-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl4rTdoACgkQSD+KveBX
+j5wiAgAtlGxIVKMpbJN7DIJNQ3rLGwTjPdVUFSRvHB+krVV9/ym02bIBIEphSPu
ZEF53eJMtJ0XIdUjvAyKA+zJg9p12vewbGpYV/LdjBNikHatMPGvR4grDgB9pnqT
tIxH6b4vzh5p/bMcP5l4yuVG6pf/ERdxQqsa93Op9xJzOkMH+A2KA/G32VHL2OmH
619hrWRVA/UVG0wUcOaX6ra+QA5EQ3lhcrvqL702k4JhIZPtG7Ndmm0+Z0nrDiIm
oXfc1236nc3emkijQczEZ+6oYiuYQ7WSKxZeS+8Bnmc3ZZ2w2RZrC7UCOadGzu12
+0XYfMsD2FWwEim52IZK/VMPtykjZw==
=i5Au
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2020-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2020-01-24
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
Merge conflict: once merge with net-next, a contextual conflict will
appear in drivers/net/ethernet/mellanox/mlx5/core/eswitch_offloads.c
since the code moved in net-next.
To resolve, just delete ALL of the conflicting hunk from net.
So sorry for the small mess ..
For -stable v5.4:
('net/mlx5: Update the list of the PCI supported devices')
('net/mlx5: Fix lowest FDB pool size')
('net/mlx5e: kTLS, Fix corner-case checks in TX resync flow')
('net/mlx5e: kTLS, Do not send decrypted-marked SKBs via non-accel path')
('net/mlx5: Eswitch, Prevent ingress rate configuration of uplink rep')
('net/mlx5e: kTLS, Remove redundant posts in TX resync flow')
('net/mlx5: DR, Enable counter on non-fwd-dest objects')
('net/mlx5: DR, use non preemptible call to get the current cpu number')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cxgb3 driver for "Chelsio T3-based gigabit and 10Gb Ethernet
adapters" implements a custom ioctl as SIOCCHIOCTL/SIOCDEVPRIVATE in
cxgb_extension_ioctl().
One of the subcommands of the ioctl is CHELSIO_GET_MEM, which appears
to read memory directly out of the adapter and return it to userspace.
It's not entirely clear what the contents of the adapter memory
contains, but the assumption is that it shouldn't be accessible to all
users.
So add a CAP_NET_ADMIN check to the CHELSIO_GET_MEM case. Put it after
the is_offload() check, which matches two of the other subcommands in
the same function which also check for is_offload() and CAP_NET_ADMIN.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 7587935cfa ("net: bcmgenet: move NAPI initialization to
ring initialization") moved the code, this used to be
netif_tx_napi_add(), but we lost that small semantic change in the
process, restore that.
Fixes: 7587935cfa ("net: bcmgenet: move NAPI initialization to ring initialization")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use generic device API to get phy mode to fix probe failure
with ACPI based devices.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TCP out-of-order is identified (unexpected tcp seq mismatch), driver
analyzes the packet and decides what handling should it get:
1. go to accelerated path (to be encrypted in HW),
2. go to regular xmit path (send w/o encryption),
3. drop.
Packets marked with skb->decrypted by the TLS stack in the TX flow skips
SW encryption, and rely on the HW offload.
Verify that such packets are never sent un-encrypted on the wire.
Add a WARN to catch such bugs, and prefer dropping the packet in these cases.
Fixes: 46a3ea9807 ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The call to tx_post_resync_params() is done earlier in the flow,
the post of the control WQEs is unnecessarily repeated. Remove it.
Fixes: 700ec49742 ("net/mlx5e: kTLS, Fix missing SQ edge fill")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There are the following cases:
1. Packet ends before start marker: bypass offload.
2. Packet starts before start marker and ends after it: drop,
not supported, breaks contract with kernel.
3. packet ends before tls record info starts: drop,
this packet was already acknowledged and its record info
was released.
Add the above as comment in code.
Mind possible wraparounds of the TCP seq, replace the simple comparison
with a call to the TCP before() method.
In addition, remove logic that handles negative sync_len values,
as it became impossible.
Fixes: d2ead1f360 ("net/mlx5e: Add kTLS TX HW offload support")
Fixes: 46a3ea9807 ("net/mlx5e: kTLS, Enhance TX resync flow")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently VF in LEGACY mode are not able to go up. Also in OFFLOADS
mode, when switching to it first time, VF can go up independently to
his representor, which is not expected.
Perform clearing of VF config when switching modes and set link state
to AUTO as default value. Also, when switching to OFFLOADS mode set
link state to DOWN, which allow VF link state to be controlled by its
REP.
Fixes: 1ab2068a4c ("net/mlx5: Implement vports admin state backup/restore")
Fixes: 556b9d16d3 ("net/mlx5: Clear VF's configuration on disabling SRIOV")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use raw_smp_processor_id instead of smp_processor_id() otherwise we will
get the following trace in debug-kernel:
BUG: using smp_processor_id() in preemptible [00000000] code: devlink
caller is dr_create_cq.constprop.2+0x31d/0x970 [mlx5_core]
Call Trace:
dump_stack+0x9a/0xf0
debug_smp_processor_id+0x1f3/0x200
dr_create_cq.constprop.2+0x31d/0x970
genl_family_rcv_msg+0x5fd/0x1170
genl_rcv_msg+0xb8/0x160
netlink_rcv_skb+0x11e/0x340
Fixes: 297cccebdc ("net/mlx5: DR, Expose an internal API to issue RDMA operations")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Since the implementation relies on limiting the VF transmit rate to
simulate ingress rate limiting, and since either uplink representor or
ecpf are not associated with a VF, we limit the rate limit configuration
for those ports.
Fixes: fcb64c0f56 ("net/mlx5: E-Switch, add ingress rate support")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code handles only counters that attached to dest, we still
have the cases where we have counter on non-dest, like over drop etc.
Fixes: 6a48faeeca ("net/mlx5: Add direct rule fs_cmd implementation")
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add the upcoming ConnectX-7 device ID.
Fixes: 85327a9c41 ("net/mlx5: Update the list of the PCI supported devices")
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The pool sizes represent the pool sizes in the fw. when we request
a pool size from fw, it will return the next possible group.
We track how many pools the fw has left and start requesting groups
from the big to the small.
When we start request 4k group, which doesn't exists in fw, fw
wants to allocate the next possible size, 64k, but will fail since
its exhausted. The correct smallest pool size in fw is 128 and not 4k.
Fixes: e52c280240 ("net/mlx5: E-Switch, Add chains and priorities")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.
https://bugzilla.kernel.org/show_bug.cgi?id=206283
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a hw_dbg message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 5.5.3.2 of the datasheet says,
If FIFO Underrun, Byte Count Mismatch, Excessive Collision, or
Excessive Deferral (if enabled) errors occur, transmission ceases.
In this situation, the chip asserts a TXER interrupt rather than TXDN.
But the handler for the TXDN is the only way that the transmit queue
gets restarted. Hence, an aborted transmission can result in a watchdog
timeout.
This problem can be reproduced on congested link, as that can result in
excessive transmitter collisions. Another way to reproduce this is with
a FIFO Underrun, which may be caused by DMA latency.
In event of a TXER interrupt, prevent a watchdog timeout by restarting
transmission.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 4.3.1 of the datasheet says,
This bit [TXP] must not be set if a Load CAM operation is in
progress (LCAM is set). The SONIC will lock up if both bits are
set simultaneously.
Testing has shown that the driver sometimes attempts to set LCAM
while TXP is set. Avoid this by waiting for command completion
before and after giving the LCAM command.
After issuing the Load CAM command, poll for !SONIC_CR_LCAM rather than
SONIC_INT_LCD, because the SONIC_CR_TXP bit can't be used until
!SONIC_CR_LCAM.
When in reset mode, take the opportunity to reset the CAM Enable
register.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several issues relating to command register usage during
chip initialization.
Firstly, the SONIC sometimes comes out of software reset with the
Start Timer bit set. This gets logged as,
macsonic macsonic eth0: sonic_init: status=24, i=101
Avoid this by giving the Stop Timer command earlier than later.
Secondly, the loop that waits for the Read RRA command to complete has
the break condition inverted. That's why the for loop iterates until
its termination condition. Call the helper for this instead.
Finally, give the Receiver Enable command after clearing interrupts,
not before, to avoid the possibility of losing an interrupt.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the SONIC's DMA engine is idle before altering the transmit
and receive descriptors. Add a helper for this as it will be needed
again.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as the driver is finished with a receive buffer it allocs a new
one and overwrites the corresponding RRA entry with a new buffer pointer.
Problem is, the buffer pointer is split across two word-sized registers.
It can't be updated in one atomic store. So this operation races with the
chip while it stores received packets and advances its RRP register.
This could result in memory corruption by a DMA write.
Avoid this problem by adding buffers only at the location given by the
RWP register, in accordance with the National Semiconductor datasheet.
Re-factor this code into separate functions to calculate a RRA pointer
and to update the RWP.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
After sonic_tx_timeout() calls sonic_init(), it can happen that
sonic_rx() will subsequently encounter a receive descriptor with no
flags set. Remove the comment that says that this can't happen.
When giving a receive descriptor to the SONIC, clear the descriptor
status field. That way, any rx descriptor with flags set can only be
a newly received packet.
Don't process a descriptor without the LPKT bit set. The buffer is
still in use by the SONIC.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeKX2wAAoJEG4XJFUm622bG8QH/3+QXaSJAVqzbQh2boy7aS88
xhrrnh+bSqWY0ChMk0Z73RF8Ek0WlO+os4uN1cbWIWujrdQUPbTBtOwX4d0TzTue
E3tBFPiHTlVtU43z1bsprA+6EE7fqt/H2lWtlxk0IHzeiQY9NcB6BlDKKCzk5Hib
aMb5HCQy4JmSK83E60HLM9L4nEmEP+yveaKL7uaAZw+qkmyk2mT6um0TlmOYVoNG
9V6k3OZto8LvyV6jKPZgVI6QBATnwHDxlWgooYRj54PuCj9hTbR2mcuUL2QyQeze
AX2QNI+1kWIrAiDaU/lOj8579SiUl36iqtuKmtLhDnSe1GxDkrzmawtz3aGDm4k=
=VZox
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2020-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.5
Second set of fixes for v5.5. There are quite a few patches,
especially on iwlwifi, due to me being on a long break. Libertas also
has a security fix and mt76 a build fix.
iwlwifi
* don't send the PPAG command when PPAG is disabled, since it can cause problems
* a few fixes for a HW bug
* a fix for RS offload;
* a fix for 3168 devices where the NVM tables where the wrong tables were being read
* fix a couple of potential memory leaks in TXQ code
* disable L0S states in all hardware since our hardware doesn't
officially support them anymore (and older versions of the hardware
had instability in these states)
* remove lar_disable parameter since it has been causing issues for
some people who erroneously disable it
* force the debug monitor HW to stop also when debug is disabled,
since it sometimes stays on and prevents low system power states
* don't send IWL_MVM_RXQ_NSSN_SYNC notification due to DMA problems
libertas
* fix two buffer overflows
mt76
* build fix related to CONFIG_MT76_LEDS
* fix off by one in bitrates handling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If both IFF_NAPI_FRAGS mode and XDP are enabled, and the XDP program
consumes the skb, we need to clear the napi.skb (or risk
a use-after-free) and release the mutex (or risk a deadlock)
WARNING: lock held when returning to user space!
5.5.0-rc6-syzkaller #0 Not tainted
------------------------------------------------
syz-executor.0/455 is leaving the kernel with locks still held!
1 lock held by syz-executor.0/455:
#0: ffff888098f6e748 (&tfile->napi_mutex){+.+.}, at: tun_get_user+0x1604/0x3fc0 drivers/net/tun.c:1835
Fixes: 90e33d4594 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Petar Penkov <ppenkov@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling this, the device would wait an internal signal which
wouldn't be triggered. Then, the device couldn't enter P3 mode, so
the power consumption is increased.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid the MCU to clear the lanwake after suspending. It may cause the
WOL fail. Disable LANWAKE_CLR_EN before suspending. Besides,enable it
and reset the lanwake status when resuming or initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain platforms, it causes USB reset periodically.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8153B with QFN32, disable test IO. Otherwise, it may cause
abnormal behavior for the device randomly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PLA MCU clock speed down could only be enabled when tx/rx are disabled.
Otherwise, the packet loss may occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initailization would reset runtime suspend by tp->saved_wolopts, so
the tp->saved_wolopts should be set before initializing.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When linking ON, the patch of flow control has to be reset. This
makes sure the patch works normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the runtime resume doesn't work normally for linking change.
1. Reset the settings and status of runtime suspend.
2. Sync the linking status.
3. Poll the linking change.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command. Some of the commands are handled in readrids(),
where the user controlled command is converted into a driver-internal
value called "ridcode".
There are two command values, AIROGWEPKTMP and AIROGWEPKNV, which
correspond to ridcode values of RID_WEP_TEMP and RID_WEP_PERM
respectively. These commands both have checks that the user has
CAP_NET_ADMIN, with the comment that "Only super-user can read WEP
keys", otherwise they return -EPERM.
However there is another command value, AIRORRID, that lets the user
specify the ridcode value directly, with no other checks. This means
the user can bypass the CAP_NET_ADMIN check on AIROGWEPKTMP and
AIROGWEPKNV.
Fix it by moving the CAP_NET_ADMIN check out of the command handling
and instead do it later based on the ridcode. That way regardless of
whether the ridcode is set via AIROGWEPKTMP or AIROGWEPKNV, or passed
in using AIRORID, we always do the CAP_NET_ADMIN check.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver for Cisco Aironet 4500 and 4800 series cards (airo.c),
implements AIROOLDIOCTL/SIOCDEVPRIVATE in airo_ioctl().
The ioctl handler copies an aironet_ioctl struct from userspace, which
includes a command and a length. Some of the commands are handled in
readrids(), which kmalloc()'s a buffer of RIDSIZE (2048) bytes.
That buffer is then passed to PC4500_readrid(), which has two cases.
The else case does some setup and then reads up to RIDSIZE bytes from
the hardware into the kmalloc()'ed buffer.
Here len == RIDSIZE, pBuf is the kmalloc()'ed buffer:
// read the rid length field
bap_read(ai, pBuf, 2, BAP1);
// length for remaining part of rid
len = min(len, (int)le16_to_cpu(*(__le16*)pBuf)) - 2;
...
// read remainder of the rid
rc = bap_read(ai, ((__le16*)pBuf)+1, len, BAP1);
PC4500_readrid() then returns to readrids() which does:
len = comp->len;
if (copy_to_user(comp->data, iobuf, min(len, (int)RIDSIZE))) {
Where comp->len is the user controlled length field.
So if the "rid length field" returned by the hardware is < 2048, and
the user requests 2048 bytes in comp->len, we will leak the previous
contents of the kmalloc()'ed buffer to userspace.
Fix it by kzalloc()'ing the buffer.
Found by Ilja by code inspection, not tested as I don't have the
required hardware.
Reported-by: Ilja Van Sprundel <ivansprundel@ioactive.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Cc: Alexander Lobakin <alobakin@dlink.ru>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_wakeup can happen in parallel with close/hangup where tty->disc_data
is set to NULL and the netdevice is freed thus also freeing
disc_data. write_wakeup accesses disc_data so we must prevent close from
freeing the netdev while write_wakeup has a non-NULL view of
tty->disc_data.
We also need to make sure that accesses to disc_data are atomic. Which can
all be done with RCU.
This problem was found by Syzkaller on SLCAN, but the same issue is
reproducible with the SLIP line discipline using an LTP test based on the
Syzkaller reproducer.
A fix which didn't use RCU was posted by Hillf Danton.
Fixes: 661f7fda21 ("slip: Fix deadlock in write_wakeup")
Fixes: a8e83b1753 ("slcan: Port write_wakeup deadlock fix from slip")
Reported-by: syzbot+017e491ae13c0068598a@syzkaller.appspotmail.com
Signed-off-by: Richard Palethorpe <rpalethorpe@suse.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Tyler Hall <tylerwhall@gmail.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: syzkaller@googlegroups.com
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831ac12356b695ff054bef641b9e99593:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
CC: <stable@vger.kernel.org> # 5.3+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Eric Dumazet, there are still some outstanding
cases where the driver does not handle TSO correctly when skb's
are over a certain size. Most cases have been fixed, this patch
should ensure that forwarded SKB's that are greater than
MAX_SINGLE_PACKET_SIZE - TX_OVERHEAD are software segmented
and handled correctly.
Signed-off-by: James Hughes <james.hughes@raspberrypi.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller