The following race is observed due to which a processes faulting on a
swap entry, finds the page neither in swapcache nor swap. This causes
zram to give a zero filled page that gets mapped to the process,
resulting in a user space crash later.
Consider parent and child processes Pa and Pb sharing the same swap slot
with swap_count 2. Swap is on zram with SWP_SYNCHRONOUS_IO set.
Virtual address 'VA' of Pa and Pb points to the shared swap entry.
Pa Pb
fault on VA fault on VA
do_swap_page do_swap_page
lookup_swap_cache fails lookup_swap_cache fails
Pb scheduled out
swapin_readahead (deletes zram entry)
swap_free (makes swap_count 1)
Pb scheduled in
swap_readpage (swap_count == 1)
Takes SWP_SYNCHRONOUS_IO path
zram enrty absent
zram gives a zero filled page
Fix this by making sure that swap slot is freed only when swap count
drops down to one.
Link: http://lkml.kernel.org/r/1571743294-14285-1-git-send-email-vinmenon@codeaurora.org
Fixes: aa8d22a11d ("mm: swap: SWP_SYNCHRONOUS_IO: skip swapcache only if swapped page has no other reference")
Signed-off-by: Vinayak Menon <vinmenon@codeaurora.org>
Suggested-by: Minchan Kim <minchan@google.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap_extent is used to map swap page offset to backing device's block
offset. For a continuous block range, one swap_extent is used and all
these swap_extents are managed in a linked list.
These swap_extents are used by map_swap_entry() during swap's read and
write path. To find out the backing device's block offset for a page
offset, the swap_extent list will be traversed linearly, with
curr_swap_extent being used as a cache to speed up the search.
This works well as long as swap_extents are not huge or when the number
of processes that access swap device are few, but when the swap device
has many extents and there are a number of processes accessing the swap
device concurrently, it can be a problem. On one of our servers, the
disk's remaining size is tight:
$df -h
Filesystem Size Used Avail Use% Mounted on
... ...
/dev/nvme0n1p1 1.8T 1.3T 504G 72% /home/t4
When creating a 80G swapfile there, there are as many as 84656 swap
extents. The end result is, kernel spends abou 30% time in
map_swap_entry() and swap throughput is only 70MB/s.
As a comparison, when I used smaller sized swapfile, like 4G whose
swap_extent dropped to 2000, swap throughput is back to 400-500MB/s and
map_swap_entry() is about 3%.
One downside of using rbtree for swap_extent is, 'struct rbtree' takes
24 bytes while 'struct list_head' takes 16 bytes, that's 8 bytes more
for each swap_extent. For a swapfile that has 80k swap_extents, that
means 625KiB more memory consumed.
Test:
Since it's not possible to reboot that server, I can not test this patch
diretly there. Instead, I tested it on another server with NVMe disk.
I created a 20G swapfile on an NVMe backed XFS fs. By default, the
filesystem is quite clean and the created swapfile has only 2 extents.
Testing vanilla and this patch shows no obvious performance difference
when swapfile is not fragmented.
To see the patch's effects, I used some tweaks to manually fragment the
swapfile by breaking the extent at 1M boundary. This made the swapfile
have 20K extents.
nr_task=4
kernel swapout(KB/s) map_swap_entry(perf) swapin(KB/s) map_swap_entry(perf)
vanilla 165191 90.77% 171798 90.21%
patched 858993 +420% 2.16% 715827 +317% 0.77%
nr_task=8
kernel swapout(KB/s) map_swap_entry(perf) swapin(KB/s) map_swap_entry(perf)
vanilla 306783 92.19% 318145 87.76%
patched 954437 +211% 2.35% 1073741 +237% 1.57%
swapout: the throughput of swap out, in KB/s, higher is better 1st
map_swap_entry: cpu cycles percent sampled by perf swapin: the
throughput of swap in, in KB/s, higher is better. 2nd map_swap_entry:
cpu cycles percent sampled by perf
nr_task=1 doesn't show any difference, this is due to the curr_swap_extent
can be effectively used to cache the correct swap extent for single task
workload.
[akpm@linux-foundation.org: s/BUG_ON(1)/BUG()/]
Link: http://lkml.kernel.org/r/20190523142404.GA181@aaronlu
Signed-off-by: Aaron Lu <ziqian.lzq@antfin.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap_readpage() sets waiter = bio->bi_private even if synchronous = F,
this means that the caller can get the spurious wakeup after return.
This can be fatal if blk_wake_io_task() does
set_current_state(TASK_RUNNING) after the caller does
set_special_state(), in the worst case the kernel can crash in
do_task_dead().
Link: http://lkml.kernel.org/r/20190704160301.GA5956@redhat.com
Fixes: 0619317ff8 ("block: add polled wakeup task helper")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Qian Cai <cai@lca.pw>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
0-Day test system reported some OOM regressions for several THP
(Transparent Huge Page) swap test cases. These regressions are bisected
to 6861428921 ("block: always define BIO_MAX_PAGES as 256"). In the
commit, BIO_MAX_PAGES is set to 256 even when THP swap is enabled. So the
bio_alloc(gfp_flags, 512) in get_swap_bio() may fail when swapping out
THP. That causes the OOM.
As in the patch description of 6861428921 ("block: always define
BIO_MAX_PAGES as 256"), THP swap should use multi-page bvec to write THP
to swap space. So the issue is fixed via doing that in get_swap_bio().
BTW: I remember I have checked the THP swap code when 6861428921
("block: always define BIO_MAX_PAGES as 256") was merged, and thought the
THP swap code needn't to be changed. But apparently, I was wrong. I
should have done this at that time.
Link: http://lkml.kernel.org/r/20190624075515.31040-1-ying.huang@intel.com
Fixes: 6861428921 ("block: always define BIO_MAX_PAGES as 256")
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swap_readpage() wants to do polling to bring in pages if asked to, but
it doesn't mark the bio as being polled. Additionally, the looping
around the blk_poll() check isn't correct - if we get a zero return, we
should call io_schedule(), we can't just assume that the bio has
completed. The regular bio->bi_private check should be used for that.
Link: http://lkml.kernel.org/r/e15243a8-2cdf-c32c-ecee-f289377c8ef9@kernel.dk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mostly reverts commit 849a370016 ("block: avoid ordered task
state change for polled IO"). It was wrongly claiming that the ordering
wasn't necessary. The memory barrier _is_ necessary.
If something is truly polling and not going to sleep, it's the whole
state setting that is unnecessary, not the memory barrier. Whenever you
set your state to a sleeping state, you absolutely need the memory
barrier.
Note that sometimes the memory barrier can be elsewhere. For example,
the ordering might be provided by an external lock, or by setting the
process state to sleeping before adding yourself to the wait queue list
that is used for waking up (where the wait queue lock itself will
guarantee that any wakeup will correctly see the sleeping state).
But none of those cases were true here.
NOTE! Some of the polling paths may indeed be able to drop the state
setting entirely, at which point the memory barrier also goes away.
(Also note that this doesn't revert the TASK_RUNNING cases: there is no
race between a wakeup and setting the process state to TASK_RUNNING,
since the end result doesn't depend on ordering).
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A prior patch in this series added blkg association to bios issued by
cgroups. There are two other paths that we want to attribute work back
to the appropriate cgroup: swap and writeback. Here we modify the way
swap tags bios to include the blkg. Writeback will be tackle in the next
patch.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_poll() has always kept spinning until it found an IO. This is
fine for SYNC polling, since we need to find one request we have
pending, but in preparation for ASYNC polling it can be beneficial
to just check if we have any entries available or not.
Existing callers are converted to pass in 'spin == true', to retain
the old behavior.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For the core poll helper, the task state setting don't need to imply any
atomics, as it's the current task itself that is being modified and
we're not going to sleep.
For IRQ driven, the wakeup path have the necessary barriers to not need
us using the heavy handed version of the task state setting.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we're polling for IO on a device that doesn't use interrupts, then
IO completion loop (and wake of task) is done by submitting task itself.
If that is the case, then we don't need to enter the wake_up_process()
function, we can simply mark ourselves as TASK_RUNNING.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=0zM4
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20181102' of git://git.kernel.dk/linux-block
Pull block layer fixes from Jens Axboe:
"The biggest part of this pull request is the revert of the blkcg
cleanup series. It had one fix earlier for a stacked device issue, but
another one was reported. Rather than play whack-a-mole with this,
revert the entire series and try again for the next kernel release.
Apart from that, only small fixes/changes.
Summary:
- Indentation fixup for mtip32xx (Colin Ian King)
- The blkcg cleanup series revert (Dennis Zhou)
- Two NVMe fixes. One fixing a regression in the nvme request
initialization in this merge window, causing nvme-fc to not work.
The other is a suspend/resume p2p resource issue (James, Keith)
- Fix sg discard merge, allowing us to merge in cases where we didn't
before (Jianchao Wang)
- Call rq_qos_exit() after the queue is frozen, preventing a hang
(Ming)
- Fix brd queue setup, fixing an oops if we fail setting up all
devices (Ming)"
* tag 'for-linus-20181102' of git://git.kernel.dk/linux-block:
nvme-pci: fix conflicting p2p resource adds
nvme-fc: fix request private initialization
blkcg: revert blkcg cleanups series
block: brd: associate with queue until adding disk
block: call rq_qos_exit() after queue is frozen
mtip32xx: clean an indentation issue, remove extraneous tabs
block: fix the DISCARD request merge
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
The SWP_FILE flag serves two purposes: to make swap_{read,write}page() go
through the filesystem, and to make swapoff() call ->swap_deactivate().
For Btrfs, we want the latter but not the former, so split this flag into
two. This makes us always call ->swap_deactivate() if ->swap_activate()
succeeded, not just if it didn't add any swap extents itself.
This also resolves the issue of the very misleading name of SWP_FILE,
which is only used for swap files over NFS.
Link: http://lkml.kernel.org/r/6d63d8668c4287a4f6d203d65696e96f80abdfc7.1536704650.git.osandov@fb.com
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Sterba <dsterba@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the iov_iter struct, separate the iterator type from the iterator
direction and use accessor functions to access them in most places.
Convert a bunch of places to use switch-statements to access them rather
then chains of bitwise-AND statements. This makes it easier to add further
iterator types. Also, this can be more efficient as to implement a switch
of small contiguous integers, the compiler can use ~50% fewer compare
instructions than it has to use bitwise-and instructions.
Further, cease passing the iterator type into the iterator setup function.
The iterator function can set that itself. Only the direction is required.
Signed-off-by: David Howells <dhowells@redhat.com>
A prior patch in this series added blkg association to bios issued by
cgroups. There are two other paths that we want to attribute work back
to the appropriate cgroup: swap and writeback. Here we modify the way
swap tags bios to include the blkg. Writeback will be tackle in the next
patch.
Signed-off-by: Dennis Zhou <dennisszhou@gmail.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For backcharging we need to know who the page belongs to when swapping
it out. We don't worry about things that do ->rw_page (zram etc) at the
moment, we're only worried about pages that actually go to a block
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just like REQ_META, it's important to know the IO coming down is swap
in order to guard against potential IO priority inversion issues with
cgroups. Add REQ_SWAP and use it for all swap IO, and add it to our
bio_issue_as_root_blkg helper.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch converts to bio_first_bvec_all() & bio_first_page_all() for
retrieving the 1st bvec/page, and prepares for supporting multipage bvec.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With fast swap storage, the platforms want to use swap more aggressively
and swap-in is crucial to application latency.
The rw_page() based synchronous devices like zram, pmem and btt are such
fast storage. When I profile swapin performance with zram lz4
decompress test, S/W overhead is more than 70%. Maybe, it would be
bigger in nvdimm.
This patch aims to reduce swap-in latency by skipping swapcache if the
swap device is synchronous device like rw_page based device. It
enhances 45% my swapin test(5G sequential swapin, no readahead, from
2.41sec to 1.64sec).
Link: http://lkml.kernel.org/r/1505886205-9671-5-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull core block layer updates from Jens Axboe:
"This is the main pull request for block storage for 4.15-rc1.
Nothing out of the ordinary in here, and no API changes or anything
like that. Just various new features for drivers, core changes, etc.
