[ Upstream commit 02a1b175b0 ]
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the iph field from the state structure, which is not
properly initialized. Instead, add a new field to make the "do we want
to set DF" be the state bit and move the code to set the DF flag from
ip_frag_next().
Joint work with Pablo and Linus.
Fixes: 19c3401a91 ("net: ipv4: place control buffer handling away from fragmentation iterators")
Reported-by: Patrick Schönthaler <patrick@notvads.ovh>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable setting skb->mark for UDP and RAW sockets using cmsg.
This is analogous to existing support for TOS, TTL, txtime, etc.
Packet sockets already support this as of commit c7d39e3263
("packet: support per-packet fwmark for af_packet sendmsg").
Similar to other fields, implement by
1. initialize the sockcm_cookie.mark from socket option sk_mark
2. optionally overwrite this in ip_cmsg_send/ip6_datagram_send_ctl
3. initialize inet_cork.mark from sockcm_cookie.mark
4. initialize each (usually just one) skb->mark from inet_cork.mark
Step 1 is handled in one location for most protocols by ipcm_init_sk
as of commit 351782067b ("ipv4: ipcm_cookie initializers").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we want to set a EDT time for the skb we want to send
via ip_send_unicast_reply(), we have to pass a new parameter
and initialize ipc.sockc.transmit_time with it.
This fixes the EDT time for ACK/RST packets sent on behalf of
a TIME_WAIT socket.
Fixes: a842fe1425 ("tcp: add optional per socket transmit delay")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exposes a new API to refragment a skbuff. This allows you to
split either a linear skbuff or to force the refragmentation of an
existing fraglist using a different mtu. The API consists of:
* ip_frag_init(), that initializes the internal state of the transformer.
* ip_frag_next(), that allows you to fetch the next fragment. This function
internally allocates the skbuff that represents the fragment, it pushes
the IPv4 header, and it also copies the payload for each fragment.
The ip_frag_state object stores the internal state of the splitter.
This code has been extracted from ip_do_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the skbuff fraglist splitter. This API provides an
iterator to transform the fraglist into single skbuff objects, it
consists of:
* ip_fraglist_init(), that initializes the internal state of the
fraglist splitter.
* ip_fraglist_prepare(), that restores the IPv4 header on the
fragments.
* ip_fraglist_next(), that retrieves the fragment from the fraglist and
it updates the internal state of the splitter to point to the next
fragment skbuff in the fraglist.
The ip_fraglist_iter object stores the internal state of the iterator.
This code has been extracted from ip_do_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration check to accept source route IP options should be made on
the incoming netdevice when the skb->dev is an l3mdev master. The route
lookup for the source route next hop also needs the incoming netdev.
v2->v3:
- Simplify by passing the original netdevice down the stack (per David
Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_trie implementation calls synchronize_rcu when a certain amount of
pages are dirty from freed entries. The number of pages was determined
experimentally in 2009 (commit c3059477fc).
At the current setting, synchronize_rcu is called often -- 51 times in a
second in one test with an average of an 8 msec delay adding a fib entry.
The total impact is a lot of slow down modifying the fib. This is seen
in the output of 'time' - the difference between real time and sys+user.
For example, using 720,022 single path routes and 'ip -batch'[1]:
$ time ./ip -batch ipv4/routes-1-hops
real 0m14.214s
user 0m2.513s
sys 0m6.783s
So roughly 35% of the actual time to install the routes is from the ip
command getting scheduled out, most notably due to synchronize_rcu (this
is observed using 'perf sched timehist').
This patch makes the amount of dirty memory configurable between 64k where
the synchronize_rcu is called often (small, low end systems that are memory
sensitive) to 64M where synchronize_rcu is called rarely during a large
FIB change (for high end systems with lots of memory). The default is 512kB
which corresponds to the current setting of 128 pages with a 4kB page size.
As an example, at 16MB the worst interval shows 4 calls to synchronize_rcu
in a second blocking for up to 30 msec in a single instance, and a total
of almost 100 msec across the 4 calls in the second. The trade off is
allowing FIB entries to consume more memory in a given time window but
but with much better fib insertion rates (~30% increase in prefixes/sec).
With this patch and net.ipv4.fib_sync_mem set to 16MB, the same batch
file runs in:
$ time ./ip -batch ipv4/routes-1-hops
real 0m9.692s
user 0m2.491s
sys 0m6.769s
So the dead time is reduced to about 1/2 second or <5% of the real time.
[1] 'ip' modified to not request ACK messages which improves route
insertion times by about 20%
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384a3 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract IP options in cipso_v4_error and use __icmp_send.
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can re-use it at the UDP level in a later patch
rfc v3 -> v1
- add the helper declaration into the ip header
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack argument to ip_fib_metrics_init and add messages for invalid
metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
for ipv4 and ipv6 to a common helper.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv4 and ipv6 both use refcounted metrics if FIB entries have metrics set.
Move the common initialization code to a helper and use for both protocols.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the refcounting and potential free of dst metrics associated
with a fib entry to a helper and use it in both ipv4 and ipv6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate initialization of ipv4 and ipv6 metrics when fib entries
are created into a single helper, ip_fib_metrics_init, that handles
the call to ip_metrics_convert.
If no metrics are defined for the fib entry, then the metrics is set
to dst_default_metrics.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_shinfo(skb)->tx_flags is derived from sk->sk_tsflags, possibly
after modification by __sock_cmsg_send, by calling sock_tx_timestamp.
The IPv4 and IPv6 paths do this conversion differently. In IPv4, the
individual protocols that support tx timestamps call this function
and store the result in ipc.tx_flags. In IPv6, sock_tx_timestamp is
called in __ip6_append_data.
There is no need to store both tx_flags and ts_flags in the cookie
as one is derived from the other. Convert when setting up the cork
and remove the redundant field. This is similar to IPv6, only have
the conversion happen only once per datagram, in ip(6)_setup_cork.
Also change __ip6_append_data to match __ip_append_data. Only update
tskey if timestamping is enabled with OPT_ID. The SOCK_.. test is
redundant: only valid protocols can have non-zero cork->tx_flags.
After this change the IPv4 and IPv6 logic is the same.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba199 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also involved adding a way to run a netfilter hook over a list of packets.
Rather than attempting to make netfilter know about lists (which would be
a major project in itself) we just let it call the regular okfn (in this
case ip_rcv_finish()) for any packets it steals, and have it give us back
a list of packets it's synchronously accepted (which normally NF_HOOK
would automatically call okfn() on, but we want to be able to potentially
pass the list to a listified version of okfn().)
The netfilter hooks themselves are indirect calls that still happen per-
packet (see nf_hook_entry_hookfn()), but again, changing that can be left
for future work.
There is potential for out-of-order receives if the netfilter hook ends up
synchronously stealing packets, as they will be processed before any
accepts earlier in the list. However, it was already possible for an
asynchronous accept to cause out-of-order receives, so presumably this is
considered OK.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces __ip_queue_xmit(), through which the callers
can pass tos param into it without having to set inet->tos. For
ipv6, ip6_xmit() already allows passing tclass parameter.
It's needed when some transport protocol doesn't use inet->tos,
like sctp's per transport dscp, which will be added in next patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a followup to fib rules sport, dport and ipproto
match support. Only supports tcp, udp and icmp for ipproto.
Used by fib rule self tests.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support generic segmentation offload for udp datagrams. Callers can
concatenate and send at once the payload of multiple datagrams with
the same destination.
To set segment size, the caller sets socket option UDP_SEGMENT to the
length of each discrete payload. This value must be smaller than or
equal to the relevant MTU.
A follow-up patch adds cmsg UDP_SEGMENT to specify segment size on a
per send call basis.
Total byte length may then exceed MTU. If not an exact multiple of
segment size, the last segment will be shorter.
The implementation adds a gso_size field to the udp socket, ip(v6)
cmsg cookie and inet_cork structure to be able to set the value at
setsockopt or cmsg time and to work with both lockless and corked
paths.
Initial benchmark numbers show UDP GSO about as expensive as TCP GSO.
tcp tso
3197 MB/s 54232 msg/s 54232 calls/s
6,457,754,262 cycles
tcp gso
1765 MB/s 29939 msg/s 29939 calls/s
11,203,021,806 cycles
tcp without tso/gso *
739 MB/s 12548 msg/s 12548 calls/s
11,205,483,630 cycles
udp
876 MB/s 14873 msg/s 624666 calls/s
11,205,777,429 cycles
udp gso
2139 MB/s 36282 msg/s 36282 calls/s
11,204,374,561 cycles
[*] after reverting commit 0a6b2a1dc2
("tcp: switch to GSO being always on")
Measured total system cycles ('-a') for one core while pinning both
the network receive path and benchmark process to that core:
perf stat -a -C 12 -e cycles \
./udpgso_bench_tx -C 12 -4 -D "$DST" -l 4
Note the reduction in calls/s with GSO. Bytes per syscall drops
increases from 1470 to 61818.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP segmentation offload needs access to inet_cork in the udp layer.
Pass the struct to ip(6)_make_skb instead of allocating it on the
stack in that function itself.
This patch is a noop otherwise.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move logic of fib_convert_metrics into ip_metrics_convert. This allows
the code that converts netlink attributes into metrics struct to be
re-used in a later patch by IPv6.
This is mostly a code move with the following changes to variable names:
- fi->fib_net becomes net
- fc_mx and fc_mx_len are passed as inputs pulled from fib_config
- metrics array is passed as an input from fi->fib_metrics->metrics
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove sum_frag_mem_limit(), ip_frag_mem() & ip6_frag_mem()
Also since we use rhashtable we can bring back the number of fragments
in "grep FRAG /proc/net/sockstat /proc/net/sockstat6" that was
removed in commit 434d305405 ("inet: frag: don't account number
of fragment queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is optimization, which makes ip_call_ra_chain()
iterate less sockets to find the sockets it's looking for.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to the rework of PMTU information storage in commit
2c8cec5c10 ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.
Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.
This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().
One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.
Fixes: 2c8cec5c10 ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ran simple script to find/remove trailing whitespace and blank lines
at EOF because that kind of stuff git whines about and editors leave
behind.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 stack reacts to changes to small MTU, by disabling itself under
RTNL.
But there is a window where threads not using RTNL can see a wrong
device mtu. This can lead to surprises, in igmp code where it is
assumed the mtu is suitable.
Fix this by reading device mtu once and checking IPv4 minimal MTU.
This patch adds missing IPV4_MIN_MTU define, to not abuse
ETH_MIN_MTU anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the udp[46]_portaddr_hash()
to net/ip[v6].h. The function name is renamed to
ipv[46]_portaddr_hash().
It will be used by a later patch which adds a second listener
hashtable hashed by the address and port.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on yet another syzkaller report, I found
that our IP_MAX_MTU enforcements were not properly done.
gcc seems to reload dev->mtu for min(dev->mtu, IP_MAX_MTU), and
final result can be bigger than IP_MAX_MTU :/
This is a problem because device mtu can be changed on other cpus or
threads.
While this patch does not fix the issue I am working on, it is
probably worth addressing it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to udp socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Early demux lookups are handled in the next patch as part of INET_MATCH
changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ip_options_echo() uses the current network namespace, and
currently retrives it via skb->dst->dev.
This commit adds an explicit 'net' argument to __ip_options_echo()
and update all the call sites to provide it, usually via a simpler
sock_net().
After this change, __ip_options_echo() no more needs to access
skb->dst and we can drop a couple of hack to preserve such
info in the rx path.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Don't get the metric RTAX_ADVMSS of dst.
There are two reasons.
1) Its caller dst_metric_advmss has already invoke dst_metric_advmss
before invoke default_advmss.
2) The ipv4_default_advmss is used to get the default mss, it should
not try to get the metric like ip6_default_advmss.
2. Use sizeof(tcphdr)+sizeof(iphdr) instead of literal 40.
3. Define one new macro IPV4_MAX_PMTU instead of 65535 according to
RFC 2675, section 5.1.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add net.ipv4.ip_unprivileged_port_start, which is a per namespace sysctl
that denotes the first unprivileged inet port in the namespace. To
disable all privileged ports set this to zero. It also checks for
overlap with the local port range. The privileged and local range may
not overlap.
The use case for this change is to allow containerized processes to bind
to priviliged ports, but prevent them from ever being allowed to modify
their container's network configuration. The latter is accomplished by
ensuring that the network namespace is not a child of the user
namespace. This modification was needed to allow the container manager
to disable a namespace's priviliged port restrictions without exposing
control of the network namespace to processes in the user namespace.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it even after orphaining the skbuff.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some configurations (e.g. geneve interface with default
MTU of 1500 over an ethernet interface with 1500 MTU) result
in the transmission of packets that exceed the configured MTU.
While this should be considered to be a "bad" configuration,
it is still allowed and should not result in the sending
of packets that exceed the configured MTU.
Fix by dropping the assumption in ip_finish_output_gso() that
locally originated gso packets will never need fragmentation.
Basic testing using iperf (observing CPU usage and bandwidth)
have shown no measurable performance impact for traffic not
requiring fragmentation.
Fixes: c7ba65d7b6 ("net: ip: push gso skb forwarding handling down the stack")
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
First bug was added in commit ad6f939ab1 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6 ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, socket lookups for l3mdev (vrf) use cases can match a socket
that is bound to a port but not a device (ie., a global socket). If the
sysctl tcp_l3mdev_accept is not set this leads to ack packets going out
based on the main table even though the packet came in from an L3 domain.
The end result is that the connection does not establish creating
confusion for users since the service is running and a socket shows in
ss output. Fix by requiring an exact dif to sk_bound_dev_if match if the
skb came through an interface enslaved to an l3mdev device and the
tcp_l3mdev_accept is not set.
skb's through an l3mdev interface are marked by setting a flag in
inet{6}_skb_parm. The IPv6 variant is already set; this patch adds the
flag for IPv4. Using an skb flag avoids a device lookup on the dif. The
flag is set in the VRF driver using the IP{6}CB macros. For IPv4, the
inet_skb_parm struct is moved in the cb per commit 971f10eca1, so the
match function in the TCP stack needs to use TCP_SKB_CB. For IPv6, the
move is done after the socket lookup, so IP6CB is used.
The flags field in inet_skb_parm struct needs to be increased to add
another flag. There is currently a 1-byte hole following the flags,
so it can be expanded to u16 without increasing the size of the struct.
Fixes: 193125dbd8 ("net: Introduce VRF device driver")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to introduce the generic interfaces for snmp_get_cpu_field{,64}.
It exchanges the two for-loops for collecting the percpu statistics data.
This can aggregate the data by going through all the items of each cpu
sequentially.
Signed-off-by: Jia He <hejianet@gmail.com>
Suggested-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maciej Żenczykowski