G_PRINTER: Adds a USB printer gadget driver for use in printer firmware.
This adds a USB printer gadget driver for use in printer firmware.
The printer gadget channels data between the USB host and a userspace
program driving the print engine. The user space program reads and
writes the device file /dev/g_printer to receive or send printer data.
It can use ioctl calls to the device file to get or set printer status.
Signed-off-by: Craig W. Nadler <craig@nadler.us>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1014) was partly written by Tilman Schmidt. It
clarifies the USB power-management documentation by explaining that
when a disconnect occurs, a suspend method call might not be followed
by either a resume or a reset_resume call.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as998) adds documentation on how USB power management
works and how to use it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements a USB serial port driver for the Winchiphead
CH341 USB-RS232 Converter. This chip also implements an IEEE 1284
parallel port, I2C and SPI, but that is not supported by the driver.
Signed-off-by: Frank A Kingswood <frank@kingswood-consulting.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update usbmon documentation, mentioning the "zero" (wildcard) bus.
Possibly, in my first hunk, the 'either ... or ...' should be rephrased a bit to
be expressed better.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates some of the documentation about DMA buffer management
for USB, and ways to avoid extra copying. Our understanding of the issues
has improved over time.
- Most drivers should *avoid* the dma-coherent allocators. There are
a few exceptions (like the HID driver).
- Some methods are currently commented out; it seems folk writing
USB drivers aren't doing performance tuning at that level yet.
- Just avoid highmem; there's no good way to pass an "I can do highmem
DMA" capability through a driver stack. This is easy, everything
already avoids highmem. But it'd be nice if x86_32 systems with much
physical memory could use it directly with network adapters and mass
storage devices. (Patch, anyone?)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as920) adds an extra level of protection to the
USB-Persist facility. Now it will apply by default only to hubs; for
all other devices the user must enable it explicitly by setting the
power/persist device attribute.
The disconnect_all_children() routine in hub.c has been removed and
its code placed inline. This is the way it was originally as part of
hub_pre_reset(); the revised usage in hub_reset_resume() is
sufficiently different that the code can no longer be shared.
Likewise, mark_children_for_reset() is now inline as part of
hub_reset_resume(). The end result looks much cleaner than before.
The sysfs interface is updated to add the new attribute file, and
there are corresponding documentation updates.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.
The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now. But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert files within the Documentation directory to UTF-8.
Adrian Bunk:
small additional fixes
Signed-off-by: John Anthony Kazos Jr. <jakj@j-a-k-j.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
I am no longer with CTI. The Support Department will handle all
inquiries regarding the WH.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a new text API, codenamed '1u', which captures more URB
fields than old '1t' interface did. Also the '1u' text API is compatible
with the future "bus zero" extension.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new, "binary" API in addition to the old, text API usbmon
had before. The new API allows for less CPU use, and it allows to capture
all data from a packet where old API only captured 32 bytes at most. There
are some limitations and conditions to this, e.g. in case someone constructs
a URB with 1GB of data, it's not likely to be captured, because even the
huge buffers of the new reader are finite. Nonetheless, I expect this new
capability to capture all data for all real life scenarios.
The downside is, a special user mode application is required where cat(1)
worked before. I have sample code at http://people.redhat.com/zaitcev/linux/
and Paolo Abeni is working on patching libpcap.
This patch was initially written by Paolo and later I tweaked it, and
we had a little back-and-forth. So this is a jointly authored patch, but
I am submitting this I am responsible for the bugs.
Signed-off-by: Paolo Abeni <paolo.abeni@email.it>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update /proc/bus/usb/devices output to report active altsettings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This changes a few mentions of my email address to point to the new one,
leaving things like old copyright messages alone.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes typos in various Documentation txts. The patch addresses some
misc words.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses some
+words starting with the letter 'T'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch add AIRcable USBto USB-HID blacklist, makes some little
changes things in the Kconfig to make AIRcable USB look as all the rest
of drivers. And it removes the readme part that was on
Documentation/usb/usb-serial.txt because it is not needed anymore.
Signed-off-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove many duplicated words under Documentation/ and do other small
cleanups.
Examples:
"and and" --> "and"
"in in" --> "in"
"the the" --> "the"
"the the" --> "to the"
...
Signed-off-by: Paolo Ornati <ornati@fastwebnet.it>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letter 'S'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Alan Cox <alan@redhat.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'N'-'P'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. The patch addresses
some words starting with the letters 'H'-'M'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This patch fixes typos in various Documentation txts. This patch addresses
some words starting with the letters 'D'-'E'.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Now that devfs is removed, there's no longer any need to document how to
do this or that with devfs.
This patch includes some improvements by Joe Perches.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add driver for AIRcable USB Bluetooth dongle.
Signed-off-by: Naranjo, Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the documentation. Apparently, I left unedited copy-paste results
in examples. Also, Alan helped me to improve the most confusing parts.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Move documentation for usb v4l devices from
Documentation/usb to Documentation/video4linux.
- Removed trailing whitespace.
- Update Kconfig help text links to reflect the new file locations.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ZC0301 driver updates.
Changes: + new, - removed, * cleanup, @ bugfix
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Cleanups and updates in the documentation
+ Use per-device sensor structures
+ Add frame_timeout module parameter
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: ET61X[12]51 driver updates
Changes: + new, - removed, * cleanup, @ bugfix
@ Fix stream_interrupt()
@ Fix vidioc_enum_input() and split vidioc_gs_input()
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
when waiting for video frames
* replace wake_up_interruptible(&wait_stream) with wake_up(&wait_stream)
* Cleanups and updates in the documentation
* Use mutexes instead of semaphores
+ Use per-device sensor structures
+ Add support for PAS202BCA image sensors
+ Add frame_timeout module parameter
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates.
Changes: + new, - removed, * cleanup, @ bugfix
@ Fix stream_interrupt()
@ Fix vidioc_enum_input() and split vidioc_gs_input()
@ Need usb_get|put_dev() when disconnecting, if the device is open
* Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
when waiting for video frames
* replace wake_up_interruptible(&wait_stream) with wake_up(&wait_stream)
* Cleanups and updates in the documentation
+ Use per-device sensor structures
+ Add support for PAS202BCA image sensors
+ Add frame_timeout module parameter
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"Cosmetic" driver updates for the ZC0301 driver:
- Fix stream_interrupt() (and work around a possible kernel bug);
- Fix vidioc_enum_input() and split vidioc_gs_input() in two parts;
- Use wait_event_interruptible_timeout() instead of wait_event_interruptible()
when waiting for video frames;
- replace erroneous wake_up_interruptible(&wait_stream) with
wake_up(&wait_stream);
- Cosmetic cleanups in the documentation.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver for ZC0301
Image Processor and Control Chip.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- the w9968cf-vpp module is not intended for inclusion into the kernel
- the upstream w9968cf package shipping the w9968cf-vpp module suggests
to simply replace the w9968cf module shipped with the kernel
Therefore, there seems to be no good reason spending some bytes of
kernel memory for hooks for the w9968cf-vpp module.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a Video4Linux2 driver giving support
to ET61X151 and ET61X251 PC Camera Controllers made by
Etoms Electronics.
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Signed-off-by: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as611) fixes a minor mistake and misspelling in the USB
documentation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Correct lots of URLs in Documentation/ Also a few minor whitespace cleanups
and typo/spello fixes. Sadly there are still a lot of bad URLs remaining.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch deletes the bluetooth.txt help file of the bluetty driver and
hands over its major device nodes for character devices to the RFCOMM TTY
implementation of the Bluetooth subsystem.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (as564) updates Documentation/usb/URB.txt, bringing it roughly
up to the current level.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update Documentation/usb/proc_usb_info.txt:
- remove some trailing whitespace
- add a blank line before each T: line to match current kernel
and to make the text more readable.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The attached patch fixes the following spelling errors in Documentation/
- double "the"
- Several misspellings of function/functionality
- infomation
- memeory
- Recieved
- wether
and possibly others which I forgot ;-)
Trailing whitespaces on the same line as the typo are also deleted.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make usbmon to print Setup packets of Control transfers. This is useful
when debugging enumeration issues.
This is a change to the trace format which is not fully compatible.
A parser has to look at the data length word now. If that word is
a character like 's', read setup packet before proceeding with data.
I decided not to bump the API tag for this because not many such
parsers exist at this point.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Robert P. J. Day