[ Upstream commit f9c4845385 ]
ip_finish_output_gso() may call .ndo_features_check() even before the
skb has a L2 header. This conflicts with qeth_get_ip_version()'s attempt
to inspect the L2 header via vlan_eth_hdr().
Switch to vlan_get_protocol(), as already used further down in the
common qeth_features_check() path.
Fixes: f13ade1993 ("s390/qeth: run non-offload L3 traffic over common xmit path")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a7f65583 upstream.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0ede91f83a upstream.
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a29ea01653 upstream.
Prevent _lcu_update from adding a device to a pavgroup if the LCU still
requires an update. The data is not reliable any longer and in parallel
devices might have been moved on the lists already.
This might lead to list corruptions or invalid PAV grouping.
Only add devices to a pavgroup if the LCU is up to date. Additional steps
are taken by the scheduled lcu update.
Fixes: 8e09f21574 ("[S390] dasd: add hyper PAV support to DASD device driver, part 1")
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 658a337a60 upstream.
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b4 ("s390/dasd: fix endless loop after read unit address configuration")
Cc: stable@vger.kernel.org #5.3
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ed10e16e5 ]
When qeth_iqd_tx_complete() detects that a TX buffer requires additional
async completion via QAOB, it might fail to replace the queue entry's
metadata (and ends up triggering recovery).
Assume now that the device gets torn down, overruling the recovery.
If the QAOB notification then arrives before the tear down has
sufficiently progressed, the buffer state is changed to
QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob().
The tear down code calls qeth_drain_output_queue(), where
qeth_cleanup_handled_pending() will then attempt to replace such a
buffer _again_. If it succeeds this time, the buffer ends up dangling in
its replacement's ->next_pending list ... where it will never be freed,
since there's no further call to qeth_cleanup_handled_pending().
But the second attempt isn't actually needed, we can simply leave the
buffer on the queue and re-use it after a potential recovery has
completed. The qeth_clear_output_buffer() in qeth_drain_output_queue()
will ensure that it's in a clean state again.
Fixes: 72861ae792 ("qeth: recovery through asynchronous delivery")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8908f36d20 ]
The two expected notification sequences are
1. TX_NOTIFY_PENDING with a subsequent TX_NOTIFY_DELAYED_*, when
our TX completion code first observed the pending TX and the QAOB
then completes at a later time; or
2. TX_NOTIFY_OK, when qeth_qdio_handle_aob() picked up the QAOB
completion before our TX completion code even noticed that the TX
was pending.
But as qeth_iqd_tx_complete() and qeth_qdio_handle_aob() can run
concurrently, we may end up with a race that results in a sequence of
TX_NOTIFY_DELAYED_* followed by TX_NOTIFY_PENDING. Which would confuse
the af_iucv code in its tracking of pending transmits.
Rework the notification code, so that qeth_qdio_handle_aob() defers its
notification if the TX completion code is still active.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 34c7f50f7d ]
Calling into socket code is ugly already, at least check whether we are
dealing with the expected sk_family. Only looking at skb->protocol is
bound to cause troubles (consider eg. af_packet).
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f117cb854 upstream.
When requeueing all requests on the device request queue to the blocklayer
we might get to an ERP (error recovery) request that is a copy of an
original CQR.
Those requests do not have blocklayer request information or a pointer to
the dasd_queue set. When trying to access those data it will lead to a
null pointer dereference in dasd_requeue_all_requests().
Fix by checking if the request is an ERP request that can simply be
ignored. The blocklayer request will be requeued by the original CQR that
is on the device queue right behind the ERP request.
Fixes: 9487cfd343 ("s390/dasd: fix handling of internal requests")
Cc: <stable@vger.kernel.org> #4.16
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b35047eb4 upstream.
When both the paes and the pkey kernel module are statically build
into the kernel, the paes cipher selftests run before the pkey
kernel module is initialized. So a static variable set in the pkey
init function and used in the pkey_clr2protkey function is not
initialized when the paes cipher's selftests request to call pckmo for
transforming a clear key value into a protected key.
