[ Upstream commit 44a0a3c179 ]
The related system resources were not released when pci_set_dma_mask(),
pci_set_consistent_dma_mask(), or pci_iomap() return error in the
amd_ntb_init_pci() function. Add pci_release_regions() to fix it.
Fixes: a1b3695820 ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Kaige Li <likaige@loongson.cn>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34d8673a01 ]
When running ntb_test, the script tries to run the ntb_perf test
immediately after probing the modules. Since adding multi-port support,
this fails seeing the new initialization procedure in ntb_perf
can not complete instantly.
To fix this we add a completion which is waited on when a test is
started. In this way, run can be written any time after the module is
loaded and it will wait for the initialization to complete instead of
sending an error.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b54369a248 ]
Legacy drivers do not have port numbers (but is reliably only two ports)
and was broken by the recent commit that added mult-port support to
ntb_perf. This is especially important to support the cross link
topology which is perfectly symmetric and cannot assign unique port
numbers easily.
Hardware that returns zero for both the local port and the peer should
just always use gidx=0 for the only peer.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9c4211ac9 ]
ntb_perf should not require more than one memory window per peer. This
was probably an off-by-one error.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 40da7d9a93 ]
Commit 417cf39cfe ("NTB: Set dma mask and dma coherent mask to NTB
devices") started using the NTB device for DMA allocations which was
turns out was wrong. If the IOMMU is enabled, such alloctanions will
always fail with messages such as:
DMAR: Allocating domain for 0000:02:00.1 failed
This is because the IOMMU has not setup the device for such use.
Change the tools back to using the PCI device for allocations seeing
it doesn't make sense to add an IOMMU group for the non-physical NTB
device. Also remove the code that sets the DMA mask as it no longer
makes sense to do this.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 912e12813d ]
When running ntb_test this warning is issued:
./ntb_test.sh: line 200: warning: command substitution: ignored null
byte in input
This is caused by the kernel returning one more byte than is necessary
when reading the link file.
Reduce the number of bytes read back to 2 as it was before the
commit that regressed this.
Fixes: 7f46c8b3a5 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 433efe7206 ]
Currently, ntb->dev is passed to dma_alloc_coherent
and dma_free_coherent calls. The returned dma_addr_t
is the CPU physical address. This works fine as long
as IOMMU is disabled. But when IOMMU is enabled, we
need to make sure that IOVA is returned for dma_addr_t.
So the correct way to achieve this is by changing the
first parameter of dma_alloc_coherent() as ntb->pdev->dev
instead.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 98f4e14026 ]
Currently, ntb->dev is passed to dma_alloc_coherent
and dma_free_coherent calls. The returned dma_addr_t
is the CPU physical address. This works fine as long
as IOMMU is disabled. But when IOMMU is enabled, we
need to make sure that IOVA is returned for dma_addr_t.
So the correct way to achieve this is by changing the
first parameter of dma_alloc_coherent() as ntb->pdev->dev
instead.
Fixes: 5648e56d03 ("NTB: ntb_perf: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fc8b086d9d ]
When the commit adding ntb_default_port_number() and
ntb_default_peer_port_number() entered the kernel there was no
users of it so it was impossible to tell what the API needed.
When a user finally landed a year later (ntb_pingpong) there were
more NTB topologies were created and no consideration was considered
to how other drivers had changed.
Now that there is a user it can be fixed to provide a sensible default
for the legacy drivers that do not implement ntb_{peer_}port_number().
Seeing ntb_pingpong doesn't check error codes returning EINVAL was also
not sensible.
Patches for ntb_pingpong and ntb_perf follow (which are broken
otherwise) to support hardware that doesn't have port numbers. This is
important not only to not break support with existing drivers but for
the cross link topology which, due to its perfect symmetry, cannot
assign unique port numbers to each side.
Fixes: 1e5301196a ("NTB: Add indexed ports NTB API")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ca93c45755 ]
This commit fixes pingpong support for existing drivers that do not
implement ntb_default_port_number() and ntb_default_peer_port_number().
This is required for hardware (like the crosslink topology of
switchtec) which cannot assign reasonable port numbers to each port due
to its perfect symmetry.
Instead of picking the doorbell to use based on the the index of the
peer, we use the peer's port number. This is a bit clearer and easier
to understand.
Fixes: c7aeb0afdc ("NTB: ntb_pp: Add full multi-port NTB API support")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Tested-by: Alexander Fomichev <fomichev.ru@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Sasha Levin <sashal@kernel.org>
The AMD new hardware uses BAR23 and BAR45 as memory windows
as compared to previos where BAR1, BAR23 and BAR45 is used
for memory windows.
This patch add support for both AMD hardwares.
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Variable rc is initialized to a value that is never read and it
is re-assigned later. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On switchtec_ntb_mw_set_trans() call, when (only) address == 0, it acts as
ntb_mw_clear_trans(). Fix this, since address == 0 and size != 0 is valid
combination for setting translation.
Signed-off-by: Alexander Fomichev <fomichev.ru@gmail.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
second parameter of ntb_peer_mw_get_addr is pointing to wrong memory
window index by passing "peer gidx" instead of "local gidx".
For ex, "local gidx" value is '0' and "peer gidx" value is '1', then
on peer side ntb_mw_set_trans() api is used as below with gidx pointing to
local side gidx which is '0', so memroy window '0' is chosen and XLAT '0'
will be programmed by peer side.
ntb_mw_set_trans(perf->ntb, peer->pidx, peer->gidx, peer->inbuf_xlat,
peer->inbuf_size);
Now, on local side ntb_peer_mw_get_addr() is been used as below with gidx
pointing to "peer gidx" which is '1', so pointing to memory window '1'
instead of memory window '0'.
ntb_peer_mw_get_addr(perf->ntb, peer->gidx, &phys_addr,
&peer->outbuf_size);
So this patch pass "local gidx" as parameter to ntb_peer_mw_get_addr().
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
to test and use this feature in the NTB transport layer. Also, bug
fixes for the AMD and Switchtec drivers, as well as some general
patches.
-----BEGIN PGP SIGNATURE-----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=P1lR
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Introduce the module parameter 'use_msi' which, when set, uses
MSI interrupts instead of doorbells for each queue pair (QP). The
parameter is only available if NTB MSI support is configured into
the kernel. We also require there to be more than one memory window
(MW) so that an extra one is available to forward the APIC region.
To use MSIs, we request one interrupt per QP and forward the MSI address
and data to the peer using scratch pad registers (SPADS) above the MW
SPADS. (If there are not enough SPADS the MSI interrupt will not be used.)
Once registered, we simply use ntb_msi_peer_trigger and the receiving
ISR simply queues up the rxc_db_work for the queue.
This addition can significantly improve performance of ntb_transport.
In a simple, untuned, apples-to-apples comparision using ntb_netdev
and iperf with switchtec hardware, I see 3.88Gb/s without MSI
interrupts and 14.1Gb/s wit MSI, which is a more than 3x improvement.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Introduce a tool to test NTB MSI interrupts similar to the other
NTB test tools. This tool creates a debugfs directory for each
NTB device with the following files:
port
irqX_occurrences
peerX/port
peerX/count
peerX/trigger
The 'port' file tells the user the local port number and the
'occurrences' files tell the number of local interrupts that
have been received for each interrupt.
For each peer, the 'port' file and the 'count' file tell you the
peer's port number and number of interrupts respectively. Writing
the interrupt number to the 'trigger' file triggers the interrupt
handler for the peer which should increment their corresponding
'occurrences' file. The 'ready' file indicates if a peer is ready,
writing to this file blocks until it is ready.
The module parameter num_irqs can be used to set the number of
local interrupts. By default this is 4. This is only limited by
the number of unused MSI interrupts registered by the hardware
(this will require support of the hardware driver) and there must
be at least 2*num_irqs + 1 spads registers available.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The NTB MSI library allows passing MSI interrupts across a memory
window. This offers similar functionality to doorbells or messages
except will often have much better latency and the client can
potentially use significantly more remote interrupts than typical hardware
provides for doorbells. (Which can be important in high-multiport
setups.)
The library utilizes one memory window per peer and uses the highest
index memory windows. Before any ntb_msi function may be used, the user
must call ntb_msi_init(). It may then setup and tear down the memory
windows when the link state changes using ntb_msi_setup_mws() and
ntb_msi_clear_mws().
The peer which receives the interrupt must call ntb_msim_request_irq()
to assign the interrupt handler (this function is functionally
similar to devm_request_irq()) and the returned descriptor must be
transferred to the peer which can use it to trigger the interrupt.
The triggering peer, once having received the descriptor, can
trigger the interrupt by calling ntb_msi_peer_trigger().
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The kbuild system does not support having multiple source files in
a module if one of those source files has the same name as the module.
Therefore, we must rename ntb.c to core.c, while the module remains
ntb.ko.
This is similar to the way the nvme modules are structured.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec does not support setting multiple MWs simultaneously. The
driver takes a hardware lock to ensure that two peers are not doing this
simultaneously and it fails if someone else takes the lock. In most
cases, this is fine as clients only setup the MWs once on one side of
the link.
However, there's a race condition when a re-initialization is caused by
a link event. The driver will re-setup the shared memory window
asynchronously and this races with the client setting up it's memory
windows on the link up event.
To fix this we ensure do the entire initialization in a work queue and
signal the client once it's done.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In case of NTB crosslink topology, the setting of shared memory window in
the virtual partition doesn't reset on peer's reboot. So skip the
unnecessary re-setup of shared memory window for that case.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When a re-initialization is caused by a link event, the driver will
re-setup the shared memory window. But at that time, the shared memory
is still valid, and it's unnecessary to free, reallocate and then
initialize it again. We only need to reconfigure the hardware
registers. Remove the redundant steps from
switchtec_ntb_reinit_peer() function.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This code triggers a Smatch warning:
drivers/ntb/hw/amd/ntb_hw_amd.c:336 amd_ntb_db_vector_mask()
warn: should '(1 << db_vector)' be a 64 bit type?
I don't think "db_vector" can be higher than 16 so this doesn't affect
runtime, but it's nice to silence the static checker warning and we
might increase "ndev->db_count" in the future.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This code triggers a Smatch warning:
drivers/ntb/hw/mscc/ntb_hw_switchtec.c:884 switchtec_ntb_init_sndev()
warn: should '(1 << sndev->peer_partition)' be a 64 bit type?
The "part_map" and "tpart_vec" variables are u64 type so this seems like
a valid warning.
Fixes: 3df54c870f ("ntb_hw_switchtec: Allow using Switchtec NTB in multi-partition setups")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Dan Carpenter's static checker reported:
drivers/ntb/ntb_transport.c:1926 ntb_transport_create_queue()
error: we previously assumed 'qp->tx_dma_chan' could be null (see line 1872)
This is because the tx_mw_dma_addr is uninitialized in this function and
may be incorrectly released using a NULL DMA channel.
In practice this bug will not likely be seen. I'd guess you could hit
this if you loaded ntb_netdev with use_dma=True, then unloaded it and
loaded it again after setting the module parameter to use_dma=False.
To fix this, we simply ensure that tx_mw_dma_addr is always
initialized to zero. This is the safest in case any other part of the
code operates on it if it is non-zero.
Fixes: c59666bb32 ("NTB: ntb_transport: Ensure the destination buffer is mapped for TX DMA")
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
As per amd ntb spec it says that peer limit register
must be programmed
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
when ntb_perf is unloaded, the command scratchpad register still
retains the last initialized value of PERF_CMD_INVAL. When ntb_perf
is re-loaded and reads peer command scratchpad register and it mis
interprets the peer state as initialized.
To avoid this, clearing the local side command scratchpad register
in perf_disable_service
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If ntb link disabled before clearing peer's XLAT register, the clearing
won't have any effect since the link is already down. So modified the
sequence so that the link is down only towards the end of the function
after clearing the XLAT register
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
while waiting for the peer ntb_perf to initialize scratchpad
registers, local side ntb_perf might have already exhausted the
maximum number of retries which is currently set to 500. To avoid
this and to give little more time to the peer ntb_perf for scratchpad
initialization, increased the number of retries to 1000
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fix sparse warning:
drivers/ntb/hw/intel/ntb_hw_gen3.c:535:5: warning:
symbol 'intel_ntb3_peer_db_addr' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
transport improvements, and a reworking of the peer_db_addr to all for
better abstraction
-----BEGIN PGP SIGNATURE-----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=7EC8
-----END PGP SIGNATURE-----
Merge tag 'ntb-5.1' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
- fixes for switchtec debugability and mapping table entries
- NTB transport improvements
- a reworking of the peer_db_addr for better abstraction
* tag 'ntb-5.1' of git://github.com/jonmason/ntb:
NTB: add new parameter to peer_db_addr() db_bit and db_data
NTB: ntb_transport: Ensure the destination buffer is mapped for TX DMA
NTB: ntb_transport: Free MWs in ntb_transport_link_cleanup()
ntb_hw_switchtec: Added support of >=4G memory windows
ntb_hw_switchtec: NT req id mapping table register entry number should be 512
ntb_hw_switchtec: debug print 64bit aligned crosslink BAR Numbers
NTB door bell usage depends on NTB hardware.
ex: intel NTB gen1 has one peer door bell register which can be controlled
by the bitmap writen to it, while Intel NTB gen3 has a registers
per door bell and the data trigering the each door bell is always 1.
therefore exposing only peer door bell address forcing the user
to be aware of such low level details
Signed-off-by: Leonid Ravich <Leonid.Ravich@emc.com>
Acked-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <allenbh@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Presently, when ntb_transport is used with DMA and the IOMMU turned on,
it fails with errors from the IOMMU such as:
DMAR: DRHD: handling fault status reg 202
DMAR: [DMA Write] Request device [00:04.0] fault addr
381fc0340000 [fault reason 05] PTE Write access is not set
This is because ntb_transport does not map the BAR space with the IOMMU.
To fix this, we map the entire MW region for each QP after we assign
the DMA channel. This prevents needing an extra DMA map in the fast
path.
Link: https://lore.kernel.org/linux-pci/499934e7-3734-1aee-37dd-b42a5d2a2608@intel.com/
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If NTB peer host crashes or reboots, the NTB transport link will be
down and the MWs of NTB transport will be invalid. But the
ntb_transport_link_cleanup() does not free these invalid MWs. When
the NTB peer host is recovered later, NTB transport link will be
up and the ntb_set_mw() will not reset up MWs. Because the MWs of
NTB transport are invalid, the NTB transport will not work.
We can fix it by freeing MWs when NTB transport link is down, then
the ntb_set_mw() will reset up MWs when NTB transport link is up.
Signed-off-by: Joey Zhang <joey.zhang@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Current Switchtec's BAR setup registers are limited to 32bits,
corresponding to the maximum MW (memory window) size is <4G.
Increase the MW sizes with the addition of the BAR Setup Extension
Register for the upper 32bits of a 64bits MW size. This increases the MW
range to between 4K and 2^63.
Reported-by: Boris Glimcher <boris.glimcher@emc.com>
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Switchtec NTB crosslink BARs are 64bit addressed but they are printed as
32bit addressed BARs. Fix debug log to increment the BAR numbers by 2 to
reflect the 64bit address alignment.
Fixes: 0175250182 ("ntb_hw_switchtec: Add initialization code for crosslink")
Signed-off-by: Paul Selles <paul.selles@microchip.com>
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Clean up the ifdefs which conditionally defined the io{read|write}64
functions in favour of the new common io-64-nonatomic-lo-hi header.
Per a nit from Andy Shevchenko, the include list is also made
alphabetical.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that ioread64 and iowrite64 are available in io-64-nonatomic,
we can remove the hack at the top of ntb_hw_intel.c and replace it
with an include.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since IDT PCIe-switch temperature sensor is now always available
irregardless of the EEPROM/BIOS settings, Kconfig and in-code
description should be properly altered. In addition lets update
the driver copyright lines.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT PCIe-switch temperature sensor interface is very broken. First
of all only a few combinations of TMPCTL threshold enable bits
really cause the interrupts unmasked. Even if an individual bit
indicates the event unmasked, corresponding IRQ just isn't generated.
Most of the threshold enable bits combinations are in fact useless and
non of them can help to create a fully functional alarm interface.
So to speak, we can't create a well defined hwmon alarms based on
the IDT PCI-switch threshold IRQs.
Secondly a single threshold IRQ (not a combination of thresholds) can
be successfully enabled without the issue described above. But in this
case we experienced an enormous number of interrupts generated by
the chip if the temperature got near the enabled threshold value. Filter
adjustment didn't help much. It also doesn't provide a hysteresis settings.
Due to the temperature sample fluctuations near the threshold the
interrupts spate makes the system nearly unusable until the temperature
value finally settled so being pushed either to be fully higher or lower
the threshold.
All of these issues makes the temperature sensor alarm interface useless
and even at some point dangerous to be used in the driver. In this case
it is safer to completely discard it and disable the temperature alarm
interrupts.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT PCIe switches provide an embedded temperature sensor working
within [0; 127.5]C with resolution of 0.5C. They also can generate
a PCIe upstream interrupt in case if the temperature passes through
specified thresholds. Since this thresholds interface is very broken
the created hwmon-sysfs interface exposes only the next set of hwmon
nodes: current input temperature, lowest and highest values measured,
history resetting, value offset. HWmon alarm interface isn't provided.
IDT PCIe switch also've got an ADC/filter settings of the sensor.
This driver doesn't expose them to the hwmon-sysfs interface at the
moment, except the offset node.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In order to create a hwmon interface for the IDT PCIe-switch temperature
sensor the already available reader method should be improved. Particularly
we need to redesign it so one would be able to read temperature/offset
values from registers of the passed types. Since IDT sensor interface
provides temperature in unsigned format 0:7:1 (7 bits for real value
and one for fraction) we also need to have helpers for the typical sysfs
temperature data type conversion to and from this format. Even though
the IDT PCIe-switch provided temperature offset got the same but signed
type it can be translated by these methods too.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Kaige Li