Feiyang FY07024DI26A30-D MIPI_DSI panel is desiged to attach with
DSI connector on pine64 boards, enable the same for pine64 sopine.
DSI panel connected via board DSI port with,
- DC1SW as AVDD supply
- DLDO2 as DVDD supply
- DLDO1 as VCC-DSI supply
- PD24 gpio for reset pin
- PH10 gpio for backlight enable pin
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Add MIPI DSI pipeline for Allwinner A64.
- dsi node, with A64 compatible since it doesn't support
DSI_SCLK gating unlike A33
- dphy node, with A64 compatible with A33 fallback since
DPHY on A64 and A33 is similar
- finally, attach the dsi_in to tcon0 for complete MIPI DSI
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Add MIPI DSI pipeline for Allwinner A64.
- dsi node, with A64 compatible since it doesn't support
DSI_SCLK gating unlike A33
- dphy node, with A64 compatible with A33 fallback since
DPHY on A64 and A33 is similar
- finally, attach the dsi_in to tcon0 for complete MIPI DSI
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Merlijn Wajer <merlijn@wizzup.org>
Message-Id: <20191025175625.8011-7-jagan@amarulasolutions.com>
Pinebook has an ANX6345 bridge connected to the RGB666 LCD output and
eDP panel input. The bridge is controlled via I2C that's connected to
R_I2C bus.
There're pinebooks with 3 different panels in the wild, all 3 with
different timings. Add all the compatibles to panel node and hope that
we can get correct timings from EDID. If reading EDID fails it's up to
firmware to fixup compatible string.
Enable all this hardware in device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
SoPine has optional RTL8723BS WiFi + BT module, BT is connected to UART1
and uses PL4 as BT reset, PL5 as device wake GPIO, PL6 as host wake GPIO
the I2C controlling signals are connected to R_I2C bus.
Enable it in the device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Pine64 has optional RTL8723BS WiFi + BT module, BT is connected to UART1
and uses PL4 as BT reset, PL5 as device wake GPIO, PL6 as host wake GPIO
the I2C controlling signals are connected to R_I2C bus.
Enable it in the device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Pinebook has an RTL8723CS WiFi + BT chip, BT is connected to UART1
and uses PL4 as BT reset, PL5 as device wake GPIO, PL6 as host wake GPIO
the I2C controlling signals are connected to R_I2C bus.
Enable it in the device tree.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Some Pine64+ boards have a broken RTL8211E PHY, which cannot work
reliably in 1000Base-T mode with default configuration.
A solution is passed to Pine64, which is said to be disabling the
internal RX delay of the PHY.
Enable the hack by set the PHY mode to RGMII-TXID.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The Wi-Fi modules of Pine64 is powered via DLDO4 and ELDO1 (the latter
one provides I/O voltage).
Add device node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
- Ensure PAN is re-enabled following user fault in uaccess routines
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl3WdTEQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNE43B/9ow5C7aV1Jmb9dk3zfkDkVuviCkv9STpNW
YosKSAHwGvsfmBd/f+kd/ipqnt/fBLbXHqRderbayDW7xundCP8Qgl51N2RwJ92O
si3rPHW62xjbv0U3XqY9h74wH4jfox3KAT8c5EBcLuZtmV3gTb1txWDQ0PfQZMpN
0cmfTRPHB7LKJ/hupEyq6iVPYx+mV1ajenW1uzBOQhu+c8jC5Uf9kDn/D93rCYCg
7NL88odhP0Oyt6HDcR5LB+nl7fz+q0jXzxyF8qHDWNitV4aovU9rLMpDpn4YVvYd
DcFEyGdwYSxExLFrBuvmevZ7+2biT3qWQcPuNQGCcqWQSu38ULFK
=r7nI
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Ensure PAN is re-enabled following user fault in uaccess routines.
After I thought we were done for 5.4, we had a report this week of a
nasty issue that has been shown to leak data between different user
address spaces thanks to corruption of entries in the TLB. In
hindsight, we should have spotted this in review when the PAN code was
merged back in v4.3, but hindsight is 20/20 and I'm trying not to beat
myself up too much about it despite being fairly miserable.
Anyway, the fix is "obvious" but the actual failure is more more
subtle, and is described in the commit message. I've included a fairly
mechanical follow-up patch here as well, which moves this checking out
into the C wrappers which is what we do for {get,put}_user() already
and allows us to remove these bloody assembly macros entirely. The
patches have passed kernelci [1] [2] [3] and CKI [4] tests over night,
as well as some targetted testing [5] for this particular issue.
The first patch is tagged for stable and should be applied to 4.14,
4.19 and 5.3. I have separate backports for 4.4 and 4.9, which I'll
send out once this has landed in your tree (although the original
patch applies cleanly, it won't build for those two trees).
Thanks to Pavel Tatashin for reporting this and Mark Rutland for
helping to diagnose the issue and review/test the solution"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: uaccess: Remove uaccess_*_not_uao asm macros
arm64: uaccess: Ensure PAN is re-enabled after unhandled uaccess fault
It is safer and simpler to drop the uaccess assembly macros in favour of
inline C functions. Although this bloats the Image size slightly, it
aligns our user copy routines with '{get,put}_user()' and generally
makes the code a lot easier to reason about.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: tweaked commit message and changed temporary variable names]
Signed-off-by: Will Deacon <will@kernel.org>
A number of our uaccess routines ('__arch_clear_user()' and
'__arch_copy_{in,from,to}_user()') fail to re-enable PAN if they
encounter an unhandled fault whilst accessing userspace.
For CPUs implementing both hardware PAN and UAO, this bug has no effect
when both extensions are in use by the kernel.
For CPUs implementing hardware PAN but not UAO, this means that a kernel
using hardware PAN may execute portions of code with PAN inadvertently
disabled, opening us up to potential security vulnerabilities that rely
on userspace access from within the kernel which would usually be
prevented by this mechanism. In other words, parts of the kernel run the
same way as they would on a CPU without PAN implemented/emulated at all.
For CPUs not implementing hardware PAN and instead relying on software
emulation via 'CONFIG_ARM64_SW_TTBR0_PAN=y', the impact is unfortunately
much worse. Calling 'schedule()' with software PAN disabled means that
the next task will execute in the kernel using the page-table and ASID
of the previous process even after 'switch_mm()', since the actual
hardware switch is deferred until return to userspace. At this point, or
if there is a intermediate call to 'uaccess_enable()', the page-table
and ASID of the new process are installed. Sadly, due to the changes
introduced by KPTI, this is not an atomic operation and there is a very
small window (two instructions) where the CPU is configured with the
page-table of the old task and the ASID of the new task; a speculative
access in this state is disastrous because it would corrupt the TLB
entries for the new task with mappings from the previous address space.
As Pavel explains:
| I was able to reproduce memory corruption problem on Broadcom's SoC
| ARMv8-A like this:
|
| Enable software perf-events with PERF_SAMPLE_CALLCHAIN so userland's
| stack is accessed and copied.
|
| The test program performed the following on every CPU and forking
| many processes:
|
| unsigned long *map = mmap(NULL, PAGE_SIZE, PROT_READ|PROT_WRITE,
| MAP_SHARED | MAP_ANONYMOUS, -1, 0);
| map[0] = getpid();
| sched_yield();
| if (map[0] != getpid()) {
| fprintf(stderr, "Corruption detected!");
| }
| munmap(map, PAGE_SIZE);
|
| From time to time I was getting map[0] to contain pid for a
| different process.
Ensure that PAN is re-enabled when returning after an unhandled user
fault from our uaccess routines.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: 338d4f49d6 ("arm64: kernel: Add support for Privileged Access Never")
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: rewrote commit message]
Signed-off-by: Will Deacon <will@kernel.org>
Pull x86 fixes from Ingo Molnar:
"Two fixes: disable unreliable HPET on Intel Coffe Lake platforms, and
fix a lockdep splat in the resctrl code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Fix potential lockdep warning
x86/quirks: Disable HPET on Intel Coffe Lake platforms
MAINTAINERS update for Broadcom MIPS systems.