In particular, this pull request contains:
- A patch series from Bart, closing the whole on blk/scsi-mq queue
quescing.
- A series from Christoph, building towards hidden gendisks (for
multipath) and ability to move bio chains around.
- NVMe
- Support for native multipath for NVMe (Christoph).
- Userspace notifications for AENs (Keith).
- Command side-effects support (Keith).
- SGL support (Chaitanya Kulkarni)
- FC fixes and improvements (James Smart)
- Lots of fixes and tweaks (Various)
- bcache
- New maintainer (Michael Lyle)
- Writeback control improvements (Michael)
- Various fixes (Coly, Elena, Eric, Liang, et al)
- lightnvm updates, mostly centered around the pblk interface
(Javier, Hans, and Rakesh).
- Removal of unused bio/bvec kmap atomic interfaces (me, Christoph)
- Writeback series that fix the much discussed hundreds of millions
of sync-all units. This goes all the way, as discussed previously
(me).
- Fix for missing wakeup on writeback timer adjustments (Yafang
Shao).
- Fix laptop mode on blk-mq (me).
- {mq,name} tupple lookup for IO schedulers, allowing us to have
alias names. This means you can use 'deadline' on both !mq and on
mq (where it's called mq-deadline). (me).
- blktrace race fix, oopsing on sg load (me).
- blk-mq optimizations (me).
- Obscure waitqueue race fix for kyber (Omar).
- NBD fixes (Josef).
- Disable writeback throttling by default on bfq, like we do on cfq
(Luca Miccio).
- Series from Ming that enable us to treat flush requests on blk-mq
like any other request. This is a really nice cleanup.
- Series from Ming that improves merging on blk-mq with schedulers,
getting us closer to flipping the switch on scsi-mq again.
- BFQ updates (Paolo).
- blk-mq atomic flags memory ordering fixes (Peter Z).
- Loop cgroup support (Shaohua).
- Lots of minor fixes from lots of different folks, both for core and
driver code"
* 'for-4.15/block' of git://git.kernel.dk/linux-block: (294 commits)
nvme: fix visibility of "uuid" ns attribute
blk-mq: fixup some comment typos and lengths
ide: ide-atapi: fix compile error with defining macro DEBUG
blk-mq: improve tag waiting setup for non-shared tags
brd: remove unused brd_mutex
blk-mq: only run the hardware queue if IO is pending
block: avoid null pointer dereference on null disk
fs: guard_bio_eod() needs to consider partitions
xtensa/simdisk: fix compile error
nvme: expose subsys attribute to sysfs
nvme: create 'slaves' and 'holders' entries for hidden controllers
block: create 'slaves' and 'holders' entries for hidden gendisks
nvme: also expose the namespace identification sysfs files for mpath nodes
nvme: implement multipath access to nvme subsystems
nvme: track shared namespaces
nvme: introduce a nvme_ns_ids structure
nvme: track subsystems
block, nvme: Introduce blk_mq_req_flags_t
block, scsi: Make SCSI quiesce and resume work reliably
block: Add the QUEUE_FLAG_PREEMPT_ONLY request queue flag
...
That we we can also poll non blk-mq queues. Mostly needed for
the NVMe multipath code, but could also be useful elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull block layer updates from Jens Axboe:
"This is the first pull request for 4.14, containing most of the code
changes. It's a quiet series this round, which I think we needed after
the churn of the last few series. This contains:
- Fix for a registration race in loop, from Anton Volkov.
- Overflow complaint fix from Arnd for DAC960.
- Series of drbd changes from the usual suspects.
- Conversion of the stec/skd driver to blk-mq. From Bart.
- A few BFQ improvements/fixes from Paolo.
- CFQ improvement from Ritesh, allowing idling for group idle.
- A few fixes found by Dan's smatch, courtesy of Dan.
- A warning fixup for a race between changing the IO scheduler and
device remova. From David Jeffery.
- A few nbd fixes from Josef.
- Support for cgroup info in blktrace, from Shaohua.
- Also from Shaohua, new features in the null_blk driver to allow it
to actually hold data, among other things.
- Various corner cases and error handling fixes from Weiping Zhang.
- Improvements to the IO stats tracking for blk-mq from me. Can
drastically improve performance for fast devices and/or big
machines.
- Series from Christoph removing bi_bdev as being needed for IO
submission, in preparation for nvme multipathing code.
- Series from Bart, including various cleanups and fixes for switch
fall through case complaints"
* 'for-4.14/block' of git://git.kernel.dk/linux-block: (162 commits)
kernfs: checking for IS_ERR() instead of NULL
drbd: remove BIOSET_NEED_RESCUER flag from drbd_{md_,}io_bio_set
drbd: Fix allyesconfig build, fix recent commit
drbd: switch from kmalloc() to kmalloc_array()
drbd: abort drbd_start_resync if there is no connection
drbd: move global variables to drbd namespace and make some static
drbd: rename "usermode_helper" to "drbd_usermode_helper"
drbd: fix race between handshake and admin disconnect/down
drbd: fix potential deadlock when trying to detach during handshake
drbd: A single dot should be put into a sequence.
drbd: fix rmmod cleanup, remove _all_ debugfs entries
drbd: Use setup_timer() instead of init_timer() to simplify the code.
drbd: fix potential get_ldev/put_ldev refcount imbalance during attach
drbd: new disk-option disable-write-same
drbd: Fix resource role for newly created resources in events2
drbd: mark symbols static where possible
drbd: Send P_NEG_ACK upon write error in protocol != C
drbd: add explicit plugging when submitting batches
drbd: change list_for_each_safe to while(list_first_entry_or_null)
drbd: introduce drbd_recv_header_maybe_unplug
...
To support delay splitting THP (Transparent Huge Page) after swapped
out, we need to enhance swap writing code to support to write a THP as a
whole. This will improve swap write IO performance.
As Ming Lei <ming.lei@redhat.com> pointed out, this should be based on
multipage bvec support, which hasn't been merged yet. So this patch is
only for testing the functionality of the other patches in the series.
And will be reimplemented after multipage bvec support is merged.
Link: http://lkml.kernel.org/r/20170724051840.2309-7-ying.huang@intel.com
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ross Zwisler <ross.zwisler@intel.com> [for brd.c, zram_drv.c, pmem.c]
Cc: Shaohua Li <shli@kernel.org>
Cc: Vishal L Verma <vishal.l.verma@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This way we don't need a block_device structure to submit I/O. The
block_device has different life time rules from the gendisk and
request_queue and is usually only available when the block device node
is open. Other callers need to explicitly create one (e.g. the lightnvm
passthrough code, or the new nvme multipathing code).
For the actual I/O path all that we need is the gendisk, which exists
once per block device. But given that the block layer also does
partition remapping we additionally need a partition index, which is
used for said remapping in generic_make_request.
Note that all the block drivers generally want request_queue or
sometimes the gendisk, so this removes a layer of indirection all
over the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For fast flash disk, async IO could introduce overhead because of
context switch. block-mq now supports IO poll, which improves
performance and latency a lot. swapin is a good place to use this
technique, because the task is waiting for the swapin page to continue
execution.
In my virtual machine, directly read 4k data from a NVMe with iopoll is
about 60% better than that without poll. With iopoll support in swapin
patch, my microbenchmark (a task does random memory write) is about
10%~25% faster. CPU utilization increases a lot though, 2x and even 3x
CPU utilization. This will depend on disk speed.
While iopoll in swapin isn't intended for all usage cases, it's a win
for latency sensistive workloads with high speed swap disk. block layer
has knob to control poll in runtime. If poll isn't enabled in block
layer, there should be no noticeable change in swapin.
I got a chance to run the same test in a NVMe with DRAM as the media.
In simple fio IO test, blkpoll boosts 50% performance in single thread
test and ~20% in 8 threads test. So this is the base line. In above
swap test, blkpoll boosts ~27% performance in single thread test.
blkpoll uses 2x CPU time though.
If we enable hybid polling, the performance gain has very slight drop
but CPU time is only 50% worse than that without blkpoll. Also we can
adjust parameter of hybid poll, with it, the CPU time penality is
reduced further. In 8 threads test, blkpoll doesn't help though. The
performance is similar to that without blkpoll, but cpu utilization is
similar too. There is lock contention in swap path. The cpu time
spending on blkpoll isn't high. So overall, blkpoll swapin isn't worse
than that without it.
The swapin readahead might read several pages in in the same time and
form a big IO request. Since the IO will take longer time, it doesn't
make sense to do poll, so the patch only does iopoll for single page
swapin.
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/070c3c3e40b711e7b1390002c991e86a-b5408f0@7511894063d3764ff01ea8111f5a004d7dd700ed078797c204a24e620ddb965c
Signed-off-by: Shaohua Li <shli@fb.com>
Cc: Tim Chen <tim.c.chen@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace bi_error with a new bi_status to allow for a clear conversion.
Note that device mapper overloaded bi_error with a private value, which
we'll have to keep arround at least for now and thus propagate to a
proper blk_status_t value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add wbc_to_write_flags(), which returns the write modifier flags to use,
based on a struct writeback_control. No functional changes in this
patch, but it prepares us for factoring other wbc fields for write type.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
So they are CONFIG_DEBUG_VM-only and more informative.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Joe Perches <joe@perches.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Rik van Riel <riel@redhat.com>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 62c230bc17 ("mm: add support for a filesystem to activate
swap files and use direct_IO for writing swap pages") replaced the
swap_aops dirty hook from __set_page_dirty_no_writeback() with
swap_set_page_dirty().
For normal cases without these special SWP flags code path falls back to
__set_page_dirty_no_writeback() so the behaviour is expected to be the
same as before.
But swap_set_page_dirty() makes use of the page_swap_info() helper to
get the swap_info_struct to check for the flags like SWP_FILE,
SWP_BLKDEV etc as desired for those features. This helper has
BUG_ON(!PageSwapCache(page)) which is racy and safe only for the
set_page_dirty_lock() path.
For the set_page_dirty() path which is often needed for cases to be
called from irq context, kswapd() can toggle the flag behind the back
while the call is getting executed when system is low on memory and
heavy swapping is ongoing.
This ends up with undesired kernel panic.
This patch just moves the check outside the helper to its users
appropriately to fix kernel panic for the described path. Couple of
users of helpers already take care of SwapCache condition so I skipped
them.
Link: http://lkml.kernel.org/r/1473460718-31013-1-git-send-email-santosh.shilimkar@oracle.com
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Joe Perches <joe@perches.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Rik van Riel <riel@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jens Axboe <axboe@fb.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org> [4.7.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
generic_swapfile_activate() can take quite long time, it iterates over
all blocks of a file, so add cond_resched to it. I observed about 1
second stalls when activating a swapfile that was almost unfragmented -
this patch fixes it.
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1607221710580.4818@file01.intranet.prod.int.rdu2.redhat.com
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull vfs cleanups from Al Viro:
"More cleanups from Christoph"
* 'work.preadv2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
nfsd: use RWF_SYNC
fs: add RWF_DSYNC aand RWF_SYNC
ceph: use generic_write_sync
fs: simplify the generic_write_sync prototype
fs: add IOCB_SYNC and IOCB_DSYNC
direct-io: remove the offset argument to dio_complete
direct-io: eliminate the offset argument to ->direct_IO
xfs: eliminate the pos variable in xfs_file_dio_aio_write
filemap: remove the pos argument to generic_file_direct_write
filemap: remove pos variables in generic_file_read_iter
Including blkdev_direct_IO and dax_do_io. It has to be ki_pos to actually
work, so eliminate the superflous argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Kyeongdon reported below error which is BUG_ON(!PageSwapCache(page)) in
page_swap_info. The reason is that page_endio in rw_page unlocks the
page if read I/O is completed so we need to hold a PG_lock again to
check PageSwapCache. Otherwise, the page can be removed from swapcache.
Kernel BUG at c00f9040 [verbose debug info unavailable]
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 4 PID: 13446 Comm: RenderThread Tainted: G W 3.10.84-g9f14aec-dirty #73
task: c3b73200 ti: dd192000 task.ti: dd192000
PC is at page_swap_info+0x10/0x2c
LR is at swap_slot_free_notify+0x18/0x6c
pc : [<c00f9040>] lr : [<c00f5560>] psr: 400f0113
sp : dd193d78 ip : c2deb1e4 fp : da015180
r10: 00000000 r9 : 000200da r8 : c120fe08
r7 : 00000000 r6 : 00000000 r5 : c249a6c0 r4 : = c249a6c0
r3 : 00000000 r2 : 40080009 r1 : 200f0113 r0 : = c249a6c0
..<snip> ..
Call Trace:
page_swap_info+0x10/0x2c
swap_slot_free_notify+0x18/0x6c
swap_readpage+0x90/0x11c
read_swap_cache_async+0x134/0x1ac
swapin_readahead+0x70/0xb0
handle_pte_fault+0x320/0x6fc
handle_mm_fault+0xc0/0xf0
do_page_fault+0x11c/0x36c
do_DataAbort+0x34/0x118
Fixes: 3f2b1a04f4 ("zram: revive swap_slot_free_notify")
Signed-off-by: Minchan Kim <minchan@kernel.org>
Tested-by: Kyeongdon Kim <kyeongdon.kim@lge.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit b430e9d1c6 ("remove compressed copy from zram in-memory")
applied swap_slot_free_notify call in *end_swap_bio_read* to remove
duplicated memory between zram and memory.
However, with the introduction of rw_page in zram: 8c7f01025f ("zram:
implement rw_page operation of zram"), it became void because rw_page
doesn't need bio.
Memory footprint is really important in embedded platforms which have
small memory, for example, 512M) recently because it could start to kill
processes if memory footprint exceeds some threshold by LMK or some
similar memory management modules.
This patch restores the function for rw_page, thereby eliminating this
duplication.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: karam.lee <karam.lee@lge.com>
Cc: <sangseok.lee@lge.com>
Cc: Chan Jeong <chan.jeong@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the mm subsystem uses pr_<level> so make it consistent.
Miscellanea:
- Realign arguments
- Add missing newline to format
- kmemleak-test.c has a "kmemleak: " prefix added to the
"Kmemleak testing" logging message via pr_fmt
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Tejun Heo <tj@kernel.org> [percpu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call pre-defined helper bio_add_page() instead of open coding for
iterating through bi_io_vec[]. Doing that, it's possible to make some
parts in filesystems and mm/page_io.c simpler than before.
Acked-by: Dave Kleikamp <shaggy@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: add more description in commit message]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Stop abusing struct page functionality and the swap end_io handler, and
instead add a modified version of the blk-lib.c bio_batch helpers.
Also move the block I/O code into swap.c as they are directly tied into
each other.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Ming Lin <mlin@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Jens Axboe <axboe@fb.com>
struct kiocb now is a generic I/O container, so move it to fs.h.
Also do a #include diet for aio.h while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There is no need to pass the total request length in the kiocb, as
we already get passed in through the iov_iter argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tetsuo Handa wrote:
"Commit 62a8067a7f ("bio_vec-backed iov_iter") introduced an unnamed
union inside a struct which gcc-4.4.7 cannot handle. Name the unnamed
union as u in order to fix build failure"
Let's do this instead: there is only one place in the entire tree that
steps into this breakage. Anon structs and unions work in older gcc
versions; as the matter of fact, we have those in the tree - see e.g.
struct ieee80211_tx_info in include/net/mac80211.h
What doesn't work is handling their initializers:
struct {
int a;
union {
int b;
char c;
};
} x[2] = {{.a = 1, .c = 'a'}, {.a = 0, .b = 1}};
is the obvious syntax for initializer, perfectly fine for C11 and
handled correctly by gcc-4.7 or later.
Earlier versions, though, break on it - declaration is fine and so's
access to fields (i.e. x[0].c = 'a'; would produce the right code), but
members of the anon structs and unions are not inserted into the right
namespace. Tellingly, those older versions will not barf on struct {int
a; struct {int a;};}; - looks like they just have it hacked up somewhere
around the handling of . and -> instead of doing the right thing.
The easiest way to deal with that crap is to turn initialization of
those fields (in the only place where we have such initializer of
iov_iter) into plain assignment.
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vinayak Menon