Pull networking fixes from David Miller:
1) Validate tunnel options length in act_tunnel_key, from Xin Long.
2) Fix DMA sync bug in gve driver, from Adi Suresh.
3) TSO kills performance on some r8169 chips due to HW issues, disable
by default in that case, from Corinna Vinschen.
4) Fix clock disable mismatch in fec driver, from Chubong Yuan.
5) Fix interrupt status bits define in hns3 driver, from Huazhong Tan.
6) Fix workqueue deadlocks in qeth driver, from Julian Wiedmann.
7) Don't napi_disable() twice in r8152 driver, from Hayes Wang.
8) Fix SKB extension memory leak, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
r8152: avoid to call napi_disable twice
MAINTAINERS: Add myself as maintainer of virtio-vsock
udp: drop skb extensions before marking skb stateless
net: rtnetlink: prevent underflows in do_setvfinfo()
can: m_can_platform: remove unnecessary m_can_class_resume() call
can: m_can_platform: set net_device structure as driver data
hv_netvsc: Fix send_table offset in case of a host bug
hv_netvsc: Fix offset usage in netvsc_send_table()
net-ipv6: IPV6_TRANSPARENT - check NET_RAW prior to NET_ADMIN
sfc: Only cancel the PPS workqueue if it exists
nfc: port100: handle command failure cleanly
net-sysfs: fix netdev_queue_add_kobject() breakage
r8152: Re-order napi_disable in rtl8152_close
net: qca_spi: Move reset_count to struct qcaspi
net: qca_spi: fix receive buffer size check
net/ibmvnic: Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
Revert "net/ibmvnic: Fix EOI when running in XIVE mode"
net/mlxfw: Verify FSM error code translation doesn't exceed array size
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix auto group size calculation
...
Fix problems with switching cpufreq drivers on some x86 systems with
ACPI (and with changing the operation modes of the intel_pstate driver
on those systems) introduced by recent changes related to the
management of frequency limits in cpufreq.
-----BEGIN PGP SIGNATURE-----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=S23p
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management regression fix from Rafael Wysocki:
"Fix problems with switching cpufreq drivers on some x86 systems with
ACPI (and with changing the operation modes of the intel_pstate driver
on those systems) introduced by recent changes related to the
management of frequency limits in cpufreq"
* tag 'pm-5.4-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: QoS: Invalidate frequency QoS requests after removal
pidfd_poll() is defined as returning 'unsigned int' but the
.poll method is declared as returning '__poll_t', a bitwise type.
Fix this by using the proper return type and using the EPOLL
constants instead of the POLL ones, as required for __poll_t.
Fixes: b53b0b9d9a ("pidfd: add polling support")
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: stable@vger.kernel.org # 5.3
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191120003320.31138-1-luc.vanoostenryck@gmail.com
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Switching cpufreq drivers (or switching operation modes of the
intel_pstate driver from "active" to "passive" and vice versa)
does not work on some x86 systems with ACPI after commit
3000ce3c52 ("cpufreq: Use per-policy frequency QoS"), because
the ACPI _PPC and thermal code uses the same frequency QoS request
object for a given CPU every time a cpufreq driver is registered
and freq_qos_remove_request() does not invalidate the request after
removing it from its QoS list, so freq_qos_add_request() complains
and fails when that request is passed to it again.
Fix the issue by modifying freq_qos_remove_request() to clear the qos
and type fields of the frequency request pointed to by its argument
after removing it from its QoS list so as to invalidate it.
Fixes: 3000ce3c52 ("cpufreq: Use per-policy frequency QoS")
Reported-and-tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-15
The following pull-request contains BPF updates for your *net* tree.
We've added 1 non-merge commits during the last 9 day(s) which contain
a total of 1 file changed, 3 insertions(+), 1 deletion(-).
The main changes are:
1) Fix a missing unlock of bpf_devs_lock in bpf_offload_dev_create()'s
error path, from Dan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"Misc fixes: a handful of AUX event handling related fixes, a Sparse
fix and two ABI fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix missing static inline on perf_cgroup_switch()
perf/core: Consistently fail fork on allocation failures
perf/aux: Disallow aux_output for kernel events
perf/core: Reattach a misplaced comment
perf/aux: Fix the aux_output group inheritance fix
perf/core: Disallow uncore-cgroup events
Pull misc vfs fixes from Al Viro:
"Assorted fixes all over the place; some of that is -stable fodder,
some regressions from the last window"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ecryptfs_lookup_interpose(): lower_dentry->d_parent is not stable either
ecryptfs_lookup_interpose(): lower_dentry->d_inode is not stable
ecryptfs: fix unlink and rmdir in face of underlying fs modifications
audit_get_nd(): don't unlock parent too early
exportfs_decode_fh(): negative pinned may become positive without the parent locked
cgroup: don't put ERR_PTR() into fc->root
autofs: fix a leak in autofs_expire_indirect()
aio: Fix io_pgetevents() struct __compat_aio_sigset layout
fs/namespace.c: fix use-after-free of mount in mnt_warn_timestamp_expiry()
uclamp_update_active() should perform the update when
p->uclamp[clamp_id].active is true. But when the logic was inverted in
[1], the if condition wasn't inverted correctly too.
[1] https://lore.kernel.org/lkml/20190902073836.GO2369@hirez.programming.kicks-ass.net/
Reported-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Patrick Bellasi <patrick.bellasi@matbug.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: babbe170e0 ("sched/uclamp: Update CPU's refcount on TG's clamp changes")
Link: https://lkml.kernel.org/r/20191114211052.15116-1-qais.yousef@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It looks like a "static inline" has been missed in front
of the empty definition of perf_cgroup_switch() under
certain configurations.
Fixes the following sparse warning:
kernel/events/core.c:1035:1: warning: symbol 'perf_cgroup_switch' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191106132527.19977-1-ben.dooks@codethink.co.uk
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
313ccb9615 ("perf: Allocate context task_ctx_data for child event")
makes the inherit path skip over the current event in case of task_ctx_data
allocation failure. This, however, is inconsistent with allocation failures
in perf_event_alloc(), which would abort the fork.
Correct this by returning an error code on task_ctx_data allocation
failure and failing the fork in that case.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191105075702.60319-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit
ab43762ef0 ("perf: Allow normal events to output AUX data")
added 'aux_output' bit to the attribute structure, which relies on AUX
events and grouping, neither of which is supported for the kernel events.
This notwithstanding, attempts have been made to use it in the kernel
code, suggesting the necessity of an explicit hard -EINVAL.
Fix this by rejecting attributes with aux_output set for kernel events.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191030134731.5437-3-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A comment is in a wrong place in perf_event_create_kernel_counter().
Fix that.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20191030134731.5437-2-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While discussing uncore event scheduling, I noticed we do not in fact
seem to dis-allow making uncore-cgroup events. Such events make no
sense what so ever because the cgroup is a CPU local state where
uncore counts across a number of CPUs.
Disallow them.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While seemingly harmless, __sched_fork() does hrtimer_init(), which,
when DEBUG_OBJETS, can end up doing allocations.
This then results in the following lock order:
rq->lock
zone->lock.rlock
batched_entropy_u64.lock
Which in turn causes deadlocks when we do wakeups while holding that
batched_entropy lock -- as the random code does.
Solve this by moving __sched_fork() out from under rq->lock. This is
safe because nothing there relies on rq->lock, as also evident from the
other __sched_fork() callsite.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qian Cai <cai@lca.pw>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: bigeasy@linutronix.de
Cc: cl@linux.com
Cc: keescook@chromium.org
Cc: penberg@kernel.org
Cc: rientjes@google.com
Cc: thgarnie@google.com
Cc: tytso@mit.edu
Cc: will@kernel.org
Fixes: b7d5dc2107 ("random: add a spinlock_t to struct batched_entropy")
Link: https://lkml.kernel.org/r/20191001091837.GK4536@hirez.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 TSX Async Abort and iTLB Multihit mitigations from Thomas Gleixner:
"The performance deterioration departement is not proud at all of
presenting the seventh installment of speculation mitigations and
hardware misfeature workarounds:
1) TSX Async Abort (TAA) - 'The Annoying Affair'
TAA is a hardware vulnerability that allows unprivileged
speculative access to data which is available in various CPU
internal buffers by using asynchronous aborts within an Intel TSX
transactional region.
The mitigation depends on a microcode update providing a new MSR
which allows to disable TSX in the CPU. CPUs which have no
microcode update can be mitigated by disabling TSX in the BIOS if
the BIOS provides a tunable.
Newer CPUs will have a bit set which indicates that the CPU is not
vulnerable, but the MSR to disable TSX will be available
nevertheless as it is an architected MSR. That means the kernel
provides the ability to disable TSX on the kernel command line,
which is useful as TSX is a truly useful mechanism to accelerate
side channel attacks of all sorts.
2) iITLB Multihit (NX) - 'No eXcuses'
iTLB Multihit is an erratum where some Intel processors may incur
a machine check error, possibly resulting in an unrecoverable CPU
lockup, when an instruction fetch hits multiple entries in the
instruction TLB. This can occur when the page size is changed
along with either the physical address or cache type. A malicious
guest running on a virtualized system can exploit this erratum to
perform a denial of service attack.
The workaround is that KVM marks huge pages in the extended page
tables as not executable (NX). If the guest attempts to execute in
such a page, the page is broken down into 4k pages which are
marked executable. The workaround comes with a mechanism to
recover these shattered huge pages over time.
Both issues come with full documentation in the hardware
vulnerabilities section of the Linux kernel user's and administrator's
guide.
Thanks to all patch authors and reviewers who had the extraordinary
priviledge to be exposed to this nuisance.
Special thanks to Borislav Petkov for polishing the final TAA patch
set and to Paolo Bonzini for shepherding the KVM iTLB workarounds and
providing also the backports to stable kernels for those!"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/taa: Fix printing of TAA_MSG_SMT on IBRS_ALL CPUs
Documentation: Add ITLB_MULTIHIT documentation
kvm: x86: mmu: Recovery of shattered NX large pages
kvm: Add helper function for creating VM worker threads
kvm: mmu: ITLB_MULTIHIT mitigation
cpu/speculation: Uninline and export CPU mitigations helpers
x86/cpu: Add Tremont to the cpu vulnerability whitelist
x86/bugs: Add ITLB_MULTIHIT bug infrastructure
x86/tsx: Add config options to set tsx=on|off|auto
x86/speculation/taa: Add documentation for TSX Async Abort
x86/tsx: Add "auto" option to the tsx= cmdline parameter
kvm/x86: Export MDS_NO=0 to guests when TSX is enabled
x86/speculation/taa: Add sysfs reporting for TSX Async Abort
x86/speculation/taa: Add mitigation for TSX Async Abort
x86/cpu: Add a "tsx=" cmdline option with TSX disabled by default
x86/cpu: Add a helper function x86_read_arch_cap_msr()
x86/msr: Add the IA32_TSX_CTRL MSR
A cast to 'time_t' was accidentally left in place during the
conversion of __do_adjtimex() to 64-bit timestamps, so the
resulting value is incorrectly truncated.
Remove the cast so the 64-bit time gets propagated correctly.
Fixes: ead25417f8 ("timex: use __kernel_timex internally")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20191108203435.112759-2-arnd@arndb.de
Pull cgroup fix from Tejun Heo:
"There's an inadvertent preemption point in ptrace_stop() which was
reliably triggering for a test scenario significantly slowing it down.
This contains Oleg's fix to remove the unwanted preemption point"
* 'for-5.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup: freezer: call cgroup_enter_frozen() with preemption disabled in ptrace_stop()
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
Pull scheduler fixes from Thomas Gleixner:
"Two fixes for scheduler regressions:
- Plug a subtle race condition which was introduced with the rework
of the next task selection functionality. The change of task
properties became unprotected which can be observed inconsistently
causing state corruption.
- A trivial compile fix for CONFIG_CGROUPS=n"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix pick_next_task() vs 'change' pattern race
sched/core: Fix compilation error when cgroup not selected
Pull irq fixlet from Thomas Gleixner:
"A trivial fix for a kernel doc regression where an argument change was
not reflected in the documentation"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/irqdomain: Update __irq_domain_alloc_fwnode() function documentation
Pull stacktrace fix from Thomas Gleixner:
"A small fix for a stacktrace regression.
Saving a stacktrace for a foreign task skipped an extra entry which
makes e.g. the output of /proc/$PID/stack incomplete"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
stacktrace: Don't skip first entry on noncurrent tasks
if the child has been negative and just went positive
under us, we want coherent d_is_positive() and ->d_inode.
Don't unlock the parent until we'd done that work...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
the caller of ->get_tree() expects NULL left there on error...
Reported-by: Thibaut Sautereau <thibaut@sautereau.fr>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
Commit 67692435c4 ("sched: Rework pick_next_task() slow-path")
inadvertly introduced a race because it changed a previously
unexplored dependency between dropping the rq->lock and
sched_class::put_prev_task().
The comments about dropping rq->lock, in for example
newidle_balance(), only mentions the task being current and ->on_cpu
being set. But when we look at the 'change' pattern (in for example
sched_setnuma()):
queued = task_on_rq_queued(p); /* p->on_rq == TASK_ON_RQ_QUEUED */
running = task_current(rq, p); /* rq->curr == p */
if (queued)
dequeue_task(...);
if (running)
put_prev_task(...);
/* change task properties */
if (queued)
enqueue_task(...);
if (running)
set_next_task(...);
It becomes obvious that if we do this after put_prev_task() has
already been called on @p, things go sideways. This is exactly what
the commit in question allows to happen when it does:
prev->sched_class->put_prev_task(rq, prev, rf);
if (!rq->nr_running)
newidle_balance(rq, rf);
The newidle_balance() call will drop rq->lock after we've called
put_prev_task() and that allows the above 'change' pattern to
interleave and mess up the state.
Furthermore, it turns out we lost the RT-pull when we put the last DL
task.
Fix both problems by extracting the balancing from put_prev_task() and
doing a multi-class balance() pass before put_prev_task().
Fixes: 67692435c4 ("sched: Rework pick_next_task() slow-path")
Reported-by: Quentin Perret <qperret@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Quentin Perret <qperret@google.com>
Tested-by: Valentin Schneider <valentin.schneider@arm.com>
When cgroup is disabled the following compilation error was hit
kernel/sched/core.c: In function ‘uclamp_update_active_tasks’:
kernel/sched/core.c:1081:23: error: storage size of ‘it’ isn’t known
struct css_task_iter it;
^~
kernel/sched/core.c:1084:2: error: implicit declaration of function ‘css_task_iter_start’; did you mean ‘__sg_page_iter_start’? [-Werror=implicit-function-declaration]
css_task_iter_start(css, 0, &it);
^~~~~~~~~~~~~~~~~~~
__sg_page_iter_start
kernel/sched/core.c:1085:14: error: implicit declaration of function ‘css_task_iter_next’; did you mean ‘__sg_page_iter_next’? [-Werror=implicit-function-declaration]
while ((p = css_task_iter_next(&it))) {
^~~~~~~~~~~~~~~~~~
__sg_page_iter_next
kernel/sched/core.c:1091:2: error: implicit declaration of function ‘css_task_iter_end’; did you mean ‘get_task_cred’? [-Werror=implicit-function-declaration]
css_task_iter_end(&it);
^~~~~~~~~~~~~~~~~
get_task_cred
kernel/sched/core.c:1081:23: warning: unused variable ‘it’ [-Wunused-variable]
struct css_task_iter it;
^~
cc1: some warnings being treated as errors
make[2]: *** [kernel/sched/core.o] Error 1
Fix by protetion uclamp_update_active_tasks() with
CONFIG_UCLAMP_TASK_GROUP
Fixes: babbe170e0 ("sched/uclamp: Update CPU's refcount on TG's clamp changes")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Patrick Bellasi <patrick.bellasi@matbug.net>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Juri Lelli <juri.lelli@redhat.com>
Cc: Ben Segall <bsegall@google.com>
Link: https://lkml.kernel.org/r/20191105112212.596-1-qais.yousef@arm.com
We need to drop the bpf_devs_lock on error before returning.
Fixes: 9fd7c55591 ("bpf: offload: aggregate offloads per-device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Link: https://lore.kernel.org/bpf/20191104091536.GB31509@mwanda
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-02
The following pull-request contains BPF updates for your *net* tree.
We've added 6 non-merge commits during the last 6 day(s) which contain
a total of 8 files changed, 35 insertions(+), 9 deletions(-).
The main changes are:
1) Fix ppc BPF JIT's tail call implementation by performing a second pass
to gather a stable JIT context before opcode emission, from Eric Dumazet.
2) Fix build of BPF samples sys_perf_event_open() usage to compiled out
unavailable test_attr__{enabled,open} checks. Also fix potential overflows
in bpf_map_{area_alloc,charge_init} on 32 bit archs, from Björn Töpel.
3) Fix narrow loads of bpf_sysctl context fields with offset > 0 on big endian
archs like s390x and also improve the test coverage, from Ilya Leoshkevich.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQRAhzRXHqcMeLMyaSiRxhvAZXjcogUCXcGMxwAKCRCRxhvAZXjc
otEzAP9lHvP97TtRG9gP6dj6YovZ5Djdo3IscmkTqy5Nt8sVNQD+NWg1LZnSMFdJ
ExETgRVlsjF8q2sblswtn/8Ab53O6AM=
=RVGl
-----END PGP SIGNATURE-----
Merge tag 'for-linus-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull clone3 stack argument update from Christian Brauner:
"This changes clone3() to do basic stack validation and to set up the
stack depending on whether or not it is growing up or down.
With clone3() the expectation is now very simply that the .stack
argument points to the lowest address of the stack and that
.stack_size specifies the initial stack size. This is diferent from
legacy clone() where the "stack" argument had to point to the lowest
or highest address of the stack depending on the architecture.
clone3() was released with 5.3. Currently, it is not documented and
very unclear to userspace how the stack and stack_size argument have
to be passed. After talking to glibc folks we concluded that changing
clone3() to determine stack direction and doing basic validation is
the right course of action.
Note, this is a potentially user visible change. In the very unlikely
case, that it breaks someone's use-case we will revert. (And then e.g.
place the new behavior under an appropriate flag.)
Note that passing an empty stack will continue working just as before.
Breaking someone's use-case is very unlikely. Neither glibc nor musl
currently expose a wrapper for clone3(). There is currently also no
real motivation for anyone to use clone3() directly. First, because
using clone{3}() with stacks requires some assembly (see glibc and
musl). Second, because it does not provide features that legacy
clone() doesn't. New features for clone3() will first happen in v5.5
which is why v5.4 is still a good time to try and make that change now
and backport it to v5.3.
I did a codesearch on https://codesearch.debian.net, github, and
gitlab and could not find any software currently relying directly on
clone3(). I expect this to change once we land CLONE_CLEAR_SIGHAND
which was a request coming from glibc at which point they'll likely
start using it"
* tag 'for-linus-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
clone3: validate stack arguments
Validate the stack arguments and setup the stack depening on whether or not
it is growing down or up.
Legacy clone() required userspace to know in which direction the stack is
growing and pass down the stack pointer appropriately. To make things more
confusing microblaze uses a variant of the clone() syscall selected by
CONFIG_CLONE_BACKWARDS3 that takes an additional stack_size argument.
IA64 has a separate clone2() syscall which also takes an additional
stack_size argument. Finally, parisc has a stack that is growing upwards.
Userspace therefore has a lot nasty code like the following:
#define __STACK_SIZE (8 * 1024 * 1024)
pid_t sys_clone(int (*fn)(void *), void *arg, int flags, int *pidfd)
{
pid_t ret;
void *stack;
stack = malloc(__STACK_SIZE);
if (!stack)
return -ENOMEM;
#ifdef __ia64__
ret = __clone2(fn, stack, __STACK_SIZE, flags | SIGCHLD, arg, pidfd);
#elif defined(__parisc__) /* stack grows up */
ret = clone(fn, stack, flags | SIGCHLD, arg, pidfd);
#else
ret = clone(fn, stack + __STACK_SIZE, flags | SIGCHLD, arg, pidfd);
#endif
return ret;
}
or even crazier variants such as [3].
With clone3() we have the ability to validate the stack. We can check that
when stack_size is passed, the stack pointer is valid and the other way
around. We can also check that the memory area userspace gave us is fine to
use via access_ok(). Furthermore, we probably should not require
userspace to know in which direction the stack is growing. It is easy
for us to do this in the kernel and I couldn't find the original
reasoning behind exposing this detail to userspace.
/* Intentional user visible API change */
clone3() was released with 5.3. Currently, it is not documented and very
unclear to userspace how the stack and stack_size argument have to be
passed. After talking to glibc folks we concluded that trying to change
clone3() to setup the stack instead of requiring userspace to do this is
the right course of action.
Note, that this is an explicit change in user visible behavior we introduce
with this patch. If it breaks someone's use-case we will revert! (And then
e.g. place the new behavior under an appropriate flag.)
Breaking someone's use-case is very unlikely though. First, neither glibc
nor musl currently expose a wrapper for clone3(). Second, there is no real
motivation for anyone to use clone3() directly since it does not provide
features that legacy clone doesn't. New features for clone3() will first
happen in v5.5 which is why v5.4 is still a good time to try and make that
change now and backport it to v5.3. Searches on [4] did not reveal any
packages calling clone3().
[1]: https://lore.kernel.org/r/CAG48ez3q=BeNcuVTKBN79kJui4vC6nw0Bfq6xc-i0neheT17TA@mail.gmail.com
[2]: https://lore.kernel.org/r/20191028172143.4vnnjpdljfnexaq5@wittgenstein
[3]: 5238e95759/src/basic/raw-clone.h (L31)
[4]: https://codesearch.debian.net
Fixes: 7f192e3cd3 ("fork: add clone3")
Cc: Kees Cook <keescook@chromium.org>
Cc: Jann Horn <jannh@google.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Florian Weimer <fweimer@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-api@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: <stable@vger.kernel.org> # 5.3
Cc: GNU C Library <libc-alpha@sourceware.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Aleksa Sarai <cyphar@cyphar.com>
Link: https://lore.kernel.org/r/20191031113608.20713-1-christian.brauner@ubuntu.com
A recent commit changed a parameter of __irq_domain_alloc_fwnode(), but
did not update the documentation comment. Fix it up.
Fixes: b977fcf477 ("irqdomain/debugfs: Use PAs to generate fwnode names")
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1571476047-29463-1-git-send-email-wang.yi59@zte.com.cn
The update of the VDSO data is depending on __arch_use_vsyscall() returning
True. This is a leftover from the attempt to map the features of various
architectures 1:1 into generic code.
The usage of __arch_use_vsyscall() in the actual vsyscall implementations
got dropped and replaced by the requirement for the architecture code to
return U64_MAX if the global clocksource is not usable in the VDSO.
But the __arch_use_vsyscall() check in the update code stayed which causes
the VDSO data to be stale or invalid when an architecture actually
implements that function and returns False when the current clocksource is
not usable in the VDSO.
As a consequence the VDSO implementations of clock_getres(), time(),
clock_gettime(CLOCK_.*_COARSE) operate on invalid data and return bogus
information.
Remove the __arch_use_vsyscall() check from the VDSO update function and
update the VDSO data unconditionally.
[ tglx: Massaged changelog and removed the now useless implementations in
asm-generic/ARM64/MIPS ]
Fixes: 44f57d788e ("timekeeping: Provide a generic update_vsyscall() implementation")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1571887709-11447-1-git-send-email-chenhc@lemote.com
When doing cat /proc/<PID>/stack, the output is missing the first entry.
When the current code walks the stack starting in stack_trace_save_tsk,
it skips all scheduler functions (that's OK) plus one more function. But
this one function should be skipped only for the 'current' task as it is
stack_trace_save_tsk proper.
The original code (before the common infrastructure) skipped one
function only for the 'current' task -- see save_stack_trace_tsk before
3599fe12a1. So do so also in the new infrastructure now.
Fixes: 214d8ca6ee ("stacktrace: Provide common infrastructure")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Suchanek <msuchanek@suse.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20191030072545.19462-1-jslaby@suse.cz
A kernel module may need to check the value of the "mitigations=" kernel
command line parameter as part of its setup when the module needs
to perform software mitigations for a CPU flaw.
Uninline and export the helper functions surrounding the cpu_mitigations
enum to allow for their usage from a module.
Lastly, privatize the enum and cpu_mitigations variable since the value of
cpu_mitigations can be checked with the exported helper functions.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull networking fixes from David Miller:
1) Fix free/alloc races in batmanadv, from Sven Eckelmann.
2) Several leaks and other fixes in kTLS support of mlx5 driver, from
Tariq Toukan.
3) BPF devmap_hash cost calculation can overflow on 32-bit, from Toke
Høiland-Jørgensen.
4) Add an r8152 device ID, from Kazutoshi Noguchi.
5) Missing include in ipv6's addrconf.c, from Ben Dooks.
6) Use siphash in flow dissector, from Eric Dumazet. Attackers can
easily infer the 32-bit secret otherwise etc.
7) Several netdevice nesting depth fixes from Taehee Yoo.
8) Fix several KCSAN reported errors, from Eric Dumazet. For example,
when doing lockless skb_queue_empty() checks, and accessing
sk_napi_id/sk_incoming_cpu lockless as well.
9) Fix jumbo packet handling in RXRPC, from David Howells.
10) Bump SOMAXCONN and tcp_max_syn_backlog values, from Eric Dumazet.
11) Fix DMA synchronization in gve driver, from Yangchun Fu.
12) Several bpf offload fixes, from Jakub Kicinski.
13) Fix sk_page_frag() recursion during memory reclaim, from Tejun Heo.
14) Fix ping latency during high traffic rates in hisilicon driver, from
Jiangfent Xiao.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (146 commits)
net: fix installing orphaned programs
net: cls_bpf: fix NULL deref on offload filter removal
selftests: bpf: Skip write only files in debugfs
selftests: net: reuseport_dualstack: fix uninitalized parameter
r8169: fix wrong PHY ID issue with RTL8168dp
net: dsa: bcm_sf2: Fix IMP setup for port different than 8
net: phylink: Fix phylink_dbg() macro
gve: Fixes DMA synchronization.
inet: stop leaking jiffies on the wire
ixgbe: Remove duplicate clear_bit() call
Documentation: networking: device drivers: Remove stray asterisks
e1000: fix memory leaks
i40e: Fix receive buffer starvation for AF_XDP
igb: Fix constant media auto sense switching when no cable is connected
net: ethernet: arc: add the missed clk_disable_unprepare
igb: Enable media autosense for the i350.
igb/igc: Don't warn on fatal read failures when the device is removed
tcp: increase tcp_max_syn_backlog max value
net: increase SOMAXCONN to 4096
netdevsim: Fix use-after-free during device dismantle
...
Pull scheduler fixes from Ingo Molnar:
"Fix two scheduler topology bugs/oversights on Juno r0 2+4 big.LITTLE
systems"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Allow sched_asym_cpucapacity to be disabled
sched/topology: Don't try to build empty sched domains
The functions bpf_map_area_alloc() and bpf_map_charge_init() prior
this commit passed the size parameter as size_t. In this commit this
is changed to u64.
All users of these functions avoid size_t overflows on 32-bit systems,
by explicitly using u64 when calculating the allocation size and
memory charge cost. However, since the result was narrowed by the
size_t when passing size and cost to the functions, the overflow
handling was in vain.
Instead of changing all call sites to size_t and handle overflow at
the call site, the parameter is changed to u64 and checked in the
functions above.
Fixes: d407bd25a2 ("bpf: don't trigger OOM killer under pressure with map alloc")
Fixes: c85d69135a ("bpf: move memory size checks to bpf_map_charge_init()")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Link: https://lore.kernel.org/bpf/20191029154307.23053-1-bjorn.topel@gmail.com
"ctx:file_pos sysctl:read read ok narrow" works on s390 by accident: it
reads the wrong byte, which happens to have the expected value of 0.
Improve the test by seeking to the 4th byte and expecting 4 instead of
0.
This makes the latent problem apparent: the test attempts to read the
first byte of bpf_sysctl.file_pos, assuming this is the least-significant
byte, which is not the case on big-endian machines: a non-zero offset is
needed.
The point of the test is to verify narrow loads, so we cannot cheat our
way out by simply using BPF_W. The existence of the test means that such
loads have to be supported, most likely because llvm can generate them.
Fix the test by adding a big-endian variant, which uses an offset to
access the least-significant byte of bpf_sysctl.file_pos.
This reveals the final problem: verifier rejects accesses to bpf_sysctl
fields with offset > 0. Such accesses are already allowed for a wide
range of structs: __sk_buff, bpf_sock_addr and sk_msg_md to name a few.
Extend this support to bpf_sysctl by using bpf_ctx_range instead of
offsetof when matching field offsets.
Fixes: 7b146cebe3 ("bpf: Sysctl hook")
Fixes: e1550bfe0d ("bpf: Add file_pos field to bpf_sysctl ctx")
Fixes: 9a1027e525 ("selftests/bpf: Test file_pos field in bpf_sysctl ctx")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrey Ignatov <rdna@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/20191028122902.9763-1-iii@linux.ibm.com
While the static key is correctly initialized as being disabled, it will
remain forever enabled once turned on. This means that if we start with an
asymmetric system and hotplug out enough CPUs to end up with an SMP system,
the static key will remain set - which is obviously wrong. We should detect
this and turn off things like misfit migration and capacity aware wakeups.
As Quentin pointed out, having separate root domains makes this slightly
trickier. We could have exclusive cpusets that create an SMP island - IOW,
the domains within this root domain will not see any asymmetry. This means
we can't just disable the key on domain destruction, we need to count how
many asymmetric root domains we have.
Consider the following example using Juno r0 which is 2+4 big.LITTLE, where
two identical cpusets are created: they both span both big and LITTLE CPUs:
asym0 asym1
[ ][ ]
L L B L L B
$ cgcreate -g cpuset:asym0
$ cgset -r cpuset.cpus=0,1,3 asym0
$ cgset -r cpuset.mems=0 asym0
$ cgset -r cpuset.cpu_exclusive=1 asym0
$ cgcreate -g cpuset:asym1
$ cgset -r cpuset.cpus=2,4,5 asym1
$ cgset -r cpuset.mems=0 asym1
$ cgset -r cpuset.cpu_exclusive=1 asym1
$ cgset -r cpuset.sched_load_balance=0 .
(the CPU numbering may look odd because on the Juno LITTLEs are CPUs 0,3-5
and bigs are CPUs 1-2)
If we make one of those SMP (IOW remove asymmetry) by e.g. hotplugging its
big core, we would end up with an SMP cpuset and an asymmetric cpuset - the
static key must remain set, because we still have one asymmetric root domain.
With the above example, this could be done with:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
Which would result in:
asym0 asym1
[ ][ ]
L L B L L
When both SMP and asymmetric cpusets are present, all CPUs will observe
sched_asym_cpucapacity being set (it is system-wide), but not all CPUs
observe asymmetry in their sched domain hierarchy:
per_cpu(sd_asym_cpucapacity, <any CPU in asym0>) == <some SD at DIE level>
per_cpu(sd_asym_cpucapacity, <any CPU in asym1>) == NULL
Change the simple key enablement to an increment, and decrement the key
counter when destroying domains that cover asymmetric CPUs.
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Cc: Dietmar.Eggemann@arm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hannes@cmpxchg.org
Cc: lizefan@huawei.com
Cc: morten.rasmussen@arm.com
Cc: qperret@google.com
Cc: tj@kernel.org
Cc: vincent.guittot@linaro.org
Fixes: df054e8445 ("sched/topology: Add static_key for asymmetric CPU capacity optimizations")
Link: https://lkml.kernel.org/r/20191023153745.19515-3-valentin.schneider@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit:
1a59413124 ("perf: Add wakeup watermark control to the AUX area")
added attr.__reserved_2 padding, but forgot to add an ABI check to reject
attributes with this field set. Fix that.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: adrian.hunter@intel.com
Cc: mathieu.poirier@linaro.org
Link: https://lkml.kernel.org/r/20191025121636.75182-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for time(keeping):
- Add a missing include to prevent compiler warnings.
- Make the VDSO implementation of clock_getres() POSIX compliant
again. A recent change dropped the NULL pointer guard which is
required as NULL is a valid pointer value for this function.
- Fix two function documentation typos"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Fix two trivial comments
timers/sched_clock: Include local timekeeping.h for missing declarations
lib/vdso: Make clock_getres() POSIX compliant again
Pull perf fixes from Thomas Gleixner:
"A set of perf fixes:
kernel:
- Unbreak the tracking of auxiliary buffer allocations which got
imbalanced causing recource limit failures.
- Fix the fallout of splitting of ToPA entries which missed to shift
the base entry PA correctly.
- Use the correct context to lookup the AUX event when unmapping the
associated AUX buffer so the event can be stopped and the buffer
reference dropped.
tools:
- Fix buildiid-cache mode setting in copyfile_mode_ns() when copying
/proc/kcore
- Fix freeing id arrays in the event list so the correct event is
closed.
- Sync sched.h anc kvm.h headers with the kernel sources.
- Link jvmti against tools/lib/ctype.o to have weak strlcpy().
- Fix multiple memory and file descriptor leaks, found by coverity in
perf annotate.
- Fix leaks in error handling paths in 'perf c2c', 'perf kmem', found
by a static analysis tool"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/aux: Fix AUX output stopping
perf/aux: Fix tracking of auxiliary trace buffer allocation
perf/x86/intel/pt: Fix base for single entry topa
perf kmem: Fix memory leak in compact_gfp_flags()
tools headers UAPI: Sync sched.h with the kernel
tools headers kvm: Sync kvm.h headers with the kernel sources
tools headers kvm: Sync kvm headers with the kernel sources
tools headers kvm: Sync kvm headers with the kernel sources
perf c2c: Fix memory leak in build_cl_output()
perf tools: Fix mode setting in copyfile_mode_ns()
perf annotate: Fix multiple memory and file descriptor leaks
perf tools: Fix resource leak of closedir() on the error paths
perf evlist: Fix fix for freed id arrays
perf jvmti: Link against tools/lib/ctype.h to have weak strlcpy()
Daniel Borkmann says:
====================
pull-request: bpf 2019-10-27
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 11 day(s) which contain
a total of 7 files changed, 66 insertions(+), 16 deletions(-).
The main changes are:
1) Fix two use-after-free bugs in relation to RCU in jited symbol exposure to
kallsyms, from Daniel Borkmann.
2) Fix NULL pointer dereference in AF_XDP rx-only sockets, from Magnus Karlsson.
3) Fix hang in netdev unregister for hash based devmap as well as another overflow
bug on 32 bit archs in memlock cost calculation, from Toke Høiland-Jørgensen.
4) Fix wrong memory access in LWT BPF programs on reroute due to invalid dst.
Also fix BPF selftests to use more compatible nc options, from Jiri Benc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Using device PM QoS of CPU devices for managing frequency limits
in cpufreq does not work, so introduce frequency QoS (based on the
original low-level PM QoS) for this purpose, switch cpufreq and
related code over to using it and fix a race involving deferred
updates of frequency limits on top of that (Rafael Wysocki, Sudeep
Holla).
- Avoid calling regulator_enable()/disable() from the OPP framework
to avoid side-effects on boot-enabled regulators that may change their
initial voltage due to performing initial voltage balancing without
all restrictions from the consumers (Marek Szyprowski).
- Avoid a kref management issue in the OPP library code and drop an
incorrectly added lockdep_assert_held() from it (Viresh Kumar).
- Make the recently added haltpoll cpuidle driver take the 'idle='
override into account as appropriate (Zhenzhong Duan).
-----BEGIN PGP SIGNATURE-----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=yitK
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix problems related to frequency limits management in cpufreq
that were introduced during the 5.3 cycle (when PM QoS had started to
be used for that), fix a few issues in the OPP (operating performance
points) library code and fix up the recently added haltpoll cpuidle
driver.
The cpufreq changes are somewhat bigger that I would like them to be
at this stage of the cycle, but the problems fixed by them include
crashes on boot and shutdown in some cases (among other things) and in
my view it is better to address the root of the issue right away.
Specifics:
- Using device PM QoS of CPU devices for managing frequency limits in
cpufreq does not work, so introduce frequency QoS (based on the
original low-level PM QoS) for this purpose, switch cpufreq and
related code over to using it and fix a race involving deferred
updates of frequency limits on top of that (Rafael Wysocki, Sudeep
Holla).
- Avoid calling regulator_enable()/disable() from the OPP framework
to avoid side-effects on boot-enabled regulators that may change
their initial voltage due to performing initial voltage balancing
without all restrictions from the consumers (Marek Szyprowski).
- Avoid a kref management issue in the OPP library code and drop an
incorrectly added lockdep_assert_held() from it (Viresh Kumar).
- Make the recently added haltpoll cpuidle driver take the 'idle='
override into account as appropriate (Zhenzhong Duan)"
* tag 'pm-5.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
opp: Reinitialize the list_kref before adding the static OPPs again
cpufreq: Cancel policy update work scheduled before freeing
cpuidle: haltpoll: Take 'idle=' override into account
opp: core: Revert "add regulators enable and disable"
PM: QoS: Drop frequency QoS types from device PM QoS
cpufreq: Use per-policy frequency QoS
PM: QoS: Introduce frequency QoS
opp: of: drop incorrect lockdep_assert_held()
- A race in perf trace initialization (missing mutexes)
- Minor fix to represent gfp_t in synthetic events as properly signed
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXa5C9hQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qrFqAP9FskyS8xr1iqquWGarC38jYaLg8C2c
7ou+tdIm+Rez5QEA+3E456Esusmx3dACk2QLeb788Pf1wQOjKXyZ9H+2eAE=
=ys+Y
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.4-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Two minor fixes:
- A race in perf trace initialization (missing mutexes)
- Minor fix to represent gfp_t in synthetic events as properly
signed"
* tag 'trace-v5.4-rc3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix race in perf_trace_buf initialization
tracing: Fix "gfp_t" format for synthetic events
Linus Torvalds