-----BEGIN PGP SIGNATURE-----
iIwEABYIADQWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXc4wwBYccGF1bGJ1cnRv
bkBrZXJuZWwub3JnAAoJED6nn6y1dQDdgA4BAPUIK91zzLqrG5krdu5Df/UDM3EN
XlhhDTX8tT7QHvufAP9Uyn9FkbCIPmupBp+6s7Q6OvHGyG8TYRxTehyMtdLiBA==
=McJE
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_5.4_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A fix and simplification for SGI IP27 exception handlers, and a small
MAINTAINERS update for Broadcom MIPS systems"
* tag 'mips_fixes_5.4_4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MAINTAINERS: Remove Kevin as maintainer of BMIPS generic platforms
MIPS: SGI-IP27: fix exception handler replication
* Two updates to the IFU erratum
* selftests build fix
* Brown paper bag fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdzm9YAAoJEL/70l94x66DUWAIAKODbb0j7IB9RHD3lOJI9evz
m/+ajirYug2/vv78IkCo02sVssuHqUvqes60AlUGz7ZzGzVdwbSJ9dsu+e9ylq7M
ZJIySe1R31R9qKbjoszKmL8/Dc8oe4pCHvwPsVDLNHFMmgb7nbaBrQ7SnPK8iwas
N2ljMiq8gTRYmEmF7VOw2SZqm8BebjhxjfN8RVTOvDDkMozD15djw7mQ1BH0aISs
rFt8NH8qXhgbdHXMyQUnQrNySMeH5igrrPLFESOshjIcVq67gUKW6pMdDc+uIVM7
9SLqa8mY4PfuHaYAaljZ7PKs3EkcUt5Si0arP7gF+Y0WIObALlUMr2tNDeClBmY=
=VE3v
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull more KVM fixes from Paolo Bonzini:
- fixes for CONFIG_KVM_COMPAT=n
- two updates to the IFU erratum
- selftests build fix
- brown paper bag fix
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Add a comment describing the /dev/kvm no_compat handling
KVM: x86/mmu: Take slots_lock when using kvm_mmu_zap_all_fast()
KVM: Forbid /dev/kvm being opened by a compat task when CONFIG_KVM_COMPAT=n
KVM: X86: Reset the three MSR list number variables to 0 in kvm_init_msr_list()
selftests: kvm: fix build with glibc >= 2.30
kvm: x86: disable shattered huge page recovery for PREEMPT_RT.
Acquire the per-VM slots_lock when zapping all shadow pages as part of
toggling nx_huge_pages. The fast zap algorithm relies on exclusivity
(via slots_lock) to identify obsolete vs. valid shadow pages, because it
uses a single bit for its generation number. Holding slots_lock also
obviates the need to acquire a read lock on the VM's srcu.
Failing to take slots_lock when toggling nx_huge_pages allows multiple
instances of kvm_mmu_zap_all_fast() to run concurrently, as the other
user, KVM_SET_USER_MEMORY_REGION, does not take the global kvm_lock.
(kvm_mmu_zap_all_fast() does take kvm->mmu_lock, but it can be
temporarily dropped by kvm_zap_obsolete_pages(), so it is not enough
to enforce exclusivity).
Concurrent fast zap instances causes obsolete shadow pages to be
incorrectly identified as valid due to the single bit generation number
wrapping, which results in stale shadow pages being left in KVM's MMU
and leads to all sorts of undesirable behavior.
The bug is easily confirmed by running with CONFIG_PROVE_LOCKING and
toggling nx_huge_pages via its module param.
Note, until commit 4ae5acbc4936 ("KVM: x86/mmu: Take slots_lock when
using kvm_mmu_zap_all_fast()", 2019-11-13) the fast zap algorithm used
an ulong-sized generation instead of relying on exclusivity for
correctness, but all callers except the recently added set_nx_huge_pages()
needed to hold slots_lock anyways. Therefore, this patch does not have
to be backported to stable kernels.
Given that toggling nx_huge_pages is by no means a fast path, force it
to conform to the current approach instead of reintroducing the previous
generation count.
Fixes: b8e8c8303f ("kvm: mmu: ITLB_MULTIHIT mitigation", but NOT FOR STABLE)
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 54b8ae66ae ("kbuild: change *FLAGS_<basetarget>.o to
take the path relative to $(obj)"), sparc allmodconfig fails to build
as follows:
CC arch/sparc/vdso/vdso32/vclock_gettime.o
unrecognized e_machine 18 arch/sparc/vdso/vdso32/vclock_gettime.o
arch/sparc/vdso/vdso32/vclock_gettime.o: failed
The cause of the breakage is that -pg flag not being dropped.
The vdso32 files are located in the vdso32/ subdirectory, but I missed
to update the Makefile.
I removed the meaningless CFLAGS_REMOVE_vdso-note.o since it is only
effective for C file.
vdso-note.o is compiled from assembly file:
arch/sparc/vdso/vdso-note.S
arch/sparc/vdso/vdso32/vdso-note.S
Fixes: 54b8ae66ae ("kbuild: change *FLAGS_<basetarget>.o to take the path relative to $(obj)")
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Anatoly Pugachev <matorola@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
When applying commit 7a5ee6edb4 ("KVM: X86: Fix initialization of MSR
lists"), it forgot to reset the three MSR lists number varialbes to 0
while removing the useless conditionals.
Fixes: 7a5ee6edb4 (KVM: X86: Fix initialization of MSR lists)
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a huge page is recovered (and becomes no executable) while another
thread is executing it, the resulting contention on mmu_lock can cause
latency spikes. Disabling recovery for PREEMPT_RT kernels fixes this
issue.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
rdtgroup_cpus_write() and mkdir_rdt_prepare() call
rdtgroup_kn_lock_live() -> kernfs_to_rdtgroup() to get 'rdtgrp', and
then call the rdt_last_cmd_{clear,puts,...}() functions which will check
if rdtgroup_mutex is held/requires its caller to hold rdtgroup_mutex.
But if 'rdtgrp' returned from kernfs_to_rdtgroup() is NULL,
rdtgroup_mutex is not held and calling rdt_last_cmd_{clear,puts,...}()
will result in a self-incurred, potential lockdep warning.
Remove the rdt_last_cmd_{clear,puts,...}() calls in these two paths.
Just returning error should be sufficient to report to the user that the
entry doesn't exist any more.
[ bp: Massage. ]
Fixes: 94457b36e8 ("x86/intel_rdt: Add diagnostics when writing the cpus file")
Fixes: cfd0f34e4c ("x86/intel_rdt: Add diagnostics when making directories")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Reviewed-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: pei.p.jia@intel.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1573079796-11713-1-git-send-email-xiaochen.shen@intel.com
VT-d posted interrupts, DAX/ZONE_DEVICE,
module unload/reload.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdyrEsAAoJEL/70l94x66DIOkH/Asqrh4o4pwfRHWE+9rnM6PI
j8oFi7Q4eRXJnP4zEMnMbb6xD/BfSH1tWEcPcYgIxD/t0DFx8F92/xsETAJ/Qc5n
CWpmnhMkJqERlV+GSRuBqnheMo0CEH1Ab1QZKhh5U3//pK3OtGY9WyydJHWcquTh
bGh2pnxwVZOtIIEmclUUfKjyR2Fu8hJLnQwzWgYZ27UK7J2pLmiiTX0vwQG359Iq
sDn9ND33pCBW5e/D2mzccRjOJEvzwrumewM1sRDsoAYLJzUjg9+xD83vZDa1d7R6
gajCDFWVJbPoLvUY+DgsZBwMMlogElimJMT/Zft3ERbCsYJbFvcmwp4JzyxDxQ4=
=J6KN
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Fix unwinding of KVM_CREATE_VM failure, VT-d posted interrupts,
DAX/ZONE_DEVICE, and module unload/reload"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: Do not treat ZONE_DEVICE pages as being reserved
KVM: VMX: Introduce pi_is_pir_empty() helper
KVM: VMX: Do not change PID.NDST when loading a blocked vCPU
KVM: VMX: Consider PID.PIR to determine if vCPU has pending interrupts
KVM: VMX: Fix comment to specify PID.ON instead of PIR.ON
KVM: X86: Fix initialization of MSR lists
KVM: fix placement of refcount initialization
KVM: Fix NULL-ptr deref after kvm_create_vm fails
Pull x86 TSX Async Abort and iTLB Multihit mitigations from Thomas Gleixner:
"The performance deterioration departement is not proud at all of
presenting the seventh installment of speculation mitigations and
hardware misfeature workarounds:
1) TSX Async Abort (TAA) - 'The Annoying Affair'
TAA is a hardware vulnerability that allows unprivileged
speculative access to data which is available in various CPU
internal buffers by using asynchronous aborts within an Intel TSX
transactional region.
The mitigation depends on a microcode update providing a new MSR
which allows to disable TSX in the CPU. CPUs which have no
microcode update can be mitigated by disabling TSX in the BIOS if
the BIOS provides a tunable.
Newer CPUs will have a bit set which indicates that the CPU is not
vulnerable, but the MSR to disable TSX will be available
nevertheless as it is an architected MSR. That means the kernel
provides the ability to disable TSX on the kernel command line,
which is useful as TSX is a truly useful mechanism to accelerate
side channel attacks of all sorts.
2) iITLB Multihit (NX) - 'No eXcuses'
iTLB Multihit is an erratum where some Intel processors may incur
a machine check error, possibly resulting in an unrecoverable CPU
lockup, when an instruction fetch hits multiple entries in the
instruction TLB. This can occur when the page size is changed
along with either the physical address or cache type. A malicious
guest running on a virtualized system can exploit this erratum to
perform a denial of service attack.
The workaround is that KVM marks huge pages in the extended page
tables as not executable (NX). If the guest attempts to execute in
such a page, the page is broken down into 4k pages which are
marked executable. The workaround comes with a mechanism to
recover these shattered huge pages over time.
Both issues come with full documentation in the hardware
vulnerabilities section of the Linux kernel user's and administrator's
guide.
Thanks to all patch authors and reviewers who had the extraordinary
priviledge to be exposed to this nuisance.
Special thanks to Borislav Petkov for polishing the final TAA patch
set and to Paolo Bonzini for shepherding the KVM iTLB workarounds and
providing also the backports to stable kernels for those!"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/taa: Fix printing of TAA_MSG_SMT on IBRS_ALL CPUs
Documentation: Add ITLB_MULTIHIT documentation
kvm: x86: mmu: Recovery of shattered NX large pages
kvm: Add helper function for creating VM worker threads
kvm: mmu: ITLB_MULTIHIT mitigation
cpu/speculation: Uninline and export CPU mitigations helpers
x86/cpu: Add Tremont to the cpu vulnerability whitelist
x86/bugs: Add ITLB_MULTIHIT bug infrastructure
x86/tsx: Add config options to set tsx=on|off|auto
x86/speculation/taa: Add documentation for TSX Async Abort
x86/tsx: Add "auto" option to the tsx= cmdline parameter
kvm/x86: Export MDS_NO=0 to guests when TSX is enabled
x86/speculation/taa: Add sysfs reporting for TSX Async Abort
x86/speculation/taa: Add mitigation for TSX Async Abort
x86/cpu: Add a "tsx=" cmdline option with TSX disabled by default
x86/cpu: Add a helper function x86_read_arch_cap_msr()
x86/msr: Add the IA32_TSX_CTRL MSR
Some Coffee Lake platforms have a skewed HPET timer once the SoCs entered
PC10, which in consequence marks TSC as unstable because HPET is used as
watchdog clocksource for TSC.
Harry Pan tried to work around it in the clocksource watchdog code [1]
thereby creating a circular dependency between HPET and TSC. This also
ignores the fact, that HPET is not only unsuitable as watchdog clocksource
on these systems, it becomes unusable in general.
Disable HPET on affected platforms.
Suggested-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203183
Link: https://lore.kernel.org/lkml/20190516090651.1396-1-harry.pan@intel.com/ [1]
Link: https://lkml.kernel.org/r/20191016103816.30650-1-kai.heng.feng@canonical.com
Explicitly exempt ZONE_DEVICE pages from kvm_is_reserved_pfn() and
instead manually handle ZONE_DEVICE on a case-by-case basis. For things
like page refcounts, KVM needs to treat ZONE_DEVICE pages like normal
pages, e.g. put pages grabbed via gup(). But for flows such as setting
A/D bits or shifting refcounts for transparent huge pages, KVM needs to
to avoid processing ZONE_DEVICE pages as the flows in question lack the
underlying machinery for proper handling of ZONE_DEVICE pages.
This fixes a hang reported by Adam Borowski[*] in dev_pagemap_cleanup()
when running a KVM guest backed with /dev/dax memory, as KVM straight up
doesn't put any references to ZONE_DEVICE pages acquired by gup().
Note, Dan Williams proposed an alternative solution of doing put_page()
on ZONE_DEVICE pages immediately after gup() in order to simplify the
auditing needed to ensure is_zone_device_page() is called if and only if
the backing device is pinned (via gup()). But that approach would break
kvm_vcpu_{un}map() as KVM requires the page to be pinned from map() 'til
unmap() when accessing guest memory, unlike KVM's secondary MMU, which
coordinates with mmu_notifier invalidations to avoid creating stale
page references, i.e. doesn't rely on pages being pinned.
[*] http://lkml.kernel.org/r/20190919115547.GA17963@angband.pl
Reported-by: Adam Borowski <kilobyte@angband.pl>
Analyzed-by: David Hildenbrand <david@redhat.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Fixes: 3565fce3a6 ("mm, x86: get_user_pages() for dax mappings")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Streamline the PID.PIR check and change its call sites to use
the newly added helper.
Suggested-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When vCPU enters block phase, pi_pre_block() inserts vCPU to a per pCPU
linked list of all vCPUs that are blocked on this pCPU. Afterwards, it
changes PID.NV to POSTED_INTR_WAKEUP_VECTOR which its handler
(wakeup_handler()) is responsible to kick (unblock) any vCPU on that
linked list that now has pending posted interrupts.
While vCPU is blocked (in kvm_vcpu_block()), it may be preempted which
will cause vmx_vcpu_pi_put() to set PID.SN. If later the vCPU will be
scheduled to run on a different pCPU, vmx_vcpu_pi_load() will clear
PID.SN but will also *overwrite PID.NDST to this different pCPU*.
Instead of keeping it with original pCPU which vCPU had entered block
phase on.
This results in an issue because when a posted interrupt is delivered, as
the wakeup_handler() will be executed and fail to find blocked vCPU on
its per pCPU linked list of all vCPUs that are blocked on this pCPU.
Which is due to the vCPU being placed on a *different* per pCPU
linked list i.e. the original pCPU in which it entered block phase.
The regression is introduced by commit c112b5f502 ("KVM: x86:
Recompute PID.ON when clearing PID.SN"). Therefore, partially revert
it and reintroduce the condition in vmx_vcpu_pi_load() responsible for
avoiding changing PID.NDST when loading a blocked vCPU.
Fixes: c112b5f502 ("KVM: x86: Recompute PID.ON when clearing PID.SN")
Tested-by: Nathan Ni <nathan.ni@oracle.com>
Co-developed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 17e433b543 ("KVM: Fix leak vCPU's VMCS value into other pCPU")
introduced vmx_dy_apicv_has_pending_interrupt() in order to determine
if a vCPU have a pending posted interrupt. This routine is used by
kvm_vcpu_on_spin() when searching for a a new runnable vCPU to schedule
on pCPU instead of a vCPU doing busy loop.
vmx_dy_apicv_has_pending_interrupt() determines if a
vCPU has a pending posted interrupt solely based on PID.ON. However,
when a vCPU is preempted, vmx_vcpu_pi_put() sets PID.SN which cause
raised posted interrupts to only set bit in PID.PIR without setting
PID.ON (and without sending notification vector), as depicted in VT-d
manual section 5.2.3 "Interrupt-Posting Hardware Operation".
Therefore, checking PID.ON is insufficient to determine if a vCPU has
pending posted interrupts and instead we should also check if there is
some bit set on PID.PIR if PID.SN=1.
Fixes: 17e433b543 ("KVM: Fix leak vCPU's VMCS value into other pCPU")
Reviewed-by: Jagannathan Raman <jag.raman@oracle.com>
Co-developed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Outstanding Notification (ON) bit is part of the Posted Interrupt
Descriptor (PID) as opposed to the Posted Interrupts Register (PIR).
The latter is a bitmap for pending vectors.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The three MSR lists(msrs_to_save[], emulated_msrs[] and
msr_based_features[]) are global arrays of kvm.ko, which are
adjusted (copy supported MSRs forward to override the unsupported MSRs)
when insmod kvm-{intel,amd}.ko, but it doesn't reset these three arrays
to their initial value when rmmod kvm-{intel,amd}.ko. Thus, at the next
installation, kvm-{intel,amd}.ko will do operations on the modified
arrays with some MSRs lost and some MSRs duplicated.
So define three constant arrays to hold the initial MSR lists and
initialize msrs_to_save[], emulated_msrs[] and msr_based_features[]
based on the constant arrays.
Cc: stable@vger.kernel.org
Reviewed-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
[Remove now useless conditionals. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for CAN
interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage scaling
issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem
-----BEGIN PGP SIGNATURE-----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=Ei7j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
CAN interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage
scaling issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: update Cavium ThunderX2 maintainers
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
reset: fix reset_control_ops kerneldoc comment
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
reset: fix reset_control_get_exclusive kerneldoc comment
reset: fix reset_control_lookup kerneldoc comment
reset: fix of_reset_control_get_count kerneldoc comment
reset: fix of_reset_simple_xlate kerneldoc comment
reset: Fix memory leak in reset_control_array_put()
Pull x86 fixes from Thomas Gleixner:
"A small set of fixes for x86:
- Make the tsc=reliable/nowatchdog command line parameter work again.
It was broken with the introduction of the early TSC clocksource.
- Prevent the evaluation of exception stacks before they are set up.
This causes a crash in dumpstack because the stack walk termination
gets screwed up.
- Prevent a NULL pointer dereference in the rescource control file
system.
- Avoid bogus warnings about APIC id mismatch related to the LDR
which can happen when the LDR is not in use and therefore not
initialized. Only evaluate that when the APIC is in logical
destination mode"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsc: Respect tsc command line paraemeter for clocksource_tsc_early
x86/dumpstack/64: Don't evaluate exception stacks before setup
x86/apic/32: Avoid bogus LDR warnings
x86/resctrl: Prevent NULL pointer dereference when reading mondata
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
- Fix pte_same() to avoid getting stuck on write fault
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl3FPbsQHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNOkjB/9sNekV5x5vtLSXLPXH7TEt2jsKPHKHoc5h
i9bnpZc8na50Sj9V4ugMs4mqa5qOw+m2sJEHXxVr5k/bNJv3gqEpWAlnb4bXgjDj
yukM9FQVBRNMdDFeP3Yjm9VuoWhId0L9OfqCq/N6xi2kN3Xp60Ms7drYQeweBdEa
dBj4x52o/lMo3h5JF0QmWKTD85Nz0f4GxX4gclBMqsg/VAQOMDho86mMsfecwgCA
y9WbJClsH3nBcV8bChx0oSGzM+lJBmP6OnlxKM9tyzTmhJJQw4FDUmHmlaFptMe4
DRqJnVi41tzv7p8As/aE4sY7rnWEKaitn0r7gCfei+ACJG0Ezmas
=3M1Z
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Fix pte_same() to avoid getting stuck on write fault.
This single arm64 fix is a revert of 747a70e60b ("arm64: Fix
copy-on-write referencing in HugeTLB"), not because that patch was
wrong, but because it was broken by aa57157be6 ("arm64: Ensure
VM_WRITE|VM_SHARED ptes are clean by default") which we merged in
-rc6.
We spotted the issue in Android (AOSP), where one of the JIT threads
gets stuck on a write fault during boot because the faulting pte is
marked as PTE_DIRTY | PTE_WRITE | PTE_RDONLY and the fault handler
decides that there's nothing to do thanks to pte_same() masking out
PTE_RDONLY.
Thanks to John Stultz for reporting this and testing this so quickly,
and to Steve Capper for confirming that the HugeTLB tests continue to
pass"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Do not mask out PTE_RDONLY in pte_same()
For new IBRS_ALL CPUs, the Enhanced IBRS check at the beginning of
cpu_bugs_smt_update() causes the function to return early, unintentionally
skipping the MDS and TAA logic.
This is not a problem for MDS, because there appears to be no overlap
between IBRS_ALL and MDS-affected CPUs. So the MDS mitigation would be
disabled and nothing would need to be done in this function anyway.
But for TAA, the TAA_MSG_SMT string will never get printed on Cascade
Lake and newer.
The check is superfluous anyway: when 'spectre_v2_enabled' is
SPECTRE_V2_IBRS_ENHANCED, 'spectre_v2_user' is always
SPECTRE_V2_USER_NONE, and so the 'spectre_v2_user' switch statement
handles it appropriately by doing nothing. So just remove the check.
Fixes: 1b42f01741 ("x86/speculation/taa: Add mitigation for TSX Async Abort")
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Following commit 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out
of set_pte_at()"), the PTE_RDONLY bit is no longer managed by
set_pte_at() but built into the PAGE_* attribute definitions.
Consequently, pte_same() must include this bit when checking two PTEs
for equality.
Remove the arm64-specific pte_same() function, practically reverting
commit 747a70e60b ("arm64: Fix copy-on-write referencing in HugeTLB")
Fixes: 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Highlights:
-----------
Fixes for STM32MP157:
-Fix CAN RAM mapping
-Change stmfx pinctrl definition for joystick and camera. Due to
stmfx pinctrl fix done in v5.4-rc cycle, camera and joystick were no
longer functional.
-----BEGIN PGP SIGNATURE-----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=Fv0m
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v5.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/fixes
STM32 DT fixes for v5.4, round 2
Highlights:
-----------
Fixes for STM32MP157:
-Fix CAN RAM mapping
-Change stmfx pinctrl definition for joystick and camera. Due to
stmfx pinctrl fix done in v5.4-rc cycle, camera and joystick were no
longer functional.
* tag 'stm32-dt-for-v5.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
Link: https://lore.kernel.org/r/d316b81f-a8d7-e9be-fe3c-73a242e7d941@st.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Pins used for joystick are all configured as input. "push-pull" is not a
valid setting for an input pin.
Fixes: a502b343eb ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
"push-pull" configuration is now fully handled by the gpiolib and the
STMFX pinctrl driver. There is no longer need to declare a pinctrl group
to only configure "push-pull" setting for the line. It is done directly by
the gpiolib.
Fixes: a502b343eb ("pinctrl: stmfx: update pinconf settings")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Split the 10Kbytes CAN message RAM to be able to use simultaneously
FDCAN1 and FDCAN2 instances.
First 5Kbytes are allocated to FDCAN1 and last 5Kbytes are used for
FDCAN2. To do so, set the offset to 0x1400 in mram-cfg for FDCAN2.
Fixes: d44d6e0213 ("ARM: dts: stm32: change CAN RAM mapping on stm32mp157c")
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Alistair Francis