ALSA: mpu401: clean up interrupt specification

The semantics of snd_mpu401_uart_new()'s interrupt parameters are
somewhat counterintuitive:  To prevent the function from allocating its
own interrupt, either the irq number must be invalid, or the irq_flags
parameter must be zero.  At the same time, the irq parameter being
invalid specifies that the mpu401 code has to work without an interrupt
allocated by the caller.  This implies that, if there is an interrupt
and it is allocated by the caller, the irq parameter must be set to
a valid-looking number which then isn't actually used.

With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value,
which forces us to handle the parameters differently.

This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the
device interrupt is handled by the caller, and makes the allocation of
the interrupt to depend only on the irq parameter.  As suggested by
Takashi, the irq_flags parameter was dropped because, when used, it had
the constant value IRQF_DISABLED.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Documentation/DocBook/writing-an-alsa-driver.tmpl

@@ -4288,7 +4288,7 @@ struct _snd_pcm_runtime {
 <![CDATA[
   struct snd_rawmidi *rmidi;
   snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, port, info_flags,
-                      irq, irq_flags, &rmidi);
+                      irq, &rmidi);
 ]]>
           </programlisting>
         </informalexample>
@@ -4343,6 +4343,13 @@ struct _snd_pcm_runtime {
 	by itself to start processing the output stream in the irq handler.
 	</para>
 
+	<para>
+	If the MPU-401 interface shares its interrupt with the other logical
+	devices on the card, set <constant>MPU401_INFO_IRQ_HOOK</constant>
+	(see <link linkend="midi-interface-interrupt-handler"><citetitle>
+	below</citetitle></link>).
+	</para>
+
       <para>
         Usually, the port address corresponds to the command port and
         port + 1 corresponds to the data port. If not, you may change
@@ -4375,14 +4382,12 @@ struct _snd_pcm_runtime {
       </para>
 
       <para>
-        The 6th argument specifies the irq number for UART. If the irq
-      is already allocated, pass 0 to the 7th argument
-      (<parameter>irq_flags</parameter>). Otherwise, pass the flags
-      for irq allocation 
-      (<constant>SA_XXX</constant> bits) to it, and the irq will be
-      reserved by the mpu401-uart layer. If the card doesn't generate
-      UART interrupts, pass -1 as the irq number. Then a timer
-      interrupt will be invoked for polling. 
+	The 6th argument specifies the ISA irq number that will be
+	allocated.  If no interrupt is to be allocated (because your
+	code is already allocating a shared interrupt, or because the
+	device does not use interrupts), pass -1 instead.
+	For a MPU-401 device without an interrupt, a polling timer
+	will be used instead.
       </para>
     </section>
 
@@ -4390,12 +4395,13 @@ struct _snd_pcm_runtime {
       <title>Interrupt Handler</title>
       <para>
         When the interrupt is allocated in
-      <function>snd_mpu401_uart_new()</function>, the private
-      interrupt handler is used, hence you don't have anything else to do
-      than creating the mpu401 stuff. Otherwise, you have to call
-      <function>snd_mpu401_uart_interrupt()</function> explicitly when
-      a UART interrupt is invoked and checked in your own interrupt
-      handler.  
+      <function>snd_mpu401_uart_new()</function>, an exclusive ISA
+      interrupt handler is automatically used, hence you don't have
+      anything else to do than creating the mpu401 stuff.  Otherwise, you
+      have to set <constant>MPU401_INFO_IRQ_HOOK</constant>, and call
+      <function>snd_mpu401_uart_interrupt()</function> explicitly from your
+      own interrupt handler when it has determined that a UART interrupt
+      has occurred.
       </para>
 
       <para>

include/sound/mpu401.h

@@ -50,7 +50,10 @@
 #define MPU401_INFO_INTEGRATED	(1 << 2)	/* integrated h/w port */
 #define MPU401_INFO_MMIO	(1 << 3)	/* MMIO access */
 #define MPU401_INFO_TX_IRQ	(1 << 4)	/* independent TX irq */
+#define MPU401_INFO_IRQ_HOOK	(1 << 5)	/* mpu401 irq handler is called
+						   from driver irq handler */
 #define MPU401_INFO_NO_ACK	(1 << 6)	/* No ACK cmd needed */
+#define MPU401_INFO_USE_TIMER	(1 << 15)	/* internal */
 
 #define MPU401_MODE_BIT_INPUT		0
 #define MPU401_MODE_BIT_OUTPUT		1
@@ -73,8 +76,7 @@ struct snd_mpu401 {
 	unsigned long port;		/* base port of MPU-401 chip */
 	unsigned long cport;		/* port + 1 (usually) */
 	struct resource *res;		/* port resource */
-	int irq;			/* IRQ number of MPU-401 chip (-1 = poll) */
-	int irq_flags;
+	int irq;			/* IRQ number of MPU-401 chip */
 
 	unsigned long mode;		/* MPU401_MODE_XXXX */
 	int timer_invoked;
@@ -131,7 +133,6 @@ int snd_mpu401_uart_new(struct snd_card *card,
 			unsigned long port,
 			unsigned int info_flags,
 			int irq,
-			int irq_flags,
 			struct snd_rawmidi ** rrawmidi);
 
 #endif /* __SOUND_MPU401_H */

sound/drivers/mpu401/mpu401.c

@@ -86,8 +86,7 @@ static int snd_mpu401_create(int dev, struct snd_card **rcard)
 	}
 
 	err = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401, port[dev], 0,
-				  irq[dev], irq[dev] >= 0 ? IRQF_DISABLED : 0,
-				  NULL);
+				  irq[dev], NULL);
 	if (err < 0) {
 		printk(KERN_ERR "MPU401 not detected at 0x%lx\n", port[dev]);
 		goto _err;

sound/drivers/mpu401/mpu401_uart.c

@@ -3,7 +3,7 @@
  *  Routines for control of MPU-401 in UART mode
  *
  *  MPU-401 supports UART mode which is not capable generate transmit
- *  interrupts thus output is done via polling. Also, if irq < 0, then
+ *  interrupts thus output is done via polling. Without interrupt,
  *  input is done also via polling. Do not expect good performance.
  *
  *
@@ -374,7 +374,7 @@ snd_mpu401_uart_input_trigger(struct snd_rawmidi_substream *substream, int up)
 			/* first time - flush FIFO */
 			while (max-- > 0)
 				mpu->read(mpu, MPU401D(mpu));
-			if (mpu->irq < 0)
+			if (mpu->info_flags & MPU401_INFO_USE_TIMER)
 				snd_mpu401_uart_add_timer(mpu, 1);
 		}
 		
@@ -383,7 +383,7 @@ snd_mpu401_uart_input_trigger(struct snd_rawmidi_substream *substream, int up)
 		snd_mpu401_uart_input_read(mpu);
 		spin_unlock_irqrestore(&mpu->input_lock, flags);
 	} else {
-		if (mpu->irq < 0)
+		if (mpu->info_flags & MPU401_INFO_USE_TIMER)
 			snd_mpu401_uart_remove_timer(mpu, 1);
 		clear_bit(MPU401_MODE_BIT_INPUT_TRIGGER, &mpu->mode);
 	}
@@ -496,7 +496,7 @@ static struct snd_rawmidi_ops snd_mpu401_uart_input =
 static void snd_mpu401_uart_free(struct snd_rawmidi *rmidi)
 {
 	struct snd_mpu401 *mpu = rmidi->private_data;
-	if (mpu->irq_flags && mpu->irq >= 0)
+	if (mpu->irq >= 0)
 		free_irq(mpu->irq, (void *) mpu);
 	release_and_free_resource(mpu->res);
 	kfree(mpu);
@@ -509,8 +509,7 @@ static void snd_mpu401_uart_free(struct snd_rawmidi *rmidi)
  * @hardware: the hardware type, MPU401_HW_XXXX
  * @port: the base address of MPU401 port
  * @info_flags: bitflags MPU401_INFO_XXX
- * @irq: the irq number, -1 if no interrupt for mpu
- * @irq_flags: the irq request flags (SA_XXX), 0 if irq was already reserved.
+ * @irq: the ISA irq number, -1 if not to be allocated
  * @rrawmidi: the pointer to store the new rawmidi instance
  *
  * Creates a new MPU-401 instance.
@@ -525,7 +524,7 @@ int snd_mpu401_uart_new(struct snd_card *card, int device,
 			unsigned short hardware,
 			unsigned long port,
 			unsigned int info_flags,
-			int irq, int irq_flags,
+			int irq,
 			struct snd_rawmidi ** rrawmidi)
 {
 	struct snd_mpu401 *mpu;
@@ -577,8 +576,8 @@ int snd_mpu401_uart_new(struct snd_card *card, int device,
 		mpu->cport = port + 2;
 	else
 		mpu->cport = port + 1;
-	if (irq >= 0 && irq_flags) {
-		if (request_irq(irq, snd_mpu401_uart_interrupt, irq_flags,
+	if (irq >= 0) {
+		if (request_irq(irq, snd_mpu401_uart_interrupt, IRQF_DISABLED,
 				"MPU401 UART", (void *) mpu)) {
 			snd_printk(KERN_ERR "mpu401_uart: "
 				   "unable to grab IRQ %d\n", irq);
@@ -586,9 +585,10 @@ int snd_mpu401_uart_new(struct snd_card *card, int device,
 			return -EBUSY;
 		}
 	}
+	if (irq < 0 && !(info_flags & MPU401_INFO_IRQ_HOOK))
+		info_flags |= MPU401_INFO_USE_TIMER;
 	mpu->info_flags = info_flags;
 	mpu->irq = irq;
-	mpu->irq_flags = irq_flags;
 	if (card->shortname[0])
 		snprintf(rmidi->name, sizeof(rmidi->name), "%s MIDI",
 			 card->shortname);

