[ Upstream commit fe56d05ee6 ]
During CSA, we briefly nullify the phy context, in __iwl_mvm_unassign_vif_chanctx.
In case we have a FW assert right after it, it remains NULL though.
We end up running into endless loop due to mac80211 trying repeatedly to
move us to ASSOC state, and we keep returning -EINVAL. Later down the road
we hit a kernel panic.
Detect and avoid this endless loop.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d64de2c17bff.Iedd0d2afa20a2aacba5259a5cae31cb3a119a4eb@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edb625208d ]
On some platforms, the preset values aren't correct and then we may
get a completion timeout in the firmware. Change the LTR configuration
to avoid that. The firmware will do some more complex reinit of this
later, but for the boot process we use ~250usec.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.d83d591c05ba.I42885c9fb500bc08b9a4c07c4ff3d436cc7a3c84@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04516706bb ]
When we read device memory, we lock a spinlock, write the address we
want to read from the device and then spin in a loop reading the data
in 32-bit quantities from another register.
As the description makes clear, this is rather inefficient, incurring
a PCIe bus transaction for every read. In a typical device today, we
want to read 786k SMEM if it crashes, leading to 192k register reads.
Occasionally, we've seen the whole loop take over 20 seconds and then
triggering the soft lockup detector.
Clearly, it is unreasonable to spin here for such extended periods of
time.
To fix this, break the loop down into an outer and an inner loop, and
break out of the inner loop if more than half a second elapsed. To
avoid too much overhead, check for that only every 128 reads, though
there's no particular reason for that number. Then, unlock and relock
to obtain NIC access again, reprogram the start address and continue.
This will keep (interrupt) latencies on the CPU down to a reasonable
time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201022165103.45878a7e49aa.I3b9b9c5a10002915072312ce75b68ed5b3dc6e14@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97cc16943f ]
We use mvm->queue_sync_state to wait for synchronous queue sync
messages, but if an async one happens inbetween we shouldn't
clear mvm->queue_sync_state after sending the async one, that
can run concurrently (at least from the CPU POV) with another
synchronous queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201107104557.51a3148f2c14.I0772171dbaec87433a11513e9586d98b5d920b5f@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 903b3f9bad ]
A print in the remain on channel code was too long and caused
a WARNING, split it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: dc28e12f21 ("iwlwifi: mvm: ROC: Extend the ROC max delay duration & limit ROC duration")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930102759.58d57c0bdc68.Ib06008665e7bf1199c360aa92691d9c74fb84990@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9018fd7f2a ]
On failure pcie_capability_read_dword() sets it's last parameter, val
to 0. However, with Patch 14/14, it is possible that val is set to ~0 on
failure. This would introduce a bug because (x & x) == (~0 & x).
This bug can be avoided without changing the function's behaviour if the
return value of pcie_capability_read_dword is checked to confirm success.
Check the return value of pcie_capability_read_dword() to ensure success.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200713175529.29715-3-refactormyself@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fbb1461ad1 upstream.
iwl_mvm_free_inactive_queue() will sleep in synchronize_net() under
some circumstances, so don't call it under RCU. There doesn't appear
to be a need for RCU protection around this particular call.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200403112332.0f49448c133d.I17fd308bc4a9491859c9b112f4eb5d2c3fc18d7d@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f327236df2 ]
When mvm is initialized we alloc aux station with aux queue.
We later free the station memory when driver is stopped, but we
never free the queue's memory, which casues a leak.
Add a proper de-initialization of the station.
Signed-off-by: Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200529092401.0121c5be55e9.Id7516fbb3482131d0c9dfb51ff20b226617ddb49@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a65a582429 ]
If we set amsdu_len one after another the second one overwrites
the orig_amsdu_len so allow only moving from debug to non debug state.
Also the TLC update check was wrong: it was checking that also the orig
is smaller then the new updated size, which is not the case in debug
amsdu mode.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: af2984e9e6 ("iwlwifi: mvm: add a debugfs entry to set a fixed size AMSDU for all TX packets")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200424182644.e565446a4fce.I9729d8c520d8b8bb4de9a5cdc62e01eb85168aac@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3f20e0982 ]
We had a check on !NVM_EXT and then a check for NVM_SDP in the else
block of this if. The else block, obviously, could only be reached if
using NVM_EXT, so it would never be NVM_SDP.
Fix that by checking whether the nvm_type is IWL_NVM instead of
checking for !IWL_NVM_EXT to solve this issue.
Reported-by: Stefan Sperling <stsp@stsp.name>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e6d419f943 upstream.
The function iwl_mvm_remove_inactive_tids() returns bool, so we
should just check "if (ret)", not "if (ret >= 0)" (which would
do nothing useful here). We obviously therefore cannot use the
return value of the function for the free_queue, we need to use
the queue (i) we're currently dealing with instead.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.9d862ed72535.I9e27ccc3ee3c8855fc13682592b571581925dfbd@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5b72e3bc4 upstream.
Due to some hardware issues, queue 31 isn't usable on devices that have
32 queues (7000, 8000, 9000 families), which is correctly reflected in
the configuration and TX queue initialization.
However, the firmware API and queue allocation code assumes that there
are 32 queues, and if something actually attempts to use #31 this leads
to a NULL-pointer dereference since it's not allocated.
Fix this by limiting to 31 in the IWL_MVM_DQA_MAX_DATA_QUEUE, and also
add some code to catch this earlier in the future, if the configuration
changes perhaps.
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.98a79be2db6a.I3a4af6b03b87a6bc18db9b1ff9a812f397bee1fc@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b98b33d556 upstream.
The iwl_trans_pcie_dyn_txq_free() function only releases the frames
that may be left on the queue by calling iwl_pcie_gen2_txq_unmap(),
but doesn't actually free the DMA ring or byte-count tables for the
queue. This leads to pretty large memory leaks (at least before my
queue size improvements), in particular in monitor/sniffer mode on
channel hopping since this happens on every channel change.
This was also now more evident after the move to a DMA pool for the
byte count tables, showing messages such as
BUG iwlwifi:bc (...): Objects remaining in iwlwifi:bc on __kmem_cache_shutdown()
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=206811.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: 6b35ff9157 ("iwlwifi: pcie: introduce a000 TX queues management")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.f5f4c4193ec1.Id5feebc9b4318041913a9c89fc1378bb5454292c@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cb5f3ea46 upstream.
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 699b760bd2 upstream.
If the firmware is in a bad state or not initialized fully, sending
the DBGC_SUSPEND_RESUME command fails but we can still collect logs.
Instead of aborting the entire dump process, simply ignore the error.
By removing the last callpoint that was checking the return value, we
can also convert the function to return void.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 576058330f ("iwlwifi: dbg: support debug recording suspend resume command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.dcec37b2efd4.I8dcd190431d110a6a0e88095ce93591ccfb3d78d@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a5688e600e upstream.
The TLV offset is only used to read registers, while the offset used for
the FIFO addresses are hard coded in the driver and not given by the
TLV.
If we try to apply the TLV offset when reading the FIFOs, we'll read
from invalid addresses, causing the driver to hang.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 8d7dea25ad ("iwlwifi: dbg_ini: implement Rx fifos dump")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.fbab869c26fa.I4ddac20d02f9bce41855a816aa6855c89bc3874e@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cb377dfda1 upstream.
The AP may set the LDPC capability only in HE (IEEE80211_HE_PHY_CAP1),
but we were checking it only in the HT capabilities.
If we don't use this capability when required, the DSP gets the wrong
configuration in HE and doesn't work properly.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: befebbb30a ("iwlwifi: rs: consider LDPC capability in case of HE")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151128.492d167c1a25.I1ad1353dbbf6c99ae57814be750f41a1c9f7f4ac@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7937fd3227 upstream.
The code now compiles without ACPI, but there's a warning since
iwl_mvm_get_ppag_table() isn't used, and iwl_mvm_ppag_init() must
not unconditionally fail but return success instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
[Drop hunk removing iwl_mvm_get_ppag_table() since it doesn't exist in
5.4]
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a9149d243f upstream.
The logic for checking required NVM sections was recently fixed in
commit b3f20e0982 ("iwlwifi: mvm: fix NVM check for 3168
devices"). However, with that fixed the else is now taken for 3168
devices and within the else clause there is a mandatory check for the
PHY_SKU section. This causes the parsing to fail for 3168 devices.
The PHY_SKU section is really only mandatory for the IWL_NVM_EXT
layout (the phy_sku parameter of iwl_parse_nvm_data is only used when
the NVM type is IWL_NVM_EXT). So this changes the PHY_SKU section
check so that it's only mandatory for IWL_NVM_EXT.
Fixes: b3f20e0982 ("iwlwifi: mvm: fix NVM check for 3168 devices")
Signed-off-by: Dan Moulding <dmoulding@me.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 12d47f0ea5 ]
Fix a kernel panic by checking that the sta is not NULL.
This could happen during a reconfig flow, as mac80211 moves the sta
between all the states without really checking if the previous state was
successfully set. So, if for some reason we failed to add back the
station, subsequent calls to sta_state() callback will be done when the
station is NULL. This would result in a following panic:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000040
IP: iwl_mvm_cfg_he_sta+0xfc/0x690 [iwlmvm]
[..]
Call Trace:
iwl_mvm_mac_sta_state+0x629/0x6f0 [iwlmvm]
drv_sta_state+0xf4/0x950 [mac80211]
ieee80211_reconfig+0xa12/0x2180 [mac80211]
ieee80211_restart_work+0xbb/0xe0 [mac80211]
process_one_work+0x1e2/0x610
worker_thread+0x4d/0x3e0
[..]
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baa6cf8450 ]
Use a unique name when registering a thermal zone. Otherwise, with
multiple NICS, we hit the following warning during the unregistration.
WARNING: CPU: 2 PID: 3525 at fs/sysfs/group.c:255
RIP: 0010:sysfs_remove_group+0x80/0x90
Call Trace:
dpm_sysfs_remove+0x57/0x60
device_del+0x5a/0x350
? sscanf+0x4e/0x70
device_unregister+0x1a/0x60
hwmon_device_unregister+0x4a/0xa0
thermal_remove_hwmon_sysfs+0x175/0x1d0
thermal_zone_device_unregister+0x188/0x1e0
iwl_mvm_thermal_exit+0xe7/0x100 [iwlmvm]
iwl_op_mode_mvm_stop+0x27/0x180 [iwlmvm]
_iwl_op_mode_stop.isra.3+0x2b/0x50 [iwlwifi]
iwl_opmode_deregister+0x90/0xa0 [iwlwifi]
__exit_compat+0x10/0x2c7 [iwlmvm]
__x64_sys_delete_module+0x13f/0x270
do_syscall_64+0x5a/0x110
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f9a4e4a5 ]
The loop counter addr is a u16 where as the upper limit of the loop
is an int. In the unlikely event that the il->cfg->eeprom_size is
greater than 64K then we end up with an infinite loop since addr will
wrap around an never reach upper loop limit. Fix this by making addr
an int.
Addresses-Coverity: ("Infinite loop")
Fixes: be663ab670 ("iwlwifi: split the drivers for agn and legacy devices 3945/4965")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit cc4255eff5 upstream.
When a FTM request is aborted, the driver sends the abort command to
the fw and waits for a response. When the response arrives, the driver
calls cfg80211_pmsr_complete() for that request.
However, cfg80211 frees the requested data immediately after sending
the abort command, so this may lead to use after free.
Fix it by clearing the request data in the driver when the abort
command arrives and ignoring the fw notification that will come
afterwards.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Fixes: fc36ffda32 ("iwlwifi: mvm: support FTM initiator")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 197288d5ba upstream.
The IGTK keys are only removed by mac80211 after it has already
removed the AP station. This causes the driver to throw an error
because mac80211 is trying to remove the IGTK when the station doesn't
exist anymore.
The firmware is aware that the station has been removed and can deal
with it the next time we try to add an IGTK for a station, so we
shouldn't try to remove the key if the station ID is
IWL_MVM_INVALID_STA. Do this by removing the check for mvm_sta before
calling iwl_mvm_send_sta_igtk() and check return from that function
gracefully if the station ID is invalid.
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 990aba28f5 ]
The driver is required to stop the debug monitor HW recording regardless
of the debug configuration since the driver is responsible to halt the
FW DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2763bba632 ]
When receiving a new MCC driver get all the data about the new country
code and its regulatory information.
Mistakenly, we ignored the cap field, which includes global regulatory
information which should be applies to every channel.
Fix it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a89c72ffd0 ]
As noted in the previous commit, due to the way we allocate the
dev_cmd headers with 324 byte size, and 4/8 byte alignment, the
part we use of them (bytes 20..40-68) could still cross a page
and thus 2^32 boundary.
Address this by using alignment to ensure that the allocation
cannot cross a page boundary, on hardware that's affected. To
make that not cause more memory consumption, reduce the size of
the allocations to the necessary size - we go from 324 bytes in
each allocation to 60/68 on gen2 depending on family, and ~120
or so on gen1 (so on gen1 it's a pure reduction in size, since
we don't need alignment there).
To avoid size and clearing issues, add a new structure that's
just the header, and use kmem_cache_zalloc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit df2378ab0f upstream.
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b9f726c942 upstream.
It used to be the case that if we got here, we wouldn't warn
but instead allocate the queue (DQA). With using the mac80211
TXQs model this changed, and we really have nothing to do with
the frame here anymore, hence the warning now.
However, clearly we missed in coding & review that this is now
a pure error path and leaks the SKB if we return 0 instead of
an indication that the SKB needs to be freed. Fix this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d829229e35 upstream.
The purpose of this was to keep all the queues updated with
the Rx sequence numbers because unlikely yet possible
situations where queues can't understand if a specific
packet needs to be dropped or not.
Unfortunately, it was reported that this caused issues in
our DMA engine. We don't fully understand how this is related,
but this is being currently debugged. For now, just don't send
this notification to the Rx queues. This de-facto reverts my
commit 3c514bf831ac12356b695ff054bef641b9e99593:
iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues
This issue was reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=204873https://bugzilla.kernel.org/show_bug.cgi?id=205001
and others maybe.
Fixes: 3c514bf831 ("iwlwifi: mvm: add a loose synchronization of the NSSN across Rx queues")
CC: <stable@vger.kernel.org> # 5.3+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 205608749e upstream.
Since v5.4-rc1 was released, iwlwifi started throwing errors when scan
commands were sent to the firmware with certain devices (depending on
the OTP burned in the device, which contains the list of available
channels). For instance:
iwlwifi 0000:00:14.3: FW error in SYNC CMD SCAN_CFG_CMD
This bug was reported in the ArchLinux bug tracker:
https://bugs.archlinux.org/task/64703
And also in a specific case in bugzilla, when the lar_disabled option
was set: https://bugzilla.kernel.org/show_bug.cgi?id=205193
Revert the commit that introduced this error, by using the number of
channels from the OTP instead of the number of channels that is
specified in the FW TLV that tells us how many channels it supports.
This reverts commit 06eb547c4a.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Mehmet Akif Tasova <makiftasova@gmail.com>
[ Luca: reworded the commit message a bit. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c80794323e ]
Commit 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL
skbs") introduces batching of GRO_NORMAL packets in napi_frags_finish,
and commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") adds the same to napi_skb_finish. However,
dev_gro_receive (that is called just before napi_{frags,skb}_finish) can
also pass skbs to the networking stack: e.g., when the GRO session is
flushed, napi_gro_complete is called, which passes pp directly to
netif_receive_skb_internal, skipping napi->rx_list. It means that the
packet stored in pp will be handled by the stack earlier than the
packets that arrived before, but are still waiting in napi->rx_list. It
leads to TCP reorderings that can be observed in the TCPOFOQueue counter
in netstat.
This commit fixes the reordering issue by making napi_gro_complete also
use napi->rx_list, so that all packets going through GRO will keep their
order. In order to keep napi_gro_flush working properly, gro_normal_list
calls are moved after the flush to clear napi->rx_list.
iwlwifi calls napi_gro_flush directly and does the same thing that is
done by gro_normal_list, so the same change is applied there:
napi_gro_flush is moved to be before the flush of napi->rx_list.
A few other drivers also use napi_gro_flush (brocade/bna/bnad.c,
cortina/gemini.c, hisilicon/hns3/hns3_enet.c). The first two also use
napi_complete_done afterwards, which performs the gro_normal_list flush,
so they are fine. The latter calls napi_gro_receive right after
napi_gro_flush, so it can end up with non-empty napi->rx_list anyway.
Fixes: 323ebb61e3 ("net: use listified RX for handling GRO_NORMAL skbs")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Cc: Alexander Lobakin <alobakin@dlink.ru>
Cc: Edward Cree <ecree@solarflare.com>
Acked-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb99ff9baa upstream.
When the single antenna diversity support was sent upstream, only some
definitions were sent, due to a bad revert.
Fix this by adding the actual code.
Fixes: 5952e0ec3f ("iwlwifi: mvm: add support for single antenna diversity")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee4cce9b9d upstream.
debugfs amsdu_len sets only the max_amsdu_len for ieee80211 station
so take it into consideration while getting max amsdu
Fixes: af2984e9e6 ("iwlwifi: mvm: add a debugfs entry to set a fixed size AMSDU for all TX packets")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db5cce1afc upstream.
This reverts commit 968dcfb490.
Both that commit and commit 809805a820
attempted to fix the same bug (dead assignments to the local variable
cfg), but they did so in incompatible ways. When they were both merged,
independently of each other, the combination actually caused the bug to
reappear, leading to a firmware crash on boot for some cards.
https://bugzilla.kernel.org/show_bug.cgi?id=205719
Signed-off-by: Anders Kaseorg <andersk@mit.edu>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0df36b90c4 upstream.
We need to reset the NIC after setting the bits to enable power
gating and that cannot be done too late in the flow otherwise it
cleans other registers and things that were already configured,
causing initialization to fail.
In order to fix this, move the function to the common code in trans.c
so it can be called directly from there at an earlier point, just
after the reset we already do during initialization.
Fixes: 9a47cb9883 ("iwlwifi: pcie: add workaround for power gating in integrated 22000")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205719
Cc: stable@ver.kernel.org # 5.4+
Reported-by: Anders Kaseorg <andersk@mit.edu>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b167191e2a ]
Commit 6570bc79c0 ("net: core: use listified Rx for GRO_NORMAL in
napi_gro_receive()") has applied batched GRO_NORMAL packets processing
to all napi_gro_receive() users, including mac80211-based drivers.
However, this change has led to a regression in iwlwifi driver [1][2] as
it is required for NAPI users to call napi_complete_done() or
napi_complete() and the end of every polling iteration, whilst iwlwifi
doesn't use NAPI scheduling at all and just calls napi_gro_flush().
In that particular case, packets which have not been already flushed
from napi->rx_list stall in it until at least next Rx cycle.
Fix this by adding a manual flushing of the list to iwlwifi driver right
before napi_gro_flush() call to mimic napi_complete() logics.
I prefer to open-code gro_normal_list() rather than exporting it for 2
reasons:
* to prevent from using it and napi_gro_flush() in any new drivers,
as it is the *really* bad way to use NAPI that should be avoided;
* to keep gro_normal_list() static and don't lose any CC optimizations.
I also don't add the "Fixes:" tag as the mentioned commit was only a
trigger that only exposed an improper usage of NAPI in this particular
driver.
[1] https://lore.kernel.org/netdev/PSXP216MB04388962C411CD0B17A86F47804A0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
[2] https://bugzilla.kernel.org/show_bug.cgi?id=205647
Signed-off-by: Alexander Lobakin <alobakin@dlink.ru>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Reported-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Tested-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Reviewed-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5aaa8be29 ]
This is present since the introduction of iwlmvm.
Example stack trace on MIPS:
[<ffffffffc0789328>] iwl_mvm_rx_rx_mpdu+0xa8/0xb88 [iwlmvm]
[<ffffffffc0632b40>] iwl_pcie_rx_handle+0x420/0xc48 [iwlwifi]
Tested with a Wireless AC 7265 for ~6 months, confirmed to fix the
problem. No other unaligned accesses are spotted yet.
Signed-off-by: Wang Xuerui <wangxuerui@qiniu.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4f4925a7b2 upstream.
When the implementation of SKBs with fraglist was sent upstream, a
merge-damage occurred and half the patch was not applied.
This causes problems in high-throughput situations with AX200 devices,
including low throughput and FW crashes.
Introduce the part that was missing from the original patch.
Fixes: 0044f1716c ("iwlwifi: pcie: support transmitting SKBs with fraglist")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ This patch was created by me, but the original author of this code
is Johannes, so his s-o-b is here and he's marked as the author of
the patch. ]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
From gen2 PN is totally offloaded to hardware (also the space for the
IV isn't part of the skb). As you can see in mvm/mac80211.c:3545, the
MAC for cipher types CCMP/GCMP doesn't set
IEEE80211_KEY_FLAG_PUT_IV_SPACE for gen2 NICs.
This causes all the AMSDU data to be corrupted with cipher enabled.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The API was reduced to include only knowledge currently needed by the
FW scan logic, the rest is legacy. Support the new, reduced version.
Using the old API with newer firmwares (starting from
iwlwifi-*-50.ucode, which implements and requires the new API version)
causes an assertion failure similar to this one:
[ 2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When converting the wrong qu configurations in an earlier commit, I
accidentally swapped 0x2720 and 0x30DC. Instead of converting 0x2720,
I converted 0x30DC. Undo 0x30DC and convert 0x2720.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Johannes Berg