diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 141087cf3107..fd2bd56e7195 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device. Each node's name represents the name of the corresponding LED. LED sub-node properties: -- gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/devicetree/booting-without-of.txt. Active - low LEDs should be indicated using flags in the GPIO specifier. +- gpios : Should specify the LED's GPIO, see "gpios property" in + Documentation/devicetree/gpio.txt. Active low LEDs should be + indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). - linux,default-trigger : (optional) This parameter, if present, is a diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ecc6a6cd26c1..a20008ab319a 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -30,6 +30,7 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +picochip Picochip Ltd powervr Imagination Technologies qcom Qualcomm, Inc. ramtron Ramtron International diff --git a/Documentation/hwmon/jc42 b/Documentation/hwmon/jc42 index a22ecf48f255..52729a756c1b 100644 --- a/Documentation/hwmon/jc42 +++ b/Documentation/hwmon/jc42 @@ -7,21 +7,29 @@ Supported chips: Addresses scanned: I2C 0x18 - 0x1f Datasheets: http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf - * IDT TSE2002B3, TS3000B3 - Prefix: 'tse2002b3', 'ts3000b3' + * Atmel AT30TS00 + Prefix: 'at30ts00' Addresses scanned: I2C 0x18 - 0x1f Datasheets: - http://www.idt.com/products/getdoc.cfm?docid=18715691 - http://www.idt.com/products/getdoc.cfm?docid=18715692 + http://www.atmel.com/Images/doc8585.pdf + * IDT TSE2002B3, TSE2002GB2, TS3000B3, TS3000GB2 + Prefix: 'tse2002', 'ts3000' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.idt.com/sites/default/files/documents/IDT_TSE2002B3C_DST_20100512_120303152056.pdf + http://www.idt.com/sites/default/files/documents/IDT_TSE2002GB2A1_DST_20111107_120303145914.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000B3A_DST_20101129_120303152013.pdf + http://www.idt.com/sites/default/files/documents/IDT_TS3000GB2A1_DST_20111104_120303151012.pdf * Maxim MAX6604 Prefix: 'max6604' Addresses scanned: I2C 0x18 - 0x1f Datasheets: http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf - * Microchip MCP9805, MCP98242, MCP98243, MCP9843 - Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' + * Microchip MCP9804, MCP9805, MCP98242, MCP98243, MCP9843 + Prefixes: 'mcp9804', 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843' Addresses scanned: I2C 0x18 - 0x1f Datasheets: + http://ww1.microchip.com/downloads/en/DeviceDoc/22203C.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf @@ -48,6 +56,12 @@ Supported chips: Datasheets: http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf + * ST Microelectronics STTS2002, STTS3000 + Prefix: 'stts2002', 'stts3000' + Addresses scanned: I2C 0x18 - 0x1f + Datasheets: + http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATASHEET/CD00225278.pdf + http://www.st.com/internet/com/TECHNICAL_RESOURCES/TECHNICAL_LITERATURE/DATA_BRIEF/CD00270920.pdf * JEDEC JC 42.4 compliant temperature sensor chips Prefix: 'jc42' Addresses scanned: I2C 0x18 - 0x1f diff --git a/Documentation/input/alps.txt b/Documentation/input/alps.txt index f274c28b5103..2f95308251d4 100644 --- a/Documentation/input/alps.txt +++ b/Documentation/input/alps.txt @@ -13,7 +13,8 @@ Detection All ALPS touchpads should respond to the "E6 report" command sequence: E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or -00-00-64. +00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s +if some buttons are pressed. If the E6 report is successful, the touchpad model is identified using the "E7 report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 033d4e69b43b..d99fd9c0ec0e 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -2211,6 +2211,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted. default: off. + printk.always_kmsg_dump= + Trigger kmsg_dump for cases other than kernel oops or + panics + Format: (1/Y/y=enable, 0/N/n=disable) + default: disabled + printk.time= Show timing data prefixed to each printk message line Format: (1/Y/y=enable, 0/N/n=disable) diff --git a/MAINTAINERS b/MAINTAINERS index 9a648eb8e213..3321d75c6c7f 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -269,7 +269,6 @@ S: Orphan F: drivers/platform/x86/wmi.c AD1889 ALSA SOUND DRIVER -M: Kyle McMartin M: Thibaut Varene W: http://wiki.parisc-linux.org/AD1889 L: linux-parisc@vger.kernel.org @@ -963,7 +962,7 @@ F: drivers/tty/serial/msm_serial.c F: drivers/platform/msm/ F: drivers/*/pm8???-* F: include/linux/mfd/pm8xxx/ -T: git git://codeaurora.org/quic/kernel/davidb/linux-msm.git +T: git git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm.git S: Maintained ARM/TOSA MACHINE SUPPORT @@ -1311,7 +1310,7 @@ F: drivers/atm/ F: include/linux/atm* ATMEL AT91 MCI DRIVER -M: Nicolas Ferre +M: Ludovic Desroches L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) W: http://www.atmel.com/products/AT91/ W: http://www.at91.com/ @@ -1319,7 +1318,7 @@ S: Maintained F: drivers/mmc/host/at91_mci.c ATMEL AT91 / AT32 MCI DRIVER -M: Nicolas Ferre +M: Ludovic Desroches S: Maintained F: drivers/mmc/host/atmel-mci.c F: drivers/mmc/host/atmel-mci-regs.h @@ -3047,7 +3046,6 @@ F: drivers/hwspinlock/hwspinlock_* F: include/linux/hwspinlock.h HARMONY SOUND DRIVER -M: Kyle McMartin L: linux-parisc@vger.kernel.org S: Maintained F: sound/parisc/harmony.* @@ -3782,7 +3780,7 @@ F: Documentation/kdump/ KERNEL AUTOMOUNTER v4 (AUTOFS4) M: Ian Kent -L: autofs@linux.kernel.org +L: autofs@vger.kernel.org S: Maintained F: fs/autofs4/ @@ -4687,7 +4685,7 @@ NTFS FILESYSTEM M: Anton Altaparmakov L: linux-ntfs-dev@lists.sourceforge.net W: http://www.tuxera.com/ -T: git git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs-2.6.git +T: git git://git.kernel.org/pub/scm/linux/kernel/git/aia21/ntfs.git S: Supported F: Documentation/filesystems/ntfs.txt F: fs/ntfs/ @@ -5000,9 +4998,8 @@ F: Documentation/blockdev/paride.txt F: drivers/block/paride/ PARISC ARCHITECTURE -M: Kyle McMartin -M: Helge Deller M: "James E.J. Bottomley" +M: Helge Deller L: linux-parisc@vger.kernel.org W: http://www.parisc-linux.org/ Q: http://patchwork.kernel.org/project/linux-parisc/list/ @@ -5861,7 +5858,7 @@ S: Maintained F: drivers/mmc/host/sdhci-spear.c SECURITY SUBSYSTEM -M: James Morris +M: James Morris L: linux-security-module@vger.kernel.org (suggested Cc:) T: git git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security.git W: http://security.wiki.kernel.org/ @@ -5874,7 +5871,7 @@ S: Supported SELINUX SECURITY MODULE M: Stephen Smalley -M: James Morris +M: James Morris M: Eric Paris L: selinux@tycho.nsa.gov (subscribers-only, general discussion) W: http://selinuxproject.org @@ -7274,7 +7271,7 @@ WATCHDOG DEVICE DRIVERS M: Wim Van Sebroeck L: linux-watchdog@vger.kernel.org W: http://www.linux-watchdog.org/ -T: git git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog.git +T: git git://www.linux-watchdog.org/linux-watchdog.git S: Maintained F: Documentation/watchdog/ F: drivers/watchdog/ diff --git a/Makefile b/Makefile index 4ddd641ab615..56d481727c30 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 3 PATCHLEVEL = 3 SUBLEVEL = 0 -EXTRAVERSION = -rc4 +EXTRAVERSION = -rc7 NAME = Saber-toothed Squirrel # *DOCUMENTATION* diff --git a/arch/alpha/include/asm/futex.h b/arch/alpha/include/asm/futex.h index e8a761aee088..f939794363ac 100644 --- a/arch/alpha/include/asm/futex.h +++ b/arch/alpha/include/asm/futex.h @@ -108,7 +108,7 @@ futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr, " lda $31,3b-2b(%0)\n" " .previous\n" : "+r"(ret), "=&r"(prev), "=&r"(cmp) - : "r"(uaddr), "r"((long)oldval), "r"(newval) + : "r"(uaddr), "r"((long)(int)oldval), "r"(newval) : "memory"); *uval = prev; diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index a48aecc17eac..dfb0312f4e73 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -1280,7 +1280,7 @@ config ARM_ERRATA_743622 depends on CPU_V7 help This option enables the workaround for the 743622 Cortex-A9 - (r2p0..r2p2) erratum. Under very rare conditions, a faulty + (r2p*) erratum. Under very rare conditions, a faulty optimisation in the Cortex-A9 Store Buffer may lead to data corruption. This workaround sets a specific bit in the diagnostic register of the Cortex-A9 which disables the Store Buffer diff --git a/arch/arm/boot/.gitignore b/arch/arm/boot/.gitignore index ce1c5ff746e7..3c79f85975aa 100644 --- a/arch/arm/boot/.gitignore +++ b/arch/arm/boot/.gitignore @@ -3,3 +3,4 @@ zImage xipImage bootpImage uImage +*.dtb diff --git a/arch/arm/common/it8152.c b/arch/arm/common/it8152.c index d1bcd7b13ebc..fb1f1cfce60c 100644 --- a/arch/arm/common/it8152.c +++ b/arch/arm/common/it8152.c @@ -320,13 +320,6 @@ err0: return -EBUSY; } -/* - * If we set up a device for bus mastering, we need to check the latency - * timer as we don't have even crappy BIOSes to set it properly. - * The implementation is from arch/i386/pci/i386.c - */ -unsigned int pcibios_max_latency = 255; - /* ITE bridge requires setting latency timer to avoid early bus access termination by PCI bus master devices */ diff --git a/arch/arm/common/pl330.c b/arch/arm/common/pl330.c index d8e44a43047c..ff3ad2244824 100644 --- a/arch/arm/common/pl330.c +++ b/arch/arm/common/pl330.c @@ -1502,12 +1502,13 @@ int pl330_chan_ctrl(void *ch_id, enum pl330_chan_op op) struct pl330_thread *thrd = ch_id; struct pl330_dmac *pl330; unsigned long flags; - int ret = 0, active = thrd->req_running; + int ret = 0, active; if (!thrd || thrd->free || thrd->dmac->state == DYING) return -EINVAL; pl330 = thrd->dmac; + active = thrd->req_running; spin_lock_irqsave(&pl330->lock, flags); diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h index 62f8095d46de..23371b17b23e 100644 --- a/arch/arm/include/asm/assembler.h +++ b/arch/arm/include/asm/assembler.h @@ -137,6 +137,11 @@ disable_irq .endm + .macro save_and_disable_irqs_notrace, oldcpsr + mrs \oldcpsr, cpsr + disable_irq_notrace + .endm + /* * Restore interrupt state previously stored in a register. We don't * guarantee that this will preserve the flags. diff --git a/arch/arm/include/asm/hardware/pl330.h b/arch/arm/include/asm/hardware/pl330.h index 575fa8186ca0..c1821385abfa 100644 --- a/arch/arm/include/asm/hardware/pl330.h +++ b/arch/arm/include/asm/hardware/pl330.h @@ -41,7 +41,7 @@ enum pl330_dstcachectrl { DCCTRL1, /* Bufferable only */ DCCTRL2, /* Cacheable, but do not allocate */ DCCTRL3, /* Cacheable and bufferable, but do not allocate */ - DINVALID1 = 8, + DINVALID1, /* AWCACHE = 0x1000 */ DINVALID2, DCCTRL6, /* Cacheable write-through, allocate on writes only */ DCCTRL7, /* Cacheable write-back, allocate on writes only */ diff --git a/arch/arm/include/asm/pmu.h b/arch/arm/include/asm/pmu.h index b5a5be2536c1..90114faa9f3c 100644 --- a/arch/arm/include/asm/pmu.h +++ b/arch/arm/include/asm/pmu.h @@ -134,7 +134,7 @@ int __init armpmu_register(struct arm_pmu *armpmu, char *name, int type); u64 armpmu_event_update(struct perf_event *event, struct hw_perf_event *hwc, - int idx, int overflow); + int idx); int armpmu_event_set_period(struct perf_event *event, struct hw_perf_event *hwc, diff --git a/arch/arm/include/asm/processor.h b/arch/arm/include/asm/processor.h index ce280b8d613c..cb8d638924fd 100644 --- a/arch/arm/include/asm/processor.h +++ b/arch/arm/include/asm/processor.h @@ -22,6 +22,7 @@ #include #include #include +#include #ifdef __KERNEL__ #define STACK_TOP ((current->personality & ADDR_LIMIT_32BIT) ? \ diff --git a/arch/arm/kernel/ecard.c b/arch/arm/kernel/ecard.c index 4dd0edab6a65..1651d4950744 100644 --- a/arch/arm/kernel/ecard.c +++ b/arch/arm/kernel/ecard.c @@ -242,6 +242,7 @@ static void ecard_init_pgtables(struct mm_struct *mm) memcpy(dst_pgd, src_pgd, sizeof(pgd_t) * (EASI_SIZE / PGDIR_SIZE)); + vma.vm_flags = VM_EXEC; vma.vm_mm = mm; flush_tlb_range(&vma, IO_START, IO_START + IO_SIZE); diff --git a/arch/arm/kernel/perf_event.c b/arch/arm/kernel/perf_event.c index 5bb91bf3d47f..b2abfa18f137 100644 --- a/arch/arm/kernel/perf_event.c +++ b/arch/arm/kernel/perf_event.c @@ -180,7 +180,7 @@ armpmu_event_set_period(struct perf_event *event, u64 armpmu_event_update(struct perf_event *event, struct hw_perf_event *hwc, - int idx, int overflow) + int idx) { struct arm_pmu *armpmu = to_arm_pmu(event->pmu); u64 delta, prev_raw_count, new_raw_count; @@ -193,13 +193,7 @@ again: new_raw_count) != prev_raw_count) goto again; - new_raw_count &= armpmu->max_period; - prev_raw_count &= armpmu->max_period; - - if (overflow) - delta = armpmu->max_period - prev_raw_count + new_raw_count + 1; - else - delta = new_raw_count - prev_raw_count; + delta = (new_raw_count - prev_raw_count) & armpmu->max_period; local64_add(delta, &event->count); local64_sub(delta, &hwc->period_left); @@ -216,7 +210,7 @@ armpmu_read(struct perf_event *event) if (hwc->idx < 0) return; - armpmu_event_update(event, hwc, hwc->idx, 0); + armpmu_event_update(event, hwc, hwc->idx); } static void @@ -232,7 +226,7 @@ armpmu_stop(struct perf_event *event, int flags) if (!(hwc->state & PERF_HES_STOPPED)) { armpmu->disable(hwc, hwc->idx); barrier(); /* why? */ - armpmu_event_update(event, hwc, hwc->idx, 0); + armpmu_event_update(event, hwc, hwc->idx); hwc->state |= PERF_HES_STOPPED | PERF_HES_UPTODATE; } } @@ -518,7 +512,13 @@ __hw_perf_event_init(struct perf_event *event) hwc->config_base |= (unsigned long)mapping; if (!hwc->sample_period) { - hwc->sample_period = armpmu->max_period; + /* + * For non-sampling runs, limit the sample_period to half + * of the counter width. That way, the new counter value + * is far less likely to overtake the previous one unless + * you have some serious IRQ latency issues. + */ + hwc->sample_period = armpmu->max_period >> 1; hwc->last_period = hwc->sample_period; local64_set(&hwc->period_left, hwc->sample_period); } @@ -679,6 +679,28 @@ static void __init cpu_pmu_init(struct arm_pmu *armpmu) armpmu->type = ARM_PMU_DEVICE_CPU; } +/* + * PMU hardware loses all context when a CPU goes offline. + * When a CPU is hotplugged back in, since some hardware registers are + * UNKNOWN at reset, the PMU must be explicitly reset to avoid reading + * junk values out of them. + */ +static int __cpuinit pmu_cpu_notify(struct notifier_block *b, + unsigned long action, void *hcpu) +{ + if ((action & ~CPU_TASKS_FROZEN) != CPU_STARTING) + return NOTIFY_DONE; + + if (cpu_pmu && cpu_pmu->reset) + cpu_pmu->reset(NULL); + + return NOTIFY_OK; +} + +static struct notifier_block __cpuinitdata pmu_cpu_notifier = { + .notifier_call = pmu_cpu_notify, +}; + /* * CPU PMU identification and registration. */ @@ -730,6 +752,7 @@ init_hw_perf_events(void) pr_info("enabled with %s PMU driver, %d counters available\n", cpu_pmu->name, cpu_pmu->num_events); cpu_pmu_init(cpu_pmu); + register_cpu_notifier(&pmu_cpu_notifier); armpmu_register(cpu_pmu, "cpu", PERF_TYPE_RAW); } else { pr_info("no hardware support available\n"); diff --git a/arch/arm/kernel/perf_event_v6.c b/arch/arm/kernel/perf_event_v6.c index 533be9930ec2..b78af0cc6ef3 100644 --- a/arch/arm/kernel/perf_event_v6.c +++ b/arch/arm/kernel/perf_event_v6.c @@ -467,23 +467,6 @@ armv6pmu_enable_event(struct hw_perf_event *hwc, raw_spin_unlock_irqrestore(&events->pmu_lock, flags); } -static int counter_is_active(unsigned long pmcr, int idx) -{ - unsigned long mask = 0; - if (idx == ARMV6_CYCLE_COUNTER) - mask = ARMV6_PMCR_CCOUNT_IEN; - else if (idx == ARMV6_COUNTER0) - mask = ARMV6_PMCR_COUNT0_IEN; - else if (idx == ARMV6_COUNTER1) - mask = ARMV6_PMCR_COUNT1_IEN; - - if (mask) - return pmcr & mask; - - WARN_ONCE(1, "invalid counter number (%d)\n", idx); - return 0; -} - static irqreturn_t armv6pmu_handle_irq(int irq_num, void *dev) @@ -513,7 +496,8 @@ armv6pmu_handle_irq(int irq_num, struct perf_event *event = cpuc->events[idx]; struct hw_perf_event *hwc; - if (!counter_is_active(pmcr, idx)) + /* Ignore if we don't have an event. */ + if (!event) continue; /* @@ -524,7 +508,7 @@ armv6pmu_handle_irq(int irq_num, continue; hwc = &event->hw; - armpmu_event_update(event, hwc, idx, 1); + armpmu_event_update(event, hwc, idx); data.period = event->hw.last_period; if (!armpmu_event_set_period(event, hwc, idx)) continue; diff --git a/arch/arm/kernel/perf_event_v7.c b/arch/arm/kernel/perf_event_v7.c index 6933244c68f9..4d7095af2ab3 100644 --- a/arch/arm/kernel/perf_event_v7.c +++ b/arch/arm/kernel/perf_event_v7.c @@ -809,6 +809,11 @@ static inline int armv7_pmnc_disable_intens(int idx) counter = ARMV7_IDX_TO_COUNTER(idx); asm volatile("mcr p15, 0, %0, c9, c14, 2" : : "r" (BIT(counter))); + isb(); + /* Clear the overflow flag in case an interrupt is pending. */ + asm volatile("mcr p15, 0, %0, c9, c12, 3" : : "r" (BIT(counter))); + isb(); + return idx; } @@ -955,6 +960,10 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev) struct perf_event *event = cpuc->events[idx]; struct hw_perf_event *hwc; + /* Ignore if we don't have an event. */ + if (!event) + continue; + /* * We have a single interrupt for all counters. Check that * each counter has overflowed before we process it. @@ -963,7 +972,7 @@ static irqreturn_t armv7pmu_handle_irq(int irq_num, void *dev) continue; hwc = &event->hw; - armpmu_event_update(event, hwc, idx, 1); + armpmu_event_update(event, hwc, idx); data.period = event->hw.last_period; if (!armpmu_event_set_period(event, hwc, idx)) continue; diff --git a/arch/arm/kernel/perf_event_xscale.c b/arch/arm/kernel/perf_event_xscale.c index 3b99d8269829..71a21e6712f5 100644 --- a/arch/arm/kernel/perf_event_xscale.c +++ b/arch/arm/kernel/perf_event_xscale.c @@ -255,11 +255,14 @@ xscale1pmu_handle_irq(int irq_num, void *dev) struct perf_event *event = cpuc->events[idx]; struct hw_perf_event *hwc; + if (!event) + continue; + if (!xscale1_pmnc_counter_has_overflowed(pmnc, idx)) continue; hwc = &event->hw; - armpmu_event_update(event, hwc, idx, 1); + armpmu_event_update(event, hwc, idx); data.period = event->hw.last_period; if (!armpmu_event_set_period(event, hwc, idx)) continue; @@ -592,11 +595,14 @@ xscale2pmu_handle_irq(int irq_num, void *dev) struct perf_event *event = cpuc->events[idx]; struct hw_perf_event *hwc; - if (!xscale2_pmnc_counter_has_overflowed(pmnc, idx)) + if (!event) + continue; + + if (!xscale2_pmnc_counter_has_overflowed(of_flags, idx)) continue; hwc = &event->hw; - armpmu_event_update(event, hwc, idx, 1); + armpmu_event_update(event, hwc, idx); data.period = event->hw.last_period; if (!armpmu_event_set_period(event, hwc, idx)) continue; @@ -663,7 +669,7 @@ xscale2pmu_enable_event(struct hw_perf_event *hwc, int idx) static void xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx) { - unsigned long flags, ien, evtsel; + unsigned long flags, ien, evtsel, of_flags; struct pmu_hw_events *events = cpu_pmu->get_hw_events(); ien = xscale2pmu_read_int_enable(); @@ -672,26 +678,31 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx) switch (idx) { case XSCALE_CYCLE_COUNTER: ien &= ~XSCALE2_CCOUNT_INT_EN; + of_flags = XSCALE2_CCOUNT_OVERFLOW; break; case XSCALE_COUNTER0: ien &= ~XSCALE2_COUNT0_INT_EN; evtsel &= ~XSCALE2_COUNT0_EVT_MASK; evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT0_EVT_SHFT; + of_flags = XSCALE2_COUNT0_OVERFLOW; break; case XSCALE_COUNTER1: ien &= ~XSCALE2_COUNT1_INT_EN; evtsel &= ~XSCALE2_COUNT1_EVT_MASK; evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT1_EVT_SHFT; + of_flags = XSCALE2_COUNT1_OVERFLOW; break; case XSCALE_COUNTER2: ien &= ~XSCALE2_COUNT2_INT_EN; evtsel &= ~XSCALE2_COUNT2_EVT_MASK; evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT2_EVT_SHFT; + of_flags = XSCALE2_COUNT2_OVERFLOW; break; case XSCALE_COUNTER3: ien &= ~XSCALE2_COUNT3_INT_EN; evtsel &= ~XSCALE2_COUNT3_EVT_MASK; evtsel |= XSCALE_PERFCTR_UNUSED << XSCALE2_COUNT3_EVT_SHFT; + of_flags = XSCALE2_COUNT3_OVERFLOW; break; default: WARN_ONCE(1, "invalid counter number (%d)\n", idx); @@ -701,6 +712,7 @@ xscale2pmu_disable_event(struct hw_perf_event *hwc, int idx) raw_spin_lock_irqsave(&events->pmu_lock, flags); xscale2pmu_write_event_select(evtsel); xscale2pmu_write_int_enable(ien); + xscale2pmu_write_overflow_flags(of_flags); raw_spin_unlock_irqrestore(&events->pmu_lock, flags); } diff --git a/arch/arm/kernel/ptrace.c b/arch/arm/kernel/ptrace.c index e33870ff0ac0..ede6443c34d9 100644 --- a/arch/arm/kernel/ptrace.c +++ b/arch/arm/kernel/ptrace.c @@ -23,6 +23,7 @@ #include #include #include +#include #include #include @@ -904,6 +905,12 @@ long arch_ptrace(struct task_struct *child, long request, return ret; } +#ifdef __ARMEB__ +#define AUDIT_ARCH_NR AUDIT_ARCH_ARMEB +#else +#define AUDIT_ARCH_NR AUDIT_ARCH_ARM +#endif + asmlinkage int syscall_trace(int why, struct pt_regs *regs, int scno) { unsigned long ip; @@ -918,7 +925,7 @@ asmlinkage int syscall_trace(int why, struct pt_regs *regs, int scno) if (!ip) audit_syscall_exit(regs); else - audit_syscall_entry(AUDIT_ARCH_ARMEB, scno, regs->ARM_r0, + audit_syscall_entry(AUDIT_ARCH_NR, scno, regs->ARM_r0, regs->ARM_r1, regs->ARM_r2, regs->ARM_r3); if (!test_thread_flag(TIF_SYSCALL_TRACE)) diff --git a/arch/arm/kernel/smp_twd.c b/arch/arm/kernel/smp_twd.c index 4285daa077b0..7a79b24597b2 100644 --- a/arch/arm/kernel/smp_twd.c +++ b/arch/arm/kernel/smp_twd.c @@ -129,7 +129,7 @@ static struct notifier_block twd_cpufreq_nb = { static int twd_cpufreq_init(void) { - if (!IS_ERR(twd_clk)) + if (twd_evt && *__this_cpu_ptr(twd_evt) && !IS_ERR(twd_clk)) return cpufreq_register_notifier(&twd_cpufreq_nb, CPUFREQ_TRANSITION_NOTIFIER); diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c index b7582dd10dc3..96e2adcd5a84 100644 --- a/arch/arm/mach-at91/at91sam9g45_devices.c +++ b/arch/arm/mach-at91/at91sam9g45_devices.c @@ -38,10 +38,6 @@ #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE) static u64 hdmac_dmamask = DMA_BIT_MASK(32); -static struct at_dma_platform_data atdma_pdata = { - .nr_channels = 8, -}; - static struct resource hdmac_resources[] = { [0] = { .start = AT91SAM9G45_BASE_DMA, @@ -56,12 +52,11 @@ static struct resource hdmac_resources[] = { }; static struct platform_device at_hdmac_device = { - .name = "at_hdmac", + .name = "at91sam9g45_dma", .id = -1, .dev = { .dma_mask = &hdmac_dmamask, .coherent_dma_mask = DMA_BIT_MASK(32), - .platform_data = &atdma_pdata, }, .resource = hdmac_resources, .num_resources = ARRAY_SIZE(hdmac_resources), @@ -69,9 +64,15 @@ static struct platform_device at_hdmac_device = { void __init at91_add_device_hdmac(void) { - dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask); - dma_cap_set(DMA_SLAVE, atdma_pdata.cap_mask); - platform_device_register(&at_hdmac_device); +#if defined(CONFIG_OF) + struct device_node *of_node = + of_find_node_by_name(NULL, "dma-controller"); + + if (of_node) + of_node_put(of_node); + else +#endif + platform_device_register(&at_hdmac_device); } #else void __init at91_add_device_hdmac(void) {} diff --git a/arch/arm/mach-at91/at91sam9rl_devices.c b/arch/arm/mach-at91/at91sam9rl_devices.c index 61908dce9784..9be71c11d0f0 100644 --- a/arch/arm/mach-at91/at91sam9rl_devices.c +++ b/arch/arm/mach-at91/at91sam9rl_devices.c @@ -33,10 +33,6 @@ #if defined(CONFIG_AT_HDMAC) || defined(CONFIG_AT_HDMAC_MODULE) static u64 hdmac_dmamask = DMA_BIT_MASK(32); -static struct at_dma_platform_data atdma_pdata = { - .nr_channels = 2, -}; - static struct resource hdmac_resources[] = { [0] = { .start = AT91SAM9RL_BASE_DMA, @@ -51,12 +47,11 @@ static struct resource hdmac_resources[] = { }; static struct platform_device at_hdmac_device = { - .name = "at_hdmac", + .name = "at91sam9rl_dma", .id = -1, .dev = { .dma_mask = &hdmac_dmamask, .coherent_dma_mask = DMA_BIT_MASK(32), - .platform_data = &atdma_pdata, }, .resource = hdmac_resources, .num_resources = ARRAY_SIZE(hdmac_resources), @@ -64,7 +59,6 @@ static struct platform_device at_hdmac_device = { void __init at91_add_device_hdmac(void) { - dma_cap_set(DMA_MEMCPY, atdma_pdata.cap_mask); platform_device_register(&at_hdmac_device); } #else diff --git a/arch/arm/mach-ep93xx/vision_ep9307.c b/arch/arm/mach-ep93xx/vision_ep9307.c index d5fb44f16d31..d67d0b4feb6f 100644 --- a/arch/arm/mach-ep93xx/vision_ep9307.c +++ b/arch/arm/mach-ep93xx/vision_ep9307.c @@ -34,6 +34,7 @@ #include #include +#include #include #include #include @@ -361,6 +362,7 @@ MACHINE_START(VISION_EP9307, "Vision Engraving Systems EP9307") .atag_offset = 0x100, .map_io = vision_map_io, .init_irq = ep93xx_init_irq, + .handle_irq = vic_handle_irq, .timer = &ep93xx_timer, .init_machine = vision_init_machine, .restart = ep93xx_restart, diff --git a/arch/arm/mach-exynos/mach-universal_c210.c b/arch/arm/mach-exynos/mach-universal_c210.c index 0fc65ffde8ff..38939956c34f 100644 --- a/arch/arm/mach-exynos/mach-universal_c210.c +++ b/arch/arm/mach-exynos/mach-universal_c210.c @@ -13,6 +13,7 @@ #include #include #include +#include #include #include #include @@ -595,6 +596,7 @@ static struct mxt_platform_data qt602240_platform_data = { .threshold = 0x28, .voltage = 2800000, /* 2.8V */ .orient = MXT_DIAGONAL, + .irqflags = IRQF_TRIGGER_FALLING, }; static struct i2c_board_info i2c3_devs[] __initdata = { diff --git a/arch/arm/mach-lpc32xx/include/mach/irqs.h b/arch/arm/mach-lpc32xx/include/mach/irqs.h index 2667f52e3b04..9e3b90df32e1 100644 --- a/arch/arm/mach-lpc32xx/include/mach/irqs.h +++ b/arch/arm/mach-lpc32xx/include/mach/irqs.h @@ -61,7 +61,7 @@ */ #define IRQ_LPC32XX_JTAG_COMM_TX LPC32XX_SIC1_IRQ(1) #define IRQ_LPC32XX_JTAG_COMM_RX LPC32XX_SIC1_IRQ(2) -#define IRQ_LPC32XX_GPI_11 LPC32XX_SIC1_IRQ(4) +#define IRQ_LPC32XX_GPI_28 LPC32XX_SIC1_IRQ(4) #define IRQ_LPC32XX_TS_P LPC32XX_SIC1_IRQ(6) #define IRQ_LPC32XX_TS_IRQ LPC32XX_SIC1_IRQ(7) #define IRQ_LPC32XX_TS_AUX LPC32XX_SIC1_IRQ(8) diff --git a/arch/arm/mach-lpc32xx/irq.c b/arch/arm/mach-lpc32xx/irq.c index 4eae566dfdc7..c74de01ab5b6 100644 --- a/arch/arm/mach-lpc32xx/irq.c +++ b/arch/arm/mach-lpc32xx/irq.c @@ -118,6 +118,10 @@ static const struct lpc32xx_event_info lpc32xx_events[NR_IRQS] = { .event_group = &lpc32xx_event_pin_regs, .mask = LPC32XX_CLKPWR_EXTSRC_GPI_06_BIT, }, + [IRQ_LPC32XX_GPI_28] = { + .event_group = &lpc32xx_event_pin_regs, + .mask = LPC32XX_CLKPWR_EXTSRC_GPI_28_BIT, + }, [IRQ_LPC32XX_GPIO_00] = { .event_group = &lpc32xx_event_int_regs, .mask = LPC32XX_CLKPWR_INTSRC_GPIO_00_BIT, @@ -305,9 +309,18 @@ static int lpc32xx_irq_wake(struct irq_data *d, unsigned int state) if (state) eventreg |= lpc32xx_events[d->irq].mask; - else + else { eventreg &= ~lpc32xx_events[d->irq].mask; + /* + * When disabling the wakeup, clear the latched + * event + */ + __raw_writel(lpc32xx_events[d->irq].mask, + lpc32xx_events[d->irq]. + event_group->rawstat_reg); + } + __raw_writel(eventreg, lpc32xx_events[d->irq].event_group->enab_reg); @@ -380,13 +393,15 @@ void __init lpc32xx_init_irq(void) /* Setup SIC1 */ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC1_BASE)); - __raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE)); - __raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE)); + __raw_writel(SIC1_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC1_BASE)); + __raw_writel(SIC1_ATR_DEFAULT, + LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC1_BASE)); /* Setup SIC2 */ __raw_writel(0, LPC32XX_INTC_MASK(LPC32XX_SIC2_BASE)); - __raw_writel(MIC_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE)); - __raw_writel(MIC_ATR_DEFAULT, LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE)); + __raw_writel(SIC2_APR_DEFAULT, LPC32XX_INTC_POLAR(LPC32XX_SIC2_BASE)); + __raw_writel(SIC2_ATR_DEFAULT, + LPC32XX_INTC_ACT_TYPE(LPC32XX_SIC2_BASE)); /* Configure supported IRQ's */ for (i = 0; i < NR_IRQS; i++) { diff --git a/arch/arm/mach-lpc32xx/serial.c b/arch/arm/mach-lpc32xx/serial.c index 429cfdbb2b3d..f2735281616a 100644 --- a/arch/arm/mach-lpc32xx/serial.c +++ b/arch/arm/mach-lpc32xx/serial.c @@ -88,6 +88,7 @@ struct uartinit { char *uart_ck_name; u32 ck_mode_mask; void __iomem *pdiv_clk_reg; + resource_size_t mapbase; }; static struct uartinit uartinit_data[] __initdata = { @@ -97,6 +98,7 @@ static struct uartinit