sound/isa/ad1816a/ad1816a.c

@@ -204,7 +204,7 @@ static int __devinit snd_card_ad1816a_probe(int dev, struct pnp_card_link *pcard
 
 	if (mpu_port[dev] > 0) {
 		if (snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
-					mpu_port[dev], 0, mpu_irq[dev], IRQF_DISABLED,
+					mpu_port[dev], 0, mpu_irq[dev],
 					NULL) < 0)
 			printk(KERN_ERR PFX "no MPU-401 device at 0x%lx.\n", mpu_port[dev]);
 	}

sound/isa/als100.c

@@ -256,7 +256,6 @@ static int __devinit snd_card_als100_probe(int dev,
 					mpu_type,
 					mpu_port[dev], 0, 
 					mpu_irq[dev],
-					mpu_irq[dev] >= 0 ? IRQF_DISABLED : 0,
 					NULL) < 0)
 			snd_printk(KERN_ERR PFX "no MPU-401 device at 0x%lx\n", mpu_port[dev]);
 	}

sound/isa/azt2320.c

@@ -234,8 +234,7 @@ static int __devinit snd_card_azt2320_probe(int dev,
 	if (mpu_port[dev] > 0 && mpu_port[dev] != SNDRV_AUTO_PORT) {
 		if (snd_mpu401_uart_new(card, 0, MPU401_HW_AZT2320,
 				mpu_port[dev], 0,
-				mpu_irq[dev], IRQF_DISABLED,
-				NULL) < 0)
+				mpu_irq[dev], NULL) < 0)
 			snd_printk(KERN_ERR PFX "no MPU-401 device at 0x%lx\n", mpu_port[dev]);
 	}
 

sound/isa/cmi8330.c

@@ -597,7 +597,7 @@ static int __devinit snd_cmi8330_probe(struct snd_card *card, int dev)
 	if (mpuport[dev] != SNDRV_AUTO_PORT) {
 		if (snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
 					mpuport[dev], 0, mpuirq[dev],
-					IRQF_DISABLED, NULL) < 0)
+					NULL) < 0)
 			printk(KERN_ERR PFX "no MPU-401 device at 0x%lx.\n",
 				mpuport[dev]);
 	}

sound/isa/cs423x/cs4231.c

@@ -131,7 +131,6 @@ static int __devinit snd_cs4231_probe(struct device *dev, unsigned int n)
 			mpu_irq[n] = -1;
 		if (snd_mpu401_uart_new(card, 0, MPU401_HW_CS4232,
 					mpu_port[n], 0, mpu_irq[n],
-					mpu_irq[n] >= 0 ? IRQF_DISABLED : 0,
 					NULL) < 0)
 			dev_warn(dev, "MPU401 not detected\n");
 	}

sound/isa/cs423x/cs4236.c

@@ -449,8 +449,7 @@ static int __devinit snd_cs423x_probe(struct snd_card *card, int dev)
 			mpu_irq[dev] = -1;
 		if (snd_mpu401_uart_new(card, 0, MPU401_HW_CS4232,
 					mpu_port[dev], 0,
-					mpu_irq[dev],
-					mpu_irq[dev] >= 0 ? IRQF_DISABLED : 0, NULL) < 0)
+					mpu_irq[dev], NULL) < 0)
 			printk(KERN_WARNING IDENT ": MPU401 not detected\n");
 	}
 

sound/isa/es1688/es1688.c

@@ -174,7 +174,7 @@ static int __devinit snd_es1688_probe(struct snd_card *card, unsigned int n)
 			chip->mpu_port > 0) {
 		error = snd_mpu401_uart_new(card, 0, MPU401_HW_ES1688,
 				chip->mpu_port, 0,
-				mpu_irq[n], IRQF_DISABLED, NULL);
+				mpu_irq[n], NULL);
 		if (error < 0)
 			return error;
 	}

sound/isa/es18xx.c

@@ -2160,8 +2160,8 @@ static int __devinit snd_audiodrive_probe(struct snd_card *card, int dev)
 
 	if (mpu_port[dev] > 0 && mpu_port[dev] != SNDRV_AUTO_PORT) {
 		err = snd_mpu401_uart_new(card, 0, MPU401_HW_ES18XX,
-					  mpu_port[dev], 0,
-					  irq[dev], 0, &chip->rmidi);
+					  mpu_port[dev], MPU401_INFO_IRQ_HOOK,
+					  -1, &chip->rmidi);
 		if (err < 0)
 			return err;
 	}

sound/isa/galaxy/galaxy.c

@@ -585,8 +585,7 @@ static int __devinit snd_galaxy_probe(struct device *dev, unsigned int n)
 
 	if (mpu_port[n] >= 0) {
 		err = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
-					  mpu_port[n], 0, mpu_irq[n],
-					  IRQF_DISABLED, NULL);
+					  mpu_port[n], 0, mpu_irq[n], NULL);
 		if (err < 0)
 			goto error;
 	}

sound/isa/gus/gusextreme.c

@@ -317,8 +317,7 @@ static int __devinit snd_gusextreme_probe(struct device *dev, unsigned int n)
 
 	if (es1688->mpu_port >= 0x300) {
 		error = snd_mpu401_uart_new(card, 0, MPU401_HW_ES1688,
-				es1688->mpu_port, 0,
-				mpu_irq[n], IRQF_DISABLED, NULL);
+				es1688->mpu_port, 0, mpu_irq[n], NULL);
 		if (error < 0)
 			goto out;
 	}

sound/isa/msnd/msnd_pinnacle.c

@@ -600,7 +600,7 @@ static int __devinit snd_msnd_attach(struct snd_card *card)
 					  mpu_io[0],
 					  MPU401_MODE_INPUT |
 					  MPU401_MODE_OUTPUT,
-					  mpu_irq[0], IRQF_DISABLED,
+					  mpu_irq[0],
 					  &chip->rmidi);
 		if (err < 0) {
 			printk(KERN_ERR LOGNAME

sound/isa/opl3sa2.c

@@ -707,8 +707,9 @@ static int __devinit snd_opl3sa2_probe(struct snd_card *card, int dev)
 	}
 	if (midi_port[dev] >= 0x300 && midi_port[dev] < 0x340) {
 		if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_OPL3SA2,
-					       midi_port[dev], 0,
-					       xirq, 0, &chip->rmidi)) < 0)
+					       midi_port[dev],
+					       MPU401_INFO_IRQ_HOOK, -1,
+					       &chip->rmidi)) < 0)
 			return err;
 	}
 	sprintf(card->longname, "%s at 0x%lx, irq %d, dma %d",

sound/isa/opti9xx/miro.c

@@ -1377,8 +1377,7 @@ static int __devinit snd_miro_probe(struct snd_card *card)
 		rmidi = NULL;
 	else {
 		error = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
-				mpu_port, 0, miro->mpu_irq, IRQF_DISABLED,
-				&rmidi);
+				mpu_port, 0, miro->mpu_irq, &rmidi);
 		if (error < 0)
 			snd_printk(KERN_WARNING "no MPU-401 device at 0x%lx?\n",
 				   mpu_port);

sound/isa/opti9xx/opti92x-ad1848.c

@@ -914,7 +914,7 @@ static int __devinit snd_opti9xx_probe(struct snd_card *card)
 		rmidi = NULL;
 	else {
 		error = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
-				mpu_port, 0, mpu_irq, IRQF_DISABLED, &rmidi);
+				mpu_port, 0, mpu_irq, &rmidi);
 		if (error)
 			snd_printk(KERN_WARNING "no MPU-401 device at 0x%lx?\n",
 				   mpu_port);

sound/isa/sb/jazz16.c

@@ -322,7 +322,6 @@ static int __devinit snd_jazz16_probe(struct device *devptr, unsigned int dev)
 					MPU401_HW_MPU401,
 					mpu_port[dev], 0,
 					mpu_irq[dev],
-					mpu_irq[dev] >= 0 ? IRQF_DISABLED : 0,
 					NULL) < 0)
 			snd_printk(KERN_ERR "no MPU-401 device at 0x%lx\n",
 					mpu_port[dev]);

sound/isa/sb/sb16.c

@@ -394,8 +394,9 @@ static int __devinit snd_sb16_probe(struct snd_card *card, int dev)
 
 	if (chip->mpu_port > 0 && chip->mpu_port != SNDRV_AUTO_PORT) {
 		if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_SB,
-					       chip->mpu_port, 0,
-					       xirq, 0, &chip->rmidi)) < 0)
+					       chip->mpu_port,
+					       MPU401_INFO_IRQ_HOOK, -1,
+					       &chip->rmidi)) < 0)
 			return err;
 		chip->rmidi_callback = snd_mpu401_uart_interrupt;
 	}

sound/isa/sc6000.c

@@ -658,8 +658,7 @@ static int __devinit snd_sc6000_probe(struct device *devptr, unsigned int dev)
 		if (snd_mpu401_uart_new(card, 0,
 					MPU401_HW_MPU401,
 					mpu_port[dev], 0,
-					mpu_irq[dev], IRQF_DISABLED,
-					NULL) < 0)
+					mpu_irq[dev], NULL) < 0)
 			snd_printk(KERN_ERR "no MPU-401 device at 0x%lx ?\n",
 					mpu_port[dev]);
 	}

sound/isa/sscape.c

@@ -825,8 +825,7 @@ static int __devinit create_mpu401(struct snd_card *card, int devnum,
 	int err;
 
 	err = snd_mpu401_uart_new(card, devnum, MPU401_HW_MPU401, port,
-				  MPU401_INFO_INTEGRATED, irq, IRQF_DISABLED,
-				  &rawmidi);
+				  MPU401_INFO_INTEGRATED, irq, &rawmidi);
 	if (err == 0) {
 		struct snd_mpu401 *mpu = rawmidi->private_data;
 		mpu->open_input = mpu401_open;

sound/isa/wavefront/wavefront.c

@@ -449,8 +449,7 @@ snd_wavefront_probe (struct snd_card *card, int dev)
 	if (cs4232_mpu_port[dev] > 0 && cs4232_mpu_port[dev] != SNDRV_AUTO_PORT) {
 		err = snd_mpu401_uart_new(card, midi_dev, MPU401_HW_CS4232,
 					  cs4232_mpu_port[dev], 0,
-					  cs4232_mpu_irq[dev], IRQF_DISABLED,
-					  NULL);
+					  cs4232_mpu_irq[dev], NULL);
 		if (err < 0) {
 			snd_printk (KERN_ERR "can't allocate CS4232 MPU-401 device\n");
 			return err;

sound/pci/als4000.c

@@ -931,8 +931,9 @@ static int __devinit snd_card_als4000_probe(struct pci_dev *pci,
 
 	if ((err = snd_mpu401_uart_new( card, 0, MPU401_HW_ALS4000,
 					iobase + ALS4K_IOB_30_MIDI_DATA,
-					MPU401_INFO_INTEGRATED,
-					pci->irq, 0, &chip->rmidi)) < 0) {
+					MPU401_INFO_INTEGRATED |
+					MPU401_INFO_IRQ_HOOK,
+					-1, &chip->rmidi)) < 0) {
 		printk(KERN_ERR "als4000: no MPU-401 device at 0x%lx?\n",
 				iobase + ALS4K_IOB_30_MIDI_DATA);
 		goto out_err;

sound/pci/au88x0/au88x0_mpu401.c

@@ -84,7 +84,7 @@ static int __devinit snd_vortex_midi(vortex_t * vortex)
 #ifdef VORTEX_MPU401_LEGACY
 	if ((temp =
 	     snd_mpu401_uart_new(vortex->card, 0, MPU401_HW_MPU401, 0x330,
-				 0, 0, 0, &rmidi)) != 0) {
+				 MPU401_INFO_IRQ_HOOK, -1, &rmidi)) != 0) {
 		hwwrite(vortex->mmio, VORTEX_CTRL,
 			(hwread(vortex->mmio, VORTEX_CTRL) &
 			 ~CTRL_MIDI_PORT) & ~CTRL_MIDI_EN);
@@ -94,8 +94,8 @@ static int __devinit snd_vortex_midi(vortex_t * vortex)
 	port = (unsigned long)(vortex->mmio + VORTEX_MIDI_DATA);
 	if ((temp =
 	     snd_mpu401_uart_new(vortex->card, 0, MPU401_HW_AUREAL, port,
-				 MPU401_INFO_INTEGRATED | MPU401_INFO_MMIO,
-				 0, 0, &rmidi)) != 0) {
+				 MPU401_INFO_INTEGRATED | MPU401_INFO_MMIO |
+				 MPU401_INFO_IRQ_HOOK, -1, &rmidi)) != 0) {
 		hwwrite(vortex->mmio, VORTEX_CTRL,
 			(hwread(vortex->mmio, VORTEX_CTRL) &
 			 ~CTRL_MIDI_PORT) & ~CTRL_MIDI_EN);

sound/pci/azt3328.c

@@ -2652,8 +2652,9 @@ snd_azf3328_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 	   since our hardware ought to be similar, thus use same ID. */
 	err = snd_mpu401_uart_new(
 		card, 0,
-		MPU401_HW_AZT2320, chip->mpu_io, MPU401_INFO_INTEGRATED,
-		pci->irq, 0, &chip->rmidi
+		MPU401_HW_AZT2320, chip->mpu_io,
+		MPU401_INFO_INTEGRATED | MPU401_INFO_IRQ_HOOK,
+		-1, &chip->rmidi
 	);
 	if (err < 0) {
 		snd_printk(KERN_ERR "azf3328: no MPU-401 device at 0x%lx?\n",

sound/pci/cmipci.c

@@ -3228,8 +3228,9 @@ static int __devinit snd_cmipci_create(struct snd_card *card, struct pci_dev *pc
 		if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_CMIPCI,
 					       iomidi,
 					       (integrated_midi ?
-						MPU401_INFO_INTEGRATED : 0),
-					       cm->irq, 0, &cm->rmidi)) < 0) {
+						MPU401_INFO_INTEGRATED : 0) |
+					       MPU401_INFO_IRQ_HOOK,
+					       -1, &cm->rmidi)) < 0) {
 			printk(KERN_ERR "cmipci: no UART401 device at 0x%lx\n", iomidi);
 		}
 	}

sound/pci/es1938.c

@@ -1854,8 +1854,9 @@ static int __devinit snd_es1938_probe(struct pci_dev *pci,
 		}
 	}
 	if (snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
-				chip->mpu_port, MPU401_INFO_INTEGRATED,
-				chip->irq, 0, &chip->rmidi) < 0) {
+				chip->mpu_port,
+				MPU401_INFO_INTEGRATED | MPU401_INFO_IRQ_HOOK,
+				-1, &chip->rmidi) < 0) {
 		printk(KERN_ERR "es1938: unable to initialize MPU-401\n");
 	} else {
 		// this line is vital for MIDI interrupt handling on ess-solo1

sound/pci/es1968.c

@@ -2843,8 +2843,9 @@ static int __devinit snd_es1968_probe(struct pci_dev *pci,
 	if (enable_mpu[dev]) {
 		if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_MPU401,
 					       chip->io_port + ESM_MPU401_PORT,
-					       MPU401_INFO_INTEGRATED,
-					       chip->irq, 0, &chip->rmidi)) < 0) {
+					       MPU401_INFO_INTEGRATED |
+					       MPU401_INFO_IRQ_HOOK,
+					       -1, &chip->rmidi)) < 0) {
 			printk(KERN_WARNING "es1968: skipping MPU-401 MIDI support..\n");
 		}
 	}

sound/pci/fm801.c

@@ -1306,8 +1306,9 @@ static int __devinit snd_card_fm801_probe(struct pci_dev *pci,
 	}
 	if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_FM801,
 				       FM801_REG(chip, MPU401_DATA),
-				       MPU401_INFO_INTEGRATED,
-				       chip->irq, 0, &chip->rmidi)) < 0) {
+				       MPU401_INFO_INTEGRATED |
+				       MPU401_INFO_IRQ_HOOK,
+				       -1, &chip->rmidi)) < 0) {
 		snd_card_free(card);
 		return err;
 	}

sound/pci/ice1712/ice1712.c

@@ -2748,8 +2748,9 @@ static int __devinit snd_ice1712_probe(struct pci_dev *pci,
 	if (!c->no_mpu401) {
 		err = snd_mpu401_uart_new(card, 0, MPU401_HW_ICE1712,
 			ICEREG(ice, MPU1_CTRL),
-			(c->mpu401_1_info_flags | MPU401_INFO_INTEGRATED),
-			ice->irq, 0, &ice->rmidi[0]);
+			c->mpu401_1_info_flags |
+			MPU401_INFO_INTEGRATED | MPU401_INFO_IRQ_HOOK,
+			-1, &ice->rmidi[0]);
 		if (err < 0) {
 			snd_card_free(card);
 			return err;
@@ -2764,8 +2765,9 @@ static int __devinit snd_ice1712_probe(struct pci_dev *pci,
 			/*  2nd port used  */
 			err = snd_mpu401_uart_new(card, 1, MPU401_HW_ICE1712,
 				ICEREG(ice, MPU2_CTRL),
-				(c->mpu401_2_info_flags | MPU401_INFO_INTEGRATED),
-				ice->irq, 0, &ice->rmidi[1]);
+				c->mpu401_2_info_flags |
+				MPU401_INFO_INTEGRATED | MPU401_INFO_IRQ_HOOK,
+				-1, &ice->rmidi[1]);
 
 			if (err < 0) {
 				snd_card_free(card);

sound/pci/maestro3.c

@@ -2820,8 +2820,8 @@ snd_m3_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 	/* TODO enable MIDI IRQ and I/O */
 	err = snd_mpu401_uart_new(chip->card, 0, MPU401_HW_MPU401,
 				  chip->iobase + MPU401_DATA_PORT,
-				  MPU401_INFO_INTEGRATED,
-				  chip->irq, 0, &chip->rmidi);
+				  MPU401_INFO_INTEGRATED | MPU401_INFO_IRQ_HOOK,
+				  -1, &chip->rmidi);
 	if (err < 0)
 		printk(KERN_WARNING "maestro3: no MIDI support.\n");
 #endif

sound/pci/oxygen/oxygen_lib.c

@@ -678,15 +678,15 @@ int oxygen_pci_probe(struct pci_dev *pci, int index, char *id,
 		goto err_card;
 
 	if (chip->model.device_config & (MIDI_OUTPUT | MIDI_INPUT)) {
-		unsigned int info_flags = MPU401_INFO_INTEGRATED;
+		unsigned int info_flags =
+				MPU401_INFO_INTEGRATED | MPU401_INFO_IRQ_HOOK;
 		if (chip->model.device_config & MIDI_OUTPUT)
 			info_flags |= MPU401_INFO_OUTPUT;
 		if (chip->model.device_config & MIDI_INPUT)
 			info_flags |= MPU401_INFO_INPUT;
 		err = snd_mpu401_uart_new(card, 0, MPU401_HW_CMIPCI,
 					  chip->addr + OXYGEN_MPU401,
-					  info_flags, 0, 0,
-					  &chip->midi);
+					  info_flags, -1, &chip->midi);
 		if (err < 0)
 			goto err_card;
 	}

sound/pci/riptide/riptide.c

@@ -2109,7 +2109,7 @@ snd_card_riptide_probe(struct pci_dev *pci, const struct pci_device_id *pci_id)
 		val = mpu_port[dev];
 		pci_write_config_word(chip->pci, PCI_EXT_MPU_Base, val);
 		err = snd_mpu401_uart_new(card, 0, MPU401_HW_RIPTIDE,
-					  val, 0, chip->irq, 0,
+					  val, MPU401_INFO_IRQ_HOOK, -1,
 					  &chip->rmidi);
 		if (err < 0)
 			snd_printk(KERN_WARNING

sound/pci/sonicvibes.c

@@ -1493,9 +1493,10 @@ static int __devinit snd_sonic_probe(struct pci_dev *pci,
 		return err;
 	}
 	if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_SONICVIBES,
-				       sonic->midi_port, MPU401_INFO_INTEGRATED,
-				       sonic->irq, 0,
-				       &midi_uart)) < 0) {
+				       sonic->midi_port,
+				       MPU401_INFO_INTEGRATED |
+				       MPU401_INFO_IRQ_HOOK,
+				       -1, &midi_uart)) < 0) {
 		snd_card_free(card);
 		return err;
 	}

sound/pci/trident/trident.c

@@ -148,8 +148,9 @@ static int __devinit snd_trident_probe(struct pci_dev *pci,
 	if (trident->device != TRIDENT_DEVICE_ID_SI7018 &&
 	    (err = snd_mpu401_uart_new(card, 0, MPU401_HW_TRID4DWAVE,
 				       trident->midi_port,
-				       MPU401_INFO_INTEGRATED,
-				       trident->irq, 0, &trident->rmidi)) < 0) {
+				       MPU401_INFO_INTEGRATED |
+				       MPU401_INFO_IRQ_HOOK,
+				       -1, &trident->rmidi)) < 0) {
 		snd_card_free(card);
 		return err;
 	}

sound/pci/via82xx.c

@@ -2068,8 +2068,9 @@ static int __devinit snd_via686_init_misc(struct via82xx *chip)
 	pci_write_config_byte(chip->pci, VIA_PNP_CONTROL, legacy_cfg);
 	if (chip->mpu_res) {
 		if (snd_mpu401_uart_new(chip->card, 0, MPU401_HW_VIA686A,
-					mpu_port, MPU401_INFO_INTEGRATED,
-					chip->irq, 0, &chip->rmidi) < 0) {
+					mpu_port, MPU401_INFO_INTEGRATED |
+					MPU401_INFO_IRQ_HOOK, -1,
+					&chip->rmidi) < 0) {
 			printk(KERN_WARNING "unable to initialize MPU-401"
 			       " at 0x%lx, skipping\n", mpu_port);
 			legacy &= ~VIA_FUNC_ENABLE_MIDI;

sound/pci/ymfpci/ymfpci.c

@@ -305,8 +305,9 @@ static int __devinit snd_card_ymfpci_probe(struct pci_dev *pci,
 	if (chip->mpu_res) {
 		if ((err = snd_mpu401_uart_new(card, 0, MPU401_HW_YMFPCI,
 					       mpu_port[dev],
-					       MPU401_INFO_INTEGRATED,
-					       pci->irq, 0, &chip->rawmidi)) < 0) {
+					       MPU401_INFO_INTEGRATED |
+					       MPU401_INFO_IRQ_HOOK,
+					       -1, &chip->rawmidi)) < 0) {
 			printk(KERN_WARNING "ymfpci: cannot initialize MPU401 at 0x%lx, skipping...\n", mpu_port[dev]);
 			legacy_ctrl &= ~YMFPCI_LEGACY_MIEN; /* disable MPU401 irq */
 			pci_write_config_word(pci, PCIR_DSXG_LEGACY, legacy_ctrl);