[ Upstream commit b38e7819ca ]
Keyu Man reported that the ICMP rate limiter could be used
by attackers to get useful signal. Details will be provided
in an upcoming academic publication.
Our solution is to add some noise, so that the attackers
no longer can get help from the predictable token bucket limiter.
Fixes: 4cdf507d54 ("icmp: add a global rate limitation")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Keyu Man <kman001@ucr.edu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0da7536fb4 ]
When no full socket is available, skbs are sent over a per-netns
control socket. Its sk_mark is temporarily adjusted to match that
of the real (request or timewait) socket or to reflect an incoming
skb, so that the outgoing skb inherits this in __ip_make_skb.
Introduction of the socket cookie mark field broke this. Now the
skb is set through the cookie and cork:
<caller> # init sockc.mark from sk_mark or cmsg
ip_append_data
ip_setup_cork # convert sockc.mark to cork mark
ip_push_pending_frames
ip_finish_skb
__ip_make_skb # set skb->mark to cork mark
But I missed these special control sockets. Update all callers of
__ip(6)_make_skb that were originally missed.
For IPv6, the same two icmp(v6) paths are affected. The third
case is not, as commit 92e55f412c ("tcp: don't annotate
mark on control socket from tcp_v6_send_response()") replaced
the ctl_sk->sk_mark with passing the mark field directly as a
function argument. That commit predates the commit that
introduced the bug.
Fixes: c6af0c227a ("ip: support SO_MARK cmsg")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reported-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __icmp_send() there is a possibility that the rt->dst.dev is NULL,
e,g, with tunnel collect_md mode, which will cause kernel crash.
Here is what the code path looks like, for GRE:
- ip6gre_tunnel_xmit
- ip6gre_xmit_ipv4
- __gre6_xmit
- ip6_tnl_xmit
- if skb->len - t->tun_hlen - eth_hlen > mtu; return -EMSGSIZE
- icmp_send
- net = dev_net(rt->dst.dev); <-- here
The reason is __metadata_dst_init() init dst->dev to NULL by default.
We could not fix it in __metadata_dst_init() as there is no dev supplied.
On the other hand, the reason we need rt->dst.dev is to get the net.
So we can just try get it from skb->dev when rt->dst.dev is NULL.
v4: Julian Anastasov remind skb->dev also could be NULL. We'd better
still use dst.dev and do a check to avoid crash.
v3: No changes.
v2: fix the issue in __icmp_send() instead of updating shared dst dev
in {ip_md, ip6}_tunnel_xmit.
Fixes: c8b34e680a ("ip_tunnel: Add tnl_update_pmtu in ip_md_tunnel_xmit")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
it expects a unsigned int, but got a __be32
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
this_cpu_read(*X) is faster than *this_cpu_ptr(X)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add __icmp_send function having ip_options struct parameter
Signed-off-by: Sergey Nazarov <s-nazarov@yandex.ru>
Reviewed-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply use icmp_sk_exit() when inet_ctl_sock_create() fail in icmp_sk_init().
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We'll need this to handle ICMP errors for tunnels without a sending socket
(i.e. FoU and GUE). There, we might have to look up different types of IP
tunnels, registered as network protocols, before we get a match, so we
want this for the error handlers of IPPROTO_IPIP and IPPROTO_IPV6 in both
inet_protos and inet6_protos. These error codes will be used in the next
patch.
For consistency, return sensible error codes in protocol error handlers
whenever handlers can't handle errors because, even if valid, they don't
match a protocol or any of its states.
This has no effect on existing error handling paths.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the cookie in one location to reduce code duplication and
avoid bugs from inconsistent initialization, such as that fixed in
commit 9887cba199 ("ip: limit use of gso_size to udp").
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a transmit_time field to struct inet_cork, then copy the
timestamp from the CMSG cookie at ip_setup_cork() so we can
safely copy it into the skb later during __ip_make_skb().
For the raw fast path, just perform the copy at raw_send_hdrinc().
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use BUG_ON instead of if condition followed by BUG in icmp_timestamp.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ICMP implementation currently replies to an ICMP time exceeded message
(type 11) with an ICMP host unreachable message (type 3, code 1).
However, time exceeded messages can either represent "time to live exceeded
in transit" (code 0) or "fragment reassembly time exceeded" (code 1).
Unconditionally replying to "fragment reassembly time exceeded" with
host unreachable messages might cause unjustified connection resets
which are now easily triggered as UFO has been removed, because, in turn,
sending large buffers triggers IP fragmentation.
The issue can be easily reproduced by running a lot of UDP streams
which is likely to trigger IP fragmentation:
# start netserver in the test namespace
ip netns add test
ip netns exec test netserver
# create a VETH pair
ip link add name veth0 type veth peer name veth0 netns test
ip link set veth0 up
ip -n test link set veth0 up
for i in $(seq 20 29); do
# assign addresses to both ends
ip addr add dev veth0 192.168.$i.1/24
ip -n test addr add dev veth0 192.168.$i.2/24
# start the traffic
netperf -L 192.168.$i.1 -H 192.168.$i.2 -t UDP_STREAM -l 0 &
done
# wait
send_data: data send error: No route to host (errno 113)
netperf: send_omni: send_data failed: No route to host
We need to differentiate instead: if fragment reassembly time exceeded
is reported, we need to silently drop the packet,
if time to live exceeded is reported, maintain the current behaviour.
In both cases increment the related error count "icmpInTimeExcds".
While at it, fix a typo in a comment, and convert the if statement
into a switch to mate it more readable.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ip_options_echo() uses the current network namespace, and
currently retrives it via skb->dst->dev.
This commit adds an explicit 'net' argument to __ip_options_echo()
and update all the call sites to provide it, usually via a simpler
sock_net().
After this change, __ip_options_echo() no more needs to access
skb->dst and we can drop a couple of hack to preserve such
info in the rx path.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch wants access to the fib result on an output route lookup
with the rcu lock held. Refactor __ip_route_output_key_hash, pushing
the logic between rcu_read_lock ... rcu_read_unlock into a new helper
with the fib_result as an input arg.
To keep the name length under control remove the leading underscores
from the name and add _rcu to the name of the new helper indicating it
is called with the rcu read lock held.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ECMP hash policy choice via a new sysctl
called fib_multipath_hash_policy and also adds support for L4 hashes.
The current values for fib_multipath_hash_policy are:
0 - layer 3 (default)
1 - layer 4
If there's an skb hash already set and it matches the chosen policy then it
will be used instead of being calculated (currently only for L4).
In L3 mode we always calculate the hash due to the ICMP error special
case, the flow dissector's field consistentification should handle the
address order thus we can remove the address reversals.
If the skb is provided we always use it for the hash calculation,
otherwise we fallback to fl4, that is if skb is NULL fl4 has to be set.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to avoid the atomic operation in icmp{v6,}_xmit_lock,
by checking the sysctl_icmp_msgs_per_sec ratelimit before these calls,
as pointed out by Eric Dumazet, but the BH disabled state must be correct.
The icmp_global_allow() call states it must be called with BH
disabled. This protection was given by the calls icmp_xmit_lock and
icmpv6_xmit_lock. Thus, split out local_bh_disable/enable from these
functions and maintain it explicitly at callers.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch split the global and per (inet)peer ICMP-reply limiter
code, and moves the global limit check to earlier in the packet
processing path. Thus, avoid spending cycles on ICMP replies that
gets limited/suppressed anyhow.
The global ICMP rate limiter icmp_global_allow() is a good solution,
it just happens too late in the process. The kernel goes through the
full route lookup (return path) for the ICMP message, before taking
the rate limit decision of not sending the ICMP reply.
Details: The kernels global rate limiter for ICMP messages got added
in commit 4cdf507d54 ("icmp: add a global rate limitation"). It is
a token bucket limiter with a global lock. It brilliantly avoids
locking congestion by only updating when 20ms (HZ/50) were elapsed. It
can then avoids taking lock when credit is exhausted (when under
pressure) and time constraint for refill is not yet meet.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 9a99d4a50c ("icmp: avoid allocating large struct
on stack"), because struct icmp_bxm no really a large struct, and
allocating and free of this small 112 bytes hurts performance.
Fixes: 9a99d4a50c ("icmp: avoid allocating large struct on stack")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, icmp_rcv() always return zero on a packet delivery upcall.
To make its behavior more compliant with the way this API should be
used, this patch changes this to let it return NET_RX_SUCCESS when the
packet is proper handled, and NET_RX_DROP otherwise.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp_send is called in response to some event. The skb may not have
the device set (skb->dev is NULL), but it is expected to have an rt.
Update icmp_route_lookup to use the rt on the skb to determine L3
domain.
Fixes: 613d09b30f ("net: Use VRF device index for lookups on TX")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ICMP_INC_STATS_BH() to __ICMP_INC_STATS()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP timestamp messages and IP source route options require
timestamps to be in milliseconds modulo 24 hours from
midnight UT format.
Add inet_current_timestamp() function to support this. The function
returns the required timestamp in network byte order.
Timestamp calculation is also changed to call ktime_get_real_ts64()
which uses struct timespec64. struct timespec64 is y2038 safe.
Previously it called getnstimeofday() which uses struct timespec.
struct timespec is not y2038 safe.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert the commit e2ca690b65 ("ipv4/icmp: redirect messages
can use the ingress daddr as source"), which tried to introduce a more
suitable behaviour for ICMP redirect messages generated by VRRP routers.
However RFC 5798 section 8.1.1 states:
The IPv4 source address of an ICMP redirect should be the address
that the end-host used when making its next-hop routing decision.
while said commit used the generating packet destination
address, which do not match the above and in most cases leads to
no redirect packets to be generated.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows configuring how the source address of ICMP
redirect messages is selected; by default the old behaviour is
retained, while setting icmp_redirects_use_orig_daddr force the
usage of the destination address of the packet that caused the
redirect.
The new behaviour fits closely the RFC 5798 section 8.1.1, and fix the
following scenario:
Two machines are set up with VRRP to act as routers out of a subnet,
they have IPs x.x.x.1/24 and x.x.x.2/24, with VRRP holding on to
x.x.x.254/24.
If a host in said subnet needs to get an ICMP redirect from the VRRP
router, i.e. to reach a destination behind a different gateway, the
source IP in the ICMP redirect is chosen as the primary IP on the
interface that the packet arrived at, i.e. x.x.x.1 or x.x.x.2.
The host will then ignore said redirect, due to RFC 1122 section 3.2.2.2,
and will continue to use the wrong next-op.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP packets are inspected to let them route together with the flow they
belong to, minimizing the chance that a problematic path will affect flows
on other paths, and so that anycast environments can work with ECMP.
Signed-off-by: Peter Nørlund <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace calls to vrf_master_ifindex_rcu and vrf_master_ifindex with either
l3mdev_master_ifindex_rcu or l3mdev_master_ifindex.
The pattern:
oif = vrf_master_ifindex(dev) ? : dev->ifindex;
is replaced with
oif = l3mdev_fib_oif(dev);
And remove the now unused vrf macros.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer caches based on address only, so duplicate IP addresses within
a namespace return the same cached entry. Enhance the ipv4 address key
to contain both the IPv4 address and VRF device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently inet_addr_type and inet_dev_addr_type expect local addresses
to be in the local table. With the VRF device local routes for devices
associated with a VRF will be in the table associated with the VRF.
Provide an alternate inet_addr lookup to use a specific table rather
than defaulting to the local table.
inet_addr_type_dev_table keeps the same semantics as inet_addr_type but
if the passed in device is enslaved to a VRF then the table for that VRF
is used for the lookup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with ingress use the index of VRF master device for route lookups on
egress. However, the oif should only be used to direct the lookups to a
specific table. Routes in the table are not based on the VRF device but
rather interfaces that are part of the VRF so do not consider the oif for
lookups within the table. The FLOWI_FLAG_VRFSRC is used to control this
latter part.
Signed-off-by: Shrijeet Mukherjee <shm@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input() unconditionally overwrites the dst. Hide the original
dst attached to the skb by calling skb_dst_set(skb, NULL) prior to
ip_route_input().
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 code uses a mixture of coding styles. In some instances check
for NULL pointer is done as x == NULL and sometimes as !x. !x is
preferred according to checkpatch and this patch makes the code
consistent by adopting the latter form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of nr_cpu_ids and use modern percpu allocation.
Note that the sockets themselves are not yet allocated
using NUMA affinity.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If icmp_rcv() has successfully processed the incoming ICMP datagram, we
should use consume_skb() rather than kfree_skb() because a hit on the likes
of perf -e skb:kfree_skb is not called-for.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common dynamic_debug capable net_dbg_ratelimited
and remove the LIMIT_NETDEBUG macro.
All messages are still ratelimited.
Some KERN_<LEVEL> uses are changed to KERN_DEBUG.
This may have some negative impact on messages that were
emitted at KERN_INFO that are not not enabled at all unless
DEBUG is defined or dynamic_debug is enabled. Even so,
these messages are now _not_ emitted by default.
This also eliminates the use of the net_msg_warn sysctl
"/proc/sys/net/core/warnings". For backward compatibility,
the sysctl is not removed, but it has no function. The extern
declaration of net_msg_warn is removed from sock.h and made
static in net/core/sysctl_net_core.c
Miscellanea:
o Update the sysctl documentation
o Remove the embedded uses of pr_fmt
o Coalesce format fragments
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current ICMP rate limiting uses inetpeer cache, which is an RBL tree
protected by a lock, meaning that hosts can be stuck hard if all cpus
want to check ICMP limits.
When say a DNS or NTP server process is restarted, inetpeer tree grows
quick and machine comes to its knees.
iptables can not help because the bottleneck happens before ICMP
messages are even cooked and sent.
This patch adds a new global limitation, using a token bucket filter,
controlled by two new sysctl :
icmp_msgs_per_sec - INTEGER
Limit maximal number of ICMP packets sent per second from this host.
Only messages whose type matches icmp_ratemask are
controlled by this limit.
Default: 1000
icmp_msgs_burst - INTEGER
icmp_msgs_per_sec controls number of ICMP packets sent per second,
while icmp_msgs_burst controls the burst size of these packets.
Default: 50
Note that if we really want to send millions of ICMP messages per
second, we might extend idea and infra added in commit 04ca6973f7
("ip: make IP identifiers less predictable") :
add a token bucket in the ip_idents hash and no longer rely on inetpeer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_local_deliver_finish() already have a rcu_read_lock/unlock, so
the rcu_read_lock/unlock is unnecessary.
See the stack below:
ip_local_deliver_finish
|
|
->icmp_rcv
|
|
->icmp_socket_deliver
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet