Make the computation of a memory mask representing the width of the memory
bus into a function so that it can be re-used by the ETR driver.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-16-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CoreSight TMC-ETR must have the non-secure invasive debug access
enabled for use by self-hosted tracing. Without it, there is no
point in enabling the ETR. So, let us check it in the TMC_AUTHSTATUS
register and fail the probe if it is disabled.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20190829202842.580-7-mathieu.poirier@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we have reused the name of the "platform" device for
the CoreSight device. But this is not very intuitive when
we move to ACPI. Also, the ACPI device names have ":" in them
(e.g, ARMHC97C:01), which the perf tool doesn't like very much.
This patch introduces a generic naming scheme, givin more intuitive
names for the devices that appear on the CoreSight bus.
The names follow the pattern "prefix" followed by "index" (e.g, etm5).
We maintain a list of allocated devices per "prefix" to make sure
we don't allocate a new name when it is reprobed (e.g, due to
unsatisifed device dependencies). So, we maintain the list
of "fwnodes" of the parent devices to allocate a consistent name.
All devices except the ETMs get an index allocated in the order
of probing. ETMs get an index based on the CPU they are attached to.
TMC devices are named using "tmc_etf", "tmc_etb", and "tmc_etr"
prefixes depending on the configuration of the device.
The replicators and funnels are not classified as dynamic/static
anymore. One could easily figure that out by checking the presence
of "mgmt" registers under sysfs.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to introduce methods to clean up the platform data
as we switch to tracking the device reference from "name" to "fwnode
handles" for device connections. This requires us to drop the fwnode
handle references when the data is no longer required - i.e, when
the device probe fails or the device gets unregistered.
In order to consolidate the invocation of the cleanup, we delay the
platform probing to the very last minute, possibly before invoking
the coresight_register. Then, we leave the coresight core code to
do the clean up. i.e, if the coresight_register fails, it takes
care of freeing the data. Otherwise, coresight_unregister will
do the necessary operations.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to use a name independent of the parent AMBA device
name. As such, there is no need to have it in the platform description.
Let us move this to coresight description instead.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So far we have hard coded the DT platform parsing code in
every driver. Introduce generic helper to parse the information
provided by the firmware in a platform agnostic manner, in preparation
for the ACPI support.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we are about to refactor the platform specific handling,
make the default buffer size probing generic.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to use a consistent device naming scheme,
clean up the device link tracking in replicator driver.
Use the "coresight" device instead of the "real" parent device
for all internal purposes. All other requests (e.g, power management,
DMA operations) must use the "real" device which is the parent device.
Since the CATU driver also uses the TMC-SG infrastructure, update
the callers to ensure they pass the appropriate device argument
for the tables.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for CPU-wide trace scenarios by making sure that
only the sources monitoring the same process have access to a common sink.
Because the sink is shared between sources, the first source to use the
sink switches it on while the last one does the cleanup. Any attempt to
modify the HW is overlooked for as long as more than one source is using
a sink.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In CPU-wide scenarios with an N:1 source/sink topology, sources share
the same sink. In order to reuse the same sink for all sources an
IDR is needed to archive events that have already been accounted for.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Tested-by: Robert Walker <robert.walker@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the power only if we were successful in probing the device.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we failed to setup the DMA mask for TMC-ETR, report the
error before failing the probe.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CoreSight specification (ARM IHI 0029E), updates the ID register
requirements for components on an AMBA bus, to cover both traditional
ARM Primecell type devices, and newer CoreSight and other components.
The Peripheral ID (PID) / Component ID (CID) pair is extended in certain
cases to uniquely identify components. CoreSight components related to
a single function can share Peripheral ID values, and must be further
identified using a Unique Component Identifier (UCI). e.g. the ETM, CTI,
PMU and Debug hardware of the A35 all share the same PID.
Bits 15:12 of the CID are defined to be the device class.
Class 0xF remains for PrimeCell and legacy components.
Class 0x9 defines the component as CoreSight (CORESIGHT_CID above)
Class 0x0, 0x1, 0xB, 0xE define components that do not have driver support
at present.
Class 0x2-0x8,0xA and 0xD-0xD are presently reserved.
The specification futher defines which classes of device use the standard
CID/PID pair, and when additional ID registers are required.
This patch introduces the amba_cs_uci_id structure which will be used in
all coresight drivers for indentification via the private data pointer in
the amba_id structure.
Existing drivers that currently use the amba_id->data pointer for private
data are updated to use the amba_cs_uci_id->data pointer. Macros and
inline functions are added to simplify this code.
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Convert component enable/disable messages from dev_info to dev_dbg.
When used with perf, the components in the paths are enabled/disabled
during each schedule of the run, which can flood the dmesg with these
messages. Moreover, they are only useful for debug purposes. So,
convert such messages to dev_dbg() which can be turned on as
needed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can dynamically switch between contiguous memory and
SG table depending on the trace buffer size, provide the support
for selecting an appropriate buffer size.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are about to add the support for ETR builtin scatter-gather mode
for dealing with large amount of trace buffers. However, on some of
the platforms, using the ETR SG mode can lock up the system due to
the way the ETR is connected to the memory subsystem.
In SG mode, the ETR performs READ from the scatter-gather table to
fetch the next page and regular WRITE of trace data. If the READ
operation doesn't complete(due to the memory subsystem issues,
which we have seen on a couple of platforms) the trace WRITE
cannot proceed leading to issues. So, we by default do not
use the SG mode, unless it is known to be safe on the platform.
We define a DT property for the TMC node to specify whether we
have a proper SG mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: John Horley <john.horley@arm.com>
Cc: Robert Walker <robert.walker@arm.com>
Cc: devicetree@vger.kernel.org
Cc: frowand.list@gmail.com
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per coresight standards, PIDR2 register has the following format :
[2-0] - JEP106_bits6to4
[3] - JEDEC, designer ID is specified by JEDEC.
However some of the drivers only use mask of 0x3 for the PIDR2 leaving
bits [3-2] unchecked, which could potentially match the component for
a different device altogether. This patch fixes the mask and the
corresponding id bits for the existing devices.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amba_id are not supposed to change at runtime. All functions
working with const amba_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight SoC 600 supports ETR save-restore which allows us
to restore a trace session by retaining the RRP/RWP/STS.Full values
when the TMC leaves the Disabled state. However, the TMC doesn't
have a scatter-gather unit in built.
Also, TMCs have different PIDs in different configurations (ETF,
ETB & ETR), unlike the previous generation.
While the DEVID exposes some of the features/changes in the TMC,
it doesn't explicitly advertises the new save-restore feature
as described above.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TMC in Coresight SoC-600 advertises the AXI address width
in the device configuration register.
Bit 16 - AXIAW_VALID
0 - AXI Address Width not valid
1 - Valid AXI Address width in Bits[23-17]
Bits [23-17] - AXIAW. If AXIAW_VALID = b01 then
0x20 - 32bit AXI address bus
0x28 - 40bit AXI address bus
0x2c - 44bit AXI address bus
0x30 - 48bit AXI address bus
0x34 - 52bit AXI address bus
Use the address bits from the device configuration register, if
available. Otherwise, default to 40bit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SG unit in the TMC has been removed in Coresight SoC-600.
This is however advertised by DEVID:Bit 24 = 0b1. On the
previous generation, the bit is RES0, hence we can rely on the
DEVID to detect the support.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With new version of TMC ETR, there are differing set of
features supported by the TMC. Add the capability of a
given TMC ETR for making safer decisions at runtime.
The device configuration register of the TMC (DEVID) lists
some of the capabilities. So, we can detect some of them at
probe. However, some of the features (or changes in behavior)
are not advertised and we have to depend on the PID to infer
the features. So we use a static description of the "unadvertised"
capabilities attached to the PID. Combining both, the static
and the dynamic capabilities, we maintain a bitmask of the
available features which can be later checked to take
appropriate actions.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight SoC 600 defines a new configuration for TMC, Embedded Trace
Streamer (ETS), indicated by 0x3 in MODE:CONFIG_TYPE. This would break
the existing driver which will treat anything other than ETR/ETB as an
ETF. Fix the driver to check the configuration type properly and also
add a warning if we encounter an unsupported configuration (ETS).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the new helpers for exposing coresight component registers,
choosing the 64bit variants for appropriate registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before making any DMA API calls, the ETR driver should really be setting
its masks to ensure that DMA is possible. Especially since it can
address more than the 32-bit default mask set by the AMBA bus code.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get a few warnings when building kernel with W=1:
drivers/hwtracing/coresight/coresight-tmc-etr.c:23:6: warning: no previous prototype for 'tmc_etr_enable_hw' [-Wmissing-prototypes]
drivers/hwtracing/coresight/coresight-tmc-etf.c:25:6: warning: no previous prototype for 'tmc_etb_enable_hw' [-Wmissing-prototypes]
drivers/hwtracing/coresight/coresight-tmc.c:250:9: warning: no previous prototype for ‘trigger_cntr_show’ [-Wmissing-prototypes]
...
In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
so this patch marks these functions with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ETM registers are classified into 2 categories: trace and management.
The core power domain contains most of the trace unit logic including
all(except TRCOSLAR and TRCOSLSR) the trace registers. The debug power
domain contains the external debugger interface including all management
registers.
This patch adds coresight unit specific function coresight_simple_func
which can be used for ETM trace registers by providing a ETM specific
read function which does smp cross call to ensure the trace core is
powered up before the register is accessed.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each coresight device prepares a description for coresight_register()
in struct coresight_desc. Once we register the device, the description is
useless and can be freed. The coresight_desc is small enough (48bytes on
64bit)i to be allocated on the stack. Hence use an automatic variable to
avoid a needless dynamic allocation and wasting the memory(which will only
be free'd when the device is destroyed).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we encounter a timeout waiting for a status change via
coresight_timeout, the caller always print the offset which
was tried. This is pretty much useless as it doesn't specify
the bit position we wait for. Also, one needs to lookup the
TRM to figure out, what was wrong. This patch changes all
such error messages to print something more meaningful.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present the ETF or ETR gives out the entire device
buffer, even if there is less or even no trace data
available. This patch limits the trace data given out to
the actual trace data collected.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up the error handling path for tmc_probe
as a side effect of the removal of the spurious dma_free_coherent().
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de5461970b ("coresight: tmc: allocating memory when needed")
removed the static allocation of buffer for the trace data in ETR mode in
tmc_probe. However it failed to remove the "devm_free_coherent" in
tmc_probe when the probe fails due to other reasons. This patch gets
rid of the incorrect dma_free_coherent() call.
Fixes: commit de5461970b ("coresight: tmc: allocating memory when needed")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing the HW configuration register each time the memory
width is needed simply doesn't make sense. It is much more
efficient to read the value once and keep a reference for
later use.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allowing multiple readers to access the trace data simultaniously
via sysFS provides no shortage of opportunity for race condition,
mandates two variable to be maintained (drvdata::read_count and
drvdata::reading), makes the code complex and provide little
advantages, if any.
This patch streamlines the read process by restricting trace data
access to a single user. That way drvdata::read_count can
be eliminated and race conditions (along with faulty error handling)
in function tmc_open() and tmc_release() eliminated.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In it's current form the TMC probe() function allocates
trace buffer memory at boot time, event if coresight isn't
used. This is highly inefficient since trace buffers can
occupy a lot of memory that could be used otherwised.
This patch allocates trace buffers on the fly, when the
coresight subsystem is solicited. Allocated buffers are
released when traces are read using the device descriptors
under /dev.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dealing with HW related matters in tmc_read_prepare/unprepare
becomes convoluted when many cases need to be handled distinctively.
As such moving processing related to HW setup to individual driver
files and keep the core driver generic.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC block can operate in 3 modes (ETB, ETF and ETR) and accessed
via two interfaces (sysFS and Perf). That makes 6 mode to cover, which
is way too much coupling for a single file.
This patch splits the original TMC driver in 2 halves, one for ETB/ETF
and another one for ETR mode. A common core is kept for functionality
common to all 3 modes.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch first move the TMC_STS_TMCREADY_BIT and
TMC_FFCR_FLUSHMAN_BIT defines to their respective section.
It also removes TMC_FFCR_FLUSHMAN, since the same result
can easily be obtained using the BIT() macro.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amount of #define, enumeration and structure definition
is big enough to justify moving them to a new header file.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the name of the define reflect the amount of
data tranfers per burst, in this case 16.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In their current implementation the tmc_read_prepare/unprepare()
are a lump of if/else that is difficult to read. This patch is
alleviating that by using a switch statement. The latter also
allows for a better control on the error path.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the TRM before programming the TMC in circular
buffer mode (and that for any configuration, ETB, ETR, ETF),
the TMCReady bit in the status register has to be set.
This patch adds a check to make sure the state machine is in
a state where it can be configured, and complains otherwise.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the TMC architectural state machine, the 'stopped'
state is reached when bit 2 (TMCReady) of the TMC Status register
turns to '1'. The code is correct but the naming convention isn't.
The 'Triggered' bit occupies position '1' of the TMC Status register
and has nothing to do with the indication of the TMC entering the
stopped state. As such renaming function "tmc_wait_for_triggered()"
and changing the #define to reflect what the code is really doing.
This patch has no effect other than clarifying the semantic.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding management registers that convey implementation
specific characteristics. Those are useful for trace
configuration and collection along with general trouble
shooting.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing boot time log for drivers that don't report useful information
other than they came up properly. The same information can be found in
sysFS once the system has booted and as such doesn't provide any value
in the boot log.
Reported-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of the Kconfig currently controlling compilation of any of
the files here are tristate, meaning that none of it currently
is being built as a module by anyone.
We need not be concerned about .remove functions and blocking the
unbind sysfs operations, since that was already done in a recent
commit.
Lets remove any remaining modular references, so that when reading the
drivers there is no doubt they are builtin-only.
All drivers get mostly the same changes, so they are handled in batch.
Changes are (1) convert to builtin_amba_driver, (2) delete module.h
include where unused, and (3) relocate the description into the
comments so we don't need MODULE_DESCRIPTION and associated tags.
The etm3x and etm4x use module_param_named, and have been adjusted
to just include moduleparam.h for that purpose.
In commit f309d44431 ("platform_device:
better support builtin boilerplate avoidance") we introduced the
builtin_driver macro.
Here we use that support and extend it to amba driver registration,
so where a driver is clearly non-modular and builtin-only, we can
update with the simple mapping of
module_amba_driver(...) ---> builtin_amba_driver(...)
Since module_amba_driver() uses the same init level priority as
builtin_amba_driver() the init ordering remains unchanged with
this commit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding an operation mode to the sink->enable() API in order
to prevent simultaneous access from different callers.
TPIU and TMC won't be supplemented with the AUX area
API immediately and as such ignore the new mode.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mathieu Poirier