commit 74a8c816fa upstream.
This code does not ensure that the whole buffer is initialized and none
of the callers check for errors so potentially none of the buffer is
initialized. Add a memset to eliminate this bug.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X8ilOfVz3pf0T5ec@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86279456a4 ]
Free the skb if usb_submit_urb fails on rx_urb. And free the urb
no matter usb_submit_urb succeeds or not in rtl8xxxu_submit_int_urb.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906040424.22022-1-chiu@endlessm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee755732b7 ]
The vht capability of MAX_MPDU_LENGTH is 11454 in rtw88; however, the rx
buffer size for each packet is 8192. When receiving packets that are
larger than rx buffer size, it will leads to rx buffer ring overflow.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-2-tehuang@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03128643eb ]
If usb_submit_urb fails the allocated urb should be unanchored and
released.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200622132113.14508-3-code@reto-schneider.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f194bd4ca ]
The coex mechanism used to skip upon the freeze flag is raised.
That will cause the coex mechanism being skipped unexpectedly.
Coex only wanted to keep the TDMA table from being changed by
BT side.
So, check the freeze and reason, if the coex reason is coming
from BT info, skip it, to make sure the coex triggered by Wifi
itself can work.
This is required for the AP mode, while the control flow is
different with STA mode. When starting an AP mode, the AP mode
needs to start working immedaitely after leaving IPS, and the
freeze flag could be raised. If the coex info is skipped, then
the AP mode will not set the antenna owner, leads to TX stuck.
Fixes: 4136214f7c ("rtw88: add BT co-existence support")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-5-yhchuang@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4dd86b901d ]
Fix the transmission is not sent with short GI under
some conditions even if the receiver supports short GI.
If VHT capability IE exists in the beacon, the original
code uses the short GI for 80M field as driver's short GI
setting for transmission, even the current bandwidth is
not 80MHz.
Short GI supported fields for 20M/40M are informed in HT
capability information element, and short GI supported
field for 80M is informed in VHT capability information
element.
These three fields may be set to different values.
Driver needs to record each short GI support field for
each bandwidth, and send correct info depends on current
bandwidth to the WiFi firmware.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-3-yhchuang@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae44fa993e ]
Convert the type of LDPC field to boolen because
LDPC field of RA info H2C command to firmware
is only one bit.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-2-yhchuang@realtek.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit beb12813bc ]
Seven years ago we tried to fix a leak but actually introduced a double
free instead. It was an understandable mistake because the code was a
bit confusing and the free was done in the wrong place. The "skb"
pointer is freed in both _rtl_usb_tx_urb_setup() and _rtl_usb_transmit().
The free belongs _rtl_usb_transmit() instead of _rtl_usb_tx_urb_setup()
and I've cleaned the code up a bit to hopefully make it more clear.
Fixes: 36ef0b473f ("rtlwifi: usb: add missing freeing of skbuff")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200513093951.GD347693@mwanda
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 191f6b08bf ]
the related system resources were not released when pci_iomap() return
error in the rtw_pci_io_mapping() function. add pci_release_regions() to
fix it.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504083442.3033-1-zhengdejin5@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6cb5f3ea46 upstream.
When fixing the initialization race, we neglected to account for
the fact that debugfs is initialized in wiphy_register(), and
some debugfs things went missing (or rather were rerooted to the
global debugfs root).
Fix this by adding debugfs entries only after wiphy_register().
This requires some changes in the rate control code since it
currently adds debugfs at alloc time, which can no longer be
done after the reordering.
Reported-by: Jouni Malinen <j@w1.fi>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Felix Fietkau <nbd@nbd.name>
Cc: stable@vger.kernel.org
Fixes: 52e04b4ce5 ("mac80211: fix race in ieee80211_register_hw()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Link: https://lore.kernel.org/r/20200423111344.0e00d3346f12.Iadc76a03a55093d94391fc672e996a458702875d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c80b18cbb0 upstream.
For some unexplained reason, commit d1d1a96bdb ("rtlwifi: rtl8188ee:
Remove local configuration variable") broke at least one system. As
the only net effect of the change was to remove 2 bytes from the start
of struct phy_status_rpt, this patch adds 2 bytes of padding at the
beginning of the struct.
Fixes: d1d1a96bdb ("rtlwifi: rtl8188ee: Remove local configuration variable")
Cc: Stable <stable@vger.kernel.org> # V5.4+
Reported-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Tested-by: Ashish <ashishkumar.yadav@students.iiserpune.ac.in>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f4f84ff837 ]
Sometimes the TX queue may be empty and we could possible
dequeue a NULL pointer, crash the kernel. If the skb is NULL
then there is nothing to do, just leave the ISR.
And the TX queue should not be empty here, so print an error
to see if there is anything wrong for DMA ring.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a68fa5f9 ]
The rate mask is used to tell firmware the supported rate depends on
negotiation. We loop 2 times for all VHT/HT 2SS rate mask first, and then
only keep the part according to chip's NSS.
This commit fixes the logic error of '&' operations for VHT/HT rate, and
we should run this logic before adding legacy rate.
To access HT MCS map, index 0/1 represent MCS 0-7/8-15 respectively. Use
NL80211_BAND_xxx is incorrect, so fix it as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 39a4281c31 upstream.
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Cc: stable <stable@vger.kernel.org> # 4.4
Cc: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4268729eb upstream.
Disable efuse if the efuse is enabled when we failed to setup the efuse
information, otherwise the hardware will not turn off.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3594559f4 upstream.
When downloading the reserved page, the first page always contains
a beacon for the firmware to reference. For non-beaconing modes such
as station mode, also put a blank skb with length=1.
And for the beaconing modes, driver will get a real beacon with a
length approximate to the page size. But as the beacon is always put
at the first page, it does not need a tx_desc, because the TX path
will generate one when TXing the reserved page to the hardware. So we
could allocate a buffer with a size smaller than the reserved page,
when using memcpy() to copy the content of reserved page to the buffer,
the over-sized reserved page will violate the kernel memory.
To fix it, add the tx_desc before memcpy() the reserved packets to
the buffer, then we can get SKBs with correct length when counting
the pages in total. And for page 0, count the extra tx_desc_sz that
the TX path will generate. This way, the first beacon that allocated
without tx_desc can be counted with the extra tx_desc_sz to get
actual pages it requires.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18a0696e85 upstream.
The level of cckpd is from 0 to 4, and it is the index of
array pd_lvl[] and cs_lvl[]. However, the length of both arrays
are 4, which is smaller than the possible maximum input index.
Enumerate cck level to make sure the max level will not be wrong
if new level is added in future.
Fixes: 479c4ee931 ("rtw88: add dynamic cck pd mechanism")
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 091c6e9c08 upstream.
When building with Clang + -Wtautological-pointer-compare:
drivers/net/wireless/realtek/rtlwifi/regd.c:389:33: warning: comparison
of address of 'rtlpriv->regd' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (wiphy == NULL || &rtlpriv->regd == NULL)
~~~~~~~~~^~~~ ~~~~
1 warning generated.
The address of an array member is never NULL unless it is the first
struct member so remove the unnecessary check. This was addressed in
the staging version of the driver in commit f986978b32 ("Staging:
rtlwifi: remove unnecessary NULL check").
While we are here, fix the following checkpatch warning:
CHECK: Comparison to NULL could be written "!wiphy"
35: FILE: drivers/net/wireless/realtek/rtlwifi/regd.c:389:
+ if (wiphy == NULL)
Fixes: 0c8173385e ("rtl8192ce: Add new driver")
Link:https://github.com/ClangBuiltLinux/linux/issues/750
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a2cdd07488 upstream.
In rtl8xxxu_submit_int_urb if usb_submit_urb fails the allocated urb
should be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5174f1e410 ]
This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with
Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a
single memory leak during probe:
unreferenced object 0xec13ee40 (size 176):
comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164
[<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common]
[<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu]
[<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi]
[<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211]
[<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211]
[<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211]
[<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211]
[<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211]
[<ac5fcae4>] process_one_work+0x22c/0x564
[<f5e6d3b6>] worker_thread+0x44/0x5d8
[<82c7b073>] kthread+0x150/0x154
[<b43e1b7d>] ret_from_fork+0x14/0x2c
[<794dff30>] 0x0
It is because 8192cu doesn't implement usb_cmd_send_packet(), and this
patch just frees the skb within the function to resolve memleak problem
by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download
command packet for firmware via the function, applying this patch doesn't
affect driver behavior.
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0eeb91ade9 ]
The RTL8723BU has problems connecting to AP after each warm reboot.
Sometimes it returns no scan result, and in most cases, it fails
the authentication for unknown reason. However, it works totally
fine after cold reboot.
Compare the value of register SYS_CR and SYS_CLK_MAC_CLK_ENABLE
for cold reboot and warm reboot, the registers imply that the MAC
is already powered and thus some procedures are skipped during
driver initialization. Double checked the vendor driver, it reads
the SYS_CR and SYS_CLK_MAC_CLK_ENABLE also but doesn't skip any
during initialization based on them. This commit only tells the
RTL8723BU to do full initialization without checking MAC status.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12078aae45 ]
With shallow buffer size, certain BT devices have active
A2DP flow control to fill buffer frequently. If the slot
is not at BT side, data can't be sent successfully to BT
devices, and will cause audio glitch.
To resolve this issue, this commit splits TUs into 4-slots
instead of 2-slot for all of the A2DP related coexistence
strategies. That makes BT have higher opportunity to fill
the A2DP buffer in time, and the audio quality could be
more stable and smooth.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4f5bb7ff8b ]
8822C is a 2x2 11ac chip, and then NSS must be less or equal to 2. However,
current nss of hw cap is 3, likes
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=3
This commit adds constraint to make sure NSS <= rf_path_num, and result
looks like
hw cap: hci=0x0f, bw=0x07, ptcl=0x03, ant_num=7, nss=2
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3f93616951 ]
In rtl_usb_probe if allocation for usb_data fails the allocated hw
should be released. In addition the allocated rtlpriv->usb_data should
be released on error handling path.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 330bb71171 upstream.
In commit 38506ecefa ("rtlwifi: rtl_pci: Start modification for
new drivers"), the flag that indicates that interrupts are enabled was
never set.
In addition, there are several places when enable/disable interrupts
were commented out are restored. A sychronize_interrupts() call is
removed.
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3155db7613 upstream.
In commit 38506ecefa ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback needed to check if the hardware has released
a buffer indicating that a DMA operation is completed was not added.
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0e531cc575 upstream.
In commit 38506ecefa ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback to get the RX buffer address was added to
the PCI driver. Unfortunately, driver rtl8192de was not modified
appropriately and the code runs into a WARN_ONCE() call. The use
of an incorrect array is also fixed.
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8020919a9b ("mac80211: Properly handle SKB with radiotap
only"), buffers whose length is too short cause a WARN_ON(1) to be
executed. This change exposed a fault in rtlwifi drivers, which is fixed
by regarding packets with skb->len <= FCS_LEN as though they are in error
and dropping them. The test is now annotated as likely.
Cc: Stable <stable@vger.kernel.org> # v5.0+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Nicolas Waisman noticed that even though noa_len is checked for
a compatible length it's still possible to overrun the buffers
of p2pinfo since there's no check on the upper bound of noa_num.
Bound noa_num against P2P_MAX_NOA_NUM.
Reported-by: Nicolas Waisman <nico@semmle.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After firmware has been downloaded, driver should send
some information to it through H2C commands. Those H2C
commands are transmitted through TX path.
But before HCI has been started, the TX path is not
working completely. Such as PCI interfaces, the interrupts
are not enabled, hence TX interrupts will not be issued
after H2C skb has been DMAed to the device. And the H2C
skbs will not be released until the device is powered off.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Interrupt is disabled to stop PCI, which means the skbs
queued for each TX ring will not be released via DMA
interrupt. To avoid those skbs remained being left in
the skb queue until PCI has been removed, driver needs
to release skbs by itself.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These skbs free routines could be used when driver wants
to stop PCI bus, because some of the skbs remained in the
queue may not have been returned via DMA interrupt.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report chains and chain_signal in ieee80211_rx_status.
It is useful for program such as tcpdump to see if the
antennas are well connected/placed.
8822C is able to receive CCK rates with 2 antennas, while
8822B can only use 1 antenna path to receive CCK rates.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix the wrong RF path for CCK rx power calculation.
Fixes: e3037485c6 ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92d_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92d_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Function _rtl92c_evm_db_to_percentage is functionally identical
to the generic version rtl_evm_db_to_percentage, so remove
_rtl92c_evm_db_to_percentage and use the generic version instead.
Signed-off-by: Michael Straube <straube.linux@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hardware has enough buffer to receive like 8K for an MPDU.
So tell mac80211 that we can receive AMSDU in AMPDU.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This mechanism reduces the numbers of false alram in cck rate by
dynamically adjusting the value of power threshold and cs_ratio.
We determine the new value by three factors, which are rssi, false alarm
count and igi. Based on these factors, we define the current condition
into five levels. Compared to the previous level, if the level is changed,
we set the new values for power threshold and cs_ratio.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 8822c requires to do not only IQK, but also DPK.
Move these calibrations that need to be done once the channel
is determined, into phy_calibration.
And note that the order of the calibrations matters, 8822c
should do IQK first, then DPK.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power amplifiers are not linear components, and require DPK to
reduce its nonlinearity. DPK is called Digital Pre-distortion
Calibration, can be used to compensate the output of power.
DPK tracking is in charge of tracking the thermal changes. And
it then shifts the power curve accordingly, which makes the
power output remains linear even if the PA works in different
temperature.
To perform DPK, the parameter table should also be updated.
And the table will be applied when device is powered on.
Then DPK will reference the values to calibrate.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for doing IQK in firmware
Ideally the RF component's I/Q vectors should be orthogonal,
but usually they are not. So we need to calibrate for the RF
components, ex. PA/LNA, ADC/DAC.
And if the I/Q vectors are more orthogonal, the mixed signal
will have less deviation. This helps with those rates with
higher modulation (MCS8-9), because they have more strict
EVM/SNR requirement. Also the better of the quality of the
signal, the longer it can propagate, and the better throughput
performance we can get.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable 8822C Tx/Rx interrupt migration.
In some platforms, performance test may cause heavy cpu loading and get
bad results. Interrupt migration can decrease the amount of interrupts,
and lower cpu loading.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
update sequence to v13 to reduce power consumption
when MAC power off
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Each of these drivers defines some device to host macros that are never
used, thus they can be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter