commit 316ec15481 upstream.
A page table upgrade in a kernel section that uses secondary address
mode will mess up the kernel instructions as follows:
Consider the following scenario: two threads are sharing memory.
On CPU1 thread 1 does e.g. strnlen_user(). That gets to
old_fs = enable_sacf_uaccess();
len = strnlen_user_srst(src, size);
and
" la %2,0(%1)\n"
" la %3,0(%0,%1)\n"
" slgr %0,%0\n"
" sacf 256\n"
"0: srst %3,%2\n"
in strnlen_user_srst(). At that point we are in secondary space mode,
control register 1 points to kernel page table and instruction fetching
happens via c1, rather than usual c13. Interrupts are not disabled, for
obvious reasons.
On CPU2 thread 2 does MAP_FIXED mmap(), forcing the upgrade of page table
from 3-level to e.g. 4-level one. We'd allocated new top-level table,
set it up and now we hit this:
notify = 1;
spin_unlock_bh(&mm->page_table_lock);
}
if (notify)
on_each_cpu(__crst_table_upgrade, mm, 0);
OK, we need to actually change over to use of new page table and we
need that to happen in all threads that are currently running. Which
happens to include the thread 1. IPI is delivered and we have
static void __crst_table_upgrade(void *arg)
{
struct mm_struct *mm = arg;
if (current->active_mm == mm)
set_user_asce(mm);
__tlb_flush_local();
}
run on CPU1. That does
static inline void set_user_asce(struct mm_struct *mm)
{
S390_lowcore.user_asce = mm->context.asce;
OK, user page table address updated...
__ctl_load(S390_lowcore.user_asce, 1, 1);
... and control register 1 set to it.
clear_cpu_flag(CIF_ASCE_PRIMARY);
}
IPI is run in home space mode, so it's fine - insns are fetched
using c13, which always points to kernel page table. But as soon
as we return from the interrupt, previous PSW is restored, putting
CPU1 back into secondary space mode, at which point we no longer
get the kernel instructions from the kernel mapping.
The fix is to only fixup the control registers that are currently in use
for user processes during the page table update. We must also disable
interrupts in enable_sacf_uaccess to synchronize the cr and
thread.mm_segment updates against the on_each-cpu.
Fixes: 0aaba41b58 ("s390: remove all code using the access register mode")
Cc: stable@vger.kernel.org # 4.15+
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
References: CVE-2020-11884
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add support for IBM z15 machines.
- Add SHA3 and CCA AES cipher key support in zcrypt and pkey refactoring.
- Move to arch_stack_walk infrastructure for the stack unwinder.
- Various kasan fixes and improvements.
- Various command line parsing fixes.
- Improve decompressor phase debuggability.
- Lift no bss usage restriction for the early code.
- Use refcount_t for reference counters for couple of places in
mm code.
- Logging improvements and return code fix in vfio-ccw code.
- Couple of zpci fixes and minor refactoring.
- Remove some outdated documentation.
- Fix secure boot detection.
- Other various minor code clean ups.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl1/pRoACgkQjYWKoQLX
FBjxLQf/Y1nlmoc8URLqaqfNTczIvUzdfXuahI7L75RoIIiqHtcHBrVwauSr7Lma
XVRzK/+6q0UPISrOIZEEtQKsMMM7rGuUv/+XTyrOB/Tsc31kN2EIRXltfXI/lkb8
BZdgch4Xs2rOD7y6TvqpYJsXYXsnLMWwCk8V+48V/pok4sEgMDgh0bTQRHPHYmZ6
1cv8ZQ0AeuVxC6ChM30LhajGRPkYd8RQ82K7fU7jxT0Tjzu66SyrW3pTwA5empBD
RI2yBZJ8EXwJyTCpvN8NKiBgihDs9oUZl61Dyq3j64Mb1OuNUhxXA/8jmtnGn0ok
O9vtImCWzExhjSMkvotuhHEC05nEEQ==
=LCgE
-----END PGP SIGNATURE-----
Merge tag 's390-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for IBM z15 machines.
- Add SHA3 and CCA AES cipher key support in zcrypt and pkey
refactoring.
- Move to arch_stack_walk infrastructure for the stack unwinder.
- Various kasan fixes and improvements.
- Various command line parsing fixes.
- Improve decompressor phase debuggability.
- Lift no bss usage restriction for the early code.
- Use refcount_t for reference counters for couple of places in mm
code.
- Logging improvements and return code fix in vfio-ccw code.
- Couple of zpci fixes and minor refactoring.
- Remove some outdated documentation.
- Fix secure boot detection.
- Other various minor code clean ups.
* tag 's390-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (48 commits)
s390: remove pointless drivers-y in drivers/s390/Makefile
s390/cpum_sf: Fix line length and format string
s390/pci: fix MSI message data
s390: add support for IBM z15 machines
s390/crypto: Support for SHA3 via CPACF (MSA6)
s390/startup: add pgm check info printing
s390/crypto: xts-aes-s390 fix extra run-time crypto self tests finding
vfio-ccw: fix error return code in vfio_ccw_sch_init()
s390: vfio-ap: fix warning reset not completed
s390/base: remove unused s390_base_mcck_handler
s390/sclp: Fix bit checked for has_sipl
s390/zcrypt: fix wrong handling of cca cipher keygenflags
s390/kasan: add kdump support
s390/setup: avoid using strncmp with hardcoded length
s390/sclp: avoid using strncmp with hardcoded length
s390/module: avoid using strncmp with hardcoded length
s390/pci: avoid using strncmp with hardcoded length
s390/kaslr: reserve memory for kasan usage
s390/mem_detect: provide single get_mem_detect_end
s390/cmma: reuse kstrtobool for option value parsing
...
Clean uncompressed kernel .bss section in the startup code before
the uncompressed kernel is executed. At this point of time initrd and
certificates have been already rescued. Uncompressed kernel .bss size
is known from vmlinux_info. It is also taken into consideration during
uncompressed kernel positioning by kaslr (so it is safe to clean it).
With that uncompressed kernel is starting with .bss section zeroed and
no .bss section usage restrictions apply. Which makes chkbss checks for
uncompressed kernel objects obsolete and they can be removed.
early_nobss.c is also not needed anymore. Parts of it which are still
relevant are moved to early.c. Kasan initialization code is now called
directly from head64 (early.c is instrumented and should not be
executed before kasan shadow memory is set up).
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Include <asm/xor.h> into arch/s390/lib/xor.c to expose xor_block_xc
declaration and avoid the following sparse warning:
arch/s390/lib/xor.c:128:27: warning: symbol 'xor_block_xc' was not declared. Should it be static?
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
There never have been distributions that shiped with CONFIG_SMP=n for
s390. In addition the kernel currently doesn't even compile with
CONFIG_SMP=n for s390. Most likely it wouldn't even work, even if we
fix the compile error, since nobody tests it, since there is no use
case that I can think of.
Therefore simply enforce CONFIG_SMP and get rid of some more or
less unused code.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
The assembler code in arch/s390 misses proper ENDPROC statements
to properly end functions in a few places. Add them.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Avoid using arch specific implementations of string/memory functions
with KASAN since gcc cannot instrument asm code memory accesses and
many bugs could be missed.
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Kasan instrumentation adds "store" check for variables marked as
modified by inline assembly. With user pointers containing addresses
from another address space this produces false positives.
static inline unsigned long clear_user_xc(void __user *to, ...)
{
asm volatile(
...
: "+a" (to) ...
User space access functions are wrapped by manually instrumented
functions in kasan common code, which should be sufficient to catch
errors. So, we just disable uaccess.o instrumentation altogether.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Follow the common kasan approach:
"KASan replaces memory functions with manually instrumented
variants. Original functions declared as weak symbols so strong
definitions in mm/kasan/kasan.c could replace them. Original
functions have aliases with '__' prefix in name, so we could call
non-instrumented variant if needed."
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The memove, memset, memcpy, __memset16, __memset32 and __memset64
function have an additional indirect return branch in form of a
"bzr" instruction. These need to use expolines as well.
Cc: <stable@vger.kernel.org> # v4.17+
Fixes: 97489e0663 ("s390/lib: use expoline for indirect branches")
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce compile time check for files which should avoid using .bss
section, because of the following reasons:
- .bss section has not been zeroed yet,
- initrd has not been moved to a safe location and could be overlapping
with .bss section.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The return from the memmove, memset, memcpy, __memset16, __memset32 and
__memset64 functions are done with "br %r14". These are indirect branches
as well and need to use execute trampolines for CONFIG_EXPOLINE=y.
Cc: stable@vger.kernel.org # 4.16
Fixes: f19fbd5ed6 ("s390: introduce execute-trampolines for branches")
Reviewed-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With CONFIG_PREEMPT=y there is a possible race in disable_sacf_uaccess.
The new set_fs value needs to be stored the the task structure first,
the control register update needs to be second. Otherwise a preemptive
schedule may interrupt the code right after the control register update
has been done and the next time the task is scheduled we get an incorrect
value in the control register due to the old set_fs setting.
Fixes: 0aaba41b58 ("s390: remove all code using the access register mode")
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vdso code for the getcpu() and the clock_gettime() call use the access
register mode to access the per-CPU vdso data page with the current code.
An alternative to the complicated AR mode is to use the secondary space
mode. This makes the vdso faster and quite a bit simpler. The downside is
that the uaccess code has to be changed quite a bit.
Which instructions are used depends on the machine and what kind of uaccess
operation is requested. The instruction dictates which ASCE value needs
to be loaded into %cr1 and %cr7.
The different cases:
* User copy with MVCOS for z10 and newer machines
The MVCOS instruction can copy between the primary space (aka user) and
the home space (aka kernel) directly. For set_fs(KERNEL_DS) the kernel
ASCE is loaded into %cr1. For set_fs(USER_DS) the user space is already
loaded in %cr1.
* User copy with MVCP/MVCS for older machines
To be able to execute the MVCP/MVCS instructions the kernel needs to
switch to primary mode. The control register %cr1 has to be set to the
kernel ASCE and %cr7 to either the kernel ASCE or the user ASCE dependent
on set_fs(KERNEL_DS) vs set_fs(USER_DS).
* Data access in the user address space for strnlen / futex
To use "normal" instruction with data from the user address space the
secondary space mode is used. The kernel needs to switch to primary mode,
%cr1 has to contain the kernel ASCE and %cr7 either the user ASCE or the
kernel ASCE, dependent on set_fs.
To load a new value into %cr1 or %cr7 is an expensive operation, the kernel
tries to be lazy about it. E.g. for multiple user copies in a row with
MVCP/MVCS the replacement of the vdso ASCE in %cr7 with the user ASCE is
done only once. On return to user space a CPU bit is checked that loads the
vdso ASCE again.
To enable and disable the data access via the secondary space two new
functions are added, enable_sacf_uaccess and disable_sacf_uaccess. The fact
that a context is in secondary space uaccess mode is stored in the
mm_segment_t value for the task. The code of an interrupt may use set_fs
as long as it returns to the previous state it got with get_fs with another
call to set_fs. The code in finish_arch_post_lock_switch simply has to do a
set_fs with the current mm_segment_t value for the task.
For CPUs with MVCOS:
CPU running in | %cr1 ASCE | %cr7 ASCE |
--------------------------------------|-----------|-----------|
user space | user | vdso |
kernel, USER_DS, normal-mode | user | vdso |
kernel, USER_DS, normal-mode, lazy | user | user |
kernel, USER_DS, sacf-mode | kernel | user |
kernel, KERNEL_DS, normal-mode | kernel | vdso |
kernel, KERNEL_DS, normal-mode, lazy | kernel | kernel |
kernel, KERNEL_DS, sacf-mode | kernel | kernel |
For CPUs without MVCOS:
CPU running in | %cr1 ASCE | %cr7 ASCE |
--------------------------------------|-----------|-----------|
user space | user | vdso |
kernel, USER_DS, normal-mode | user | vdso |
kernel, USER_DS, normal-mode lazy | kernel | user |
kernel, USER_DS, sacf-mode | kernel | user |
kernel, KERNEL_DS, normal-mode | kernel | vdso |
kernel, KERNEL_DS, normal-mode, lazy | kernel | kernel |
kernel, KERNEL_DS, sacf-mode | kernel | kernel |
The lines with "lazy" refer to the state after a copy via the secondary
space with a delayed reload of %cr1 and %cr7.
There are three hardware address spaces that can cause a DAT exception,
primary, secondary and home space. The exception can be related to
four different fault types: user space fault, vdso fault, kernel fault,
and the gmap faults.
Dependent on the set_fs state and normal vs. sacf mode there are a number
of fault combinations:
1) user address space fault via the primary ASCE
2) gmap address space fault via the primary ASCE
3) kernel address space fault via the primary ASCE for machines with
MVCOS and set_fs(KERNEL_DS)
4) vdso address space faults via the secondary ASCE with an invalid
address while running in secondary space in problem state
5) user address space fault via the secondary ASCE for user-copy
based on the secondary space mode, e.g. futex_ops or strnlen_user
6) kernel address space fault via the secondary ASCE for user-copy
with secondary space mode with set_fs(KERNEL_DS)
7) kernel address space fault via the primary ASCE for user-copy
with secondary space mode with set_fs(USER_DS) on machines without
MVCOS.
8) kernel address space fault via the home space ASCE
Replace user_space_fault() with a new function get_fault_type() that
can distinguish all four different fault types.
With these changes the futex atomic ops from the kernel and the
strnlen_user will get a little bit slower, as well as the old style
uaccess with MVCP/MVCS. All user accesses based on MVCOS will be as
fast as before. On the positive side, the user space vdso code is a
lot faster and Linux ceases to use the complicated AR mode.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Pull core locking updates from Ingo Molnar:
"The main changes in this cycle are:
- Another attempt at enabling cross-release lockdep dependency
tracking (automatically part of CONFIG_PROVE_LOCKING=y), this time
with better performance and fewer false positives. (Byungchul Park)
- Introduce lockdep_assert_irqs_enabled()/disabled() and convert
open-coded equivalents to lockdep variants. (Frederic Weisbecker)
- Add down_read_killable() and use it in the VFS's iterate_dir()
method. (Kirill Tkhai)
- Convert remaining uses of ACCESS_ONCE() to
READ_ONCE()/WRITE_ONCE(). Most of the conversion was Coccinelle
driven. (Mark Rutland, Paul E. McKenney)
- Get rid of lockless_dereference(), by strengthening Alpha atomics,
strengthening READ_ONCE() with smp_read_barrier_depends() and thus
being able to convert users of lockless_dereference() to
READ_ONCE(). (Will Deacon)
- Various micro-optimizations:
- better PV qspinlocks (Waiman Long),
- better x86 barriers (Michael S. Tsirkin)
- better x86 refcounts (Kees Cook)
- ... plus other fixes and enhancements. (Borislav Petkov, Juergen
Gross, Miguel Bernal Marin)"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
locking/x86: Use LOCK ADD for smp_mb() instead of MFENCE
rcu: Use lockdep to assert IRQs are disabled/enabled
netpoll: Use lockdep to assert IRQs are disabled/enabled
timers/posix-cpu-timers: Use lockdep to assert IRQs are disabled/enabled
sched/clock, sched/cputime: Use lockdep to assert IRQs are disabled/enabled
irq_work: Use lockdep to assert IRQs are disabled/enabled
irq/timings: Use lockdep to assert IRQs are disabled/enabled
perf/core: Use lockdep to assert IRQs are disabled/enabled
x86: Use lockdep to assert IRQs are disabled/enabled
smp/core: Use lockdep to assert IRQs are disabled/enabled
timers/hrtimer: Use lockdep to assert IRQs are disabled/enabled
timers/nohz: Use lockdep to assert IRQs are disabled/enabled
workqueue: Use lockdep to assert IRQs are disabled/enabled
irq/softirqs: Use lockdep to assert IRQs are disabled/enabled
locking/lockdep: Add IRQs disabled/enabled assertion APIs: lockdep_assert_irqs_enabled()/disabled()
locking/pvqspinlock: Implement hybrid PV queued/unfair locks
locking/rwlocks: Fix comments
x86/paravirt: Set up the virt_spin_lock_key after static keys get initialized
block, locking/lockdep: Assign a lock_class per gendisk used for wait_for_completion()
workqueue: Remove now redundant lock acquisitions wrt. workqueue flushes
...
Pull s390 updates from Heiko Carstens:
"Since Martin is on vacation you get the s390 pull request for the
v4.15 merge window this time from me.
Besides a lot of cleanups and bug fixes these are the most important
changes:
- a new regset for runtime instrumentation registers
- hardware accelerated AES-GCM support for the aes_s390 module
- support for the new CEX6S crypto cards
- support for FORTIFY_SOURCE
- addition of missing z13 and new z14 instructions to the in-kernel
disassembler
- generate opcode tables for the in-kernel disassembler out of a
simple text file instead of having to manually maintain those
tables
- fast memset16, memset32 and memset64 implementations
- removal of named saved segment support
- hardware counter support for z14
- queued spinlocks and queued rwlocks implementations for s390
- use the stack_depth tracking feature for s390 BPF JIT
- a new s390_sthyi system call which emulates the sthyi (store
hypervisor information) instruction
- removal of the old KVM virtio transport
- an s390 specific CPU alternatives implementation which is used in
the new spinlock code"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (88 commits)
MAINTAINERS: add virtio-ccw.h to virtio/s390 section
s390/noexec: execute kexec datamover without DAT
s390: fix transactional execution control register handling
s390/bpf: take advantage of stack_depth tracking
s390: simplify transactional execution elf hwcap handling
s390/zcrypt: Rework struct ap_qact_ap_info.
s390/virtio: remove unused header file kvm_virtio.h
s390: avoid undefined behaviour
s390/disassembler: generate opcode tables from text file
s390/disassembler: remove insn_to_mnemonic()
s390/dasd: avoid calling do_gettimeofday()
s390: vfio-ccw: Do not attempt to free no-op, test and tic cda.
s390: remove named saved segment support
s390/archrandom: Reconsider s390 arch random implementation
s390/pci: do not require AIS facility
s390/qdio: sanitize put_indicator
s390/qdio: use atomic_cmpxchg
s390/nmi: avoid using long-displacement facility
s390: pass endianness info to sparse
s390/decompressor: remove informational messages
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Enable niai instruction in the spinlock code at run-time for machines
on which facility 49 is available (zEC12 and newer).
Signed-off-by: Vasily Gorbik <gor@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Just some trivial changes like removing the extern keyword from the
header file, renaming arguments to match the man pages, and whitespace
removal.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Like for the memset16/32/64 variants avoid that subsequent mvc
instructions depend on each other since that might have negative
performance impacts.
This patch is currently hardly relevant since at least gcc 7.1
generates only inline memset code and not a single memset call.
However there is no reason to not provide an optimized version
just in case gcc generates memset calls again, like it did in
the past.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide fast versions of the new memset variants. E.g. the generic
memset64 is ten times slower than the optimized version if used on a
whole page.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Like the common queued rwlock code the s390 implementation uses the
queued spinlock code on a spinlock_t embedded in the rwlock_t to achieve
the queueing. The encoding of the rwlock_t differs though, the counter
field in the rwlock_t is split into two parts. The upper two bytes hold
the write bit and the write wait counter, the lower two bytes hold the
read counter.
The arch_read_lock operation works exactly like the common qrwlock but
the enqueue operation for a writer follows a diffent logic. After the
failed inline try to get the rwlock in write, the writer first increases
the write wait counter, acquires the wait spin_lock for the queueing,
and then loops until there are no readers and the write bit is zero.
Without the write wait counter a CPU that just released the rwlock
could immediately reacquire the lock in the inline code, bypassing all
outstanding read and write waiters. For s390 this would cause massive
imbalances in favour of writers in case of a contended rwlock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The queued spinlock code for s390 follows the principles of the common
code qspinlock implementation but with a few notable differences.
The format of the spinlock_t locking word differs, s390 needs to store
the logical CPU number of the lock holder in the spinlock_t to be able
to use the diagnose 9c directed yield hypervisor call.
The inline code sequences for spin_lock and spin_unlock are nice and
short. The inline portion of a spin_lock now typically looks like this:
lhi %r0,0 # 0 indicates an empty lock
l %r1,0x3a0 # CPU number + 1 from lowcore
cs %r0,%r1,<some_lock> # lock operation
jnz call_wait # on failure call wait function
locked:
...
call_wait:
la %r2,<some_lock>
brasl %r14,arch_spin_lock_wait
j locked
A spin_unlock is as simple as before:
lhi %r0,0
sth %r0,2(%r2) # unlock operation
After a CPU has queued itself it may not enable interrupts again for the
arch_spin_lock_flags() variant. The arch_spin_lock_wait_flags wait function
is removed.
To improve performance the code implements opportunistic lock stealing.
If the wait function finds a spinlock_t that indicates that the lock is
free but there are queued waiters, the CPU may steal the lock up to three
times without queueing itself. The lock stealing update the steal counter
in the lock word to prevent more than 3 steals. The counter is reset at
the time the CPU next in the queue successfully takes the lock.
While the queued spinlocks improve performance in a system with dedicated
CPUs, in a virtualized environment with continuously overcommitted CPUs
the queued spinlocks can have a negative effect on performance. This
is due to the fact that a queued CPU that is preempted by the hypervisor
will block the queue at some point even without holding the lock. With
the classic spinlock it does not matter if a CPU is preempted that waits
for the lock. Therefore use the queued spinlock code only if the system
runs with dedicated CPUs and fall back to classic spinlocks when running
with shared CPUs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The queued spinlock code will come out simpler if the encoding of
the CPU that holds the spinlock is (cpu+1) instead of (~cpu).
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the kernel is compiled for z10 or later machines the uaccess
code inlines the mvcos instruction. The facility bit 27 which
indicates the availability of MVCOS has to be set. The have_mvcos
jump label will always be true.
Make the generation of the have_mvcos jump label conditional on
!CONFIG_HAVE_MARCH_Z10_FEATURES.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The z14 machine introduces new mode of the next-instruction-access-intent
NIAI instruction. With NIAI-8 it is possible to pin a cache-line on a
CPU for a small amount of time, NIAI-7 releases the cache-line again.
Finally NIAI-4 can be used to prevent the CPU to speculatively access
memory beyond the compare-and-swap instruction to get the lock.
Use these instruction in the spinlock code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The TOD epoch extension adds 8 epoch bits to the TOD clock to provide
a continuous clock after 2042/09/17. The store-clock-extended (STCKE)
instruction will store the epoch index in the first byte of the
16 bytes stored by the instruction. The read_boot_clock64 and the
read_presistent_clock64 functions need to take the additional bits
into account to give the correct result after 2042/09/17.
The clock-comparator register will stay 64 bit wide. The comparison
of the clock-comparator with the TOD clock is limited to bytes
1 to 8 of the extended TOD format. To deal with the overflow problem
due to an epoch change the clock-comparator sign control in CR0 can
be used to switch the comparison of the 64-bit TOD clock with the
clock-comparator to a signed comparison.
The decision between the signed vs. unsigned clock-comparator
comparisons is done at boot time. Only if the TOD clock is in the
second half of a 142 year epoch the signed comparison is used.
This solves the epoch overflow issue as long as the machine is
booted at least once in an epoch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The average string that is copied from user space to kernel space is
rather short. E.g. booting a system involves about 50.000
strncpy_from_user() calls where the NULL terminated string has an
average size of 27 bytes.
By default our s390 specific strncpy_from_user() implementation
however copies up to 4096 bytes, which is a waste of cpu cycles and
cache lines. Therefore reduce the default length to L1_CACHE_BYTES
(256 bytes), which also reduces the average execution time of
strncpy_from_user() by 30-40%.
Alternatively we could have switched to the generic
strncpy_from_user() implementation, however it turned out that that
variant would be slower than the now optimized s390 variant.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following compile error(s) if CONFIG_KPROBES is disabled:
arch/s390/kernel/uprobes.c:79:14:
error: implicit declaration of function 'probe_get_fixup_type'
arch/s390/kernel/uprobes.c:87:14:
error: 'FIXUP_PSW_NORMAL' undeclared (first use in this function)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 updates from Martin Schwidefsky:
- three merges for KVM/s390 with changes for vfio-ccw and cpacf. The
patches are included in the KVM tree as well, let git sort it out.
- add the new 'trng' random number generator
- provide the secure key verification API for the pkey interface
- introduce the z13 cpu counters to perf
- add a new system call to set up the guarded storage facility
- simplify TASK_SIZE and arch_get_unmapped_area
- export the raw STSI data related to CPU topology to user space
- ... and the usual churn of bug-fixes and cleanups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (74 commits)
s390/crypt: use the correct module alias for paes_s390.
s390/cpacf: Introduce kma instruction
s390/cpacf: query instructions use unique parameters for compatibility with KMA
s390/trng: Introduce s390 TRNG device driver.
s390/crypto: Provide s390 specific arch random functionality.
s390/crypto: Add new subfunctions to the cpacf PRNO function.
s390/crypto: Renaming PPNO to PRNO.
s390/pageattr: avoid unnecessary page table splitting
s390/mm: simplify arch_get_unmapped_area[_topdown]
s390/mm: make TASK_SIZE independent from the number of page table levels
s390/gs: add regset for the guarded storage broadcast control block
s390/kvm: Add use_cmma field to mm_context_t
s390/kvm: Add PGSTE manipulation functions
vfio: ccw: improve error handling for vfio_ccw_mdev_remove
vfio: ccw: remove unnecessary NULL checks of a pointer
s390/spinlock: remove compare and delay instruction
s390/spinlock: use atomic primitives for spinlocks
s390/cpumf: simplify detection of guest samples
s390/pci: remove forward declaration
s390/pci: increase the PCI_NR_FUNCTIONS default
...
The CAD instruction never worked quite as expected for the spinlock
code. It has been disabled by default with git commit 61b0b01686,
if the "cad" kernel parameter is specified it is enabled for both user
space and the spinlock code. Leave the option to enable the instruction
for user space but remove it from the spinlock code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a couple more __atomic_xxx function to atomic_ops.h and use them
to replace the compare-and-swap inlines in the spinlock code. This
changes the type of the lock value from unsigned int to int.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the last places of ACCESS_ONCE in s390 code.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. The advantage
in doing so is that module.h itself sources about 15 other headers;
adding significantly to what we feed cpp, and it can obscure what
headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each change instance
for the presence of either and replace as needed. An instance
where module_param was used without moduleparam.h was also fixed,
as well as implicit use of ptrace.h and string.h headers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve the memmove implementation to save one instruction and use
better label names. Also use better label names for the memset and
memcpy implementations so everything looks consistent.
Suggested-by: Jens Remus <jremus@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We have a couple of inline assemblies like memchr() and strlen() that
read from memory, but tell the compiler only they need the addresses
of the strings they access.
This allows the compiler to omit the initialization of such strings
and therefore generate broken code. Add the missing memory barrier to
all string related inline assemblies to fix this potential issue. It
looks like the compiler currently does not generate broken code due to
these bugs.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 updates from Martin Schwidefsky:
"The main bulk of the s390 patches for the 4.10 merge window:
- Add support for the contiguous memory allocator.
- The recovery for I/O errors in the dasd device driver is improved,
the driver will now remove channel paths that are not working
properly.
- Additional fields are added to /proc/sysinfo, the extended
partition name and the partition UUID.
- New naming for PCI devices with system defined UIDs.
- The last few remaining alloc_bootmem calls are converted to
memblock.
- The thread_info structure is stripped down and moved to the
task_struct. The only field left in thread_info is the flags field.
- Rework of the arch topology code to fix a fake numa issue.
- Refactoring of the atomic primitives and add a new preempt_count
implementation.
- Clocksource steering for the STP sync check offsets.
- The s390 specific headers are changed to make them usable with
CLANG.
- Bug fixes and cleanup"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (70 commits)
s390/cpumf: Use configuration level indication for sampling data
s390: provide memmove implementation
s390: cleanup arch/s390/kernel Makefile
s390: fix initrd corruptions with gcov/kcov instrumented kernels
s390: exclude early C code from gcov profiling
s390/dasd: channel path aware error recovery
s390/dasd: extend dasd path handling
s390: remove unused labels from entry.S
s390/vmlogrdr: fix IUCV buffer allocation
s390/crypto: unlock on error in prng_tdes_read()
s390/sysinfo: show partition extended name and UUID if available
s390/numa: pin all possible cpus to nodes early
s390/numa: establish cpu to node mapping early
s390/topology: use cpu_topology array instead of per cpu variable
s390/smp: initialize cpu_present_mask in setup_arch
s390/topology: always use s390 specific sched_domain_topology_level
s390/smp: use smp_get_base_cpu() helper function
s390/numa: always use logical cpu and core ids
s390: Remove VLAIS in ptff() and clear_table()
s390: fix machine check panic stack switch
...
Provide an s390 specific memmove implementation which is faster than
the generic implementation which copies byte-wise.
For non-destructive (as defined by the mvc instruction) memmove
operations the following table compares the old default implementation
versus the new s390 specific implementation:
size old new
1 1ns 8ns
2 2ns 8ns
4 4ns 8ns
8 7ns 8ns
16 17ns 8ns
32 35ns 8ns
64 65ns 9ns
128 146ns 10ns
256 298ns 11ns
512 537ns 11ns
1024 1193ns 19ns
2048 2405ns 36ns
So only for very small sizes the old implementation is faster. For
overlapping memmoves, where the mvc instruction can't be used, the new
implementation is as slow as the old one.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull kbuild updates from Michal Marek:
- EXPORT_SYMBOL for asm source by Al Viro.
This does bring a regression, because genksyms no longer generates
checksums for these symbols (CONFIG_MODVERSIONS). Nick Piggin is
working on a patch to fix this.
Plus, we are talking about functions like strcpy(), which rarely
change prototypes.
- Fixes for PPC fallout of the above by Stephen Rothwell and Nick
Piggin
- fixdep speedup by Alexey Dobriyan.
- preparatory work by Nick Piggin to allow architectures to build with
-ffunction-sections, -fdata-sections and --gc-sections
- CONFIG_THIN_ARCHIVES support by Stephen Rothwell
- fix for filenames with colons in the initramfs source by me.
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (22 commits)
initramfs: Escape colons in depfile
ppc: there is no clear_pages to export
powerpc/64: whitelist unresolved modversions CRCs
kbuild: -ffunction-sections fix for archs with conflicting sections
kbuild: add arch specific post-link Makefile
kbuild: allow archs to select link dead code/data elimination
kbuild: allow architectures to use thin archives instead of ld -r
kbuild: Regenerate genksyms lexer
kbuild: genksyms fix for typeof handling
fixdep: faster CONFIG_ search
ia64: move exports to definitions
sparc32: debride memcpy.S a bit
[sparc] unify 32bit and 64bit string.h
sparc: move exports to definitions
ppc: move exports to definitions
arm: move exports to definitions
s390: move exports to definitions
m68k: move exports to definitions
alpha: move exports to actual definitions
x86: move exports to actual definitions
...
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes, minor cleanup and a change to the default
config"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dasd: fix failing CUIR assignment under LPAR
s390/pageattr: handle numpages parameter correctly
s390/dasd: fix hanging device after clear subchannel
s390/qdio: avoid reschedule of outbound tasklet once killed
s390/qdio: remove checks for ccw device internal state
s390/qdio: fix double return code evaluation
s390/qdio: get rid of spin_lock_irqsave usage
s390/cio: remove subchannel_id from ccw_device_private
s390/qdio: obtain subchannel_id via ccw_device_get_schid()
s390/cio: stop using subchannel_id from ccw_device_private
s390/config: make the vector optimized crc function builtin
s390/lib: fix memcmp and strstr
s390/crc32-vx: Fix checksum calculation for small sizes
s390: clarify compressed image code path
if two string compare equal the clcle instruction will update the
string addresses to point _after_ the string. This might already
be on a different page, so we should not use these pointer to
calculate the difference as in that case the calculation of the
difference can cause oopses.
The return value of memcmp does not need the difference, we
can just reuse the condition code and return for CC=1 (All bytes
compared, first operand low) -1 and for CC=2 (All bytes compared,
first operand high) +1
strstr also does not need the diff.
While fixing this, make the common function clcle "correct on its
own" by using l1 instead of l2 for the first length. strstr will
call this with l2 for both strings.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: db7f5eef3d ("s390/lib: use basic blocks for inline assemblies")
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use only simple inline assemblies which consist of a single basic
block if the register asm construct is being used.
Otherwise gcc would generate broken code if the compiler option
--sanitize-coverage=trace-pc would be used.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Christian Borntraeger