uartinit_data[] __initdata = { .ck_mode_mask = LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 5), .pdiv_clk_reg = LPC32XX_CLKPWR_UART5_CLK_CTRL, + .mapbase = LPC32XX_UART5_BASE, }, #endif #ifdef CONFIG_ARCH_LPC32XX_UART3_SELECT @@ -105,6 +107,7 @@ static struct uartinit uartinit_data[] __initdata = { .ck_mode_mask = LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 3), .pdiv_clk_reg = LPC32XX_CLKPWR_UART3_CLK_CTRL, + .mapbase = LPC32XX_UART3_BASE, }, #endif #ifdef CONFIG_ARCH_LPC32XX_UART4_SELECT @@ -113,6 +116,7 @@ static struct uartinit uartinit_data[] __initdata = { .ck_mode_mask = LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 4), .pdiv_clk_reg = LPC32XX_CLKPWR_UART4_CLK_CTRL, + .mapbase = LPC32XX_UART4_BASE, }, #endif #ifdef CONFIG_ARCH_LPC32XX_UART6_SELECT @@ -121,6 +125,7 @@ static struct uartinit uartinit_data[] __initdata = { .ck_mode_mask = LPC32XX_UART_CLKMODE_LOAD(LPC32XX_UART_CLKMODE_ON, 6), .pdiv_clk_reg = LPC32XX_CLKPWR_UART6_CLK_CTRL, + .mapbase = LPC32XX_UART6_BASE, }, #endif }; @@ -165,11 +170,24 @@ void __init lpc32xx_serial_init(void) /* pre-UART clock divider set to 1 */ __raw_writel(0x0101, uartinit_data[i].pdiv_clk_reg); + + /* + * Force a flush of the RX FIFOs to work around a + * HW bug + */ + puart = uartinit_data[i].mapbase; + __raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart)); + __raw_writel(0x00, LPC32XX_UART_DLL_FIFO(puart)); + j = LPC32XX_SUART_FIFO_SIZE; + while (j--) + tmp = __raw_readl( + LPC32XX_UART_DLL_FIFO(puart)); + __raw_writel(0, LPC32XX_UART_IIR_FCR(puart)); } /* This needs to be done after all UART clocks are setup */ __raw_writel(clkmodes, LPC32XX_UARTCTL_CLKMODE); - for (i = 0; i < ARRAY_SIZE(uartinit_data) - 1; i++) { + for (i = 0; i < ARRAY_SIZE(uartinit_data); i++) { /* Force a flush of the RX FIFOs to work around a HW bug */ puart = serial_std_platform_data[i].mapbase; __raw_writel(0xC1, LPC32XX_UART_IIR_FCR(puart)); diff --git a/arch/arm/mach-mmp/aspenite.c b/arch/arm/mach-mmp/aspenite.c index 17cb76060125..3588a5584153 100644 --- a/arch/arm/mach-mmp/aspenite.c +++ b/arch/arm/mach-mmp/aspenite.c @@ -17,7 +17,6 @@ #include #include #include -#include #include #include diff --git a/arch/arm/mach-mmp/pxa168.c b/arch/arm/mach-mmp/pxa168.c index 7bc17eaa12eb..ada1213982b4 100644 --- a/arch/arm/mach-mmp/pxa168.c +++ b/arch/arm/mach-mmp/pxa168.c @@ -24,7 +24,6 @@ #include #include #include -#include #include #include diff --git a/arch/arm/mach-mmp/tavorevb.c b/arch/arm/mach-mmp/tavorevb.c index 8e3b5af04a57..bc97170125bf 100644 --- a/arch/arm/mach-mmp/tavorevb.c +++ b/arch/arm/mach-mmp/tavorevb.c @@ -12,7 +12,6 @@ #include #include #include -#include #include #include diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c index 309369ea6978..be2002f42dea 100644 --- a/arch/arm/mach-omap1/board-innovator.c +++ b/arch/arm/mach-omap1/board-innovator.c @@ -416,13 +416,13 @@ static void __init innovator_init(void) #ifdef CONFIG_ARCH_OMAP15XX if (cpu_is_omap1510()) { omap1_usb_init(&innovator1510_usb_config); - innovator_config[1].data = &innovator1510_lcd_config; + innovator_config[0].data = &innovator1510_lcd_config; } #endif #ifdef CONFIG_ARCH_OMAP16XX if (cpu_is_omap1610()) { omap1_usb_init(&h2_usb_config); - innovator_config[1].data = &innovator1610_lcd_config; + innovator_config[0].data = &innovator1610_lcd_config; } #endif omap_board_config = innovator_config; diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index d965da45160e..e20c8ab80b0e 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -364,8 +364,8 @@ config OMAP3_SDRC_AC_TIMING going on could result in system crashes; config OMAP4_ERRATA_I688 - bool "OMAP4 errata: Async Bridge Corruption (BROKEN)" - depends on ARCH_OMAP4 && BROKEN + bool "OMAP4 errata: Async Bridge Corruption" + depends on ARCH_OMAP4 select ARCH_HAS_BARRIERS help If a data is stalled inside asynchronous bridge because of back diff --git a/arch/arm/mach-omap2/board-n8x0.c b/arch/arm/mach-omap2/board-n8x0.c index 42a4d11fad23..672262717601 100644 --- a/arch/arm/mach-omap2/board-n8x0.c +++ b/arch/arm/mach-omap2/board-n8x0.c @@ -371,7 +371,11 @@ static void n8x0_mmc_callback(void *data, u8 card_mask) else *openp = 0; +#ifdef CONFIG_MMC_OMAP omap_mmc_notify_cover_event(mmc_device, index, *openp); +#else + pr_warn("MMC: notify cover event not available\n"); +#endif } static int n8x0_mmc_late_init(struct device *dev) diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index c775bead1497..c877236a8442 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -381,7 +381,7 @@ static int omap3evm_twl_gpio_setup(struct device *dev, gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI"); /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */ - gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; + gpio_leds[0].gpio = gpio + TWL4030_GPIO_MAX + 1; platform_device_register(&leds_gpio); diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h index febffde2ff10..7e9338e8d684 100644 --- a/arch/arm/mach-omap2/common.h +++ b/arch/arm/mach-omap2/common.h @@ -132,6 +132,7 @@ void omap3_map_io(void); void am33xx_map_io(void); void omap4_map_io(void); void ti81xx_map_io(void); +void omap_barriers_init(void); /** * omap_test_timeout - busy-loop, testing a condition diff --git a/arch/arm/mach-omap2/cpuidle44xx.c b/arch/arm/mach-omap2/cpuidle44xx.c index cfdbb86bc84e..72e018b9b260 100644 --- a/arch/arm/mach-omap2/cpuidle44xx.c +++ b/arch/arm/mach-omap2/cpuidle44xx.c @@ -65,7 +65,6 @@ static int omap4_enter_idle(struct cpuidle_device *dev, struct timespec ts_preidle, ts_postidle, ts_idle; u32 cpu1_state; int idle_time; - int new_state_idx; int cpu_id = smp_processor_id(); /* Used to keep track of the total time in idle */ @@ -84,8 +83,8 @@ static int omap4_enter_idle(struct cpuidle_device *dev, */ cpu1_state = pwrdm_read_pwrst(cpu1_pd); if (cpu1_state != PWRDM_POWER_OFF) { - new_state_idx = drv->safe_state_index; - cx = cpuidle_get_statedata(&dev->states_usage[new_state_idx]); + index = drv->safe_state_index; + cx = cpuidle_get_statedata(&dev->states_usage[index]); } if (index > 0) diff --git a/arch/arm/mach-omap2/gpmc-smsc911x.c b/arch/arm/mach-omap2/gpmc-smsc911x.c index 997033129d26..bbb870c04a5e 100644 --- a/arch/arm/mach-omap2/gpmc-smsc911x.c +++ b/arch/arm/mach-omap2/gpmc-smsc911x.c @@ -19,6 +19,8 @@ #include #include #include +#include +#include #include #include @@ -42,6 +44,50 @@ static struct smsc911x_platform_config gpmc_smsc911x_config = { .flags = SMSC911X_USE_16BIT, }; +static struct regulator_consumer_supply gpmc_smsc911x_supply[] = { + REGULATOR_SUPPLY("vddvario", "smsc911x.0"), + REGULATOR_SUPPLY("vdd33a", "smsc911x.0"), +}; + +/* Generic regulator definition to satisfy smsc911x */ +static struct regulator_init_data gpmc_smsc911x_reg_init_data = { + .constraints = { + .min_uV = 3300000, + .max_uV = 3300000, + .valid_modes_mask = REGULATOR_MODE_NORMAL + | REGULATOR_MODE_STANDBY, + .valid_ops_mask = REGULATOR_CHANGE_MODE + | REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(gpmc_smsc911x_supply), + .consumer_supplies = gpmc_smsc911x_supply, +}; + +static struct fixed_voltage_config gpmc_smsc911x_fixed_reg_data = { + .supply_name = "gpmc_smsc911x", + .microvolts = 3300000, + .gpio = -EINVAL, + .startup_delay = 0, + .enable_high = 0, + .enabled_at_boot = 1, + .init_data = &gpmc_smsc911x_reg_init_data, +}; + +/* + * Platform device id of 42 is a temporary fix to avoid conflicts + * with other reg-fixed-voltage devices. The real fix should + * involve the driver core providing a way of dynamically + * assigning a unique id on registration for platform devices + * in the same name space. + */ +static struct platform_device gpmc_smsc911x_regulator = { + .name = "reg-fixed-voltage", + .id = 42, + .dev = { + .platform_data = &gpmc_smsc911x_fixed_reg_data, + }, +}; + /* * Initialize smsc911x device connected to the GPMC. Note that we * assume that pin multiplexing is done in the board-*.c file, @@ -55,6 +101,12 @@ void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *board_data) gpmc_cfg = board_data; + ret = platform_device_register(&gpmc_smsc911x_regulator); + if (ret < 0) { + pr_err("Unable to register smsc911x regulators: %d\n", ret); + return; + } + if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) { pr_err("Failed to request GPMC mem region\n"); return; diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index b40c28895298..19dd1657245c 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -428,6 +428,7 @@ static int omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c, return 0; } +static int omap_hsmmc_done; #define MAX_OMAP_MMC_HWMOD_NAME_LEN 16 void omap_init_hsmmc(struct omap2_hsmmc_info *hsmmcinfo, int ctrl_nr) @@ -491,6 +492,11 @@ void omap2_hsmmc_init(struct omap2_hsmmc_info *controllers) { u32 reg; + if (omap_hsmmc_done) + return; + + omap_hsmmc_done = 1; + if (!cpu_is_omap44xx()) { if (cpu_is_omap2430()) { control_pbias_offset = OMAP243X_CONTROL_PBIAS_LITE; diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index 6c5826605eae..719ee423abe2 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -343,6 +343,7 @@ static void __init omap3_check_revision(const char **cpu_rev) case 0xb944: omap_revision = AM335X_REV_ES1_0; *cpu_rev = "1.0"; + break; case 0xb8f2: switch (rev) { case 0: diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index eb50c29fb644..fb11b44fbdec 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -307,6 +307,7 @@ void __init omapam33xx_map_common_io(void) void __init omap44xx_map_common_io(void) { iotable_init(omap44xx_io_desc, ARRAY_SIZE(omap44xx_io_desc)); + omap_barriers_init(); } #endif diff --git a/arch/arm/mach-omap2/mailbox.c b/arch/arm/mach-omap2/mailbox.c index 609ea2ded7e3..415a6f1cf419 100644 --- a/arch/arm/mach-omap2/mailbox.c +++ b/arch/arm/mach-omap2/mailbox.c @@ -281,8 +281,16 @@ static struct omap_mbox mbox_iva_info = { .ops = &omap2_mbox_ops, .priv = &omap2_mbox_iva_priv, }; +#endif -struct omap_mbox *omap2_mboxes[] = { &mbox_dsp_info, &mbox_iva_info, NULL }; +#ifdef CONFIG_ARCH_OMAP2 +struct omap_mbox *omap2_mboxes[] = { + &mbox_dsp_info, +#ifdef CONFIG_SOC_OMAP2420 + &mbox_iva_info, +#endif + NULL +}; #endif #if defined(CONFIG_ARCH_OMAP4) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index fb8bc9fa43b1..611a0e3d54ca 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -218,7 +218,7 @@ static int _omap_mux_get_by_name(struct omap_mux_partition *partition, return -ENODEV; } -static int __init +static int omap_mux_get_by_name(const char *muxname, struct omap_mux_partition **found_partition, struct omap_mux **found_mux) diff --git a/arch/arm/mach-omap2/omap-iommu.c b/arch/arm/mach-omap2/omap-iommu.c index b8822048e409..ac49384d0285 100644 --- a/arch/arm/mach-omap2/omap-iommu.c +++ b/arch/arm/mach-omap2/omap-iommu.c @@ -150,7 +150,8 @@ err_out: platform_device_put(omap_iommu_pdev[i]); return err; } -module_init(omap_iommu_init); +/* must be ready before omap3isp is probed */ +subsys_initcall(omap_iommu_init); static void __exit omap_iommu_exit(void) { diff --git a/arch/arm/mach-omap2/omap4-common.c b/arch/arm/mach-omap2/omap4-common.c index 40a8fbc07e4b..70de277f5c15 100644 --- a/arch/arm/mach-omap2/omap4-common.c +++ b/arch/arm/mach-omap2/omap4-common.c @@ -24,12 +24,14 @@ #include #include +#include #include #include #include "common.h" #include "omap4-sar-layout.h" +#include #ifdef CONFIG_CACHE_L2X0 static void __iomem *l2cache_base; @@ -43,6 +45,9 @@ static void __iomem *sar_ram_base; void __iomem *dram_sync, *sram_sync; +static phys_addr_t paddr; +static u32 size; + void omap_bus_sync(void) { if (dram_sync && sram_sync) { @@ -51,19 +56,22 @@ void omap_bus_sync(void) isb(); } } +EXPORT_SYMBOL(omap_bus_sync); -static int __init omap_barriers_init(void) +/* Steal one page physical memory for barrier implementation */ +int __init omap_barrier_reserve_memblock(void) { - struct map_desc dram_io_desc[1]; - phys_addr_t paddr; - u32 size; - - if (!cpu_is_omap44xx()) - return -ENODEV; size = ALIGN(PAGE_SIZE, SZ_1M); paddr = arm_memblock_steal(size, SZ_1M); + return 0; +} + +void __init omap_barriers_init(void) +{ + struct map_desc dram_io_desc[1]; + dram_io_desc[0].virtual = OMAP4_DRAM_BARRIER_VA; dram_io_desc[0].pfn = __phys_to_pfn(paddr); dram_io_desc[0].length = size; @@ -75,9 +83,10 @@ static int __init omap_barriers_init(void) pr_info("OMAP4: Map 0x%08llx to 0x%08lx for dram barrier\n", (long long) paddr, dram_io_desc[0].virtual); - return 0; } -core_initcall(omap_barriers_init); +#else +void __init omap_barriers_init(void) +{} #endif void __init gic_init_irq(void) diff --git a/arch/arm/mach-omap2/pm.c b/arch/arm/mach-omap2/pm.c index 1881fe915149..5a65dd04aa38 100644 --- a/arch/arm/mach-omap2/pm.c +++ b/arch/arm/mach-omap2/pm.c @@ -174,14 +174,17 @@ static int __init omap2_set_init_voltage(char *vdd_name, char *clk_name, freq = clk->rate; clk_put(clk); + rcu_read_lock(); opp = opp_find_freq_ceil(dev, &freq); if (IS_ERR(opp)) { + rcu_read_unlock(); pr_err("%s: unable to find boot up OPP for vdd_%s\n", __func__, vdd_name); goto exit; } bootup_volt = opp_get_voltage(opp); + rcu_read_unlock(); if (!bootup_volt) { pr_err("%s: unable to find voltage corresponding " "to the bootup OPP for vdd_%s\n", __func__, vdd_name); diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c index 10b20c652e5d..4b57757bf9d1 100644 --- a/arch/arm/mach-omap2/twl-common.c +++ b/arch/arm/mach-omap2/twl-common.c @@ -270,7 +270,6 @@ static struct regulator_init_data omap4_vusb_idata = { .constraints = { .min_uV = 3300000, .max_uV = 3300000, - .apply_uV = true, .valid_modes_mask = REGULATOR_MODE_NORMAL | REGULATOR_MODE_STANDBY, .valid_ops_mask = REGULATOR_CHANGE_MODE diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c index 771dc781b746..f51348dafafd 100644 --- a/arch/arm/mach-omap2/usb-host.c +++ b/arch/arm/mach-omap2/usb-host.c @@ -486,7 +486,7 @@ static void setup_4430ohci_io_mux(const enum usbhs_omap_port_mode *port_mode) void __init usbhs_init(const struct usbhs_omap_board_data *pdata) { struct omap_hwmod *oh[2]; - struct omap_device *od; + struct platform_device *pdev; int bus_id = -1; int i; @@ -522,11 +522,11 @@ void __init usbhs_init(const struct usbhs_omap_board_data *pdata) return; } - od = omap_device_build_ss(OMAP_USBHS_DEVICE, bus_id, oh, 2, + pdev = omap_device_build_ss(OMAP_USBHS_DEVICE, bus_id, oh, 2, (void *)&usbhs_data, sizeof(usbhs_data), omap_uhhtll_latency, ARRAY_SIZE(omap_uhhtll_latency), false); - if (IS_ERR(od)) { + if (IS_ERR(pdev)) { pr_err("Could not build hwmod devices %s,%s\n", USBHS_UHH_HWMODNAME, USBHS_TLL_HWMODNAME); return; diff --git a/arch/arm/mach-omap2/voltagedomains3xxx_data.c b/arch/arm/mach-omap2/voltagedomains3xxx_data.c index c005e2f5e383..57db2038b23c 100644 --- a/arch/arm/mach-omap2/voltagedomains3xxx_data.c +++ b/arch/arm/mach-omap2/voltagedomains3xxx_data.c @@ -108,6 +108,7 @@ void __init omap3xxx_voltagedomains_init(void) * XXX Will depend on the process, validation, and binning * for the currently-running IC */ +#ifdef CONFIG_PM_OPP if (cpu_is_omap3630()) { omap3_voltdm_mpu.volt_data = omap36xx_vddmpu_volt_data; omap3_voltdm_core.volt_data = omap36xx_vddcore_volt_data; @@ -115,6 +116,7 @@ void __init omap3xxx_voltagedomains_init(void) omap3_voltdm_mpu.volt_data = omap34xx_vddmpu_volt_data; omap3_voltdm_core.volt_data = omap34xx_vddcore_volt_data; } +#endif if (cpu_is_omap3517() || cpu_is_omap3505()) voltdms = voltagedomains_am35xx; diff --git a/arch/arm/mach-omap2/voltagedomains44xx_data.c b/arch/arm/mach-omap2/voltagedomains44xx_data.c index 4e11d022595d..c3115f6853d4 100644 --- a/arch/arm/mach-omap2/voltagedomains44xx_data.c +++ b/arch/arm/mach-omap2/voltagedomains44xx_data.c @@ -100,9 +100,11 @@ void __init omap44xx_voltagedomains_init(void) * XXX Will depend on the process, validation, and binning * for the currently-running IC */ +#ifdef CONFIG_PM_OPP omap4_voltdm_mpu.volt_data = omap44xx_vdd_mpu_volt_data; omap4_voltdm_iva.volt_data = omap44xx_vdd_iva_volt_data; omap4_voltdm_core.volt_data = omap44xx_vdd_core_volt_data; +#endif for (i = 0; voltdm = voltagedomains_omap4[i], voltdm; i++) voltdm->sys_clk.name = sys_clk_name; diff --git a/arch/arm/mach-pxa/generic.h b/arch/arm/mach-pxa/generic.h index 0d729e6619df..42d5cca66257 100644 --- a/arch/arm/mach-pxa/generic.h +++ b/arch/arm/mach-pxa/generic.h @@ -49,7 +49,6 @@ extern unsigned pxa3xx_get_clk_frequency_khz(int); #endif extern struct syscore_ops pxa_irq_syscore_ops; -extern struct syscore_ops pxa_gpio_syscore_ops; extern struct syscore_ops pxa2xx_mfp_syscore_ops; extern struct syscore_ops pxa3xx_mfp_syscore_ops; diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c index fb9b62dcf4ca..208eef1c0485 100644 --- a/arch/arm/mach-pxa/hx4700.c +++ b/arch/arm/mach-pxa/hx4700.c @@ -45,6 +45,7 @@ #include #include +#include #include