c
+++ b/arch/alpha/kernel/irq_alpha.c
@@ -55,6 +55,8 @@ do_entInt(unsigned long type, unsigned long vector,
#ifdef CONFIG_SMP
{
long cpu;
+
+ local_irq_disable();
smp_percpu_timer_interrupt(regs);
cpu = smp_processor_id();
if (cpu != boot_cpuid) {
diff --git a/arch/alpha/kernel/traps.c b/arch/alpha/kernel/traps.c
index fd7bd17cc960..6f509a644bdd 100644
--- a/arch/alpha/kernel/traps.c
+++ b/arch/alpha/kernel/traps.c
@@ -240,7 +240,7 @@ do_entIF(unsigned long type, struct pt_regs *regs)
siginfo_t info;
int signo, code;
- if (regs->ps == 0) {
+ if ((regs->ps & ~IPL_MAX) == 0) {
if (type == 1) {
const unsigned int *data
= (const unsigned int *) regs->pc;
diff --git a/arch/alpha/mm/numa.c b/arch/alpha/mm/numa.c
index ba81c4422aaf..c7481d59b6df 100644
--- a/arch/alpha/mm/numa.c
+++ b/arch/alpha/mm/numa.c
@@ -327,8 +327,6 @@ void __init mem_init(void)
extern char _text, _etext, _data, _edata;
extern char __init_begin, __init_end;
unsigned long nid, i;
- struct page * lmem_map;
-
high_memory = (void *) __va(max_low_pfn << PAGE_SHIFT);
reservedpages = 0;
@@ -338,10 +336,10 @@ void __init mem_init(void)
*/
totalram_pages += free_all_bootmem_node(NODE_DATA(nid));
- lmem_map = node_mem_map(nid);
pfn = NODE_DATA(nid)->node_start_pfn;
for (i = 0; i < node_spanned_pages(nid); i++, pfn++)
- if (page_is_ram(pfn) && PageReserved(lmem_map+i))
+ if (page_is_ram(pfn) &&
+ PageReserved(nid_page_nr(nid, i)))
reservedpages++;
}
@@ -373,18 +371,18 @@ show_mem(void)
show_free_areas();
printk("Free swap: %6ldkB\n", nr_swap_pages<<(PAGE_SHIFT-10));
for_each_online_node(nid) {
- struct page * lmem_map = node_mem_map(nid);
i = node_spanned_pages(nid);
while (i-- > 0) {
+ struct page *page = nid_page_nr(nid, i);
total++;
- if (PageReserved(lmem_map+i))
+ if (PageReserved(page))
reserved++;
- else if (PageSwapCache(lmem_map+i))
+ else if (PageSwapCache(page))
cached++;
- else if (!page_count(lmem_map+i))
+ else if (!page_count(page))
free++;
else
- shared += page_count(lmem_map + i) - 1;
+ shared += page_count(page) - 1;
}
}
printk("%ld pages of RAM\n",total);
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 475950c8a831..620f2ca94ed2 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -67,10 +67,6 @@ config GENERIC_BUST_SPINLOCK
config GENERIC_ISA_DMA
bool
-config GENERIC_IOMAP
- bool
- default y
-
config FIQ
bool
@@ -161,7 +157,7 @@ config ARCH_RPC
config ARCH_SA1100
bool "SA1100-based"
select ISA
- select DISCONTIGMEM
+ select ARCH_DISCONTIGMEM_ENABLE
config ARCH_S3C2410
bool "Samsung S3C2410"
@@ -202,6 +198,11 @@ config ARCH_H720X
help
This enables support for systems based on the Hynix HMS720x
+config ARCH_AAEC2000
+ bool "Agilent AAEC-2000 based"
+ help
+ This enables support for systems based on the Agilent AAEC-2000
+
endchoice
source "arch/arm/mach-clps711x/Kconfig"
@@ -234,6 +235,8 @@ source "arch/arm/mach-h720x/Kconfig"
source "arch/arm/mach-versatile/Kconfig"
+source "arch/arm/mach-aaec2000/Kconfig"
+
# Definitions to make life easier
config ARCH_ACORN
bool
@@ -277,7 +280,7 @@ config ISA_DMA_API
default y
config PCI
- bool "PCI support" if ARCH_INTEGRATOR_AP
+ bool "PCI support" if ARCH_INTEGRATOR_AP || ARCH_VERSATILE_PB
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
@@ -343,7 +346,27 @@ config PREEMPT
Say Y here if you are building a kernel for a desktop, embedded
or real-time system. Say N if you are unsure.
-config DISCONTIGMEM
+config NO_IDLE_HZ
+ bool "Dynamic tick timer"
+ help
+ Select this option if you want to disable continuous timer ticks
+ and have them programmed to occur as required. This option saves
+ power as the system can remain in idle state for longer.
+
+ By default dynamic tick is disabled during the boot, and can be
+ manually enabled with:
+
+ echo 1 > /sys/devices/system/timer/timer0/dyn_tick
+
+ Alternatively, if you want dynamic tick automatically enabled
+ during boot, pass "dyntick=enable" via the kernel command string.
+
+ Please note that dynamic tick may affect the accuracy of
+ timekeeping on some platforms depending on the implementation.
+ Currently at least OMAP platform is known to have accurate
+ timekeeping with dynamic tick.
+
+config ARCH_DISCONTIGMEM_ENABLE
bool
default (ARCH_LH7A40X && !LH7A40X_CONTIGMEM)
help
@@ -352,6 +375,8 @@ config DISCONTIGMEM
or have huge holes in the physical address space for other reasons.
See for more.
+source "mm/Kconfig"
+
config LEDS
bool "Timer and CPU usage LEDs"
depends on ARCH_CDB89712 || ARCH_CO285 || ARCH_EBSA110 || \
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 2277e3d179cc..eb933dcafba0 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -56,7 +56,7 @@ tune-$(CONFIG_CPU_XSCALE) :=$(call cc-option,-mtune=xscale,-mtune=strongarm110)
tune-$(CONFIG_CPU_V6) :=-mtune=strongarm
# Need -Uarm for gcc < 3.x
-CFLAGS_ABI :=$(call cc-option,-mapcs-32,-mabi=apcs-gnu)
+CFLAGS_ABI :=$(call cc-option,-mapcs-32,-mabi=apcs-gnu) $(call cc-option,-mno-thumb-interwork,)
CFLAGS +=$(CFLAGS_ABI) $(arch-y) $(tune-y) $(call cc-option,-mshort-load-bytes,$(call cc-option,-malignment-traps,)) -msoft-float -Uarm
AFLAGS +=$(CFLAGS_ABI) $(arch-y) $(tune-y) -msoft-float
@@ -97,6 +97,7 @@ textaddr-$(CONFIG_ARCH_FORTUNET) := 0xc0008000
machine-$(CONFIG_ARCH_VERSATILE) := versatile
machine-$(CONFIG_ARCH_IMX) := imx
machine-$(CONFIG_ARCH_H720X) := h720x
+ machine-$(CONFIG_ARCH_AAEC2000) := aaec2000
ifeq ($(CONFIG_ARCH_EBSA110),y)
# This is what happens if you forget the IOCS16 line.
diff --git a/arch/arm/boot/install.sh b/arch/arm/boot/install.sh
index 935bb27369e9..9f9bed207345 100644
--- a/arch/arm/boot/install.sh
+++ b/arch/arm/boot/install.sh
@@ -21,8 +21,8 @@
#
# User may have a custom install script
-if [ -x ~/bin/installkernel ]; then exec ~/bin/installkernel "$@"; fi
-if [ -x /sbin/installkernel ]; then exec /sbin/installkernel "$@"; fi
+if [ -x ~/bin/${CROSS_COMPILE}installkernel ]; then exec ~/bin/${CROSS_COMPILE}installkernel "$@"; fi
+if [ -x /sbin/${CROSS_COMPILE}installkernel ]; then exec /sbin/${CROSS_COMPILE}installkernel "$@"; fi
if [ "$(basename $2)" = "zImage" ]; then
# Compressed install
diff --git a/arch/arm/common/amba.c b/arch/arm/common/amba.c
index a0507f8c33fe..c6beb751f2a9 100644
--- a/arch/arm/common/amba.c
+++ b/arch/arm/common/amba.c
@@ -169,7 +169,7 @@ static void amba_device_release(struct device *dev)
}
#define amba_attr(name,fmt,arg...) \
-static ssize_t show_##name(struct device *_dev, char *buf) \
+static ssize_t show_##name(struct device *_dev, struct device_attribute *attr, char *buf) \
{ \
struct amba_device *dev = to_amba_device(_dev); \
return sprintf(buf, fmt, arg); \
diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c
index 5797b1b100a1..cbf2165476b0 100644
--- a/arch/arm/common/dmabounce.c
+++ b/arch/arm/common/dmabounce.c
@@ -30,6 +30,8 @@
#include
#include
+#include
+
#undef DEBUG
#undef STATS
@@ -91,15 +93,12 @@ static void print_alloc_stats(struct dmabounce_device_info *device_info)
static inline struct dmabounce_device_info *
find_dmabounce_dev(struct device *dev)
{
- struct list_head *entry;
-
- list_for_each(entry, &dmabounce_devs) {
- struct dmabounce_device_info *d =
- list_entry(entry, struct dmabounce_device_info, node);
+ struct dmabounce_device_info *d;
+ list_for_each_entry(d, &dmabounce_devs, node)
if (d->dev == dev)
return d;
- }
+
return NULL;
}
@@ -170,15 +169,11 @@ alloc_safe_buffer(struct dmabounce_device_info *device_info, void *ptr,
static inline struct safe_buffer *
find_safe_buffer(struct dmabounce_device_info *device_info, dma_addr_t safe_dma_addr)
{
- struct list_head *entry;
-
- list_for_each(entry, &device_info->safe_buffers) {
- struct safe_buffer *b =
- list_entry(entry, struct safe_buffer, node);
+ struct safe_buffer *b;
+ list_for_each_entry(b, &device_info->safe_buffers, node)
if (b->safe_dma_addr == safe_dma_addr)
return b;
- }
return NULL;
}
@@ -299,15 +294,26 @@ unmap_single(struct device *dev, dma_addr_t dma_addr, size_t size,
__func__, buf->ptr, (void *) virt_to_dma(dev, buf->ptr),
buf->safe, (void *) buf->safe_dma_addr);
-
DO_STATS ( device_info->bounce_count++ );
- if ((dir == DMA_FROM_DEVICE) ||
- (dir == DMA_BIDIRECTIONAL)) {
+ if (dir == DMA_FROM_DEVICE || dir == DMA_BIDIRECTIONAL) {
+ unsigned long ptr;
+
dev_dbg(dev,
"%s: copy back safe %p to unsafe %p size %d\n",
__func__, buf->safe, buf->ptr, size);
memcpy(buf->ptr, buf->safe, size);
+
+ /*
+ * DMA buffers must have the same cache properties
+ * as if they were really used for DMA - which means
+ * data must be written back to RAM. Note that
+ * we don't use dmac_flush_range() here for the
+ * bidirectional case because we know the cache
+ * lines will be coherent with the data written.
+ */
+ ptr = (unsigned long)buf->ptr;
+ dmac_clean_range(ptr, ptr + size);
}
free_safe_buffer(device_info, buf);
}
diff --git a/arch/arm/common/sa1111.c b/arch/arm/common/sa1111.c
index 21fce3414ed1..38c2eb667eb9 100644
--- a/arch/arm/common/sa1111.c
+++ b/arch/arm/common/sa1111.c
@@ -721,16 +721,17 @@ __sa1111_probe(struct device *me, struct resource *mem, int irq)
return ret;
}
+static int sa1111_remove_one(struct device *dev, void *data)
+{
+ device_unregister(dev);
+ return 0;
+}
+
static void __sa1111_remove(struct sa1111 *sachip)
{
- struct list_head *l, *n;
void __iomem *irqbase = sachip->base + SA1111_INTC;
- list_for_each_safe(l, n, &sachip->dev->children) {
- struct device *d = list_to_dev(l);
-
- device_unregister(d);
- }
+ device_for_each_child(sachip->dev, NULL, sa1111_remove_one);
/* disable all IRQs */
sa1111_writel(0, irqbase + SA1111_INTEN0);
diff --git a/arch/arm/common/sharpsl_param.c b/arch/arm/common/sharpsl_param.c
index c2c557a224c2..c94864c5b1af 100644
--- a/arch/arm/common/sharpsl_param.c
+++ b/arch/arm/common/sharpsl_param.c
@@ -22,7 +22,7 @@
* them early in the boot process, then pass them to the appropriate drivers.
* Not all devices use all paramaters but the format is common to all.
*/
-#ifdef ARCH_SA1100
+#ifdef CONFIG_ARCH_SA1100
#define PARAM_BASE 0xe8ffc000
#else
#define PARAM_BASE 0xa0000a00
diff --git a/arch/arm/configs/enp2611_defconfig b/arch/arm/configs/enp2611_defconfig
index e8f9fccffe84..b8c51ee7f1bb 100644
--- a/arch/arm/configs/enp2611_defconfig
+++ b/arch/arm/configs/enp2611_defconfig
@@ -1,14 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Sun Mar 27 22:08:24 2005
+# Linux kernel version: 2.6.12-git6
+# Sat Jun 25 00:57:29 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
@@ -16,6 +15,7 @@ CONFIG_GENERIC_IOMAP=y
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
@@ -35,6 +35,8 @@ CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
@@ -50,7 +52,13 @@ CONFIG_BASE_SMALL=0
#
# Loadable module support
#
-# CONFIG_MODULES is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
#
# System Type
@@ -76,6 +84,7 @@ CONFIG_ARCH_IXP2000=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
#
@@ -90,6 +99,7 @@ CONFIG_ARCH_ENP2611=y
# CONFIG_ARCH_IXDP2800 is not set
# CONFIG_ARCH_IXDP2401 is not set
# CONFIG_ARCH_IXDP2801 is not set
+# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
#
# Processor Type
@@ -100,7 +110,6 @@ CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_MINICACHE=y
#
# Processor Features
@@ -112,9 +121,11 @@ CONFIG_XSCALE_PMU=y
#
# Bus support
#
+CONFIG_ISA_DMA_API=y
CONFIG_PCI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
@@ -124,7 +135,15 @@ CONFIG_PCI_NAMES=y
#
# Kernel Features
#
+# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_ALIGNMENT_TRAP=y
#
@@ -263,7 +282,6 @@ CONFIG_MTD_IXP2000=y
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
@@ -302,6 +320,7 @@ CONFIG_IOSCHED_CFQ=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -323,10 +342,11 @@ CONFIG_NET=y
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
-# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
@@ -343,6 +363,17 @@ CONFIG_SYN_COOKIES=y
# CONFIG_INET_TUNNEL is not set
# CONFIG_IP_TCPDIAG is not set
# CONFIG_IP_TCPDIAG_IPV6 is not set
+
+#
+# TCP congestion control
+#
+CONFIG_TCP_CONG_BIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_VEGAS is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
@@ -398,6 +429,7 @@ CONFIG_MII=y
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
#
# Tulip family network device support
@@ -434,9 +466,11 @@ CONFIG_EEPRO100=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
+# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
@@ -458,6 +492,7 @@ CONFIG_EEPRO100=y
# Wan interfaces
#
CONFIG_WAN=y
+# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_SYNCLINK_SYNCPPP is not set
CONFIG_HDLC=y
@@ -520,7 +555,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
#
# Character devices
@@ -541,6 +575,7 @@ CONFIG_SERIAL_8250_NR_UARTS=2
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
@@ -607,17 +642,18 @@ CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_IXP2000 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
@@ -631,7 +667,9 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
@@ -647,6 +685,7 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
@@ -656,14 +695,19 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
#
# Other I2C Chip support
#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -717,6 +761,7 @@ CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
@@ -757,7 +802,6 @@ CONFIG_DNOTIFY=y
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
@@ -795,12 +839,14 @@ CONFIG_JFFS2_RTIME=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
@@ -885,3 +931,4 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
+# CONFIG_TEXTSEARCH is not set
diff --git a/arch/arm/configs/ixdp2400_defconfig b/arch/arm/configs/ixdp2400_defconfig
index 4fd663ecbe39..3cfbe2ec29ca 100644
--- a/arch/arm/configs/ixdp2400_defconfig
+++ b/arch/arm/configs/ixdp2400_defconfig
@@ -1,14 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Sun Mar 27 21:13:38 2005
+# Linux kernel version: 2.6.12-git6
+# Sat Jun 25 00:58:38 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
@@ -16,6 +15,7 @@ CONFIG_GENERIC_IOMAP=y
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
@@ -35,6 +35,8 @@ CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
@@ -50,7 +52,13 @@ CONFIG_BASE_SMALL=0
#
# Loadable module support
#
-# CONFIG_MODULES is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
#
# System Type
@@ -76,6 +84,7 @@ CONFIG_ARCH_IXP2000=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
#
@@ -91,6 +100,7 @@ CONFIG_ARCH_IXDP2400=y
CONFIG_ARCH_IXDP2X00=y
# CONFIG_ARCH_IXDP2401 is not set
# CONFIG_ARCH_IXDP2801 is not set
+# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
#
# Processor Type
@@ -101,7 +111,6 @@ CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_MINICACHE=y
#
# Processor Features
@@ -113,9 +122,11 @@ CONFIG_XSCALE_PMU=y
#
# Bus support
#
+CONFIG_ISA_DMA_API=y
CONFIG_PCI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
@@ -125,7 +136,15 @@ CONFIG_PCI_NAMES=y
#
# Kernel Features
#
+# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_ALIGNMENT_TRAP=y
#
@@ -264,7 +283,6 @@ CONFIG_MTD_IXP2000=y
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
@@ -303,6 +321,7 @@ CONFIG_IOSCHED_CFQ=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -324,10 +343,11 @@ CONFIG_NET=y
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
-# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
@@ -344,6 +364,17 @@ CONFIG_SYN_COOKIES=y
# CONFIG_INET_TUNNEL is not set
# CONFIG_IP_TCPDIAG is not set
# CONFIG_IP_TCPDIAG_IPV6 is not set
+
+#
+# TCP congestion control
+#
+CONFIG_TCP_CONG_BIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_VEGAS is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
@@ -399,6 +430,7 @@ CONFIG_MII=y
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
#
# Tulip family network device support
@@ -435,9 +467,11 @@ CONFIG_EEPRO100=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
+# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
@@ -459,6 +493,7 @@ CONFIG_EEPRO100=y
# Wan interfaces
#
CONFIG_WAN=y
+# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_SYNCLINK_SYNCPPP is not set
CONFIG_HDLC=y
@@ -521,7 +556,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
#
# Character devices
@@ -542,6 +576,7 @@ CONFIG_SERIAL_8250_NR_UARTS=2
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
@@ -608,17 +643,18 @@ CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_IXP2000 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
@@ -632,7 +668,9 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
@@ -648,6 +686,7 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
@@ -657,14 +696,19 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
#
# Other I2C Chip support
#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -718,6 +762,7 @@ CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
@@ -758,7 +803,6 @@ CONFIG_DNOTIFY=y
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
@@ -796,12 +840,14 @@ CONFIG_JFFS2_RTIME=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
@@ -886,3 +932,4 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
+# CONFIG_TEXTSEARCH is not set
diff --git a/arch/arm/configs/ixdp2401_defconfig b/arch/arm/configs/ixdp2401_defconfig
index 6f51c98084a3..5c87e8e6969b 100644
--- a/arch/arm/configs/ixdp2401_defconfig
+++ b/arch/arm/configs/ixdp2401_defconfig
@@ -1,14 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Sun Mar 27 21:53:55 2005
+# Linux kernel version: 2.6.12-git6
+# Sat Jun 25 00:59:35 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
@@ -16,6 +15,7 @@ CONFIG_GENERIC_IOMAP=y
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
@@ -35,6 +35,8 @@ CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
@@ -50,7 +52,13 @@ CONFIG_BASE_SMALL=0
#
# Loadable module support
#
-# CONFIG_MODULES is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
#
# System Type
@@ -76,6 +84,7 @@ CONFIG_ARCH_IXP2000=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
#
@@ -91,6 +100,7 @@ CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
CONFIG_ARCH_IXDP2401=y
# CONFIG_ARCH_IXDP2801 is not set
CONFIG_ARCH_IXDP2X01=y
+# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
#
# Processor Type
@@ -101,7 +111,6 @@ CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_MINICACHE=y
#
# Processor Features
@@ -113,9 +122,11 @@ CONFIG_XSCALE_PMU=y
#
# Bus support
#
+CONFIG_ISA_DMA_API=y
CONFIG_PCI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
@@ -125,7 +136,15 @@ CONFIG_PCI_NAMES=y
#
# Kernel Features
#
+# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_ALIGNMENT_TRAP=y
#
@@ -264,7 +283,6 @@ CONFIG_MTD_IXP2000=y
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
@@ -303,6 +321,7 @@ CONFIG_IOSCHED_CFQ=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -324,10 +343,11 @@ CONFIG_NET=y
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
-# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
@@ -344,6 +364,17 @@ CONFIG_SYN_COOKIES=y
# CONFIG_INET_TUNNEL is not set
CONFIG_IP_TCPDIAG=y
# CONFIG_IP_TCPDIAG_IPV6 is not set
+
+#
+# TCP congestion control
+#
+CONFIG_TCP_CONG_BIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_VEGAS is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
@@ -399,6 +430,7 @@ CONFIG_MII=y
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
#
# Tulip family network device support
@@ -436,9 +468,11 @@ CONFIG_EEPRO100=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
+# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
@@ -460,6 +494,7 @@ CONFIG_EEPRO100=y
# Wan interfaces
#
CONFIG_WAN=y
+# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_SYNCLINK_SYNCPPP is not set
CONFIG_HDLC=y
@@ -522,7 +557,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
#
# Character devices
@@ -543,6 +577,7 @@ CONFIG_SERIAL_8250_NR_UARTS=2
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
@@ -609,17 +644,18 @@ CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_IXP2000 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
@@ -633,7 +669,9 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
@@ -649,6 +687,7 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
@@ -658,14 +697,19 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
#
# Other I2C Chip support
#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -719,6 +763,7 @@ CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
@@ -759,7 +804,6 @@ CONFIG_DNOTIFY=y
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
@@ -797,12 +841,14 @@ CONFIG_JFFS2_RTIME=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
@@ -887,3 +933,4 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
+# CONFIG_TEXTSEARCH is not set
diff --git a/arch/arm/configs/ixdp2800_defconfig b/arch/arm/configs/ixdp2800_defconfig
index 7be3521f91fc..3cb561a551cb 100644
--- a/arch/arm/configs/ixdp2800_defconfig
+++ b/arch/arm/configs/ixdp2800_defconfig
@@ -1,14 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Sun Mar 27 22:15:23 2005
+# Linux kernel version: 2.6.12-git6
+# Sat Jun 25 01:00:27 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
@@ -16,6 +15,7 @@ CONFIG_GENERIC_IOMAP=y
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
@@ -35,6 +35,8 @@ CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
@@ -50,7 +52,13 @@ CONFIG_BASE_SMALL=0
#
# Loadable module support
#
-# CONFIG_MODULES is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
#
# System Type
@@ -76,6 +84,7 @@ CONFIG_ARCH_IXP2000=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
#
@@ -91,6 +100,7 @@ CONFIG_ARCH_IXDP2800=y
CONFIG_ARCH_IXDP2X00=y
# CONFIG_ARCH_IXDP2401 is not set
# CONFIG_ARCH_IXDP2801 is not set
+# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
#
# Processor Type
@@ -101,7 +111,6 @@ CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_MINICACHE=y
#
# Processor Features
@@ -113,9 +122,11 @@ CONFIG_XSCALE_PMU=y
#
# Bus support
#
+CONFIG_ISA_DMA_API=y
CONFIG_PCI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
@@ -125,7 +136,15 @@ CONFIG_PCI_NAMES=y
#
# Kernel Features
#
+# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_ALIGNMENT_TRAP=y
#
@@ -264,7 +283,6 @@ CONFIG_MTD_IXP2000=y
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
@@ -303,6 +321,7 @@ CONFIG_IOSCHED_CFQ=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -324,10 +343,11 @@ CONFIG_NET=y
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
-# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
@@ -344,6 +364,17 @@ CONFIG_SYN_COOKIES=y
# CONFIG_INET_TUNNEL is not set
# CONFIG_IP_TCPDIAG is not set
# CONFIG_IP_TCPDIAG_IPV6 is not set
+
+#
+# TCP congestion control
+#
+CONFIG_TCP_CONG_BIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_VEGAS is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
@@ -399,6 +430,7 @@ CONFIG_MII=y
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
#
# Tulip family network device support
@@ -435,9 +467,11 @@ CONFIG_EEPRO100=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
+# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
@@ -459,6 +493,7 @@ CONFIG_EEPRO100=y
# Wan interfaces
#
CONFIG_WAN=y
+# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_SYNCLINK_SYNCPPP is not set
CONFIG_HDLC=y
@@ -521,7 +556,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
#
# Character devices
@@ -542,6 +576,7 @@ CONFIG_SERIAL_8250_NR_UARTS=2
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
@@ -608,17 +643,18 @@ CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_IXP2000 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
@@ -632,7 +668,9 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
@@ -648,6 +686,7 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
@@ -657,14 +696,19 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
#
# Other I2C Chip support
#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -718,6 +762,7 @@ CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
@@ -758,7 +803,6 @@ CONFIG_DNOTIFY=y
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
@@ -796,12 +840,14 @@ CONFIG_JFFS2_RTIME=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
@@ -886,3 +932,4 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
+# CONFIG_TEXTSEARCH is not set
diff --git a/arch/arm/configs/ixdp2801_defconfig b/arch/arm/configs/ixdp2801_defconfig
index cd84a20f30f1..b1e162f29cb9 100644
--- a/arch/arm/configs/ixdp2801_defconfig
+++ b/arch/arm/configs/ixdp2801_defconfig
@@ -1,14 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Sun Mar 27 22:39:19 2005
+# Linux kernel version: 2.6.12-git6
+# Sat Jun 25 01:01:18 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
@@ -16,6 +15,7 @@ CONFIG_GENERIC_IOMAP=y
CONFIG_EXPERIMENTAL=y
CONFIG_CLEAN_COMPILE=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
@@ -35,6 +35,8 @@ CONFIG_EMBEDDED=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
@@ -50,7 +52,13 @@ CONFIG_BASE_SMALL=0
#
# Loadable module support
#
-# CONFIG_MODULES is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_MODULE_FORCE_UNLOAD is not set
+CONFIG_OBSOLETE_MODPARM=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_KMOD=y
#
# System Type
@@ -76,6 +84,7 @@ CONFIG_ARCH_IXP2000=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
#
@@ -91,6 +100,7 @@ CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
# CONFIG_ARCH_IXDP2401 is not set
CONFIG_ARCH_IXDP2801=y
CONFIG_ARCH_IXDP2X01=y
+# CONFIG_IXP2000_SUPPORT_BROKEN_PCI_IO is not set
#
# Processor Type
@@ -101,7 +111,6 @@ CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_MINICACHE=y
#
# Processor Features
@@ -113,9 +122,11 @@ CONFIG_XSCALE_PMU=y
#
# Bus support
#
+CONFIG_ISA_DMA_API=y
CONFIG_PCI=y
CONFIG_PCI_LEGACY_PROC=y
CONFIG_PCI_NAMES=y
+# CONFIG_PCI_DEBUG is not set
#
# PCCARD (PCMCIA/CardBus) support
@@ -125,7 +136,15 @@ CONFIG_PCI_NAMES=y
#
# Kernel Features
#
+# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
+# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
CONFIG_ALIGNMENT_TRAP=y
#
@@ -264,7 +283,6 @@ CONFIG_MTD_IXP2000=y
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
@@ -303,6 +321,7 @@ CONFIG_IOSCHED_CFQ=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -324,10 +343,11 @@ CONFIG_NET=y
#
CONFIG_PACKET=y
CONFIG_PACKET_MMAP=y
-# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
@@ -344,6 +364,17 @@ CONFIG_SYN_COOKIES=y
# CONFIG_INET_TUNNEL is not set
# CONFIG_IP_TCPDIAG is not set
# CONFIG_IP_TCPDIAG_IPV6 is not set
+
+#
+# TCP congestion control
+#
+CONFIG_TCP_CONG_BIC=y
+CONFIG_TCP_CONG_WESTWOOD=m
+CONFIG_TCP_CONG_HTCP=m
+# CONFIG_TCP_CONG_HSTCP is not set
+# CONFIG_TCP_CONG_HYBLA is not set
+# CONFIG_TCP_CONG_VEGAS is not set
+# CONFIG_TCP_CONG_SCALABLE is not set
# CONFIG_IPV6 is not set
# CONFIG_NETFILTER is not set
@@ -399,6 +430,7 @@ CONFIG_MII=y
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_SMC91X is not set
+# CONFIG_DM9000 is not set
#
# Tulip family network device support
@@ -436,9 +468,11 @@ CONFIG_EEPRO100=y
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_R8169 is not set
+# CONFIG_SKGE is not set
# CONFIG_SK98LIN is not set
# CONFIG_VIA_VELOCITY is not set
# CONFIG_TIGON3 is not set
+# CONFIG_BNX2 is not set
#
# Ethernet (10000 Mbit)
@@ -460,6 +494,7 @@ CONFIG_EEPRO100=y
# Wan interfaces
#
CONFIG_WAN=y
+# CONFIG_DSCC4 is not set
# CONFIG_LANMEDIA is not set
# CONFIG_SYNCLINK_SYNCPPP is not set
CONFIG_HDLC=y
@@ -522,7 +557,6 @@ CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
#
# CONFIG_SERIO is not set
# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
#
# Character devices
@@ -543,6 +577,7 @@ CONFIG_SERIAL_8250_NR_UARTS=2
#
CONFIG_SERIAL_CORE=y
CONFIG_SERIAL_CORE_CONSOLE=y
+# CONFIG_SERIAL_JSM is not set
CONFIG_UNIX98_PTYS=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
@@ -609,17 +644,18 @@ CONFIG_I2C_ALGOBIT=y
# CONFIG_I2C_AMD8111 is not set
# CONFIG_I2C_I801 is not set
# CONFIG_I2C_I810 is not set
+# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_ISA is not set
# CONFIG_I2C_IXP2000 is not set
# CONFIG_I2C_NFORCE2 is not set
# CONFIG_I2C_PARPORT_LIGHT is not set
-# CONFIG_I2C_PIIX4 is not set
# CONFIG_I2C_PROSAVAGE is not set
# CONFIG_I2C_SAVAGE4 is not set
# CONFIG_SCx200_ACB is not set
# CONFIG_I2C_SIS5595 is not set
# CONFIG_I2C_SIS630 is not set
# CONFIG_I2C_SIS96X is not set
+# CONFIG_I2C_STUB is not set
# CONFIG_I2C_VIA is not set
# CONFIG_I2C_VIAPRO is not set
# CONFIG_I2C_VOODOO3 is not set
@@ -633,7 +669,9 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_ADM1025 is not set
# CONFIG_SENSORS_ADM1026 is not set
# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
# CONFIG_SENSORS_ASB100 is not set
+# CONFIG_SENSORS_ATXP1 is not set
# CONFIG_SENSORS_DS1621 is not set
# CONFIG_SENSORS_FSCHER is not set
# CONFIG_SENSORS_FSCPOS is not set
@@ -649,6 +687,7 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_LM85 is not set
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
@@ -658,14 +697,19 @@ CONFIG_I2C_SENSOR=y
# CONFIG_SENSORS_W83781D is not set
# CONFIG_SENSORS_W83L785TS is not set
# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
#
# Other I2C Chip support
#
+# CONFIG_SENSORS_DS1337 is not set
+# CONFIG_SENSORS_DS1374 is not set
CONFIG_SENSORS_EEPROM=y
# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_SENSORS_PCA9539 is not set
# CONFIG_SENSORS_PCF8591 is not set
# CONFIG_SENSORS_RTC8564 is not set
+# CONFIG_SENSORS_MAX6875 is not set
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
@@ -719,6 +763,7 @@ CONFIG_EXT2_FS=y
CONFIG_EXT2_FS_XATTR=y
CONFIG_EXT2_FS_POSIX_ACL=y
# CONFIG_EXT2_FS_SECURITY is not set
+# CONFIG_EXT2_FS_XIP is not set
CONFIG_EXT3_FS=y
CONFIG_EXT3_FS_XATTR=y
CONFIG_EXT3_FS_POSIX_ACL=y
@@ -759,7 +804,6 @@ CONFIG_DNOTIFY=y
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
CONFIG_TMPFS=y
# CONFIG_TMPFS_XATTR is not set
@@ -797,12 +841,14 @@ CONFIG_JFFS2_RTIME=y
#
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
+# CONFIG_NFS_V3_ACL is not set
# CONFIG_NFS_V4 is not set
# CONFIG_NFS_DIRECTIO is not set
# CONFIG_NFSD is not set
CONFIG_ROOT_NFS=y
CONFIG_LOCKD=y
CONFIG_LOCKD_V4=y
+CONFIG_NFS_COMMON=y
CONFIG_SUNRPC=y
# CONFIG_RPCSEC_GSS_KRB5 is not set
# CONFIG_RPCSEC_GSS_SPKM3 is not set
@@ -887,3 +933,4 @@ CONFIG_CRC32=y
# CONFIG_LIBCRC32C is not set
CONFIG_ZLIB_INFLATE=y
CONFIG_ZLIB_DEFLATE=y
+# CONFIG_TEXTSEARCH is not set
diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig
index 2a63fb277196..98b72ff38832 100644
--- a/arch/arm/configs/s3c2410_defconfig
+++ b/arch/arm/configs/s3c2410_defconfig
@@ -1,14 +1,13 @@
#
# Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Sun Mar 27 17:47:45 2005
+# Linux kernel version: 2.6.12-git4
+# Wed Jun 22 15:56:42 2005
#
CONFIG_ARM=y
CONFIG_MMU=y
CONFIG_UID16=y
CONFIG_RWSEM_GENERIC_SPINLOCK=y
CONFIG_GENERIC_CALIBRATE_DELAY=y
-CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
@@ -17,6 +16,7 @@ CONFIG_EXPERIMENTAL=y
# CONFIG_CLEAN_COMPILE is not set
CONFIG_BROKEN=y
CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
#
# General setup
@@ -35,6 +35,8 @@ CONFIG_KOBJECT_UEVENT=y
CONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
CONFIG_BASE_FULL=y
CONFIG_FUTEX=y
CONFIG_EPOLL=y
@@ -81,6 +83,7 @@ CONFIG_ARCH_S3C2410=y
# CONFIG_ARCH_VERSATILE is not set
# CONFIG_ARCH_IMX is not set
# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_AAEC2000 is not set
#
# S3C24XX Implementations
@@ -134,6 +137,7 @@ CONFIG_CPU_TLB_V4WBI=y
#
# Bus support
#
+CONFIG_ISA_DMA_API=y
#
# PCCARD (PCMCIA/CardBus) support
@@ -143,7 +147,9 @@ CONFIG_CPU_TLB_V4WBI=y
#
# Kernel Features
#
+# CONFIG_SMP is not set
# CONFIG_PREEMPT is not set
+# CONFIG_DISCONTIGMEM is not set
CONFIG_ALIGNMENT_TRAP=y
#
@@ -297,7 +303,6 @@ CONFIG_PARPORT_1284=y
#
# Block devices
#
-# CONFIG_BLK_DEV_FD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_COW_COMMON is not set
CONFIG_BLK_DEV_LOOP=y
@@ -359,6 +364,7 @@ CONFIG_BLK_DEV_IDE_BAST=y
#
# Fusion MPT device support
#
+# CONFIG_FUSION is not set
#
# IEEE 1394 (FireWire) support
@@ -378,10 +384,11 @@ CONFIG_NET=y
# Networking options
#
# CONFIG_PACKET is not set
-# CONFIG_NETLINK_DEV is not set
CONFIG_UNIX=y
# CONFIG_NET_KEY is not set
CONFIG_INET=y
+CONFIG_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
# CONFIG_IP_MULTICAST is not set
# CONFIG_IP_ADVANCED_ROUTER is not set
CONFIG_IP_PNP=y
@@ -443,8 +450,9 @@ CONFIG_NETDEVICES=y
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
-# CONFIG_MII is not set
+CONFIG_MII=m
# CONFIG_SMC91X is not set
+CONFIG_DM9000=m
#
# Ethernet (1000 Mbit)
@@ -521,7 +529,6 @@ CONFIG_SERIO_SERPORT=y
CONFIG_SERIO_LIBPS2=y
# CONFIG_SERIO_RAW is not set
# CONFIG_GAMEPORT is not set
-CONFIG_SOUND_GAMEPORT=y
#
# Character devices
@@ -605,7 +612,6 @@ CONFIG_S3C2410_RTC=y
#
# TPM devices
#
-# CONFIG_TCG_TPM is not set
#
# I2C support
@@ -654,6 +660,7 @@ CONFIG_SENSORS_LM78=m
CONFIG_SENSORS_LM85=m
# CONFIG_SENSORS_LM87 is not set
# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
# CONFIG_SENSORS_MAX1619 is not set
# CONFIG_SENSORS_PC87360 is not set
# CONFIG_SENSORS_SMSC47B397 is not set
@@ -665,6 +672,7 @@ CONFIG_SENSORS_LM85=m
#
# Other I2C Chip support
#
+# CONFIG_SENSORS_DS1337 is not set
CONFIG_SENSORS_EEPROM=m
# CONFIG_SENSORS_PCF8574 is not set
# CONFIG_SENSORS_PCF8591 is not set
@@ -696,8 +704,10 @@ CONFIG_FB=y
# CONFIG_FB_CFB_COPYAREA is not set
# CONFIG_FB_CFB_IMAGEBLIT is not set
# CONFIG_FB_SOFT_CURSOR is not set
+# CONFIG_FB_MACMODES is not set
CONFIG_FB_MODE_HELPERS=y
# CONFIG_FB_TILEBLITTING is not set
+# CONFIG_FB_S1D13XXX is not set
# CONFIG_FB_VIRTUAL is not set
#
@@ -782,7 +792,6 @@ CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
#
CONFIG_PROC_FS=y
CONFIG_SYSFS=y
-# CONFIG_DEVFS_FS is not set
# CONFIG_DEVPTS_FS_XATTR is not set
# CONFIG_TMPFS is not set
# CONFIG_HUGETLBFS is not set
diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile
index 4a2af55e134b..3e1b0327e4d7 100644
--- a/arch/arm/kernel/Makefile
+++ b/arch/arm/kernel/Makefile
@@ -6,7 +6,7 @@ AFLAGS_head.o := -DTEXTADDR=$(TEXTADDR) -DDATAADDR=$(DATAADDR)
# Object file lists.
-obj-y := arch.o compat.o dma.o entry-armv.o entry-common.o irq.o \
+obj-y := compat.o dma.o entry-armv.o entry-common.o irq.o \
process.o ptrace.o semaphore.o setup.o signal.o sys_arm.o \
time.o traps.o
diff --git a/arch/arm/kernel/arch.c b/arch/arm/kernel/arch.c
deleted file mode 100644
index 4e02fbeb10a6..000000000000
--- a/arch/arm/kernel/arch.c
+++ /dev/null
@@ -1,46 +0,0 @@
-/*
- * linux/arch/arm/kernel/arch.c
- *
- * Architecture specific fixups.
- */
-#include
-#include
-#include
-
-#include
-#include
-#include
-#include
-
-unsigned int vram_size;
-
-#ifdef CONFIG_ARCH_ACORN
-
-unsigned int memc_ctrl_reg;
-unsigned int number_mfm_drives;
-
-static int __init parse_tag_acorn(const struct tag *tag)
-{
- memc_ctrl_reg = tag->u.acorn.memc_control_reg;
- number_mfm_drives = tag->u.acorn.adfsdrives;
-
- switch (tag->u.acorn.vram_pages) {
- case 512:
- vram_size += PAGE_SIZE * 256;
- case 256:
- vram_size += PAGE_SIZE * 256;
- default:
- break;
- }
-#if 0
- if (vram_size) {
- desc->video_start = 0x02000000;
- desc->video_end = 0x02000000 + vram_size;
- }
-#endif
- return 0;
-}
-
-__tagtable(ATAG_ACORN, parse_tag_acorn);
-
-#endif
diff --git a/arch/arm/kernel/armksyms.c b/arch/arm/kernel/armksyms.c
index 4c38bd8bc298..b713c44c6fb4 100644
--- a/arch/arm/kernel/armksyms.c
+++ b/arch/arm/kernel/armksyms.c
@@ -30,9 +30,6 @@ extern void __lshrdi3(void);
extern void __modsi3(void);
extern void __muldi3(void);
extern void __ucmpdi2(void);
-extern void __udivdi3(void);
-extern void __umoddi3(void);
-extern void __udivmoddi4(void);
extern void __udivsi3(void);
extern void __umodsi3(void);
extern void __do_div64(void);
@@ -134,9 +131,6 @@ EXPORT_SYMBOL(__lshrdi3);
EXPORT_SYMBOL(__modsi3);
EXPORT_SYMBOL(__muldi3);
EXPORT_SYMBOL(__ucmpdi2);
-EXPORT_SYMBOL(__udivdi3);
-EXPORT_SYMBOL(__umoddi3);
-EXPORT_SYMBOL(__udivmoddi4);
EXPORT_SYMBOL(__udivsi3);
EXPORT_SYMBOL(__umodsi3);
EXPORT_SYMBOL(__do_div64);
diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c
index 3dc15b131f53..6540db691338 100644
--- a/arch/arm/kernel/ecard.c
+++ b/arch/arm/kernel/ecard.c
@@ -866,19 +866,19 @@ static struct expansion_card *__init ecard_alloc_card(int type, int slot)
return ec;
}
-static ssize_t ecard_show_irq(struct device *dev, char *buf)
+static ssize_t ecard_show_irq(struct device *dev, struct device_attribute *attr, char *buf)
{
struct expansion_card *ec = ECARD_DEV(dev);
return sprintf(buf, "%u\n", ec->irq);
}
-static ssize_t ecard_show_dma(struct device *dev, char *buf)
+static ssize_t ecard_show_dma(struct device *dev, struct device_attribute *attr, char *buf)
{
struct expansion_card *ec = ECARD_DEV(dev);
return sprintf(buf, "%u\n", ec->dma);
}
-static ssize_t ecard_show_resources(struct device *dev, char *buf)
+static ssize_t ecard_show_resources(struct device *dev, struct device_attribute *attr, char *buf)
{
struct expansion_card *ec = ECARD_DEV(dev);
char *str = buf;
@@ -893,19 +893,19 @@ static ssize_t ecard_show_resources(struct device *dev, char *buf)
return str - buf;
}
-static ssize_t ecard_show_vendor(struct device *dev, char *buf)
+static ssize_t ecard_show_vendor(struct device *dev, struct device_attribute *attr, char *buf)
{
struct expansion_card *ec = ECARD_DEV(dev);
return sprintf(buf, "%u\n", ec->cid.manufacturer);
}
-static ssize_t ecard_show_device(struct device *dev, char *buf)
+static ssize_t ecard_show_device(struct device *dev, struct device_attribute *attr, char *buf)
{
struct expansion_card *ec = ECARD_DEV(dev);
return sprintf(buf, "%u\n", ec->cid.product);
}
-static ssize_t ecard_show_type(struct device *dev, char *buf)
+static ssize_t ecard_show_type(struct device *dev, struct device_attribute *attr, char *buf)
{
struct expansion_card *ec = ECARD_DEV(dev);
return sprintf(buf, "%s\n", ec->type == ECARD_EASI ? "EASI" : "IOC");
diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index ff187f4308f0..395137a8fad2 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -4,6 +4,10 @@
* Copyright (C) 1992 Linus Torvalds
* Modifications for ARM processor Copyright (C) 1995-2000 Russell King.
*
+ * Support for Dynamic Tick Timer Copyright (C) 2004-2005 Nokia Corporation.
+ * Dynamic Tick Timer written by Tony Lindgren and
+ * Tuukka Tikkanen .
+ *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
@@ -37,6 +41,7 @@
#include
#include
#include
+#include
/*
* Maximum IRQ count. Currently, this is arbitary. However, it should
@@ -329,6 +334,15 @@ __do_irq(unsigned int irq, struct irqaction *action, struct pt_regs *regs)
spin_unlock(&irq_controller_lock);
+#ifdef CONFIG_NO_IDLE_HZ
+ if (!(action->flags & SA_TIMER) && system_timer->dyn_tick != NULL) {
+ write_seqlock(&xtime_lock);
+ if (system_timer->dyn_tick->state & DYN_TICK_ENABLED)
+ system_timer->dyn_tick->handler(irq, 0, regs);
+ write_sequnlock(&xtime_lock);
+ }
+#endif
+
if (!(action->flags & SA_INTERRUPT))
local_irq_enable();
diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c
index 8f146a4b4752..bbea636ff687 100644
--- a/arch/arm/kernel/process.c
+++ b/arch/arm/kernel/process.c
@@ -32,6 +32,7 @@
#include
#include
#include
+#include
extern const char *processor_modes[];
extern void setup_mm_for_reboot(char mode);
@@ -85,8 +86,10 @@ EXPORT_SYMBOL(pm_power_off);
void default_idle(void)
{
local_irq_disable();
- if (!need_resched() && !hlt_counter)
+ if (!need_resched() && !hlt_counter) {
+ timer_dyn_reprogram();
arch_idle();
+ }
local_irq_enable();
}
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index 9fed5fa194d9..35b7273cfdb4 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -359,7 +359,8 @@ void cpu_init(void)
"I" (offsetof(struct stack, abt[0])),
"I" (PSR_F_BIT | PSR_I_BIT | UND_MODE),
"I" (offsetof(struct stack, und[0])),
- "I" (PSR_F_BIT | PSR_I_BIT | SVC_MODE));
+ "I" (PSR_F_BIT | PSR_I_BIT | SVC_MODE)
+ : "r14");
}
static struct machine_desc * __init setup_machine(unsigned int nr)
@@ -395,6 +396,20 @@ static void __init early_initrd(char **p)
}
__early_param("initrd=", early_initrd);
+static void __init add_memory(unsigned long start, unsigned long size)
+{
+ /*
+ * Ensure that start/size are aligned to a page boundary.
+ * Size is appropriately rounded down, start is rounded up.
+ */
+ size -= start & ~PAGE_MASK;
+
+ meminfo.bank[meminfo.nr_banks].start = PAGE_ALIGN(start);
+ meminfo.bank[meminfo.nr_banks].size = size & PAGE_MASK;
+ meminfo.bank[meminfo.nr_banks].node = PHYS_TO_NID(start);
+ meminfo.nr_banks += 1;
+}
+
/*
* Pick out the memory size. We look for mem=size@start,
* where start and size are "size[KkMm]"
@@ -419,10 +434,7 @@ static void __init early_mem(char **p)
if (**p == '@')
start = memparse(*p + 1, p);
- meminfo.bank[meminfo.nr_banks].start = start;
- meminfo.bank[meminfo.nr_banks].size = size;
- meminfo.bank[meminfo.nr_banks].node = PHYS_TO_NID(start);
- meminfo.nr_banks += 1;
+ add_memory(start, size);
}
__early_param("mem=", early_mem);
@@ -564,11 +576,7 @@ static int __init parse_tag_mem32(const struct tag *tag)
tag->u.mem.start, tag->u.mem.size / 1024);
return -EINVAL;
}
- meminfo.bank[meminfo.nr_banks].start = tag->u.mem.start;
- meminfo.bank[meminfo.nr_banks].size = tag->u.mem.size;
- meminfo.bank[meminfo.nr_banks].node = PHYS_TO_NID(tag->u.mem.start);
- meminfo.nr_banks += 1;
-
+ add_memory(tag->u.mem.start, tag->u.mem.size);
return 0;
}
diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c
index 931919fd5121..5e435e42dacd 100644
--- a/arch/arm/kernel/signal.c
+++ b/arch/arm/kernel/signal.c
@@ -19,6 +19,7 @@
#include
#include "ptrace.h"
+#include "signal.h"
#define _BLOCKABLE (~(sigmask(SIGKILL) | sigmask(SIGSTOP)))
@@ -35,7 +36,7 @@
#define SWI_THUMB_SIGRETURN (0xdf00 << 16 | 0x2700 | (__NR_sigreturn - __NR_SYSCALL_BASE))
#define SWI_THUMB_RT_SIGRETURN (0xdf00 << 16 | 0x2700 | (__NR_rt_sigreturn - __NR_SYSCALL_BASE))
-static const unsigned long retcodes[4] = {
+const unsigned long sigreturn_codes[4] = {
SWI_SYS_SIGRETURN, SWI_THUMB_SIGRETURN,
SWI_SYS_RT_SIGRETURN, SWI_THUMB_RT_SIGRETURN
};
@@ -500,17 +501,25 @@ setup_return(struct pt_regs *regs, struct k_sigaction *ka,
if (ka->sa.sa_flags & SA_SIGINFO)
idx += 2;
- if (__put_user(retcodes[idx], rc))
+ if (__put_user(sigreturn_codes[idx], rc))
return 1;
- /*
- * Ensure that the instruction cache sees
- * the return code written onto the stack.
- */
- flush_icache_range((unsigned long)rc,
- (unsigned long)(rc + 1));
+ if (cpsr & MODE32_BIT) {
+ /*
+ * 32-bit code can use the new high-page
+ * signal return code support.
+ */
+ retcode = KERN_SIGRETURN_CODE + (idx << 2) + thumb;
+ } else {
+ /*
+ * Ensure that the instruction cache sees
+ * the return code written onto the stack.
+ */
+ flush_icache_range((unsigned long)rc,
+ (unsigned long)(rc + 1));
- retcode = ((unsigned long)rc) + thumb;
+ retcode = ((unsigned long)rc) + thumb;
+ }
}
regs->ARM_r0 = usig;
@@ -688,7 +697,7 @@ static int do_signal(sigset_t *oldset, struct pt_regs *regs, int syscall)
if (!user_mode(regs))
return 0;
- if (try_to_freeze(0))
+ if (try_to_freeze())
goto no_signal;
if (current->ptrace & PT_SINGLESTEP)
diff --git a/arch/arm/kernel/signal.h b/arch/arm/kernel/signal.h
new file mode 100644
index 000000000000..91d26faca62b
--- /dev/null
+++ b/arch/arm/kernel/signal.h
@@ -0,0 +1,12 @@
+/*
+ * linux/arch/arm/kernel/signal.h
+ *
+ * Copyright (C) 2005 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#define KERN_SIGRETURN_CODE 0xffff0500
+
+extern const unsigned long sigreturn_codes[4];
diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c
index 45ed036336e0..a931409c8fe4 100644
--- a/arch/arm/kernel/smp.c
+++ b/arch/arm/kernel/smp.c
@@ -145,7 +145,8 @@ int __init __cpu_up(unsigned int cpu)
pgd_free(pgd);
if (ret) {
- printk(KERN_CRIT "cpu_up: processor %d failed to boot\n", cpu);
+ printk(KERN_CRIT "CPU%u: processor failed to boot\n", cpu);
+
/*
* FIXME: We need to clean up the new idle thread. --rmk
*/
@@ -501,3 +502,126 @@ int __init setup_profiling_timer(unsigned int multiplier)
{
return -EINVAL;
}
+
+static int
+on_each_cpu_mask(void (*func)(void *), void *info, int retry, int wait,
+ cpumask_t mask)
+{
+ int ret = 0;
+
+ preempt_disable();
+
+ ret = smp_call_function_on_cpu(func, info, retry, wait, mask);
+ if (cpu_isset(smp_processor_id(), mask))
+ func(info);
+
+ preempt_enable();
+
+ return ret;
+}
+
+/**********************************************************************/
+
+/*
+ * TLB operations
+ */
+struct tlb_args {
+ struct vm_area_struct *ta_vma;
+ unsigned long ta_start;
+ unsigned long ta_end;
+};
+
+static inline void ipi_flush_tlb_all(void *ignored)
+{
+ local_flush_tlb_all();
+}
+
+static inline void ipi_flush_tlb_mm(void *arg)
+{
+ struct mm_struct *mm = (struct mm_struct *)arg;
+
+ local_flush_tlb_mm(mm);
+}
+
+static inline void ipi_flush_tlb_page(void *arg)
+{
+ struct tlb_args *ta = (struct tlb_args *)arg;
+
+ local_flush_tlb_page(ta->ta_vma, ta->ta_start);
+}
+
+static inline void ipi_flush_tlb_kernel_page(void *arg)
+{
+ struct tlb_args *ta = (struct tlb_args *)arg;
+
+ local_flush_tlb_kernel_page(ta->ta_start);
+}
+
+static inline void ipi_flush_tlb_range(void *arg)
+{
+ struct tlb_args *ta = (struct tlb_args *)arg;
+
+ local_flush_tlb_range(ta->ta_vma, ta->ta_start, ta->ta_end);
+}
+
+static inline void ipi_flush_tlb_kernel_range(void *arg)
+{
+ struct tlb_args *ta = (struct tlb_args *)arg;
+
+ local_flush_tlb_kernel_range(ta->ta_start, ta->ta_end);
+}
+
+void flush_tlb_all(void)
+{
+ on_each_cpu(ipi_flush_tlb_all, NULL, 1, 1);
+}
+
+void flush_tlb_mm(struct mm_struct *mm)
+{
+ cpumask_t mask = mm->cpu_vm_mask;
+
+ on_each_cpu_mask(ipi_flush_tlb_mm, mm, 1, 1, mask);
+}
+
+void flush_tlb_page(struct vm_area_struct *vma, unsigned long uaddr)
+{
+ cpumask_t mask = vma->vm_mm->cpu_vm_mask;
+ struct tlb_args ta;
+
+ ta.ta_vma = vma;
+ ta.ta_start = uaddr;
+
+ on_each_cpu_mask(ipi_flush_tlb_page, &ta, 1, 1, mask);
+}
+
+void flush_tlb_kernel_page(unsigned long kaddr)
+{
+ struct tlb_args ta;
+
+ ta.ta_start = kaddr;
+
+ on_each_cpu(ipi_flush_tlb_kernel_page, &ta, 1, 1);
+}
+
+void flush_tlb_range(struct vm_area_struct *vma,
+ unsigned long start, unsigned long end)
+{
+ cpumask_t mask = vma->vm_mm->cpu_vm_mask;
+ struct tlb_args ta;
+
+ ta.ta_vma = vma;
+ ta.ta_start = start;
+ ta.ta_end = end;
+
+ on_each_cpu_mask(ipi_flush_tlb_range, &ta, 1, 1, mask);
+}
+
+void flush_tlb_kernel_range(unsigned long start, unsigned long end)
+{
+ struct tlb_args ta;
+
+ ta.ta_start = start;
+ ta.ta_end = end;
+
+ on_each_cpu(ipi_flush_tlb_kernel_range, &ta, 1, 1);
+}
diff --git a/arch/arm/kernel/time.c b/arch/arm/kernel/time.c
index c232f24f4a60..1b7fcd50c3e2 100644
--- a/arch/arm/kernel/time.c
+++ b/arch/arm/kernel/time.c
@@ -381,6 +381,99 @@ static struct sysdev_class timer_sysclass = {
.resume = timer_resume,
};
+#ifdef CONFIG_NO_IDLE_HZ
+static int timer_dyn_tick_enable(void)
+{
+ struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick;
+ unsigned long flags;
+ int ret = -ENODEV;
+
+ if (dyn_tick) {
+ write_seqlock_irqsave(&xtime_lock, flags);
+ ret = 0;
+ if (!(dyn_tick->state & DYN_TICK_ENABLED)) {
+ ret = dyn_tick->enable();
+
+ if (ret == 0)
+ dyn_tick->state |= DYN_TICK_ENABLED;
+ }
+ write_sequnlock_irqrestore(&xtime_lock, flags);
+ }
+
+ return ret;
+}
+
+static int timer_dyn_tick_disable(void)
+{
+ struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick;
+ unsigned long flags;
+ int ret = -ENODEV;
+
+ if (dyn_tick) {
+ write_seqlock_irqsave(&xtime_lock, flags);
+ ret = 0;
+ if (dyn_tick->state & DYN_TICK_ENABLED) {
+ ret = dyn_tick->disable();
+
+ if (ret == 0)
+ dyn_tick->state &= ~DYN_TICK_ENABLED;
+ }
+ write_sequnlock_irqrestore(&xtime_lock, flags);
+ }
+
+ return ret;
+}
+
+/*
+ * Reprogram the system timer for at least the calculated time interval.
+ * This function should be called from the idle thread with IRQs disabled,
+ * immediately before sleeping.
+ */
+void timer_dyn_reprogram(void)
+{
+ struct dyn_tick_timer *dyn_tick = system_timer->dyn_tick;
+
+ write_seqlock(&xtime_lock);
+ if (dyn_tick->state & DYN_TICK_ENABLED)
+ dyn_tick->reprogram(next_timer_interrupt() - jiffies);
+ write_sequnlock(&xtime_lock);
+}
+
+static ssize_t timer_show_dyn_tick(struct sys_device *dev, char *buf)
+{
+ return sprintf(buf, "%i\n",
+ (system_timer->dyn_tick->state & DYN_TICK_ENABLED) >> 1);
+}
+
+static ssize_t timer_set_dyn_tick(struct sys_device *dev, const char *buf,
+ size_t count)
+{
+ unsigned int enable = simple_strtoul(buf, NULL, 2);
+
+ if (enable)
+ timer_dyn_tick_enable();
+ else
+ timer_dyn_tick_disable();
+
+ return count;
+}
+static SYSDEV_ATTR(dyn_tick, 0644, timer_show_dyn_tick, timer_set_dyn_tick);
+
+/*
+ * dyntick=enable|disable
+ */
+static char dyntick_str[4] __initdata = "";
+
+static int __init dyntick_setup(char *str)
+{
+ if (str)
+ strlcpy(dyntick_str, str, sizeof(dyntick_str));
+ return 1;
+}
+
+__setup("dyntick=", dyntick_setup);
+#endif
+
static int __init timer_init_sysfs(void)
{
int ret = sysdev_class_register(&timer_sysclass);
@@ -388,6 +481,20 @@ static int __init timer_init_sysfs(void)
system_timer->dev.cls = &timer_sysclass;
ret = sysdev_register(&system_timer->dev);
}
+
+#ifdef CONFIG_NO_IDLE_HZ
+ if (ret == 0 && system_timer->dyn_tick) {
+ ret = sysdev_create_file(&system_timer->dev, &attr_dyn_tick);
+
+ /*
+ * Turn on dynamic tick after calibrate delay
+ * for correct bogomips
+ */
+ if (ret == 0 && dyntick_str[0] == 'e')
+ ret = timer_dyn_tick_enable();
+ }
+#endif
+
return ret;
}
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index 45d2a032d890..df2cb06ce424 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -30,6 +30,7 @@
#include
#include "ptrace.h"
+#include "signal.h"
const char *processor_modes[]=
{ "USER_26", "FIQ_26" , "IRQ_26" , "SVC_26" , "UK4_26" , "UK5_26" , "UK6_26" , "UK7_26" ,
@@ -229,16 +230,8 @@ NORET_TYPE void die(const char *str, struct pt_regs *regs, int err)
do_exit(SIGSEGV);
}
-void die_if_kernel(const char *str, struct pt_regs *regs, int err)
-{
- if (user_mode(regs))
- return;
-
- die(str, regs, err);
-}
-
-static void notify_die(const char *str, struct pt_regs *regs, siginfo_t *info,
- unsigned long err, unsigned long trap)
+void notify_die(const char *str, struct pt_regs *regs, struct siginfo *info,
+ unsigned long err, unsigned long trap)
{
if (user_mode(regs)) {
current->thread.error_code = err;
@@ -683,6 +676,14 @@ void __init trap_init(void)
memcpy((void *)0xffff0000, __vectors_start, __vectors_end - __vectors_start);
memcpy((void *)0xffff0200, __stubs_start, __stubs_end - __stubs_start);
memcpy((void *)0xffff1000 - kuser_sz, __kuser_helper_start, kuser_sz);
+
+ /*
+ * Copy signal return handlers into the vector page, and
+ * set sigreturn to be a pointer to these.