This patch moves the initial setup of the static variable into
the function pck_clr2protkey. So it's possible, to use the function
for transforming a clear to a protected key even before the pkey
init function has been called and the paes selftests may run
successful.
Reported-by: Alexander Egorenkov <Alexander.Egorenkov@ibm.com>
Cc: <stable@vger.kernel.org> # 4.20
Fixes: f822ad2c2c ("s390/pkey: move pckmo subfunction available checks away from module init")
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a04f0ecacd ]
The only time that our Bridgeport role should change is when we change
the configuration ourselves. In which case we also adjust our internal
state tracking, no need to do it again when we receive the corresponding
event.
Removing the locked section helps a subsequent patch that needs to flush
the workqueue while under sbp_lock.
It would be nice to raise a warning here in case HW does weird things
after all, but this could end up generating false-positives when we
change the configuration ourselves.
Suggested-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f7e80983f0 upstream.
reqcnt is an u32 pointer but we do copy sizeof(reqcnt) which is the
size of the pointer. This means we only copy 8 byte. Let us copy
the full monty.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: stable@vger.kernel.org
Fixes: af4a72276d ("s390/zcrypt: Support up to 256 crypto adapters.")
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 709192d531 upstream.
A discard request that writes zeros using the global kernel internal
ZERO_PAGE will fail for machines with more than 2GB of memory due to the
location of the ZERO_PAGE.
Fix this by using a driver owned global zero page allocated with GFP_DMA
flag set.
Fixes: 28b841b3a7 ("s390/dasd: Add discard support for FBA devices")
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Cc: <stable@vger.kernel.org> # 4.14+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8719b6d29d ]
request_irq() is preferred over setup_irq(). Invocations of setup_irq()
occur after memory allocators are ready.
Per tglx[1], setup_irq() existed in olden days when allocators were not
ready by the time early interrupts were initialized.
Hence replace setup_irq() by request_irq().
[1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Message-Id: <20200304005049.5291-1-afzal.mohd.ma@gmail.com>
[heiko.carstens@de.ibm.com: replace pr_err with panic]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b6186d7fb5 upstream.
Tests showed that under stress conditions the kernel may
temporary fail to allocate 256k with kmalloc. However,
this fix reworks the related code in the cca_findcard2()
function to use kvmalloc instead.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reviewed-by: Ingo Franzki <ifranzki@linux.ibm.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0b8eb2ee9d ]
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2d9a2c5f58 upstream.
Before v4.15 commit 75492a5156 ("s390/scsi: Convert timers to use
timer_setup()"), we intentionally only passed zfcp_adapter as context
argument to zfcp_fsf_request_timeout_handler(). Since we only trigger
adapter recovery, it was unnecessary to sync against races between timeout
and (late) completion. Likewise, we only passed zfcp_erp_action as context
argument to zfcp_erp_timeout_handler(). Since we only wakeup an ERP action,
it was unnecessary to sync against races between timeout and (late)
completion.
Meanwhile the timeout handlers get timer_list as context argument and do a
timer-specific container-of to zfcp_fsf_req which can have been freed.
Fix it by making sure that any request timeout handlers, that might just
have started before del_timer(), are completed by using del_timer_sync()
instead. This ensures the request free happens afterwards.
Space time diagram of potential use-after-free:
Basic idea is to have 2 or more pending requests whose timeouts run out at
almost the same time.
req 1 timeout ERP thread req 2 timeout
---------------- ---------------- ---------------------------------------
zfcp_fsf_request_timeout_handler
fsf_req = from_timer(fsf_req, t, timer)
adapter = fsf_req->adapter
zfcp_qdio_siosl(adapter)
zfcp_erp_adapter_reopen(adapter,...)
zfcp_erp_strategy
...