+ */
+ memcpy((void *)KERN_SIGRETURN_CODE, sigreturn_codes,
+ sizeof(sigreturn_codes));
+
flush_icache_range(0xffff0000, 0xffff0000 + PAGE_SIZE);
modify_domain(DOMAIN_USER, DOMAIN_CLIENT);
}
diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile
index c0e65833ffc4..8725d63e4219 100644
--- a/arch/arm/lib/Makefile
+++ b/arch/arm/lib/Makefile
@@ -11,7 +11,7 @@ lib-y := backtrace.o changebit.o csumipv6.o csumpartial.o \
strnlen_user.o strchr.o strrchr.o testchangebit.o \
testclearbit.o testsetbit.o uaccess.o getuser.o \
putuser.o ashldi3.o ashrdi3.o lshrdi3.o muldi3.o \
- ucmpdi2.o udivdi3.o lib1funcs.o div64.o \
+ ucmpdi2.o lib1funcs.o div64.o \
io-readsb.o io-writesb.o io-readsl.o io-writesl.o
ifeq ($(CONFIG_CPU_32v3),y)
diff --git a/arch/arm/lib/ashldi3.c b/arch/arm/lib/ashldi3.c
index 130f5a839669..b62875cfd8f8 100644
--- a/arch/arm/lib/ashldi3.c
+++ b/arch/arm/lib/ashldi3.c
@@ -31,31 +31,26 @@ Boston, MA 02111-1307, USA. */
#include "gcclib.h"
-DItype
-__ashldi3 (DItype u, word_type b)
+s64 __ashldi3(s64 u, int b)
{
- DIunion w;
- word_type bm;
- DIunion uu;
+ DIunion w;
+ int bm;
+ DIunion uu;
- if (b == 0)
- return u;
+ if (b == 0)
+ return u;
- uu.ll = u;
+ uu.ll = u;
- bm = (sizeof (SItype) * BITS_PER_UNIT) - b;
- if (bm <= 0)
- {
- w.s.low = 0;
- w.s.high = (USItype)uu.s.low << -bm;
- }
- else
- {
- USItype carries = (USItype)uu.s.low >> bm;
- w.s.low = (USItype)uu.s.low << b;
- w.s.high = ((USItype)uu.s.high << b) | carries;
- }
+ bm = (sizeof(s32) * BITS_PER_UNIT) - b;
+ if (bm <= 0) {
+ w.s.low = 0;
+ w.s.high = (u32) uu.s.low << -bm;
+ } else {
+ u32 carries = (u32) uu.s.low >> bm;
+ w.s.low = (u32) uu.s.low << b;
+ w.s.high = ((u32) uu.s.high << b) | carries;
+ }
- return w.ll;
+ return w.ll;
}
-
diff --git a/arch/arm/lib/ashrdi3.c b/arch/arm/lib/ashrdi3.c
index 71625d218f8d..9a8600a7543f 100644
--- a/arch/arm/lib/ashrdi3.c
+++ b/arch/arm/lib/ashrdi3.c
@@ -31,31 +31,27 @@ Boston, MA 02111-1307, USA. */
#include "gcclib.h"
-DItype
-__ashrdi3 (DItype u, word_type b)
+s64 __ashrdi3(s64 u, int b)
{
- DIunion w;
- word_type bm;
- DIunion uu;
+ DIunion w;
+ int bm;
+ DIunion uu;
- if (b == 0)
- return u;
+ if (b == 0)
+ return u;
- uu.ll = u;
+ uu.ll = u;
- bm = (sizeof (SItype) * BITS_PER_UNIT) - b;
- if (bm <= 0)
- {
- /* w.s.high = 1..1 or 0..0 */
- w.s.high = uu.s.high >> (sizeof (SItype) * BITS_PER_UNIT - 1);
- w.s.low = uu.s.high >> -bm;
- }
- else
- {
- USItype carries = (USItype)uu.s.high << bm;
- w.s.high = uu.s.high >> b;
- w.s.low = ((USItype)uu.s.low >> b) | carries;
- }
+ bm = (sizeof(s32) * BITS_PER_UNIT) - b;
+ if (bm <= 0) {
+ /* w.s.high = 1..1 or 0..0 */
+ w.s.high = uu.s.high >> (sizeof(s32) * BITS_PER_UNIT - 1);
+ w.s.low = uu.s.high >> -bm;
+ } else {
+ u32 carries = (u32) uu.s.high << bm;
+ w.s.high = uu.s.high >> b;
+ w.s.low = ((u32) uu.s.low >> b) | carries;
+ }
- return w.ll;
+ return w.ll;
}
diff --git a/arch/arm/lib/gcclib.h b/arch/arm/lib/gcclib.h
index 65314a3d9e27..8b6dcc656de7 100644
--- a/arch/arm/lib/gcclib.h
+++ b/arch/arm/lib/gcclib.h
@@ -1,25 +1,22 @@
/* gcclib.h -- definitions for various functions 'borrowed' from gcc-2.95.3 */
/* I Molton 29/07/01 */
-#define BITS_PER_UNIT 8
-#define SI_TYPE_SIZE (sizeof (SItype) * BITS_PER_UNIT)
+#include
-typedef unsigned int UQItype __attribute__ ((mode (QI)));
-typedef int SItype __attribute__ ((mode (SI)));
-typedef unsigned int USItype __attribute__ ((mode (SI)));
-typedef int DItype __attribute__ ((mode (DI)));
-typedef int word_type __attribute__ ((mode (__word__)));
-typedef unsigned int UDItype __attribute__ ((mode (DI)));
+#define BITS_PER_UNIT 8
+#define SI_TYPE_SIZE (sizeof(s32) * BITS_PER_UNIT)
#ifdef __ARMEB__
- struct DIstruct {SItype high, low;};
+struct DIstruct {
+ s32 high, low;
+};
#else
- struct DIstruct {SItype low, high;};
+struct DIstruct {
+ s32 low, high;
+};
#endif
-typedef union
-{
- struct DIstruct s;
- DItype ll;
+typedef union {
+ struct DIstruct s;
+ s64 ll;
} DIunion;
-
diff --git a/arch/arm/lib/longlong.h b/arch/arm/lib/longlong.h
deleted file mode 100644
index 179eea4edc35..000000000000
--- a/arch/arm/lib/longlong.h
+++ /dev/null
@@ -1,183 +0,0 @@
-/* longlong.h -- based on code from gcc-2.95.3
-
- definitions for mixed size 32/64 bit arithmetic.
- Copyright (C) 1991, 92, 94, 95, 96, 1997, 1998 Free Software Foundation, Inc.
-
- This definition file is free software; you can redistribute it
- and/or modify it under the terms of the GNU General Public
- License as published by the Free Software Foundation; either
- version 2, or (at your option) any later version.
-
- This definition file is distributed in the hope that it will be
- useful, but WITHOUT ANY WARRANTY; without even the implied
- warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
- See the GNU General Public License for more details.
-
- You should have received a copy of the GNU General Public License
- along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place - Suite 330,
- Boston, MA 02111-1307, USA. */
-
-/* Borrowed from GCC 2.95.3, I Molton 29/07/01 */
-
-#ifndef SI_TYPE_SIZE
-#define SI_TYPE_SIZE 32
-#endif
-
-#define __BITS4 (SI_TYPE_SIZE / 4)
-#define __ll_B (1L << (SI_TYPE_SIZE / 2))
-#define __ll_lowpart(t) ((USItype) (t) % __ll_B)
-#define __ll_highpart(t) ((USItype) (t) / __ll_B)
-
-/* Define auxiliary asm macros.
-
- 1) umul_ppmm(high_prod, low_prod, multipler, multiplicand)
- multiplies two USItype integers MULTIPLER and MULTIPLICAND,
- and generates a two-part USItype product in HIGH_PROD and
- LOW_PROD.
-
- 2) __umulsidi3(a,b) multiplies two USItype integers A and B,
- and returns a UDItype product. This is just a variant of umul_ppmm.
-
- 3) udiv_qrnnd(quotient, remainder, high_numerator, low_numerator,
- denominator) divides a two-word unsigned integer, composed by the
- integers HIGH_NUMERATOR and LOW_NUMERATOR, by DENOMINATOR and
- places the quotient in QUOTIENT and the remainder in REMAINDER.
- HIGH_NUMERATOR must be less than DENOMINATOR for correct operation.
- If, in addition, the most significant bit of DENOMINATOR must be 1,
- then the pre-processor symbol UDIV_NEEDS_NORMALIZATION is defined to 1.
-
- 4) sdiv_qrnnd(quotient, remainder, high_numerator, low_numerator,
- denominator). Like udiv_qrnnd but the numbers are signed. The
- quotient is rounded towards 0.
-
- 5) count_leading_zeros(count, x) counts the number of zero-bits from
- the msb to the first non-zero bit. This is the number of steps X
- needs to be shifted left to set the msb. Undefined for X == 0.
-
- 6) add_ssaaaa(high_sum, low_sum, high_addend_1, low_addend_1,
- high_addend_2, low_addend_2) adds two two-word unsigned integers,
- composed by HIGH_ADDEND_1 and LOW_ADDEND_1, and HIGH_ADDEND_2 and
- LOW_ADDEND_2 respectively. The result is placed in HIGH_SUM and
- LOW_SUM. Overflow (i.e. carry out) is not stored anywhere, and is
- lost.
-
- 7) sub_ddmmss(high_difference, low_difference, high_minuend,
- low_minuend, high_subtrahend, low_subtrahend) subtracts two
- two-word unsigned integers, composed by HIGH_MINUEND_1 and
- LOW_MINUEND_1, and HIGH_SUBTRAHEND_2 and LOW_SUBTRAHEND_2
- respectively. The result is placed in HIGH_DIFFERENCE and
- LOW_DIFFERENCE. Overflow (i.e. carry out) is not stored anywhere,
- and is lost.
-
- If any of these macros are left undefined for a particular CPU,
- C macros are used. */
-
-#if defined (__arm__)
-#define add_ssaaaa(sh, sl, ah, al, bh, bl) \
- __asm__ ("adds %1, %4, %5 \n\
- adc %0, %2, %3" \
- : "=r" ((USItype) (sh)), \
- "=&r" ((USItype) (sl)) \
- : "%r" ((USItype) (ah)), \
- "rI" ((USItype) (bh)), \
- "%r" ((USItype) (al)), \
- "rI" ((USItype) (bl)))
-#define sub_ddmmss(sh, sl, ah, al, bh, bl) \
- __asm__ ("subs %1, %4, %5 \n\
- sbc %0, %2, %3" \
- : "=r" ((USItype) (sh)), \
- "=&r" ((USItype) (sl)) \
- : "r" ((USItype) (ah)), \
- "rI" ((USItype) (bh)), \
- "r" ((USItype) (al)), \
- "rI" ((USItype) (bl)))
-#define umul_ppmm(xh, xl, a, b) \
-{register USItype __t0, __t1, __t2; \
- __asm__ ("%@ Inlined umul_ppmm \n\
- mov %2, %5, lsr #16 \n\
- mov %0, %6, lsr #16 \n\
- bic %3, %5, %2, lsl #16 \n\
- bic %4, %6, %0, lsl #16 \n\
- mul %1, %3, %4 \n\
- mul %4, %2, %4 \n\
- mul %3, %0, %3 \n\
- mul %0, %2, %0 \n\
- adds %3, %4, %3 \n\
- addcs %0, %0, #65536 \n\
- adds %1, %1, %3, lsl #16 \n\
- adc %0, %0, %3, lsr #16" \
- : "=&r" ((USItype) (xh)), \
- "=r" ((USItype) (xl)), \
- "=&r" (__t0), "=&r" (__t1), "=r" (__t2) \
- : "r" ((USItype) (a)), \
- "r" ((USItype) (b)));}
-#define UMUL_TIME 20
-#define UDIV_TIME 100
-#endif /* __arm__ */
-
-#define __umulsidi3(u, v) \
- ({DIunion __w; \
- umul_ppmm (__w.s.high, __w.s.low, u, v); \
- __w.ll; })
-
-#define __udiv_qrnnd_c(q, r, n1, n0, d) \
- do { \
- USItype __d1, __d0, __q1, __q0; \
- USItype __r1, __r0, __m; \
- __d1 = __ll_highpart (d); \
- __d0 = __ll_lowpart (d); \
- \
- __r1 = (n1) % __d1; \
- __q1 = (n1) / __d1; \
- __m = (USItype) __q1 * __d0; \
- __r1 = __r1 * __ll_B | __ll_highpart (n0); \
- if (__r1 < __m) \
- { \
- __q1--, __r1 += (d); \
- if (__r1 >= (d)) /* i.e. we didn't get carry when adding to __r1 */\
- if (__r1 < __m) \
- __q1--, __r1 += (d); \
- } \
- __r1 -= __m; \
- \
- __r0 = __r1 % __d1; \
- __q0 = __r1 / __d1; \
- __m = (USItype) __q0 * __d0; \
- __r0 = __r0 * __ll_B | __ll_lowpart (n0); \
- if (__r0 < __m) \
- { \
- __q0--, __r0 += (d); \
- if (__r0 >= (d)) \
- if (__r0 < __m) \
- __q0--, __r0 += (d); \
- } \
- __r0 -= __m; \
- \
- (q) = (USItype) __q1 * __ll_B | __q0; \
- (r) = __r0; \
- } while (0)
-
-#define UDIV_NEEDS_NORMALIZATION 1
-#define udiv_qrnnd __udiv_qrnnd_c
-
-#define count_leading_zeros(count, x) \
- do { \
- USItype __xr = (x); \
- USItype __a; \
- \
- if (SI_TYPE_SIZE <= 32) \
- { \
- __a = __xr < ((USItype)1<<2*__BITS4) \
- ? (__xr < ((USItype)1<<__BITS4) ? 0 : __BITS4) \
- : (__xr < ((USItype)1<<3*__BITS4) ? 2*__BITS4 : 3*__BITS4); \
- } \
- else \
- { \
- for (__a = SI_TYPE_SIZE - 8; __a > 0; __a -= 8) \
- if (((__xr >> __a) & 0xff) != 0) \
- break; \
- } \
- \
- (count) = SI_TYPE_SIZE - (__clz_tab[__xr >> __a] + __a); \
- } while (0)
diff --git a/arch/arm/lib/lshrdi3.c b/arch/arm/lib/lshrdi3.c
index b666f1bad451..3681f49d2b6e 100644
--- a/arch/arm/lib/lshrdi3.c
+++ b/arch/arm/lib/lshrdi3.c
@@ -31,31 +31,26 @@ Boston, MA 02111-1307, USA. */
#include "gcclib.h"
-DItype
-__lshrdi3 (DItype u, word_type b)
+s64 __lshrdi3(s64 u, int b)
{
- DIunion w;
- word_type bm;
- DIunion uu;
+ DIunion w;
+ int bm;
+ DIunion uu;
- if (b == 0)
- return u;
+ if (b == 0)
+ return u;
- uu.ll = u;
+ uu.ll = u;
- bm = (sizeof (SItype) * BITS_PER_UNIT) - b;
- if (bm <= 0)
- {
- w.s.high = 0;
- w.s.low = (USItype)uu.s.high >> -bm;
- }
- else
- {
- USItype carries = (USItype)uu.s.high << bm;
- w.s.high = (USItype)uu.s.high >> b;
- w.s.low = ((USItype)uu.s.low >> b) | carries;
- }
+ bm = (sizeof(s32) * BITS_PER_UNIT) - b;
+ if (bm <= 0) {
+ w.s.high = 0;
+ w.s.low = (u32) uu.s.high >> -bm;
+ } else {
+ u32 carries = (u32) uu.s.high << bm;
+ w.s.high = (u32) uu.s.high >> b;
+ w.s.low = ((u32) uu.s.low >> b) | carries;
+ }
- return w.ll;
+ return w.ll;
}
-
diff --git a/arch/arm/lib/muldi3.c b/arch/arm/lib/muldi3.c
index 44d611b1cfdb..0a3b93313f18 100644
--- a/arch/arm/lib/muldi3.c
+++ b/arch/arm/lib/muldi3.c
@@ -32,7 +32,7 @@ Boston, MA 02111-1307, USA. */
#include "gcclib.h"
#define umul_ppmm(xh, xl, a, b) \
-{register USItype __t0, __t1, __t2; \
+{register u32 __t0, __t1, __t2; \
__asm__ ("%@ Inlined umul_ppmm \n\
mov %2, %5, lsr #16 \n\
mov %0, %6, lsr #16 \n\
@@ -46,32 +46,27 @@ Boston, MA 02111-1307, USA. */
addcs %0, %0, #65536 \n\
adds %1, %1, %3, lsl #16 \n\
adc %0, %0, %3, lsr #16" \
- : "=&r" ((USItype) (xh)), \
- "=r" ((USItype) (xl)), \
+ : "=&r" ((u32) (xh)), \
+ "=r" ((u32) (xl)), \
"=&r" (__t0), "=&r" (__t1), "=r" (__t2) \
- : "r" ((USItype) (a)), \
- "r" ((USItype) (b)));}
-
+ : "r" ((u32) (a)), \
+ "r" ((u32) (b)));}
#define __umulsidi3(u, v) \
({DIunion __w; \
umul_ppmm (__w.s.high, __w.s.low, u, v); \
__w.ll; })
-
-DItype
-__muldi3 (DItype u, DItype v)
+s64 __muldi3(s64 u, s64 v)
{
- DIunion w;
- DIunion uu, vv;
+ DIunion w;
+ DIunion uu, vv;
- uu.ll = u,
- vv.ll = v;
+ uu.ll = u, vv.ll = v;
- w.ll = __umulsidi3 (uu.s.low, vv.s.low);
- w.s.high += ((USItype) uu.s.low * (USItype) vv.s.high
- + (USItype) uu.s.high * (USItype) vv.s.low);
+ w.ll = __umulsidi3(uu.s.low, vv.s.low);
+ w.s.high += ((u32) uu.s.low * (u32) vv.s.high
+ + (u32) uu.s.high * (u32) vv.s.low);
- return w.ll;
+ return w.ll;
}
-
diff --git a/arch/arm/lib/ucmpdi2.c b/arch/arm/lib/ucmpdi2.c
index 6c6ae63efa02..57f3f2df3850 100644
--- a/arch/arm/lib/ucmpdi2.c
+++ b/arch/arm/lib/ucmpdi2.c
@@ -31,21 +31,19 @@ Boston, MA 02111-1307, USA. */
#include "gcclib.h"
-word_type
-__ucmpdi2 (DItype a, DItype b)
+int __ucmpdi2(s64 a, s64 b)
{
- DIunion au, bu;
+ DIunion au, bu;
- au.ll = a, bu.ll = b;
+ au.ll = a, bu.ll = b;
- if ((USItype) au.s.high < (USItype) bu.s.high)
- return 0;
- else if ((USItype) au.s.high > (USItype) bu.s.high)
- return 2;
- if ((USItype) au.s.low < (USItype) bu.s.low)
- return 0;
- else if ((USItype) au.s.low > (USItype) bu.s.low)
- return 2;
- return 1;
+ if ((u32) au.s.high < (u32) bu.s.high)
+ return 0;
+ else if ((u32) au.s.high > (u32) bu.s.high)
+ return 2;
+ if ((u32) au.s.low < (u32) bu.s.low)
+ return 0;
+ else if ((u32) au.s.low > (u32) bu.s.low)
+ return 2;
+ return 1;
}
-
diff --git a/arch/arm/lib/udivdi3.c b/arch/arm/lib/udivdi3.c
deleted file mode 100644
index d25195f673f4..000000000000
--- a/arch/arm/lib/udivdi3.c
+++ /dev/null
@@ -1,242 +0,0 @@
-/* More subroutines needed by GCC output code on some machines. */
-/* Compile this one with gcc. */
-/* Copyright (C) 1989, 92-98, 1999 Free Software Foundation, Inc.
-
-This file is part of GNU CC.
-
-GNU CC is free software; you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation; either version 2, or (at your option)
-any later version.
-
-GNU CC is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with GNU CC; see the file COPYING. If not, write to
-the Free Software Foundation, 59 Temple Place - Suite 330,
-Boston, MA 02111-1307, USA. */
-
-/* As a special exception, if you link this library with other files,
- some of which are compiled with GCC, to produce an executable,
- this library does not by itself cause the resulting executable
- to be covered by the GNU General Public License.
- This exception does not however invalidate any other reasons why
- the executable file might be covered by the GNU General Public License.
- */
-/* support functions required by the kernel. based on code from gcc-2.95.3 */
-/* I Molton 29/07/01 */
-
-#include "gcclib.h"
-#include "longlong.h"
-
-static const UQItype __clz_tab[] =
-{
- 0,1,2,2,3,3,3,3,4,4,4,4,4,4,4,4,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,5,
- 6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,6,
- 7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,
- 7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,7,
- 8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,
- 8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,
- 8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,
- 8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,8,
-};
-
-UDItype
-__udivmoddi4 (UDItype n, UDItype d, UDItype *rp)
-{
- DIunion ww;
- DIunion nn, dd;
- DIunion rr;
- USItype d0, d1, n0, n1, n2;
- USItype q0, q1;
- USItype b, bm;
-
- nn.ll = n;
- dd.ll = d;
-
- d0 = dd.s.low;
- d1 = dd.s.high;
- n0 = nn.s.low;
- n1 = nn.s.high;
-
- if (d1 == 0)
- {
- if (d0 > n1)
- {
- /* 0q = nn / 0D */
-
- count_leading_zeros (bm, d0);
-
- if (bm != 0)
- {
- /* Normalize, i.e. make the most significant bit of the
- denominator set. */
-
- d0 = d0 << bm;
- n1 = (n1 << bm) | (n0 >> (SI_TYPE_SIZE - bm));
- n0 = n0 << bm;
- }
-
- udiv_qrnnd (q0, n0, n1, n0, d0);
- q1 = 0;
-
- /* Remainder in n0 >> bm. */
- }
- else
- {
- /* qq = NN / 0d */
-
- if (d0 == 0)
- d0 = 1 / d0; /* Divide intentionally by zero. */
-
- count_leading_zeros (bm, d0);
-
- if (bm == 0)
- {
- /* From (n1 >= d0) /\ (the most significant bit of d0 is set),
- conclude (the most significant bit of n1 is set) /\ (the
- leading quotient digit q1 = 1).
-
- This special case is necessary, not an optimization.
- (Shifts counts of SI_TYPE_SIZE are undefined.) */
-
- n1 -= d0;
- q1 = 1;
- }
- else
- {
- /* Normalize. */
-
- b = SI_TYPE_SIZE - bm;
-
- d0 = d0 << bm;
- n2 = n1 >> b;
- n1 = (n1 << bm) | (n0 >> b);
- n0 = n0 << bm;
-
- udiv_qrnnd (q1, n1, n2, n1, d0);
- }
-
- /* n1 != d0... */
-
- udiv_qrnnd (q0, n0, n1, n0, d0);
-
- /* Remainder in n0 >> bm. */
- }
-
- if (rp != 0)
- {
- rr.s.low = n0 >> bm;
- rr.s.high = 0;
- *rp = rr.ll;
- }
- }
- else
- {
- if (d1 > n1)
- {
- /* 00 = nn / DD */
-
- q0 = 0;
- q1 = 0;
-
- /* Remainder in n1n0. */
- if (rp != 0)
- {
- rr.s.low = n0;
- rr.s.high = n1;
- *rp = rr.ll;
- }
- }
- else
- {
- /* 0q = NN / dd */
-
- count_leading_zeros (bm, d1);
- if (bm == 0)
- {
- /* From (n1 >= d1) /\ (the most significant bit of d1 is set),
- conclude (the most significant bit of n1 is set) /\ (the
- quotient digit q0 = 0 or 1).
-
- This special case is necessary, not an optimization. */
-
- /* The condition on the next line takes advantage of that
- n1 >= d1 (true due to program flow). */
- if (n1 > d1 || n0 >= d0)
- {
- q0 = 1;
- sub_ddmmss (n1, n0, n1, n0, d1, d0);
- }
- else
- q0 = 0;
-
- q1 = 0;
-
- if (rp != 0)
- {
- rr.s.low = n0;
- rr.s.high = n1;
- *rp = rr.ll;
- }
- }
- else
- {
- USItype m1, m0;
- /* Normalize. */
-
- b = SI_TYPE_SIZE - bm;
-
- d1 = (d1 << bm) | (d0 >> b);
- d0 = d0 << bm;
- n2 = n1 >> b;
- n1 = (n1 << bm) | (n0 >> b);
- n0 = n0 << bm;
-
- udiv_qrnnd (q0, n1, n2, n1, d1);
- umul_ppmm (m1, m0, q0, d0);
-
- if (m1 > n1 || (m1 == n1 && m0 > n0))
- {
- q0--;
- sub_ddmmss (m1, m0, m1, m0, d1, d0);
- }
-
- q1 = 0;
-
- /* Remainder in (n1n0 - m1m0) >> bm. */
- if (rp != 0)
- {
- sub_ddmmss (n1, n0, n1, n0, m1, m0);
- rr.s.low = (n1 << b) | (n0 >> bm);
- rr.s.high = n1 >> bm;
- *rp = rr.ll;
- }
- }
- }
- }
-
- ww.s.low = q0;
- ww.s.high = q1;
- return ww.ll;
-}
-
-UDItype
-__udivdi3 (UDItype n, UDItype d)
-{
- return __udivmoddi4 (n, d, (UDItype *) 0);
-}
-
-UDItype
-__umoddi3 (UDItype u, UDItype v)
-{
- UDItype w;
-
- (void) __udivmoddi4 (u ,v, &w);
-
- return w;
-}
-
diff --git a/arch/arm/mach-aaec2000/Kconfig b/arch/arm/mach-aaec2000/Kconfig
new file mode 100644
index 000000000000..5e4bef93754c
--- /dev/null
+++ b/arch/arm/mach-aaec2000/Kconfig
@@ -0,0 +1,11 @@
+if ARCH_AAEC2000
+
+menu "Agilent AAEC-2000 Implementations"
+
+config MACH_AAED2000
+ bool "Agilent AAED-2000 Development Platform"
+ select CPU_ARM920T
+
+endmenu
+
+endif
diff --git a/arch/arm/mach-aaec2000/Makefile b/arch/arm/mach-aaec2000/Makefile
new file mode 100644
index 000000000000..20ec83896c37
--- /dev/null
+++ b/arch/arm/mach-aaec2000/Makefile
@@ -0,0 +1,9 @@
+#
+# Makefile for the linux kernel.
+#
+
+# Common support (must be linked before board specific support)
+obj-y += core.o
+
+# Specific board support
+obj-$(CONFIG_MACH_AAED2000) += aaed2000.o
diff --git a/arch/arm/mach-aaec2000/Makefile.boot b/arch/arm/mach-aaec2000/Makefile.boot
new file mode 100644
index 000000000000..8f5a8b7c53c7
--- /dev/null
+++ b/arch/arm/mach-aaec2000/Makefile.boot
@@ -0,0 +1 @@
+ zreladdr-y := 0xf0008000
diff --git a/arch/arm/mach-aaec2000/aaed2000.c b/arch/arm/mach-aaec2000/aaed2000.c
new file mode 100644
index 000000000000..5417ca3f4621
--- /dev/null
+++ b/arch/arm/mach-aaec2000/aaed2000.c
@@ -0,0 +1,48 @@
+/*
+ * linux/arch/arm/mach-aaec2000/aaed2000.c
+ *
+ * Support for the Agilent AAED-2000 Development Platform.
+ *
+ * Copyright (c) 2005 Nicolas Bellido Y Ortega
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+#include
+#include
+#include
+#include
+#include
+#include
+
+#include
+#include
+#include
+#include
+#include
+
+#include
+#include
+#include
+
+#include "core.h"
+
+static void __init aaed2000_init_irq(void)
+{
+ aaec2000_init_irq();
+}
+
+static void __init aaed2000_map_io(void)
+{
+ aaec2000_map_io();
+}
+
+MACHINE_START(AAED2000, "Agilent AAED-2000 Development Platform")
+ MAINTAINER("Nicolas Bellido Y Ortega")
+ BOOT_MEM(0xf0000000, PIO_BASE, VIO_BASE)
+ MAPIO(aaed2000_map_io)
+ INITIRQ(aaed2000_init_irq)
+ .timer = &aaec2000_timer,
+MACHINE_END
diff --git a/arch/arm/mach-aaec2000/core.c b/arch/arm/mach-aaec2000/core.c
new file mode 100644
index 000000000000..aece0cd4f0a3
--- /dev/null
+++ b/arch/arm/mach-aaec2000/core.c
@@ -0,0 +1,157 @@
+/*
+ * linux/arch/arm/mach-aaec2000/core.c
+ *
+ * Code common to all AAEC-2000 machines
+ *
+ * Copyright (c) 2005 Nicolas Bellido Y Ortega
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include
+#include
+#include
+#include
+#include
+#include
+#include
+#include
+#include
+
+#include
+#include
+
+#include
+#include
+#include
+
+/*
+ * Common I/O mapping:
+ *
+ * Static virtual address mappings are as follow:
+ *
+ * 0xf8000000-0xf8001ffff: Devices connected to APB bus
+ * 0xf8002000-0xf8003ffff: Devices connected to AHB bus
+ *
+ * Below 0xe8000000 is reserved for vm allocation.
+ *
+ * The machine specific code must provide the extra mapping beside the
+ * default mapping provided here.
+ */
+static struct map_desc standard_io_desc[] __initdata = {
+ /* virtual physical length type */
+ { VIO_APB_BASE, PIO_APB_BASE, IO_APB_LENGTH, MT_DEVICE },
+ { VIO_AHB_BASE, PIO_AHB_BASE, IO_AHB_LENGTH, MT_DEVICE }
+};
+
+void __init aaec2000_map_io(void)
+{
+ iotable_init(standard_io_desc, ARRAY_SIZE(standard_io_desc));
+}
+
+/*
+ * Interrupt handling routines
+ */
+static void aaec2000_int_ack(unsigned int irq)
+{
+ IRQ_INTSR = 1 << irq;
+}
+
+static void aaec2000_int_mask(unsigned int irq)
+{
+ IRQ_INTENC |= (1 << irq);
+}
+
+static void aaec2000_int_unmask(unsigned int irq)
+{
+ IRQ_INTENS |= (1 << irq);
+}
+
+static struct irqchip aaec2000_irq_chip = {
+ .ack = aaec2000_int_ack,
+ .mask = aaec2000_int_mask,
+ .unmask = aaec2000_int_unmask,
+};
+
+void __init aaec2000_init_irq(void)
+{
+ unsigned int i;
+
+ for (i = 0; i < NR_IRQS; i++) {
+ set_irq_handler(i, do_level_IRQ);
+ set_irq_chip(i, &aaec2000_irq_chip);
+ set_irq_flags(i, IRQF_VALID);
+ }
+
+ /* Disable all interrupts */
+ IRQ_INTENC = 0xffffffff;
+
+ /* Clear any pending interrupts */
+ IRQ_INTSR = IRQ_INTSR;
+}
+
+/*
+ * Time keeping
+ */
+/* IRQs are disabled before entering here from do_gettimeofday() */
+static unsigned long aaec2000_gettimeoffset(void)
+{
+ unsigned long ticks_to_match, elapsed, usec;
+
+ /* Get ticks before next timer match */
+ ticks_to_match = TIMER1_LOAD - TIMER1_VAL;
+
+ /* We need elapsed ticks since last match */
+ elapsed = LATCH - ticks_to_match;
+
+ /* Now, convert them to usec */
+ usec = (unsigned long)(elapsed * (tick_nsec / 1000))/LATCH;
+
+ return usec;
+}
+
+/* We enter here with IRQs enabled */
+static irqreturn_t
+aaec2000_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
+{
+ /* TODO: Check timer accuracy */
+ write_seqlock(&xtime_lock);
+
+ timer_tick(regs);
+ TIMER1_CLEAR = 1;
+
+ write_sequnlock(&xtime_lock);
+
+ return IRQ_HANDLED;
+}
+
+static struct irqaction aaec2000_timer_irq = {
+ .name = "AAEC-2000 Timer Tick",
+ .flags = SA_INTERRUPT | SA_TIMER,
+ .handler = aaec2000_timer_interrupt,
+};
+
+static void __init aaec2000_timer_init(void)
+{
+ /* Disable timer 1 */
+ TIMER1_CTRL = 0;
+
+ /* We have somehow to generate a 100Hz clock.
+ * We then use the 508KHz timer in periodic mode.
+ */
+ TIMER1_LOAD = LATCH;
+ TIMER1_CLEAR = 1; /* Clear interrupt */
+
+ setup_irq(INT_TMR1_OFL, &aaec2000_timer_irq);
+
+ TIMER1_CTRL = TIMER_CTRL_ENABLE |
+ TIMER_CTRL_PERIODIC |
+ TIMER_CTRL_CLKSEL_508K;
+}
+
+struct sys_timer aaec2000_timer = {
+ .init = aaec2000_timer_init,
+ .offset = aaec2000_gettimeoffset,
+};
+
diff --git a/arch/arm/mach-aaec2000/core.h b/arch/arm/mach-aaec2000/core.h
new file mode 100644
index 000000000000..91893d848c16
--- /dev/null
+++ b/arch/arm/mach-aaec2000/core.h
@@ -0,0 +1,16 @@
+/*
+ * linux/arch/arm/mach-aaec2000/core.h
+ *
+ * Copyright (c) 2005 Nicolas Bellido Y Ortega
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+struct sys_timer;
+
+extern struct sys_timer aaec2000_timer;
+extern void __init aaec2000_map_io(void);
+extern void __init aaec2000_init_irq(void);
diff --git a/arch/arm/mach-clps711x/Kconfig b/arch/arm/mach-clps711x/Kconfig
index 45c930ccd064..0793dcf54f2e 100644
--- a/arch/arm/mach-clps711x/Kconfig
+++ b/arch/arm/mach-clps711x/Kconfig
@@ -28,7 +28,7 @@ config ARCH_CLEP7312
config ARCH_EDB7211
bool "EDB7211"
select ISA
- select DISCONTIGMEM
+ select ARCH_DISCONTIGMEM_ENABLE
help
Say Y here if you intend to run this kernel on a Cirrus Logic EDB-7211
evaluation board.
diff --git a/arch/arm/mach-clps711x/time.c b/arch/arm/mach-clps711x/time.c
index 383d4e0c6e35..1a23f0dcd4b8 100644
--- a/arch/arm/mach-clps711x/time.c
+++ b/arch/arm/mach-clps711x/time.c
@@ -57,8 +57,8 @@ p720t_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs)
static struct irqaction clps711x_timer_irq = {
.name = "CLPS711x Timer Tick",
- .flags = SA_INTERRUPT,
- .handler = p720t_timer_interrupt
+ .flags = SA_INTERRUPT | SA_TIMER,
+ .handler = p720t_timer_interrupt,
};
static void __init clps711x_timer_init(void)
diff --git a/arch/arm/mach-clps7500/core.c b/arch/arm/mach-clps7500/core.c
index fdfededfd96f..90e85f434f6f 100644
--- a/arch/arm/mach-clps7500/core.c
+++ b/arch/arm/mach-clps7500/core.c
@@ -26,6 +26,8 @@
#include
#include