zfcp_fsf_req_dismiss_all
list_for_each_entry_safe
zfcp_fsf_req_complete 1
del_timer 1
zfcp_fsf_req_free 1
zfcp_fsf_req_complete 2
zfcp_fsf_request_timeout_handler
del_timer 2
fsf_req = from_timer(fsf_req, t, timer)
zfcp_fsf_req_free 2
adapter = fsf_req->adapter
^^^^^^^ already freed
Link: https://lore.kernel.org/r/20200813152856.50088-1-maier@linux.ibm.com
Fixes: 75492a5156 ("s390/scsi: Convert timers to use timer_setup()")
Cc: <stable@vger.kernel.org> #4.15+
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f4aa52387 upstream.
During initialization of the DASD DIAG driver a request is issued
that has a bio structure that resides on the stack. With virtually
mapped kernel stacks this bio address might be in virtual storage
which is unsuitable for usage with the diag250 call.
In this case the device can not be set online using the DIAG
discipline and fails with -EOPNOTSUP.
In the system journal the following error message is presented:
dasd: X.X.XXXX Setting the DASD online with discipline DIAG failed
with rc=-95
Fix by allocating the bio structure instead of having it on the stack.
Fixes: ce3dc44749 ("s390: add support for virtually mapped kernel stacks")
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: stable@vger.kernel.org #4.20
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 02472e28b9 ]
Discard events that don't contain any entries. This shouldn't happen,
but subsequent code relies on being able to use entry 0. So better
be safe than accessing garbage.
Fixes: b4d72c08b3 ("qeth: bridgeport support - basic control")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e2dfcfba00 ]
Current(?) OSA devices also store their cmd-specific return codes for
SET_ACCESS_CONTROL cmds into the top-level cmd->hdr.return_code.
So once we added stricter checking for the top-level field a while ago,
none of the error logic that rolls back the user's configuration to its
old state is applied any longer.
For this specific cmd, go back to the old model where we peek into the
cmd structure even though the top-level field indicated an error.
Fixes: 686c97ee29 ("s390/qeth: fix error handling in adapter command callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 936e6b85da upstream.
Suppose that, for unrelated reasons, FSF requests on behalf of recovery are
very slow and can run into the ERP timeout.
In the case at hand, we did adapter recovery to a large degree. However
due to the slowness a LUN open is pending so the corresponding fc_rport
remains blocked. After fast_io_fail_tmo we trigger close physical port
recovery for the port under which the LUN should have been opened. The new
higher order port recovery dismisses the pending LUN open ERP action and
dismisses the pending LUN open FSF request. Such dismissal decouples the
ERP action from the pending corresponding FSF request by setting
zfcp_fsf_req->erp_action to NULL (among other things)
[zfcp_erp_strategy_check_fsfreq()].
If now the ERP timeout for the pending open LUN request runs out, we must
not use zfcp_fsf_req->erp_action in the ERP timeout handler. This is a
problem since v4.15 commit 75492a5156 ("s390/scsi: Convert timers to use
timer_setup()"). Before that we intentionally only passed zfcp_erp_action
as context argument to zfcp_erp_timeout_handler().
Note: The lifetime of the corresponding zfcp_fsf_req object continues until
a (late) response or an (unrelated) adapter recovery.
Just like the regular response path ignores dismissed requests
[zfcp_fsf_req_complete() => zfcp_fsf_protstatus_eval() => return early] the
ERP timeout handler now needs to ignore dismissed requests. So simply
return early in the ERP timeout handler if the FSF request is marked as
dismissed in its status flags. To protect against the race where
zfcp_erp_strategy_check_fsfreq() dismisses and sets
zfcp_fsf_req->erp_action to NULL after our previous status flag check,
return early if zfcp_fsf_req->erp_action is NULL. After all, the former
ERP action does not need to be woken up as that was already done as part of
the dismissal above [zfcp_erp_action_dismiss()].
This fixes the following panic due to kernel page fault in IRQ context:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000483
Fault in home space mode while using kernel ASCE.
AS:000009859238c00b R2:00000e3e7ffd000b R3:00000e3e7ffcc007 S:00000e3e7ffd7000 P:000000000000013d
Oops: 0004 ilc:2 [#1] SMP
Modules linked in: ...
CPU: 82 PID: 311273 Comm: stress Kdump: loaded Tainted: G E X ...
Hardware name: IBM 8561 T01 701 (LPAR)
Krnl PSW : 0404c00180000000 001fffff80549be0 (zfcp_erp_notify+0x40/0xc0 [zfcp])
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000080 00000e3d00000000 00000000000000f0 0000000000030000
000000010028e700 000000000400a39c 000000010028e700 00000e3e7cf87e02
0000000010000000 0700098591cb67f0 0000000000000000 0000000000000000
0000033840e9a000 0000000000000000 001fffe008d6bc18 001fffe008d6bbc8
Krnl Code: 001fffff80549bd4: a7180000 lhi %r1,0
001fffff80549bd8: 4120a0f0 la %r2,240(%r10)
#001fffff80549bdc: a53e0003 llilh %r3,3
>001fffff80549be0: ba132000 cs %r1,%r3,0(%r2)
001fffff80549be4: a7740037 brc 7,1fffff80549c52
001fffff80549be8: e320b0180004 lg %r2,24(%r11)
001fffff80549bee: e31020e00004 lg %r1,224(%r2)
001fffff80549bf4: 412020e0 la %r2,224(%r2)
Call Trace:
[<001fffff80549be0>] zfcp_erp_notify+0x40/0xc0 [zfcp]
[<00000985915e26f0>] call_timer_fn+0x38/0x190
[<00000985915e2944>] expire_timers+0xfc/0x190
[<00000985915e2ac4>] run_timer_softirq+0xec/0x218
[<0000098591ca7c4c>] __do_softirq+0x144/0x398
[<00000985915110aa>] do_softirq_own_stack+0x72/0x88
[<0000098591551b58>] irq_exit+0xb0/0xb8
[<0000098591510c6a>] do_IRQ+0x82/0xb0
[<0000098591ca7140>] ext_int_handler+0x128/0x12c
[<0000098591722d98>] clear_subpage.constprop.13+0x38/0x60
([<000009859172ae4c>] clear_huge_page+0xec/0x250)
[<000009859177e7a2>] do_huge_pmd_anonymous_page+0x32a/0x768
[<000009859172a712>] __handle_mm_fault+0x88a/0x900
[<000009859172a860>] handle_mm_fault+0xd8/0x1b0
[<0000098591529ef6>] do_dat_exception+0x136/0x3e8
[<0000098591ca6d34>] pgm_check_handler+0x1c8/0x220
Last Breaking-Event-Address:
[<001fffff80549c88>] zfcp_erp_timeout_handler+0x10/0x18 [zfcp]
Kernel panic - not syncing: Fatal exception in interrupt
Link: https://lore.kernel.org/r/20200623140242.98864-1-maier@linux.ibm.com
Fixes: 75492a5156 ("s390/scsi: Convert timers to use timer_setup()")
Cc: <stable@vger.kernel.org> #4.15+
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75e82bec6b ]
qdio_establish() calls qdio_setup_thinint() via qdio_setup_irq().
If the subsequent qdio_establish_thinint() fails, we miss to put the
DSCI again. Thus the DSCI isn't available for re-use. Given enough of
such errors, we could end up with having only the shared DSCI available.
Merge qdio_setup_thinint() into qdio_establish_thinint(), and deal with
such an error internally.
Fixes: 779e6e1c72 ("[S390] qdio: new qdio driver.")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 29b74cb75e ]
Fix to return negative error code -ENOMEM from the smcd_alloc_dev()
error handling case instead of 0, as done elsewhere in this function.
Fixes: 684b89bc39 ("s390/ism: add device driver for internal shared memory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 05ce3e53f3 ]
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The io_subchannel driver will do so when the associated
ccw_device has been registered -- but unconditionally, so more
ADD uevents will be generated if a subchannel has been unbound
from the io_subchannel driver and later rebound.
To fix this, only generate the ADD event if uevents were still
suppressed for the device.
Fixes: fa1a8c23eb ("s390: cio: Delay uevents for subchannels")
Message-Id: <20200327124503.9794-2-cohuck@redhat.com>
Reported-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2bc55eaeb8 ]
The common I/O layer delays the ADD uevent for subchannels and
delegates generating this uevent to the individual subchannel
drivers. The vfio-ccw I/O subchannel driver, however, did not
do that, and will not generate an ADD uevent for subchannels
that had not been bound to a different driver (or none at all,
which also triggers the uevent).
Generate the ADD uevent at the end of the probe function if
uevents were still suppressed for the device.
Message-Id: <20200327124503.9794-3-cohuck@redhat.com>
Fixes: 63f1934d56 ("vfio: ccw: basic implementation for vfio_ccw driver")
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 819732be9f upstream.
v2.6.27 commit cc8c282963 ("[SCSI] zfcp: Automatically attach remote
ports") introduced zfcp automatic port scan.
Before that, the user had to use the sysfs attribute "port_add" of an FCP
device (adapter) to add and open remote (target) ports, even for the remote
peer port in point-to-point topology. That code path did a proper port open
recovery trigger taking the erp_lock.
Since above commit, a new helper function zfcp_erp_open_ptp_port()
performed an UNlocked port open recovery trigger. This can race with other
parallel recovery triggers. In zfcp_erp_action_enqueue() this could corrupt
e.g. adapter->erp_total_count or adapter->erp_ready_head.
As already found for fabric topology in v4.17 commit fa89adba19 ("scsi:
zfcp: fix infinite iteration on ERP ready list"), there was an endless loop
during tracing of rport (un)block. A subsequent v4.18 commit 9e156c54ac
("scsi: zfcp: assert that the ERP lock is held when tracing a recovery
trigger") introduced a lockdep assertion for that case.
As a side effect, that lockdep assertion now uncovered the unlocked code
path for PtP. It is from within an adapter ERP action:
zfcp_erp_strategy[1479] intentionally DROPs erp lock around
zfcp_erp_strategy_do_action()
zfcp_erp_strategy_do_action[1441] NO erp lock
zfcp_erp_adapter_strategy[876] NO erp lock
zfcp_erp_adapter_strategy_open[855] NO erp lock
zfcp_erp_adapter_strategy_open_fsf[806]NO erp lock
zfcp_erp_adapter_strat_fsf_xconf[772] erp lock only around
zfcp_erp_action_to_running(),
BUT *_not_* around
zfcp_erp_enqueue_ptp_port()
zfcp_erp_enqueue_ptp_port[728] BUG: *_not_* taking erp lock
_zfcp_erp_port_reopen[432] assumes to be called with erp lock
zfcp_erp_action_enqueue[314] assumes to be called with erp lock
zfcp_dbf_rec_trig[288] _checks_ to be called with erp lock:
lockdep_assert_held(&adapter->erp_lock);
It causes the following lockdep warning:
WARNING: CPU: 2 PID: 775 at drivers/s390/scsi/zfcp_dbf.c:288
zfcp_dbf_rec_trig+0x16a/0x188
no locks held by zfcperp0.0.17c0/775.
Fix this by using the proper locked recovery trigger helper function.
Link: https://lore.kernel.org/r/20200312174505.51294-2-maier@linux.ibm.com
Fixes: cc8c282963 ("[SCSI] zfcp: Automatically attach remote ports")
Cc: <stable@vger.kernel.org> #v2.6.27+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1741385280 ]
qeth_init_qdio_queues() fills the RX ring with an initial set of
RX buffers. If qeth_init_input_buffer() fails to back one of the RX
buffers with memory, we need to bail out and report the error.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 240c194849 ]
When an OSA device in prio-queue setup is reduced to 1 TX queue due to
HW restrictions, we reset its the default_out_queue to 0.
In the old code this was needed so that qeth_get_priority_queue() gets
the queue selection right. But with proper multiqueue support we already
reduced dev->real_num_tx_queues to 1, and so the stack puts all traffic
on txq 0 without even calling .ndo_select_queue.
Thus we can preserve the user's configuration, and apply it if the OSA
device later re-gains support for multiple TX queues.
Fixes: 73dc2daf11 ("s390/qeth: add TX multiqueue support for OSA devices")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5e6bdd37c5 upstream.
Devices are formatted in multiple of tracks.
For an Extent Space Efficient (ESE) volume we get errors when accessing
unformatted tracks. In this case the driver either formats the track on
the flight for write requests or returns zero data for read requests.
In case a request spans multiple tracks, the indication of an unformatted
track presented for the first track is incorrectly applied to all tracks
covered by the request. As a result, tracks containing data will be handled
as empty, resulting in zero data being returned on read, or overwriting
existing data with zero on write.
Fix by determining the track that gets the NRF error.
For write requests only format the track that is surely not formatted.
For Read requests all tracks before have returned valid data and should not
be touched.
All tracks after the unformatted track might be formatted or not. Those are
returned to the blocklayer to build a new request.
When using alias devices there is a chance that multiple write requests
trigger a format of the same track which might lead to data loss. Ensure
that a track is formatted only once by maintaining a list of currently
processed tracks.
Fixes: 5e2b17e712 ("s390/dasd: Add dynamic formatting support for ESE volumes")
Cc: stable@vger.kernel.org # 5.3+
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e9091ffd6a ]
As the comment says, sl->sbal holds an absolute address. qeth currently
solves this through wild casting, while zfcp doesn't care.
Handle this properly in the code that actually builds the SL.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com> [for qdio]
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f3846f095 upstream.
When getting or setting VNICC parameters, the error code EOPNOTSUPP
should have precedence over EBUSY.
EBUSY is used because vnicc feature and bridgeport feature are mutually
exclusive, which is a temporary condition.
Whereas EOPNOTSUPP indicates that the HW does not support all or parts of
the vnicc feature.
This issue causes the vnicc sysfs params to show 'blocked by bridgeport'
for HW that does not support VNICC at all.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fcd98d4002 ]
The internal statistic counters for the total number of
requests processed per card and per queue used integers. So they do
wrap after a rather huge amount of crypto requests processed. This
patch introduces uint64 counters which should hold much longer but
still may wrap. The sysfs attributes request_count for card and queue
also used only %ld and now display the counter value with %llu.
This is not a security relevant fix. The int overflow which happened
is not in any way exploitable as a security breach.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit aab73d278d upstream.
The pkey ioctl call PKEY_SEC2PROTK updates a struct pkey_protkey
on return. The protected key is stored in, the protected key type
is stored in but the len information was not updated. This patch
now fixes this and so the len field gets an update to refrect
the actual size of the protected key value returned.
Fixes: efc598e6c8 ("s390/zcrypt: move cca misc functions to new code file")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Reported-by: Christian Rund <RUNDC@de.ibm.com>
Suggested-by: Ingo Franzki <ifranzki@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0c874cd042 ]
This patch moves the reset invocation of an ap device when
fresh detected from the ap bus to the probe() function of
the driver responsible for this device.
The virtualisation of ap devices makes it necessary to
remove unconditioned resets on fresh appearing apqn devices.
It may be that such a device is already enabled for guest
usage. So there may be a race condition between host ap bus
and guest ap bus doing the reset. This patch moves the
reset from the ap bus to the zcrypt drivers. So if there
is no zcrypt driver bound to an ap device - for example
the ap device is bound to the vfio device driver - the
ap device is untouched passed to the vfio device driver.
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f9e50b02a9 ]
The cio layer's intparm logic does not align itself well with how qeth
manages cmd IOs. When an active IO gets terminated via halt/clear, the
corresponding IRQ's intparm does not reflect the cmd buffer but rather
the intparm that was passed to ccw_device_halt() / ccw_device_clear().
This behaviour was recently clarified in
commit b91d9e67e5 ("s390/cio: fix intparm documentation").
As a result, qeth_irq() currently doesn't cancel a cmd that was
terminated via halt/clear. This primarily causes us to leak
card->read_cmd after the qeth device is removed, since our IO path still
holds a refcount for this cmd.
For qeth this means that we need to keep track of which IO is pending on
a device ('active_cmd'), and use this as the intparm when calling
halt/clear. Otherwise qeth_irq() can't match the subsequent IRQ to its
cmd buffer.
Since we now keep track of the _expected_ intparm, we can also detect
any mismatch; this would constitute a bug somewhere in the lower layers.
In this case cancel the active cmd - we effectively "lost" the IRQ and
should not expect any further notification for this IO.
Fixes: 405548959c ("s390/qeth: add support for dynamically allocated cmds")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 94dd3bada5 upstream.
Regression tests showed that the CCA cipher key function which
generates an CCA cipher key with given clear key value does not work
correctly. At parsing the reply CPRB two limits are wrong calculated
resulting in rejecting the reply as invalid with s390dbf message
"_ip_cprb_helper reply with invalid or unknown key block".
Fixes: f2bbc96e7c ("s390/pkey: add CCA AES cipher key support")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b6c7b55cf ]
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: b333293058 ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0b698c838e upstream.
I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 742d4d4083 ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d1b9ae1864 upstream.
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8a66d8004 upstream.
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68c57bfd52 upstream.
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8b5026bc16 upstream.
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 39bdbf3e64 ]
ENOTSUPP is not uapi, use EOPNOTSUPP instead.
Fixes: d66cb37e96 ("qeth: Add new priority queueing options")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f399305cd ]
When managing the promiscuous mode during an RX modeset, qeth caches the
current HW state to avoid repeated programming of the same state on each
modeset.
But while tearing down a device, we forget to clear the cached state. So
when the device is later set online again, the initial RX modeset
doesn't program the promiscuous mode since we believe it is already
enabled.
Fix this by clearing the cached state in the tear-down path.
Note that for the SBP variant of promiscuous mode, this accidentally
works right now because we unconditionally restore the SBP role while
re-initializing.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2e3d7fa5d2 ]
Along with z/VM NICs, there's additional device types that only support
a specific transport mode (eg. external-bridged IQD).
Identify the corresponding error code, and raise a fitting error message
so that the user knows to adjust their device configuration.
On top of that also fix the subsequent error path, so that the rejected
cmd doesn't need to wait for a timeout but gets cancelled straight away.
Fixes: 4a71df5004 ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 00b39f698a ]
If for whatever reason the dasd_eckd_check_characteristics() function
exits after at least some paths have their configuration data
allocated those data is never freed again. In the error case the
device->private pointer is set to NULL and dasd_eckd_uncheck_device()
will exit without freeing the path data because of this NULL pointer.
Fix by calling dasd_eckd_clear_conf_data() for error cases.
Also use dasd_eckd_clear_conf_data() in dasd_eckd_uncheck_device()
to avoid code duplication.
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd4b3c83b9 ]
The max data count (mdc) is an unsigned 16-bit integer value as per AR
documentation and is received via ccw_device_get_mdc() for a specific
path mask from the CIO layer. The function itself also always returns a
positive mdc value or 0 in case mdc isn't supported or couldn't be
determined.
Though, the comment for this function describes a negative return value
to indicate failures.
As a result, the DASD device driver interprets the return value of
ccw_device_get_mdc() incorrectly. The error case is essentially a dead
code path.
To fix this behaviour, check explicitly for a return value of 0 and
change the comment for ccw_device_get_mdc() accordingly.
This fix merely enables the error code path in the DASD functions
get_fcx_max_data() and verify_fcx_max_data(). The actual functionality
stays the same and is still correct.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Julian Wiedmann